motor graders — section contents - · pdf filemotor graders — section contents...

2Q2011 10-1

Motor Graders — Section ContentsPage

Tungsten Carbide Cutting Edges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-02Flat Carbide Insert Edges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-02Rotating Bit System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-03Mining Bit System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-03GraderBits™ System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-04Curved Cutting Edges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-04Flat Cutting Edges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-05Utility Edges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-06Curved Serrated Cutting Edges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-06Flat Serrated Cutting Edges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-06Serrated Cutting Edges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-07Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-08Moldboard End Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-08Overlay End Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-09Underbody Truck Plow Edges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-09Moldboard Repair Plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-09High-Carbon Steel Motor Grader Cutting Edges . . . . . . . . . . . . . . . . . . . . . .10-18

Motor Graders

4.75" (121 mm) NARROW TUNGSTEN CARBIDE CUTTING EDGESEdge 2' 3' Overlay Bolt Thickness 607 mm 914 mm End Bit Size*0.75" (19 mm) 217-4695 208-8862 135-9345 0.63" (16 mm)

208-8863 217-4698 135-9369 0.75" (19 mm)Bolt Quantity 5 7* See page 10-7 for part numbers.

6.75" (171 mm) WIDE TUNGSTEN CARBIDE CUTTING EDGESEdge 2' 3' 4' Overlay BoltThickness 607 mm 914 mm 1219 mm End Bit Size*0.75" (19 mm) 195-7265 195-7264 135-9346 0.63" (16 mm)

195-7266 195-7267 135-9370 0.75" (19 mm)217-4699** 208-8866**

Bolt Quantity 5 7 9* See page 10-7 for part numbers.

** Tight Joint. 3/4 bolt holes.

6.88" (173 mm) WIDE TUNGSTEN CARBIDE FLAT CUTTING EDGESEdge 3' 4' BoltThickness 914 mm 1219 mm Size0.75" (19 mm) 195-7260 195-7262 0.63" (16 mm)

6.69" (170 mm) WIDE SERRATED TUNGSTEN CARBIDE CUTTING EDGESEdge 2' 3' Overlay BoltThickness 607 mm 914 mm End Bit Size*1" (25 mm) 208-8864 217-4696 135-9346 0.63" (16 mm)

208-8865 217-4697 135-9370 0.75" (19 mm)Bolt Quantity 5 7* See page 10-7 for part numbers.

FLAT CARBIDE INSERT EDGESPart Flat/ Insert/Front Bolt Hole Bolt Hole Bolt Hole Top Carbide Carbide

Number Curved Tile Thickness Width Length Gauge Line Spacing Size Bevel Type Size198-2635 flat insert 3/4" 5" 3' 1.50" Stand. Hwy Punch 5/8" yes trapezoid 5/8" x 3/8"198-2659 flat insert 3/4" 5" 4' 1.50" Stand. Hwy Punch 5/8" yes trapezoid 5/8" x 3/8"351-8479 flat insert 3/4" 5" 5' 1.50" Stand. Hwy Punch 5/8" yes trapezoid 5/8" x 3/8"283-1063 flat insert 3/4" 5" 4' 1.50" Stand. Hwy Punch 3/4" yes trapezoid 5/8" x 3/8"356-5241 flat insert 7/8" 5" 3' 1.50" Stand. Hwy Punch 5/8" yes trapezoid 5/8" x 3/8"356-5242 flat insert 7/8" 5" 4' 1.50" Stand. Hwy Punch 5/8" yes trapezoid 5/8" x 3/8"356-5243 flat insert 7/8" 5" 5' 1.50" Stand. Hwy Punch 5/8" yes trapezoid 5/8" x 3/8"275-2478 flat insert 3/4" 6" 3' 1.50" Stand. Hwy Punch 5/8" yes trapezoid 5/8" x 3/8"264-2215 flat insert 3/4" 6" 4' 1.50" Stand. Hwy Punch 5/8" yes trapezoid 5/8" x 3/8"330-9491 flat insert 3/4" 6" 3' 1.50" Stand. Hwy Punch 3/4" yes trapezoid 5/8" x 3/8"286-3148 flat insert 3/4" 6" 4' 1.50" Stand. Hwy Punch 3/4" yes trapezoid 5/8" x 3/8"346-6704 flat insert 7/8" 6" 4' 1.50" Stand. Hwy Punch 5/8" yes trapezoid 5/8" x 3/8"346-6329 flat insert 7/8" 8" 3' 1.50" Stand. Hwy Punch 5/8" yes trapezoid 5/8" x 3/8"346-6328 flat insert 7/8" 8" 4' 1.50" Stand. Hwy Punch 5/8" yes trapezoid 5/8" x 3/8"354-8411 flat insert 3/4" 6" 41" 1.50" 2-3/8-12-12-12-2-3/8 5/8" yes trapezoid 5/8" x 3/8"354-8412 flat insert 3/4" 6" 43" 1.50" 9.38-12-12-9.38 5/8" yes trapezoid 5/8" x 3/8"319-7909 flat insert 3/4" 6" 3' 1.50" 2" Hole Spacing 5/8" yes Bull Nose 5/8" x 3/8"310-5270 flat insert 3/4" 6" 4' 1.50" 2" Hole Spacing 5/8" yes Bull Nose 5/8" x 3/8"310-5269 flat insert 3/4" 6" 44" 1.50" 2" Hole Spacing 3/4" yes Bull Nose 5/8" x 3/8"

10-2 2Q2011

Motor Graders

ROTATING BIT SYSTEMPart Number Description Length Bolt Size Shank Size Bits/Board Bit Part Number

308-8574 Adapter Board 3' 5/8" 7/8" 21 348-9051308-8575 Adapter Board 4' 5/8" 7/8" 28 348-9051307-2613 Adapter Board 3' 3/4" 7/8" 21 348-9051307-2615 Adapter Board 4' 3/4" 7/8" 28 348-9051323-1251 Adapter Board 3' 3/4" 1" 21 322-7295321-4272 Adapter Board 4' 3/4" 1" 28 322-7295358-9039 Adapter Board 3' 5/8" 1" 21 322-7295358-9040 Adapter Board 4' 5/8" 1" 28 322-7295

Bit Info:348-9051 = Container of 50 bits each 322-7295 = Container of 30 bits each

MINING BIT SYSTEM (Part I)Moldboard Adapters Required per Moldboard Length Total

Length 3' 4' Boltsfeet mm 914 mm 1219 mm *Needed*10 3048 2 1 1911 3353 1 2 2112 3658 0 3 2313 3962 3 1 2414 4267 2 2 3015 4572 1 3 2816 4877 0 4 3624 7315 8 0 54

* Bolts required per moldboard where holes line up.

