options for the lm guide - thk technical support · for options for the lm guide not mentioned in...

Options for the LM GuideQZ LubricatorLaminated Contact Scraper LaCSSide Scraper Light Sliding Resistance Contact Seal LiCSGC Cap Dedicated for LM Rail Mounting Holes N E W

CATALOG No.321-2E

1

OPTIONSFor LM Guides, dust-prevention and lubrication accessories are available. You can make a selection according to the application or mounting location.

Light Sliding ResistanceContact Seal LiCS

Side Scraper

Laminated Contact Scraper LaCS

QZ Lubricator

Light Sliding Resistance Contact Seal LiCS（P.15 onward）

Metal scraper

Laminated Contact Scraper LaCS（P.9 onward）

Intermediate plate

Spacer

End seal

Double seals

Metal cap dedicated for LM rail mounting holes model GC (P.17 onward)

Plate cover model SV

2

Dedicated bellows

QZ Lubricator（P.5 onward）

Side scraper case

Side scraper (P.14)

Side scraper separator

● For options for the LM Guide not mentioned in this catalog (bellows, etc.), see the general catalog.●Options for the Ball Screw (QZ Lubricator, wiper ring W) are also available.

3

Seals and a Metal ScraperIn addition to LaCS and LiCS, THK also offers other options, such as an end seal made of special synthetic rubber with high wearresistance and a side seal, designed to increase the dust prevention effect.

For LM Guide models supported for dust prevention accessories and the overall LM block length (dimension L) with the desired dust prevention accessoryattached, see page 11.

End seal

End sealUsed in locations exposed to dust

End seal

Double sealsUsed in locations exposed to much dust or many cuttingchips

Metal scraper

Metal scraper (non-contact)Used in locations where welding spatter may adhere to the LM rail

Side seal

Side sealUsed in locations where dust mayenter the LM block from its side orbottom surface, such as vertical,horizontal and inverted mounts

Inner seal

Inner sealUsed in locations severely exposed todust or cutting chips

■Table of Symbols for Options

SymbolUUSSDDZZKKGGPP

SSHHDDHHZZHHKKHHQZUUQZSSQZDDQZZZQZKKQZGGQZPP

QZSSHHQZDDHHQZZZHHQZKKHH

Dust prevention accessoriesEnd sealEnd seal + side seal + inner sealDouble seals + side seal + inner sealEnd seal + side seal + inner seal + metal scraperDouble seals + side seal + inner seal + metal scraperLiCSLiCS + side seal + inner sealEnd seal + side seal + inner seal + LaCSDouble seals + side seal + inner seal + LaCSEnd seal + side seal + inner seal + metal scraper + LaCSDouble seals + side seal + inner seal + metal scraper + LaCSEnd seal + QZEnd seal + side seal + inner seal + QZDouble seals + side seal + inner seal + QZEnd seal + side seal + inner seal + metal scraper + QZDouble seals + side seal + inner seal + metal scraper + QZLiCS + QZLiCS + side seal + inner seal + QZEnd seal + side seal + inner seal + LaCS + QZDouble seals + side seal + inner seal + LaCS + QZEnd seal + side seal + inner seal + metal scraper + LaCS + QZDouble seals + side seal + inner seal + metal scraper + LaCS + QZ

Various combinations of options are available. See the table below for symbols for specific options.

4

■Table of LM Guide Models and CorrespondingOptions (QZ, LaCS, LiCS and Side Scraper)

○ : available

－ : unavailable

＊1: For models HSR15 to 65, a low-resistance end seal is also available (symbol: LL)

＊2: “SS” is also applicable to some types of model RSR-Z.

Model No.

Dust prevention

LiCS

SS DD ZZ KK HH

LaCS

SHS

SSR

SNR/SNS

SHW12 to 14

17 to 50

SRS7 to 15

20 to 25

SCR

15

SRG 20 to 65

85 to 100

SRW70 to 100

130 to 150

HSR＊1

NR/NRS

RSR＊29 to 15

9W to 15W

UU GG PP

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

－

－

○

○

○

－

○

－

－

○

○

○

○

○

○

○

○

－

－

○

○

○

－

○

－

－

○

－

○

○

○

○

○

○

－

－

○

○

○

－

○

－

－

○

－

○

○

○

○

○

○

－

－

○

○

○

－

○

－

○

○

○

○

－

○

－

○

○

－

－

－

○

－

－

－

－

－

－

○

－

－

－

－

－

－

－

－

－

－

－

－

－

－

－

－

○

－

－

－

－

－

－

－

－

○

○

○

○

○

○

○

○

○

○

－

○

○

○

○

○

○

－

－

○

－

－

－

－

－

－

－

－

－

－

－

－

－

－

Lubrication

QZ

SideScraper

QZLubricator

5

QZ Lubricator QZ

The QZ Lubricator feeds the right amount of lubricant to the raceway of the LM rail. This allows an oil filmto be constantly formed between the rolling elements and the ball raceway, thus significantly extending thelubrication maintenance interval.

Features● Since it supplements an oil loss, the lubrication

maintenance interval can be significantly extended.● Since the right amount of lubricant is applied to the

ball raceway, an environmentally friendly lubricationsystem that does not contaminate the surroundingsis achieved.

● It allows the user to select a lubricant that meets theintended use.

ApplicationsThe QZ Lubricator provides an optimal lubricationsystem for the following requirements. ● To introduce an eco-friendly machine.● To prevent contaminating the surroundings of the machine/

equipment.● To eliminate the waste of grease or oil used in the LM Guide.● To minimize the piping of the machine.● To extend the greasing interval or want to stop greasing.● To lubricate the machine only with oil (want to avoid grease

lubrication).

(End seal)

Flow of lubricant

(3) Oil control plate

Ball cage

Ball

Casing (2) High-density fiber net

(1) Highly oil-impregnated fiber net

The structure of the QZ Lubricator consists of three major components:

(1) A highly oil-impregnated fiber net (functions to store a lubricant)

(2) A high-density fiber net (functions to apply the lubricant to the raceway)

(3) An oil control plate (functions to control the flow of the lubricant)

The lubricant contained in QZ Lubricator is fed to the LM system based onthe principle of capillary action, which is used in felt-tip pens and otherproducts.

Grease lubrication

Forced centralized lubrication

QZ Lubricator

LM Guide attached with the QZ Lubricator

Significantly Extended Maintenance IntervalAttaching the QZ Lubricator helps extend the maintenance intervalthroughout the whole load range from the light-load area to theheavy-load area.

Note 1: The QZ Lubricator has an air vent. Do not block the vent with grease or the like.Note 2: Those LM Guide models attached with the QZ Lubricator cannot have a grease nipple. When desiring both the QZ Lubricator and a grease nipple to be attached,

contact THK.Note 3: The QZ Lubricator is not sold alone.

