occupancy based fan speed controller
DESCRIPTION
temperature and occupancy based fan speed controllerTRANSCRIPT
![Page 1: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/1.jpg)
OCCUPANCY AND TEMPERATURE BASED FAN CONTROLLER
SUBMITTED BY:SHARAFAT HUSSAINANURAG MISHRAVINAY KUMAR MISHRA
UNDER THE GUIDANCE OF Mrs. VANDANA CHAUHANPROJECT COORDINATORMr. PRAVEEN KUMAR
![Page 2: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/2.jpg)
OVERVIEW
This project is used to regulate the fan speed based on number of occupant and turn the fan off when the temperature is below the set temperature .A bulb is also provided with the circuit, it turns on when the number of occupant is greater than zero.
The complete project is divided into three PCB 1. Temperature controller circuit2. Timer and counter circuit3. Speed regulator circuit
We will describe each with block diagram, description of components and circuit diagram
![Page 3: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/3.jpg)
PCB NO.1Temperature controller circuit
Components
1. AT89C52 Microcontroller --12. ADC0804 LCN --13. Temperature Sensor LM35--14. 16*2 LCD Display --15. Voltage Regulator L7805 --16. Resistors --97. Capacitors --58. Diodes --3 9. Transistor TIP120 --210. Crystal Oscillator 12MHz --111. Electric Fan 12 V --112. DC6V RELAY --113. LED --214. BUTTONS --4
![Page 4: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/4.jpg)
PCB-1BLOCK DIAGRAM-1
![Page 5: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/5.jpg)
PCB-1WORKING
HOW DO TEMPERATURE CONTROLLERS WORK?
To accurately control process temperature without extensive operator involvement, a temperature control system relies upon a controller, which accepts a temperature sensor LM35 as input. It compares the actual temperature to the desired control temperature, or set point, and provides an output to a control element. The controller is one part of the entire control system, and the whole system should be analyzed in selecting the proper controller.
ON/OFF CONTROL
An on-off controller is the simplest form of temperature control device. The output from the device is either on or off, with no middle state. An on-off controller will switch the output only when the temperature crosses the set point. For heating control, the output is on when the temperature is below the set point, and off above set point. Since the temperature crosses the set point to change the output state, the process temperature will be cycling continually, going from below set point to above, and back below.For the circuit to turn off or on a electronic DC6V relays is used.
![Page 6: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/6.jpg)
PCB-1DESPRIPTION OF COMPONENTS
ADC0804
FEATURES• 80C48 and 80C80/85 Bus Compatible - No Interfacing Logic Required• Conversion Time . . . . . . . . . . . . . . <100μs• Easy Interface to Most Microprocessors• Will Operate in a “Stand Alone” Mode• Differential Analog Voltage Inputs• Works with Bandgap Voltage References• TTL Compatible Inputs and Outputs• On-Chip Clock Generator• Analog Voltage Input Range (Single + 5V Supply) . . . . . . . 0V to 5V• No Zero-Adjust Required• 80C48 and 80C80/85 Bus Compatible - No Interfacing Logic Required
![Page 7: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/7.jpg)
TEMPERATURE SENSOR LM35The LM35 series are precision integrated circuit temperature sensors, whose output voltage is linearly proportional to the Celsius (Centigrade) temperature.
LM35 INTERFACING WITH ADC0804 LM35
![Page 8: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/8.jpg)
MICROCONTROLLERThe AT89S52 is a low-power, high-performance CMOS 8-bit microcontroller with 8K bytes of in-system programmable Flash memory.
