opterna datasheets 3
DESCRIPTION
ÂTRANSCRIPT
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.comDSAH5rev1 1/3
TurnOpt™ Series 5000
The Opterna TurnOpt™ Series 5000 is a Fiber Distribution Hub specially designed for high density FDH topologies. Supporting up to 576 subscribers, the Series 5000 features a lightweight compact enclosure for pedestal mounting and Opterna’s exclusive rotating frame housed within. The Opterna TurnOpt™ Series 5000 is available in two standard configurations - stubbed pre-terminated with OSP feeder and distribution cables and stubless with additional compact partition loaded with splice trays for splicing the feeder and distribution cables. All Opterna TurnOpt™ FDH’s are fully loaded with pigtails, adapters and fiber management accessories. A wide variety of the universal Opterna factory pre-terminated MxN PLC splitters are available to use in the Series 5000 FDH.
Introduction
• Up to 576 subscribers in one cabinet • Factory loaded with all connectivity accessories which greatly reduces installation time and cost • Can house 18 plug-and-play PLC splitters • High density and small compact size dimension • The unique TurnOpt™ rotating frame gives full access to side and rear cable management • Smart slack management for the PLC splitter pre-terminated patch leads • Suitable for both Point-to-MultiPoint and Point-to-point architecture using PLC or pass-through modules • Parking adapters available for PLC outputs which are not yet connected • Stubbed and stubless versions available • Available in MTP/MPO terminated version usable with MTP/MPO terminated distribution cables• IP54 rated for outdoor/ indoor applications • Single door design for the stubbed version• Double door design for the stubless version with individual lock for the splicing partition • The outer cabinet can be completely replaced if needed without affecting service • Telcordia GR-3125 compliant
Features: TurnOpt™ Series 5000 High Density FDH
OSP Solutions
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.comDSAH5rev1 3/3
TurnOpt™ Series 5000
• All types of FTTX
• Point-to-Point fiber optic networks
• Outside plant for all types of telecom networks
• Multi Dwelling Units (MDU) with a large number of subscribers
Applications:
Specifications:
OSP Solutions
No Parameter Unit Stubbed Version Stubless Version1 Dimensions (H x W x D) mm 1314 x 510 x 400 1520 x 1023 x 4902 Mounting type Pedestal Pedestal
3 Configuration Pre-terminated feeder anddistribution side with 10mready to splice stubs
Pre-terminated feeder anddistribution side routed to splicetrays in additional partition
4 Feeder cable 24F or 48F N/A
5 Distribution cable 288F, 576F or 2x288F N/A
6 PLC splitter capacity Up to 18 modules 1:32 Up to 18 modules 1:32
7 Connector types SC/APC or SC/UPC SC/APC or SC/UPC
8 Insertion loss Max dB 0.30 0.30
9 Return loss Max dB 60.0 for APC, 55.0 for UPC 60.0 for APC, 55.0 for UPC
10 Standard compliances 50 for UPC 50
Cabinet GR-3125 GR-3125
Connectivity GR-326 GR-326
11 Color RAL-7032 RAL-7032
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.comDSAH5rev1 2/3
Visit: Opterna.com
AH 5
FeederFiber
Feeder CableConnection
Feeder CableType
Feeder Cable
Length
Distribution Side
Configuration
DistributionCable Type
DistributionStub Length
SplitterModule
SplitterType
ConnecterType
A 1A
closure
S Splice R Indoor /
Outdoor ribbon
A 10m S Splice trays
(Stubless)
1 Riser ribbon
stub
A 10m 00 No
Splitter
00 No
Splitter
SCA SC /
APC
B 1B
closure
R Patch Panel P Riser ribbon
stub
B 20m B Distribution
cable (stubbed)
2 Riser loose
tube stub
B 20m 01 1 Splitter 01 1X4 SCU SC /
UPC
0 None L Outdoor loose
tube stub
C 30m M MT
connectors
3 Loose tube
pigtails
C 30m 02 2 Splitter 02 1X8 XXX Custom
M Riser loose tube
stub
0 None 4 Ribbon
pigtails
0 None 03 3 Splitters
and so on
03 1X16
S Standard pigtail
(Splice)
5 MT
connectors
04 1X32
T Ribbon pigtail
(Splice)
0 No
distribution
6 Outdoor loose
tube stub
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
TurnOpt™ Series 5000OSP Solutions
Ordering Info:
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.comDSMECrev1 1/2
Universal Mechnical Splice
Opterna’s universal mechanical splice is an reliable, extremely easy-to-install and effective splice solution for all kinds of fiber optical architectures, including Telecommunications, FTTx, LAN and WAN networks.
