nissan juke 2wd - towbars direct
TRANSCRIPT
ISTRUZIONI DI MONTAGGIOFITTING INSTRUCTIONS
INSTRUCTIONS DE MONTAGEMONTAGEANLEITUNG
INSTRUCCIONES DE MONTAJE
DISPOSITIVO DI TRAINO TIPOTOWING BRACKET TYPEDISPOTIF DE REMORQUAGE TYPEANHAENGEVORRICHTUNG TYPDISPOSITIVO DE CAREO TIPO
26026/C
PER AUTOVEICOLIFOR CARSPOUR AUTOSFUR KRAFTAHRZEUGEPARA AUTOVEHICULO
NISSAN JUKE 2WD
TYPE F15 2010 CLASSE E TIPO DI ATTACCOCLASS AND HITCH TYPECLASSE ET TYPE DE CROCHETKLASSE UND BEFESTIGUNGSARTCLASES DE ACOPLAMIENTO
OMOLOGAZIONEHOMOLOGATIONHOMOLOGATIONZULASSUNGAPROBACION
CARICO VERTICALE MAXS VALUEMASSE VERTICALE MAXIMUMZUL. STUETZLASTCARGA MAX. VERTICAL
F e3 00 – 7591(DIR. 94/20/CE)
S = kg 80
VALORE DD VALUEVALEUR DD WERTVALOR D
D = 8,5 kN
COPPIA DI SERRAGGIO PER VITI (8.8):TORQUE SETTINGS FOR NUTS AND BOLTS (8.8):
COUPLE DE SERRAGE POUR VIS (8.8):SCHRAUBENANZUGSMOMENT (8.8):
MOM. DE PRESION PARA TORNILLOS Y TUERCAS (8.8):
Cod. 26026/C- Nissan Juke -
v. 1.0 01/01/2011 P. 1 / 6
8,5 kN
M6 = 10 Nm M8 = 25 NmM10 = 55 Nm M12 = 85 NmM14 = 135 Nm M16 = 200 Nm
Tel. +39 075.5280260Fax +39 075.5287033Via Pizzoni 37/3906132 PerugiaITALY
SAFETY INSTRUCTIONS
Make sure that the towbar is suitable for the vehicle before starting the installation.
For safety, all work involving towbar installation (incl. electrical components) must be undertaken by skilled technicians.
Damaged components must be replaced with manufacturer’s spares and fitted by qualified staff.
It is forbidden to make any modification or structural repair to towing assembly.
The towball must be kept clean and lubricated. For added safety, his diameter (50 mm) must be checked at regular intervals. If the towball measures less than 49 mm after selected readings across the diameter, the towball must be replaced with a new one.
After 1000 km of towing, check torque settings for nuts and bolts, in accordance with the table.
Umbra Rimorchi cannot be held responsible for any defects in the product caused by fault or by any injudicious use whatever of the user or a person he is liable for.
Cod. 26026/C- Nissan Juke -
v. 1.0 01/01/2011 P. 2 / 6
FITTING INSTRUCTIONS
26026/C
Remove the eventual protection mastic from areas which may come in contact with the tow bar assembly and paint areas with anti-rust paint. The holes for fixing the structure are existing.
1. Remove bumper, the plastic protection under the bumper and then discard the reinforcement bar.
2. Insert the side-arms “A” inside the chassis rails referring to holes “1”.3. Locate items ”B” outside the chassis rails referring to holes “1” and “2”. Insert the
screws just in position “1”.4. Locate items “C” inside the chassis rails referring to holes “2” insert the screws
then tighten interposing large washers.5. Locate item “D” between the two side-arms “A”,referring to holes “3” and “4” then
tighten.6. Tighten all bolts and nuts as per torque settings.7. Connect the wiring to the socket.8. Cut the plastic protection as showed.9. Re-fit the plastic protection and bumper.
DISAPPEARING SOCKET
Cod. 26026/C- Nissan Juke -
v. 1.0 01/01/2011 P. 3 / 6