Operator's ManualPlease read these instructionscarefully and make sure youunderstand them before using themachine.

Svenska – 31

Sve-5 225/232/235 Bruk 97-11-25, 08.4631

English – 1

Operator’s manual forFR 2111, FR 2113 A, FR 2113 MA, FR 2116 MA

TABLE OF CONTENTS

Introduction ......................................................... 2Driving and transport on public roads .............. 2Towing .............................................................. 2Use ................................................................... 2Serial number ................................................... 3

Explanation of symbols ...................................... 4Safety instructions .............................................. 5

General use ..................................................... 5Driving on slopes ............................................. 7Children ............................................................ 8Maintenance .................................................... 8Transport ........................................................ 10

Presentation ...................................................... 11Placement of controls .................................... 11Throttle/Choke control FR 2111 ..................... 12Clutch pedal FR 2111 ..................................... 12Brake pedal/Parking brake FR 2111 .............. 12Throttle/Choke control FR 2113, FR 2116...... 13Accelerator FR 2113, FR 2116 ....................... 13Parking brake FR 2113, FR 2116 ................... 13Mowing deck .................................................. 14Lifting lever for the mowing deck ................... 14Lever to adjust the cutting height ................... 15Seat ................................................................ 15Refuelling ....................................................... 15

Driving ................................................................ 16Before starting ................................................ 16Starting the engine ......................................... 16Driving the Rider ............................................ 18Mowing tips .................................................... 19Stopping the engine ....................................... 20Clutch control FR 2113, FR 2116 ................... 20

Maintenance ...................................................... 21Maintenance schedule ................................... 21Dismantling the Rider covers ......................... 22Checking and adjusting the steering wires .... 24Checking and adjusting the brake .................. 25Adjusting the throttle cable ............................. 26

IMPORTANT INFORMATION

Read carefully through the Operator’s manual so that you know how to use and maintain theRider before you use it.

For service measures other than those described in this manual, please contact an authoriseddealer that provides parts and service.

Replacing the fuel filter .................................. 26Replacing the air filter .................................... 27Checking the fuel pump’s air filter .................. 28Checking the acid level in the battery ............ 28Ignition system ............................................... 28Checking the safety system FR 2111 ............. 29Checking the safety system FR 2113,FR 2116.......................................................... 30Main fuse ....................................................... 31Checking the tyres’ air pressure ..................... 31Checking the engine’s cooling air intake. ....... 31Checking and adjusting the mowing deck’sground pressure ............................................. 32Checking the parallelism of the mowing deck 32Adjusting the parallelism of the mowingdeck FR 2111, FR 2113 MA ........................... 33Adjusting the parallelism of the mowingdeck FR 2116 MA........................................... 34Removing the mulching plug .......................... 34Service position for the mowing deck ............ 35Inspecting the blades ..................................... 38Replacing the shear pin ................................. 38

Lubrication......................................................... 39Checking the engine’s oil level ....................... 39Replacing the engine oil ................................. 39Checking the oil level in the transmission ...... 40Lubricating the belt adjuster ........................... 40General lubrication ......................................... 40Lubricating the front wheel bearings .............. 41

Trouble shooting chart ..................................... 42Storage ............................................................... 43

Winter storage ................................................ 43Cover ............................................................. 43Service ........................................................... 43

Technical data ................................................... 44EU declaration of conformity ........................... 47Service journal .................................................. 48

2– English

Congratulations

Thank you for purchasing a Front Rider. Front Riders have been designed according to a unique conceptwith a front mounted mowing deck and patented rear wheel steering. The machine is built to give maximumefficiency even in small and confined areas. Collected controls and a hydrostatic transmission controlled bypedals(some models) also contribute to the machine’s performance.

This operator’s manual is a valuable document. Following the instructions (use, service, maintenance, etc.)can considerably increase the life span of your machine and even increase its resale value.

When you sell your machine, make sure to give the operator’s manual to the new owner.

Driving and transport on public roads

Check applicable road traffic regulations before driving and transport on public roads. You should always useapproved fasteners during transport and ensure the machine is secured correctly.

Towing

Your machine is equipped with a hydrostatic transmission and, if necessary, you should only tow the ma-chine over short distances and at a low speed, otherwise there is a risk of damaging the transmission.

Use

This machine has been designed solely to mow grass on lawns and other open and level ground surfaceswithout obstacles such as stones, stumps and the like. The machine can also be used for other tasks whenequipped with special accessories supplied by the manufacturer and for which the operator’s manual hasbeen supplied in connection with delivery. All other types of use are incorrect. The manufacturer’sinstructions with regard to driving, maintenance and repair must be followed precisely.

The machine may only be operated, maintained and repaired by persons that are fully conversant with themachine’s special characteristics and safety instructions.

Accident prevention regulations, other general safety regulations, occupational safety rules and trafficregulations must be observed.

Unauthorized modifications to the design of the machine may absolve the manufacturer from liability for anyresulting personal injury or damage to property.

INTRODUCTION

English – 3

Good service

Jonsered’s products are sold all over the world and only in specialised retail trade with complete service.This ensures that you as a customer receive only the best support and service. Before the machine isdelivered it undergoes inspection and is adjusted by your dealer.

When you need spare parts or support in questions about service, warranty issues, etc., please consult thefollowing professional:

This operator’s manual belongs to machinewith serial number:

INTRODUCTION

Serial number

The serial number can be found on the printed plate attached to the front, left-hand side under the seat.Stated on the plate, from the top are:

• The machine’s type designation.

• The manufacturer’s type number.

• The machine’s serial number.

Please state the type designation and serial number when ordering spare parts.

The engine number is punched on a plate that is riveted to the fan cover. The plate states:

• Model.

• Type.

• Code.

Please state these when ordering spare parts.

The transmission’s serial number on hydrostat machines is stated on the barcode decal located on the frontof the housing on the left-hand drive shaft:

• Type designation is stated above the barcode and starts with the letter K.

• The serial number is stated above the barcode and has the prefix s/n.

• The manufacturer’s type number is stated under the barcode and has the prefix p/n.

Please state the type designation and serial number when ordering spare parts.

Engine Transmission

4– English

NR

These symbols can be found on the Rider and in the operator’s manual.Study them carefully so you understand their significance.

Read the operator’s manual.

Reverse Neutral Fast Slow Engine off Battery Choke Fuel

Oil level Cutting height Reversing Forward Ignition Hydrostatic free wheeling

EXPLANATION OF SYMBOLS

Never use the Rider if persons, especiallychildren or pets, are in the immediate vicinity

Never carry passengers on the Rideror on its tools

Starting instruction

Read the operator’s manual

Check the engine oil level

Check the oil level in the hydrostat

Lift up the mowing deck

Put the gear shift lever/hydrostatpedals in the neutral position

Brake

Use the choke if the engine is cold

Starting the engine

Disengage the parking brakebefore driving

Drive very slowlywithout the mowing

deck

Do not insert your hands orfeet under the cover when

the engine is running

Accelerator pedal forward

Neutral position

Accelerator pedal reversing

Switch off the engine and removethe ignition cable before carryingout repairs or maintenance

CE conformitymarking

Warning!Rotating blades

Warning! Risk ofthe Rider overturning

Never drive directly acrossa slope

Noise emissions to surroundingsin accordance with the EuropeanUnion’s directive. The machine’semissions are set out in thechapter TECHNICAL DATA andon the decal.

Use hearing protection Clutch in Clutch out Parking brake Brake Clutch Warning

English – 5

8010-047

6003-002

8010-052

Safety instructionsThese instructions are for your safety. Read them carefully.

General use

• Read all the instructions in this operator’smanual and on the machine before you start it.Ensure you understand them and then observethem.

• Learn how to use the machine and its controlssafely and learn to how to stop quickly. Alsolearn to recognize the safety decals.

• Only allow the machine to be used by adultswho are familiar with its use.

• Make sure nobody else is in the vicinity of themachine when you start the engine, engage thedrive or drive off.