The solution is indispensable when there is a need for quick repairs and in situations where fusion splicing is un-economical due to the low number of splicing needed in relation to distance, as is often the case in FTTx Networks.
Where mechanical splicing really comes to the fore is in situations where fusion splicing cannot be used due to the risk of explosion and other environmental dangers, including petrochemical plants and other areas where the risk of combustion is prominent.
Introduction
• Quick and easy to install, a splice takes less than 30 seconds once the fiber is stripped and cleaned
• No special tools required, installers only need a standard FO toolkit.
• One solution for 250 and 900μm, Singlemode and Multimode fiber
• Insertion losses are comparable to fusion splicing (typically less than 0.1dB)
• RoHS and UL-94-V0 compliant
• Environmentally friendly, adhesive free solution (V-groove technology)
• Reliable and easy to install due to a unique and accurate, fiber centering feature.
Features Universal Mechnical Splice
Central OfficeSolutions
screw cap jacket
lid
L
W
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.comDSMECrev1 2/2
Universal Mechnical Splice
• Optical communication systems
• All types of FTTH networks in residential, public and office buildings
• Urgent FO networks repairs
• Connecting FO cables in areas with high risk of explosion
Central OfficeSolutions
Applications:
Specifications:
Ordering info
Standard Unit MeasuresDimensions (LxWxD) mm 40x5x4
Cable type - Singlemode and multmode, 250/ 900μm
Insertion loss dB Typical ≤ 0.1, Maximum ≤ 0.3
Return loss dB >50
Splice method - V-groove adhesive free
Operating temperature °C -40°C to +80°C
Materials used - UL rated plastics and index matching gel
Packaging - 5 pieces/ pack
Product life - Over 25 years
Product part number Product descriptionOP-FC-MECHSPLICE Universal mechanical spice for 250/ 900μm
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
DSCAB1rev1 1/3
Visit: Opterna.com
Wall Mount Cabinet, Single Section
Opterna single section wall mount cabinet is suitable for applications where security and accessibility is required and floor space is at a premium. The cabinets are designed to hold multiple pieces of voice/data equipment comfortably. Ventilation is provided to allow active equipment to be installed, making it an ideal solution for small LAN’s, retail units and remote sites.
Opterna single section wall-mounted enclosures are designed to hold standard 19” rack mounted equipment and patch panels.
The cabinet features a lockable glass door, adjustable front profiles and removable entry plates at the top and bottom.
Introduction
• Constructed with rigid frames that can be fitted on a wall
• Adjustable mounting rails in the front and rear
• Top and bottom cable entry facility for easy cableinstallation
• Includes folded side doors with latch for ease of access
• Front section with glass door and lock
• Good ventilation and heat dispersion
Features Wall Mount Cabinet, Single Section
OSP Solutions
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
DSCAB1rev1 2/3
Visit: Opterna.com
Wall Mount Cabinet, Single Section
• Designed for installations that comply with the EN 50173-1,
EN 50174-1 & 2, ISO/IEC 11801, ANSI/TIA/EIA-568-C
Standard
Comply with mounting dimensions to IEC 297-3 and DIN - 41494 for all equipments
• IP 20
Material
• SPCC cold rolled steel
• Mounting profiles - 1.2mm
• Other elements - 1.0mm
• Door - Tempered glass
Loading Capacity
• 60 KG
Surface Finish
• Powder coated
Applications:
Technical Specification:
OSP Solutions
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
DSCAB1rev1 3/3
Visit: Opterna.comVisit: Opterna.com
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
Dimension:
Ordering Information:
OSP Solutions
Wall Mount Cabinet, Single Section
Part Number Description Capacity ‘U’ Width (mm) Depth (mm)
CAB-WMS-4-600-500 Wall Mount Cabinet, Single Section 4U 4 600 500
CAB-WMS-6-600-500 Wall Mount Cabinet, Single Section 6U 6 600 500
CAB-WMS-9-600-500 Wall Mount Cabinet, Single Section 9U 9 600 500
CAB-WMS-12-600-500 Wall Mount Cabinet, Single Section 12U 12 600 500
CAB-WMS-15-600-500 Wall Mount Cabinet, Single Section 15U 15 600 500
CAB-WMS-18-600-500 Wall Mount Cabinet, Single Section 18U 18 600 500
CAB-WMS-22-600-500 Wall Mount Cabinet, Single Section 22U 22 600 500
CAB-WMS-27-600-500 Wall Mount Cabinet, Single Section 27U 27 600 500
* For 600 depth cabinets replace 500 with 600* Includes two fans and one 6 Way PDU with universal sockets supporting BS plug or Schuko plugs
770.
