mohamed mahmoud abdellatif (cv)
TRANSCRIPT
Page 1 of 4
Mohamed Mahmoud Abdellatif +201276710472/+201006642940 (EGYPT)
Personal Information Egyptian, single, Birth Date: August 28, 1990 Home-Town: Alagamy, Alexandria, Egypt. Military status: exempted
Career Path Objectives Short-term objective: obtain a position that will enable me to observe different mechanical
systems with a delegation of designing, building and monitoring the working process and
checking its accordance to quality standards and proper work procedures.
Long-term objective: seeking a project management position with leadership responsibilities
including problem solving, planning and managing budgets.
Education
Faculty of Engineering, Alexandria University, Egypt.
Bachelor of Science, Mechanical Power Engineering
Graduation year: 2012
Overall grade: good (72.65%)
Project: Brackish water Desalination plant with reverse osmosis technology (RO).
Project grade: excellent.
Work Experience
1-INTEGRATED BIM SERVICES (Egypt)
Job Title: BIM Mechanical Engineer
Duration: OCTOBER 2016 UP Till Now.
Duties:
Setting up goals for the project’s BIM workflow and requirements management
Making modeling for all Mechanical systems such as (HVAC, Firefighting& Plumbing)
Systems using Autodesk Revit MEP.
Study and check all design drawings and compare all the related drawings (MEP, Structural,
Architectural,) also, prepare RFI to solve any technical conflict in design between disciplines.
Running interface check to Coordinate with Structural, Architecture and MEP disciplines
against clashes.
Participate in the process of developing BIM standards for projects across the company.
Making B.O.Q (Bill of Quantities) by using REVIT.
Projects attending:
Muzaffarabad University consists of 26 Buildings
RAWLAKOT District consists of 27 Buildings
Page 2 of 4
2-GAMA FOR Trading &Constructing (Egypt)
Job Title: Mechanical Technical Office Engineer
Client: EMAAR MISR
Duration: July 2016 to OCTOBER 2016.
Projects attended:
MIVIDA 5th Settlement, Cairo Resorts Residential.
Duties:
Interprets design drawings and studies the applicable standards or specifications of the
project, and sending RFI to design consultant in the case of missing in design to resolve issue.
Preparation of builders works drawings to verify locations and levels of mechanical openings
& sleeves penetrations.
Preparation Mechanical shop drawings and material submittals to approved.
3-Egyptian Group For Engineering Consultants (KSA)
Job Title: BIM HVAC Design Engineer
Client: Royal commission in Jubail & Yanbu
Duration: March 2015 to April 2016
Projects attended:
THREE SCHOOLS (ONE BOYS ELEMENTARY & TWO GIRLS ELEMENTARY).
Located in Jalmudah ,ksa . Each school consists of main building and guard house
with built up area of 6000 m2
THREE SCHOOLS (BOYS ELEMENTARY, GIRLS ELEMENTARY & BOYS INTERMEDIATE).
Located in Mutrafiah ,ksa . Each school consists of main building and guard house
with built up area of 6000 m2
TRANSPORTATION CENTER.
Consist of 5 buildings (Administration building, two Service building & two Guard House) with built up area of 2000 m2
CONSTRUCTION OF HOUSING UNITS
Consist of 6 buildings (TYPE (A) &TYPE (B) buildings &Recreation building &security building
& Administration building & Guard House) with area of 15250 m2
ENVIRONMENTAL LABORATORY.
Located in Jubail, ksa . with built up area 900 m2
Duties:
Design HVAC systems according to Royal Commission (RC) manual and International Standards
Calculation cooling & heating loads using Hourly Analysis Program (HAP)
Duct design using duct sizer
Drawing HVAC systems using Autodesk Revit MEP
Make selection for mechanical equipment
Estimating Quantities of Mechanical Systems
Coordinate with other disciplines
Page 3 of 4
4- Khaled Alfagih Consultant Office (KSA)
Job Title: BIM HVAC Design Engineer
Client: Ministry of Health in Al-AHSA (KSA)
Duration: March 2014 to February 2015
Projects attended:
Design & Supervision Health centers of Saudi Ministry of Health in Al-AHSA (KSA).
Duties:
Design HVAC systems according to SAUDI Mechanical Specification for Hospitals and
International Standards
Calculation cooling & heating loads using Hourly Analysis Program (HAP)
Duct design using duct sizer
Drawing HVAC systems using Autodesk Revit MEP
Making selection for mechanical equipment
Estimating Quantities of Mechanical Systems
Supervision of Installation of HVAC Systems according to SAUDI Mechanical Specification for
Hospitals
Coordination with other trades and disciplines.
5-ORASCOM CONSTRUCTION INDUSTRIES (Egypt)
Job Title: Mechanical Site Engineer
Client: EMAAR MISR
Duration: November 2012 to February 2014
Projects attended:
North Coast Marassi Sidi Abdel-Rahman Resorts Residential.
Duties:
Installation of HVAC &PLUMBING systems according to design and international standards
Coordination with other trades and disciplines.
Performing required inspection tests and handing over to consultant.
Coordination with technical office and providing ‘AS-BUILT’ drawings.
Computer Skills
Excellent at Using Microsoft Office Package.
Drawing mechanical system using Autodesk Revit MEP.
Drawing 2D using Autodesk AutoCAD.
Calculating cooling load using Hourly Analysis Program (HAP).
Ducts design using Duct Sizer program.
Fans Selection using Greenheck program.
Duct fitting calculations using RHVAC program.
Hydraulic calculations for Fire Fighting systems using Elite.
Page 4 of 4
Training
West Delta Electricity production (sidikrir) 2010-2011
Alexandria petroleum maintenance (PETROMAINT) 2010-2011
AL EZZ DEKHEILA STEEL COMPANY-ALEXANDRIA 2009-2010
AL EZZ DEKHEILA STEEL COMPANY-ALEXANDRIA 2008-2009
Courses Course
Contents Place
Rotary Equipment pumps-compressors-(gas-turbine) (OGS)
HAZOP Risk identification techniques, procedures (STC)
Piping fundamentals fundamentals, design, components (STC)
Heat exchanger Classification, Applications (SPE)
Petroleum Refining Refining processes, design and operations (SPE)
Language skills Arabic is Mother Tongue.
Good command of English both written and spoken.
Other Skills
Ability to hard working.
High ability to work in a team or work individually under pressure.
Ability to learn new tasks quickly.
Surfing the web for more knowledge especially at engineering.
Memberships
Membership at Saudi Council of Engineers.
Membership at Egyptian Engineers Syndicate.
Valid driving license
All references and documents are available upon request. I certify that all information in this resume is true and complete to the best of my knowledge.