netezza site prep specs

-

IBM Netezza 1000-SeriesSite Preparation and Specifications Revised: June 17, 2011

D20281-18 Rev. 11.0

Note: Before using this information and the product that it supports, read the information in “Notices and Trademarks” on page B-1.

© Copyright IBM Corporation 2001-2011.US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.

Contents

Preface

1 IBM Netezza 1000 System Models1000-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1000-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1000-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1000-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1000-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1000-36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1000-48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

1000-72 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

1000-84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

1000-96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

1000-120 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

2 1000-3 SpecificationsElectrical Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Space requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Floor Loading Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Host Server Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4











iii

5 1000-18 SpecificationsSpace requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Electrical Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
























iv

10 1000-84 SpecificationsSpace requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

Electrical Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4

Floor Loading Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5

Host Server Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5











Appendix A: Model Comparison

Appendix B: Notices and TrademarksNotices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3

Open Source Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4

Regulatory and Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6

v

Tables

Table 2-1: 1000-3 Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Table 2-2: 1000-3 Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Table 2-3: 1000-3 Operating Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Table 2-4: 1000-3 Floor Loading Requirements . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Table 2-5: IBM x3650 M3 Host Specifications. . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Table 3-1: 1000-6 Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Table 3-2: 1000-6 Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Table 3-3: 1000-6 Operating Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Table 3-4: 1000-6 Floor Loading Requirements . . . . . . . . . . . . . . . . . . . . . . . . 3-3


Table 4-1: 1000-12 Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Table 4-2: 1000-12 Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Table 4-3: 1000-12 Operating Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Table 4-4: 1000-12 Floor Loading Requirements . . . . . . . . . . . . . . . . . . . . . . . 4-3






Table 5-5: IBM x3850 X5 Host Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 5-4














vii








Table 10-1: 1000-84 Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

Table 10-2: 1000-84 Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 10-4

Table 10-3: 1000-84 Operating Environment. . . . . . . . . . . . . . . . . . . . . . . . . . 10-4

Table 10-4: 1000-84 Floor Loading Requirements . . . . . . . . . . . . . . . . . . . . . . 10-5

Table 10-5: IBM x3850 X5 Host Specifications . . . . . . . . . . . . . . . . . . . . . . . . 10-5

Table 11-1: 1000-96 Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

Table 11-2: 1000-96 Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 11-3

Table 11-3: 1000-96 Operating Environment. . . . . . . . . . . . . . . . . . . . . . . . . . 11-3

Table 11-4: 1000-96 Floor Loading Requirements . . . . . . . . . . . . . . . . . . . . . . 11-4


Table 12-1: 1000-120 Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

Table 12-2: 1000-120 Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . 12-4

Table 12-3: 1000-120 Operating Environment. . . . . . . . . . . . . . . . . . . . . . . . . 12-4

Table 12-4: 1000-120 Floor Loading Requirements . . . . . . . . . . . . . . . . . . . . . 12-5


Table A-1: Model Comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

viii

Figures

Figure 1-1: 1000-3 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Figure 1-2: 1000-6 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Figure 1-3: 1000-12 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3





Figure 1-8: 1000-72 Pod 1 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8


Figure 1-10: 1000-84 Pod1 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9


Figure 1-12: 1000-96 Pod1 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Figure 1-13: 1000-96 Pod 2 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Figure 1-14: 1000-120 Pod1 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Figure 1-15: 1000-120 Pod 2 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Figure 1-16: 1000-120 Pod 3 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Figure 2-1: Rack Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2



Figure 5-1: Space Requirements for a 2-Rack Pod . . . . . . . . . . . . . . . . . . . . . . . 5-2






Figure 9-3: Pod Positioning for Multiple Pods . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

Figure 10-1: Space Requirements for each 4-Rack Pod . . . . . . . . . . . . . . . . . . . 10-2


Figure 10-3: Pod Positioning for Multiple Pods . . . . . . . . . . . . . . . . . . . . . . . . . 10-3




Figure 12-2: Space Requirements for a 2-Rack Pod . . . . . . . . . . . . . . . . . . . . . . 12-3


ix

PrefaceThe IBM Netezza 1000 system is a high-performance, integrated data warehouse appliance that provides unparalleled performance, extensive scaling, high reliability, and ease of use. The system uses a unique architecture that combines current trends in processor, network, and software technologies to deliver a very high-performance system for large enterprise customers.

About This Guide

IBM Netezza 1000 Series Site Preparation and Specifications is written for those who need to understand the site requirements and specifications of each IBM Netezza 1000 model. This guide assumes that you understand the capabilities and capacities of the physical space in which you are installing a IBM Netezza 1000 system.

The guide describes the hardware components that make up the system, and discusses the following:

Preparing a physical location.

Maintaining a location.

Various IBM Netezza 1000 models.

Hardware specifications.

Included in This Guide

This guide is designed to be used before and during installation of the IBM Netezza 1000 system. It contains important information on preparing and maintaining your site. It specif-ically covers the following topics:

Chapter 1, “IBM Netezza 1000 System Models” — Lists the different system models and describes the location of the major components within the system.

Chapter 2, “1000-3 Specifications” — Provides the information necessary to prepare your site for the installation of the IBM Netezza 1000 3 system.







xi


Chapter 10, “1000-84 Specifications” — Provides the information necessary to pre-pare your site for the installation of the IBM Netezza 1000 84 system.



