objectives
DESCRIPTION
Objectives. Blower door and duct bluster measurements - Theory and lab. Infiltration/Leakage Measurements (Calibrated Fans). Flow going through fan is calibrated to pressure rise across fan If you measure pressure, than you know flow Requires very smooth inlet and outlet conditions - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/1.jpg)
Objectives
Blower door and duct bluster measurements
- Theory and lab
![Page 2: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/2.jpg)
2
Infiltration/Leakage Measurements
(Calibrated Fans)• Flow going through fan is calibrated to
pressure rise across fan– If you measure pressure, than you know flow
• Requires very smooth inlet and outlet conditions
• Often have to restrict flow to get measurable pressure signal for low flows
• Examples:– Blower door and Duct Blaster
2
![Page 3: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/3.jpg)
Fan Pressurization
• In 1970s, smoke evacuation fans used to find air leakage
1. Install blower door
2. Use fan to create artificial pressure difference between inside and outside
3. Use smoke stick (or cigarette, etc.) to visualize flow patterns.
4. Seal leaks
![Page 4: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/4.jpg)
![Page 5: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/5.jpg)
![Page 6: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/6.jpg)
Quantitative Blower Door
• How many points should you measure?
• How can you estimate uncertainty?
http://www.energyconservatory.com/products/products1.htm#pd16
![Page 7: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/7.jpg)
Test Data
• 1000 ft2 house, 10 ft high ceilings
• Two-point test– 1688 CFM at 51 Pa– 1048 CFM at 24.5 Pa
• What is ACH50 (λ50), C?
![Page 8: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/8.jpg)
Answers
• λ50= 1 ACH
• C = 131.07 CFM/Pan
• n = 0.65
![Page 9: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/9.jpg)
Reporting blower door data
• Flow (or air exchange rate) at a given pressure
• Equivalent Leakage Area
– What are dimensions of c?
![Page 10: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/10.jpg)
Comment
• Blower doors do not measure air exchange rate– Why not?
• What do they measure?
![Page 11: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/11.jpg)
11
Blower Door Misc. • All windows and doors to outside closed
– Why? What about buffer spaces?
• HVAC off• Hard to do on windy days • Watch out for buckling linoleum floors and
fireplaces• Flow direction change/ring change can be
discontinuous• Remember to record before and after reference
pressures with fan covered
11
![Page 12: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/12.jpg)
More Blower Door Tests• Measure component leakage
– What fraction of leakage is due to a certain component?
– Tape off component and repeat test• What are issues with this approach?
• Series leakage paths– Air leaks to attic and then to crawlspace and
then to outside
![Page 13: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/13.jpg)
Residential Component Leakage
Component Range Average
Walls 18-50% 35%
Ceilings 3-30 13
Windows/Doors 6-22 15
Fireplaces 0-30 12
HVAC 3-28 18
Other Vents 2-12 5
![Page 14: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/14.jpg)
Duct Leakage
• Responsible for enormous energy losses (20-30% is not uncommon)– Comfort– Outdoor air pollution– Contaminant spread
![Page 15: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/15.jpg)
Duct Leakage
• Excluding registers, grills, diffusers– Ducts leak to the inside– Ducts leak to the outside (mostly an American
problem)– Ducts leak on the supply (positive pressure) side– Ducts leak on the return (negative pressure)
side
• What are we concerned from the perspective of:– Energy?, Indoor air quality? Comfort?
![Page 16: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/16.jpg)
Duct Leakage Method 1
• Blower door subtraction• Two successive blower door tests
1. Normal2. With duct registers sealed (with tape)
• Difference is total duct leakage• Is this supply, return, or total?• Is this inside, outside, or both?• Problems and limitations?
![Page 17: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/17.jpg)
Duct Leakage Method II
• Duct pressurization
• Tape registers
• Use Duct Blaster (calibrated fan) to do a “blower door” test of the ducts
• Is this supply, return, or total?
• Is this inside, outside, or both?
• Problems and limitations?
![Page 18: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/18.jpg)
![Page 19: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/19.jpg)
Duct Pressurization Test Extension
• How do you measure exterior leakage?
• How do you measure supply and return leakage separately?
• How do you measure duct leakage at operating conditions?
![Page 20: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/20.jpg)
![Page 21: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/21.jpg)
21
Reporting Duct Leakage
• Are we interested in absolute amount of leakage or relative?– If relative, relative to what?
• ASHRAE Standard 152 defines:– αs supply leakage fraction– αr return leakage fraction
21
![Page 22: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/22.jpg)
22
Air Handler Flow Measurement
• Often need to know flow through air handler– Historically many methods, all problematic:
• Non-uniformity of flow (i.e., very turbulent)
• True Flow Plate– Specialized type of orifice– Replaces filter– Gives air handler flow
• Pressure correction22
![Page 23: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/23.jpg)
Other Duct Leakage Testing Methods
• Nulling test– Measures duct leakage at operating
conditions– Also measure air handler flow– Very intensive to set-up and also sensitive to
wind
• Delta-Q test– Only uses a blower door and does not require
taping registers– But mathematically problematic
![Page 24: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/24.jpg)
24
Nulling Test
• Step 1: Install Duct Blaster fan in doorway to building, turn on air handler and zero* out any pressure imbalance– What does the flow through the fan equal?– Why is this test sensitive to wind?– Under what conditions will this test fail?
24
![Page 25: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/25.jpg)
25
Nulling Test (cont.)
• Step 2: Second Duct Blaster is installed in HVAC system, return side sealed off, air handler fan turned on, and air flow rate is adjusted to match supply plenum pressure under normal conditions
• Step 3: Step 1 is repeated– What is flow through Duct Blaster installed in
door this time?
25
![Page 26: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/26.jpg)
Summary of Nulling test • Use a Duct Blaster as envelope fan to “null out”
change in envelope pressure caused by unbalanced duct leakage
• First with normal operation –unbalanced leakage• Second with return isolated and a Duct Blaster
assisting the AH fan so there is no return leakage –supply leakage
• Difference is return leakage• Measures leakage directly –thought to be accurate• Very sensitive to wind
![Page 27: Objectives](https://reader030.vdocuments.site/reader030/viewer/2022032805/568133f3550346895d9ae588/html5/thumbnails/27.jpg)
General Comments about Fan Tests
• Buildings are complicated, go slowly and methodically– Practice/experience are key– Practical matters (HVAC turned on, someone
stepped on a tube, wind, etc.) are very important
• Cardboard and tape are useful research tools/skills