• Make sure animals and people maintain a safedistance from the machine.

• Stop the machine if any one enters the workingarea.

• Clear the area of objects such as stones, toys,wires, etc. that may become caught in theblades and be thrown out.

• Look out for the ejector and do not direct ittowards anyone.

• Stop the engine and prevent the engine frombeing started until you have cleaned the cuttingunit or outlet channel.

• Remember the operator is responsible fordanger or accidents.

• Never carry passengers. The machine is onlyintended to be used by one person.

• Always look downwards and backwards beforeand while reversing. Keep watch for both largeand small obstacles.

• Slow before cornering.

• Switch off the blades when you are not mowing.

SAFETY INSTRUCTIONS

WARNING!This machine can sever hands and feet as well as throw objects.Failure to observe the safety instructions can result in serious injuries.

WARNING!The inserted symbol means that important safety instructions need to be observed. Itapplies to your safety.

Never carry passengers.

Read the operator’s manual before starting the machine.

Clear the area of objects before mowing.

6– English

6003-006

8011-292

• Take care when rounding a fixed object, so thatthe blades do not hit it. Never run the machineover foreign objects.

• Only use the machine in daylight or in otherwell-lit conditions. Keep the machine at a safedistance from holes or other irregularities in theground. Pay attention to other possible risks.

• Never use the machine if you are tired, if youhave consumed alcohol, or if you are takingother drugs or medication that can affect yourvision, judgment or co-ordination.

• Keep an eye on the traffic when working closeto a road or when crossing it.

• Never leave the machine unsupervised with theengine running. Always stop the blades, applythe parking brake, stop the engine and removethe keys before leaving the machine.

• Never allow children or other persons nottrained in the use of the machine to use orservice it. Local laws may regulate the age ofthe user.

SAFETY INSTRUCTIONS

WARNING!Engine exhaust, some of itsconstituents and certain vehiclecomponents contain or emitchemicals considered to causecancer, birth defects or otherreproductive impairment. Theengine emits carbon monoxide,which is a colourless, poisonousgas. Do not use the machine inenclosed spaces.

WARNING!You must use approved personal protective equipment whenever you use the ma-chine. Personal protective equipment cannot eliminate the risk of injury but it willreduce the degree of injury if an accident does happen. Ask your dealer for help inchoosing the right equipment.

• Make sure that you have first aid equipmentclose at hand when using the machine.

• Never use the machine when barefoot. Alwayswear protective shoes or protective boots,preferably with steel toes.

• Wear approved protective glasses or full-facevisor during assembly and when operating.

• Never wear loose fitting clothes that can catch inmoving parts.

• Use ear protectors to eliminate the risk forimpairment of hearing.

Keep children away from the area to be mowed.

Personal protective equipment.

English – 7

8010-054

6003-004

Be especially careful when driving on slopes.

Mow upwards and downwards on slopes, not sideways.

Driving on slopes

Driving on slopes is one of the operations wherethe risk of the driver losing control of the machine orof it overturning is the greatest; this can result inserious injury or death. All slopes demand extracare. If you cannot reverse up a slope or if you feelunsure, do not mow it.

Proceed as follows:

• Remove obstacles such as stones, branches,etc.

• Mow upwards and downwards, not sideways.

• Do not use the machine on ground that slopesmore than 15°.

• Avoid starting or stopping on a slope. If the tyresstart to slip, stop the blades and drive slowlydown the slope.

• Always drive smoothly and slowly on slopes.

• Do not make any sudden changes in speed ordirection.

• Avoid unnecessary turns on slopes, ifnecessary, turn slowly and gradually downwardsif possible.

• Watch out for and avoid driving over furrows,holes and bumps. It is easier for the machine tooverturn on uneven ground. Tall grass can hideobstacles.

• Drive slowly. Use small movements of thesteering wheel. Select a low gear, so you do notneed to stop to change gear. Engine braking onthe machine is also better in a low gear.

• Take extra care if any attachments are fitted thatcan change the stability of the machine.

• Do not mow too close to edges, ditches orbanks. The machine can suddenly overturn ifone wheel comes over the edge of a steep slopeor a ditch, or if an edge gives way.

• Do not mow wet grass. It is slippery, and tyrescan lose their grip so that the machine skids.

• Do not try to stabilize the machine by puttingyour foot on the ground.

• When cleaning the chassis the machine mustnever be driven close to an edge or ditch.

• Follow the manufacturer’s recommendationsregarding wheel weights or counterbalanceweights to increase stability.

SAFETY INSTRUCTIONS

8– English

8010-057

8010-058

Children

• Serious accidents may occur if you fail to be onyour guard for children in the vicinity of themachine. Children are often attracted to themachine and mowing. Never assume thatchildren will remain where you last saw them.

• Keep children away from the area to be mowedand under close supervision by another adult.

• Keep an eye out and shut off the machine ifchildren enter the work area.

• Before and during reversing procedures, lookbehind you and down for small children.

• Never allow children to ride along. They can falloff and seriously injure themselves or be in theway for safe manoeuvring of the machine.

• Never allow children to operate the machine.

• Be particularly careful near corners, bushes,trees or other objects that block your view.

SAFETY INSTRUCTIONS

Never allow children to operate the machine.

Never fill the fuel tank indoors.

Maintenance

• Stop the engine. Prevent starting by removingthe ignition cable from the spark plug or removethe ignition key before making any adjustmentsor carrying out maintenance.

• Never fill the fuel tank indoors.

• Petrol and petrol fumes are poisonous andextremely flammable. Be especially carefulwhen handling petrol, as carelessness canresult in personal injury or fire.

• Only store fuel in containers approved for thepurpose.

• Never remove the fuel cap and fill the petroltank while the engine is running.

• Allow the engine to cool before refuelling. Donot smoke. Do not fill petrol in the vicinity ofsparks or naked flames.

• Observe the risk of environmental damagewhen handling oil, fuel and the battery. Remem-ber to follow local regulations concerning wastehandling.

• Electric shocks can result in injury. Do not touchthe ignition lead when the engine is running. Donot test the ignition system with your fingers.

English – 9

WARNING!The engine, and components ofthe exhaust and hydraulicsystems become extremely hotduring operation. Risk for burnswith contact.

WARNING!The battery contains lead andlead pollutants, chemicals thatare considered to cause cancer,birth defects or other repro-ductive impairment. Wash yourhands after touching thebattery.

8009-242

• If leaks arise in the fuel system, the engine mustnot be started until the problem has beenresolved.

• Store the machine and fuel in such a way thatthere is no risk that leaking fuel or fumes cancause any damage.

• Check the fuel level before each use and leavespace for the fuel to expand, because the heatfrom the engine and the sun may otherwisecause the fuel to expand and overflow.

• Avoid overfilling. If you spill petrol on themachine, wipe up the spill and wait until it hasevaporated before starting the engine. If youspill petrol on your clothing, change yourclothing.

• Allow the machine to cool before performing anyactions in the engine compartment.

• Be especially careful when handling batteryacid. Acid on the skin can cause seriouscorrosive injuries. In the event of spillage on theskin wash immediately with water.

• Acid in the eyes can cause blindness, contact adoctor immediately.

• Take care with battery maintenance. Explosivegases form in the battery. Never performmaintenance on the battery while smoking or inthe vicinity of open flames or sparks. This cancause the battery to explode and cause seriousinjuries.

• Make sure all nuts and bolts are tightenedcorrectly and that the equipment is in goodcondition.

• Do not modify safety equipment. Checkregularly to be sure it works properly. Themachine must not be driven if protective plates,protective covers, safety switches or otherprotective devices are not fitted or are defective.

• Do not change the setting of governors andavoid running the engine at excessively highrevs. If you run too fast, you risk damaging themachine components.

• Observe the risk of injury caused by moving orhot parts if the engine is started with the enginecover opened or the protective covers removed.

SAFETY INSTRUCTIONS

Do not smoke when carrying out maintenance.