MINING BIT SYSTEM (Part II)Narrow Gap Wide Gap

5/8" 3/4" 5/8" 3/4" 5/8" 3/4" 5/8" 3/4"Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt

Adapter 135-9596 135-9592 135-9590 135-9588 135-9593 135-9591 135-9589 135-9587Bolt 3F-5108 5J-4771 3F-5108 5J-4771 3F-5108 5J-4771 3F-5108 5J-4771Nut 4K-0367 2J-3506 4K-0367 2J-3506 4K-0367 2J-3506 4K-0367 2J-3506

Mining Bit*Wide — 2.36" (60 mm) (13) 135-9586 (18) 135-9586 (10) 135-9586 (14) 135-9586Standard — 1.18" (30 mm) (13) 308-5193 (18) 308-5193 (10) 308-5193 (14) 308-5193

* Includes Snap Ring Retainer.

MINING BIT SYSTEM (Part III) (24H)Adapter — 3' (914 mm) 178-4095

Bolt — 1" (25 mm) 1J-3527Nut 2J-3407Washer (13) 5P-8250

Mining Bit — 1.57" (40 mm) 310-2113

4' (1219 mm)3' (914 mm)4' (1219 mm)3' (914 mm)

2Q2011 10-3

Motor Graders

10-4 2Q2011

Motor Graders

GRADERBITS™ SYSTEM* (Part I)Moldboard Adapters Required per Moldboard Length Total

Length 3' 4' Boltsfeet mm 906 mm 1211 mm Needed**10 3048 2 1 1911 3353 1 2 2112 3658 0 3 2313 3962 3 1 2414 4267 2 2 3015 4572 1 3 2816 4877 0 4 36

* See pages 10-12 and 10-13 for further information on GraderBits™ System and gap configuration.** Bolts required per moldboard where holes line up.

GRADERBITS™ SYSTEM (Part II)Narrow Gap Wide Gap

3' (906 mm) 4' (1211 mm) 3' (906 mm) 4' (1211 mm) 5/8" 3/4" 5/8" 3/4" 5/8" 3/4" 5/8" 3/4"Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt

Adapter 159-0311 159-0318 159-0312 159-0317 159-0315 159-0313 159-0316 159-0314Bolt 3F-5108 5J-4771 3F-5108 5J-4771 3F-5108 5J-4771 3F-5108 5J-4771Nut 4K-0367 2J-3506 4K-0367 2J-3506 4K-0367 2J-3506 4K-0367 2J-3506

GraderBit*Wide — 2.36" (60 mm) (15) 6Y-4340 (20) 6Y-4340 (12) 6Y-4340 (16) 6Y-4340Standard — 1.18" (30 mm) (15) 6Y-4339 (20) 6Y-4339 (12) 6Y-4339 (16) 6Y-4339Penetration — 0.91" (23 mm) (15) 105-5180 (20) 105-5180 (12) 105-5180 (16) 105-5180Sharp — 0.61" (15.5 mm) (15) 105-5183 (20) 105-5183 (12) 105-5183 (16) 105-5183

Snap Ring Retainer (15) 353-2624 (20) 353-2624 (12) 353-2624 (16) 353-2624* Includes Snap Ring Retainer.

Snap Ring Pliers 1P-1860

6" (152 mm) CURVED CUTTING EDGES Edge Length

Edge 2' 4' 5' 6' 7' 8' BoltThickness 607 mm 1217 mm 1522 mm 1826 mm 2131 mm 2436 mm Size*

0.50" 3G-8016 9J-3862 8D-2786 8D-2787 8J-7782 0.63" (16 mm)(13 mm) 9J-3660 9J-3659 9J-3656 0.75" (19 mm)

0.63" 9W-1835 7D-4508 5D-9553 5D-9554 8J-4043 0.63" (16 mm)(16 mm) 9J-3657 9J-3658 9J-3655 0.75" (19 mm)

0.75" 3G-7966 5D-9556 5D-9557 0.63" (16 mm)(19 mm) 4Z-8785 0.75" (19 mm)

Bolt Quantity 4 9 11 13 15 17* See page 10-7 for part numbers.

8" (203 mm) CURVED CUTTING EDGESEdge Length

Edge 2' 3' 4' 5' 6' 7' 8' 9' BoltThickness 607 mm 912 mm 1217 mm 1522 mm 1826 mm 2131 mm 2436 mm 2740 mm Size*

0.50" 3G-7965 9J-3863 8D-2788 8D-2789 8J-8980 0.63" (16 mm)(13 mm) 135-6738 134-1779 3G-1626 3G-1627 3G-1628 0.75" (19 mm)

0.63" 109-3137 a 132-1088 7D-4509 5D-9562 5D-9561 5D-9731 0.63" (16 mm)(16 mm) 3G-2166 134-1773 9J-7701 7D-1158 8J-9821 0.75" (19 mm)

0.75" 6G-8623** 132-1087 9W-6252 5D-9558 5D-9559 5D-9732 195-7269 0.63" (16 mm)(19 mm) 3G-2165 109-3124 4Z-8131** b 7D-1576 7D-1577 7D-1949 0.75" (19 mm)

1" 253-0214 4T-2240 4T-2244 4T-2242 4T-2237 0.63" (16 mm)(25 mm) 109-3150 4T-2231 4T-2233 4T-2236 0.75" (19 mm)

Bolt Quantity 4 9 11 13 15 17 19* See page 10-7 for part numbers.

** 12" (304.8 mm) centers on bolt holes.a 109-3137 uses bolt quantity of 5.b 4Z-8131 uses bolt quantity of 7.

8" (203 mm) FLAT CUTTING EDGES Edge Length

Edge 3' 4' 5' 6' 7' 8' BoltThickness 912 mm 1217 mm 1522 mm 1826 mm 2131 mm 2436 mm Size*

0.63" 4T-2967 4T-2968 4T-2969 4T-2966 0.63" (16 mm)(16 mm) 4Z-8120 4T-2971 4T-2970 4T9603 0.75" (19 mm)

0.75" 4Z-8129** 4Z-8119** a 4T-3034 4T-3007 4T-3036 4T-3035 0.63" (16 mm)(19 mm) 4T-3033 4T-3032 4T-3037 0.75" (19 mm)

1" 135-9692 7T-3497 7T-3499 7T-3498 7T-3496 0.63" (16 mm)(25 mm) 4Z-8926 7T-3493 7T-3494 7T-3495 0.75" (19 mm)

Bolt Quantity 5 9 11 13 15 17* See page 10-7 for part numbers.