Appendix A, “Model Comparison” — Provides a model comparison of the systems in the current IBM Netezza 1000 product line.

xii

Symbols and Conventions

This guide uses the following typographical conventions:

Numbered steps for procedures

Single-step procedures are preceded by the q symbol

Bulleted lists for topics

Italics for terms, and user-defined variables such as filenames

Abbreviations

This guide uses the following abbreviations throughout:

Abbreviation Description

A ampere

ACID Atomicity, Consistency, Isolation, and Durability

GB Gigabyte

HTTP HyperText Transport Protocol

Hz Hertz

in. Inch

kg Kilogram

KVA Kilo Volt-Amps

KVM Keyboard-Video-Mouse

lb Pound

m meter

Mb Megabit

MB Megabyte

ms Milliseconds

MSFI Mustang Snippet Fabric Interface

MSPU Mustang Snippet Processing Unit

NIC Network Interface Card

NPS Netezza Performance Software

PCI Peripheral Component Interconnect

xiii

If You Need Help

If you are having trouble using the IBM® Netezza® appliance, you should:

1. Retry the action, carefully following the instructions given for that task in the documentation.

2. Go to the Netezza Knowledge Base at https://knowledge.netezza.com. Enter your sup-port username and password. You can search the knowledge base or the latest updates to the product documentation. Click Netezza HelpDesk to submit a support request.

3. If you are unable to access the Netezza Knowledge Base, you can also contact Netezza Support at the following telephone numbers:

North American Toll-Free: +1.877.810.4441

United Kingdom Free-Phone: +0.800.032.8382

International Direct: +1.508.620.2281

Refer to your Netezza maintenance agreement for details about your support plan choices and coverage.

PCIe PCI Express

PCIx PCI eXtended

PDU Power Distribution Unit

RAID Redundant Array of Independent Disks

RPC Remote Power Controller

SAS Serial Attached SCSI

SATA Serial Advanced Technology Attachment

SCSI Small Computer System Interface

SFI Snippet Fabric Interface

SNMP Simple Network Management Protocol

SPA Snippet Processing Array

SPU Snippet Processing Unit

TB Terabyte

VAC Volts Alternating Current

Abbreviation Description

xiv

Comments on the Documentation

We welcome any questions, comments, or suggestions that you have for the IBM Netezza documentation. Please send us an e-mail message at [email protected] and include the following information:

The name and version of the manual that you are using

Any comments that you have about the manual

Your name, address, and phone number

We appreciate your comments on the documentation.

D20281-18 Rev.11.0 i-xv

IBM Netezza 1000-Series Site Preparation and Specifications

i-xvi D20281-18 Rev.11.0

C H A P T E R 1
IBM Netezza 1000 System Models
This chapter contains the following information:

A description of each system, including the number of racks, S-Blades, and SPAs in the system

An illustration of each system showing the placement of components within each rack.

1000-3

The 1000-3 is a single-rack system containing 3 S-Blades housed in 1 SPA.

Figure 1-1 shows a 1000-3 system.

Note: The switch is only visible from the rear of the rack.

Figure 1-1: 1000-3 (front view)

JBOD

S-Blades

JBOD

Host 1 (x3650)

Host 2 (x3650)

KVM

Mgt Switch

1-1


1000-6

The 1000-6 is a single-rack system containing 6 S-Blades housed in 1 SPA.




JBOD

JBOD

S-Blades

JBOD

JBOD

Host 1 (x3650)

Host 2 (x3650)

KVM

Mgt Switch

1-2 D20281-18 Rev.11.0

1000-12

1000-12

The 1000-12 is a single-rack system containing 12 S-Blades housed in 2 SPAs.




JBOD

JBOD

JBOD

JBOD

S-Blades

S-Blades

JBOD

JBOD

JBOD

JBOD

Host 1 (x3650)

Host 2 (x3650)

KVM

Mgt Switch

D20281-18 Rev.11.0 1-3


1000-18

The 1000-18 is a two-rack system containing 18 S-Blades housed in 3 SPAs.

Note: The racks are bolted together into a single unit and cannot be separated.


Note: The switches are only visible from the rear of the rack.


JBOD

JBOD

JBOD

JBOD

JBOD

JBOD

S-Blades S-Blades

S-Blades

JBOD

JBOD

JBOD

JBOD

JBOD

JBOD

Host 1 (x3850 M2) Host 2 (x3850 M2)

KVM

Mgt Switch

Fabric Switch

Fabric Switch

1-4 D20281-18 Rev.11.0

1000-24

1000-24

The 1000-24 is a two-rack system containing 24 S-Blades housed in 4 SPAs.





JBOD JBOD

JBOD JBOD

JBOD JBOD

JBOD JBOD

S-Blades S-Blades

S-Blades S-Blades

JBOD JBOD

JBOD JBOD

JBOD JBOD

JBOD JBOD

Host 1 (x3850 M2) Host 2 (x3850 M2)

KVMMgt Switch

Fabric Switch

Fabric Switch

D20281-18 Rev.11.0 1-5


1000-36

The 1000-36 is a three-rack system containing 36 S-Blades housed in 6 SPAs.





JBOD JBODJBOD

JBOD JBODJBOD

JBOD JBODJBOD

JBOD JBODJBOD

S-Blades S-BladesS-Blades

S-Blades S-BladesS-Blades

JBOD JBODJBOD

JBOD JBODJBOD

JBOD JBODJBOD

JBOD JBODJBOD

Host 1 (x3850 M2) Host 2 (x3850 M2)

KVM

Mgt Switch

Fabric Switch

Fabric Switch

1-6 D20281-18 Rev.11.0

1000-48

1000-48

The 1000-48 is a four-rack system containing 48 S-Blades housed in 8 SPAs.





JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

S-Blades S-BladesS-Blades S-Blades


JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

Host 1 (x3850 M2) Host 2 (x3850 M2)

KVM

Mgt Switch

Fabric Switch

Fabric Switch

D20281-18 Rev.11.0 1-7


1000-72

The 1000-72 is a six-rack system containing 72 S-Blades housed in 12 SPAs.

Note: The racks are bolted together into two distinct units, known as pods. Pods may be located separately from each other, limited by the length (20 meters) of the inter-pod cables. Pods may not be broken apart into individual racks.



Figure 1-8: 1000-72 Pod 1 (front view)


JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD



JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

Host 1 (x3850 M2) Host 2 (x3850 M2)

KVM

Mgt Switch

Fabric Switch

Fabric Switch

JBOD JBOD

JBOD JBOD

JBOD JBOD

JBOD JBOD

S-Blades S-Blades

S-Blades S-Blades

JBOD JBOD

JBOD JBOD

JBOD JBOD

JBOD JBOD

Mgt Switch Fabric Switch

Fabric SwitchKVM

1-8 D20281-18 Rev.11.0

1000-84

1000-84

The 1000-84 is a seven-rack system containing 84 S-Blades housed in 14 SPAs.




Figure 1-10: 1000-84 Pod1 (front view)


JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD



JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

Host 1 (x3850 M2) Host 2 (x3850 M2)

KVM

Mgt Switch

Fabric Switch

Fabric Switch

JBOD JBOD JBOD

JBOD JBOD JBOD

JBOD JBOD JBOD

JBOD JBOD JBOD

S-Blades S-Blades S-Blades

S-Blades S-Blades S-Blades

JBOD JBOD JBOD

JBOD JBOD JBOD

JBOD JBOD JBOD

JBOD JBOD JBOD

Mgt Switch Fabric Switch Fabric Switch

Fabric Switch Fabric SwitchKVM

D20281-18 Rev.11.0 1-9


1000-96

The 1000-96 is a eight-rack system containing 96 S-Blades housed in 16 SPAs.






JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD



JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

Host 1 (x3850 M2) Host 2 (x3850 M2)

KVM

Mgt Switch

Fabric Switch

Fabric Switch

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD



JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD



1-10 D20281-18 Rev.11.0

1000-120

1000-120

The 1000-120 is a ten-rack system containing 120 S-Blades housed in 20 SPAs.

Note: The racks are bolted together into three distinct units, known as pods. Pods may be located separately from each other, limited by the length (20 meters) of the inter-pod cables. Pods may not be broken apart into individual racks.





JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD



JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

Host 1 (x3850 M2) Host 2 (x3850 M2)

KVM

Mgt Switch

Fabric Switch

Fabric Switch

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD



JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD

JBOD JBODJBOD JBOD



D20281-18 Rev.11.0 1-11



JBOD JBOD

JBOD JBOD

JBOD JBOD

JBOD JBOD

S-Blades S-Blades

S-Blades S-Blades

JBOD JBOD

JBOD JBOD

JBOD JBOD

JBOD JBOD

Mgt Switch Fabric Switch

Fabric SwitchKVM

1-12 D20281-18 Rev.11.0

C H A P T E R 2
1000-3 Specifications
This chapter explains the following requirements for the 1000-3 system:

Space requirements

Electrical power requirements

Environmental requirements

Floor loading requirements

Electrical Power Requirements

Each 1000-3 system requires two separately protected power circuits. The power require-ments for each circuit are listed in Table 2-1.

Note: IBM Netezza recommends that the power supplied to the rack be uninterruptible.

Table 2-1: 1000-3 Electrical Requirements

Specification Value

Circuits 2

Total Plugs (Drops) 2

Voltage 200-240 VAC, 50Hz/60 Hz (Single Phase)

Circuit Breaker Rating 20 Amps (Single Phase)

Connector NEMA 30A L6-30 (NA models)IEC 309 32A 2P+G (EU models)

Maximum Power 2,930 W

Power/Area 385 W/ft2

(4,141 W/m2)

2-1


Space requirements

Each rack in the system has a footprint of 25.5 in. (64.8 cm) by 43 in. (109.2 cm). An additional 60 in. (152.4 cm) of clear space is required in front of each rack and 30 in. (76.2 cm) behind the rack. This is to allow unrestricted airflow and access to the system.

Note: The 1000-series systems are housed in a rack that is 1.5 in. (3.8 cm) wider than previous Netezza systems. This means that the 1000-series system is wider than a stan-dard 24 in. (61 cm) data center floor tile. Plan accordingly.

A full height system rack is 87.5 in. (222 cm) tall including its shipping pallet. Without the pallet, the rack stands 79.5 in. (202 cm) tall including casters. Allow for this when plan-ning the movement of the system from the unloading point to its permanent location.

Figure 2-1 shows the space requirements for each rack.

Figure 2-1: Rack Space Requirements

The total space requirements for the 1000-3 system are listed in Table 2-2.

Table 2-2: 1000-3 Space Requirements

Physical Including Clearance

Footprint (WxD) 25.5 in. by 43 in.(64.8 cm x 109.2 cm)

25.5 in. by 130 in.(64.8 cm x 330.2 cm)

25.5 in(64.8 cm)

30 in(76 cm)

40 in(101.6 cm)

60 in(152 cm)

between rows

36 in91.5 cm)

2-2 D20281-18 Rev.11.0

Environmental Requirements


The 1000-3 system is designed to operate within the following temperature, humidity, and altitude ranges:

Floor Loading Requirements

The floor that supports the 1000-3 system must be capable of supporting a minimum of 132 lbs/ft2 (642 kg/m2).