10– English

8009-467

8010-061

SAFETY INSTRUCTIONS

• Never use the machine indoors or in spaceslacking proper ventilation. Exhaust fumescontain carbon monoxide, an odourless,poisonous and highly dangerous gas.

• Stop and inspect the equipment if you run overor into anything. If necessary, make repairsbefore starting.

• Never make adjustments with the enginerunning.

• The machine is tested and approved only withthe equipment originally provided orrecommended by the manufacturer.

• The blades are sharp and can cause cuts. Wrapthe blades or wear protective gloves whenhandling them.

• Check regularly that the parking brake works.Adjust and maintain as required.

• The mulching unit should only be used wherebetter quality mowing is required and in knownareas.

• Reduce the risk of fire by removing grass,leaves and other debris that may have fastenedon the machine. Allow the machine to coolbefore putting it in storage.

Transport

• The machine is heavy and can cause seriouscrush injuries. Be especially careful when it isloaded in or out of a car or on and off of a trailer.

• Use an approved trailer to transport the ma-chine. Activate the parking brake and secure themachine using approved fasteners, such astension belts, chains or ropes when transporting.

• Check and observe local road traffic regulationsbefore transporting or driving the machine onroads.

IMPORTANT INFORMATION

The parking brake is not sufficient to lock themachine during transport. Ensure you securethe machine firmly to the transporting vehicle.Reverse the machine on to the transportingvehicle to prevent it from overturning.

Regularly clean grass, leaves and other debris from themachine.

Never run the machine in an enclosed area.

English – 11

8009-244

8009-245

8009-243

7 8 9 10 11 12

6 5 4 3 2113

PRESENTATION

Presentation

Congratulations on your choice of an exceptionallyhigh quality product.

Four models equipped with engines from Briggs &Stratton are described in this operator’s manual.

FR 2111 has an inline type gearbox with 5 forwardgears and reverse.

On FR 2113 and FR 2116 transmission is by meansof a variable speed hydrostatic gearbox.

FR 2113 is available in two versions. FR 2113 A hasa mowing deck with rear ejection and FR 2113 MAhas a mowing deck with mulching.

Placement of controls

1. Ignition key

2. Throttle/Choke control

3. Adjustment of the cutting height

4. Lifting lever, mowing deck

5. Accelerator for reversing, FR 2113,FR 2116

6. Accelerator for driving forwards, FR 2113,FR 2116Parking brake, FR 2111

7. Parking brake, FR 2113, FR 2116Clutch pedal, FR 2111

8. Lock button for the parking brakeleft-hand side for FR 2113, FR 2116right-hand side for FR 2111

9. Seat adjustment

10. Fuel cap

11. Main lock (under seat)

12. Lever for disengaging the drive, FR 2113,FR 2116.

13. Gear shift lever, FR 2111

12– English

8009-246

6004-005

6004-006

PRESENTATION FR 2111

Throttle and Choke controls

The throttle is used to control the speed of theengine and thereby also the rotation speed of theblades.

The control is also used to activate the choke.When the choke is engaged a richer fuel/air mixtureis fed to the engine, which facilitates starting in thecold.

Clutch pedal

The clutch pedal disengages the engine and stopspropulsion.The blade drive is not affected by the clutch pedal.

Brake pedal / Parking brake

The brake pedal activates a disc brake that islocated on the gearbox and stops the drive gear.The clutch pedal should also be pressed downwhen braking to achieve the best braking effect.

The brake pedal also acts as a parking brake if thelock button is pressed in when the pedal is presseddown.

English – 13

8009-247

8009-248

6004-006H

PRESENTATION FR 2113, FR 2116

Parking brake

The parking brake is activated as follows:

1. Press down the brake pedal.

2. Press in the lock button on the steering column.

3. Release the brake pedal while holding inthe button.

The parking brake lock is automatically disengagedwhen the brake pedal is pressed down.

Throttle and Choke controls

The throttle is used to control the speed of theengine and thereby also the rotation speed of theblades.

The control is also used to activate the choke.When the choke is engaged a richer fuel/air mixtureis fed to the engine, which facilitates starting in thecold.

Accelerator

The speed of the machine is variably controlledusing two pedals. Pedal (1) is used to travel for-wards and pedal (2) to reverse.

WARNING!Make sure that no branches caninterfere with the pedals whenmowing under bushes.Risk for unintentionalmanoeuvring.

14– English

8009-249

8009-250

8009-261

8009-260

PRESENTATION

Lifting lever for the mowing deck

The lifting lever is used to put the mowing deck ineither the transport or mowing positions.

If the lever is pulled backwards the deck is raisedand the blades automatically stop rotating (trans-port position).

If the lock button is pressed in and the lever ismoved forwards the deck will be lowered and theblades will automatically start to rotate (mowingposition).

The lever can also be used to temporarily adjust thecutting height, for example, with a small mound inthe lawn.

Mowing deck

FR 2111 and FR 2113 A have a triple blade mowingdeck with rear ejection, i.e. the clippings are thrownout behind the mowing deck.

FR 2113 MA has a double blade mulching unit andFR 2116 MA has a triple blade Combi unit, whichcan be set to either a mulching function or rearejection by removing a mulching plug.

Lifting the mowing deck (transport position)

Lowering the mowing deck (mowing position)

English – 15

8009-251

6004-014

8009-252

PRESENTATION

Lever to adjust the cutting height

Using the lever the cutting height can be adjusted in9 different positions.

Deck with rear ejection, 40-90 mm(1 9/16" - 3 9/16")

Mulching and combi unit, 45-95 mm(1 3/4" - 3 3/4")

Seat

The seat has a hinged mounting on the front edgeand can be folded forwards.

The seat can also be adjusted lengthways.

Loosen the handles under the seat and adjust itforwards or backwards to the desired position.Secure the adjustment using the handles.

WARNING!Petrol is highly flammable.Observe caution and fill the tankoutdoors(see the safety instructions).

Refuelling

The engine should be run on a minimum of85-octane grade unleaded petrol (not mixed withoil). It can be beneficial to use environmentallyadapted alkylate petrol.

Do not use petrol that contains methanol.Do not fill the tank completely, leave an expansionarea of at least 2.5 cm (1").

16– English

DRIVING

3. On FR 2111Put the gear shift lever in the N position(neutral).

Starting the engine

1. Lift up the mowing deck by pulling the leverbackwards to the locked position (transportposition).

2. Activate the parking brake. This is done asfollows:

• Press down the brake pedal (1).

• Press in the lock button on the steeringcolumn (2).

• Release the brake pedal while keeping thebutton pressed in.

The parking brake’s lock is automaticallydisengaged when the brake pedal is presseddown.

The FR 2111 has the brake pedal and lockbutton on the right-hand side.

Before starting

• Read the safety instructions and informationconcerning the placement of controls andfunctions before starting.

• Carry out daily maintenance before starting(see the maintenance schedule).Adjust the seat to the desired position.

IMPORTANT INFORMATION

Do not press down the reversing lock buttonon the lever when engaging the neutralposition. Otherwise this will activate the startlock function.

1

2

N

8009-249

6007-002H

8009-253

8009-430

IMPORTANT INFORMATION

The air intake grille in the engine coverbehind the driver’s seat must not beblocked by, for example, clothing, leaves,grass or dirt.

Impaired cooling of the engine. Risk ofmajor engine damage.

English – 17

STOP START

1 2

3

1 2

3

8009-254

8009-255

8009-256

IMPORTANT INFORMATION

Do not run the starter motor for more than15 seconds at a time. If the engine doesnot start wait about 1 minute before tryingagain.

DRIVING

With a cold engine:4. Move the throttle to position 3 (choke position).

In this position the engine is fed with a richermixture, which means the engine is easier tostart.

The throttle must be moved to the side (towardsthe ignition key) to reach the choke position.

6. Turn the ignition key to the start position.

With a warm engine:5. Move the throttle in between positions 1 and 2.

18– English

N

STOP START

8009-257

6007-010H

8009-248

8009-253

DRIVING

WARNING!Never run the engine indoors, inenclosed or badly ventilatedareas. Engine exhaust fumescontain poisonouscarbon monoxide.

