onedesign foamy
DESCRIPTION
rc plane for foamyTRANSCRIPT
-
TYPICAL HINGE
Dubro hinge tape
5mm Cellfoam88 flying surface 5mm Cellfoam88 control surface
Specifications: Wing Span - 32.0" Overall length - 27.7" Wing Area - 230 square inches Weight - 9-12 ounces
Enlarge opening 1" to fit stabilizer assembly in place.Then fill with scrap Cellfoam88
One Design Materials:
Construction: Two sheets of 5mm Cellfoam88 Fuselage: 5mm Cellfoam88 Motor stick: Midwest #5723, .196" OD. Carbon Tube - 3/8" x 0.75" square stock for motor mount Wing: 5mm CellFoam88 Spars: Midwest #5723, .196" OD. Carbon Tube Tail Surfaces: 5mm CellFoam88Tail Skid (options): Dubro #854, Micro Tail Wheel Bracket or Dubro # 12MTW, " Tail WheelHinge Material: Dubro # 916, Hinge Tape - one rollControl Horns & Accessories: 1/16" PlywoodPushrods: 1-24" length, Midwest 0.05" Carbon Fiber RodPushrod Linkage: K&S .031" x 36" Music WireLanding Gear: K&S .06"x14" Music WireMain Wheels: Dubro # 150MW, 1 " Mini Lite WheelsServos: JR 241 Sub Micro (JRSPORT SM15)Receiver: JR 610 UL**Speed Control: Castle Creations, Phoenix 10Motor (options): Maxx Products (MPI EPU37066) 6.6:1 gearing or Himax- HA2015-4100 Brushless w/Gear Drive 6.6:1 or Himax- HC2816-0850 Out Runner BrushlessSpinner GWS, # GW/SPN008AProp: 11x7SF 12x6SF APCBattery : 2 to 3 Cell Li-Poly 1200 mAh (10C)
0.06 K&S Music Wire typical
Bend wire 90 degrees forward
1/8" Light Plywood Collars
MAIN GEAR
RIGHT FUSELAGE SIDE5mm Cellfoam88
LEFT FUSELAGE SIDE5mm Cellfoam88
HO
RIZ
ON
TAL
STA
BIL
IZE
R5m
m C
ellfo
am88
VERTICAL STABILIZER5mm Cellfoam88
ESCREC.
BATTERY
ELE.AIL.
RUD.FUSELAGE
5mm Cellfoam88
1/8" Light PlywoodMotor Plate
OPTIONAL OUTRUNNER MOTOR INSTALLATION
Hinge Line
MOTOR AREACut to suit
.196" OD. Carbon Tube Motor Stick3/8" x 0.75" square wood stock
for motor mount
1/16" Plywood Landing Gear Reinforcement Plate
Right
Left
Notch for Control Horn
ON
E P
IEC
E W
ING
5mm
Cel
lfoam
88.1
96" O
D. C
arbo
n Tu
be S
par
LEFT WHEEL PANT5mm Cellfoam88
RIGHT WHEEL PANT
5mm Cellfoam88
GEAR LEG COVERS5mm Cellfoam88
GWS (SPN008A) 40mm Spinner for 3mm motor shaft
NOTES ABOUT MAKING TEMPLATESCreate templates using the outside edge of the line as a guide.Use the center of the line as a guide for cutouts and hinge lines.
1 2 3 4 5
1" Scale: Check drawings after printing
www.midwestproducts.com
AIL.1
AIL.2
ASSEMBLY CROSSECTIONTo illustrate layering of material
Designed and Drawn By Michael Ramsey
Fuselage Side Guides
Center of Gravity
Tail wheel assemblyK&S .047 Music wire
COPIES OF THIS DRAWING MAY BE MADE FOR PERSONAL USE ONLY