multi purpose machine model: mp250 operating …
TRANSCRIPT
MULTI PURPOSE MACHINE
MODEL: MP250
OPERATING INSTRUCTION
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
ALL WARNINGS AND INSTRUCTIONS BEFORE USE
PAN-SINO MACHINE BUILDING CO., LTD.
1. Features & Controls
C
B
A
X w V
Ref. Description
A Emergency stop switch
B Handle A
C Handle B
D 3 Jaw Chuck
E Tool-post
F Tool-post clamp Lever
G Emergency stop switch
H Speed adjusting switch
I DC motor
J Electric box
K Fine feeding wheel
L Feeding handles
2
Ref.
M
N
0
p
Q
R
s
T
u
V
w
X
u
J K
T
Description
Clamping lever
Tailstock clamping lever
Tailstock
Tailstock hand-wheel
Tailstock clamping nut
Base of tailstock
Lead-screw cover
Compound slide
Half nut lever
Cross slide hand-wheel
Saddle hand-wheel
Forward-stop-reverse
M
N
0
p
Q
R
s
2. Specifications
Driven ByMax. Swing over BedMax. Swing over CarriageDistance between Two CentersSpindle BoreSpindle TaperSteps & Range of Spindle SpeedKinds & Range of Metric ThreadsKinds & Range of Inch ThreadsKinds & Range of Module threadsSteps & Amount of Longitudinal FeedsSize of Cutting Tool ShankSwivel of Tool PostCompound Slide MovementTool Post MovementMax. Longitudinal Travel of Tool PostMax. Travel of Cross SlldeMax. Longitudinal Travel of SaddleTaper of Tailstock QuillMax. Travel of Tailstock QuillMotor Power for LatheDrill/Mill Spindle Speed ( Variable Speed )Taper of Drill/Mill SpindleMax. Capacity of DrillingMax. Capacity of End MillingMax. Capacity of Face MillingWorking Table SizeSpindle StrokeSpindle Nose to TableSwivel of Drill/Mill HeadstockMotor Power for Drill/MillNet WeightOverall Dimension
Standard Accessory:
"0 "Type BeltSelf-centering 3 Jaw Chuck di 125 mmCenters MT 2 and MT 4Tool-Post SpannerSet of Spanner & WrenchesDrilling Chuck 13 mmOil KitChange Gears
3
2 Pieces1 Set2 Pieces1 Piece8 Pieces
1 Set1 Set15 Sets
Full Gears250 mm
150 mm50) /,00 mm
26 mmMT 4
8 I 140 -1 800 rpm20 I 0.2 - 3.5 mm
20 I 8 - 56 tpi10 I 0.2 -1.25 mp2 I 0.05; 0.10 mm
12 mm±45°
0.05 mm0.05 mm
70mm115 mm
550 I 800 mmMT 2
50mm550W
100 - 2500 rpmMT 3
13 mm16 mm30 mm
150 x 300 mm180 mm
280mm±45°
400w195 I 235 kg
1200 I 1500x680x880 mm
3. Transmission System
3.1 Transmission system
Fig.2
3.2. Handle position for change spindle speed
� 140 200 600 900
Handle Position
bd b8 8cf 88 0/min
280 400 1200 1800
Fig 3 handle position
4
3.3 Diagrammatic Sketch of Gear Transmission Refer to Fig 4 for the gear of longitudinal feed and the transmission system O 1 screw thread. The feed
0. 1 change gear installed in the machine is O 10 rpm. Some times change (esp. in inch screw thread) run into
intermediate shaft of the spindle box. It is solved that isolated cover supplied in the standard accessories is
mounted in the middle of 8-C wheel.
A
B
C
Output Spindle from Spindle Stock
Shaft of Middle Pulley
Frame of Change Gear
Fig 4 DIAGRAMMATIC SKETCH OF GEAR TRANSMISSION
Table 1 for the change gear needed for different feed, and threading pitch, and the change gear
system.
