new 700 series lexion training presentation.ppt [read-only] · 2020. 6. 18. · 2 9/20/2013 700...
TRANSCRIPT
700 Series Lexion Training
CEBIS Training
9/20/2013 700 Series CEBIS Training 2
700 Series CEBIS – Major Topics
� General Navigation of Cebis
� Learning Crops
� Learning Speeds
� Learning Header Heights
� CAC Settings
� Making Adjustments to Settings
� Using Multifunction Handle.
� Calibrate Yield Monitor – Quantimeter
700 Series CEBIS – General Navigation
9/20/20133 700 Series CEBIS Training
Menu Icons Header Height / Float
Information Box
Tailings Information
Rotor Loss Monitor
Sieve Loss Monitor
Operator Selected Info
Quantimeter Data
Speed / Gear / 2 or 4
wheel drive
700 Series CEBIS – Learning Crops
9/20/20134
• Highlight “Wheat Head” icon – “ok”
• Hit “ok” to select “crop data” – Hit “ok”
• Scroll to crop that you want – “ok”
• It will ask to “Load LEX settings”? – “ok”
• (Must have combine / separator running at full throttle)
700 Series CEBIS Training
700 CEBIS – Learning Speeds
• Go to the “Combine” icon – “ok”
• Go to “speeds” – “ok”
• (must have combine / separator running full throttle)
• Hit “ok” to start learning speeds – you will be in screen #3 you must learn each speed
separately in the list
• Keep hitting “ok” to learn then rotate to the
next speed and hit “ok” on that one till end
#1
#2
#3
700 CEBIS – Learning Header Heights
• Go to “Header” icon – “ok” – Hit “ok” on the header again in the second menu
• Go to “ Front attachment height” – “ok”
• Go to “screwdriver” icon – “ok” to start learning
• It will say “Raise front attachment” – Must hold the button on Mutli-fuction handle until it tells
you to “Lower front attachment”
• Same thing on Lowering – wait for screen
9/20/20136 700 Series CEBIS Training
700 Series CEBIS – Adjusting Header Heights
• Two ways to adjust header heights
• #1 – Move head to desired height and hold the right side of button until beep
• #2 – Use the “Hot Key” to select header and then just rotate knob to adjust – Must have a
height selected in order to adjust it.
Hot Key
Screen
Hot Key Knob
and Selector
700 Series CEBIS – CAC Settings
• CAC = Claas Auto Contour
• Start at the “Header” Icon – “ok” --- “Header” icon again – “ok”
• “Gauge” icon – “ok”
• “CAC” icon – “ok” ---- This will allow you to set these 5 settings now – Usually “Cutting
Height adjustment” and “Lateral levelling” are around “0”
• Fast manual raising / lowering usually work best when at “50”
• The last one is “return to height” – This one usually works well about “10”
9/20/20138 700 Series CEBIS Training
700 Series CEBIS – Making Adjustments to Settings
• Speed adjustment on a Lexion is very simple – Simply turn the rotary dial to the desired
component and then use the knob to make speed adjustments
9/20/20139 700 Series CEBIS Training
700 Series CEBIS – Using Multi-function Handle
• The Multi-function handle has many fuctions associated with it here is a brief descrption.
9/20/201310
Auto – Pilot activation switch
Unloading auger swing OUT
Unloading auger swing IN
Header STOP!
Reel Up – Down – In – Out -
Also controls Deck Plates
Auto Contour Activation
Pre-Set Height Activation
Manual Header Raise
Manual Header Lower
Unloading system Start and Stop
Front of handle – Manual tipping of header – or -
flex or rigid on flex head
700 Series CEBIS Training
700 Series CEBIS – Quantimeter Calibration
• Calibrating the Quantimeter is very easy to do
• Select the “Wheat” icon – “ok”
• Select the “Scales” icon – “ok”
• Select the “Scales” icon – “ok”
• Hit “ok” to select “status” – turn to “on” – hit “ok”
• Gather a sample with the combine
• Turn “Status” to “off”
• Divide lbs by 2204 to get tons
• -or- divide by test weight to get bushels
• Enter the tons / bu into
“Crop yield weighed”
• You do not have to do several samples
quantimeter does not require it.
9/20/201311 700 Series CEBIS Training
#1
#2
#3
700 Series CEBIS – Maintenance Reminders
• To reset the maintenance reminders you first start at the “wrench” icon – “ok”
• Go to the first icon – “ok”
• Go to the third icon – “ok”
• Highlight the reminder you want to reset and change it to “Yes” – “ok”
9/20/2013 Presentation Title12
#1
#2
#3
#4