6

■ Significantly Extended Maintenance IntervalAttaching the QZ Lubricator helps extend the maintenance interval throughout the whole load range from thelight-load area to the heavy-load area.

30000km

3500km

0 500 1000 1500 3500 30000

Grease lubrication only

Grease + QZ Lubricator


Service life: 465km


Calculated service life under a heavy load = 400km

Distance traveled (km)LM Guide Running Test without Replenishment of Lubricant

Light load

1.4kN

300m/min

Medium load

9.3kN

50m/min

3200km

Heavy load

18.6kN

50m/min

400km

Conditions

Load

VelocityCalculated service life

LM Guide : Model HSR35R1SS

Hea

vy lo

adM

ediu

m

load

Ligh

t lo

ad

Service life: 962km Grease : 2 cc/LM block, initial lubrication only

QZ Lubricator : 5 cc × 2/LM block, initial lubrication only

■ Effective Use of LubricantSince the QZ Lubricator feeds the right amount of lubricant to the right place, the lubricant can be usedefficiently.

Amount of oil contained in the QZ Lubricator0.166 cm3×1 lubricator/2 lubricators

= 0.332 cm3

Forced lubrication0.03 cm3/6 min×16667 min

= 83.3 cm3

Compared

Lubricant consumption is 1/250 of that of forced lubrication, thus significantly reducing the waste of lubricant.

Forced lubrication 83.3

SHW21QZ

0 20 40 60 80 100Supplied amount of lubricant: cm3

Test conditions: 300m/min

0.332

Comparison of lubricant consumption after traveling

5,000km

■ Lubrication Support Effect in a Harsh EnvironmentAs a result of conducting a durability test in a harsh environment (environment with coolant, foreignmaterial), a travel distance of 5,000 km was achieved.

0 1000 2000 3000 4000 5000 6000

QZ+LaCS

Standard typemodel HSR45

SNS45

Distance traveled (km)

No breakage

Flaking occurs at 3,500km

［Test result］［Test conditions］

Model No.

Load

Velocity

Coolant

SNS45

P = 0.1 C

60m/min

Immersed 48 hours, dried 96 hours

Foundry dust (125 µm or less)

HSR45

Lubrication AFA Grease + QZSuper Multi 68Operating cycle : 0.1 cc/shotPeriodic time: 16min

Foreign material

Performance

7

LM Block Length (Dimension L) with QZ Attached (Standard LM block length)

Overall LM block length with QZ attached

L

SNR/SNS

SSR

SHS

SHW

SRS

Model No.

L

Standard LMblock length

15C/V/R15LC/LV20C/V20LC/LV25C/V/R25LC/LV/LR30C/V/R30LC/LV/LR35C/V/R35LC/LV/LR45C/V/R45LC/LV/LR55C/V/R55LC/LV/LR65C/V65LC/LV15XVY15XWY/XTBY20XV20XW/XTB25XVY25XWY/XTBY30XW35XW25R/C25LR/LC30R/C30LR/LC35R/C/RH/CH35LR/LC/LRH/LCH45R/C/RH/CH45LR/LC/LRH/LCH55R/C/RH/CH55LR/LC/LRH/LCH65R/C65LR/LC12 CAM/CRM12 HRM14 CAM/CRM17 CAM/CRM21 CA/CR27 CA/CR35 CA/CR50 CA/CR77W99N9W9WN1212N12W12WN1515N15W15WN2025

QZUU

106.6121.6124.2143.2141.6158.6160.4185.4180.2210.2212246246.4288.4303.6354.6

82.599.193

111.8109.8132.8151.5168.3132.5151.7153.9176.4176.9202.4209.8242.6244.4281.6271.3331.3－－－82.498.2

117.6158.8196.6－－－－－－－－－－－－－－－－

QZSS QZDD QZZZ QZKK QZSSHH QZDDHH QZZZHH QZKKHH

101.2116.2117.8136.8134.4151.4151.8176.8170.4200.4202.2236.2235.2277.2291.2342.2

76.793.386.1

104.9102.4125.4143.4159.3124.9144.1144.1166.6166.7192.2199.6232.4234.2271.4260.7320.7－－－79.493.2

111.8151.4188.4－－－－－－－－－－－－－－－－

105.4120.4121.8140.8139.2156.2158183177.8207.8208.8242.8243.2285.2300.4351.4

81.397.990.6

109.4107.4130.4149.1165.9130.1149.3151.5174174.5200206.6239.4241.2278.4268.1328.1－－－81.296.6

115.2156.4194.2－－－－－－－－－－－－－－－－

100115115.4134.4132149149.4174.4168198199233232274288339

75.592.183.7

102.5100123141156.9122.5141.7141.7164.2164.3189.8196.4229.2231268.2257.5317.5

5871.470.778.291.6

109.4149186－－52.462.460.672.35669.166.181.169.28781.7100.9

83.2112.6

92.2107.2109.4128.4127.6144.6142.4167.4162.2192.2191225225.4267.4278.6329.6

68.585.17997.895.8

118.8133.5150.3118.5137.7136.7159.2159.7185.2189.2222223.4260.6246.9306.9－－－68.483.6

103139.4175.6－－－－－－－－－－－－－－－－

86.8101.8103122120.4137.4133.8158.8152.4182.4181.2215.2214.2256.2266.2317.2

62.779.372.190.988.4

111.4125.4141.3110.9130.1126.9149.4149.5175179211.8213.2250.4236.3296.3－－－65.478.697.2

132167.4－－－－－－－－－－－－－－－－

89.8104.8105.4124.4121.6138.6136161154.8184.8182.8216.8216.6258.6268.6319.6

65.181.773.191.990

113127.8143.3112.8132131153.5152.9178.4181.6214.4214.7251.9238.2298.2－－－668098.6

134.4169.2－－－－－－－－－－－－－－－－

84.499.499

118114.4131.4127.4152.4145175173207205.4247.4256.2307.2

59.375.966.28582.6

105.6119.7134.3105.2124.4121.2143.7142.7168.2171.4204.2204.5241.7227.6287.6

4760.455.5637592.8

127161

33.44140.850.84960.744.457.154.569.55572.867.586.56697

84.499.499

118114.4131.4127.4152.4145175173207205.4247.4256.2307.2

59.375.966.28582.6

105.6119.7134.3105.2124.4121.2143.7142.7168.2171.4204.2204.5241.7227.6287.6

4760.455.5637592.8

127161

33.44140.850.84960.744.457.154.569.55572.867.586.56697

64.479.4799892

109106131122152140174171213221272

40.356.947.766.5608397

110.982.8

10298

120.5109.5135138.2171163.3200.5186246

3750.445.5515972.8

107141

23.43130.840.83950.734.447.144.559.54360.855.574.55077

Unit: mm

8

HSR

SRW

SRG

SRG/SRN

Model No.

