montageanleitung - herbert burda · pdf fileting on burda carcass set. consists of: electronic...
TRANSCRIPT
Montageanleitungelektrische Urinal-Steuerung BurdaTronic U-01 / U-02
Berührungslose Infrarot-Einzelurinalsteuerung. Bedarfs-abhängige Vorspülung, einstellbare Hauptspülung sowie Hygienespülung bei 24 Stunden Nichtbenutzung. Zur Fertigmontage passend auf Burda Rohbauset.
Bestehend aus:Elektronikplatte mit integriertem Netzteil, Montage-rahmen und Magnetventil.Die Montage und Installation darf nur durch einen
konzessionierten Fachbetrieb, gemäß DIN 1988 sowie VDE 0100 Teil 701 erfolgen.Die Netzzuleitung ist über einen 2-poligen Hauptschalter mit mindestens 3 mm Kontaktöffnung zu führen und mit maximal 6A abzusichern! Bei der Planung und Er-richtung von Sanitäranlagen sind die entsprechenden örtlichen, nationalen und internationalen Normen und Vorschriften zu beachten!
Installationshinweise
Betriebsspannung: 230V / 50HzLeistungsaufnahme: ca. 2 VAMagnetventil: 24V / 50HzAktivbereich: 50 cm vorjustiert 30 - 70 cm einstellbarVorspülung: 1 sec. bedarfsabhängigHauptspülung: 1 - 10 sec.Fließdruck: 0,5 - 6 bar
Durchfluss: 0,3 - 0,7 l/sec. nach EN 12541 reduzierbarWasserzulauf: R 1/2“ IGWasserablauf: R 1/2“ AG
Abmessungen:Frontplatte: 160 x 185 mmWandeinbaukasten: 135 x 165 x 77 mm
Technische Daten
2
Einbaumaße in cm
~11
5
min. 100
~50
DN 15
65
Montage
Vorspülung durchführen
3
Vorabsperrung schließenSchmutzfilter einsetzen
Auf
Zu
Magnetventil mit Dichtungen einsetzenAchtung! Flussrichtung bei MV beachten
Vorabsperrung öffnenMontagerahmen anbringen
MV
230V
Netzzuleitung abschalten, Magnetventilanschließen, Netzanschluss herstellenBlockklemme in die vorgesehene Halterungstecken, Netzzuleitung wieder einschalten.
Montage
4
1
5
10
Spülmenge in l Fließdruck 2,0 3,0 4,0
1 bar 5,5 s 7,0 s 10,0 s2 bar 4,5 s 5,5 s 7,5 s3 bar 3,0 s 4,5 s 6,0 s4 bar 2,5 s 4,0 s 5,5 s5 bar 2,5 s 4,0 s 5,0 s
Spülzeit einstellen 1 - 10 sec.
Diagnose LED, leuchtet bei Reflex1
Elektronikplatte in Montagerahmeneinhängen und verschrauben.
Service und Störungsbehebung
59
Wasser fließt ständig
MV-Stecker abziehen
Wasser fließt weiter Elektronikplattetauschen
Spülung funktioniert noch immer nicht
MV falsch eingebaut (Flussrichtung beachten)Mindestwasserdruck 0,3 bar beachten
JA
NEIN
Wasser fließt nicht
Elektronik abnehmen, Wasserzulauf, Vorabsperrung und Schmutzfilter prüfen
LED leuchtet nicht LED leuchtet
Elektronik tauschen
Spülung tritt ein, LED blinkt während der Spülung
Verweilzeit von 4 sec. beachten
Reflex beenden und Spülung kontrollieren
Reichweite - Aktivbereichmit Reflektor (Papier, etc.)
auf ca. 50 bis 60 cm justierenggf. Elektronik tauschen
Dabei Hand oder anderenReflektor (Papier, etc.)
Elektronik mittels Diagnose LEDauf Funktion prüfen
Netzspannung prüfen
Spülung tritt nicht ein
Elektronik tauschen
Magnetventil tauschen
MV tauschen
Ersatzteile
6
503 846 Absperrventil
998 608 Magnetventil 24V
BurdaTronic U-01 ElektronikplatteEdelstahl, 230 V Netzanschluss
BurdaTronic U-02 ElektronikplatteEdelstahl, 9 V Batteriebetrieb
Funktion
7
Mindestverweilzeit 4 sec. Bedarfsabhängige Vorspülung 1 sec. wenn letzte Spülung länger als 5 min. zurückliegt
Einstellbare Hauptspülung von 1 bis 10 sec.