![Page 9: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/9.jpg)
POWER SUPPLYFULL WAVE RECTIFIER
![Page 10: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/10.jpg)
INTERFACING THE LCD WITH THE MICROCONTROLLERS
![Page 11: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/11.jpg)
INTERFACING OF A ADC0804 WITH A 8051 MICROCONTROLLER
![Page 12: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/12.jpg)
CIRCUIT DIAGRAM-1
![Page 13: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/13.jpg)
PCB NO.2COUNTER AND TIMER CIRCUIT
COMPONENTS1. IR Transmitter Module 2. IR Receiver Module 3. IC 5554. Up down Counter5. Seven Segment Display6. Seven Segment decoder7. 4 Bit Comparator8. Relay
![Page 14: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/14.jpg)
PCB-2BLOCK DIAGRAM
![Page 15: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/15.jpg)
WORKING OF PCB-2Infrared receiver module is used to receive the infrared signal transmitted by transmitter. In this project we use two infra red sensors. Both connected in the door. Two photodiode’s are also connected to the receiver circuit to detect the infra red signal. Both the infra red sensor is connected to the IC 555 as a monostable timer In attach with the sensor and 555 we use one up down counter circuit. Up down counter increment and decrement the input pulses and display it on the seven segment display. One logic circuit to compare the total number of person in the room is also involved in this project. For this purpose we use ic 7485 4 bit binary comparator to compare the total number of person in the room. One relay driver circuit to interface the main lights or fan with this unit. Relay provide a high voltage to the fan and lights for proper working
![Page 16: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/16.jpg)
PCB-2DESPRIPTION OF COMPONENTS
INFRA RED SENSOR
![Page 17: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/17.jpg)
IC 555The 555 timer IC is an integrated circuit (chip) used in a variety of timer, pulse generation, and oscillator applications. The 555 can be used to provide time delays, as an oscillator and as a flip-flop element. Derivatives provide up to four timing circuits in one package. In this circuit it works as monostable.
MONOSTABLE MODE
In this mode, the 555 functions as a "one-shot" pulse generator
![Page 19: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/19.jpg)
UP/DOWN COUNTERA counter that can change state in either direction, under the control of an up/down selector input, is known as an up/down counter. When the selector is in the up state, the counter increments its value. When the selector is in the down state, the counter decrements the count.
IC555 WITH 74192PIN CONFIGURATION
![Page 20: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/20.jpg)
7447 WITH SSD
![Page 21: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/21.jpg)
PCB-2CIRCUIT DIAGRAM
![Page 22: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/22.jpg)
PCB-3SPEED REGULATOR CIRCUIT
In this project we have used a DC6V Motor, in order to control its speed based on the number of occupants, We change the armature current by changing the armature voltage. The up/down counter in PCB-2 is connected to a 4-bit magnitude comparator and in turn connected to a another a-bit comparator. It compare the counter values a gives voltage to ic358 accordingly.
COMPONENTS
1. 7485 Magnitude comparator2. 358 dual op-amp3. Transistor4. Resistors5. LED6. Capacitors
![Page 23: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/23.jpg)
BLOCK DIAGRAM OF PCB-3
![Page 24: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/24.jpg)
DESPRIPTION OF COMPONENTS 7485 Magnitude Comparator
DESCRIPTIONThe 74F85 is a 4-bit magnitude comparator that can be expanded to almost any length. It compares two 4-bit binary, BCD, or other monotonic codes and presents the three possible magnitude results at the outputs. The 4-bit inputs are weighted (A0–A3) and (B0–B3) where A3 and B3 are the most significant bits.
![Page 25: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/25.jpg)
OP-AMP ICFeatures1. Available in 8-Bump micro SMD chip sized
package,2. Internally frequency compensated for
unity gain3. Large dc voltage gain: 100 dB4. Wide bandwidth (unity gain): 1 MHz
(temperature compensated)5. Wide power supply range: Single
supply:3V to 32V:dual supplies:±1.5V to ±16V
6. Very low supply current drain (500 μA)essentially independent of supply
7. Low input offset voltage: 2 mV8. Input common-mode voltage range
includes ground9. Differential input voltage range equal to
the power supply voltage10. Large output voltage swing
![Page 26: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/26.jpg)
PCB-3CIRCUIT DIAGRAM
![Page 27: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/27.jpg)
THANK YOU
“There is neither this world nor the world beyond nor happiness for the one who
doubts.” -BHAGAVAD GITA
![Page 28: occupancy based fan speed controller](https://reader035.vdocuments.site/reader035/viewer/2022081413/5461ac7aaf79597c138b465c/html5/thumbnails/28.jpg)