L


15S20S20253035456515A/V20A/V20LA/LV25C/R25LC/LR30C/R30LC/LR35C/R35LC/LR45C/R45LC/LR55C/R55LC/LR65LC/LV708510015A/B/R/YR20A/B/R/CA/CB/YR20LA/LB/LR/HA/HB25A/B/R/CA/CB/YR25LA/LB/LR/HA/HB30A/B/R/CA/CB/YR30LA/LB/LR/HA/HB35A/B/R/CA/CB/YR35LA/LB/LR/HA/HB45A/B/R/CA/CB/YR45LA/LB/LR/HA/HB55A/B/R/CA/CB/YR55LA/LB/LR/HA/HB65A/B/R/CA/CB/YR65LA/LB/LR/HA/HB25XR/XA/XB25XLR/XLA/XLB30R/A/B30LR/LA/LB35R/A/B35LR/LA/LB45R/A/B45LR/LA/LB55R/A/B55LR/LA/LB65R/A/B65LR/LA/LB99N9W9WN1212N12W12WN1515N15W15WN

QZUU

106.9124.5143.5158.6185.4210.2246354.6

—129.6149.6154.1173.7171.6195.6188.8218.8224.4259.4264.4314.4389.8259.4314.4389.8108124.2140.2131.8150.9150.7173.3166.8192.2

——————

132.5151.7153.1175.6176.9202.4211243244.7281.9271.9331.9

————————————

QZSS QZDD QZZZ QZKK QZSSHH QZDDHH QZZZHH QZKKHH

101.4118137151.4176.8200.4236.2342.2

—127.6147.6147.7167.3164.6188.6181211215.2250.2255.2305.2378.6250.2305.2378.6100116132123.8142.9142.7165.3157182.4

——————

124.9144.1144.1166.6166.7192.2200.8232.8234.5271.7261.3321.3

————————————

105.4122141156.2183207.8242.8351.4

—127.2147.2151.7171.3169.2193.2186.4216.4221.2256.2261.2311.2391.6256.2311.2391.6106.8121.8137.8129.4148.5148.3170.9164.4189.8

——————

130.1149.3150.7173.2174.5200207.8239.8241.5278.7268.7328.7

————————————

100.4115.5134.5149174.4198233339

—125.2145.2145.3164.9160.8184.8178.6208.6212247252302380.4247302380.4

98.8113.6129.6121.4140.5140.3162.9154.6180

——————

122.5141.7141.7164.2164.3189.8197.6229.6231.3268.5258.1318.1

————————————

92.2109.4128.4144.6167.4192.2225329.6

—113133135.5155.1153177171.2201.2203.4238.4243.4293.4370.4238.4293.4370.4

92.2110.2126.2117.8136.9132.7155.3148.8174.2186.4218.2213.2251.3239298.5118.5137.7135.1157.6159.7185.2190222223.7260.9246.9306.9

————————————

86.8103122137.4158.8182.4215.2317.2

—111131130.5150.1146170163.4193.4194.2229.2234.2284.2354.2229.2284.2354.2

84.2102118109.8128.9124.7147.3139164.4176.6208.4202240.1226.6286.1110.9130.1126.1148.6149.5175179.8211.8213.5250.7236.3296.3

————————————

89.8105.4124.4138.6161184.8216.8319.6

92.6109.6129.6130.5150.1148172162.8192.8194.2229.2234.2284.2354.2229.2284.2354.2

87.6104.4120.4112.1131.2127149.6142167.4181.6213.4208.4246.5233.8293.3112.8132129.4151.9152.9178.4182.4214.4215252.2238.2298.2

————————————

84.499

118131.4152.4175207307.2

90.6107.6127.6125.5145.1141165155185185220225275343220275343

79.696.2

112.2104.1123.2119141.6132.2157.6174.8206.6197.2235.3221.4280.9105.2124.4120.4142.9142.7168.2172.2204.2204.8242227.6287.6

————————————

84.499

118131.4152.4175207307.2

90.6107.6127.6125.5145.1141165155185185220225275 343220275343

79.696.2

112.2104.1123.2119141.6132.2157.6174.8206.6197.2235.3221.4280.9105.2124.4120.4142.9142.7168.2172.2204.2204.8242227.6287.6

40.850.84960.74557.754.569.554.972.767.586.5

64.47998

109131152174272

69.286.2

106.295.5

115.1111 135 125155155190185235303190235303

56.6749083.1

102.298

120.6109.4134.8139170.8163201.1186245.5

82.8102

98120.5109.5135139171162.8200185.6245.6

30.840.83950.73547.744.559.542.960.755.574.5

NR/NRS

RSR

Units: mm

SCR

Model No. Type of LM block

With QZLubricatorattached

LM rail length(in mm)

With steeltape attached Number of rails used

on the same plane

Number of LM blockson the same rail

Symbol for dustprevention

option

Symbol for radial clearanceNormal (no symbol), light preload (C1), medium preload (C0)

Accuracy symbolNormal grade (no symbol), high grade (H), precision grade (P),super precision grade (SP), ultra-super precision grade (UP)

This model number indicates that a single-rail unit constitutes one set (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum).

Those models attached with the QZ Lubricator cannot have a grease nipple.Note

SHS25 LC 2 QZ KKHH C0 +1200L P Z -ⅡExample of model number coding

9

Laminated ContactScraper LaCS

For locations with an adverse atmosphere, Laminated Contact Scraper LaCS is available.LaCS removes minute foreign material adhering to the LM rail in multiple stages and prevents it from enteringthe LM block with its laminated contact structure (3-layer scraper).

Features● Since the 3 layers of scrapers fully contact the LM rail,

LaCS is highly capable of removing minute foreignmaterial.

● Since it uses oil-impregnated foam synthetic rubber with aself-lubricating function, low friction resistance is achieved.

Basic Specifications of LaCS● Service temperature range of LaCS: -20℃ to +80℃● Resistance of LaCS: see the table below.

Ball

Ball cage

Liquid

Large amount of foreign material

Laminated Contact Scraper LaCS

Optimal for use in harsh environmentssubject to foreign material such as finedust and liquids.

Note 1: LaCS is not sold alone.Note 2: For the maximum service speed of LaCS, contact THK.

Note: Each resistance value in the table represents the maximum resistance value of LaCS when one unit of LaCS is attached on each of both sides of the LM block.However, the value does not include the sliding resistance of the LM block, seals, etc.