7. Once the engine has started release the ignitionkey back to the neutral position.

Move the throttle to the required engine speed.When mowing 3/4 to full throttle.

IMPORTANT INFORMATION

Gear changes between forward gears mustnot be made while the machine is moving.

The engine must be disengaged during eachgear change.

Stop the machine before changing betweenforward and reverse gears, otherwise thismay result in damage to the gearbox.

Never use force to engage a gear. If a geardoes not engage immediately, release theclutch pedal and press it down again. Now tryto engage the gear again.

Driving the Rider

1. Release the parking brake by pressing down thebrake pedal.

2. On FR 2113, FR 2116

Carefully press down one of the pedals until therequired speed is obtained.

Pedal (1) is pressed down to travel forwards andpedal (2) to reverse.

On FR 2111

Disengage the engine and select the requiredgear.

The lock button must be held in to engagereverse gear.

• Gears 1-4 are used for mowing

• Gears 4-5 are used for transporting

Starting can take place independent of whichgear is selected.

English – 19

8009-251

8009-250

Mowing pattern

WARNING!Clean all stones and other objectsthat can be thrownby the blades from the lawn.

DRIVING

3. Select the required cutting height (1-9) using thecutting height lever.

In order to obtain an equal cutting height, it isimportant that the air pressure is the same inboth front wheels (60 kPa/8.5 PSI).

Mowing tips

• Find and mark out any stones and other fixedobjects to avoid colliding with them.

• Start with a high cutting height and reduce ituntil the desired mowing result is obtained.

• The best mowing result is achieved with highengine revs (the blades rotate quickly) and lowspeed (the Rider moves slowly). If the grass isnot too long and thick the driving speed can beincreased without significantly impairing themowing result.

4. Press in the lock button on the lifting lever andlower the mowing deck.

IMPORTANT INFORMATION

The life span of the drive belts is in-creased significantly if the engine runs ata low speed when the blades are engaged.Therefore only accelerate once the mow-ing deck has been lowered into the mow-ing position.

• The finest lawns are obtained if they are mownfrequently. Mowing will be more even and theclippings will be more evenly distributed acrossthe area. The overall mowing time will not belonger as higher driving speeds can be selectedwithout impairing the mowing result.

• Avoid mowing wet lawns. The mowing result willbe poorer as the wheels will sink into the softlawn.

• Rinse off the underside of the mowing deck afteruse with water, do not use a high pressurewasher. Now put the mowing deck in the serviceposition.

• It is extremely important when the Mulching unitis used that the intervals between mowing arenot too long.

20– English

STOP START

MAX 15°

6007-013

8009-249

8009-258

8009-259

DRIVING

WARNING!Do not use the Rider on groundthat slopes more than 15°. Mowupwards and downwards onslopes, never sideways. Avoidsudden changes in direction.

Clutch control FR 2113, FR2116

The clutch control must be pulled out in order forthe Rider to be moved when the engine is shutoff.

Starting on slopes, manual gearbox

1. Press down the parking brake

2. Move the throttle to full throttle.

3. Disengage the engine and select 1st gear.

4. Gradually release the clutch pedal.

5. When the engine starts to pull, release theparking brake.

Stopping the engine

Preferably let the engine idle for a minute so it runsat its normal working temperature before it isstopped if it has worked hard.

1. Lift up the mowing deck by pulling the leverbackwards to its end position.

2. FR 2111: Pull back the throttle and move thegear shift lever to the neutral position N, withoutpressing in the reversing lock button.Turn the ignition key to the STOP position.

FR 2113, FR 2116: Pull back the throttle andturn the ignition key to the STOP position.

3. When the Rider is at a standstill, hold down theparking brake and press in the reversing lockbutton.

English – 21

Maintenance schedule

The following is a list of maintenance procedures that must be performed on the Rider. For those points notdescribed in this manual, visit an authorised service workshop.

● = Described in this operator’s manual.❍ = Not described in this operator’s manual.

WARNING!No service operations may be performed on the engine or mowing deck unless:

• The engine has been stopped. • The parking brake is actuated.• The ignition key has been removed. • The mowing deck is disengaged.• The ignition cable has been removed from the spark plug.

MAINTENANCE

1) First change after 5 hours. Replace after every 25 hours with heavy loads or high temperatures. 2) Under dusty conditions cleaning and replacement should take place more frequently.3) With daily use, the Rider should be lubricated twice weekly.4) Performed by an authorised service workshop.

Check the engine oil level 39 ●

Check the engine’s cooling air intake 31 ●

Check the fuel pump’s air filter 28 ●

Check the steering wires 24 ●

Check the brakes 25 ●

Check the battery 28 ●

Check the safety system 29 ●

Check nuts and bolts – ❍

Check for any fuel or oil leakage – ❍

Clean around the silencer – ❍

Change the engine oil 1) 39 ● 1) ● 1)

Replace the air filter’s prefilter on FR 21162) 27 ●

Check the mowing deck 32 ●

Check the air pressure in the tyres (60 kPa/8.5 PSI) 31 ●

Lubricate the belt adjuster3) 40 ●

Lubricate joints and shafts 3) 40 ●

Adjust the brakes FR 2111 25 ●

Check the V-belts – ❍

Check the transmission’s cooling fins on FR 2113, 2116 – ❍

Check the transmission’s oil level on FR 2113, 2116 40 ●

Adjust the brakes on FR 2113, 2116 25 ●

Inspecting and adjusting the throttle cable 26 ●

Clean the engine’s and transmission’s cooling fins 2,4) – ❍

Replace the air filter’s prefilter and paper filter 2) 27 ●

Replace the fuel filter 26 ●

Replace the spark plug 28 ●

50 100Page

Maintenanceinterval hours

25Maintenance

Dailymaintenance

beforestarting

22– English

8009-262

8009-263

8009-264

MAINTENANCE

Front cover FR 2113 MA, FR 2116 MALoosen the snap-in lock and lift off the cover.

Dismantling the Rider covers

Engine coverThe engine becomes accessible for service whenthe engine cover is folded up.Fold the seat forward, loosen the rubber strapunder seat and fold the cover backwards.

Front cover FR 2111, FR 2113 ARemove the bolts holding the front cover (3) and liftoff the cover.

English – 23

8009-265

8009-266

MAINTENANCE

Left-hand wing cover

Remove the bolts holding the wing cover and lift offthe cover.

Right-hand wing cover

Remove the bolts holding the wing cover (2 and 3).On FR 2113 and FR 2116 the knob (1) should alsobe removed.

24– English

8009-267

6008-009

6008-010

MAINTENANCE

3. If necessary, the wires can be adjusted bytightening the adjuster nuts on each side of thesteering collar. Do not tension the wires toomuch, they should only be tightened against thesteering collar.

Support the wire so it does not twist.

If you only tension one side the steering wheel’scentre position may change.

Check the wire tension as set out in point 2after you have made the adjustment.

Checking and adjusting the steeringwires

The steering is governed by means of wires.

After a period of use these can become stretched,which means the steering setting may havechanged.

The steering is checked and adjusted as follows:

1. Dismantle the frame plate by removing the bolts(two on each side).

2. Check the tension of the steering wires bysqueezing them together by the arrows asillustrated.It should be possible to squeeze the wires sothat the distance between them is half the size,without using too much force.

English – 25

21 1

6008-239H

6008-012

6008-011

WARNING!A badly adjusted brake can resultin impaired braking capacity.

Checking and adjusting the brake onFR 2113 and FR 2116

Check that the brake is correctly adjusted byplacing the Rider on a slight downhill and activatethe brake.

If the Rider does not standstill the brake needsadjusting.