** 12" (304.8 mm) centers on bolt holes.a 4Z-8119 uses bolt quantity of 6.


Edge 9' 10' 11' 12' BoltThickness 2743 mm 3048 mm 3352 mm 3657 mm Size*

0.63" 135-9366 109-2699 109-2698 132-1011 0.63" (16 mm)(16 mm) 0.75" (19 mm)

0.75" 135-9367 135-9368 140-6828 107-3431 0.63" (16 mm)(19 mm) 0.75" (19 mm)

1" 0.63" (16 mm)(25 mm) 0.75" (19 mm)

Bolt Quantity 11 12 13 14* See page 10-7 for part numbers.


Edge 6' 7' 8' BoltThickness 1826 mm 2131 mm 2436 mm Size*1" (25 mm) 4T6502 4T6508 4T6511 0.75" (19 mm)

1.38" (35 mm) 4T-8316 4T-8317 0.75" (19 mm)1.75" (45 mm) 104-3628 0.75" (19 mm)Bolt Quantity 13 15 17

* See page 10-7 for part numbers.

11" (280 mm) FLAT CUTTING EDGES Edge Length Edge Length

Edge 7' 8' BoltThickness 2131 mm 2436 mm Size

1" (25 mm) 140-6790 140-6832** 0.75" (19 mm)1.38" (35 mm) 132-1086 0.75" (19 mm)

1" (25 mm) 140-6832* 0.75" (19 mm)Bolt Quantity 15 17

* Cutting edge has 12" (304.8 mm) between bolt holes.** Single Bevel.


Edge 8' BoltThickness 2436 mm Size

1.38" (35 mm) 4Z-9188 0.75" (19 mm)Bolt Quantity 17

2Q2011 10-5

Motor Graders

13" (330 mm) FLAT CUTTING EDGES Edge Length Edge Length

Edge 4' 8' BoltThickness 1217 mm 2436 mm Size

1.18" (28.5 mm) 109-3117 1" (25 mm)1.75" (45 mm) 128-2577 0.75" (19 mm)

109-3116 1" (25 mm)2.36" (60 mm) 132-1019 1" (25 mm)Bolt Quantity 9 17


Edge 4' BoltThickness 1217 mm Size

1.18" (28 mm) 135-9690 1" (25 mm)2.38" (60 mm) 135-9349 1" (25 mm)

3" (75 mm) 135-9576 1" (25 mm)1.75" (45 mm) 138-6440 1" (25 mm)Bolt Quantity 9

16" (406 mm) UTILITY EDGESEdge Edge Edge Part Bolt

Thickness Type Length Number Size

2.38" (60 mm) Flat 4' (1217 mm) 178-4106 1' (25 mm)1.75" (45 mm) Flat 4' (1217 mm) 195-7270 1' (25 mm)2.38" (60 mm) Serrated 4' (1217 mm) 208-8870 1' (25 mm)

8" (203 mm) CURVED SERRATED CUTTING EDGES Edge Length

Edge 3' Tooth Size/ 4' Tooth Size/ 5' Tooth Size/ BoltThickness 912 mm Tooth Gap 1217 mm Tooth Gap 1522 mm Tooth Gap Size*

0.75" 8D-3428 36 mm/25 mm 8D-3429 36 mm/25 mm 0.63" (16 mm)(19 mm) 8J-8255 36 mm/25 mm 8J-8256 36 mm/25 mm 0.75" (19 mm)

1"(25 mm) 253-0217 36 mm/25 mm 4T-3512 62 mm/40 mm 4T-3511 62 mm/40 mm 0.75" (19 mm)

Bolt Quantity 7 9 11

Edge Length Edge 6' Tooth Size/ 7' Tooth Size/ 8' Tooth Size/ Bolt

Thickness 1826 mm Tooth Gap 2131 mm Tooth Gap 2436 mm Tooth Gap Size*0.75" 132-1072 36 mm/25 mm 4Z-9020 36 mm/25 mm 132-1073 36 mm/25 mm 0.63" (16 mm)

(19 mm) 350-7200 50.8 mm/26.2 mm 350-7202 50.8 mm/26.2 mm 0.75" (19 mm)1"

(25 mm) 350-7201 60.3 mm/31.8 mm 0.75" (19 mm)Bolt Quantity 13 15 17

* See page 10-7 for part numbers.

8" (203 mm) FLAT SERRATED CUTTING EDGES Edge Length

Edge 4' 5' Tooth Size/ 6' 7' Tooth Size/ BoltThickness 1217 mm 1522 mm Tooth Gap 1822 mm 2127 mm Tooth Gap Size*

0.75" 350-7193 36 mm/25 mm 350-0179 350-0181 50.8 mm/26.2 mm 0.63" (16 mm)(19 mm) 350-0180 50.8 mm/26.2 mm 0.75" (19 mm)

1"(25 mm) 7T-3600 7T-3601 0.75" (19 mm)

Bolt Quantity 9 11 62 mm/40 mm 13 15

* Allows use of cutting edges/hardware with 5/8" bolt holes.

10-6 2Q2011

Motor Graders


Edge 4' 5' Tooth Size/ 7' Tooth Size/ 8' Tooth Size/ BoltThickness 1217 mm 1522 mm Tooth Gap 2127 mm Tooth Gap 2436 mm Tooth Gap Size*

1.0"(25.4 mm) 4T-8800 4T-8801 62 mm/40 mm 4Z-8055 55.9 mm/33 mm 4Z-8056 57.2 mm/33.3 mm 0.75" (19 mm)

1.38" 4Z-8346 55.9 mm/33 mm 100-4581 57.2 mm/33.3 mm 0.75" (19 mm)(35 mm) 350-0182 60.9 mm/60.9 mm

350-0183 77.8 mm/58.7 mm350-0184 102.5 mm/77.1 mm350-0186 107.9 mm LH/63.5 mm350-0185 107.9 mm RH/63.5 mm253-0198 58.5 mm/51 mm

1.75"(45 mm) 104-3631 62 mm/41.3 mm 0.75" (19 mm)

Bolt Quantity 9 11 15 17

* Allows use of cutting edges/hardware with 5/8" bolt holes.


