제 10 장 advanced lithography - kocwcontents.kocw.net/kocw/document/2014/chungbuk/... ·...
TRANSCRIPT
-
- 1 -
제 10 장 Lithography II
1. Mask Technology
(1) 제작 방법
▢ hand-cut or machine cut artwork (rubi lith)• 보통 250 배율로 만들고 나서 2 단계를 거쳐 사진기
를 이용하여 축소시킴
• 해상력 > 4μm ▢ optical pattern generation• 직접 사진용 판에 최종 크기로 노광시킴 • 해상력 > 2μm ▢ e-beam pattern generator• 직접 감광막에 노광시킴.• 해상력 < 0.5μm
(2) 기본 mask 구조
Glass Blank Plate : chrome, Si, iron oxide
• Issues: - Blank: 빛의 투과성, 열 팽창, 표면의 평판도
- Plate: 패터닝, 내구성, 결함 농도
-
- 2 -
▢ Dark Field vs. Clear Field
-
- 3 -
2. Mask Aligner Technology
(1) Mask Aligner 종류
-
- 4 -
-
- 5 -
▢ Projection Printing 종류
-
- 6 -
3. Physical Limitations of Optics
(1) Diffraction (회절)
-
- 7 -
(2) Diffraction and Image Formation
▢ Abbe Theory of Image Formation
-
- 8 -
(3) Resolution
-
- 9 -
-
- 10 -
• Resolution- Printable Pminimum = sin
∵ The lens has to collect at least the n =1 diffracted beams to show any spatially varying
intensity on wafer.
∴ Resolution =
minsin
- Practically, resolution =
k1: a constant between 0.25 and 1, depending on
optics, resist, and process latitude. Typically k1 = 0.6
* Numerical aperture = sinθ
-
- 11 -
(4) Depth of Focus
-
- 12 -
• Depth of Focus λ4
= DoF - DoF cos θ = DoF ( 1 - cos θ )
여기서, c o s θ = 1 - 2 s in 2 ( θ2 ) ≈ 1 - 2 (NA2 )
2
∴ λ4
= D oFNA 2
2
∴ D oF = ± λ2 NA 2
실제적으로는, D oF = ± k λNA 2
-
- 13 -
4. Misalignment Error
• Use special alignment structures boxes within boxes, or crosses within crosses
• New layer aligned within layer below• Watch for 3 types of errors ① Thermal run-out
② Translational error
③ Rotation errors
-
- 14 -
▢ Alignment Marks in Mask• Each level has it own alignment mark• Generally "plus" sign type• Two types of alignment mark
-
- 15 -
▢ Alignment Marks: Level to level• Next level must be able to align to level below• Upper level marks is wider by minimum geometer on each side
• Light field centers upper level in lower• Dark field centers lower level in upper• More complicated when mix differ level types
-
- 16 -
• Total Overlay Tolerance
σi = std. deviation of overlay error for ith masking
step
σtotal = std. deviation for total overlay error
* Layout design-rule spec. should be > σtotal
-
- 17 -
5. Super Resolution Techniques
(1) Phase Shift Mask
-
- 18 -
(2) OPC(optical proximity correction)
- 광학 근접 보정
- 이미지 능력을 향상시키기 위해 인접한 하위 해상도
형상을 변형시킨 모양들을 이용한 기술 (Square의
contact hole은 circle 로 되기 때문에 정확한 square를
만들기 위해 additional geometry를 사용한다)
-
- 19 -
(3) Off-Axis Illumination
-
- 20 -
6. Next Generation Lithography
XRL: X-Ray Lithography
EPL: Electron Projection Lithography
IPL: Ion Projection Lithography
-
- 21 -
(1) EUV (Extreme Ultra-Violet) Lithography
▢ 특성- 극자외선 리소그래피는 차세대 기술로써 throughput
손실 없이 최소 선폭을 30nm로 향상시킬 수 있음
- 극자외선 파장 : 10~14nm
▢ 광원 - Discharge-produced Sn Plasma: 13.5 nm
- Laser-produced Xe Plasma: 11.4 or 13.5 nm
▢ 노광 시스템- 극자외선은 렌즈를 통과할 수 없으므로 거울의 반사를
이용하여 상을 축소시키고 또한 이러한 반사율을 극대화
하기 위하여 다층 박막을 이용함. 즉, 극자외선을 마스크
에 반사시켜 웨이퍼 위에 패턴 형성
-
- 22 -
▢ 극자외선 리소그라피 장치의 개략도
* paraboloid: 포물면, ellipsoid: 원면
▢ 문제점- 극자외선은 모든 물질에 강하게 흡수가 잘 된다. 따라
서 리소그래피 공정 시 챔버 안은 진공 상태를 유지해야
한다.
- Mask blank는 방출되는 파장 (10~14nm)의 반사도를
최대화하기 위해 다층으로 코팅을 해야만 한다.
-
- 23 -
(2) X-Ray Lithography
▢ 특성• 파장: 5 - 20 Å • Advantages
- High resolution: 0.1 μm 이내
- Large DoF ( > ±10 μm )
- Wide field size: 50 x 50 mm2
- Single layer resist processes
▢ 노광 장치① Proximity Exposure System
② Projection Exposure System
-
- 24 -
▢ 문제점• Mask fabrication• Large optical facilities • High accuracy alignment system• High sensitivity resist material
▢ Mask Fabrication Processes
-
- 25 -
(3) E-Beam Lithography
▢ 특성• 파장
(e.g. λ = 0.07 Å with 30 KV)
• Advantages- High resolution ~ 1 nm
organic resist PMMA ~ 7 nm
inorganic resist, b.v. AlF3 ~ 1-2 nm
- Large DoF ( > ±10 μm )
- Chip size free - Maskless
• 문제점- Low throughput -> cell/block exposure
- Proximity effect/ charge-up
- High sensitivity/ high resolution resist
▢ Exposure System Schematics
-
- 26 -
▢ Inter and intra proximity effects in e-beam exposure
-
- 27 -
▢ Cell Projection System
-
- 28 -
(4) Immersion Lithography
• liquid with index of refraction n>1 is introduced between the imaging optics and the wafer
• λliquid = λair /n• With water, the index of refraction at = 193 nmis 1.44, improving the resolution significantly
-
- 29 -
(5) Ion Beam Lithography
• 이온 빔 리소그래피는 광, X-선 또는 전자 빔 리소그래피 기술보다 고해상도를 갖는다. 왜냐하면 이온은 높은
질량을 가지며 따라서 전자 보다 덜 산란이 된다. 가장
중요한 적용은 광 리소그래피를 위한 마스크의 repair이
다
Trajectories of 60-keV H+ ions traveling through PMMA into
Au, Si and PMMA
• ion beam의 산란은 매우 적고 Si의 경우 back scattering이 거의 없다 (Au 경우 아주 적음)
• 그러나 ion beam litho는 ion beam를 broadening하는 space charge 효과가 생길 수 있다
-
- 30 -
• 여러 가지 lithography 기술들의 상호 비교