SHS

1520253035455565

Resistance of LaCS（excluding sliding resistance of the LM block and other seals）

5.96.98.1

12.815.1

5.26.5

11.718.220.826.032.539.0

Unit: N

Model No. Model No. Model No. Model No.Resistance Resistance Resistance Resistance

SSR

1520253035

SNR/SNS

SHW

253035

21273550

8.113.415.5

3.96.5

13.019.5

SCR

15202530

5.26.5

11.718.2

SRG

20253035455565

6.16.98.29.1

14.318.226.0

SRN5565

18.222.1

SRW7085100

32.839.758.3

HSR

1520253035

3.85.67.5

14.922.4

NR/NRS

25303545556585

8.113.415.523.328.639.652.7

SRS

99W12

12W15

15W2025

2.33.33.54.25.17.55.27.8

SNR/SNS

45556585

23.328.639.652.7

SCR354565

20.826.039.0

SRN3545

9.114.3

10

Performance

Item Description

Testedmodel

Maximum speed

Environmentalconditions

No. 1

No. 2

SHS45R1SS + 3000L (without LaCS)

SHS45R1SSHH + 3000L (with LaCS)

200 m/min

Coolant sprayed: 5 times/day

［Test conditions］Test environment: water solublecoolant

Magnified view of the end seal lip

No. 1without LaCS

No. 2with LaCS

0 1000 2000 3000 4000 5000

Distance traveled (km)

End seal lip fractured at 1,700 km

Still running after traveling 5,000 km

［Test result］

Item Description

Testedmodel

Maximum speed, acceleration

No. 1

No. 2

SNR45R1DD + 600L (with double seals)

SNR45R1HH + 600L (with LaCS only)

60 m/min; 1G

9.6 kN

Type: FCD450#115 (particle diameter: 125 mm or less)

Sprayed amount: 1 g/hour (total sprayed amount: 120 g)

External load

Foreignmaterial

conditions

［Test conditions］Test environment: environment withminute foreign material

n=1

n=2

n=3

n=1

n=2

n=3

Seal configuration Amount of foreign materialentering the raceway: g

Sample No.1Conventional dust

prevention (double end-seal)

Sample No.2LaCS

0.3

0.3

0.3

0.0

0.0

0.0

［Test result］Amount of foreign material entering theraceway

No. 1: without LaCS: lip fractured at 1,700 km

No. 2: with LaCS: no anomaly observed after traveling 5,000 km

fAreas marked with an arrow are fractured.

No. 1: traveled 100 km (with double seals)

No. 2: traveled 100 km (with LaCS only)

No foreign material entering the raceway is observed.

Large amount of foreign material has entered the ball raceway.

Lip has not been fractured

f

f

f

11

SNR/SNS

SSR

SHS

SHW

SRS

Model No.

LStandardLM block

length15C/V/R15LC/LV20C/V20LC/LV25C/V/R25LC/LV/LR30C/V/R30LC/LV/LR35C/V/R35LC/LV/LR45C/V/R45LC/LV/LR55C/V/R55LC/LV/LR65C/V65LC/LV15XVY15XWY/XTBY20XV20XW/XTB25XVY25XWY/XTBY30XW35XW25R/C25LR/LC30R/C30LR/LC35R/C/RH/CH35LR/LC/LRH/LCH45R/C/RH/CH45LR/LC/LRH/LCH55R/C/RH/CH55LR/LC/LRH/LCH65R/C65LR/LC85LR/LC12 CAM/CRM12 HRM14 CAM/CRM17 CAM/CRM21 CA/CR27 CA/CR35 CA/CR50 CA/CR77W99N9W9WN1212N12W12WN1515N15W15WN202515S20S202530

UU

85.2100.2102.4121.4121.6138.6140.4165.4160.2190.2182216216.4258.4273.6324.6

66.583.17795.889.8

112.8131.5148.3110.1129.3130.7153.2143.7169.2176.6209.4201.2238.4228.1288.1－－－－70.482.297.6

138.8176.6－－－－－－－－－－－－－－－－85.2102.5121.5138.6165.4

SS DD ZZ KK SSHH DDHH ZZHH KKHH

79.894.896

115114.4131.4131.8156.8150.4180.4172.2206.2205.2247.2261.2312.2

60.777.370.188.982.4

105.4123.4139.3102.5121.7120.9143.4133.5159166.4199.2191228.2217.5277.5－－－－67.477.291.8

131.4168.4－－－－－－－－－－－－－－－－79.996115131.4156.8

8499

100119119.2136.2138163157.8187.8178.8212.8213.2255.2270.4321.4

65.381.974.693.487.4

110.4129.1145.9107.7126.9128.3150.8141.3166.8173.4206.2198235.2224.9284.9－－－－69.280.695.2

136.4174.2－－－－－－－－－－－－－－－－84.4100119136.2163

78.693.693.6

112.6112129129.4154.4148178169203202244258309

59.576.167.786.580

103121136.9100.1119.3118.5141131.1156.6163.2196187.8225214.3274.3－－－－66.275.689.4

129166－－42.252.250.662.34658.756.171.157.27569.788.765.292.678.994113129154.4

72.287.289.4

108.4107.6124.6122.4147.4142.2172.2161195195.4237.4248.6299.6

50.767.360.379.173.196.1

110.8126.7

96.8116114.2136.7127.3152.8156.8189.6181.3218.5204.8264.8323.2－－－56.468.283.6

119.4155.6－－－－－－－－－－－－－－－－72.289.4108.4124.6147.4

66.881.883

102100.4117.4113.8138.8132.4162.4151.2185.2184.2226.2236.2287.2

44.961.553.472.265.788.7

102.7117.7

89.2108.4104.4126.9117.1142.6146.6179.4171.1208.3194.2254.2312.2－－－53.463.277.8

112147.4－－－－－－－－－－－－－－－－66.883102117.4138.8

69.884.885.4

104.4101.6118.6116141134.8164.8152.8186.8186.6228.6238.6289.6

47.363.954.673.467.490.4

105.1119.9

90.4109.6107.8130.3119.7145.2148.4181.2172.7209.9196.2256.2313.8－－－546478.6

114.4149.2－－－－－－－－－－－－－－－－69.885.4

104.4118.6141

64.479.4799892

109106131122152140174171213221272

40.356.947.766.5608397

110.982.8

10298

120.5109.5135138.2171163.3200.5186246302.8

3750.445.5515972.8

107141

23.43130.840.83950.734.447.144.559.54360.855.574.5507764.47998

109131

64.479.4799892

109106131122152140174171213221272

40.356.947.766.5608397

110.982.8

10298

120.5109.5135138.2171163.3200.5186246302.8

3750.445.5515972.8

107141

23.43130.840.83950.734.447.144.559.54360.855.574.5507764.47998

109131

64.479.4799892

109106131122152140174171213221272

40.356.947.766.5608397

110.982.8

10298

120.5109.5135138.2171163.3200.5186246302.8

3750.445.5515972.8

107141

23.43130.840.83950.734.447.144.559.54360.855.574.5507764.47998

109131

Unit: mm

SCR

LM Block Length (Dimension L)with LaCS and Seals Attached (Standard LM block length)

Overall LM block length with LaCS attached

L

12

＊ A grease nipple cannot be attached on types ZZ and KK of model HSR15. Contact THK for details.