Edge 4' Tooth Size/ 8' Tooth Size/ BoltThickness 1217 mm Tooth Gap 2436 mm Tooth Gap Size*

1.75" (45 mm) 134-1778 90 mm/38.5 mm 0.75" (19 mm)138-6542 61 mm/40.6 mm 1" (25 mm)

2.36" (60 mm) 132-4753 61 mm/40.6 mm 1" (25 mm)Bolt Quantity 9 17

* See below for part numbers.

16" (406 mm) SERRATED CUTTING EDGES Edge Length

Edge 4' Tooth Size/ BoltThickness 1217 mm Tooth Gap Size*

2.38" (60 mm) 135-9796 61 mm/40.6 mm 1" (25 mm)3" (75 mm) 135-9797 61 mm/40.6 mm 1" (25 mm)

Bolt Quantity 9

* See below for part numbers.

2Q2011 10-7

Motor Graders

Reducer Bushings — for moldboards with ¾" bolt holes

2 PN’s/sizes:

280-4070 — 7/8" moldboard thickness

280-4071 — 1" moldboard thickness

• M Series grader moldboards all 3/4" hole size (exception: 24M)

10-8 2Q2011

Motor Graders

HARDWARESize Application Bolt Nut Washer

0.63" (16 mm) All 3F-5108 4K-0367 5P-82470.75" (19 mm) Except 14G, 16G, & H Series 4F-7827 2J-3506 5P-82480.75" (19 mm) 140H, 143H, 160H, 163H, 14G, 14H 5J-4773 2J-3506 5P-82480.75" (19 mm) 16G except 16' blade 5J-4771 2J-3506 5P-82480.75" (19 mm) 16H, 16G with 16' blade (20) 5F-8933 2J-3506 5P-82480.75" (19 mm) (2 bolt part numbers for 16H (22) 5J-4771 2J-3506 5P-8248

and 16G with 16' blade)1" (25 mm) 24H (16) 1J-3527 2J-3507 5P-82501" (25 mm) (2 bolt part numbers for 24H) (54) 4J-9058 2J-3507 5P-8250

Note: The 140H & 143H motor graders use both 0.63" (16 mm) and 0.75" (19 mm) bolts depending on the bladegroup number. See table below for application.

Blade Group No. Bolt Size

8X-8011 0.63" (16 mm)8X-8016 0.63" (16 mm)112-4520 0.75" (19 mm)112-4521 0.75" (19 mm)

MOLDBOARD END BITS

Grader End Bit Moldboard Hardware Model S/N Qty. End Bit Qty. Bolt Nut

16G 93U1-93U2777 9D-4880/1 4 4F-7827 2J-350616G, 16H 93U2778-Up 2 8E-5530 5 1J-6762 a 2J-350616 All others 9J-4407/8 4 3F-5108 4K-036714G 96U1-7324 9J-4405/6 4 4F-7827 2J-350614G 96U7325-Up 2 8E-5529 5 5J-4773 2J-350614 All others 7D-2083/4 5 3F-5108 4K-0367112, 12, All 2 7D-2052* 5 3F-5108 4K-0367120, 130, 9W-2945**140120H, 135H, 12G, 2 8E-5531 5 3F-5108 4K-036712H, 140H, 143Hwith 5/8" holes160H 2 8E-5529 5 5J-4773 2J-3506212 All 2 9J-4411 4 3F-5108 4K-036724H All 2 109-3118 6 1J-3527 2J-3507

NOTE: For machines equipped with power blade arrangement, refer to the appropriate parts book for the correct moldboard end bit.* Use 8E-5531 End Bits on the following machines:

12G (61M11716-UP)120G (87V08135-UP)130G (74V02293-UP)140G (72V09829-UP)

** 9W-2945 is 1/8" (3 mm) thicker than 7D-2052 and is recommended for use when installing overlay end bits. a Use larger 5F-8933 bolt where rear moldboard reinforcing plates are used.

2Q2011 10-9

OVERLAY END BITS Hardware

Overlay Bolt NutEdge in mm Model End Bit Type (5 each) (5 each)

Curved Edge 8 203 12, 120, 130, 140 6D-1948* R 4F-3658 4K-0367early 14 7D-5583 R 1J-6762 2J-3506early 16 7D-5193 R 4F-3658 4K-0367

14G, 16G 7D-9999 R 1J-6762 2J-350614G (96U7325-UP), 6Y-2805 R 1J-6762 2J-3506

14H, 140H, 143H w/ 3/4" holes,160H, 163H

16G (93U2778-UP) 6Y-2805 R 1J-6762 2J-3506Curved Edge 8 203 12H, 120H, 135H, 9W-1768 R 4F-3658 4K-0367

140, 143H w/ 5/8" holesCurved Edge 6 152 12, 120, 130, 140, 6D-1904** R 4F-3658 4K-0367

early 14 & 16early 16 7D-5582 R 1J-6762 2J-3506

Flat Edge1 8 203 12, 120, 130, 140, 4D-5757/8 NR 4F-3658 4K-0367later 14

1 Flat overlays must be used with flat edges. NR — non-reversible* Use 9W1768 overlay end bits on the following machines. R — reversible

** Use 9W1767 overlay end bits on the following machines.12G (61M11716-UP)120G (87V08135-UP)130G (74V02293-UP)140G (72V09829-UP)

UNDERBODY TRUCK PLOW EDGESPlow Hole

Part Number Name Description Edge Size Bolt Type Bolt Spacing Position356-5781 Single Bevel C/E BOCE 3/4" x 6" x 60" 5/8" Curved 6" Wide 3" & 6"-Stand. Hwy Punch Top314-7608 Single Bevel C/E BOCE 3/4" x 6" x 72" 5/8" Curved 6" Wide 3" & 6"-Stand. Hwy Punch Top317-0995 Single Bevel C/E BOCE 3/4" x 6" x 84" 5/8" Curved 6" Wide 3" & 6"-Stand. Hwy Punch Top317-0996 Single Bevel C/E BOCE 3/4" x 6" x 96" 5/8" Curved 6" Wide 3" & 6"-Stand. Hwy Punch Top352-0648 Single Bevel C/E BOCE 3/4" x 8" x 60" 5/8" Curved 8" Wide 3" & 6"-Stand. Hwy Punch Top314-7609 Single Bevel C/E BOCE 3/4" x 8" x 72" 5/8" Curved 8" Wide 3" & 6"-Stand. Hwy Punch Top333-2818 Single Bevel C/E BOCE 3/4" x 8" x 84" 5/8" Curved 8" Wide 3" & 6"-Stand. Hwy Punch Top317-0997 Single Bevel C/E BOCE 3/4" x 8" x 96" 5/8" Curved 8" Wide 3" & 6"-Stand. Hwy Punch Top

BOCE — Bolt-On Cutting Edge.

