Mould ReleaseMouldReleaseMouldRelease

Sydney Ph: (+61 2) 9938 7222 Fax: (+61 2) 9938 5826Melbourne Ph: (+61 3) 9550 5656 Fax: (+61 3) 9950 5651Brisbane Ph: (+61 7) 3271 3944 Fax: (+61 7) 3271 3603Gold Coast Ph: (+61 7) 5563 7771 Fax: (+61 7) 5563 7888

Auckland Ph: (+64 9) 838 7195 Fax: (+64 9) 837 1035Penrose Ph: (+64 9) 579 2029 Fax: (+64 9) 571 0542Christchurch Ph: (+64 9) 366 0409 Fax: (+64 9) 377 2523

Adelaide Ph: (+61 8) 8234 9499 Fax: (+61 8) 9234 9490Perth Ph: (+61 8) 9455 1972 Fax: (+61 8) 9455 1012Cairns Ph: (+61 7) 4035 2126 Fax: (+61 7) 4035 2125

Formulated exclusively for the Fibreglass ReinforcedPlastic and Cultured Marble Industries.

COMPOUNDS

POLISHES

RELEASES

A complete line of economical, professional quality mould releaseproducts that facilitates production, saving time, money, as they minimisemould process problems.

3-STAR MOULD RELEASE PRODUCTS

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

SEMI-PERMANENT RELEASENEW OR RECONDITIONED MOULD PREP GUIDE

POLYESTER MOULDED PARTS

STEP 1 Remove all contaminates and previously used releases from mould surface with the TR-905 SOLVENT CLEANER.Saturate cloth with the 905 Solvent and wipe onto sections or areas of the mould. Allow sufficient time while area isstill wet to follow and wipe dry with a clean cotton cloth. Turn and change cloth frequently to absorb and pick-upcontaminates. REPEAT if necessary until MOULD SURFACE is thoroughly cleaned and wiped dry. On NEW orRECONDITIONED MOULDS that have been buffed with a polishing or buffing compound, first water wash to removethe buffing compound residue and wipe completely dry. Then clean thoroughly with the 905 SOLVENT CLEANER asmentioned above. Refer to product data sheet.

STEP 2 Apply 1-2 coats of TR-910 sealer (2 coats for uniform coverage or if porosity may be present). Allow 15-20 minutescure between coats and 30 minutes after final coat, preferably longer if schedule permits. See product data sheet forapplication.

STEP 3 Apply 2 coats of TR-900 Release (4 coats if TR-910 Sealer is omitted). Allow 5-10 minutes cure between applicationsand after final coat. Wet or dampen a clean lint-free cotton cloth with the release and apply an even wet coat on asmall area of the mould surface (approx. 2 x 2).

Avoid heavy application on cloth that is heavily soaked or dripping wet. While surface is still wet, gently wipe drywith a separate clean, dry cotton cloth. Turn or change cloth as needed to one end of the mould and over-lap slightlyeach small previously applied area until mould is complete. Apply the 2nd or subsequent coats in the same manner.See product data sheet for additional information. Recommend trial of the TR-920 or TR-930 as replacement for theTR-900 where MOULD GEOMETRY requires some horizontal pull when demoulding and added slip action is required.

STEP 4 Apply the TR-900 Series Release again after the first 2 pulls or releases. Then proceed with your multiple Releases andapply only as needed setting up a schedule you have achieved or determined when re-application is required. Anyminor scratches or abrasion marks will have to be treated again at first notice. Apply another coat of Release onaffected area. Any patched or repair areas should be taken through all steps and sufficient over lap of area to provideuniform release & coverage. Allow TR-910 Sealer longer cure (1-2 hours at room temperature) on patched or repairedareas.

NOTE Always use a lint-free all cotton cloth (preferably white) when applying the solvent cleaner 905, sealer 910 & 900 seriesrelease. No synthetic cloth blends and use separate rags for the cleaner, sealer & release. Avoid any contamination ofrags and/or release container. The container must be kept closed when not in use. Material is moisture sensitive andwill exhibit premature reaction if container is left open excessively. Avoid contamination when refilling previously usedcontainers or transferring to other containers.