05
770.
05
770.
05
770.
05
500
600
80 45
600
495
307
42
500
451
600600
500
40
40451 437 391
685.
05
466
620.
05
490
Ø13
40
FrontFront (without front door) Side Back
TOP
45
A A
A A
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.com
Fiber Distribution Box
The Fiber Distribution Box is suitable for various types of installations and can be used inside buildings or for telemetry applications. The FDB can be installed at every floor in the case of MDU and high rise building or can be installed in SDU to terminate the incoming fiber cable and fiber cable leading to the apartments.
The 24/48 port capacity fiber distribution box is designed to provide ample space for fiber optic cable routing, slack management and routing of pigtails and patch cords.
The product series are wall-mounted and easy to use and maintain. It is an integral component in the implementationof fiber networks for residential / commercial and utility segments.
The fiber distribution box are used in backbone, intermediate and horizontal cross connects, equipment room building entrance, telecommunications closets, IT rooms and customer premise applications.
Introduction
• Walled-mounted installation• Suitable for wall mounted in building corridor• Small size, light weight, high capacity, easy to splice and installation• Constructed of cold rolled steel and suitable for indoor application• Two lockable compartments with separate access system• Used for the distribution and connection of fibers, 4 inlets for fibers and 4 outlets for patch cords (One PG13.5 one PG21 at each four corner side of box)• For 24F distribution box, each compartment contains a 24 fiber splice tray with cover• Suitable for termination of 24F/48F incoming fiber cable in the left compartment and drop cables spliced or patch cord mechanical spliced at the right room• For 48F distribution box, each compartment with two 24F fiber splice tray with cover• Removable 12 fiber adaptor plate, suitable for SC/LC simplex or duplex or FC / ST simplex adaptors• Color: Gray• Mounting hardware kit included
Features Wall Mount Fiber Distribution Box
Central OfficeSolutions
DSFDBrev1 1/2
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.com
Fiber Distribution Box
Applications:
Specifications:
Ordering Info:
Central OfficeSolutions
DSFDBrev1 2/2
• FTTx
• Data Communication Network
• CCTV
Connector Type SC, FC, ST, LC
Door 2 with separate lock and key
Body Construction 1.2 mm Steel sheet
Powder Coated Paint Gray
Enclosure Dimensions 24/48 Port: 530 mm (W) x 355 mm (H) x 80 mm (D)
FDB
SC SC cutout SX 62.5/125 012 12 port
DC ST/FC cutout DX 50/125 024 24 port
048 48 port
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
DSCAB4rev1 1/3
Visit: Opterna.com
Wall Mount Cabinet Double Section
Opterna double section wall mount cabinet is suitable for applications where security and accessibility are required and floor space is at a premium.
The cabinets are designed to hold multiple pieces of voice/data equipment comfortably. Ventilation is provided to allow active equipment to be installed, making it an ideal solution for small LAN’s, retail units and remote sites.
Opterna double section wall-mounted enclosures are designed to hold standard 19” rack mounted equipment and patch panels.
The double section cabinet features a swing which allows easy back entry, a lockable glass door, adjustable front profiles and removable entry plates at the top and bottom.
