neutral displacement relay - easun reyrolle limited

4
Neutral Displacement Relay B37 Description The relay comprises an attracted armature element fed via a rectifier and series resistor. It can be provided with either a fixed setting, or variable settings using a plug bridge. It has a minimum withstand of rated voltage continuously. Applications Neutral displacement detection can be applied in either of the following situations: To initiate an alarm for a single phase to earth fault on an insulated neutral system With such a system an earth fault on one phase will cause the voltages on the other 2 phases to rise with respect to earth and can reach the phase-to-phase voltage. The relay is to be connected across a secondary open delta winding of a 3 phase, 5 limb, voltage transformer which has the primary star point earthed. The voltage across the open delta secondary will rise from zero (or near zero depending on voltage balance) to as high as 3 times the secondary winding voltage per phase, e.g. 63.5V windings will produce up to 190V across the relay for a phase to earth fault close to the VT. B37 relays are rated to withstand this. To effect tripping on earthed neutral systems. When the upstream protection isolates an earth fault on a feeder on a delta connected HV side of a power transformer, the possibility remains of voltage rise on the two sound phases if the feeder continues to be energized from the LV side of the power transformer. The residual voltage of the feeder operates the relay at the transformer end of the HV feeder and the relay trips the LV circuit breaker. When the HV windings of the power transformer are delta connected, or star connected with the neutral not available, the neutral displacement protection requires the same equipment as described for the first application above. When the HV windings are star connected with the neutral available then the relay can be energized from a single phase voltage transformer having its primary connected between the neutral and earth. Either scheme can be supplemented by a definite time delay relay if required. Neutral Displacement Relay - B37

Upload: others

Post on 11-Feb-2022

8 views

Category:

Documents


0 download

TRANSCRIPT

Neutral Displacement Relay B37

The policy of Easun Reyrolle is one of continuous improvement and development. The company therefore reserves the right to supply equipment,

which may differ slightly from that described and illustrated in this publication.

Description

The relay comprises an attracted armature element fed via a

rectifier and series resistor. It can be provided with either a fixed

setting, or variable settings using a plug bridge. It has a minimum

withstand of rated voltage continuously.

Applications

Neutral displacement detection can be applied in either of the

following situations:

To initiate an alarm for a single phase to earth faulton an insulated neutral system

With such a system an earth fault on one phase will cause the

voltages on the other 2 phases to rise with respect to earth and

can reach the phase-to-phase voltage.

The relay is to be connected across a secondary open delta

winding of a 3 phase, 5 limb, voltage transformer which has the

primary star point earthed. The voltage across the open delta

secondary will rise from zero (or near zero depending on voltage

balance) to as high as 3 times the secondary winding voltage per

phase, e.g. 63.5V windings will produce up to 190V across the

relay for a phase to earth fault close to the VT. B37 relays are

rated to withstand this.

To effect tripping on earthed neutral systems.

When the upstream protection isolates an earth fault on a feeder

on a delta connected HV side of a power transformer, the

possibility remains of voltage rise on the two sound phases if

the feeder continues to be energized from the LV side of the

power transformer. The residual voltage of the feeder operates

the relay at the transformer end of the HV feeder and the relay

trips the LV circuit breaker. When the HV windings of the power

transformer are delta connected, or star connected with the

neutral not available, the neutral displacement protection requires

the same equipment as described for the first application above.

Ordering Information

• Rating

• Setting value or setting range

• Case style and size

Qualification

ISO 9001-2000

Note:

1. All dimensions are in mm

2. All dimensions are measured equidistant from centre line

3. Maximum depth of equipment inside panel : 200mm

PART CASE CUT OUT BEZEL

SIZE A B C D

01 2/3V 149.5 148 170 170

02 1V 221 148 243 170

Cutout Details When the HV windings are star connected with the neutral

available then the relay can be energized from a single phase

voltage transformer having its primary connected between the

neutral and earth.

Either scheme can be supplemented by a definite time delay

relay if required.

Cases

Single pole Modular size 4

Vedette 2/3V or 1V

Neutral Displacement Relay - B37

FACT

/B37

/08-

07/R

EV 1

®Easu

n R

eyro

lle-2

007 -

Easu

n R

eyro

lle,

the

Easu

n R

eyro

lle l

ogo a

nd a

ny

alte

rnativ

e ve

rsio

n t

her

eof

are

reg

iste

red t

rade

mark

s and s

ervi

ce m

ark

s of

Easu

n R

eyro

lle

Sales OfficesBangaloreEasun Reyrolle Ltd.#17/3 Arakere, Bannerghatta Road,Bangalore - 560 076, India.Tel: +91 80 26581023/3268Fax: +91 80 26580642Email: [email protected]

BhopalEasun Reyrolle Ltd.H.No.16, Essarjee HomesNear Gopal Nagar, Kalan RoadPiplani, Bhopal - 462 021, India.Telefax: +91 755 2684221Email: [email protected]

