multifunction transmitter c 310 - sentronic
TRANSCRIPT
Multifunction transmitterC 310KEY POINTS
Material: ABS V0 as per UL94
Protection: IP65
Display: Graphic from 1 to 4 lines, 240 x 128 px; Size: 86 x 51 mm,Backlit
Height of digits: Values: 10 mm; Units: 5 mm
Cable gland: in polyamide for cables Ø9 mm maximum
Weight: 700 g
● 2 inputs for interchangeable probes● 1 location for interchangeable SPI-2 board● Simultaneous display of 1 to 4 parameters● Trend indicator● 4 visual (dual-color LEDs) and audible alarms● 2 analogue outputs (4 wires) 0/5-10 V or 0/4-20 mA, 2 additional outputs (optional)● 4-relay board (optional)● 24 Vdc/Vac or 115/230 Vac power supply● Outputs diagnostic● Ethernet communication (optional)● MODBUS network RS485 system (optional)● ABS housing with stainless steel front, IP65, with or without backlit graphic display● “¼ turn” system mounting with wall-mount plate
FEATURES OF THE HOUSING
TECHNICAL SPECIFICATIONS
PART NUMBERS● C310-BO : multifunction transmitter, 24 Vac/Vdc power supply, with display● C310-BN : multifunction transmitter, 24 Vac/Vdc power supply, without display
Power supply24 Vac / Vdc ±10%100-240 Vac, 50-60 HzWarning: risk of electric shock
Outputs
2 x 0/4-20 mA or 2 x 0-5/10 V (4 wires)Optional additional outputs: 2 x 0/4-20 mA or 2 x 0-5/10 V (additional consumption for 24 V model: 1 VA / for 115-230 V model: 2 VA)Common mode voltage <30 VACMaximum load: 500 Ohms (0/4-20 mA) / Minimum load: 1 K Ohms (0-5/10 V)
Galvanic isolationInputs (power supply) and outputs (on 115 Vac/230 Vac models)Device fully protected by DOUBLE ISOLATION or REINFORCED ISOLATIONOutputs (on 24 Vac/Vdc models)
Consumption with probe and without option
C310-BO and C310-BN: 6 VAC310-HO and C310-HN: 8 VA(CO2 probe additional consumption for 24 V and 115-230 V models: 2 VA)
Relays (optional) 4 RCR relays 5 A / 230 V (additional consumption for 24 V model: 5 VA / for 115-230 V model: 8 VA)
European directives 2014/30/EU EMC; 2014/35/EU Low Voltage; 2011/65/EU RoHS II; 2012/19/EU WEEE
Electrical connectionsScrew terminal block for cables from 0.05 to 2.5 mm2 or from 30 to 14 AWGCarried out according to the code of good practice
RS485 communication (optional)
Digital: Modbus RTU protocol, configurable communication speed from 2400 to 115200 Bauds
Ethernet communication (optional)
Ethernet communication module allowing transmission, monitoring and maintenance of transmitters via an Ethernet network in 10 BASE-T and 100 BASE-TX LAN/WAN supporting TCP/IP protocol(additional consumption for 24 V and 115-230 V models: 1 VA)
● C310-HO : multifunction transmitter, 115-230 Vac power supply, with display● C310-HN : multifunction transmitter, 115-230 Vac power supply, without display
81 mm158 mm
111
mm
25 m
m
Rugghölzli 2CH - 5453 Busslingen
Tel. +41 (0)56 222 38 18Fax +41 (0)56 222 10 12
[email protected], Support und Service
SENTRONICAG
Audible alarm Buzzer (70 dB at 10 cm)
Environment and type of fluid Air and neutral gases
Conditions of use (°C/%RH/m) From -10 to +50°C. In non-condensing condition. From 0 to 2000 m
Storage temperature From -10 to +70°C
Security Protection class 2; Pollution degree 2; Overvoltage category 2
TECHNICAL SPECIFICATIONS
RELAYS AND ALARMS
The C 310 transmitter has 4 independent and configurable alarms : these are visual and audible alarms and it is possible to couple them with 4 relays (optional).