HSR

NR/NRS

SRG

SRW

Model No.

LStandardLM block

lengthUU

190.2216324.6－

109.6129.6122.7142.3140.2164.2158.8188.8194.4229.4224.4274.4349.8－－

229.4274.4349.8－－－－－82.4

101.8117.8112.9132131.8154.4143.2168.6－－－－－－－－－－－

110.1129.3130.7153.2143.7169.2177.8209.8201.5238.7228.7288.7－－－－－－

SS DD ZZ KK SSHH DDHH ZZHH KKHH

180.4206.2312.2－

107.6127.6117.7137.3133.2157.2151181185.2220.2215.2265.2338.6－－

220.2265.2338.6－－－－－77.295.2

111.2105.3124.4124.2146.8135.6161－－－－－－－－－－－

102.5121.7121.7144.2133.5159167.6199.6191.3228.5218.1278.1－－－－－－

187.8212.8321.4－

107.2127.2120.3139.9137.8161.8156.4186.4191.2226.2221.2271.2346.6－－

226.2271.2346.6－－－－－81.298.6

114.6108.6127.7127.5150.1140165.4－－－－－－－－－－－

107.7126.9128.3150.8141.3166.8174.6206.6198.3235.5225.5285.5－－－－－－

178203309－

105.2125.2115.3134.9130.8154.8148.6178.6182217212262335.4－－

217262335.4－－－－－7692

108101120.1119.9142.5132.4157.8－－－－－－－－－－－

100.1119.3119.3141.8131.1156.6164.4196.4188.1225.3214.9274.9－－－－－－

172.2195299.6－91.6

111.6105.5125.1123147139.2169.2171.4206.4201.4251.4322.6376.4422.2206.4251.4322.6376.4422.2－－－63.4＊83.299.294.3

113.4109.2131.8120.6146151.4183.2175.4213.5198.4257.9259.6317－－－96.8

116113.4135.9127.3152.8157.6189.6181.6218.8204.8264.8237.6293.6267.1323.2307.2347.2

162.4185.2287.2－89.6

109.6100.5120.1116140131.4161.4162.2197.2192.2242.2311.4365.2411197.2242.2311.4365.2411－－－58.2＊76.692.686.7

105.8101.6124.2113138.4144.2176168.2206.3191.2250.7252.4309.8－－－89.2

108.4104.4126.9117.1142.6147.4179.4171.4208.6194.2254.2226.6282.6256.1312.2295.6335.6

164.8186.8289.6

71.288.2

108.2100.5120.1118142132.8162.8164.2199.2194.2244.2314.2361.2406.2199.2244.2314.2361.2406.2－－－61.880.696.690.7

109.8105.6128.2117142.4146.2178170.2208.3193.2252.7252.8310.2－－－90.4

109.6107129.5119.7145.2149.2181.2173210.2196.2256.2229285257.7313.8297.8337.8

152174272

69.286.2

106.295.5

115.1111135125155155190185235303350395190235303350395－－－56.6749083.1

102.298

120.6109.4134.8139170.8163201.1186245.5245.6303334365396

82.8102

98120.5109.5135139171162.8200185.6245.6218274246.7302.8286.2326.2

152174272

69.286.2

106.295.5

115.1111135125155155190185235303350395190235303350395

24314556.6749083.1

102.298

120.6109.4134.8139170.8163201.1186245.5245.6303334365396

82.8102

98120.5109.5135139171162.8200185.6245.6218274246.7302.8286.2326.2

152174272

69.286.2

106.295.5

115.1111 135 125155155190185235303350395190235303350395

24314556.6749083.1

102.298

120.6109.4134.8139170.8163201.1186245.5245.6303334365396

82.8102

98120.5109.5135139171162.8200185.6245.6218274246.7302.8286.2326.2

Unit: mm

SRG/SRN

SRG

SCR35456515A/V20A/V20LA/LV25C/R25LC/LR30C/R30LC/LR35C/R35LC/LR45C/R45LC/LR55C/R55LC/LR65LC/LV85LC100LC70LR85LR100LR130LR150LR8RM10RM12RM15A/B/R/YR20A/B/R/CA/CB/YR20LA/LB/LR/HA/HB25A/B/R/CA/CB/YR25LA/LB/LR/HA/HB30A/B/R/CA/CB/YR30LA/LB/LR/HA/HB35A/B/R/CA/CB/YR35LA/LB/LR/HA/HB45A/B/R/CA/CB/YR45LA/LB/LR/HA/HB55A/B/R/CA/CB/YR55LA/LB/LR/HA/HB65A/B/R/CA/CB/YR65LA/LB/LR/HA/HB85A/B/R/CA/CB/YR85LA/LB/LR/HA/HB100HA/HB/HR120HA/HB/HR150HA/HB/HR25XR/XA/XB25XLR/XLA/XLB30R/A/B30LR/LA/LB35R/A/B35LR/LA/LB45R/A/B45LR/LA/LB55R/A/B55LR/LA/LB65R/A/B65LR/LA/LB75R/A/B75LR/LA/LB85R/A/B85LR/LA/LB100R/A/B100LR/LA/LB


With QZLubricatorattached


With steeltape attached Number of rails used

on the same plane


Symbol for dustprevention

option

Symbol for radial clearanceNormal (no symbol), light preload (C1), medium preload (C0)


This model number indicates that a single-rail unit constitutes one set (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum).