Introduction
• Double section frame structure for easy back entry
• Constructed with rigid frames that can be fitted on a wall
• Adjustable mounting rails in the front and rear
• Top and bottom cable entry facility for easy cable installation
• Front section with glass door and lock
• Good ventilation and heat dispersion
• Back section depth - 100mm; swing out
• Removable side doors
Features Wall Mount Cabinet, Double Section
MDU Solutions
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
DSCAB4rev1 2/3
Visit: Opterna.com
Wall Mount Cabinet Double Section
• Designed for installations that comply with the
EN 50173-1, EN 50174-1 & 2, ISO/IEC 11801,ANSI/TIA/EIA-568-C
Standard
• Comply with mounting dimensions to IEC 297-3 and DIN - 41494 for all equipments
• IP 20
Material
• SPCC cold rolled steel
• Mounting profiles - 1.2mm
• Other elements - 1.0mm
• Door - Tempered glass
Loading Capacity
• 60 KG
Surface Finish
• Powder coated
Applications:
Technical Specification:
MDU Solutions
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
DSCAB4rev1 3/3
Visit: Opterna.comVisit: Opterna.com
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
Dimension:
Ordering Information:
MDU Solutions
Wall Mount Cabinet Double Section
Part Number Description Capacity ‘U’ Width (mm) Depth (mm)
CAB-WMD-4-600-600 Wall Mount Cabinet, Double Section 4U 4 600 500 + 100
CAB-WMD-6-600-600 Wall Mount Cabinets, Double Section 6U 6 600 500 + 100
CAB-WMD-9-600-600 Wall Mount Cabinets, Double Section 9U 9 600 500 + 100
CAB-WMD-12-600-600 Wall Mount Cabinets, Double Section 12U 12 600 500 + 100
CAB-WMD-15-600-600 Wall Mount Cabinets, Double Section 15U 15 600 500 + 100
CAB-WMD-18-600-600 Wall Mount Cabinets, Double Section 18U 18 600 500 + 100
CAB-WMD-22-600-600 Wall Mount Cabinets, Double Section 22U 22 600 500 + 100
CAB-WMD-27-600-600 Wall Mount Cabinets, Double Section 27U 27 600 500 + 100
* For 500 depth cabinets replace 600 with 500, total depth will be 400 + 100* Includes two fans and one 6 Way PDU with universal sockets supporting BS plug or Schuko plugs
770.
05
450465600
437600
685.
0577
0.05
100
50060
0
450492600
100
500
600
359.5600
478.5
2234056
530
669.
6568
6.25
40
FrontFront (without front door)TO
PSide Back
A A
A A
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.com
Floor Standing Steel Cabinets
Opterna floor standing steel cabinets are designed with precise craftmanship to meet the ever increasing demands of networking equipment located within a cabinet.
To meet the diverse and ever changing demands of structured cabling systems and active equipment, the cabinets are engineered with strength and robustness.
Introduction
• Steel frame structure
• Vented top cover with cable entry provision and entry plate
• Fan housing unit
• Bottom cover with cable entry provision and entry plate
• Side panels with slam latches and locking facility
• Front tempered glass door with lock
• Optional arc or flat 71% perforated front door with lock
• Rear steel door with lock and 71% perforation for airflow
• Side mounting angles
• 19-inch equipment mounting angles
