W.O. # _____________________________________________DATE _______________________________________________MODEL ____________________________________________TECHNICIAN SIGNATURE ______________________________P.I.N. _________________________ HOURS ______________

CUSTOMER NAME ____________________________________ ADDRESS ___________________________________________CITY, STATE, ZIP _____________________________________PHONE _____________________________________________CUSTOMER SIGNATURE _______________________________

2300 AND PRIOR COMBINE INSPECTION

PM-14338Rev 3/09

CASE IH CUSTOMIZED MAINTENANCE INSPECTION CHECKLISTITEM # COMMENTS

Safety equipment1. Seat Belt2. Warning/Flashers, turn signals, beacons3. Decals, SMV4. Horn, back-up alarm5. Turn brakes and pedal interlock6. Feeder lift safety lock7. All shields in place8. Reflectors9. Mirrors

feeder HouSing10. FRT Feeder Chain Slats & Links11. FRT Upper Sprocket Strippers12. FRT Feeder Chain Drive Sprockets13. FRT Feeder Door Seal14. FRT Feeder Drum Stops, Pivot Area, Brgs.15. FRT Clean & Adjust Slip Cover16. FRT Feeder Chain Tension17. FRT Safety Stand18. CAB Feeder Reverser/Operational

rotor aSSembly19. FRT Impeller Blades & Wear Bars20. FRT Rotor Front Bearing & Casting21. LS Rasp Bars22. LRS Rear Rotor Separator Bars & Supports23. LRS Interrupters & Spike Bars/Supports24. FRT Transition Cone & Vanes25. TOP Torque Sensing Limit Pulleys (free oper.)26. TOP Jack Shaft Bearings/Speed Adjustor Motor27. TOP Cam Bearing, Spring & Yoke For Wear

rotor Cage/ConCaveS/grateS28. LS Remove/Inspect/Clean Concaves29. LS Remove/Inspect/Clean Grates30. LS Check Adjuster & Anchor31. LRS Check Rotor Cage: Crack or Distortion32. LS Check Vanes

auger bed33. LS Auger Shaft Alignment34. BAC Auger Drive Gear Mesh35. FRT Front Clean Out Door Seal36. LRS Material Build-Up: Auger Bed/Grain Pan37. LS Auger Bed Grain Spreaders (Paddles)38. FRT Auger Bed Front Bearing

bloCkSCHaffer/SHoe SieveS39. BAC Accumulation: Material Between Fingers40. BAC Cracks, Warpage or Misalignment41. LRS Check Seals and Hanger Bushings42. BAC Check Wing Nut Friction Adjustment43. BAC Sieve Grain Pan: Bent/ Missing Fingers

Cleaning fan44. LRS Fan Blade to Housing Clearance45. LRS Fan Bleed Cut-Off Point46. LRS Fan Blades47. RS Drive Pulley48. LS Transducer Positioning & Wire Routing

This information is only for the purpose of suggesting possible repair or treatment of equipment. Any remedy will be limited to the amount of the inspection fee. Dealer makes no expressed or implied warranties, and disclaims any incidental or consequential damages.* Adjust valve lash if Operator Manual scheduled interval has been reached at time of inspection.

diSCHarge area 49. BAC Discharge Beater: Cracks, Wear Pan Adj.50. BAC Straw Chopper: Blade Wear & Adj.51. BAC Straw Spreader: Worn/Missing Sprdr. bats52. BAC Straw Spreader: Drive Shaft Bevel Gears

grain/tailingS augerS/elevator53. RS Clean Auger Trough54. BAC Auger Flights for Cracks or Bending55. RS Elevator Flights, Sprockets & Chain56. RS Elevator Bearings57. TOP Elevator Heads for Wear58. RS Locking Collars, Drive Hubs, Set Screws59. RS Check/Adjust Slip Cover60. RS Tailings Elevator Chain Adjustment

grain tank/unloader SyStemS61. TOP Flight Ext. Correct On Cross- Leveling Auger62. TOP Unloading Drive Sprockets & Belts63. TOP Grain Tank, Leaks64. TOP Pos. 2 Lower Auger Covers - Even Unloaded65. TOP Upper Unloader Gear Box

eleCtriCal SyStem - Cab CHeCk66. Lights67. Turn Signals/Flashers68. Audible Alarms69. Sprdr./Feeder Clutch70. 2-Speed Hydrostat Motor

eleCtriCal SyStem - Cab CHeCk (Cont.)71. Variable Rotor Dr.72. Variable Fan Speed73. Chrg. Circuit Voltage74. Crnkg. Circuit Amp. Draw75. Electrical Fuel Pump76. Instrument Gauges/Lights77. Air Conditioning78. Reel Lift79. Reel Speed80. Header Lift81. Unloader Swing82. Auto Header Control83. Auto Feeder Cut-off84. Feeder Reverser85. Shaft Speed Monitor86. Grain Loss Monitor87. Neutral Start Switch

beltS and CHainS88. FRT Reel Pump Drive Belt89. FRT Header Jackshaft Drive Belt90. FRT Feeder Drive Belt91. TOP Separator Drive Belt92. TOP Rotor Variable Speed Drive Belt93. RS Fan Jackshaft Drive Belt94. RS Cleaning Fan Drive Belt95. RS Elevator Jackshaft Drive Belt96. RS Tailings Elevator Chain/Belt97. RS Grain Elevator Conveyor Chain98. LS Grain Tank Dist Drive Chain