Available settings: ● Selection of the parameter (pressure, air velocity, temperature,...)● Time-delays duration from 0 to 600 s● Alarm action : rising edge, falling edge, monitoring or state of the transmitter● Operating mode of the relays : negative or positive safety (optional)● Activation of the audible alarm (buzzer) that can be acknowledged by the front keypad (optional)
CONNECTIONS
Cable glandsPressure connection (optional)
Power supply terminal block (c)
LCC-S software connection
Solenoid valve
Analogue outputs (a)(OUT3 and OUT4 are optional)
0/4-
20 m
A –
Cur
rent
0-5/
10 V
- Vo
ltage
GN
D –
Gro
und
Analogue output 1 (OUT1)
GN
D –
Gro
und
Analogue output 2 (OUT2)
(a)
Autozero
Relays board (b) (optional)
Ethernet board (optional)
Type of power supply of the transmitter
Probes connection
0/4-
20 m
A –
Cur
rent
0-5/
10 V
- Vo
ltage
RS 485 connection(d) (optional)
0/4-
20 m
A –
Cur
rent
0-5/
10 V
- Vo
ltage
GN
D –
Gro
und
Analogue output 3 (OUT3)
GN
D –
Gro
und
Analogue output 4 (OUT4)
0/4-
20 m
A –
Cur
rent
0-5/
10 V
- Vo
ltage
Optional
For 24 Vdc/Vac power supply models: For 115 Vac or 230 Vac power supply models: or(c) (c)
Neu
tral (
N)~
Phas
e (L
)~
Neu
tral (
N) -
Phas
e (L
) +
Ope
ratio
nal
grou
ndin
g
SPI-2 board (optional)
NO
: N
orm
ally
ope
n
NC
: N
orm
ally
clo
sed
Relay 1
CO
M :
Com
mon
NO
: N
orm
ally
ope
n
NC
: N
orm
ally
clo
sed
Relay 2
CO
M :
Com
mon
NO
: N
orm
ally
ope
n
NC
: N
orm
ally
clo
sed
Relay 3
CO
M :
Com
mon
NO
: N
orm
ally
ope
n
NC
: N
orm
ally
clo
sed
Relay 4C
OM
: C
omm
on
(b)
A+
B-
Modbus:
1 2 3
(d)
GND
Ope
ratio
nal
grou
ndin
g
Rugghölzli 2CH - 5453 Busslingen
Tel. +41 (0)56 222 38 18Fax +41 (0)56 222 10 12
[email protected], Support und Service
SENTRONICAG
ELECTRICAL CONNECTIONS – as per NFC15-100 Norm
This connection must be made by a formed and qualified technician. Whilst making the connection, the transmitter must not be energized. The presence of a switch or a circuit breaker upstream the device is compulsory.
➢ 0/4-20 mA current output connection:
0/4-20 mA
Regulator display or PLC/BMS
passive type
➢ 0-5/10 V voltage output connection:
➢ For 115 Vac or 230 Vac power supply models:
+-
24 Vdc power supply
+-
➢ For 24 Vdc power supply models:
➢ For 24 Vac power supply models:
24 Vac power supply
N
LL
NPe
230 Vac
LNPe
230 Vac
or
24 Vac power supplyclass II
LN
L
N
LN
24 Vac
LN115/230 Vac power supply
0-5/10 VGND
-+
Regulator display or PLC/BMS
passive type
- +
RS 485 MODBUS PROTOCOL (optional)
Class 310 transmitters can be linked in one network operating on a RS485 home bus.The RS 485 digital communication is a 2-wire network, on which the transmitters are connected in parallel. They are connected to a PLC/BMS via the RTU Modbus communication system. Since the C310 can be configured with the keypad, the MODBUS enables remote configuration, to measure 1 or 2 parameters or to see the status of the alarms...
0/4-20 mA 0-5/10 VGND
LN
24 Vac
POSSIBLE OPTIONAL MEASUREMENTS
The following probes and boards are available as option for C310 transmitters. For further details please see the technical datasheet of probes for class 310 transmitters.