The brake is adjusted as follows:

1. Loosen the locking nuts (1).

2. Tension the wire using the adjuster screw (2)until the play on the wire disappears.

3. Tighten the locking nuts (1).

4. The brake should be checked again after theadjustment has been made.

Checking the brake FR 2111

The brake is a disc brake and is located on thegearbox.Check that the brake is adjusted correctly bymeasuring the distance between the brake leverand front edge of the cut-out on the chassis.The distance should be 0-1 mm (0-0.040") whenthe brake is not actuated.

Adjusting the brakeFR 2111

1. Loosen the locking nuts (1).

2. Tension the wire using the adjuster screw (2) sothat the distance between the brake lever andcut-out’s front edge on the chassis is 1 mm(0.040").

3. Tighten the locking nuts (1) after adjustment.

MAINTENANCE

26– English

MAINTENANCE

Replacing the fuel filter

Replace the new fuel filter mounted on the supplyline after every 100 hours (once per season) ormore frequently if it is clogged.

Replace the filter as follows:

1. Fold up the engine cover.

2. Move the hose clips away from the filter.Use a pair of flat pliers.

3. Pull the filter away from the ends of the hose.

4. Press the filter into the ends of the hose. Ifnecessary, a soap solution can be applied tothe ends of the filter to simplify assembly.

5. Move the hose clips back towards the filter.

2. Pull the throttle cable’s casing as far as possibleto the right and check that the choke is fullyactuated.

3. Tighten the clamping screw.

Adjusting the throttle cable

The throttle cable may need to be adjusted, if theengine does not respond as it should whenaccelerating, if it produces black smoke ormaximum revs are not reached.

1. Loosen the clamping screw (by the arrow), andslide the throttle to the choke position.

4. Pull back the throttle to the full throttle positionand check that the choke is no longer actuated.

8009-402

8009-403

8009-404

8009-405

English – 27

Replacing the air filter

If the engine seems to lack power or goes irregu-larly the reason may be that the air filter is clogged.

It is therefore important to replace the air filter atregular intervals (see ”Maintenance schedule” forcorrect service interval).

1. Fold open the engine cover.

2. Pull up the handle on the air filter cover, unhookand turn towards the engine.

3. Remove the air filter cover.

4. Lift out the air filter cartridge from the fanhousing.

Replace the paper filter if it is clogged with dirt.

MAINTENANCE

IMPORTANT INFORMATION

Do not use compressed air to clean thepaper filter.

Filters should not be oiled. They should beassembled dry.

5. Carefully lift the precleaner out of the fanhousing. Carefully clean the fan housing so thatdirt does not fall down into the carburetor.

6. Insert a new precleaner and air filter cartridgein the fan housing.

7. Align the tabs on the cover with the slits in thehousing and replace the air filter cover.

8. Pull the handle outwards. Secure the handle inthe air filter cover and close the cover bypressing it inwards.

8009-406

8009-409

8009-408

8009-407

8009-410

28– English

6008-013

MAINTENANCE

Checking the fuel pump’s air filter

Check regularly that the fuel pump’s air filter is notclogged by dirt.

The filter can be cleaned using a brush, if neces-sary.

WARNING!Actions with acid contact

External: Rinse thoroughly with water.

Internal: Drink large quantities of water ormilk. Contact a doctor as soon aspossible.

Eyes: Rinse thoroughly with water.Contact a doctor as soon aspossible.

The battery emits explosive gases. Sparks,flames and cigarettes must not be present inthe vicinity of the battery.

Checking the acid level in the battery

Check that the acid level in the battery lies betweenthe markings. When refilling only distilled water maybe used to fill the cells.

Ignition systemThe engine is equipped with an electronic ignitionsystem. Only the spark plug requires maintenance.

For the recommended spark plug, see Technicaldata.

IMPORTANT INFORMATION

Fitting the wrong spark plug type can damagethe engine.

1. Remove the ignition cable shoe and cleanaround the spark plug.

2. Remove the spark plug with a 5/8" (16 mm)or13/16" (21 mm) spark plug socket wrench.

3. Check the spark plug. Replace the spark plug ifthe electrodes are burned or if the insulation iscracked or damaged. Clean the spark plug witha wire brush if it is to be reused.

4. Measure the electrode gap with a gapping tool.The gap should be 0.75 mm (0.030"). Adjust asnecessary by bending the side electrode.

IMPORTANT INFORMATION

Inadequately tightened spark plugs cancause overheating and damage the engine.Tightening the spark plug too much candamage the threads in the cylinder head.

5. Reinsert the spark plug, turning by hand toavoid damaging the threads.

6. After the spark plug is seated, tighten it using aspark plug wrench so that the washer iscompressed. A used spark plug should beturned 1/8 of a turn from the seated position. Anew spark plug should be turned 1/4 a turnfrom the seated position.

7. Replace the ignition cable shoe.

8009-411

IMPORTANT INFORMATION

Do not turn over the engine if the sparkplug or ignition cable has been removed.

English – 29

Checking the safety system

The Rider is equipped with a safety system thatprevents starting or driving under the followingconditions.

The engine should only be possible to start whenthe mowing deck is in its raised position and thegear shift lever or hydrostat pedals are in theneutral position.

The driver does not need to be seated in thedriver’s seat.

Make daily inspections to ensure that the safetysystem works by attempting to start the enginewhen one of the conditions is not met. Change theconditions and try again.

Check that the engine stops if you temporarilymove out of the driver’s seat while the mowing deckis lowered or the gear shift lever/hydrostat pedalsare not in the neutral position.

Starter

Ignition system

Works

Does not work

MAINTENANCE FR 2111

N

FR 2111

30– English

FR 2113, FR 2116

Checking the safety system

The Rider is equipped with a safety system thatprevents starting or driving under the followingconditions.

The engine should only be possible to start whenthe mowing deck is in its raised position and thegear shift lever or hydrostat pedals are in theneutral position.

The driver does not need to be seated in thedriver’s seat.

Make daily inspections to ensure that the safetysystem works by attempting to start the enginewhen one of the conditions is not met. Change theconditions and try again.

Check that the engine stops if you temporarilymove out of the driver’s seat while the mowing deckis lowered or the gear shift lever/hydrostat pedalsare not in the neutral position.

Starter

Ignition system

Works

Does not work

MAINTENANCE FR 2113, FR 2116

English – 31

Checking the tyres’ air pressure

The tyres’ air pressure should be 60 kPa(0.6 kp/cm2/8.5 PSI) on all wheels.In order to improve the drive power the pressure inthe rear tyres can be reduced to 40 kPa(0.4 kp/cm25.6 PSI).The highest permitted pressure is 100 kPa(1.0 kp/cm2/14 PSI).

IMPORTANT INFORMATION

Different air pressure in the front tyres willresult in the blades mowing the grass atdifferent heights.

MAINTENANCE

Checking the engine’s cooling air intake

FR 2111, FR 2113, FR 2116Clean the air intake grille in the engine coverbehind the driver’s seat.

Fold up the engine cover.

Check that the engine cooling air intake is free ofleaves, grass and dirt.

Check the air duct, located on the inside of theengine cover, ensure it is clean and does not rubagainst the cooling air intake.

A clogged air duct or cooling air intake impairs thecooling of the engine, which may result in enginedamage.

8009-262

8009-268

8009-412

8009-370

R I D E R 8 5 0

R I D E R 8 5 0

Main fuse

The fuse is located in a loose holder under thebattery case cover, in front of the battery.Type: Flat-blade mounting, 15 A.Do not use any other type of fuse when replacing.A blown fuse indicates that the mounting has burntoff.Pull the fuse out of the holder when replacing. Thefuse is used to pro ect the electrical system. If itblows again shortly after replacing this is due to ashort circuit, which must be rectified before themachine is used again.

WARNING!The cooling air intake rotateswhen the engine is running. Mindyour fingers.

Air intake grille

Cooling air intake

32– English

8009-269

8009-270

8009-271

Checking and adjusting the mowingdeck’s ground pressure onFR 2113 MA and FR 2116 MA

In order to achieve the best mowing result themowing deck should follow the ground withouttouching it too heavily.The pressure is adjusted using a screw on eachside of the Rider.