TR-900 Series

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

TR-900 Series

THERMOSET RELEASE SYSTEMLIQUID SEMI-PERMANENT RELEASE

DESCRIPTION:

TR-900 is a high-temp semi-permanent release coating which dries rapidly under atmospheric condition, bonding an ultra thinclear release film to the mould surface. Exceptional multiple releases per application for various polyester moulding processesand other resin fiberglass fabrication.

PRODUCT FEATURES:

Excellent hi-temp properties (Thermally Stable 700F)

Multiple release per application

Rapid cure time speeds production cycle

No pre-release or transfer

Wipes to high gloss finish

Easily recoats without build-up

SUGGESTED USES:

An effective multiple release agent for the FRP and related moulders.

Open mould hand or spray lay-up

Compression moulding

Injection moulded parts

Vacuum bag

Resin transfer moulding

APPLICATION:

Always use and apply with a clean, lint-free all cotton cloth (no synthetic blends). Clean mould surface thoroughly of all previousrelease agents and sealers using the TR-905 mould prep solvent. Surface should be completely dry and free of anycontaminates. Apply TR-900 by wiping a thin wet coat onto a small area (approx 3 x 3ft) of the mould surface starting at anend point of the mould. (Do not apply heavily or excessively wet). While the release film is still wet, wipe gently with anotherclean dry cotton cloth, turning and changing cloths as required for proper drying. Avoid excessive hard rubbing or wiping ofthe treated surface which ensures a more uniform and effective film deposit. Apply each application overlapping the previoussmall area until the entire mould surface is complete. Repeat this for 3-4 coats to the entire mould surface. Cure time of therelease film at room temp. (75F) is approximately 5-10 minutes. A touch-up coat is recommended for the first 2-3 initialreleases to maximize mould conditioning and durability. When spraying, use a dry air source or airless spray, applying in athin continuous smooth film, avoiding excess flooding or runs. Wipe with a clean dry cotton cloth as noted in wipe application.

NOTE: Recommended use of the TR-910 SEALER for more porous or rough Mould Surfaces and maximum performance of the TR-900 RELEASE.

SEA POWER MOULD RELEASES GEL-GLOSS NO-STREAK FAUCET BRITE

TR-900 Multi-Pull

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

TR-900 Multi-Pull

LIQUID SEMI-PERMANENT RELEASE

DESCRIPTION:TR-910 Sealer is a resilient moisture cure film-forming base coat which acts to seal the mould surfacebefore application of the TR-900 SERIES semi-permanent release agents.

PRODUCT FEATURES:Hi-temperature properties (Thermally stable 900F)Protects against STYRENE attack and maximizes performance of the TR-900, 920 & 930Liquid Semi-permanent Release agentsAids break-in release and seals porosityMoisture cure which adheres well to the mould surface with no transferCompatible with most release agents

SUGGESTED USES:A Base coat or Sealer applied to Fiberglass, metal or Composite tooling prior to application of the TR-900,920 & 930 Releases. Recommended for all types of POLYESTER moulding, EPOXY moulding and otherTHERMOSET MOULDED fiberglass or Graphite Reinforced applications.

Clean MOULD SURFACE thoroughly of all previous sealers and release agents using TR-905 Mould PrepSOLVENT. Light abrasive compounding may be necessary to remove the various types of release agentsor sealers previously used. After compounding, first water wash and wipe dry to remove any compoundresidue. Then completely clean the mould surface with the TR-905 Mould Prep Solvent. See 905 ProductData Sheet.

Apply the TR-910 Sealer to a small area (approx 3 x 3) in a thin wet continuous film. While still wet,gently wipe dry with a clean, lint free cotton cloth. Start at one end of mould surface and continue untilentire mould has been sealed. Apply a second coat to ensure uniform coverage or for more poroussurfaces. Allow mould to stand or sealer to cure a minimum of 20-30 minutes between application orbefore using the TR-900, 920 or 930 release agents. For maximum high temperature mouldingperformance cure sealer at 250F for 1 hour or allow longer ambient temperature cure of 2-3 hours. Whenspraying, use a dry air source or airless spray, applying in a thin continuous smooth film, avoiding excessflooding or runs. Keep spray tip approximately 10-15 inches from mould surface. While still wet, gentlywipe dry with a clean lint free cotton cloth as noted in wipe application.

