Job: Item No.:Model S914

T Y P I C A L I N S T A L L A T I O N S

A Scrapping, Pre-Flushing andFood Waste Collecting System

n Standard Scrap Basin, Model S914n Pot/Pan Scrap Basin, Model P914Widely accepted in areas that restrict

the use of food waste disposers.An Economical Pulper Alternative, the Collector washes soluble food waste harmlessly through the sewer, reducing bulk food waste by as much as 50% and weight by as much as 80%.Recirculated Water used for pre-flushing typically reduces water and sewer costs dramatically. The Collector consumes only 2 gallons of new water per minute while the pre-flushing water plume recirculates at a 30-gallon rate.Scrapping Speed is more than doubled compared to an overhead pre-rinse since the worker’s hands are free for scrapping. The Collector lets you keep up with small to medium size conveyor dishmachines.Problem Dishes, Trays and Cookware with dried or baked-on food need much less hand work. They can be soaked in the Collector basin while scrapping continues on other dishes. HydroLogic Control Panel saves water and energy.Includes patented operator sensing technology with two water saving modes.Job: Item No.:

Model P914

Model S914

Model P914

Scrap CollectorTM

U.S. Pat. No. 7,815,134

Scrap Collector™ Model S914 Pot/Pan Scrap Collector™ Model P914

NOTE: Dimensions in parenthesis are in centimeters

22 1/4"(56.52)

24 13/16"(63.09)

TABLE CUTOUT DETAIL

TOP VIEW

21 1/2"(54.61)

26 13/16"(68.10)

24 1/2"(62.23)

211/2"(54.61)

Model S914

22 1/4"(56.52)

36 1/2"(92.78)

TABLE CUTOUT DETAIL

TOP VIEW

33 3/16"(84.30)

38 1/2"(97.79)

24 1/2"(62.23)

211/2"(54.61)

Model P914

Model S914 shown - P914 similar

14 7/8"(37.78)

32 7/8" (83.50)adjustable to35 7/8" (91.12)

7 7/16" (18.82) to10 7/16" (26.44)

4 9/16"(11.62)

18 1/8"(46.10)

15 3/8"(39.05)

4 9/16"(11.62)

24"(61.01)

15 7/8"(40.33)

1 7/16"(3.70)

FRONT VIEWLEFT SIDE VIEW

22" (55.88)miniumumclearanceoverheadfor basketremoval

Air Gap

ONE BASKET PROVIDED WITH UNITAdditional basket recommended at additional cost

4 3/16"(10.60)

Plume heightadjustment valve

RemovableTop

Hot and coldshutoff valves1/2” NPT

1/2” conduitknockoutelectrical connection

Tank drain2” NPT

UTILITY CONNECTION

UTILITY CONNECTION

UTILITY CONNECTION

Scrap Basket dimensions18 9/16" dia. x 131/4" high(47.2) dia. x (33.7) high

UTILITYCONNECTION

• Incoming electrical connection ➔ factory wired control panel

• Incoming hot/cold water connection ➔ factory plumbed water harness

• Drain connection ➔ 2” NPT

24” min.Dish rack space

Gusher Plate

DishMachine

Dish Flow

Scrap Collector™ Model S914 Pot/Pan Scrap Collector™ Model P914

Model S914 shown - P914 similar

2” TANK DRAIN(Piping not furnished)

ALL CONNECTIONS ARE TO BE MADE BY

QUALIFIED PERSONNEL WHO WILL OBSERVE

ALL LOCAL AND NATIONAL CODES.

The gusher plate should be situated on the same side as the dish machine.

Leave a minimum of 24” between the Collector and dish machine for a dish rack.

The control and operator sensor can be mounted on either side of the Collector using existing fasteners, mounting holes and wiring to accommodate dish flow to the left or dish flow to the right. It is not necessary to disconnect factory-installed wiring.

The control and sensor should always face the operator.

If necessary, the control can be mounted remotely. Additional field wiring and hardware will be necessary.Contact service for installation advice.

Upon request, the Collector top may be shipped separately to a fabricator for welding to table.

CONSTRUCTIONn Tank - 2 Piece Stainless Steeln Adjustable Legs - Stainless Steel n Control Panel - Stainless Steeln Salvage Basin - High Impact Polymern Scrap Basket - High Impact Polymer

ELECTRICAL n Pre-wired NEMA 4 Control Paneln Patented Operator Sensorn Watertight Conduit /Fittingsn Separate Component Groundingn Thermally Protected Motorn Safety Line Disconnectn 24 Volt Safety Circuitry

PLUMBINGn Corrosion Resistant Componentsn Automatic Water Blendern 24 Volt Solenoid Valvesn Unionsn Check Valvesn Incoming Water Valvesn Non-clogging Pump Designn Pump Intake Screenn Back Flow Prevention Device

ACCESSORIESRemote Start-StopRemote Mounting BracketCorrectional PackageControl Mounting BracketAdditional Scrap Basket

UTILITIES REQUIRED1. Electric service2. 3/4” hot and cold water supply and reduce to 1/2” at connection.3. 2” tank drain.(Specifications subject to change without notice.)

SAMPLE SPECIFICATIONSUnit shall be a Scrap Collector (or Pot/Pan Scrap Collector) scrapping, pre-flushing and food waste collecting system with recirculating water as manufactured by Salvajor.

Model S914 (or P914), ____Volts, 60Hz, ___Phase.

Furnished with a pre-wired HydroLogic control panel, sensor and stainless steel NEMA 4 watertight enclosure.

Salvajor Scrap CollectorTM

MODEL S914 & Model P914 S P E C I F I C A T I O N S

115V 208V 230V, 60 Cycle, 1 Phase

208V 230V 460V, 60 Cycle, 3 Phase

Pump Motor 3/4 HP

VOLTAGES AVAILABLE (SPECIFY EXACT OPERATING VOLTAGE)

FULL LOAD AMPS (SPECIFY EXACT OPERATING VOLTAGE)

The Salvajor Company 4530 East 75th Terrace Kansas City, Missouri 64132-2081, USA 1-800-SALVAJOR (816) 363 -1030 FAX: 1-800-832-9373 www.salvajor.com Email: sales@salvajor.com service@salvajor.com

Manufacturers of Commercial Food Waste Solutions since 1944

1 PHASE 3 PHASE

115V 208V 230V 208V 230V 460V

11 5.5 5.5 3.2 3 1.5

Printed in USAForm No.S&P914 (08-16)

U.S. Pat. No. 7,815,134