1. Check that the tyres’ air pressure is 60 kPa(0.6 kp/cm2/8.5 PSI).

2. Place a pair of bathroom scales under themowing deck’s frame (on the front edge) so thatthe mowing deck rests on the scales. Ifnecessary a block can be placed between theframe and the scales so that the support wheelsdo not support any weight.

Checking the parallelism of the mowingdeck

Check the mowing deck’s parallelism as follows:

1. Check that the tyres’ air pressure is 60 kPa (0.6 kp/cm2/8.5 PSI).

2. Place the Rider on a flat surface.

3. Measure the distance between the ground andthe front and back edges of the deck cover.

The mowing deck should have a slight slant,with the rear edge 2-4 mm (1/8") higher than thefront edge.

MAINTENANCE

3. Adjust the mowing deck’s ground pressure byscrewing the adjuster screws, which are locatedbehind the front wheels on both sides, in or out.

The ground pressure should be between 12 and15 kg (26.5 - 33 lbs).

English – 33

2

6008-026H

8009-138

MAINTENANCE FR 2111, FR 2113 MA

Adjusting the parallelism of the mowingdeck on FR 2111

1. Check that the tyres’ air pressure is 60 kPa(0.6 kp/cm2/8.5 PSI).

2. Dismantle the front cover and the right-handwing cover as described on pages 22-23.

3. Vertical adjustment of the mowing deck iscarried out using the adjuster nuts at the rear ofthe lifting stay.

4. Raise the mowing deck at the front edge byshortening the lifting stay.Lower the mowing deck at the front edge bylengthening the lifting stay.

5. Tighten the nuts against each other afteradjustment.

6. The parallelism should be checked again afterthe adjustment has been made.

7. Fit the right-hand wing cover and the front cover.

Adjusting the parallelism of the mowingdeck on FR 2113 MA

1. Check that the tyres’ air pressure is 60 kPa(0.6 kp/cm2/8.5 PSI).

2. Remove the front cover and the right-hand wingcover.

3. Loosen the nut (1) on the parallelism stay.Remove the locking clip (2) and the parallelismstay.

4. Turn the fork anticlockwise to raise the cover’srear edge, clockwise to lower the cover’s rearedge.

5. Secure the parallelism stay using the locking clipand tighten the nut after adjustment.

6. The parallelism should be checked again afterthe adjustment has been made.

7. Fit the right-hand wing cover and the front cover.

34– English

6017-155

Adjusting the parallelism of the mowingdeck on FR 2116 MA

1. Check that the tyres’ air pressure is 60 kPa(0.6 kp/cm2/8.5 PSI).

2. Remove the front cover and the right-hand wingcover.

3. Loosen the parallelism stay’s nuts.

4. Screw out (extend) the stay to raise the rearedge of the cover. Screw in (shorten) the stay tolower the rear edge of the cover.

5. Tighten the nuts after adjustment.

6. The parallelism should be checked again afterthe adjustment has been made.

7. Fit the right-hand wing cover and the front cover.

MAINTENANCE FR 2116 MA

8009-289

Removing the mulching plug

You need to remove the mulching plug, which isfitted under the cutting unit with three screws, tochange a combi unit from a mulching function to acutting unit with rear ejection.

1. Put the cutting unit in the service position, see”Placing in the service position”.

2. Remove the three screws holding the mulchingplug, and remove the plug.

3. Tip: Fit three, full-threaded screws M8x15 mmin the screw holes to protect the threads.

4. Return the unit to the normal position.

To fit the mulching plug, follow the instructions inthe reverse order.

English – 35

P1

6017-218

6017-219

6017-220

MAINTENANCE FR 2113 MA, FR 2116 MA

The mowing deck’s service position

In order to provide good accessibility for cleaning,repair and servicing, the mowing deck can be set inthe service position. The service position meansthat the mowing deck is raised and locked in thevertical position.

Placing in the service position

1. Position the machine so it stands flat. Activatethe parking brake (1). Set the mowing deck tothe lowest cutting height and lower the mowingdeck.

3. Loosen the two support wheels, located underthe front cover.

2. Remove the front cover by loosening the splitpin. (Complete instructions for the serviceposition can be found on the inside of the frontcover).

36– English

6017-221

8009-272

8009-122

6017-223

MAINTENANCE FR 2113 MA, FR 2116 MA

4. Fit the two support wheels on each side of themowing deck’s rear section.

5. Loosen the spring on the drive belt’s belt idler.

6. Put your foot on the front edge of the mowingdeck next to the wheel and lift the mowingdeck’s front edge to make it easier to loosen theheight adjustment stay.

WARNING!Wear protective glasses whendismantling the mowing deck.The spring that tension the beltcan fly off and cause personalinjury.

7. Secure the stay in the holder.

English – 37

2

1

6017-225

6017-226

6017-227

8009-438

MAINTENANCE FR 2113 MA, FR 2116 MA

8. Lift off the drive belt (1).Now pull out the split pin (2).

9. Pull the frame forwards and refit the pin.

10. Grasp the mowing deck’s front edge, pull outand lift up into the service position.

If the cylindrical bolt, which is now holding themowing deck is removed, the mowing deck canbe lifted off.

Releasing the service position

To release the service position, reverse the proce-dures set out in Placing in the service position.Make sure that the mowing deck’s lug (3) enters theloop correctly on the underside of the machine, seediagram.

WARNING!Exercise care so that your handsare not crushed.

38– English

6008-024

6017-023

8009-137a

Mowing deck (rear ejection)

Mulching 90 cm FR 2113 MA

8009-288Combi 103 cm FR 2116 MA

MAINTENANCE

Inspecting the blades

It is important that the blades are undamaged andwell-ground to give the best mowing result.

Check that the blades’ mounting bolts aretightened.

IMPORTANT INFORMATION

Replacement or sharpening of the bladesshould be carried out by an authorisedservice workshop.

IMPORTANT INFORMATION

The blades on the double blade Mulching unitshould always be set relative to each other asillustrated, with a 90° angle between theblades. Otherwise the blades can collide andcause damage to the mowing deck.

The blades should be balanced after sharpening.

Damaged blades should be replaced when hittingobstacles that result in a breakdown. Let theservicing dealer judge whether the blade can berepaired/ground or must be discarded.

Replacing the shear pin FR 2113 MAThe blades are fitted with a shear pin to protect theMulching unit and its drive when colliding withobstacles. A domed, spring friction washer is fittedto each blade bolt. The washer must always bereplaced with a new washer when replacing theshear pin. Otherwise the shear pin can breakcausing the blades to collide.

Only use original spare parts. A set containing ablade, shear pin and friction washer can bepurchased from your dealer.

1. Put the cutting unit in the service position, see”Service position for the cutting unit\Placing inthe service position”.

2. Remove the blade (2A) by removing the bladebolt with washer and friction washer (2B).

3. Remove the remains of the broken shear pin (3).

4. Make sure the contact surfaces (4) on the bladeand the blade mounting are free from metal.Clean if necessary.

5. Fit a new shear pin (5) in the blade mounting.

6. Fit the blade (6), make sure it is fitted as illus-trated.

7. Fit a new friction washer (7) with the concaveface turned towards the blade.

8. Fit the blade bolt with washer (8). Tighteningtorque 45-50 Nm (4.5-5 kpm/32-36 lbft)

English – 39

LUBRICATION

Changing the oil

The oil should be changed for the first time after 5hours of running time. Thereafter it should bechanged every 50 hours of running time.

With heavy loads or high temperatures replace theoil after every 25 hours.

WARNING!Engine oil can be very hot if it isdrained off directly after the engineis stopped. Therefore allow theengine to cool down first.

IMPORTANT INFORMATION

Used engine oil is hazardous to health andenvironment and must in accordance withthe law not be poured out on the groundor in the nature, and must be handed in toa workshop or other designated station fortreatment. Avoid skin contact, wash withsoap and water in the event of spillage.

Check the engine’s oil level

Check the oil level in the engine when the Riderstands horizontal with the engine switched off.

