molybkombin umf t4 spray - atlanta · molybkombin umf t4 spray is a ... ejector pins and moving...
TRANSCRIPT
MOLYBKOMBIN UMF T4 SprayAir-drying bonded coating based on MoS2
The data in this product information is based on our general experience and knowledge at the time of printing and is intendedwith technical experience. It constitutes neither an assurance of product properties nor does it release the user from the obligproduct. We recommend contacting our Technical Consulting Staff to discuss your specific application. If required and possibKlüber products are continually improved. Therefore, Klüber Lubrication reserves the right to change all the technical data in
Klüber Lubrication München KG, a member of the Freudenberg group
Publisher and Copyright: Reprints, total or in part, are permitted if source Klüber LubricKlüber Lubrication München KG is indicated and voucher copy is forwarded. Geisenhause
� +49 89 78
Product information 5.554 eCode-No.: 081005
DescriptionMOLYBKOMBIN UMF T4 Spray isan air-drying bonded coating basedon molybdenum disulfide (MoS2)and an organic binder.Once applied and dried, the productshows good adhesion to metalsurfaces and provides a high load-carrying capacity. The dry lubricatingfilm can be used at temperatures upto 450°C.
ApplicationMOLYBKOMBIN UMF T4 Spray is afriction and wear reducing lubricantfor the lubrication of width screwspindles in textile stenter frames.MOLYBKOMBIN UMF T4 Sprayrepels lint, fly dust and dirt thusensuring precise low torque widthadjustment.The product can also be used inworkshops as assembly aid forbearings, bolts, screw connectionsand as a running-in aid for plainbearings and sliding points.MOLYBKOMBIN UMF T4 Sprayeliminates stick-slip in slide andguideways.In the metalforming industry,MOLYBKOMBIN UMF T 4 is used toprotect drawing and cutting toolsagainst wear and extend theirservice life. It is also suitable for theimpregnation of diecasting mouldsand for the lubrication of cores,ejector pins and moving mould partsin pressure and gravity diecastingmachines.
Application notesShake MOLYBKOMBIN UMF T4Spray well before use.All surfaces should be free from oil,grease, water and corrosion prior toinitial lubrication.Keep aerosol can vertical and sprayin thin and uniform layers from adistance of approximately 20 cm.Do not spray on to or near an openflame or any incandescent material.
Minimum shelf lifeThe minimum shelf life is approx. 24months if the product is stored in itsclosed original container in a dryplace.Important: Do note expose to directsunlight and temperatures above50°C!
P4Op1
MOLYBKOMBIN UMF T4 Spray• Dry lubrication of textile
stenter width screw spindles• Assembly aid• Good adhesion to metals• High pressure resistance• Wide service temperature
range
ack sizes00 ml aerosol canriginal container and minimumurchasing quantity:2 x 400 ml aerosol cans
Product data
Base: solid lubricantbindersolventpropellant
MoS2organicacetone
dimethylether
Service temperature range*, °C, approx. -40 to 450
Colour black* Service temperatures are guide values which depend on the lubricant's composition, the intended use and the applicationmethod. Lubricants change their consistency, apparent dynamic viscosity or viscosity depending on the mechano-dynamicalloads, time, pressure and temperature. These changes in product characteristics may affect the function of a component..
to give information oation of performing prle we will be pleasedthis product informatio
ation München KGnerstraße 7, 81379 M76-0, Telefax +49 89
f possible applications to a readereliminary tests with the selected to provide a sample for testing.n at any time without notice.
ünchen, Deutschland7876-333, www.klueber.com
Edition 09.03MA-LSL