A B C S A B C S A B C S A B C S

A CrITICAL – MUST rEPAIr

B OPErATIONAL – SIgNS Of wEAr

C OK

S PASSED INSPECTION - SErvICE PrOvIDED

1 of 2

W.O. # _____________________________________________DATE _______________________________________________MODEL ____________________________________________TECHNICIAN SIGNATURE ______________________________P.I.N. _________________________ HOURS ______________

CUSTOMER NAME ____________________________________ ADDRESS ___________________________________________CITY, STATE, ZIP _____________________________________PHONE _____________________________________________CUSTOMER SIGNATURE _______________________________

2300 AND PRIOR COMBINE INSPECTION

PM-14338Rev 3/09

CASE IH CUSTOMIZED MAINTENANCE INSPECTION CHECKLISTITEM # COMMENTS

beltS and CHainS (Cont.)99. LS Rr Tank Horizontal Auger Drive Chain100. LS Tank Unloader Drive Chain/Belt101. LS Unloader Clutch Belt102. RS Straw Chopper Drive Belt103. RS Straw Spreader Belt104. TOP Alternator/Fan Belt105. TOP A/C Compressor Belt106. LS Auxiliary Pump Drive Belt107. LS Leveling Pump Belt (70’s)108. Belt/Chain Shields Installed109. RS Header Drive Belt

engine110. TOP Coolant Level & Condition111. TOP Radiator Cap, Hoses, Connections112. TOP Clean Rad/Cooler/AC Cndsr/ Air Screen113. TOP Seal Around Rotary Screen/ Radiator Door114. TOP Fuel Tank Vent Clear115. LS Drain Water From Fuel Filter116. CAB Check High & Low Idle Speed117. TOP Check for Oil Leaks118. TOP Air Cleaner - Replace As Needed119. TOP Air Induction Test120. TOP Air Restriction Gauge121. TOP Inspect for Fuel Leaks122. TOP Check Eng. Compartment for Debris123. TOP Manifold, Muffler, Exhaust System124. TOP Aspirator Clear125. Engine Valve Latch Adjustment*

HydroStatiC drive126. LS Drive Pressure (stall test)127. CAB Inching Pedal Operation128. CAB Propulsion Control Lever Function Adjustment129. LS control Lever on Hydrostat for Wearing130. CAB Proper Shifting (effort & travel)131. RS Transmission Linkage for Wear and Adjustment132. LRS Drive Coupling for Wear133. CAB Proper Operation & Adjustment134. CAB Parking Brake Engages135. LRS Torque on Drive & Rear Wheel Lugs136. LRS Front & Rear Inflation Pressures137. BAC Guide Wheel Toe-In138. BAC Axle Pivot Areas for Cracks or Wear139. LRS Wheel Bearings (signs of seal leakage)

This information is only for the purpose of suggesting possible repair or treatment of equipment. Any remedy will be limited to the amount of the inspection fee. Dealer makes no expressed or implied warranties, and disclaims any incidental or consequential damages.* Adjust valve lash if Operator Manual scheduled interval has been reached at time of inspection.

HydrauliC SyStem140. lS Flow Rate Pumps (optional)141. LRS Hose & Line Connections, Seats/Packing142. CAB Operation - Insure All Valves Operating143. LS Header Lift High Pressure Filter144. LRS Hose & Pump Drive Belts

lubriCation levelS145. TOP Engine Oil146. RS Transmission147. LRS Final Drives148. TOP Hydraulic Reverser149. TOP PTO Drive Housing150. CAB Brake Fluid151. FRT FWD Gear Case152. LRS Guide Wheel Planetaries153. TOP Chopper Gr. Case154. ____________________________

fluid analySiS (validated tHru internet Site)155. Engine156. Transmission157. Final Drives158. Hydraulic159. Coolant (cc 2700 kit)160. PTO

A CrITICAL – MUST rEPAIr

B OPErATIONAL – SIgNS Of wEAr

C OK

S PASSED INSPECTION - SErvICE PrOvIDED

A B C S A B C S A B C S A B C S

2 of 2