Table 2-3: 1000-3 Operating Environment

Operating Non-operating

Temperature 10°C to 35°C (50°F to 95°F)

-15°C to 45°C (5°F to 113°F)

Altitude 0 to 3,048 m (0 to 10,000 ft)

0 to 9,144 m (0 to 30,000 ft)

Humidity 20% to 80% non-condensing 10% to 90% non-condensing

Cooling 9,998 BTU/hr

Table 2-4: 1000-3 Floor Loading Requirements

Specification Value

Maximum Weight 1,000 lb(453.6 kg)

Maximum Weight/Area 131.3 lb/ft2

(641.1 kg/m2)

D20281-18 Rev.11.0 2-3


Host Server Specifications

Table 2-5: IBM x3650 M3 Host Specifications

Feature Number Description

Processors two Quad-core Intel Xeon 2.4 GHz, 12MB L3 1066MHz 80w

Memory — 24 GB, PC3-10600 (DDR3) SDRAM

Power supplies two 675W, Redundant, hot-pluggable

Fans three N+1 Redundant, hot-pluggable

NIC four ports (two available)

Four Gigabit ethernet ports (embedded)

NIC one quad port card(two available)

One Quad Port PCIe Gigabit Adapter

NIC one dual port card(one available)

One Dual Port PCIe 10 Gigabit Adapter

IMM port one Integrated Management Module dedicated NIC (10/100 Mb)

300 GB SAS drives seven Hot-swappable, in a RAID 10 configuration

PCI slots four(two available)

Four PCI-Express x8 (one full length, one half length, two low profile)

USB 2.0 ports five Two front, two rear, one internal

Serial port one

DVD-ROM/CD-RW one 8X / 24X max

Form Factor 2U (3.5”) rack-mountable

Management IMM

2-4 D20281-18 Rev.11.0

C H A P T E R 3

Space requirements








Specification Value

Circuits 2


Voltage 200-240 VAC, 50Hz/60 Hz (Single Phase)

Circuit Breaker Rating 30 Amps (Single Phase)

Connector NEMA 30A L6-30 (NA models)IEC 309 32A 2P+G (EU models)



(5,822 W/m2)

3-1


Space requirements


Note: The 1000-series system is housed in a rack that is 1.5 in. (3.8 cm) wider than previ-ous Netezza systems. This means that the 1000-series system is wider than a standard 24 in. (61 cm) data center floor tile. Plan accordingly.








25.5 in. by 130 in.(64.8 cm x 330.2 cm)

25.5 in(64.8 cm)

30 in(76 cm)

40 in(101.6 cm)

60 in(152 cm)

between rows

36 in91.5 cm)

3-2 D20281-18 Rev.11.0





The floor that supports the 1000-6 system must be capable of supporting a minimum of 171 lbs/ft2 (834 kg/m2).




-15°C to 45°C (5°F to 113°F)


0 to 9,144 m (0 to 30,000 ft)


Cooling 14,058 BTU/hr


Specification Value



(833.4 kg/m2)

D20281-18 Rev.11.0 3-3




















Serial port one



Management IMM

3-4 D20281-18 Rev.11.0

C H A P T E R 4

Space requirements








Specification Value

Circuits 2


Voltage 200-240/380-415 VAC, 50 Hz (EU models — 3-Phase Wye)200-208 VAC, 60 Hz (NA models — 3-Phase Delta)

200-240 VAC, 50Hz/60 Hz (Single Phase)

Circuit Breaker Rating 30 Amps (EU models — 3-Phase Wye)40 Amps (NA models — 3-Phase Delta)

60 Amps (Single Phase)

Connector IEC 309 32A 3P+N+G (EU models — 3-Phase Wye)IEC 309 60A 3P+G (NA models — 3-Phase Delta)

IEC 309 60A 2P+G (Single Phase)



(10,203 W/m2)

4-1


Space requirements


Note: The 1000-series system is housed in a rack that is 1.5 in. (3.8 cm) wider than previ-ous Netezza systems. This means that the 1000-series system is wider than a standard 24 in. (61 cm) data center floor tile. Plan accordingly.








25.5 in. by 130 in.(64.8 cm x 330.2 cm)

25.5 in(64.8 cm)

30 in(76 cm)

40 in(101.6 cm)

60 in(152 cm)

between rows

36 in91.5 cm)

4-2 D20281-18 Rev.11.0





The floor that supports the 1000-12 system must be capable of supporting a minimum of 263 lbs/ft2 (1,283 kg/m2).




-15°C to 45°C (5°F to 113°F)


0 to 9,144 m (0 to 30,000 ft)


Cooling 24,636 BTU/hr —


Specification Value



(1,282.6 kg/m2)

D20281-18 Rev.11.0 4-3




















Serial port one



Management IMM

4-4 D20281-18 Rev.11.0

C H A P T E R 5

Space requirements




Space requirements

The 1000-18 consists of two racks. The racks are bolted together into a group of racks called a pod. In this system there is a single pod of two racks.

RackEach rack in the system has a footprint of 25.5 in. (64.8 cm) by 43 in. (109.2 cm). An additional 60 in. (152.4 cm) of clear space is required in front of each rack and 30 in. (76.2 cm) behind the rack. This is to allow unrestricted airflow and access to the system.

Note: The racks that are used for 1000-series systems are 1.5 in. (3.8 cm) wider than those used in previous Netezza systems. This means that each rack in the 1000-series sys-tem is wider than a standard 24 in. (61 cm) data center floor tile. Plan accordingly.


PodsThe 1000-18 consists of a pod with two racks. The space requirements for the pod are listed in Table 5-1.

Figure 5-1 shows the space requirements for the pod.