SEA POWER MOULD RELEASES GEL-GLOSS NO-STREAK FAUCET BRITE

TR-910 Sealer

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

TR-910 Sealer

SOLVENT

A proprietary solvent mixture to remove wax, oils and other surface contaminates from reinforcedpolyester tooling and other hard surface moulds.

Recommended for preparation and cleaning of mould surface prior to application of TR-900 Semi-permanent RELEASE or the TR-910 SEALER.

APPLICATION:Apply TR 905 Solvent to mould surface using a clean cotton cloth working an area sufficient to stay wetdissolving previously used wax or similar releases. While still wet or dissolved in mould cleaner, wipe drywith another clean dry cotton cloth. Repeat as necessary until mould is thoroughly cleaned and dry cottoncloth. Repeat as necessary until mould is thoroughly cleaned and dry. The mould prep cleaner should beused after the buffing compound to remove any residue remaining on the mould surface. The mouldsurface should always be wiped dry prior to use of the TR-900 RELEASE or TR-910 Mould SEALER.

STORAGE AND HANDLING:TR-905 mould prep cleaner is flammable (flash point 34F). Keep away from heat, sparks and open flame.Close container after using and keep stored in a cool area. Avoid prolonged exposure to breathing andcontact with skin. Use only with adequate ventilation. Use of respirators or fresh air masks in confinedareas.

FOR INDUSTRIAL USE ONLY:KEEP OUT OF REACH OF CHILDRENDO NOT TAKE INTERNALLY

The information contained herein is based on tests considered to be reliable and accurate. Because of the wide variance of associated materials and conditions.

However, no warranty is expressed or implied. Each user is encouraged to prepare a test part for his particular application.

SEA POWER MOULD RELEASES GEL-GLOSS NO-STREAK FAUCET BRITE

TR-905 Mould Prep Cleaner

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

TR-905 Mould Prep Cleaner

THERMOSET RELEASE SYSTEMLIQUID SEMI-PERMANENT RELEASE

DESCRIPTION:

TR-920 is a high-temp multiple capability semi-permanent release coating which cures under atmospheric condition, bondinga durable thin clear release coating to the mould surface. Multiple releases per application for polyester, epoxy, polyimides,BMC, SMC, and various other advanced resins in fiberglass or graphite composite moulding processes, thermoplastic Rotationaland Rubber moulding.

PRODUCT FEATURES:

Excellent hi-temp properties (Thermally Stable 700F)

Multiple release per application

Ease of application and fast cure time

No pre-release or transfer

Wipes to a gloss finish

Easily recoats without build-up

SUGGESTED USES:

An effective multiple release agent for the FRP and related moulders.

Open mould hand or spray lay-up

Compression moulding

Injection moulded parts

Vacuum bag

Resin transfer moulding (RTM)

APPLICATION:

Always use and apply with a clean, lint-free all cotton cloth (no synthetic blends). Clean mould surface thoroughly of all previousrelease agents and sealers using the TR-905 mould prep solvent. Surface should be completely dry and free of anycontaminates. Apply TR-920 by wiping a thin wet coat onto a small area (approx 3 x 3ft) of the mould surface starting at anend point of the mould. While the release film is still wet, wipe gently with another clean dry cotton cloth, turning and changingcloths as required for proper drying. Avoid excessive hard rubbing or wiping of the treated surface which ensures a moreuniform and effective film deposit. Apply each application overlapping the previous small area until the entire mould surface iscomplete. Repeat this for 3-4 coats to the entire mould surface. Cure time of the release film at room temp. (75F) isapproximately 20-30 minutes (15 minutes at 250F). A touch-up coat is recommended for the first 2-3 initial releases tomaximize mould conditioning and durability. When spraying, use a dry air source or airless spray, applying in a thincontinuous smooth film, avoiding excess flooding or runs. Wipe with a clean dry cotton cloth as noted in wipe application.