• 800 mm wide cabinets are available with spacer and vertical patchcord management
• Leveling feet and heavy duty castors
• Optional plinth for under base cable entry
Features Floor Standing Steel Cabinets
MDU Solutions
DSCAB5rev1 1/5
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.com
Floor Standing Steel Cabinets
• Designed for installations that comply with the EN 50173-1, EN 50174-1 & 2, ISO/IEC 11801,
ANSI/TIA/EIA-568-C
Standard:• Comply with mounting dimensions to IEC 297-3 and DIN - 41494 for all equipments• IP 20
Material:• SPCC cold rolled steel• Mounting profiles - 2.0 mm, Mounting angles - 1.5mm, Other elements - 1.2mm
Loading Capacity:• 600 KG
Surface Finish:• Powder coated RAL 9017 Black fine texture finish
Package:• Available as flat packed or fully assembled• Default components included are: • 6 Way PDU, universal sockets supports BS plug or Schuko plugs • 4 Fans • Leveling Feet • Heavy Duty Castors
Applications:
Technical Specification:
MDU Solutions
DSCAB5rev1 2/5
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.comVisit: Opterna.com
MDU Solutions
Floor Standing Steel Cabinets
Ordering Info:
Part Number Description Capacity‘U’
Height(H)
in mm
Width(W)
in mm
Depth(D)
in mm
CAB-FMS-18-600-600 Floor Standing Cabinet, Steel Frame, 18U, 600mm (W) x 600mm (D) 18 988.2 600 600
CAB-FMS-18-600-800 Floor Standing Cabinet, Steel Frame, 18U, 600mm (W) x 800mm (D) 18 988.2 600 800
CAB-FMS-18-600-1000 Floor Standing Cabinet, Steel Frame, 18U, 600mm (W) x 1000mm (D) 18 988.2 600 1000
CAB-FMS-18-600-1200 Floor Standing Cabinet, Steel Frame, 18U, 600mm (W) x 1200mm (D) 18 988.2 600 1200
CAB-FMS-18-800-600 Floor Standing Cabinet, Steel Frame, 18U, 800mm (W) x 600mm (D) 18 988.2 800 600
CAB-FMS-18-800-800 Floor Standing Cabinet, Steel Frame, 18U, 800mm (W) x 800mm (D) 18 988.2 800 800
CAB-FMS-18-800-1000 Floor Standing Cabinet, Steel Frame, 18U, 800mm (W) x 1000mm (D) 18 988.2 800 1000
CAB-FMS-18-800-1200 Floor Standing Cabinet, Steel Frame, 18U, 800mm (W) x1200mm (D) 18 988.2 800 1200
CAB-FMS-22-600-600 Floor Standing Cabinet, Steel Frame, 22U, 600mm (W) x 600mm (D) 22 1166 600 600
CAB-FMS-22-600-800 Floor Standing Cabinet, Steel Frame, 22U, 600mm (W) x 800mm (D) 22 1166 600 800
CAB-FMS-22-600-1000 Floor Standing Cabinet, Steel Frame, 22U, 600mm (W) x 1000mm (D) 22 1166 600 1000
CAB-FMS-22-600-1200 Floor Standing Cabinet, Steel Frame, 22U, 600mm (W) x 1200mm (D) 22 1166 600 1200
CAB-FMS-22-800-600 Floor Standing Cabinet, Steel Frame, 22U, 800mm (W) x 600mm (D) 22 1166 800 600
CAB-FMS-22-800-800 Floor Standing Cabinet, Steel Frame, 22U, 800mm (W) x 800mm (D) 22 1166 800 800
CAB-FMS-22-800-1000 Floor Standing Cabinet, Steel Frame, 22U, 800mm (W) x 1000mm (D) 22 1166 800 1000
CAB-FMS-22-800-1200 Floor Standing Cabinet, Steel Frame, 22U, 800mm (W) x1200mm (D) 22 1166 800 1200
CAB-FMS-24-600-600 Floor Standing Cabinet, Steel Frame, 24U, 600mm (W) x 600mm (D) 24 1254.9 600 600
CAB-FMS-24-600-800 Floor Standing Cabinet, Steel Frame, 24U, 600mm (W) x 800mm (D) 24 1254.9 600 800
CAB-FMS-24-600-1000 Floor Standing Cabinet, Steel Frame, 24U, 600mm (W) x 1000mm (D) 24 1254.9 600 1000