MOLDBOARD REPAIR PLATES***

Moldboard Length Dimensions feet mm W-H-T (inch) W-H-T (mm) Part

13-14 3962-4267 75 x 15.25 x 0.38 1905 x 387 x 10 4D-5821*12-13 3658-3962 63 x 15.25 x 0.38 1600 x 387 x 10 4D-5820**

* Use 8W-5266 for larger radius moldboards. Radius is 16.25" (413 mm).** Use 8W-5265 for larger radius moldboards. Radius is 16.25" (413 mm).

*** Blank Plate without Bolt Holes.

Motor Graders

10-10 2Q2011

Motor Graders

CAT GRADER EDGES . . .

Job-matched for Most Efficient Blade PerformanceCaterpillar offers three types of grader edges — curved, flat and serrated.The standard curved type is offered in two widths, four thicknesses and sixlengths to fit every possible job condition and moldboard. The standard flattype is offered in two widths, four thicknesses and four lengths. All Catgrader edges are made of tough, thru-hardened DH-2™ steel for strength andwear resistance. They are unconditionally guaranteed against breakage.

CAT MOTOR GRADER CUTTING EDGE APPLICATION GUIDE

For Most ApplicationsRecommend curved or flat 0.63" (16 mm) or 0.75" (19 mm) thick edges. Thethicker, 1" (25 mm) edges should be used when abrasive wear is a greaterproblem than penetration; the thinner edges when penetration is critical.

Recommend 8" (203 mm) wide edges for more wear material and feweredge changes.

For Finish GradingRecommend 0.50" (13 mm) thick curved edges. They provide good pene -tra tion and stay sharp longer. There is less throw-away iron than withthicker edges.

For Severe ApplicationsRecommend 1.38" (35 mm) thick by 10" (254 mm) or 1" (25 mm) thickby 10" (254 mm) wide flat edges. They provide maximum strength andwear material. In severe applications these edges will provide the lowestmaterial costs per hour.

For Maximum PenetrationRecommend 0.75" (19 mm) thick serrated edges. Serrated edges exert moredown pressure per square inch of contact area for improved penetration infrozen or hard-packed materials. In heavy-duty applications, 1" (25 mm) by10" (254 mm) flat or 1" (25 mm) by 8" (203 mm) flat or curved serratededges may be used. In extreme conditions, serrated edges can be installedover standard 6" (152 mm) edges for extra strength.

For High Abrasion/Low Impact ApplicationsCaterpillar offers two different types of carbide edges. They are the tungstencarbide tile edges and the tungsten carbide insert edges. Both provide manytimes the wear life and lower cost per hour than standard DH-2 edges if usedas recommended, in low to medium impact, highly abrasive applicationssuch as maintenance of unpaved, sand and gravel roads.The tungsten carbide tile edges are manufactured by milling a flat on the frontof a steel cutting edge base and brazing tungsten carbide “tiles” onto the flat.They are curved for excellent penetration and are available in 2' (610 mm)and 3' (914 mm) lengths and 4.75" (121 mm) and 6.75" (171 mm) widths.The tungsten carbide insert edges are manufactured by milling a slot in thebottom of a steel cutting edge and brazing a tungsten carbide “insert” into theslot. The tungsten carbide insert edges have the carbide sandwiched in agroove between the front and rear surfaces of the edge to protect them fromimpact and therefore lend themselves to higher impact applications likesnow removal.In both types of edges, the life is extended substantially due to the wear char-acteristics of the tungsten carbide.Warranty on the carbide edges is the same as that for GraderBits, meaning thesteel edge base is covered, but not the tungsten carbide tile or insert itself.

Curved

Curved

Flat

Serrated

Tungsten carbide edge

Serrated tungsten carbide edge

Tungsten carbide insert edge

Steel CuttingEdge Base

Tungsten Carbide“Tile”

2Q2011 10-11

Motor Graders

Edge WidthOn motor grader cutting edges, width translates to wear material, so as a general rule,for the longest life, use the widest edge. An 8" (203 mm) edge, for example, will giveyou 100% more available wear material and edge life than a 6" (152 mm) edge… atonly about 35% more cost. In addition, hardware usage and total downtime will be cutby 50%. To extend cost savings even farther, a 10" (254 mm) cutting edge will lastthree times longer than a 6" (152 mm) edge when used under comparable conditions.Crowning describes a normal wear pattern in which the cutting edge conforms to thematerial being graded. When extreme crowning occurs or when finishing applicationsrequire tolerances less than 1/4" (6 mm), the best value may be in selecting anarrower and thinner cutting edge. This approach reduces costs by minimizing theamount of usable iron that must be thrown away.

Edge ThicknessPenetration requirements determine how thick your edge should be. The easier mate-rial is to penetrate, the thicker the edge you should use. This simple chart illustrateshow wear material increases with thickness.

Cat Cutting Edge ThicknessThickness 1/2" 5/8" 3/4" 1" 1-3/4"

(13 mm) (16 mm) (19 mm) (25 mm) (35 mm)Wear MaterialIncrease — 25% 50% 100% 250%

Cat Cutting Edge SizesThickness 6" (152 mm) 8" (203 mm) 10" (254 mm) 11" (280 mm) 13" (330 mm) 16" (406 mm)1/2" (13 mm) Curved Curved — — — —5/8" (16 mm) Curved Curved/Flat — — — —3/4" (19 mm) Curved Curved/Flat/Ser — — — —1" (25 mm) — Curved/Flat/Ser Flat/Ser Flat — —1-3/8" (25 mm) — — Flat Flat — —1-3/4" (45 mm) — — Flat — Flat/Ser Flat1-3/16" (28.5 mm) — — — — Flat Flat2-3/8" (60 mm) — — — — Flat/Ser Flat/Ser3" (75 mm) — — — — — Flat/Ser

10-12 2Q2011

GRADER END BITS

Cat moldboard and overlay end bits are made from tough, thru-hardenedDH-2 steel. Moldboard end bits protect the moldboard itself from wearand damage. Overlays provide additional wear protection and strength forboth the moldboard and the cutting edge.