Those models attached with the QZ Lubricator cannot have a grease nipple.Note

SHS25 LC 2 QZ KKHH C0 +1200L P Z -ⅡExample of model number coding

13

LaCS End plate

Grease nipple

：Reference surfaceK

H

Grease nipple mounting location for models SHS, SSR, SNR/SNS,SRG and NR/NRS

Table of Incremental Dimension of a Grease Nipple when LaCS is Attached

Unit: mm

Model No.Incremental

dimension withgrease nipple H

15C/LC15R/V/LV20C/LC20V/LV25C/LC25R/LR/V/LV30C/LC30R/LR/V/LV35C/LC35R/LR/V/LV45C/LC45R/LR/V/LV55C/LC55R/LR/V/LV65C/LC65V/LV15XVY/XWY15XTBY20XV/XW20XTB25XVY/XWY25XTBY30XW35XW25C/LC25R/LR30C/LC30R/LR35C/LC/CH/LCH35R/LR/RH/LRH45C/LC/CH/LCH45R/LR/RH/LRH55C/LC/CH/LCH55R/LR/RH/LRH65C/LC65R/LR35LC35LR45LC45LR55LC55LR65LC65LR

Nipple type

SHS

SSR

SNR/SNS

SRG

PB107PB107PB107PB107PB107PB107A-M6FA-M6FA-M6FA-M6FA-M6FA-M6FA-M6FA-M6FA-M6FA-M6FPB107PB107PB107PB107PB107PB107

PB1021BPB1021BPB1021BPB1021BPB1021BPB1021B

A-M6FA-M6FA-M6FA-M6FA-M6FA-M6F

A-PT1/8A-PT1/8A-M6FA-M6FA-M6FA-M6FA-M6FA-M6FA-M6FA-M6F

－4.7－4.5－4.7－7.4－7.4－7.7－7.4－6.94.4－4.6－4.5－55－4.9－4.5－7.8－7.9－7.7－

15.8－7.2－7.2－7.2－6.2


dimension withgrease nipple H

25X A/B/LA/LB25X R/LR30A/B/LA/LB30R/LR35A/B/LA/LB35R/LR45A/B/LA/LB45R/LR55A/B/LA/LB55R/LR65A/B/LA/LB65R/LR

Nipple type

NR/NRS

Grease nipple mounting location for models SHW, SRS and HSR

LaCS End plate

Grease nipple

E

－4.8－4.5－7.4－7.4－6.9－

15.3

PB1021BPB1021BPB1021BPB1021B

A-M6FA-M6FA-M6FA-M6FA-M6FA-M6F

A-PT1/8A-PT1/8


dimension withgrease nipple E

21CA/CR27CA/CR35CA/CR50CA/CR2515A/B/R/YR20A/B/R/CA/CB/YR20LA/LB/LR/HA/HB25A/B/R/CA/CB/YR25LA/LB/LR/HA/HB30A/B/R/CA/CB/YR30LA/LB/LR/HA/HB35A/B/R/CA/CB/YR35LA/LB/LR/HA/HB

Nipple type

SHW

SRS

HSR

4.210.71021

42.9

9.4

9

9

8

PB1021BB-M6FB-M6F

B-PT1/8PB1021BPB1021B

B-M6F

B-M6F

B-M6F

B-M6F

When desiring to attach a grease nipple in other than the above locations, contact THK.Those models attached with the QZ Lubricator cannot have a grease nipple. When desiring both the QZ Lubricator and a grease nipple to be attached,contact THK.With "ZZ" and "KK" types of model HSR15, a grease nipple is not available. Contact THK for details.

Note

Unit: mm Unit: mm

14

SNR45 LR 1 QZ ZZHH YY C1 +1200LWith Side Scraper attached

Example of model number coding

Note 1: The side scraper is not sold alone.Note 2: The side scraper can be attached with other various options including dust control parts and lubrication parts. Contact THK for

details.

Model No.Corner radius

r（max）Shoulder height for the LM rail

H1E

253035455565

11111.51.5

23.55.58

10.511

2.74.26.28.8

11.212.1

Unit: mm

SideScraper

Features●Minimizes the entry of foreign material from the side face of

the LM Guide in a harsh environment.● Provides a dust prevention effect in an inverted or wall-

mount orientation.

LM block

Side scraper separator

QZ Lubricator

End seal

Metal scraper

Intermediate plate

LaCS

End plate

Side scraper

Side scraper case

Schematic of side scraper installation (this example shows QZZZHHYY type)

Side face of the LM block

Foreign material

Foreign material

Foreign material

Inverted Wall mount

Route of the entry of foreign materialinto the LM block's side face

H1E r

r LaCS End plate

Grease nipple

：Reference surface

K

H

Table of Incremental Dimension of a Grease Nipple when Side Scraper is Attached

Model No.Incremental dimension

with grease nipple H

Nipple type

25LR/LC30LR/LC35LR/LC/LRH/LCH45LR/LC/LRH/LCH55LR/LC/LRH/LCH65LR/LC/LRH/LCH

SNR/SNSSNR/SNS

PB1021BPB1021B

A-M6FA-M6FA-M6F

A-PT1/8

4.54.55.45.45.48

Unit: mm

Height of the shoulder of the mounting surface and the corner radius after a side scraper is mounted Grease nipple mounting position

15

Light Sliding ResistanceContact Seal LiCS LiCS

LiCS is a contact seal with a low sliding resistance. It is effective in removing dust and the like from theraceway and retaining a lubricant such as grease. With its very low sliding resistance, LiCS achieves asmooth and stable motion.

FeaturesLight Sliding Resistance Contact Seal LiCS is a contact seal thatuses a low sliding resistance material for the seal andcontacts with the LM rail raceway. It is optimal for locationsrequiring a low sliding resistance such as semiconductor-related machines, inspection machines and OA equipment,which are used in favorable service conditions.

● Effective in removing dust or the like adhering to the LM rail raceway witha seal that contacts the raceway.

● Use of oil-impregnated, foamed synthetic rubber, which is high self-lubricating, achieves a low sliding resistance.

＊ LiCS model SSR is attached with a grease nipple as standard. For themounting location of the grease nipple and the incremental dimension withthe grease nipple attached, see page 16.

＊ LiCS models include types that also support other Caged Ball LMGuide models such as SHS. Contact THK for details.

Basic Specifications of LiCS● Service temperature range: -20℃ to +80℃● Resistance of LiCS: For seal resistance of LiCS, see

the table below.

LiCS

Note: Each value represents the sliding resistance of 2 LiCS units per LM block,one unit on each end, and excludes the sliding resistance of the blockand any other seals.

Maximum Seal Resistance of LiCS

Model No.

15X

20X

25X

30X

35X

15X

SSR

SRG

Resistance

1

1.1

1.6

1.6

2

0.7

Unit: N

Note: LiCS is not sold alone.

16

(Standard LM block length)

Overall LM block length with LiCS attached

L

Model No.