CAB-FMS-24-600-1200 Floor Standing Cabinet, Steel Frame, 24U, 600mm (W) x 1200mm (D) 24 1254.9 600 1200
CAB-FMS-24-800-600 Floor Standing Cabinet, Steel Frame, 24U, 800mm (W) x 600mm (D) 24 1254.9 800 600
CAB-FMS-24-800-800 Floor Standing Cabinet, Steel Frame, 24U, 800mm (W) x 800mm (D) 24 1254.9 800 800
CAB-FMS-24-800-1000 Floor Mount Cabinet, Steel Frame, 47U, 800mm(W) x 1000mm(D) 24 1254.9 800 1000
CAB-FMS-24-800-1200 Floor Standing Cabinet, Steel Frame, 24U, 800mm (W) x1200mm (D) 24 1254.9 800 1200
CAB-FMS-27-600-600 Floor Standing Cabinet, Steel Frame, 27U, 600mm (W) x 600mm (D) 27 1388.25 600 600
CAB-FMS-27-600-800 Floor Standing Cabinet, Steel Frame, 27U, 600mm (W) x 800mm (D) 27 1388.25 600 800
CAB-FMS-27-600-1000 Floor Standing Cabinet, Steel Frame, 27U, 600mm (W) x 1000mm (D) 27 1388.25 600 1000
CAB-FMS-27-600-1200 Floor Standing Cabinet, Steel Frame, 27U, 600mm (W) x 1200mm (D) 27 1388.25 600 1200
CAB-FMS-27-800-600 Floor Standing Cabinet, Steel Frame, 27U, 800mm (W) x 600mm (D) 27 1388.25 800 600
CAB-FMS-27-800-800 Floor Standing Cabinet, Steel Frame, 27U, 800mm (W) x 800mm (D) 27 1388.25 800 800
CAB-FMS-27-800-1000 Floor Standing Cabinet, Steel Frame, 27U, 800mm (W) x 1000mm (D) 27 1388.25 800 1000
CAB-FMS-27-800-1200 Floor Standing Cabinet, Steel Frame, 27U, 800mm (W) x1200mm (D) 27 1388.25 800 1200
DSCAB5rev1 3/5
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.com
Part Number Description Capacity‘U’
Height(H)
in mm
Width(W)
in mm
Depth(D)
in mmCAB-FMS-32-600-600 Floor Standing Cabinet, Steel Frame, 32U, 600mm (W) x 600mm (D) 32 1610.5 600 600
CAB-FMS-32-600-800 Floor Standing Cabinet, Steel Frame, 32U, 600mm (W) x 800mm (D) 32 1610.5 600 800
CAB-FMS-32-600-1000 Floor Standing Cabinet, Steel Frame, 32U, 600mm (W) x 1000mm (D) 32 1610.5 600 1000
CAB-FMS-32-600-1200 Floor Standing Cabinet, Steel Frame, 32U, 600mm (W) x 1200mm (D) 32 1610.5 600 1200
CAB-FMS-32-800-600 Floor Standing Cabinet, Steel Frame, 32U, 800mm (W) x 600mm (D) 32 1610.5 800 600
CAB-FMS-32-800-800 Floor Standing Cabinet, Steel Frame, 32U, 800mm (W) x 800mm (D) 32 1610.5 800 800
CAB-FMS-32-800-1000 Floor Standing Cabinet, Steel Frame, 32U, 800mm (W) x 1000mm (D) 32 1610.5 800 1000
CAB-FMS-32-800-1200 Floor Standing Cabinet, Steel Frame, 32U, 800mm (W) x1200mm (D) 32 1610.5 800 1200
CAB-FMS-37-600-600 Floor Standing Cabinet, Steel Frame, 37U, 600mm (W) x 600mm (D) 37 1832.75 600 600
CAB-FMS-37-600-800 Floor Standing Cabinet, Steel Frame, 37U, 600mm (W) x 800mm (D) 37 1832.75 600 800
CAB-FMS-37-600-1000 Floor Standing Cabinet, Steel Frame, 37U, 600mm (W) x 1000mm (D) 37 1832.75 600 1000
CAB-FMS-37-600-1200 Floor Standing Cabinet, Steel Frame, 37U, 600mm (W) x 1200mm (D) 37 1832.75 600 1200
CAB-FMS-37-800-600 Floor Standing Cabinet, Steel Frame, 37U, 800mm (W) x 600mm (D) 37 1832.75 800 600
CAB-FMS-37-800-800 Floor Standing Cabinet, Steel Frame, 37U, 800mm (W) x 800mm (D) 37 1832.75 800 800
CAB-FMS-37-800-1000 Floor Standing Cabinet, Steel Frame, 37U, 800mm (W) x 1000mm (D) 37 1832.75 800 1000