Hygienespülung bei 24 Stunden Nichtbenutzung
503 846 Absperrventil
998 608 Magnetventil 24V
BurdaTronic U-01 ElektronikplatteEdelstahl, 230 V Netzanschluss
BurdaTronic U-02 ElektronikplatteEdelstahl, 9 V Batteriebetrieb
Herbert Burda GmbHKrefelder Straße 8740549 Düsseldorf
Tel. 0211 950 01- 0Fax 0211 50 05 75
www.burda-online.com
Installation GuideNo-touch infrared single urinal control BurdaTronic U-01 / U-02
No-touch infrared single urinal control. Pre-flushing as required, adjustable main flushing cycle, and hygiene flushing when not used for 24 hours. Suitable for moun-ting on Burda carcass set.
Consists of:Electronic board assembly with integrated power supply,mounting frame, and magnetic valve.Mounting and installation must be performed by
licensed craftsmen to DIN 1988 and VDE 0100 part 701 standards only.The mains supply lead is to be led via a 2-pole mains switch with at least a 3mm contact gap and to be protected with 6A maximum!When planning and installing sanitary systems, the relevant local, national, and international standards and regulations must be complied with!
Notes on Installation
Operating voltage: 230V / 50HzPower input: approx. 2 VAMagnetic valve: 24V / 50HzActive range: approx. 50cm preset 30-70 cm adjustablePre-flushing: 1 sec, as requiredMain flushing: 1 - 10 secsFlow pressure: 0,5 - 6 bar
Flow rate: 0.3 - 0.7 l/sec can be red. acc. to EN 12541Water inlet: R 1/2“ IGWater outlet: R 1/2“ AG
Dimensions:Front panel: 160 x 185 mmWall-recess-mounted box: 135 x 165 x 77 mm
Technical Specifications
2
Mounting dimensionsin cm
~11
5
min. 100
~50
DN 15
65
Installation
Carry out pre-flushing
3
Advance shut-off, closeInsert dirt filter
OPEN
CLOSE
Insert magnetic valve with gaskets Caution! Watch out for flow direction at MV
Advance shut-off, openAttach mounting frame
MV
230V
Connect magnetic valve Establish connection to mains Insert terminal block into the provided holder
Installation
4
1
5
10
Flush volume in liters Pressure 2,0 3,0 4,0
1 bar 5,5 s 7,0 s 10,0 s2 bar 4,5 s 5,5 s 7,5 s3 bar 3,0 s 4,5 s 6,0 s4 bar 2,5 s 4,0 s 5,5 s5 bar 2,5 s 4,0 s 5,0 s
Adjust flushing time 1 - 10 secs.Diagnosis LED will be lit if there is a reflex
1
Suspend electronic board on moun-ting frame, and fasten it with screw
Service and Troubleshooting
59
water is not running
remove electronics, check water inlet,inlet shut-off mechanism, and dirt filter
while doing this, hold your hand oranother reflector (paper, etc.) approx.20cm in front of the device
LED is not litcheck function of electronics
with diagnosis LED LED is lit
check mains voltage
replace electronics
observe waiting period (4 secs.)
end reflex andcheck flushing system
flushing takes placeLED flashes during flushing flushing does not take place
replace magnetic valve
replace electronics
water is running constantly
water continues to run
replace electronics
YES
NOreplace electronicboard assembly
replace MV
flushing still doesnot function
MV installed incorrectly (verify flow direction)observe that the minimum water pressure must be 0.3 bar
Spare Parts
6
503 846 shut-off valve
998 608 24V magnetic valve
BurdaTronic U-01 electronic board assemblystainless steel, 230 V power supply
BurdaTronic U-02 electronic board assemblystainless steel, 9 V battery operation
Function
7
Minimum waiting period 4 secs. Pre-flushing as required 1 sec. if last flushing took place more than 5 min. ago
adjustable 0main flushing cyclefrom 1 to 10 secs.
hygiene flushing when not usedfor 24 hours
503 846 shut-off valve
998 608 24V magnetic valve
BurdaTronic U-01 electronic board assemblystainless steel, 230 V power supply
BurdaTronic U-02 electronic board assemblystainless steel, 9 V battery operation
Herbert Burda GmbHKrefelder Straße 87D-40549 Düsseldorf
Tel. +49 211 950 01- 0Fax +49 211 50 05 75
www.burda-online.com