Fold open the engine cover.

Release the dip stick and pull out. Wipe off the oiland insert again.

The dip stick must be fully screwed down.

Now release the dip stick again and pull out. Checkthe oil level.

The oil level should lie between the markings on dipstick. If the level approaches the ADD mark, top upwith oil to the FULL mark.

The oil is filled in the same hole for the dip stick.

Fill the oil slowly. Tighten the dipstick correctlybefore starting the engine. Start and run the engineat idling speed for approx. 30 seconds. Turn off theengine. Wait 30 seconds and check oil level. Ifnecessary fill so that the oil comes up to the ”FULL”mark on the dipstick.

First and foremost use synthetic engine oil classSJ-CF 5W/30 or 10W/30 for all temperature ranges.Mineral oil SAE30, class SF–CC can be used attemperatures > +5°C (40°F).

Do not mix different types of oil.

1. Place a receptacle under the engine’s drainplug, located on the left-hand side of the engine.

2. Remove the dip stick and drain plug.

3. Let the oil run out into the receptacle.

4. Fit the drain plug and tighten.

5. Fill up with oil to the FULL mark on the dip stick.The oil is filled in the same hole for the dip stick.See ”Checking the engine’s oil level” above forfilling instructions. The engine holds 1.4 litres(1.5 USqt) of oil.

6. Run the engine warm and then check that thereis no leakage from the drain plug.

ADD FULL

ADD FULL

8009-413

6008-035

8009-414

40– English

8009-273

6008-240H

6008-232

LUBRICATION

Checking the oil level in the transmissionon FR 2113, FR 2116

1. Remove the transmission cover. Loosen bothscrews (one on each side) and lift off thetransmission cover.

2. Check that there is oil in the transmission’s oiltank. Fill if necessary with engine oilSAE 10W/30 (class SF-CC).

Lubricating the belt adjuster

The belt adjuster should be lubricated regularlyusing good quality molybdenum disulphide grease*.1 nipple from the right-hand side under the engine’slower belt pulley, until grease is forced out.

With daily use, lubrication should be carried outtwice weekly.

General lubrication

All joints and bearings are lubricated usingmolybdenum disulphide grease during manu-facture. Continue to lubricate using the same typeof grease *. Lubricate the steering and control wiresusing engine oil.

Carry out this lubrication regularly; with daily use,the machine should be lubricated twice weekly.

* Grease from well-known brand names (petrolcompanies, etc.) usually maintains a good quality.The most important property is that the greaseprovides good protection against corrosion.

English – 41

8009-274

Lubricating the front wheel bearings

The front cover and wing covers must be removedon machines with rear ejection, so that the tubularloop can be lifted to remove the wheel.

1. Remove the plastic cover that covers the centreof the wheel.

2. Remove the circlip and washer on the frontwheel axle.

3. Lift off the wheel.

4. Lubricate the stub axle with molybdenumdisulphide grease*.

5. Fit the parts in the reverse order.

IMPORTANT INFORMATION

Check that the circlip enters the groovecorrectly.

LUBRICATION

* Grease from well-known brand names (petrolcompanies, etc.) usually maintains a good quality.The most important property is that the greaseprovides good protection against corrosion.

42– English

Problem Cause

The engine will not start • No fuel in the fuel tank• Faulty spark plug• Fault spark plug connection• Dirt in the carburettor or fuel line

Starter does not turn the engine • Discharged battery• Bad contact between the cable and battery pole• Lifting lever for the mowing deck in the wrong position• Main fuse blown. The fuse is placed in front of

the battery, under the battery cover.• Faulty ignition switch• Gear shift/hydrostat pedals not in the neutral position

The engine runs erratically • Faulty spark plug• Incorrect carburettor setting• Clogged air filter• Blocked fuel tank ventilation• Incorrect ignition setting• Dirt in carburettor or fuel pipe• Choking or incorrectly adjusted throttle cable

The engine lacks power • Clogged air filter• Faulty spark plug• Dirt in the carburettor or fuel line• Incorrect carburettor setting• Choking or incorrectly adjusted throttle cable

Engine overheating • Engine overloaded• Air intake or cooling fins clogged• Damaged fan• Too low or no oil in the engine• Faulty pre-ignition• Faulty spark plug

Battery does not charge • One or more cells are defective• Bad contact between the battery poles and cables

The Rider vibrates • The blades are loose• The engine is loose• Imbalance on one or more blades, due to damage

or inferior balancing after grinding

Uneven mowing result • Blades dull• Mowing deck set incorrectly• Tall or wet grass• Grass build up under the cover• Different air pressure in the right and left-hand tyres• Too high driving speed• Drive belt slips• The blade has a broken shear pin (Mulching)

TROUBLE SHOOTING CHART

English – 43

8009-243

8009-244

To ready the Rider for storage, follow these steps:

1. Clean the Rider carefully, especially under themowing deck. Touch up damage to the paint toprevent rust.

2. Inspect the Rider for worn or damaged parts andtighten any nuts or bolts that may have becomeloose.

3. Change the engine oil; dispose of properly.

4. Empty the fuel tank. Start the engine and let itrun so that even the petrol in the carburettor isemptied.

5. Remove the spark plug and pour about atablespoon of engine oil in the cylinder. Turnover the engine so that the oil is evenlydistributed and then refit the spark plug.

6. Lubricate all grease nipples, joints and shafts.

7. Remove the battery. Clean, charge and store ina cool place.

8. Store the Rider in a clean, dry place and cover itfor extra protection.

Cover

There is a cover to protect your machine duringstorage or transport. Contact your dealer for ademonstration.

Service

When ordering spare parts, please specify thepurchase year, model, type, and serial number ofthe Rider.

Always use genuine spare parts.

An annual check-up or trimming at an authorisedservice workshop is a good way to ensure that yourRider performs at its best the following season.

Winter storage

At the end of the mowing season the Rider shouldbe readied for storage, likewise if it will not be inuse for longer than 30 days. Fuel allowed to standfor long periods of time (30 days or more) can leavesticky residues that can clog the carburettor anddisrupt engine function.

Fuel stabilisers are an acceptable option as regardsavoiding sticky residues during storage. If alkylatepetrol is used, stabilisers are unnecessary becausethis fuel is stable. However, you should avoidswitching between regular and alkylate petrol assensitive rubber components can harden. Addstabiliser to the fuel in the tank or in the storagecontainer. Always use the mixing ratios specified bythe manufacturer of the stabiliser. Run the enginefor at least 10 minutes after adding the stabiliser sothat it reaches the carburettor. Do not empty thefuel tank and the carburettor if you have addedstabiliser.

STORAGE

WARNING!Never store an engine with fuel inthe tank indoors or in poorlyventilated spaces where fuelvapour can come in contact withopen flames, sparks or a pilotlight such as in a boiler, hotwater tank, clothing drier, etc.Handle the fuel with caution. It isvery flammable and careless usecan cause serious damage toperson and property. Drain thefuel into an approved containeroutdoors and far away from openflames. Never use petrol forcleaning. Use a degreasing agentand warm water instead.