Moldboard End Bits• Protects end of moldboard from wear and damage.• Recommended for all applications.

Reversible Overlays• Used with curved edges.• Protects and strengthens both moldboard and cutting edges.• Reversible design provides “second life” for greater value.

Flat Overlays• Provides same moldboard and edge protection for flat edges. Not avail -

able for 14G or 16G graders.

Motor Graders

2Q2011 10-13

Motor Graders

CAT GRADERBITS™ SYSTEM

The Cat GraderBits™ System is a motor grader ground engaging tool systemthat can offer your customers many advantages over standard cutting edges.

This system is made up of adapters that bolt up to the moldboard and indi-vidual bits that fit into the adapter.

The Cat GraderBits System has been designed primarily for maintaining andreconditioning gravel roads; including ice and snow removal. In addition, acontinuous Cat GraderBits configuration can be used on paved surfaces.

There are two major customer groups that should be targeted — mines andgovernmental bodies. Since aggregate size is often different on governmental vs.mining haul roads, each group has an adapter designed for its needs. The miningadapter has a wide gap between the Cat GraderBits to accommodate largeaggregate. Since many country roads use smaller aggregates, the gap is narroweron these adapters. Either adapter can be sold in either market providing bolt holediameters match-up. See part number information.

Features/Benefits

The Cat GraderBits System has many benefits. One of the most important is theincrease in wear life over standard, heat-treated edges. However, the Cat GraderBitsSystem costs much more than a set of standard edges. Successful selling willrequire a customer’s understanding of ALL benefits. Selling wear life as the onlyfeature will result in fewer sales.

Features Benefits✔ Serrated design ✔ Excellent penetration, conserves gravel and

increases productivity✔ Tungsten carbide wear material ✔ 6-10 times greater wear life than standard

cutting edge (10" x 1"; 254 mm x 25 mm)✔ 12-15 times greater wear life than standard cutting

edge (8" x 3/4"; 203 mm x 19 mm)✔ Large decrease in grade blade maintenance ✔ Reduced downtime✔ Smoother haulroads ✔ Longer tire and mechanical life, faster travel

speeds✔ Four Cat GraderBit widths ✔ Allows several edge configurations, including

continuous edge

Detailed Comments on Features & Benefits1. One of the benefits that can be seen immediately is the ease of penetration

compared to standard continuous edges. Using a serrated configuration,initial penetration is easier. Ridges are removed and trenches are filled in onepass. Material is allowed to pass between the Cat GraderBits which helpsconserve gravel. All of these benefits help cut costs which will maximizeprofitability.

2. Tungsten Carbide is used on the Cat GraderBits at the wear area. This is thesame material used in Cat abrasion-resistant material edges. It is an extremelyhard alloy which offers excellent wear life in ground engaging tools. CatGraderBit wear life will depend on the application. In a mining haulroadapplication, wear life should range between 6-8 times greater than heat-treated edges. On county roads, it should average 8-10 times the life. A minewill typically have larger aggregate and higher impact than a county road,thus wear life is less than a county road application.

10-14 2Q2011

3. Because of the increased wear life, blade maintenance is reduced whichhelps cut costs. Other systems which have rotating bits require main -tenance for proper operation. The Cat GraderBit System is relativelymaintenance free.

4. Proper use of this system will result in smoother haulroads. Smootherroads promote safer travel and are easier on machines and tires whichcuts repair costs. Faster travel speeds are attainable on smoother roads,which can impact cycle times for off-highway trucks and other machines.

5. Four Cat GraderBits are offered — wide, standard, penetration and sharp— ranging in tip width from 2.36" (60 mm) to 0.61" (15.5 mm). Thisallows several different edge configurations. Using the narrow gapadapter, a continuous edge can be made by using all wide bits. (This isthe only configuration recommended for asphalt applications.) Byalternating wide with any of the other bits, the gap is reduced which maybe better suited for small aggregate. Using the sharp tip alone will givethe maximum gap. The same options can be used for the wider adapter,but a continuous edge is not possible because of the wider gap betweenadapter holes.

6. Regardless of the GraderBits used, it is recommended to place wideGraderBits in the outermost slots. This helps reduce adapter wear onthese end positions.

Installation

The Cat GraderBit System installs easily without moldboard modifi cation.Adapters bolt up to the moldboard like standard edges and the CatGraderBits fit into the adapter holes and are held on with a snap ring. Asnap ring pliers is the only tool necessary for installation. The tungstencarbide portion of the Cat GraderBit should point towards the front of themachine. The system can be installed on any 12, 14 or 16 foot moldboardand can be done in less than 1.5 hours. Individual bits can be removed/installed in less than one minute.

Operation

Proper operation is very important to assure acceptable Cat GraderBit systemlife. There are five points to stress with the operators.

1. The face of the carbide tile should be perpendicular to the ground.2. Moldboard sidecast angle should be between 0-10°. 3. Penetration depth should be approximately 1-1.5" (25-38 mm) maximum.4. Operating speed should be held to 4-6 mph. In higher impact applications,

slower speeds will reduce potential for breakage.5. If machine is equipped with an accumulator, make sure it’s on when

operating GraderBit System.

Motor Graders

Examples of Configurations

2Q2011 10-15

Motor Graders

ESTIMATED GRADERBIT WEAR LIFEAverage

DH-2 Edge GraderBit GraderBitSize Life Range Life

1" x 10" 6–10 81" x 8" 10–14 12

3/4" x 8" 14–18 165/8" x 8" 15 –20 18

WarrantyThe adapter, and Cat GraderBit (with the exception of the tungsten car -bide) are warranted against breakage under the GET warranty. Thetungsten carbide and the braze material are warranted under the standard6-month new parts warranty.

ROTATING BIT SYSTEM

Description

The Cat standard rotating bit system is comprised of three or four footlong adapter boards to accommodate a 7/8" (shank) carbide-tipped bit. Theadapter boards are available in either 5/8" or 3/4" bolt hole punch. There isa heavy-duty adapter board option that accepts a 1" (shank) carbide-tippedbit. The heavy-duty boards are only available in a 3/4" bolt hole punch,and are available in a three and four foot adapter board sections. All three-foot boards use 21 bits; the four-foot boards use 28 bits.

The replaceable carbide bits rotate and self sharpen which allows for superiorwear over conventional curved or flat carbide-insert blades. The carbidetip is also engineered with flat sides that aid in bit rotation. The rotating bitalso provides improved penetration and cutting ability, which can reduce thenumber of passes required by the motor grader compared to conventionalcutting edges. The carbide bits if maintained can last as long as 5–10 setsof conventional grader blades.