L


15XVY15XWY/XTBY20XV20XW/XTB25XVY25XWY/XTBY30XW35XW15A15V

GG PP

SSR

SRG

48.765.355.874.667.690.6106.7121.77777

48.765.355.874.667.690.6

106.7121.7

7777

40.356.947.766.5608397

110.96767

Unit: mm

Model No.Incremental dimension

with grease nipple Nipple type

15XVY15XWY/XTBY20XV20XW/XTB25XVY25XWY/XTBY30XW35XW15A15V

SSR

SRG

PB1021BPB1021B

B-M6FB-M6FB-M6FB-M6FB-M6FB-M6FPB107PB107

2.92.9999998ーー

Unit: mm

Grease-nipple mounting position for model SSR Grease-nipple mounting position for model SRG

ELiCS End plate

Grease nipple

K

H

LiCS End plate

Grease nipple

：Reference surface

E H

ーーーーーーーーー＊

4.5

Table of Incremental Dimension of a Grease Nipple when LiCS is Attached

Table of Incremental Dimension of a Grease Nipple when LiCS is Attached

＊ Since this model is a flanged type, the grease nipple does not protrude from the block end face.


With LiCSattached


Number of rails used onthe same plane


Symbol for radial clearanceNormal (no symbol), light preload(C1), medium preload (C0)


SSR20 XW 2 GG C1 +600L P -ⅡExample of model number coding

This model number indicates that a single-rail unit constitutes one set (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum).Note

17

Metal Cap Dedicated for LM Rail Mounting Holes

Mounting methodTo insert GC cap into a mounting hole, use a flat metalpiece like the one shown in the figure, and gradually drive themetal cap until its top is on the same level as the LM rail topface. When inserting GC cap, do not remove the LM blockfrom the LM rail.

GC Cap

GC cap is a metallic cap that plugs the LM rail mounting hole (article compliant with the RoHSDirectives). It prevents the entrance of foreign material and coolant from the LM rail top face (mounting hole)under harsh environments, and significantly increases the dust control performance of the LM Guide if usedwith a dust control seal.

Features● Eliminates the clearance between the mounting hole

(counterbore hole) and itselfSince GC Cap is driven into a mounting hole (counterborehole), it does not leave a clearance.

● Demonstrates a sealing effect over a long period due tosuperb resistance to wearIf a dust control seal or the like passes over the top face of theLM rail to which foreign material adheres, a downward force fromthe top of GC cap is generated.

Since the metal cap has a sufficient retention, it does not sinkeven in such a case.

GC CapLM rail

Magnified view

LM rail mounting bolt

GC Cap

LM rail

Eliminates the clearance

Does not sink

Adherence of foreign material

Dust control seal passes

Dust control seal

Metal piece

Plastic hammer

18

Note 1: The LM rail of an LM Guide model attached with GC cap is of special type.

Note 2: GC cap cannot be mounted on an LM rail made of stainless steel or provided with surface treatment.

Note 3: If using the product in a special environment such as vacuum, low temperature or high temperature, contact THK.

Note 4: GC cap is not sold alone. It is always provided in combination with LM Guide.

Note 5: The mouth of the LM rail mounting hole is not chamfered. Take care not to hurt your hand when attaching GC cap.

Note 6: After attaching GC cap, be sure to level and clean (wipe off) the tope face of the LM rail.

Note 7: If you desire a one-rail LM Guide model attached with GC cap, apply the following example of model number coding.

Applicable modelsGC Cap supports various models.

GC cap is capable of demonstrating a substantial effect under various environments.

If designating an LM Guide model attached with GC cap, observe the following example of model number coding.

Model No.LM rail

mountingbolt

LM Guide model number

SSR SR SNRSNS

NRNRS

SHSHSRHCR

SCRCSR

SHWHRW

SRGSRN SRW GSR HR NSR-

TBC

M5

M6

M8

M10 M12M14

M16

M22M24

2025Y30

35

———

—

——

2025Y30

35

45 55 —7085—

120

25

30

35

—45 55

65

85 —

25X

30

35

—45 55

65

85 —

20

25

3035—45 55

65

85 100

20

25

3035—45 —

65

——

—

35

50

60 ——

—

——

20

25

3035—45 55

65

85 100

—

—

—

7085

100

130

150—

20

25

30

35——

—

——

2042

—

255530653575 4085

—

50105

——

202530

40

50 70 —

—

——

GC5

GC6

GC8

GC10 GC12GC14

GC16

GC22GC24

Service environmentLM Guide

Use exampleAttached with standard C cap Attached with GC cap

Adverseenvironment

Amount offoreign

material -small

Metallic powder, spatterWood dust, coolant(environment where oil is lost)Metallic powder + coolantMetallic powder, spatterWood dust, coolant(environment where oil is lost)Metallic powder + coolant

○

○

○△

△

△

◎

◎

◎◎

◎

◎

Welding machine, robot Woodworking machine,

washing machine Lathe, machining centerWelding machine, robot Woodworking machine,

washing machine Lathe, machining center

Amount offoreign

material -large

◎：very effective ○：effective △：less effective

Dimensional tableUnit: mm

Model No. Outer diameter D Thickness H

GC5 9.86 2.5GC6 11.36 2.5GC8 14.36 3.5

GC10 17.86 3.5GC12 20.36 4.6GC14 23.36 5.0GC16 26.36 5.0GC22 35.36 5.0GC24 39.36 5.0

φD

H

Example:SNR45LR2QZKKHHC0+1200LPGCWith GC cap* Add the symbol “GC” at the end of the model number.

SNR45 LR 2 QZ KKHH C0 + 1200L P -ⅡGC

Symbol of number of rails used on the same plane (see Note 7)

Example of model number coding

Modelnumber

Type of LM block

With QZLubricator

Number of LM blocks per rail

Dust controloption symbol


With GC cap (see Note 7)

Radial clearance symbolNormal (no symbol)/light preload (C1)Medium preload (C0)

Accuracy symbolNormal grade (no symbol) / high-accuracy grade (H) / precision grade (P)Super precision grade (SP) / ultra-precision grade (UP)

Precautions on UseQZ Lubricator for the LM Guide

� Handling� Dropping or hitting this product may damage it. Take much care when handling it.� Do not block the air vent with grease or the like (see page 5).

� Service environment� The service temperature range for this product is between -10℃ and +50℃. Do not clean the product with an organic solvent or

white kerosene, or do not leave the product unpacked. When desiring to use the product out of the service temperature range,contact THK in advance.

� Use in a special environment� When desiring to use the product in a special environment, contact THK in advance.

� Precaution on selection� The stroke must be equal to or longer than the overall LM block length with QZ Lubricator attached.

� Rust prevention of the LM Guide� QZ Lubricator is a device designed to feed the required minimum amount of lubricant to the raceway, and therefore it does not have

a dust-prevention effect on the whole LM Guide. When using it in an adverse environment subject to a coolant or the like, werecommend applying grease or the like to the mounting base surface and the rail ends of the LM Guide as an anticorrosivemeasure.