Probes Measuring ranges
Stainless steel or polycarbonate hygrometry / temperature probe From 0 to 100%RH and from -40 to +180°C (according to probe)
Air velocity vane probe: air velocity / temperature / airflow From -5 to 35 m/s (according to probe) / From -20 to +80°C / From 0 to 99 999 m³/h
Air velocity hotwire probe: air velocity / temperature / airflow From 0 to 30 m/s / From -20 to +80°C / from 0 to 99 999 m³/h
Omnidirectional probe: air velocity / temperature From 0 to 5 m/s and from 0 to 50°C
Pt100 1/3 DIN temperature probe From -50 to +180°C / From -20 to +80°C
CO / temperature probe From 0 to 500 ppm and from 0 to 50°C
CO2 / temperature probe From 0 to 20 000 ppm and from 0 to 50°C
Boards Measuring ranges
Pressure / atmospheric pressure From -100 to +10 000 Pa (according to boards) / from 800 to 1100 hPa
Relays 4 relays 3 A with 3-point terminal blocks
Rugghölzli 2CH - 5453 Busslingen
Tel. +41 (0)56 222 38 18Fax +41 (0)56 222 10 12
[email protected], Support und Service
SENTRONICAG
FTan
g –
C31
0 –
27/0
1/20
17 –
RC
S (2
4) P
érig
ueux
349
282
095
Non
-con
tract
ual d
ocum
ent –
We
rese
rve
the
right
to m
odify
the
char
acte
ristic
s of
our
pro
duct
s w
ithou
t prio
r not
ice.
MOUNTING
To install the transmitter on a wall, fix the stainless steel plate to the wall (drilling: Ø8 mm, screws and wall-plugs supplied).Insert the transmitter on the plate (see A on the drawing below) by aligning it at 30°. Rotate the housing in clockwise direction until you heard a “click” which confirms that the transmitter is correctly installed. Open the housing, lock the clamping system of the housing on the plate with the screw (see photo below).To remove the transmitter from the fixing plate, do not forget to remove this screw.
MAINTENANCE
OPTIONS
● LCC-S: configuration software with USB cable● SQR/3 function: (square root extraction) function for the calculation of air velocity and airflow● RS5: RS 485 Protocol Modbus digital output● O2S: 2 additional analogue output● C4R: 4 relays board● CETHE: Ethernet network board● HRP: high resolution (example in pressure: 0.1 Pa) with SPI2-100 board● Calibration certificate
CALIBRATION
Outputs diagnostics: with this function, you can check with a multimeter (or on a regulator/display, or on a PLC/BMS) if the transmitter outputs work properly. The transmitter generates a voltage of 0 V, 5 V and 10 V or a current of 0 mA, 4 mA, 12 mA and 20 mA
Certificate: transmitters are supplied with an individual adjusting certificate and can be supplied with a calibration certificate as an option.
CONFIGURATIONClass 310 transmitters allows you to set all the parameters managed by the transmitter : units, measuring ranges, alarms, outputs, channels... via the different methods shown below: ➢ Via keypad, only on models with display. A code-locking system for keypad guarantees the security of the installation. See configuration manual.➢ Via software (optional): simple and user-friendly. See LCC-S user manual.➢ Via Modbus (optional): configuration of all parameters from your PC, via the supervision or data acquisition software.➢ Via Ethernet (optional): configuration of all parameters from your PC, via the supervision or data acquisition software.
A
A
120 mm
Ø 5,4 mm65 mm
98 m
m 6
5 m
m
316 L stainless steel plateFixing screw of the housing
Only the accessories supplied with the device must be used.
PRECAUTIONS FOR USE
Please always use the device in accordance with its intended use and within parameters described in the technical features in order not to compromise the protection ensured by the device.
ETHERNET BOARD (optional)An Ethernet board can put put on a C310 transmitter allowing for each transmitter to have a specific configurable IP address. So the user can remotely interrogate the transmitter, retrieve data, modify the configuration, ...It is also possible to integrate C310 transmitters into a computer network via the RJ45 connection located at the bottom of the transmitter.
Once returned to KIMO, required waste collection will be assured in the respect of the environment in accordance with European guidelines relating to WEEE.
Avoid aggressive solvents. When cleaning rooms or ducts with products containing formol, protect the the transmitter.