The multiple uses of the rotating bit system include; reclaiming lost gravelcast to the shoulders or imbedded into the road surface, which reduces thecost of new material (gravel). The system is extremely useful in cuttingcompacted snow or ice, giving the road better traction than the smoothcutting conventional blade setup. Removing washboards or cutting potholesis another feature of this system, which substantially improves and sustainsthe condition of dirt or oiled roads.

Installation1. Remove existing cutting edges from moldboard. Clean moldboard of

all dirt.2. Bolt Cat adapter boards. Tighten bolts. Rap the bolt heads sharply with

a hammer. Torque bolts a second time.3. On level ground surface, set adapter boards perpendicular, or 90 degrees

from the level ground surface. Set magnetic protractor (ex. Mayes Level +Angle Finder) on front of adapter board surface. Rack moldboard backuntil protractor reads 70 degrees, or adapter board should be racked back20 degrees from perpendicular position.

4. Caution: If adapter angle is not set correctly, the moldboard will chatterand vibrate, and the rotating bits will not properly wear or rotate (flatten).If this occurs, readjust adapter boards to the correct operating angle.(See illustration)

Correctoperating angle

10-16 2Q2011

Motor Graders

Operation1. Insure that bits are rotating freely and the adapter boards are set in correct

operating position.2. Check rotation of bits daily. A bit not rotating will develop a flat wearing

surface on the carbide tip, and leave a channel mark on the road.3. In ice and compacted snow conditions, operate blade in “float” position

with no down pressure. Grade in low gear (3rd or less).4. If bits are not freely rotating, spray or power wash, or remove and clean

debris from bit holder bore hole. Only lubricate with WD 40 or anenvironmentally approved lubricant.

Governmental Bid Specifications for Motor Grader Edges/BitsMany governmental units periodically review their bid specifications forpurchasing motor grader cutting edges and end bits. It is important to beaware of when such reviews take place and provide recommendations.Caterpillar suggests that physical properties, rather than chemical properties,represent the most accurate guide to edge performance.

Where chemical properties are still included in governmental bid specifica tions,you will want to urge the purchasing authorities to review those specificationsagainst the following physical properties and related performance benefits.

1. Through-hardened to a minimum of Rc43 (BR 400)*Through-hardening insures a uniform wear rate and these user benefits:

• Fewer edges to buy.• Reduced downtime for removal and installation.• Less hardware expense.• Lower total labor expense.

* Serrated edges thru-hardened to minimum Rc38 (Br353).

2. Standard bolt hole sizes and spacing0.63" (16 mm) and 0.75" (19 mm) holes for No. 3 head cutting edge bolts.Standard “Highway” punching with either 6" (152 mm) or 12" (305 mm)spacing. This specification standardized both edge and hardware inventories,reducing the number of different parts required in stock.

3. Breakage guaranteeSupplier warrants that if an edge breaks during operation, it will bereplaced free of charge (with the exception of high-carbon edges). Theguarantee translates into positive benefits:

• Fewer edges purchased.• Users save money. Since the guarantee reduces the user’s risk, he can

use 8" (203 mm) wide edges instead of 6" (152 mm) wide edges in mostapplications. This means two extra inches of wear material are available.Cat Motor Grader edges meet all of these requirements.

2Q2011 10-17

Motor Graders

TORQUE REQUIREMENTS FOR PLOW BOLTS Standard Measurements Metric Measurements Size Torque Size Torque

5/8" (0.63") 200 ± 30 ft. lb. 16 mm 270 ± 40 N•m3/4" (0.75") 350 ± 45 ft. lb. 19 mm 475 ± 60 N•m7/8" (0.88") 550 ± 65 ft. lb. 22 mm 750 ± 90 N•m1" (1.00") 850 ± 110 ft. lb. 25 mm 1150 ± 150 N•m

1-1/4" (1.25") 1700 ± 220 ft. lb. 32 mm 2300 ± 300 N•m

NOTE: DO NOT APPLY LUBRICANT OF ANY TYPE TO GET HARDWARE(nut may back off prematurely).1. Clean all surfaces of rust, paint, nicks, and burrs.2. Tighten nuts to listed torque spec.3. Carefully strike plow bolt head with a hammer.4. Re-tighten nuts to listed torque spec.SAFETY GLASSES MUST BE WORN WHEN STRIKING BOLT HEADS.

Torque Specifications Decal PEEP3075

CUSTOMER SERVICE TIPS:

• Remember to recommend moldboard end bits, overlays, and appro pri atequantities of hardware.

• For scarifier shanks and tips, consult the RIPPERS/SCARIFIERS Section.• Moldboard end bits should be recommended for all applications. Over lays

should be recommended for high impact applications.• Reversible overlays should be inspected regularly and inter-changed

(end-to-end) before outside corners wear through.• Users who routinely burn off end bit and edge hardware may realize

substantial savings with a 5P-2410 Hand Impact Wrench which makesfield installation and removal of hardware easy.

InchStandard High LowTorque Torque Torque

1E-0279A 1E-0279G 1E-0279EDiameter (N·m) (N·m) (N·m)

1/4 12 ± 3 13 ± 3 6 ± 15/16 25 ± 6 28 ± 7 13 ± 33/8 47 ± 9 50 ± 10 25 ± 67/16 70 ± 15 80 ± 15 40 ± 81/2 105 ± 20 120 ± 20 60 ± 129/16 160 ± 30 175 ± 30 85 ± 155/8 215 ± 40 240 ± 40 115 ± 203/4 370 ± 50 430 ± 60 200 ± 407/8 620 ± 80 700 ± 90 325 ± 401 900 ± 100 1050 ± 150 500 ± 65

1-1/8 1300 ± 150 1450 ± 150 700 ± 901-1/4 1800 ± 200 2100 ± 250 1000 ± 1251-3/8 2400 ± 300 2700 ± 300 1300 ± 1501-1/2 3100 ± 350 3600 ± 400 1700 ± 200

MetricStandard High LowTorque Torque Torque

1E-0279A 1E-0279G 1E-0279EDiameter (N·m) (N·m) (N·m)

M6 12 ± 3 13 ± 3 6 ± 1M8 28 ± 7 30 ± 7 15 ± 3M10 55 ± 10 60 ± 12 30 ± 7M12 100 ± 20 105 ± 20 50 ± 10M14 160 ± 30 175 ± 30 80 ± 15M16 240 ± 40 270 ± 40 125 ± 20M20 460 ± 60 530 ± 70 250 ± 40M24 800 ± 100 900 ± 100 425 ± 50M30 1600 ± 200 1800 ± 200 850 ± 100M36 2700 ± 300 3100 ± 350 1500 ± 200

1E-0279 Tightening. 1E-0279 provides fastener dynamic assemblytightening requirements for both inch and metric threaded fasteners,tube fittings, plugs, pipe threads, hose clamps and control rodassemblies that do not have a special tightening requirement on thedrawing.