CAB-FMS-37-800-1200 Floor Standing Cabinet, Steel Frame, 37U, 800mm (W) x1200mm (D) 37 1832.75 800 1200
CAB-FMS-42-600-600 Floor Standing Cabinet, Steel Frame, 42U, 600mm (W) x 600mm (D) 42 2055 600 600
CAB-FMS-42-600-800 Floor Standing Cabinet, Steel Frame, 42U, 600mm (W) x 800mm (D) 42 2055 600 800
CAB-FMS-42-600-1000 Floor Standing Cabinet, Steel Frame, 42U, 600mm (W) x 1000mm (D) 42 2055 600 1000
CAB-FMS-42-600-1200 Floor Standing Cabinet, Steel Frame, 42U, 600mm (W) x 1200mm (D) 42 2055 600 1200
CAB-FMS-42-800-600 Floor Standing Cabinet, Steel Frame, 42U, 800mm (W) x 600mm (D) 42 2055 800 600
CAB-FMS-42-800-800 Floor Standing Cabinet, Steel Frame, 42U, 800mm (W) x 800mm (D) 42 2055 800 800
CAB-FMS-42-800-1000 Floor Standing Cabinet, Steel Frame, 42U, 800mm (W) x 1000mm (D) 42 2055 800 1000
CAB-FMS-42-800-1200 Floor Standing Cabinet, Steel Frame, 42U, 800mm (W) x1200mm (D) 42 2055 800 1200
CAB-FMS-45-600-600 Floor Standing Cabinet, Steel Frame, 45U, 600mm (W) x 600mm (D) 45 2188.35 600 600
CAB-FMS-45-600-800 Floor Standing Cabinet, Steel Frame, 45U, 600mm (W) x 800mm (D) 45 2188.35 600 800
CAB-FMS-45-600-1000 Floor Standing Cabinet, Steel Frame, 45U, 600mm (W) x 1000mm (D) 45 2188.35 600 1000
CAB-FMS-45-600-1200 Floor Standing Cabinet, Steel Frame, 45U, 600mm (W) x 1200mm (D) 45 2188.35 600 1200
CAB-FMS-45-800-600 Floor Standing Cabinet, Steel Frame, 45U, 800mm (W) x 600mm (D) 45 2188.35 800 600
CAB-FMS-45-800-800 Floor Standing Cabinet, Steel Frame, 45U, 800mm (W) x 800mm (D) 45 2188.35 800 800
CAB-FMS-45-800-1000 Floor Standing Cabinet, Steel Frame, 45U, 800mm (W) x 1000mm (D) 45 2188.35 800 1000
CAB-FMS-45-800-1200 Floor Standing Cabinet, Steel Frame, 45U, 800mm (W) x1200mm (D) 45 2188.35 800 1200
Floor Standing Steel CabinetsMDU Solutions
DSCAB5rev1 4/5
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.com Visit: Opterna.com
Part Number Description Capacity‘U’
Height(H)
in mm
Width(W)
in mm
Depth(D)
in mmCAB-FMS-47-600-600 Floor Standing Cabinet, Steel Frame, 47U, 600mm (W) x 600mm (D) 47 2277.25 600 600
CAB-FMS-47-600-800 Floor Standing Cabinet, Steel Frame, 47U, 600mm (W) x 800mm (D) 47 2277.25 600 800
CAB-FMS-47-600-1000 Floor Standing Cabinet, Steel Frame, 47U, 600mm (W) x 1000mm (D) 47 2277.25 600 1000
CAB-FMS-47-600-1200 Floor Standing Cabinet, Steel Frame, 47U, 600mm (W) x 1200mm (D) 47 2277.25 600 1200
CAB-FMS-47-800-600 Floor Standing Cabinet, Steel Frame, 47U, 800mm (W) x 600mm (D) 47 2277.25 800 600
CAB-FMS-47-800-800 Floor Standing Cabinet, Steel Frame, 47U, 800mm (W) x 800mm (D) 47 2277.25 800 800
CAB-FMS-47-800-1000 Floor Standing Cabinet, Steel Frame, 47U, 800mm (W) x 1000mm (D) 47 2277.25 800 1000
CAB-FMS-47-800-1200 Floor Standing Cabinet, Steel Frame, 47U, 800mm (W) x1200mm (D) 47 2277.25 800 1200
MDU Solutions
Floor Standing Steel Cabinets
Part Number Description Depth(D)
in mmCAB-AC-CS-350-1U 1U Cantilever shelf, 350 depth 350
CAB-AC-CS-350-2U 2U Cantilever shelf, 350 depth 350
CAB-AC-FS-450 Fixed shelf, 450 mm depth, for 600 depth cabinets 450
CAB-AC-FS-550 Fixed shelf, 550 mm depth, for 800 depth cabinets 550