TABLE 1
Metric threads Charter
mm 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.6 0.7 0.751 0.8 o.9 I 1 1.25 1.5 11.75 2 2.5 3 1 3.5
30 55 30 35 40 45 50 60 70 40 60 50 70 75 70
B 120 75 80 I 75 35 45 35 I 30 110 110 80
80 50 120 80 120
D 75 110 75 60 50 I 45 30 35 I 30 60
Inch Threads Charter
1/ n 8 9 1 O 11 12 13 14 16 18 20 22 24 26 28 32 36 40 48 52 56
A 60 40 50 40
B 40 60 75 60 120
C 127
D 40 45 50 55 60 65 70 80 45 50 55 60 65 70 80 45 50 60 65 70
5
Dscription of Gear, Screw, Nut Used in All Parts
Part Index
Headstock 1
2
3
4
5
6
7
8
9
10
11
qhange gear frame 12
13
14
15
16
17
18
Change gear frame 19
20
21
22
23
24
25
of the Machine { 1 )
Module Description Tooth
& Pitch
gear 62 M=1.5
duplex gear 28 M=1.5
35 M=1.5
gear 55 M=1.5
gear 55 M=1.5
gear 20 M=1.5x=0.52
gear 45 M=1.5
duplex gear 28 M=1.5
52 M=1.5
gear 45 M=1.25
gear 60 M=1.25
gear spindle 20 M=1.25
gear 60 M=1.25
change gear 30 M=1
change gear 35 M=1
change gear 40 M=1
change gear 45 M=1
change gear 50 M=1
change gear 55 M=1
change gear 60 M=1
change gear 65 M=1
change gear 70 M=1
change gear 75 M=1
change gear 80 M=1
change gear 110 M=1
change gear 120 M=1
change gear 127 M=1
6
Pressure
angle
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
20°
See Fig. 2
Material
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
Dscription of Gear, Screw, Nut Used in All Parts
Part Index
Feeding Box 26
27
28
29
Apron 30
31
32
Bed Gap 33
34
Tool Post 35
36
Tailstock 37
38
Drill I Mill Head 39
40
41
42
43
44
45
46
of the Machine ( 2)
Module & Description Tooth
Pitch
clutch
gear spindle 15 M=1
gear 53 M=1
gear spindle 13 M=1.5
rack 107 M=1.5
Lead-screw 1 t=3
nut 1 t=3
Lead-screw 1 2 (Turn left)
nut 1 2 (Turn left)
bolt 1 2
nut 1 2
bolt 1 2 (Turn left)
nut 1 2 (Turn left)
rack 70 M=1
gear spindle 14 M=1
worm bolt 1 Mn= 1
helical gear 29 Mn=1
duplex gear 29 M=2 .25x=O. 38
21 M=2.25
duplex gear 20 M=2.25
12 M=2.25x=0.38
gear 30 M=1.5
gear 14 M=1.5
7
See Fig. 2
Pressure Material
angle
45
20° 45
20° 45
20° 45
20° 45
30° 45
30° ZQSn6-6-3
30° 45
30° ZQSn6-6-3
30° 45
30° ZQSn6-6-3
30° 45
30° ZQSn6-6-3
20° 45
20° 45
20° 45
20° 45
20° HT200
20° HT200
Harden 20°
Nylon66
Harden 20°
Nylon66
20° 45
20° HT200
4. Installation and Test Run
4.1 Transport and installation
4.1.1 All the standard accessories, optional accessories and technical documents of the machine are packed in
the same box.
4.1.2 Having unpacked the box, you should first of all check the appearance of the machine and see whether all
the standard and optional accessories accompanied with the machine are complete there according to the
packing list.
4.1.3 As the machine is removed out of the unpacked box, the saddle of the machine should be clamped close
up to the tailstock. The spindle box for drilling work should be tightly locked close up to the column. <p20
handling bar attached the hole back of the machine bed and tied with wire rope. During hoisting and
transporting the machine, you should pay a more attention to the centre of it's gravity to avoid it from
inclination and occurrence of accidents.
4.1.4 The bench type of machine must be installed on a rigid flat-plate iron and wood, and fixed with ground bolt
and nut please see Fig 6 for the dimension of installation site of ground bolt and of the machine.
4.1.5 Please see Fig 6-1 for the installation diagram of cutting machine with base frame. It's never allowed to
install the machine on irrigate wood table so as to avoid the machine from vibration when it starts running,
and this will have on the use of the machine and the precision of its operation.
4.1.6 The sliding surface and the unpainted parts of the machine are all oil sealed and coated with the
anti-rusting. Before the installation, you must wipe away the grease and the oil seal and then completely
clean them with anti-fire deter great the sliding surface. You must also be carefully the spindle box.
4.1. 7 While installing the machine, you must use a level gauge to calibrate the mounting level of the machine
and the flatness of the guide rail for fuming work.
4.1.8 To install drilling/milling headstock: Stand the drilling/milling head with column to side of machine bed and
fix it by position set pin, hexagon screws.