Rugghölzli 2CH - 5453 Busslingen
Tel. +41 (0)56 222 38 18Fax +41 (0)56 222 10 12
[email protected], Support und Service
SENTRONICAG
AMBIENT HYGROMETRY/TEMPERATURE PROBES
Interchangeable hygrometry and ambient temperature probe in stainless steel with stainless steel filter. Standard mounting probe 120 mm length with a watertight connector of 1/4 turn. In option: protective tips, filters. Supplied with adjustment certificate. Ref: SHSI
*All the accuracies indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same conditions, or carried out with calibration compensation.1Calculated value
13 mm
125.45 mm
18.8 mm
74.5 mm
Probes and interchangeable boards for class 310 sensors
➢ Stainless steel hygrometry/temperature probes
1
Ambient hygrometry/temperature probes.................................................................................................... 1Stainless steel hygrometry/temperature probes................................................................................. 1
Remote hygrometry/temperature probes..................................................................................................... 2Stainless steel hygrometry/temperature probes............................................................... ..................2Polycarbonate hygrometry/temperature probes............................................................... ..................2
Temperature probes.....................................................................................................................................3CO
2/temperature probes and CO/temperature............................................................................................ 4
Air velocity probes and temperature............................................................................................................ 4Ø14 mm vane probe...........................................................................................................................4Ø70 mm vane probe...........................................................................................................................5Ø100 mm vane probe.........................................................................................................................5Hot-wire probe.................................................................................................................................... 5Omnidirectional probe.........................................................................................................................6
Extensions for probes.................................................................................................................................. 6Interchangeable boards............................................................................................................................... 6
Pressure boards................................................................................................................................. 6Current/Voltage boards.......................................................................................................................7
Parameter Measuring range Accuracy* Resolution
Temperature Pt100 (°C, °F) From -20 to +80°C ±0.3% of reading ±0.25°C 0.1°C
Wet temperature1 (°Ctw, °F
tw) From -50 to 100°C
tw- 0.1°C
tw
Dewpoint1 (°Ctd, °F
td) From -50 to +100°C
td- 0.1°C
td
Relative humidity (%RH) From 0 to 100%HR Hygrometry: - Accuracy (Repeatability, linearity, hysteresis): ±1.5%RH (from 15°C to 25°C and from 5 to 95%RH) - Factory calibration uncertainty: ±0.88%RH - Temperature dependence: ±0.04 x (T-20) %RH (if T<15°C or T>25°C)
0.1%RH
Absolute humidity1 (g/m3) From 0 to 600 g/m3 - 0.1 g/m3
Enthalpy1 (kJ/kg) C310/CA310: from 0 to 15 000 kJ/kg CPE310: from 0 to 9999 kJ/kg
- C310/CA310: from 0 to 9999.9: 0.1 kJ/kgfrom 10 000 to 15 000: 1 kJ/kg
CPE310: from 0 to 999.9: 0.1 kJ/kgfrom 1000 to 9999: 1 kJ/kg
Combination ration1 (g/kg) C310: from 0 to 10 000 g/kgCA310: from 0 to 9999.9 g/kgCPE310: from 0 to 9999 g/kg
- C310/CA310: 0.1 g/kgCPE310: from 0 to 999.9 g/kg: 0.1 g/kg
from 1000 to 9999 g/kg: 1 g/kg
Rugghölzli 2CH - 5453 Busslingen
Tel. +41 (0)56 222 38 18Fax +41 (0)56 222 10 12
[email protected], Support und Service
SENTRONICAG