Laminated Contact Scraper LaCS and Side Scraper for the LM Guide� Service environment

� The service temperature range is between -20℃ and +80℃. Do not clean the product with an organic solvent or white kerosene, ordo not leave the product unpacked.

� Impregnating oil� The purpose of the lubricant impregnated in the scraper is to increase the slidability of the scraper. For lubrication of the LM Guide,

attach a grease nipple on the end plate side face of QZ Lubricator or the LM block before feeding oil.� Functions

� Although these products have a dust prevention ability to remove foreign material and liquids, they require an end seal to sealgrease and oil.

� Design� When using these products, be sure to use the rail cap “GC” and a plate cover.

Light Sliding Resistance Contact Seal LiCS for the LM Guide� Service environment

� The service temperature range is between -20℃ and +80℃. Do not clean the product with an organic solvent or white kerosene, ordo not leave the product unpacked.

� Since the product contacts the LM rail raceway only, do not use it in a harsh environment.� Impregnating oil

� The purpose of the lubricant impregnated in LiCS is to increase the slidability of the seal. For lubrication of the LM Guide, attach agrease nipple on the end plate of the LM block before feeding oil.

GC Cap� Handling

� If you selected the GC Cap, take much care not to hurt your finger or hand when attaching the metal cap to the LM system since themouth of the LM rail mounting hole is sharp.

� When attaching the GC Cap, gradually drive the metal cap from the top surface of the LM rail using a flat metal piece until the metalcap top is on the same level as the top surface of the rail, and then smooth out the top surfaces of the rail and the GC Cap usingsandpaper, oil stone or the like so that the surfaces become even, before using the product.

Options for the LM Guide

● “LM GUIDE,” “ ,” and “ ,” are registered trademarks of THK CO., LTD.● The photo may differ slightly in appearance from the actual product.● The appearance and specifications of the product are subject to change without notice. Contact THK before placing an order.● Although great care has been taken in the production of this catalog, THK will not take any responsibility for damage resulting from typographical errors or omissions.● For the export of our products or technologies and for the sale for exports, THK in principle complies with the foreign exchange law and the Foreign Exchange

and Foreign Trade Control Law as well as other relevant laws.For export of THK products as single items, contact THK in advance. All rights reserved

HEAD OFFICE 3-11-6, NISHI-GOTANDA, SHINAGAWA-KU, TOKYO 141-8503 JAPAN INTERNATIONAL SALES DEPARTMENT PHONE:+81-3-5434-0351 FAX:+81-3-5434-0353

TAIWANTHK TAIWAN CO.,LTD.

TAIPEI HEAD OFFICEPhone:+886-2-2888-3818TAICHUNG OFFICEPhone:+886-4-2359-1505 TAINAN OFFICEPhone:+886-6-289-7668

KOREASEOUL REPRESENTATIVE OFFICE

Phone:+82-2-3468-4351SINGAPORETHK LM SYSTEM Pte. Ltd.

NORTH AMERICATHK America,Inc.

HEADQUARTERSPhone:+1-847-310-1111 Fax:+1-847-310-1271CHICAGO OFFICEPhone:+1-847-310-1111 Fax:+1-847-310-1182NEW YORK OFFICEPhone:+1-845-369-4035 Fax:+1-845-369-4909ATLANTA OFFICEPhone:+1-770-840-7990 Fax:+1-770-840-7897LOS ANGELES OFFICEPhone:+1-949-955-3145 Fax:+1-949-955-3149SAN FRANCISCO OFFICEPhone:+1-925-455-8948 Fax:+1-925-455-8965BOSTON OFFICEPhone:+1-781-575-1151 Fax:+1-781-575-9295DETROIT OFFICEPhone:+1-248-858-9330 Fax:+1-248-858-9455TORONTO OFFICEPhone:+1-905-820-7800 Fax:+1-905-820-7811

SOUTH AMERICATHK Brasil LTDA

Phone:+55-11-3767-0100 Fax:+55-11-3767-0101EUROPETHK GmbH

DÜSSELDORF OFFICEPhone:+49-2102-7425-0 Fax:+49-2102-7425-299

EUROPEAN HEADQUARTERSPhone:+49-2102-7425-0 Fax:+49-2102-7425-217

SHANGHAI OFFICEPhone:+86-21-6219-3000 Fax:+86-21-6219-9890BEIJING OFFICEPhone:+86-10-8441-7277 Fax:+86-10-6590-3557CHENGDU OFFICEPhone:+86-28-8526-8025 Fax:+86-28-8525-6357GUANGZHOU OFFICEPhone:+86-20-8523-8418 Fax:+86-20-3801-0456

CHINATHK (CHINA) CO.,LTD.

TURKEY OFFICEPhone:+90-216-362-4050 Fax:+90-216-569-7150PRAGUE OFFICEPhone:+420-2-41025-100 Fax:+420-2-41025-199

FRANKFURT OFFICEPhone:+49-2102-7425-650 Fax:+49-2102-7425-699STUTTGART OFFICEPhone:+49-7150-9199-0 Fax:+49-7150-9199-888MÜNCHEN OFFICEPhone:+49-8937-0616-0 Fax:+49-8937-0616-26U.K. OFFICEPhone:+44-1908-30-3050 Fax:+44-1908-30-3070ITALY MILANO OFFICEPhone:+39-039-284-2079 Fax:+39-039-284-2527ITALY BOLOGNA OFFICEPhone:+39-051-641-2211 Fax:+39-051-641-2230SWEDEN OFFICEPhone:+46-8-445-7630 Fax:+46-8-445-7639 AUSTRIA OFFICEPhone:+43-7229-51400 Fax:+43-7229-51400-79SPAIN OFFICEPhone:+34-93-652-5740 Fax:+34-93-652-5746

EINDHOVEN OFFICETHK Europe B.V.

THK France S.A.S.Phone:+33-4-3749-1400

Phone:+31-040-290-9500 Fax:+31-040-290-9599

Fax:+33-4-3749-1401

HEADQUARTERSPhone:+86-411-8733-7111 Fax:+86-411-8733-7000

THK (SHANGHAI) CO.,LTD.Phone:+86-21-6275-5280 Fax:+86-21-6219-9890

Fax:+886-2-2888-3819

Fax:+886-4-2359-1506

Fax:+886-6-289-7669

Fax:+82-2-3468-4353

Fax:+65-6884-5550INDIABANGALORE REPRESENTATIVE OFFICE

Phone:+91-80-2330-1524

Phone:+65-6884-5500

Fax:+91-80-2314-8226

Global site : http://www.thk.com/

©THK CO., LTD. 20090102 E7 Printed in Japan

options for the lm guide - thk technical support · for options for the lm guide not mentioned in...

Documents