Number of RacksFootprint


2 51 in. by 43 in.(128.6 cm x 109.2 cm)

51 in. by 130 in.(128.6 cm x 330.2 cm)

5-1


Figure 5-1: Space Requirements for a 2-Rack Pod




30 in(76 cm)

40 in(101.6 cm)

36 in(91.5 cm)

51 in(129.6 cm)

Front

Rear


Specification 2-Rack Pod

Circuits 2









5-2 D20281-18 Rev.11.0







(7,815 W/m2)






-15°C to 45°C (5°F to 113°F)


0 to 9,144 m (0 to 30,000 ft)







(958.3 kg/m2)

D20281-18 Rev.11.0 5-3



Table 5-5: IBM x3850 X5 Host Specifications


Processors four Six-core Intel Xeon 2.0 GHz, 18MB L3 1066MHz 105w

Memory — 128 GB, PC3-8500 (DDR3-1066) RDIMMs


Fans six N+1 Redundant, hot-pluggable

NIC two ports(two available)

Two Gigabit ethernet ports (embedded)


One Quad Port 1 Gigabit Adapter

NIC three dual port card(internal use)

Three Dual Port 10 Gigabit Adapter

IMM port one Remote Supervisor Adapter dedicated NIC (10/100 Mb)


PCI slots seven(three available)

Seven PCIe (3 available)

USB 2.0 ports four Two front, two rear

Serial port one


Form factor 4U (7”) Rack-mountable

Management IMM

5-4 D20281-18 Rev.11.0

C H A P T E R 6

Space requirements




Space requirements

The 1000-24 consists of two racks. The racks are bolted together into a group of racks called a pod. In this system there is a single pod of two racks.




PodsThe 1000-24 consists of a pod with two racks. The space requirements for the pod are listed in Table 6-1.

Figure 6-1 shows the space requirements for the pod.




2 51 in. by 43 in.(128.6 cm x 109.2 cm)

51 in. by 130 in.(128.6 cm x 330.2 cm)

6-1






30 in(76 cm)

40 in(101.6 cm)

36 in(91.5 cm)

51 in(129.6 cm)

Front

Rear



Circuits 2









6-2 D20281-18 Rev.11.0







(10,005 W/m2)






-15°C to 45°C (5°F to 113°F)


0 to 9,144 m (0 to 30,000 ft)







(1,282.6 kg/m2)

D20281-18 Rev.11.0 6-3




















Serial port one



Management IMM

6-4 D20281-18 Rev.11.0

C H A P T E R 7

Space requirements




Space requirements

The 1000-36 consists of three racks. The racks are bolted together into a group of racks called a pod. In this system there is a single pod of three racks.




PodsThe 1000-36 consists of one 3-rack pod. The space requirements for the pod are listed in Table 7-1.




3 76.5 in. by 43 in.(194.3 cm x 109.2 cm)

76.5 in. by 130 in.(194.3 cm x 330.2 cm)

7-1


Figure 7-1 shows the space requirements for the Pod.





30 in(76 cm)

40 in(101.6 cm)

36 in(91.5 cm)

76.5 in(194.3 cm)

Front

Rear



Circuits 2




Circuit/Breaker Rating 30 Amps (EU models — 3-Phase Wye)40 Amps (NA models — 3-Phase Delta)





7-2 D20281-18 Rev.11.0







(9,591 W/m2)






-15°C to 45°C (5°F to 113°F)


0 to 9,144 m (0 to 30,000 ft)







(1,282.6 kg/m2)

D20281-18 Rev.11.0 7-3




















Serial port one



Management IMM

7-4 D20281-18 Rev.11.0

C H A P T E R 8

Space requirements




Space requirements

The 1000-48 consists of four racks. The racks are bolted together into a group of racks called a pod. In this system there is a single pod of four racks.




PodsThe 1000-48 consists of one 4-rack pod. The space requirements for the pod are listed in Table 8-1.




4 102 in. by 43 in.(259.2 cm x 109.2 cm)

102 in. by 130 in.(259.2 cm x 330.2 cm)

8-1


Figure 8-1 shows the space requirements for the Pod.





30 in(76 cm)

40 in(101.6 cm)

36 in(91.5 cm)

102 in(259.1 cm)

Front

Rear



Circuits 2









8-2 D20281-18 Rev.11.0







(9,384 W/m2)






-15°C to 45°C (5°F to 113°F)


0 to 9,144 m (0 to 30,000 ft)







(1,282.6 kg/m2)

D20281-18 Rev.11.0 8-3




















Serial port one



Management IMM

8-4 D20281-18 Rev.11.0

C H A P T E R 9

Space requirements




Space requirements

The 1000-72 consists of a total of six racks. The racks are bolted together into separate groups called pods. In this system there are a total of two pods; one pod of four racks, and one pod of two racks.




PodsThe 1000-72 consists of two separate pods. The space requirements for each pod are listed in Table 9-1.




Pod 1 4 102 in. by 43 in.(259.2 cm x 109.2 cm)

102 in. by 130 in.(259.2 cm x 330.2 cm)

9-1


Figure 9-1 shows the space requirements for Pod 1.


Pod 2 2 51 in. by 43 in.(128.6 cm x 109.2 cm)

51 in. by 130 in.(128.6 cm x 330.2 cm)




30 in(76 cm)

40 in(101.6 cm)

36 in(91.5 cm)

102 in(259.1 cm)

Front

Rear

9-2 D20281-18 Rev.11.0

Space requirements



When positioning the pods, they may be placed side-by-side, front-to-front, or rear-to-rear. Spacing between pods placed front-to-front or rear-to-rear must be as shown in Figure 9-3.