Interchangeable hygrometry and temperature probe in polycarbonate with stainless steel filter. Remote probe 150 mm length or 300 mm, 13 mm diameter. White silicone cable 2 m length with watertight connector 1/4 turn. In option : protective tips, filters. Supplied with adjustment certificate.Ref: SHDP-150 (probe 150 mm length) SDHP-300 (probe 300 mm length)
Interchangeable hygrometry and temperature probe in stainless steel with stainless steel filter. Remote probe 150 mm length or 300 mm, 13 mm diameter. White silicone cable 2 m length with watertight connector 1/4 turn. In option : protection socket, filters. Supplied with adjustment certificate.Ref: SHDI-150 (probe 150 mm length) SHDI-300 (probe 300 mm length)
➢ Polycarbonate hygrometry / temperature probe
2
106.45 mm
13 mm
165 mm or 315 mm
18.8 mm
13 mm
151 mm or 301 mm
164.4 mm or 314.5 mm
13 mm
18.8 mm
106.45 mm
13 mm
150 mm or 300 mm
*All the accuracies indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same conditions, or carried out with calibration compensation.1Calculated value
REMOTE HYGROMETRY/TEMPERATURE PROBES
➢ Stainless steel hygrometry/temperature probes
Parameter Measuring range Accuracy* Resolution
Temperature Pt100 (°C, °F) From -20 to +80°C ±0.3% of reading ±0.25°C 0.1°C
Wet temperature1 (°Ctw, °F
tw) From -50 to 100°C
tw- 0.1°C
tw
Dewpoint1 (°Ctd, °F
td) From -50 to +100°C
td±0.6% of reading ±0.5°C
td0.1°C
td
Relative humidity (%RH) From 0 to 100%HR Hygrometry: - Accuracy (Repeatability, linearity, hysteresis): ±1.5%RH (from 15°C to 25°C and from 5 to 95%RH) - Factory calibration uncertainty: ±0.88 %RH - Temperature dependence: ±0.04 x (T-20) %RH (if T<15°C or T>25°C)
0.1%RH
Absolute humidity1 (g/m3) From 0 to 600 g/m3 - 0.1 g/m3
Enthalpy1 (kJ/kg) C310/CA310: from 0 to 15 000 kJ/kg CPE310: from 0 to 9999 kJ/kg
- C310/CA310: from 0 to 9999.9: 0.1 kJ/kgfrom 10 000 to 15 000: 1 kJ/kg
CPE310: from 0 to 999.9: 0.1 kJ/kgfrom 1000 to 9999: 1 kJ/kg
Combination ration1 (g/kg) C310: from 0 to 10 000 g/kgCA310: from 0 to 9999.9 g/kgCPE310: from 0 to 9999 g/kg
- C310/CA310: 0.1 g/kgCPE310: from 0 to 999.9 g/kg: 0.1 g/kg
from 1000 to 9999 g/kg: 1 g/kg
Rugghölzli 2CH - 5453 Busslingen
Tel. +41 (0)56 222 38 18Fax +41 (0)56 222 10 12
[email protected], Support und Service
SENTRONICAG
Interchangeable temperature probe of general use Pt100, 1/3 DIN type STS-13, contact tip 6 mm diameter, 22 mm length. Range from -20 to +80 °C. Direct output on connector for C310 sensors, CPE310 (with adapter) and large display CA310. Supplied with adjustment certificate.Ref: STS-13
Measuring ranges From -20 to +80°C
Accuracy* ±0.3% reading ±0.25°C
Resolution 0.1°C
Interchangeable temperature probe Pt100 1/3 DIN of general use, contact tip 6 mm diameter, 150 mm length, IP65. Grey silicone cable 2 m length with watertight connector 1/4 turn. Supplied with adjustment certificate.Ref: STD-13
Measuring ranges From -50 to +180°C
Accuracy* ±0.3% reading ±0.25°C
Resolution 0.1°C
106.45 mm
18.8 mm
13 mm
6 mm
150 mm
TEMPERATURE PROBES
*All the accuracies indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same conditions, or carried out with calibration compensation.
18.8
mm
118.45 mm
6m
m
13m
m
22 mm
3
Interchangeable adapter for 3-wire Pt100 temperature probe. Allows to plug a 3-wire Pt100 probe to a class 310 sensor. PVC cable, 10 cm length with connector 1/4 turn and 3-point terminal to screw for Pt100 wires output probe.Ref: STA-13
Measuring range According to the probe (maximum measuring range in temperature: from -100 to 400°C)
Accuracy* According to the probe
Resolution 0.1°C
G
+
-
1
2
2'
Rugghölzli 2CH - 5453 Busslingen
Tel. +41 (0)56 222 38 18Fax +41 (0)56 222 10 12
[email protected], Support und Service
SENTRONICAG
AIR VELOCITY AND TEMPERATURE PROBES
Measuring ranges From 0 to 25 m/sFrom -20 to +80°CFrom 0 to 99999 m3/h
Accuracy* Air velocity: from 0.8 to 3 m/s : ±3% of the reading ±0.1 m/s from 3.1 to 25 m/s : ±1% of the reading ±0.3 m/sTemperature Pt100: ± 0.4% reading ± 0.3°CFlow : ± 3% reading or ± 0.03* sheath surface (cm2)
Resolution 0.1 m/s0.1°C0.1 m3/h
Interchangeable air velocity and temperature remote with Ø14 mm vane, 300 mm length, white PVC cable 2 m length with watertight connector 1/4 turn.
106.45 mm
18.8 mm
13 mm
14 mm
312 mm
253 mm
➢ SVH-14 : Ø14 mm vane probe
4*All the accuracies indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same conditions, or carried out with calibration compensation.