ChennaiEasun Reyrolle Ltd.6th Floor, Temple Tower, 672,Anna Salai, NandanamChennai - 600 035, India.Tel: +91 44 24346425/24347608Fax: +91 44 24346435Email: [email protected]

DelhiEasun Reyrolle Ltd.29/12, Ground Floor, East Patel NagarNew Delhi - 110 008, India.Tel: +91 11 25747321/25747322Fax: +91 11 25747320Email: [email protected]

KolkataEasun Reyrolle Ltd.4, Dr.Sundari Mohan Avenue, 5th FloorFlat No.18, Kolkata - 700 014, India.Tel: +91 33 22848320Fax: +91 33 22848326Email: [email protected]

MumbaiEasun Reyrolle Ltd.23, Kasturi Building, Jamshedji Tata RoadMumbai - 400 020, India.Tel: +91 22 22022270/22855415Fax: +91 22 22825703Email: [email protected]

SecunderabadEasun Reyrolle Ltd.#2, 1st Floor, Paradise ChambersOpp Hotel Ambassador1-7-196 Prender Ghast RoadSecunderabad - 500 003, India.Telefax: +91 40 27817847Email: [email protected]

CORPORATE OFFICEEasun Reyrolle Limited.,98 Sipcot Industrial ComplexHosur 635 126, India.Tel: +91 4344 401600/01/02Fax: +91 4344 276397

TURNKEY PROJECTSBUSINESS/AMR BUSINESS#389, “Rasukumaki”, HulimavuBegur Hobli, Bannerghatta RoadBangalore - 560 076, India.Tel: +91 80 40477200/ 201Fax: +91 80 40477202Email: [email protected]

HOSUR WORKS#98, Sipcot Industrial ComplexHosur - 635 126, India.Tel: +91 4344 401600/01/02Fax: +91 4344 276397

CENTRAL MARKETING &EXPORTS BUSINESS#17/3 ArakereBannerghatta RoadBangalore - 560 076, India.Tel: +91 80 26581023/3268Fax: +91 80 26580642Email: [email protected]

BANGALORE WORKS#17/3 Arakere, Bannerghatta RoadBangalore - 560 076, India.Tel: +91 80 26581023/3268Fax: +91 80 26580642Email: [email protected]

AUTOMATION BUSINESS#389, “Rasukumaki”, HulimavuBegur Hobli, Bannerghatta RoadBangalore - 560 076, India.Tel: +91 80 40477200/ 201Fax: +91 80 40477202Email: [email protected]

Corporate OfficeEasun Reyrolle Limited. 98 Sipcot Industrial Complex,

Hosur 635 126 India.Tel: +91 4344 401600/01/02

Fax: +91 4344 276397www.easunreyrolle.com

Technical Information

Ratings63.5V 110V, 190V A.C

SettingsFixed at 10%, 15%, 20%, 25%, 30% or 40%

or 10% to 25% in 5% steps

or 10% to 40% in 10% steps

Operating time30ms at twice the setting

Burden0.06VA at pick up

6.0VA at 10 times the setting

(standard relay)

Contact arrangements (self reset)

2 normally open

or 1 normally open and 1 normally closed

Contact ratingsMake and carry continuously

1500VA A.C or 1500WD.C within limits of 660V and 3A.

Make and carry 8A for 3 seconds or 16A for 1 second

Break300VA A.C or 75W D.C (inductive L/R = 0.04)

within the limits of 250V and 5A

Wiring Diagrams

Typical Wiring Diagram for B37 Relay

Technical Information

Ratings63.5V 110V, 190V A.C

SettingsFixed at 10%, 15%, 20%, 25%, 30% or 40%

or 10% to 25% in 5% steps

or 10% to 40% in 10% steps

Operating time30ms at twice the setting

Burden0.06VA at pick up

6.0VA at 10 times the setting

(standard relay)

Contact arrangements (self reset)

2 normally open

or 1 normally open and 1 normally closed

Contact ratingsMake and carry continuously

1500VA A.C or 1500WD.C within limits of 660V and 3A.

Make and carry 8A for 3 seconds or 16A for 1 second

Break300VA A.C or 75W D.C (inductive L/R = 0.04)

within the limits of 250V and 5A

Wiring Diagrams

Typical Wiring Diagram for B37 Relay

Neutral Displacement Relay B37

The policy of Easun Reyrolle is one of continuous improvement and development. The company therefore reserves the right to supply equipment,

which may differ slightly from that described and illustrated in this publication.

Description

The relay comprises an attracted armature element fed via a

rectifier and series resistor. It can be provided with either a fixed

setting, or variable settings using a plug bridge. It has a minimum

withstand of rated voltage continuously.

Applications

Neutral displacement detection can be applied in either of the

following situations:

To initiate an alarm for a single phase to earth faulton an insulated neutral system

With such a system an earth fault on one phase will cause the

voltages on the other 2 phases to rise with respect to earth and

can reach the phase-to-phase voltage.