NOTE: Recommended use of the TR-910 SEALER for more porous or rough Mould Surfaces and maximum performance of the TR-920 RELEASE.

SEA POWER MOULD RELEASES GEL-GLOSS NO-STREAK FAUCET BRITE

TR-920 Multi-Pull

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

TR-920 Multi-Pull

TR-102 Regular Mould ReleaseA high production paste release with excellent breakdown for fast, evencoverage. Formulated for fast drying with a pure carnauba base.Extremely easy to apply and wipe off. May be allowed to sit duringbreaks, lunch, etc. before removal. Use sparingly; area being releasedshould appear moist during application.

TR-104 Hi-Temp Mould ReleaseFormulated to work well with heat accelerated applications. Breaks downand applies like TR REGULAR MOULD RELEASE. Again, allow to drybefore removal. Less wax build-up than conventional synthetic or parafinreleases, due to the hard carnauba base.

TR-108 Basic Mould ReleaseExcellent for breaking in new moulds. Produces a deeper wax coating foradded protection. Recommended for vertical surfaces and those areaswhere masking is required.

TR-111 Slurry WaxA softer version (Semi-Paste Slurry) of the TR-110 available in gal., 5 gal.and drum quantities.

Production Information

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

Product Information

TR-210 Self-Stripping Liquid Mould ReleaseA high production liquid mould release formulated to eliminate wax build-up problems in the Cultured Marble and Fiberglass Reinforced PlasticsIndustries. TR-210 produces a lustrous high gloss finish and sure positivereleases. Reduced mould prep time, elimination of wax build-up andextended mould life are ways TR-210 liquid release improves efficiency.Liquid mould release is recommended for use on fully cured, wellconditioned moulds only. Rapid settling of liquid waxes requires shakingwell before and during use.

TR-214 Regular Liquid Mould ReleaseLess volatile than TR-210 SELF STRIPPING LIQUID MOULD RELEASE, TRREGULAR LIQUID MOULD RELEASE is a thin, effective release for non-skid, sandblasted, knurled or grained surfaces. Eliminates plastic build-upor fill in that mars the finished parts.Liquid mould release is recommended for use on fully cured, wellconditioned moulds only. Rapid settling of liquid waxes requires shakingwell before and during use.

TR-212 HOT Liquid release Agent (High Operating Temp)TR-212 is a High-Temp Liquid Release Agent of a nearly frictionless dry lubricantdispersed in a non-flammable solvent medium. This release works equally wellon metal, epoxy and polyester FRP tooling to temperatures of 500F.* Excellent High-Temperature properties.* (NON-SILICONE). Minimal or no transfer when properly applied and

not in excess.* Refer to Product Data Sheet.

TR-220 Liquid Mould ReleaseTR-220 is a liquid external release agent which contains no Silicone orWaxes. It is ready to use with a non-flammable solvent base. Leaves anoily type release film after rapid solvent evaporation. Ideal for textured ordetailed moulds where gloss is not required or parts are to be painted.* High Temperature use. Stable up to 400F.* Refer to Product Data Sheet.

Production Information (cont.)

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

Product Information (cont.)

TR-301 Sealer GlazeA unique blend of glaze and sealers. Best results obtained by machinebuffing. Closes mould pores and seals new or reconditioned moulds withexcellent results. Products the sharpest shine and finish seen on fiberglasstools. Apply two coats in opposite directions on new or resurfaced toolingfor best results.

TR-500 Resin Cleaner Sealer FinishA most needed product. Cleans, seals and leaves a good carnauba highgloss finish. Contains silicone to add to the lasting beauty and customersatisfaction. If it is your policy to compound finished parts before shipping,try using RESIN CLEANER SEALER FINISH instead, but use sparingly. Yourdealers and customers will certainly be better off as a result. Excellent forcultured marble acrylic and fiberglass bath fixtures.