1 N·m = 0.737 lb·ft = 8.85 lb·in

TORQUE REQUIREMENTS FOR STANDARD 1E-0279A BOLTS

10-18 2Q2011

Motor Graders

HIGH-CARBON STEEL MOTOR GRADER CUTTING EDGES

For Governmental Use in Low Impact and Finish Grading Applications

Benefits

✔ Curved double bevel design for excellent penetration

✔ Standard highway bolt hole pattern — fits all makes ofmotor graders

✔ Countersunk bolt holes to protect bolt heads

✔ Rust preventive coating for long, rust-free storage

✔ Backed by Caterpillar Parts Warranty covering defects inmaterial and workmanship

*Subject to certain terms and conditions. See your Caterpillar Dealer for warranty statement.

Cat High-Carbon Steel Motor Grader Edges Meet or ExceedMost State and Local Government High-Carbon Bid Specifications

Material Specification: SAE 1084 High Carbon Steel

Dimensional Specifications: Width Thickness6" (152 mm) 3/4" (19 mm)8" (203 mm) 5/8" (16 mm)W T

1/2" (13 mm)

Profile: Curved Double Bevel

Manufacturing Specifications: Bolt Hole Dimensions: 5/8" (16 mm) or 3/4" (19 mm)Bolt Hole Pattern: Standard Highway Bolt Hole Punch

For additional strength and wear resistance specify Caterpillar Through-Hardened DH-2 Edges

Caterpillar Curved High-Carbon Steel Cutting Edge SizesLength

4' 5' 6' 7' 8' 10' 11' 12' 14'(1219 (1524 (1828 (2133 (2438 (3048 (3353 (3658 (4267

Thickness Width Bolt Hole mm) mm) mm) mm) mm) mm) mm) mm) mm)

1/2" (13 mm) 6" (152 mm)5/8" (16 mm) X X X X X X X X

3/4" (19 mm) X X X X X X X X

5/8" (16 mm) 6" (152 mm)5/8" (16 mm) X X X X X X

3/4" (19 mm) X X X X X

1/2" (13 mm) 8" (203 mm)5/8" (16 mm) X X X X X X X X

3/4" (19 mm) X X X X X X X X

5/8" (16 mm) 8" (203 mm)5/8" (16 mm) X X X X X

3/4" (19 mm) X X X X X

3/4" (19 mm) 8" (203 mm)5/8" (16 mm) X X X X X

3/4" (19 mm) X X X X X

2Q2011 10-19

Motor Graders

10-20 2Q2011

Motor Graders

CURVED MOTOR GRADER EDGES — HIGH-CARBON & DH-2 STEEL

1/2" x 6" (13 mm x 152 mm) CURVED(1E-2693 SECTION HIGH-CARBON & 1E-2394 SECTION — DH2)

Edge 5/8" (16 mm) Bolts Edge P/N 3/4" (19 mm) Bolts Edge P/NLength High-Carbon DH-2 High-Carbon DH-2

14' (1219 mm) 9W-2293 3G-8016 9W-229415' (1524 mm) 9W-2295 9J-3862 9W-229616' (1828 mm) 9W-2297 8D-2786 9W-2298 9J-336017' (2133 mm) 9W-2299 8D-2787 9W-2300 9J-365918' (2438 mm) 9W-2301 8J-7782 9W-2302 9J-365619' (2743 mm) 4Z-896810' (3048 mm) 9W-2303 9W-230412' (3658 mm) 9W-2305 9W-230614' (4267 mm) 9W-2307 9W-2308



14' (1219 mm) 9W-2309 3G-7965 9W-2310 135-673815' (1524 mm) 9W-2311 9J-3863 9W-2312 134-177916' (1828 mm) 9W-2313 8D-2788 9W-2314 3G-162617' (2133 mm) 9W-2315 8D-2789 9W-2316 3G-162718' (2438 mm) 9W-2317 8J-8980 9W-2318 3G-162810' (3048 mm) 9W-2319 9W-232012' (3658 mm) 9W-2321 9W-232214' (4267 mm) 9W-2323 9W-2324



14' (1219 mm) 9W-2325 9W-232615' (1524 mm) 7T-1640 7D-4508 9W-232716' (1828 mm) 7T-1633 5D-9553 7T-1637 9J-365717' (2133 mm) 7T-1645 5D-9554 7T-1626 9J-365818' (2438 mm) 7T-1632 8J-4043 7T-1629 9J-365511' (3353 mm) *4Z-8652*12' (3658 mm) *4Z-8653*

* 6" (13 mm) hole spacing.

CURVED MOTOR GRADER EDGES — HIGH-CARBON & DH-2 STEEL — Continued



2' (610 mm) 109-3137 3G-21664' (1219 mm) 9W-2328 132-1088 9W-2329 134-17735' (1524 mm) 7T-1641 7D-4509 9W-23306' (1828 mm) 7T-1636 5D-9562 7T-1639 9J-77017' (2133 mm) 7T-1643 5D-9561 7T-1624 7D-11588' (2438 mm) 7T-1631 5D-9731 7T-1628 8J-9821



2' (610 mm) 6G-8623 3G-21654' (1219 mm) 9W-2338 132-1087 9W-2339 109-31245' (1524 mm) 9W-2340 9W-6252 9W-2341 **4Z-8131*6' (1828 mm) 7T-1634 5D-9558 7T-1638 7D-15767' (2133 mm) 7T-1623 5D-9559 7T-1625 7D15778' (2438 mm) 7T-1630 5D-9732 7T-1627 7D19494' (3353 mm) 8D-3428 Serrated 8J-8255 Serrated5' (3658 mm) 8D-3429 Serrated 8J-8256 Serrated

* 12" (26 mm) hole spacing.

2Q2011 10-21

Motor Graders

NOTES

10-22 2Q2011 PECJ0025-03

Motor Graders

motor graders — section contents - · pdf filemotor graders — section contents...

Documents