44– English

Dimensions FR 2111 FR 2113 A

Length with mowing deck 2040 mm/6.6 ft 2040 mm/6.6 ftWidth 880 mm/2.89 ft 880 mm/2.89 ftHeight 1070 mm/3.52 ft 1070 mm/3.52 ftWeight with mowing deck 216 kg/475 lbs 219 kg/481 lbsDistance between axles 860 mm/2.81 ft 850 mm/2.81 ftWheel track front: 720 mm/2.36 ft 715 mm/2.34 ft

rear: 620 mm/2.04 ft 630 mm/2.06 ftTyre dimensions 16 x 7.5 x 8 16 x 7.5 x 8Air pressure, front and rear 60 kPa (0.6 kp/cm2/8.5 PSI) 60 kPa (0.6 kp/cm2/8.5 PSI)Max permitted slope 15° 15°

Engine

Make Briggs & Stratton Briggs & Strattonmodel 215907 model 282H070110E2

Power 7.7/10.5 kW/hp 9.2/12.5 kW/hpDisplacement 344 cm3 344 cm3

Fuel at least 85 octane unleaded at least 85-octane unleadedTank volume 7.2 litres/7.6 USqt 7.2 litres/7.6 USqtOil synthetic SAE 5W/30 or SAE 10W/30 SAE 5W/30 or SAE 10W/30

class SJ-CF class SJ-CFOil volume 1.4 litres/1.5 USqt 1.4 litres/1.5 USqtStart Electric start Electric start

Noise emissions and mowing width

Measured sound power 100 dB(A) 100 dB(A)Guaranteed sound power 100 dB(A) 100 dB(A)Mowing width 850 mm/33.5" 850 mm/33.5"

Electrical system

Type 12 V, negative grounded 12 V, negative groundedBattery 12 V, 24 Ah 12 V, 24 AhMain fuse Flat-pin mounting 15 A Flat-pin mounting 15 ASpark plug Champion QC12YC Champion QC12YCElectrode gap 0.75 mm/0.030" 0.75 mm/0.030"

Transmission

Make Peerless MST 205 Tuff Torq K46Oil - SAE 10W/30, class SF-CCNumber of forward gears 5 -Number of reverse gears 1 -Forward speed 0-9 km/h 0-9 km/hReverse speed 0-6 km/h 0-6 km/h

TECHNICAL DATA

English – 45

TECHNICAL DATA

Dimensions FR 2113 MA FR 2116 MA

Length without mowing deck 2010 mm/6.58 ft 2010 mm/6.58 ftLength with mowing deck 2220 mm/7.29 ft 2220 mm/7.29 ftWidth without mowing deck 880 mm/2.89 ft 880 mm/2.89 ftWidth with mowing deck 1000 mm/3.29 ftHeight 1070 mm/3.52 ft 1060 mm/3.48 ftWeight with mowing deck 226 kg/497 lbs 229 kg/504 lbsDistance between axles 850 mm/2.79 ft 855 mm/2.8 ftWheel track front: 720 mm/2.36 ft 715 mm/2.34 ft

rear: 630 mm/2.06 ft 625 mm/2.05 ftTyre dimensions 16 x 7.5 x 8 16 x 7.5 x 8Air pressure, front and rear 60 kPa (0.6 kp/cm2/8.5 PSI) 60 kPa (0.6 kp/cm2/8.5 PSI)Max permitted slope 15° 15°

Engine

Make Briggs & Stratton Briggs & Strattonmodel 282H070110E2 model 282H070110E1

Power 9.2/12.5 kW/hp 15.5 kW/hpDisplacement 344 cm3 465 cm3

Fuel at least 85 octane unleaded at least 85-octane unleadedTank volume 7.2 litres/7.6 USqt 7.2 litres/7.6 USqtOil synthetic SAE 5W/30 or SAE 10W/30 SAE 5W/30 or SAE 10W/30

class SJ-CF class SJ-CFOil volume 1.4 litres/1.5 USqt 1.4 litres/1.5 USqtStart Electric start Electric start

Noise emissions and mowing width

Measured sound power 98 dB(A) 100 dB(A)Guaranteed sound power 100 dB(A) 100 dB(A)Mowing width 900 mm/35.5" 1030 mm/40.5"

Electrical system

Type 12 V, negative grounded 12 V, negative groundedBattery 12 V, 24 Ah 12 V, 24 AhMain fuse Flat-pin mounting 15 A Flat-pin mounting 15 ASpark plug Champion QC12YC Champion QC12YCElectrode gap 0.75 mm/0.030" 0.75 mm/0.030"

Transmission

Make Tuff Torq K46 Tuff Torq K46Oil SAE 10W/30, class SF-CC SAE 10W/30, class SF-CCNumber of forward gears - -Number of reverse gears - -Forward speed 0-9 km/h 0-9 km/hReverse speed 0-6 km/h 0-6 km/h

46– English

TECHNICAL DATA

In order to introduce improvements the specification and design are subject to alteration without priornotice.

Note that no legal demands whatsoever can be made with the support of the information in this operator’smanual.

Only use original spare parts with repairs. The use of other parts invalidates the warranty.

When this product is spent and is no longer used it should be returned to thedealer or other authority for recycling.

Mowing deck

Type Triple blade cover Double blade cover Triple blade coverwith rear ejection Mulching 900 mm Combi 1030 mm

Mowing width 850 mm/33.5" 900 mm/35.5" 1030 mm/40.5"Cutting heights9 positions 40-90 mm/1 9/16" - 3 9/16" 45-95 mm/1 3/4" - 3 3/4" 45-95 mm/1 3/4" - 3 3/4"Blade diameter 304 mm/12" 480 mm/19" 390 mm/15 3/8"

English – 47

EU-DECLARATION OF CONFORMITY

EU declaration of conformity (Only applies to Europe)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares under sole responsibility that theRider Jonsered FR 2111, FR 2113 A, FR 2113 MA, FR 2116 MA, from 2002’s serial numbers and onwards (the yearis clearly stated in plain text on the rating plate with subsequent serial number), complies with the requirements of theCOUNCIL’S DIRECTIVES:

- of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.- of May 3, 1989 ”relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements.- of May 8, 2000 ”relating to the emission of noise to surroundings” 2000/14/EC.Information regarding noise emissions and the mowing width, see the Technical Data.

The following harmonised standards have been applied: EN292-2, EN836.

The registered body 0404, SMP Svensk Maskinprovning AB, Fyristorgsgatan 3, SE-754 50 Uppsala, Sweden hasissued the report with number 01/901/001, 01/901/002, 01/901/003, 01/901/004 regarding the assessment ofconformity according to annex VI to the COUNCIL’S DIRECTIVE of May 8, 2000 ”relating to the emission of noise tosurroundings” 2000/14/EC.

Huskvarna January 3, 2002

Roger Andersson, Development Manager/Garden Products

48– English

Delivery service

1. Fill the battery with battery acid and charge for four hours.

2. Fit the steering wheel, towing eye and where applicable othercomponents.

3. Adjust the mowing deck:

Adjust the lifting springs (the weight of the mowing deck shouldbe 12-15 kg/26.5-33 lbs). Only applies to the Mulching unit.

Adjust the mowing deck so its rear edge is about 2-4 mm (1/8")higher than its front edge.

Adjust the mowing deck’s cutting height setting so that thecutting height limit is 5 mm (3/16") above the deck frame at thelowest cutting height.

4. Check that the right amount of oil is in the engine.

5. Check that the right amount of oil is in the transmission(not FR 2111).

6. Check and adjust the air pressure in the tyres (60 kPa/0.6 bar/8.5 PSI).

7. Connect the battery.

8. Fill the fuel tank and start the engine.

9. Check that the machine does not move in neutral (not FR 2111).

10. Check:

Driving forwards.

Reversing.

Actuating the blades.

Safety switch for the seat.

Safety switch for the lifting lever.

Safety switch for the hydrostat pedals/neutral position.

11. Check that engine revs max. 2950 rpm.

12. Inform the customer about:

The need and benefit of following the service schedule.

The need and benefit of leaving the machine forregular service.

The effects of maintenance on the machine’s second handvalue.

Application areas for Mulching.

13. Fill in the sales certificate, etc.

Delivery service has beencarried out.

No remaining notes.

Certified:

After the first 5 hours

1. Change engine oil.

Action Date, stamp, signature

SERVICE SCHEDULE

Date, stamp, signature

English – 49

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

SERVICE JOURNAL

Action Date, mileage reading, stamp, signature

50– English

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

SERVICE JOURNAL

Action Date, mileage reading, stamp, signature

English – 51

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

SERVICE JOURNAL

Action Date, mileage reading, stamp, signature

52– English

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

SERVICE JOURNAL

Action Date, mileage reading, stamp, signature

´®z*xzh¶6W¨

English – 53

2003W45´®z*xzh¶6W¨

108 89 07-26