Quick Installation Guide

Connecting the Ramp Timer Pro to the Orbit Marine

1. Connect your 12VDC transformer to the female DC plug on the timer.

2. Connect your LED light(s) to the male DC plugs on the timer. Blue light channel (dawn/dusk/moonlight) connects to Line 1. White light channel (daylight) connects to Line 2.

3. Remove plastic cover from wireless remote and remove clear plastic tab located at the bottom of the remote.

4. Locate a dry location not near water or salt creep. Clean area thorougly.

5. Use velcro (included) to mount Ramp Timer Pro to mounting location.

Page 1

IR Sensor

6. Press SET CLOCK

7. Press HOUR and MINUTE until the current time of day is displayed

8. Press ENTER clock is now set

9. Press TIMER M1 or TIMER M3 . Pre-programmed lighting schedule is complete.**

** See following page for pre-programmed lighting schedules.Note: Ramp Timer Pro and remote are NOT waterproof. Ensure neither are located in a location of splashing water or salt creep.

Installing the Orbit Marine1. Unpack light fixture and components, remove any plastic film on light fixture.

2. Slide the adjustable docking legs on the side of the fixture to match the length of your aquarium.

3. Set fixture on aquarium and connect to the Ramp Timer Pro (included) as per instructions below.

, plug transformer into GFCI protected

Orbit Marine LED Light Fixture

12VDC Transformer

AC outlet. Ensure a drip loop is created before the outlet as shown on page 6.

Orbit Marine LED Lightwith 24 hour Ramp Timer Pro LED Controller

Ramp Timer Pro Controller

What’s included:1 - Orbit Marine LED light fixture with dual actinic/dual daylight LEDs with adjustable docking legs1 - 12VDC transformer1 - Ramp Timer Pro LED controller1 - Wireless IR remote

Pre-programmed Lighting Schedule Guide

The Ramp Timer Pro features four pre-programmed lighting schedules. These schedules are located in memory buttons labeled TIMER M1, TIMER M2, TIMER M3, TIMER M4. To customize any of the settings, please follow the detailed Programming Instructions located on Page 4.

Using the graph and table below, select from any one of the pre-programmed lighting schedules. Once you select a lighting program, simplypress TIMER M1, TIMER M2, TIMER M3 or TIMER M4 and the controller will automatically enter into the selected lighting schedule.

Page 2

Detailed Installation Instructions

Please read the following guides before following the detailed programminginstructions located on page 4.

Programming Feature Guide

The Ramp Timer Pro features two independent lighting channels with the following:- Program on/off times for each channel- Adjustable intensity (0-100%) for each channel- Adjustable ramp up (sunrise) / dim down (sunset) (0-30 minutes)- Adjustable moonlight duration (0-6 hours)- On-demand color spectrum adjustment- On-demand weather simulation including cloud cover, fading moonlight and storm with lightning- Four memory locations for storing custom lighting schedules each are pre-programmed by default, see below.

p00 15

Wireless Infrared IR Remote Guide

When using your wireless remote, point the remote directly at the IR sensor located on the Ramp Timer Pro. It is important to have a direct line of sight between the remote and the controller.

Digital LCD Display Guide

Page 3

SunriseSunset

Detailed Programming Instructions

The following detailed steps will guide you through customizing and programming your Ramp Timer Pro. Please be sure to follow our Quick Installation Guide and set the clock before following the below steps.

Programming Individual Lighting Channels

The Ramp Timer Pro features two channels of lighting which can be independently controlled. Channel 1/Line 1 should be connected to your blue spectrum lights for dawn/dusk/actinic/moon lighting; Channel 2/Line 2 should be connected to your white spectrum lights for daylight.

SUNRISE/SUNSET FADE - The duration of the ramp up and dim down (0-30 minutes)

To reset the memory settings to the factory default, press DEFAULT for 5 seconds (see pg. 5).Default

This will reset the controller memory for all four memory settings.

Page 4

Programming Light Channels continued

Memory Functions

2.

per the programmed moonlight duration time (0-6 hours.)

Press TIMER M1, TIMER M2, TIMER M3, or TIMER M4. SL-1, SL-2, SL-3 or SL-4 will display on the screen..

The intensity % can be used as a reference when programming your minimum and maximum settings.

and will display

Page 6

AC Power Cord

Drip Loop

AC ProtectedGFCI Outlet