Figure 9-3: Pod Positioning for Multiple Pods

30 in(76 cm)

40 in(101.6 cm)

36 in(91.5 cm)

51 in(129.6 cm)

Front

Rear

102 in(152 cm)

D20281-18 Rev.11.0 9-3








Specification Pod 1 Pod 2 Total System

Circuits 2

Total Plugs (Drops) 8 4 12







Maximum Power 26,560 W 12,960 W 39,520 W


(9,308 W/m2)




-15°C to 45°C (5°F to 113°F)


0 to 9,144 m (0 to 30,000 ft)



9-4 D20281-18 Rev.11.0






Specification Pod 1 Pod 2


4,000 lb(1814.4 kg)


(1,282.6 kg/m2)


















Serial port one


D20281-18 Rev.11.0 9-5



Management IMM



9-6 D20281-18 Rev.11.0

C H A P T E R 10

Space requirements




Space requirements

The 1000-84 consists of a total of seven racks. The racks are bolted together into separate groups called pods. In this system there are a total of two pods; one pod of four racks and one pod of three racks.








Pod 1 4 102 in. by 43 in.(259.2 cm x 109.2 cm)

102 in. by 130 in.(259.2 cm x 330.2 cm)

Pod 2 3 76.5 in. by 43 in.(194.3 cm x 109.2 cm)

76.5 in. by 130 in.(194.3 cm x 330.2 cm)

10-1


Figure 10-1 and Figure 10-2 show the space requirements for each pod.

Figure 10-1: Space Requirements for each 4-Rack Pod


30 in(76 cm)

40 in(101.6 cm)

36 in(91.5 cm)

102 in(259.1 cm)

Front

Rear

30 in(76 cm)

40 in(101.6 cm)

36 in(91.5 cm)

76.5 in(194.3 cm)

Front

Rear

10-2 D20281-18 Rev.11.0

Space requirements



102 in(152 cm)

D20281-18 Rev.11.0 10-3









Circuits 2










(9,310 W/m2)




-15°C to 45°C (5°F to 113°F)


0 to 9,144 m (0 to 30,000 ft)



10-4 D20281-18 Rev.11.0








6,000 lb(2721.6 kg)


(1,282.6 kg/m2)


















Serial port one


D20281-18 Rev.11.0 10-5



Management IMM



10-6 D20281-18 Rev.11.0

C H A P T E R 11

Space requirements




Space requirements

The 1000-96 consists of a total of eight racks. The racks are bolted together into separate groups called pods. In this system there are a total of two pods of four racks.








Pod 1 and Pod 2

4 102 in. by 43 in.(259.2 cm x 109.2 cm)

102 in. by 130 in.(259.2 cm x 330.2 cm)

11-1


Figure 11-1 shows the space requirements for each pod.




30 in(76 cm)

40 in(101.6 cm)

36 in(91.5 cm)

102 in(259.1 cm)

Front

Rear

102 in(152 cm)

11-2 D20281-18 Rev.11.0









Circuits 2










(9,242 W/m2)




-15°C to 45°C (5°F to 113°F)


0 to 9,144 m (0 to 30,000 ft)



D20281-18 Rev.11.0 11-3








8,000 lb(3628.8 kg)


(1,282.6 kg/m2)


















Serial port one


11-4 D20281-18 Rev.11.0



Management IMM



D20281-18 Rev.11.0 11-5


11-6 D20281-18 Rev.11.0

C H A P T E R 12

Space requirements




Space requirements

The 1000-120 consists of a total of ten racks. The racks are bolted together into separate groups called pods. In this system there are a total of three pods; two pods of four racks, and a single pod of two racks.




PodsThe 1000-120 consists of three separate pods. The space requirements for each pod are listed in Table 12-1.




Pod 1 and Pod 2

4 102 in. by 43 in.(259.2 cm x 109.2 cm)

102 in. by 130 in.(259.2 cm x 330.2 cm)

12-1


Figure 12-1 shows the space requirements for Pods 1 and 2.


Pod 3 2 51 in. by 43 in.(128.6 cm x 109.2 cm)

51 in. by 130 in.(128.6 cm x 330.2 cm)




30 in(76 cm)

40 in(101.6 cm)

36 in(91.5 cm)

102 in(259.1 cm)

Front

Rear

12-2 D20281-18 Rev.11.0

Space requirements





30 in(76 cm)

40 in(101.6 cm)

36 in(91.5 cm)

51 in(129.6 cm)

Front

Rear

102 in(152 cm)

D20281-18 Rev.11.0 12-3



Each 1000-120 system requires two separately protected power circuits. The power requirements for each circuit are listed in Table 12-2.





Specification Pod 1 Pod 2 Pod 3 Total System

Circuits 2

Total Plugs (Drops) 8 8 4 20







Maximum Power 26,560 W 25,760 W 12,960 W 65,280 W


(9,225 W/m2)




-15°C to 45°C (5°F to 113°F)


0 to 9,144 m (0 to 30,000 ft)



12-4 D20281-18 Rev.11.0






Specification Pod 1 Pod 2 Pod 3


8,000 lb(3628.8 kg)

4,000 lb(1814.4 kg)


(1,282.6 kg/m2)


















Serial port one



Management IMM

D20281-18 Rev.11.0 12-5


12-6 D20281-18 Rev.11.0

A P P E N D I X A
Model Comparison
Table A-1 provides a 1000-series model comparison.