TR-502 Wax Build-up RemoverA special chemical formulation with no abrasives. Used in a good mouldmaintenance program, it will assure high gloss finished moulds. Designedto be used with a machine buffer at the first sign of haze or wax build-up.Will not break the surface seal. Follow with one coat TR-paste wax. Provenlabor savings for mould maintenance and improved production quality.

TR-510 Poly-Sealant PolishLong lasting Polymer polish for Gel-Coated fiberglass finished parts andpainted surfaces. Leave a durable HI-GLOSS water repellent barrier thatprovides excellent weathering protection.

Repels Weathering

Fiberglass orPainted Surface

Poly SealantPolish Barrier

Production Information (cont.)

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

Product Information (cont.)

TR-900 Liquid Semi-Permanent ReleaseTR-900 is a high-temp semi-permanent release coating which dries rapidlyunder atmospheric condition, bonding an ultra thin clear release film to themould surface. Exceptional multiple releases per application for variouspolyester moulding processes and other resin fiberglass fabrication.Note: Refer to Product Data Sheet.* Rapid cure time speeds production cycle.* Wipes to high gloss finish.* Excellent hi-temp properties.* Multiple releases per application.

TR-920 Liquid Semi-Permanent ReleaseTR-920 is a high-temp multiple capability semi-permanent release coatingwhich cures under atmospheric conditions, bonding a durable thin cleanrelease coating to the mould surface. Multiple releases per application forpolyester, epoxy, polyimides, BMC, SMC, and various other advancedresins in fiberglass or graphite composite moulding processes, thermo-plastic Rotational and Rubber moulding.Note: Refer to Product Data Sheet for application.

TR-930 Liquid Semi-Permanent ReleaseTR-930 is a versatile economical semi-permanent release coating whichprovides multiple releases with most thermoset resins, rubber and otherplastic moulding.* High gloss with additional slip action.* Multiple releases per application.* Rapid cure for increased production.

TR-910 Liquid Semi-Permanent SealantTR-910 Sealer is a resilient moisture cure film-forming base coat whichacts to seal the mould surface before application of the TR-900 SERIESsemi-permanent release agents.Note: Refer to Product Data Sheet.* Protects against STYRENE attack and maximizes performance of the

TR-900, 920 & 930 Liquid Semi-Permanent Release agents.* Aids break-in release and seals porosity.

TR-905 Solvent Mould Prep CleanerA proprietary solvent mixture to remove wax, oils and other surfacecontaminates from reinforced polyester tooling and other hard surfacemoulds.Recommended for preparation and cleaning of mould surface prior toapplication of TR-900 series Semi-Permanent RELEASE or the TR-910 SEALER.

Note: Refer to Product Data Sheet.

Production Information (cont.)

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

Product Information (cont.)

PVA MOULD RELEASE AGENT

Description:Plastrene No. 5 is a water/alcohol solution of Polyvinyl Alcohol (PVA) film forming materials. It has been formulated for use asa parting layer, for separation between unsaturated polyester or epoxy based composites and various mould surfaces.

Plastrene No. 5 is available in clear or blue dyed grades, and can be applied by brush, sponge or spray application. Thematerial is water-soluble and is not recommended for use with resins containing or liberating water during cure (eg: Phenolics).

Application:Residues of other PVC films or any silicone containing release agents should be removed from the mould surface beforeapplication. Any solvent wipes should be followed by cleaning with detergent/water solutions, rinsing and then thorough dryingof the mould surface.

Plastrene No. 5 can be applied to the mould surface using brush, wipe or spray techniques, to give typical film thickness of 5-10 microns (0.2-0.4 thou). Approximately 20-30 minutes drying time (depending on humidity) should be allowed beforestarting part fabrication on the PVA film. Pre-heating the mould surface or application of hot air will speed drying time.

Standard Packaging:Plastic containers (22kg net) DV September 1998

TYPICAL PROPERTIES IN LIQUID STATE AT 25C

Plastrene No 5

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

Features Benefits

Low viscosity Excellent sprayability/application characteristics

Rapid film formation Reduced mould cycle times

Water soluble Mould release/film removal able to be assisted by application of water.