4.2 Test Run
4.2.1 After having calibrated the mounting level of the machine, you should fill the spindle box with No. 10 to No.
20filted machine oil up to the oil level indicator on the end surface of the
headstock. And you should also fully fill up the oil filler points at the different parts of the machine with
lubrication oil next, you should check all the operating handles to see whether they work properly and
reliably, the tightness of guide way is proper for its movement. If the tightness of tool slide and cross slide
of tool rest is not proper, please make an adjustment with shim or plug irm
4.2.2 Prior to the test run of the machine, also you must make a careful and through check over all the switches
of the electrical motor and the safety insulation of the electrical appliance. And you must connect the
ground wire to ground screw to ground screw so as to avoid the current and other accidents because of
the damage of electric circuit during the transportation.
4.2.3 Lathe function test:
1. Tune the knob SA 1 of composed switch to' 1 ' ( for lathe running), the green indicator is brighten.
2. Open the cover of composed switch and confirm the running direction ' Forwarding' or' Reversing',
close door of change gear box and chuck protection cover thus push green color knob for spindle run.
3. The electric motor will be stopped if opened door of change gear box or chuck protection cover while
8
the machine Motor will be started closed door or cover
4 Beginning running, to switch the speed at lowest class and run 20 minutes after that could be changed
to high speed step by step if lowest running no defect.
5. Be stopped running for changed speed otherwise be injured gears.
4.2.4 Drilling & Milling function test
1. Turn the knob SA 1 of composed switch to ' 2 ' ( for drilling/milling ), the green indicator is brighten.
2. Push the knob of emergency stop switch SB to arrow, open the switch cover, the red indictor brighten
3. Turn the knob of speed to 'O', the indictor lighting is changed from red to green and then turn the knob
of speed to any designed speed.
4. Power is stopped while pushed emergency switch or overload indictor 'HL2' in red brighten. For
re-starting motor, should be turned knob of speed to 'O' again
5 Operation
5.1 Spindle
en ,.o
You can remove handle(12, 13)according to Fig 3 of Handle Position For Control Spindle Rotating Speed when
you need the spindle speed in processing the work If the gears can't bite each other. Please turn the 3-jaw
chucks by hand until the gear can bite can't turn over when the bigger slide rest is at the position of under the
chuck.
5,2 Feed Box
Switch (2) is used to operate the start, stop, forward and reverse motion of the electrical motor, and to drive the
spindle to make the corresponding motion. The left red big knob(1 )is used to urgency stop. The electric is cut up
when you push knob. The electric is passed through when you push the knob. The electric is passed through
when you push the knob bouncing. The feed box can add screw thread clutch handle(14)according to user's
optional demands. The screw thread mechani.sm transmit to stop when the wheel is at the position "separate"
We can use wheel( 15)to transmit the screw by hand. At the same time you put the wheel of apron at the position
"close".
ft.pron
Set the switch lever of clasp nut(4) at position "open" and turn handle wheel(3),you can make a manual
longitudinal movement of the apron and the machine saddle. When you turn the inner and external cylindrical
surface and cut the thread, you must set the switch lever (4) at the position close so that you are offered the
maneuver Longitudinal feed ancl the threading. The needed feed and screw pitch can get by changing gear
A.B.C.D. according to Change Gear Table in the spindle box of the machine or Table 1.The machine can turn
metric and inch screw thread 20 kinds each, module screw thread 10 kinds. There is blank space in metric screw
pitch "B.C'' in metric screw pitch "B.C'' in Table. You can fix a proper gear Link mechanism in the intermediate
shafl when there is no stable No. of teeth or gears.
9
5.4 Tailstock
5.4.1 Hex nut(5) is used to clamp the tailstock onto the machine bed loose lever(7),you can turn Hand wheel(6)
so that tailstock sleeve can telescopically move forward and backward. The movement of sleeve can be
read out from the dial indicator.
Each scale on the dial indicator is for 0 .0 5mm. You must fasten lever (7) by hand again to fix the position
of sleeve when the tailstock moves to the required position.
5.4.2 You can adjust the horizontal coincidence of the axis of tailstock sleeve and the axis of spindle by the
help of the screws in front and at back of the pad under the tailstock.
5.5 Saddle and tool post:
Turn lever (8), you can move the slide of top rest. Lever (9) is used to fasten the tool rest. Only when Lever
(9) is loosed, the tool rest is able to turn counter clock-wise. The slide of top rest can rotate %p45%d so as to
turn the inner and external taper surface. Lever (10) is a transverse feed lever. Hex nut (1 1) is used to fix the
saddle on the bed. Attention: When carrying out the operation of turning the end surface and hole, you must turn
the nut tightly to assure the working precision accuracy of a work piece to be machined.