CO2 PROBES / TEMPERATURE AND CO/TEMPERATURE
Interchangeable CO2 and temperature probe or CO and temperature in ABS V0. Remote probe 160 mm length, 26 mm diameter. White PVC cable 2 m length
with watertight connector 1/4 turn. Supplied with mounting flange and adjustment certificate.Ref: SCO2 / SCCO
CO2 Probe – temperature CO Probe – temperature
Measuring ranges From 0 to 5000 ppm and from 0 to 50°C (other range available in CO
2 : from 0 to 20 000 ppm)
From 0 to 500 ppm and from 0 to 50°C
Accuracy* CO2: from 0 to 5000 ppm : ±3% of the reading ±50ppm
from 0 to 20 000 ppm : ±5% of the reading±100 ppm
Temperature CTN : ±0.3°C
CO: ±3 ppm or 3% of the measured valueTemperature CTN: ±0.3°C
Resolution 0.1 ppm0.1°C
0.1 ppm0.1°C
126.45 mm
13 mm
18.8 mm
26 mm
144 mm
183 mm
Rugghölzli 2CH - 5453 Busslingen
Tel. +41 (0)56 222 38 18Fax +41 (0)56 222 10 12
[email protected], Support und Service
SENTRONICAG
Measuring ranges From 0 to 30 m/sFrom -20 to +80 °CFrom 0 to 99999 m3/h
Accuracy* Air velocity: from 0 to 3 m/s: ±3% of the reading ±0.03 m/s from 3.1 to 30 m/ : ±3% of the reading ±0.1 m/sTemperature Pt100: ± 0.3% reading ± 0.25 °CFlow: ± 3% reading or ± 0.03* sheath surface (cm2)
Resolution From 0 to 3 m/s: 0.01 m/s; from 3 to 30 m/s: 0.1 m/s0.1 °C0.1 m3/h
Interchangeable air velocity and temperature remote hot-wire probe in stainless steel 300 mm length, 8 mm diameter, white PVC cable 2 m length with watertight connector 1/4 turn.
106.45 mm
18.8 mm
13 mm
8.6 mm
282 mm
8 mm
➢ SVS : hot-wire probe
5*All the accuracies indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same conditions, or carried out with calibration compensation.
Interchangeable air velocity and temperature remote probe with Ø 70 mm vane, 200 mm length, white PVC cable 2 m length with watertight connector 1/4 turn.
Measuring ranges From -5 to 35 m/sFrom -20 to +80 °CFrom 0 to 99999 m3/h
Accuracy* Air velocity: from 0.4 to 3 m/s: ±3% of the reading ±0.1 m/s from 3.1 to 35 m/s: ±1% of the reading ±0.3 m/sTemperature Pt100: ± 0.4% reading ± 0.3 °CFlow: ± 3% reading or ± 0.03* sheath surface (cm2)
Resolution 0.1 m/s / 0.1 °C / 0.1 m3/h
106.45 mm
18.8 mm
13 mm
13 mm
306.5 mm
77.2 mm
200 mm
Interchangeable air velocity and temperature remote probe with Ø 100 mm vane, 200 mm length, white PVC cable 2 m length with watertight connector 1/4 turn.