Viscosity

Brookfield RVT sp. 1/100 20-35 cP

Non-Volatile Material 7.5-8.5%

Appearance code 60906 Clear blue liquid

Appearance code 60907 Clear colourless liquid

Plastrene No. 5

Plug PreparationsIf the plug has been finished in a gelcoat or similar polyester type product, then the following products may be used.

1. If the plug has 600grit wet & dry scratches or finer, you may start with 3M Marine High Gloss Cutting Compound using a3M5700 White Compounding buff pad.

2. This should then be followed with the 3M Finesse-it Liquid Finishing Compound, using the 3M 5705 Yellow Polishing buffpad.

At this stage the Polyester surface should have a high gloss finish.

a) If the plug has been finished with Urethane Paint, it should be allowed to cure for a minimum of seven days beforeany further work is performed on the paint surface. (May be post cured to save time. Check with the paintmanufacturer for specific details).

b) If the finish achieved from spraying is not good enough to mould from, use a fine grade paper to remove any fineorange peel. This should be followed by buffing with 3M Marine High Gloss Cutting Compound, and then finishedwith 3M Finesse-it Liquid Finishing Compound.

3. Once the desired finish has been achieved, the plug surface should then be washed thoroughly with clean soapy water toremove all polish and dust residue.

4. Wipe the mould over with TR-905 Mould Prep Cleaner. This will remove any traces of solvents from the surface.5. Apply two coats of TR-910 Semi-permanent sealer. Allow at least 15-20 minutes between each application. (As with all

release systems, the longer between coats the better they cure)6. Following the application of the TR-910 sealer, apply three coats of TR-900 Semi-Permanent Release, allowing a minimum

of 5-10 minutes between each coat. (As with all release systems, the longer between coats the better they cure).7. Follow this up with one coat of TR-102 regular paste wax, or TR-108 Basic Non Silicone Paste Wax. (With intricate or

complex shaped plugs, a PVA release agent may be used as insurance against hang-ups. If the customer chooses to usePVA, then TR-108 Basic Paste Wax should be used, as it does not contain silicones.)

8. It is recommended that all such finishes are left for at least 24 hours before proceeding. (except if using PVA. The PVAshould be applied and allowed to dry, just prior to gelcoating to ensure no dust is allowed to settle in the PVA film)

9. The Tooling Gelcoat may now be applied.

Mould PreparationsOnce the mould has been removed from the plug, the decision needs to be made on which release system is to be used. Large mouldstake a long time to laminate. This means that the mould will have gelcoat sitting on it for a day or so, before a tie layer is applied.For this reason, it is not recommended that the semi-permanent systems are used, due to the possibility of Pre-Release in warmerweather.

Hulls & Decks New Moulds (low production runs)It is recommended that new moulds should be left to cure for at least two weeks before any finishing or preparation work iscommenced on them. (Follow cure and hardness specifications, of Gelcoats manufacturer)If the mould finish is as required, follow release procedures below. If the mould requires additional work to achieve an improvedfinish, use the following procedures.1. Buff the mould using 3M Mould and Tooling Compound.2. If required, this may also be followed with 3M Finesse-It Finishing Compound, which will produce a uniform exceptionally

high gloss finish, eliminating swirl marks.3. Thoroughly wash the entire mould with clean water to remove any compound residue and wipe completely dry.4. Clean the entire surface with TR-905 mould prep cleaner and dry off with a second cloth before the cleaner.

Plug & Mould Preparation

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

Plug and Mould Preparation

5. Apply two coats of TR-910 Semi Permanent Sealer. Allow 15-20 minutes cure between coats and 30 minutes after finalcoat. (preferably longer if schedule permits)

6. Apply 4-5 coats of TR paste wax. (if using TR-102 regular, or TR-104 Hi Temp, allow to dry (5-10 minutes) and polish witha soft cloth).