CAB-AC-FS-750 Fixed shelf, 750 mm depth, for 1000 depth cabinets 750
CAB-AC-FS-950 Fixed shelf, 950 mm depth, for 1200 depth cabinets 950
CAB-AC-SS-450 Sliding shelf, 450 mm Depth, for 600 depth cabinets 450
CAB-AC-SS-550 Sliding shelf, 550 mm Depth, for 800 depth cabinets 550
CAB-AC-SS-750 Sliding shelf, 750 mm Depth, for 1000 depth cabinets 750
CAB-AC-SS-950 Sliding shelf, 950 mm Depth, for 1200 depth cabinets 950
CAB-AC-KB Sliding Keyboard Shelf -
CAB-AC-FT2 Fan Tray, 1U, 2 Fan Position -
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
Default front door is 7000 series and rear door 7002 series, for other door configuration use the below mentioned codes.
Door identification series:Glass door : 7000Arc vented door : 7001Flat vented door : 7002Twin flat vented door : 7003
DSCAB5rev1 5/5
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.comDSQACrev1 1/3
Quick Assembly Connectors
Opterna Quick Assembly connectors, also known as “no polish connectors” are designed to provide fast on-site installation. Field installation of 250 or 900um fiber, 2.0, 3.0mm or flat cable is achieved without the need for power or advanced polishing techniques. The pre-assembled connector can be installed in under a minute and re-used several times. It provides a reliable and durable optical connection and is especially suitable for advanced fiber optic systems requiring exceptional stability and low back reflections.
Introduction
• SC and LC interfaces
• Available in UPC and APC end face finish
• Singlemode and multimode
• Fast installation in less than a minute
• Use with 250 or 900um fiber, 2.0, 3.0mm or flat cable
• Re-usable
• Low insertion loss
Features Quick Assembly Connectors
Fiber Interconnect & Passives
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.comDSQACrev1 2/3
Quick Assembly Connectors
• FTTH/x networks
• Optical communication systems
• Local area networks
• Optical cable interconnect
• Telecoms
Fiber Interconnect & Passives
Applications:
Specifications:
dB Unit SC connector LC connectorConnection Type - V-groove technology
Ferule Polishing Type - PC/UPC/APC PC/UPC/APC
Fiber Type - Single and Multi mode
Cable Diameter mm Round - 900 um, 2.0mm, 3.0mm, flat cable
Insertion Loss dB Typical 0.3 Typical 0.1
Return Loss dB UPC-Typical 50 UPC-Typical 50
APC-Typical 55 APC-Typical 55
PC (MM)-Typical 20
Operating Temperature C ° -45 to +85 -45 to +75
Americas:(703) [email protected]
Europe:+44(0)2031 301 [email protected]
Middle East:+971 4 299 [email protected]
Asia Pacific:+91(0) 484 2104 [email protected]
OpternaROpternaR
Visit: Opterna.comDSQACrev1 3/3
Visit: Opterna.com
QAC
ConnectorType
Grade Fiber Type Cable Type Color
LC LC P PC 7A2 SM G657 A2 09 0.9mm BL Blue
SC SC U UPC OS2 SMG652D 20 2.0mm GN Green
A APC OM1 MM 62.5/ 125 30 3.0mm BG Beige
OM4 MM 50/ 125 FC Flat Cable
UN Universal for 0.9, 2.0, 3.0mm and flat cable
Size & Dimensions:
Ordering Info:
Quick Assembly ConnectorsFiber Interconnect
& Passives
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
Fig 1: SC Quick Assembly Connector Fig 2: LC Quick Assembly Connector