5.6 Drilling & Milling
5.6.1 Lose the two pieces screw (M8 X 20), swivel 90 ° to move down tool-post and discharge the 4 pieces
screw (M8 X 20) from slide plate.
5.6.2 Fix the accessory on working table ( compound slide) by 4 pieces screw ( M8 X20 ).
5.6.3 Discharge the protection cover from top of drilling/milling spindle and than put the bush and spacer on the
top of spindle for fixing cutting tool by draw bar.
5.6. 4 Fix the work-piece on working table and adjust center point for machining.
5.6.5 For machining tilt hole or surface, be lose the nut ( M2 4) on column and adjust to the requested angel then
to fix the nut.
6. Maintenance and Lubrication
You must often maintain the machine in use so that it can keep a high working accuracy for a long-term,
increase the longer use life, and produce the satisfactory work piece with high accuracy.
6.1 The day after the machine is put into normal use ,it is necessary to change the lube in headstock. To do
this , you are only needed to turn off the screw of oil drain plug under the front side of headstock to draw off
the lube filled in for test run, to carefully wash out the reside with coat and to fill the headstock with a certain
amount of lube again, From then on, the lubrication oil should be changed at regular intervals. Please see
the regulations in Table 3 for further details.
6.2 Every day before work, you should lubricate the machine according to the requirements of the machine for
lubrication. And you should often chec,k the oil level of the spindle box. If the lube drops down below the oil
level glass, you should fill the spindle box with lube up to the same height of the oil lever. But never be
allowed to fill it up, with lube in order to avoid the overflow of lube.
6.3 In use, he chip falling onto the sliding surface should be cleaned out in good time to prevent the chip from
falling down between the sliding surface of the saddle rail on the machine bed, and to prevent it from
damaging those surface. You must clean and wash the four anti-dusting felts attached on both ends of the
saddle at regular intervals in order to keep them having a fine effect of anti-rusting.
6.4 After having done the work every day, you should immediately clean out the chip. And you should wipe all
the parts of the machine, and spread the machine oil on the sliding surface of guide rail and the open
surface of non-working range so as to keep them from rust.
10
6.5 In order to keep a high working accuracy of the machine, you should take special care of the center, the
stop plane on the chuck of spindle, the sliding guide rail, the inner tapered hole of spindle ,and the
installation plane of slide plate. And you must prevent the machinery of all these parts from being damaged
and worn because of the unreasonable use.
No
1
2
3
4
5
6
7
8
9
10
�:---- ___ ___ _
Fig; 7 DIAGRAMMATIC OF LUBRITION POSITION
Machine part Position Method Machine oil Period
Spindle box Gear, bearing 10#-20# 1st: 10 days after running
spray Regular: every 60 days
Saddle guide way By oil gun 10#-2Q# Every day
Tool slide Lead-screw By oil gun 1Q#-2Q# Every day
tail stock T tailstock sleeve By oil gun 1 Q#-2Q# Every morning & afternoon
lead screw screw By oil gun 1 Q#-20# Every m'orning & afternoon
Cross slide screw By oil gun 10#-20# Every morning & afternoon
Drill/mill head Teeth Rock Grease Every three month
Drill/mill head Teeth Rock 10#-2Q# Every 10 days
Drill/mill head Worm Gear Grease Every three month
Each time before work in all the visible sliding surface
11
7. Electrical Equipment7.1 This machine has been driven by the electrical motor. The main switch is of NVR switch which controls the
forward motion, reverse motion, start and stop of the spindle.
The motor is 0.55kw, 230v, 50HZ, 1400r.p.m. For connection of the switch of electrical motor to the power
supply, please see the electric diagram. The machine electric has open stop and urgency stop button.
7.2 When making the installation and using the equipment, user must carefully check part of the
equipment according to the technical safety regulation. User should connect the ground wire at the same
time of connecting to the power supply, and check the safety insulation before use.
N/0 C
l'1•1S0-·1o
U I N
AC;1 ?0V/i.'!,OV
50Hz/60Hz
LX1
BRNCK LATHB
LA i7 BLl!CTAIC DIACU.M
MILLING/ DRILLING
mcmc DIAGm
C t·.J/ [J
iJ2A020 I
Fig.8
12
11 Kl