Note: It is recommended allowing an hour or more between coats, to permit solvent evaporation and the carnauba base to set.Allow to stand for at least 24 hours. Then apply additional coat of paste wax and leave for a minimum of one hour priorto commencing initial layup. If temperatures are below 25C, longer cure time should be allowed.

7. With intricate or complex shaped moulds, a PVA release agent may be used on the first couple of parts as insurance againsthang-ups. If the customer chooses to use PVA, then TR-108 Basic paste wax should be used, as it does not contain silicones.

8. Apply 1 coat of TR paste wax between each of the first 4-5 parts to condition the mould. (Then apply as needed. Frequencywill vary depending on mould design and materials used)

9. Once the mould is broken in, you may change over to TR-210 Self-Stripping Liquid Wax. This product is applied by cloth,sponge or by spraying. The mould should appear wet when applied. Allow to dry, and polish off with a clean soft cloth.Using TR-210 will keep the mould free of wax build up and provide a high gloss finish.

Note: Liquid waxes must be shaken regularly during application, due to separation between the solvents and waxes.

Non-Skid Areas10. With all non-skid areas apply TR-214 Regular Liquid Mould Release. This produce is less volatile than the TR-210. It is

slower drying and will penetrate the deep crevices within the patterns. Work into deep areas with a stiff bristled brush.Allow to dry and buff off with a clean soft cloth. (Repeat treatment to these areas with 3-4 coats).

11. Apply one additional coat of TR-214 Regular Liquid Mould Release between the first 4-5 parts.Note: Liquid waxes must be shaken regularly during application, due to separation between the solvents and waxes.12. There after apply as necessary or when parts get tight.

New Moulds (high volume production runs)It is recommended that new moulds should be left to cure for at least two weeks before any finishing or preparation work iscommenced on them.If the mould finish is as required, follow release procedures below. If the mould requires additional work to achieve an improvedfinish, use the procedures mentioned previously.1. Clean the entire surface with TR-905 mould prep cleaner and dry off with a second cloth before the cleaner dries.2. Apply two coats of TR-910 Semi Permanent Sealer. Allow 15-20 minutes cure between coats and 30 minutes after final

coat. (preferably longer if schedule permits)3. Apply 2 coats of TR-900 Semi Permanent Release. Allow 5-10 minutes cure between coats.Note: It is recommended allowing at least 30 minutes before commencing initial layup. As with all release systems, the longer

they are allowed to cure, the better they will perform. (With intricate or complex shaped moulds that require somehorizontal pull or added slip when de-moulding, then TR-920 should be used in place of the TR-900.

Finished PartsDepending on what state the finished parts are, will depend on what compounds should be used on the finish product.Presuming the products have a good finish from the mould, only a final clean and shine will be necessary.1. the most universal product that will provide an excellent result is TR Gel Gloss. The larger trade pack is TR-500. The product

will clean and shine the surface.2. For a higher grade finish, use TR-510 Poly Sealant. This product will put a long lasting Polymer Coating over the entire

surface. It will leave a high gloss and provide an excellent barrier against UV weathering.

Plug & Mould Preparation (cont.)

To the extent permitted by law and subject to any implied warranties under the Trade Practices Act 1974, we make no warranties and representations, express or implied, as to the description,merchantable quality or fitness for purpose of the goods described or the care and skill of any services provided.If any implied statutory provisions apply, to the extent that is permitted by law, our liability will be limited at our option to:(a) in the case of supply of goods: (i) the replacement of the goods or supply of equivalent goods; (ii) the payment of the cost of replacing the goods or acquiring equivalent goods; or(iii) the payment of having the goods repaired or the repair of the goods;(b) in the case of services: (i) the supply of the services again; or (ii) the payment of the cost of having the services performed again.To the extent permitted by law, we will not be liable for any loss, damage, expense, injury or death sustained or incurred by a customer or any other party resulting directly or indirectly out of:(i) the supply, performance or use of any goods or services; (ii) the breach of any agreement between us and a customer; or (iii) our negligence.

Plug & Mould Preparation (cont.)