Table A-1: Model Comparison

NPS System User DataHost

ProcessorsS-Blades Racks

High Availability

1000-3 8 TB 2 3 1 Yes

1000-6 16 TB 2 6 1 Yes

1000-12 32 TB 2 12 1 Yes

1000-18 48 TB 4 18 2 Yes

1000-24 64 TB 4 24 2 Yes

1000-36 96 TB 4 36 3 Yes

1000-48 128 TB 4 48 4 Yes

1000-72 192 TB 4 72 6 Yes

1000-84 224 TB 4 84 7 Yes

1000-96 256 TB 4 96 8 Yes

1000-120 320 TB 4 120 10 Yes

A-1


A-2 D20281-18 Rev.11.0

A P P E N D I X B
Notices and Trademarks
What’s in this appendixNotices

Trademarks

Open Source Notifications

Regulatory and Compliance

This information was developed for products and services offered in the U.S.A.

Notices

IBM may not offer the products, services, or features discussed in this document in other countries. Consult your local IBM representative for information on the products and ser-vices currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any IBM intellectual property right may be used instead. However, it is the user's responsibility to evaluate and verify the operation of any non-IBM product, program, or service.

IBM may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not grant you any license to these patents. You can send license inquiries, in writing, to:

IBM Director of LicensingIBM CorporationNorth Castle DriveArmonk, NY 10504-1785 U.S.A.

For license inquiries regarding double-byte character set (DBCS) information, contact the IBM Intellectual Property Department in your country or send inquiries, in writing, to:

Intellectual Property LicensingLegal and Intellectual Property LawIBM Japan Ltd.1623-14, Shimotsuruma, Yamato-shiKanagawa 242-8502 Japan

The following paragraph does not apply to the United Kingdom or any other country where such provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE

B-1


IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied war-ranties in certain transactions, therefore, this statement may not apply to you.

This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new edi-tions of the publication. IBM may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice.

Any references in this information to non-IBM Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this IBM product and use of those Web sites is at your own risk.

IBM may use or distribute any of the information you supply in any way it believes appropri-ate without incurring any obligation to you.

Licensees of this program who wish to have information about it for the purpose of enabling: (i) the exchange of information between independently created programs and other programs (including this one) and (ii) the mutual use of the information which has been exchanged, should contact:

IBM Corporation26 Forest StreetMarlborough, MA 01752 U.S.A.

Such information may be available, subject to appropriate terms and conditions, including in some cases, payment of a fee.

The licensed program described in this document and all licensed material available for it are provided by IBM under terms of the IBM Customer Agreement, IBM International Pro-gram License Agreement or any equivalent agreement between us.

Any performance data contained herein was determined in a controlled environment. Therefore, the results obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Fur-thermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.

Information concerning non-IBM products was obtained from the suppliers of those prod-ucts, their published announcements or other publicly available sources. IBM has not tested those products and cannot confirm the accuracy of performance, compatibility or any other claims related to non-IBM products. Questions on the capabilities of non-IBM products should be addressed to the suppliers of those products.

All statements regarding IBM's future direction or intent are subject to change or with-drawal without notice, and represent goals and objectives only.

This information is for planning purposes only. The information herein is subject to change before the products described become available.

This information contains examples of data and reports used in daily business operations. To illustrate them as completely as possible, the examples include the names of individu-als, companies, brands, and products. All of these names are fictitious and any similarity to the names and addresses used by an actual business enterprise is entirely coincidental.

B-2 D20281-18 Rev.11.0

Trademarks

COPYRIGHT LICENSE:

This information contains sample application programs in source language, which illustrate programming techniques on various operating platforms. You may copy, modify, and dis-tribute these sample programs in any form without payment to IBM, for the purposes of developing, using, marketing or distributing application programs conforming to the appli-cation programming interface for the operating platform for which the sample programs are written. These examples have not been thoroughly tested under all conditions. IBM, there-fore, cannot guarantee or imply reliability, serviceability, or function of these programs. The sample programs are provided "AS IS", without warranty of any kind. IBM shall not be liable for any damages arising out of your use of the sample programs.

Each copy or any portion of these sample programs or any derivative work, must include a copyright notice as follows:

© (your company name) (year). Portions of this code are derived from IBM Corp. Sample Programs. © Copyright IBM Corp. _enter the year or years_. All rights reserved.

If you are viewing this information softcopy, the photographs and color illustrations may not appear.

Trademarks

IBM, the IBM logo, and ibm.com are trademarks of International Business Machines Corp., registered in many jurisdictions worldwide. Other product and service names might be trademarks of IBM or other companies. A current list of IBM trademarks is available on the Web at www.ibm.com/legal/copytrade.shtml.

Netezza, the Netezza logo, the circle-N logo, TwinFin, Skimmer, Snippet Blades, S-Blades, NPS, Snippet, Snippet Processing Unit, SPU, Snippet Processing Array, SPA, Performance Server, Netezza Performance Server, Asymmetric Massively Parallel Processing, AMPP, Intelligent Query Streaming and other marks are trademarks or registered trademarks of Netezza Corporation, an IBM Company, in the United States and/or other countries. All rights reserved.

The following terms are trademarks or registered trademarks of other companies:

Adobe is a registered trademark of Adobe Systems Incorporated in the United States, and/or other countries.

Linux is a registered trademark of Linus Torvalds in the United States, other countries, or both.

Microsoft, Windows, Windows NT, and the Windows logo are trademarks of Microsoft Corp-pration in the United States, other countries, or both.

NEC is a registered trademark of NEC Corporation.

UNIX is a registered trademark of The Open Group in the United States and other countries.

Java and all Java-based trademarks are trademarks of Sun Microsystems, Inc. in the United States, other countries, or both.

Red Hat is a trademark or registered trademark of Red Hat, Inc. in the United States and/or other countries.