The relay is to be connected across a secondary open delta

winding of a 3 phase, 5 limb, voltage transformer which has the

primary star point earthed. The voltage across the open delta

secondary will rise from zero (or near zero depending on voltage

balance) to as high as 3 times the secondary winding voltage per

phase, e.g. 63.5V windings will produce up to 190V across the

relay for a phase to earth fault close to the VT. B37 relays are

rated to withstand this.

To effect tripping on earthed neutral systems.

When the upstream protection isolates an earth fault on a feeder

on a delta connected HV side of a power transformer, the

possibility remains of voltage rise on the two sound phases if

the feeder continues to be energized from the LV side of the

power transformer. The residual voltage of the feeder operates

the relay at the transformer end of the HV feeder and the relay

trips the LV circuit breaker. When the HV windings of the power

transformer are delta connected, or star connected with the

neutral not available, the neutral displacement protection requires

the same equipment as described for the first application above.

Ordering Information

• Rating

• Setting value or setting range

• Case style and size

Qualification

ISO 9001-2000

Note:

1. All dimensions are in mm

2. All dimensions are measured equidistant from centre line

3. Maximum depth of equipment inside panel : 200mm

PART CASE CUT OUT BEZEL

SIZE A B C D

01 2/3V 149.5 148 170 170

02 1V 221 148 243 170

Cutout Details When the HV windings are star connected with the neutral

available then the relay can be energized from a single phase

voltage transformer having its primary connected between the

neutral and earth.

Either scheme can be supplemented by a definite time delay

relay if required.

Cases

Single pole Modular size 4

Vedette 2/3V or 1V

Neutral Displacement Relay - B37

FACT

/B37

/08-

07/R

EV 1

®Easu

n R

eyro

lle-2

007 -

Easu

n R

eyro

lle,

the

Easu

n R

eyro

lle l

ogo a

nd a

ny

alte

rnativ

e ve

rsio

n t

her

eof

are

reg

iste

red t

rade

mark

s and s

ervi

ce m

ark

s of

Easu

n R

eyro

lle

Sales OfficesBangaloreEasun Reyrolle Ltd.#17/3 Arakere, Bannerghatta Road,Bangalore - 560 076, India.Tel: +91 80 26581023/3268Fax: +91 80 26580642Email: [email protected]

BhopalEasun Reyrolle Ltd.H.No.16, Essarjee HomesNear Gopal Nagar, Kalan RoadPiplani, Bhopal - 462 021, India.Telefax: +91 755 2684221Email: [email protected]

ChennaiEasun Reyrolle Ltd.6th Floor, Temple Tower, 672,Anna Salai, NandanamChennai - 600 035, India.Tel: +91 44 24346425/24347608Fax: +91 44 24346435Email: [email protected]

DelhiEasun Reyrolle Ltd.29/12, Ground Floor, East Patel NagarNew Delhi - 110 008, India.Tel: +91 11 25747321/25747322Fax: +91 11 25747320Email: [email protected]

KolkataEasun Reyrolle Ltd.4, Dr.Sundari Mohan Avenue, 5th FloorFlat No.18, Kolkata - 700 014, India.Tel: +91 33 22848320Fax: +91 33 22848326Email: [email protected]

MumbaiEasun Reyrolle Ltd.23, Kasturi Building, Jamshedji Tata RoadMumbai - 400 020, India.Tel: +91 22 22022270/22855415Fax: +91 22 22825703Email: [email protected]

SecunderabadEasun Reyrolle Ltd.#2, 1st Floor, Paradise ChambersOpp Hotel Ambassador1-7-196 Prender Ghast RoadSecunderabad - 500 003, India.Telefax: +91 40 27817847Email: [email protected]

CORPORATE OFFICEEasun Reyrolle Limited.,98 Sipcot Industrial ComplexHosur 635 126, India.Tel: +91 4344 401600/01/02Fax: +91 4344 276397

TURNKEY PROJECTSBUSINESS/AMR BUSINESS#389, “Rasukumaki”, HulimavuBegur Hobli, Bannerghatta RoadBangalore - 560 076, India.Tel: +91 80 40477200/ 201Fax: +91 80 40477202Email: [email protected]

HOSUR WORKS#98, Sipcot Industrial ComplexHosur - 635 126, India.Tel: +91 4344 401600/01/02Fax: +91 4344 276397

CENTRAL MARKETING &EXPORTS BUSINESS#17/3 ArakereBannerghatta RoadBangalore - 560 076, India.Tel: +91 80 26581023/3268Fax: +91 80 26580642Email: [email protected]

BANGALORE WORKS#17/3 Arakere, Bannerghatta RoadBangalore - 560 076, India.Tel: +91 80 26581023/3268Fax: +91 80 26580642Email: [email protected]

AUTOMATION BUSINESS#389, “Rasukumaki”, HulimavuBegur Hobli, Bannerghatta RoadBangalore - 560 076, India.Tel: +91 80 40477200/ 201Fax: +91 80 40477202Email: [email protected]

Corporate OfficeEasun Reyrolle Limited. 98 Sipcot Industrial Complex,

Hosur 635 126 India.Tel: +91 4344 401600/01/02

Fax: +91 4344 276397www.easunreyrolle.com