Measuring ranges From -5 to 35 m/sFrom -20 to +80 °CFrom 0 to 99999 m3/h
Accuracy* Air velocity: from 0.3 to 3 m/s: ±3% of the reading ±0.1m/s from 3.1 to 35 m/s: ±1% of the reading ±0.3 m/sTemperature Pt100: ± 0.4% reading ± 0.3CFlow: ± 3% reading or ± 0.03* sheath surface (cm2)
Resolution From -5 to -3 m/s: 0.1 m/s; from -3 to 3 m/s: 0.01 m/s; from 3 to 35 m/s: 0.1 m/s0.1 °C0.1 m3/h
106.45 mm
13 mm
18.8 mm
13 mm
335.4 m
106.1 mm
200 mm
➢ SVH-70 : Ø70 mm vane probe
➢ SVH-100 : probe Ø100 mm wind vane
Rugghölzli 2CH - 5453 Busslingen
Tel. +41 (0)56 222 38 18Fax +41 (0)56 222 10 12
[email protected], Support und Service
SENTRONICAG
Interchangeable pressure board with electro-valve and terminal for K thermocouple probe for C310 and CA310 sensors. Supplied with pressure fitting and silicone tubes.Ref: SPI2-100 SPI2-500 SPI2-1000 SPI2-10000
Measuring ranges SPI2-100: from -100 to +100 Pa SPI2-500: from -500 to +500 PaSPI2-1000: from -1000 to +1000 PaSPI2-10000: from -10000 to +10000 Pa
Accuracy* SPI2-100: ±0.2% of the reading ±0.8PaSPI2-500: ±0.2% of the reading ±2PaSPI2-1000: ±0.2% of the reading ±2PaSPI2-10000: ±0.2% of the reading ±10Pa
Admissible removal SPI2-100 / SPI2-500 / SPI2-1000: 21 000 Pa SPI2-10000: 69 000 Pa
Units and resolution 1 Pa0.1 mmH
2O
0.01 mbar0.01 inWG0.01 mmHG0.1daPa0.001 kPa0.01 hPa
● Pressure
Measuring ranges From -200 to +1300 °C (according to the probe)
Accuracy* ±1.1 °C or ±0.4% of the read value1
Units and resolution 0.1 °C 0.1 °F
● Temperature K thermocouple
INTERCHANGEABLE BOARDS➢ Pressure boards SPI-2
6
*All the accuracies indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same conditions, or carried out with calibration compensation.1The accuracy is expressed by a gap in °C, or by a percentage of the read value. Only the bigger value is held.
Interchangeable air velocity and temperature remote omnidirectional hot-wire probe in stainless steel 300 mm length, 8mm diameter, white PVC cable 2 m length with watertight connector 1/4 turn. Supplied with carrying case and tripod.
Measuring ranges From 0 to 5 m/sFrom 0 to +50 °C
Accuracy* Air velocity: ± 3% reading ± 0.05 m/sTemperature Pt100 1/3 DIN: ± 0.3% reading ± 0.25 °C
Resolution 0.01 m/s0.1 °C
106.45 mm
18.8 mm
13 mm
364 mm
81 mm
8 mm
R310-5: Extension of 5 m for interchangeable probes class 310
R310-10: Extension of 10 m for interchangeable probes class 310
➢ SVO : omnidirectional probe
EXTENSIONS FOR PROBES
Rugghölzli 2CH - 5453 Busslingen
Tel. +41 (0)56 222 38 18Fax +41 (0)56 222 10 12
[email protected], Support und Service
SENTRONICAG
7
Interchangeable board, 3 current / voltage analogic input: 0-20 mA / 4-20 mA et 0-2,5 V / 0-5 V / 0-10 V, with terminal, CA310 sensor.Ref: MVA
Example of MVA current / voltage board on CA310 sensor
➢ Current / Voltage boards
Measuring ranges 0 – 20 mA4 – 20 mA0 – 2.5 V0 – 5 V0 – 10 V
Accuracy* 0 – 20 mA : ± 0.01 mA4 – 20 mA: ± 0.01 mA0 – 2.5 V: ± 0.002 V0 – 5 V: ± 0.005 V0 – 10 V: ± 0.010 V
*All the accuracies indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same conditions, or carried out with calibration compensation.
Example of SPI2 pressure board on C310 sensor
Terminal for K thermocouple probe
Relay board C4R on C310 sensor
These pressure boards SPI2 for C310 and CA310 sensors have a temperature compensation of the gain from 0 to 50 °C and an auto-calibration process which guarantee over time an excellent stability and a perfect reliability of the measurement as much in low as high range.Auto-calibration principle : the microchip of the sensor manages an electro-valve which compensates possible remotes of the sensitive element over time. The compensation is insured by a permanent adjustment of the zero. The differential pressure measurement is then independent from the environmental conditions of the sensor.
Electro-valve lifetime: 100 millions of cyclesAdvantage: no zero remotePeriodicity of the auto-calibration: detachable or from 1 to 60 min.
Interchangeable atmospheric pressure board for C310 and CA310 sensors, range 800-1100 hPa. Supplied with pressure fitting and silicone tube.Ref: SPI2-ATMO
Measuring ranges From 800 to 1100 hPa
Accuracy* ±2 hPa
Units and resolution 0.1mbar0.1mmHG0.1hPa
Rugghölzli 2CH - 5453 Busslingen
Tel. +41 (0)56 222 38 18Fax +41 (0)56 222 10 12
[email protected], Support und Service
SENTRONICAG