D-CC, D-C++, Diab+, FastJ, pSOS+, SingleStep, Tornado, VxWorks, Wind River, and the Wind River logo are trademarks, registered trademarks, or service marks of Wind River Sys-tems, Inc. Tornado patent pending.

D20281-18 Rev.11.0 B-3


APC and the APC logo are trademarks or registered trademarks of American Power Conver-sion Corporation.

All document files and software of the above named third-party suppliers are provided "as is" and may contain deficiencies. Netezza and its suppliers disclaim all warranties of any kind, express or implied, including, without limitation, those of merchantability, fitness for a particular purpose, and non infringement.

In no event will Netezza or its suppliers be liable for indirect, incidental, consequential, special, or economic damages (including lost business profits, business interruption, loss or damage of data, and the like), or the use or inability to use the above-named third-party products, even if Netezza or its suppliers have been advised of the possibility of such damages.

Other company, product or service names may be trademarks or service marks of others.


PostgreSQL

Portions of this publication were derived from PostgreSQL documentation. For those por-tions of the documentation that were derived originally from PostgreSQL documentation, and only for those portions, the following applies:

PostgreSQL is copyright © 1996-2001 by the PostgreSQL global development group and is distributed under the terms of the license of the University of California below.

Postgres95 is copyright © 1994-5 by the Regents of the University of California.

Permission to use, copy, modify, and distribute this documentation for any purpose, with-out fee, and without a written agreement is hereby granted, provided that the above copyright notice and this paragraph and the following two paragraphs appear in all copies.

In no event shall the University of California be liable to any party for direct, indirect, spe-cial, incidental, or consequential damages, including lost profits, arising out of the use of this documentation, even if the University of California has been advised of the possibility of such damage.

The University of California specifically disclaims any warranties, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. The doc-umentation provided hereunder is on an "as-is" basis, and the University of California has no obligations to provide maintenance, support, updates, enhancements, or modifications.

ICU Library

The Netezza implementation of the ICU library is an adaptation of an open source library Copyright (c) 1995-2003 International Business Machines Corporation and others.

ICU License - ICU 1.8.1 and laterCOPYRIGHT AND PERMISSION NOTICE

Copyright (c) 1995-2003 International Business Machines Corporation and othersAll rights reserved.

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restric-tion, including without limitation the rights to use, copy, modify, merge, publish, distribute, and/or sell copies of the Software, and to permit persons to whom the Software

B-4 D20281-18 Rev.11.0


is furnished to do so, provided that the above copyright notice(s) and this permission notice appear in all copies of the Software and that both the above copyright notice(s) and this permission notice appear in supporting documentation.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR HOLDERS INCLUDED IN THIS NOTICE BE LIABLE FOR ANY CLAIM, OR ANY SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLI-GENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization of the copyright holder.

ODBC Driver

The Netezza implementation of the ODBC driver is an adaptation of an open source driver, Copyright © 2000, 2001, Great Bridge LLC. The source code for this driver and the object code of any Netezza software that links with it are available upon request to [email protected]

Botan License

Copyright (C) 1999-2008 Jack Lloyd

2001 Peter J Jones2004-2007 Justin Karneges2005 Matthew Gregan2005-2006 Matt Johnston2006 Luca Piccarreta2007 Yves Jerschow2007-2008 FlexSecure GmbH2007-2008 Technische Universitat Darmstadt2007-2008 Falko Strenzke2007-2008 Martin Doering2007 Manuel Hartl2007 Christoph Ludwig2007 Patrick Sona

All rights reserved.

Redistribution and use in source and binary forms, for any use, with or without modifica-tion, of Botan (http://botan.randombit.net/license.html) is permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of condi-tions, and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions, and the following disclaimer in the documentation and/or other materials pro-vided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR(S) "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRAN-TIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE DISCLAIMED.

D20281-18 Rev.11.0 B-5


IN NO EVENT SHALL THE AUTHOR(S) OR CONTRIBUTOR(S) BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAM-AGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOW-EVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITYOF SUCH DAMAGE.


Regulatory Notices

Install the NPS system in a restricted-access location. Ensure that only those trained to operate or service the equipment have physical access to it. Install each AC power outlet near the NPS rack that plugs into it, and keep it freely accessible.

Provide approved 30A circuit breakers on all power sources.

Product may be powered by redundant power sources. Disconnect ALL power sources before servicing.

High leakage current. Earth connection essential before connecting supply. Courant de fuite élevé. Raccordement à la terre indispensable avant le raccordement au réseau.

Homologation Statement

Attention: This product is not intended to be connected directly or indirectly by any means whatsoever to interfaces of public telecommunications networks, neither to be used in a Public Services Network.

FCC - Industry Canada Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reason-able protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

WEEE

Netezza Corporation is committed to meeting the requirements of the European Union (EU) Waste Electrical and Electronic Equipment (WEEE) Directive. This Directive requires pro-ducers of electrical and electronic equipment to finance the takeback, for reuse or recycling, of their products placed on the EU market after August 13, 2005.

CE Statement (Europe)

This product complies with the European Low Voltage Directive 73/23/EEC and EMC Direc-tive 89/336/EEC as amended by European Directive 93/68/EEC.

B-6 D20281-18 Rev.11.0


Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

VCCI Statement

この装置は、情報処埋装置等電波障害自主規制協議会　（VCCI）の基準に基づくクラス A 情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起越すことがあります。この場合には使用者が適切な対策を講ずるう要求されることがあります。

D20281-18 Rev.11.0 B-7


B-8 D20281-18 Rev.11.0

netezza site prep specs

Documents

dual port

nema 30a l6

quad port

series site

kvm mgt switch

gigabit ethernet

floor loading

previous netezza