model n° 90230 owner’s manual copy
TRANSCRIPT
![Page 1: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/1.jpg)
Keep this Product ID Number and use when contacting Customer Service:
OWNER’S MANUAL
MODEL N° 90230
COPY
![Page 2: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/2.jpg)
2
Save this owner’s manual for future reference and in the event that the manufacturer has to be contacted.
REGISTER YOUR PRODUCT ONLINE AT WWW.LIFETIME.COM
At Lifetime, we are committed to providing innovative and quality products. While registering, you will
have the opportunity to give us your feedback. Your input is valuable to us.
Lifetime’s Promise to You:
REGISTER today!
**U.S. and Canada customers ONLY**
DO NOT CONTACT THE STORE!CALL OUR CUSTOMER SERVICE DEPARTMENT at
1 (800) 225-3865
Questions or Missing Parts? ID:
INSTRUCTION #1118221 4/10/2013
COPY
![Page 3: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/3.jpg)
3
Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY
DAMAGE AND WILL VOID WARRANTY.
SAFETY INSTRUCTIONS
BEFORE BEGINNING ASSEMBLY
![Page 4: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/4.jpg)
4
SAFE HANDLING OF GLASS BACKBOARDS
BEFORE & DURING ASSEMBLY
GENERAL HANDLING & CARE
HANDLING BROKEN GLASS
At the fi rst sign of breakage:
REMOVING BACKBOARD FROM SYSTEM
WARNINGleast
![Page 5: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/5.jpg)
5
TOOLS AND PARTS REQUIRED FOR THIS ASSEMBLY
*Three adults required to
complete assembly*
Only adults should set up the product. Do not allow children
in the setup area until assembly is complete.
Phillips Screwdriver
Cement Mix
RebarRubber Mallet
9/16” Wrench
Ladder
Tape MeasureShovel
Level
3/4” Socket Wrench
1/2” Socket Wrench
9/16” Socket Wrench 5/16” Allen Wrench
1/4” Allen Wrench 3/8” Alen Wrench
Bricks
Tape
![Page 6: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/6.jpg)
6
This area is located at the top,
left-hand corner of the page
and indicates which tools
and hardware are needed to
complete the assembly steps
on a page.
Note:!
Refer to the following areas throughout the instructions
to assist in the assembly process:
This area is usually located in the
bottom, left-hand corner of a step
and indicates that special attention
is needed to perform a particular
part of a step.
These areas are usually located in
the bottom, right-hand corner of a
step and indicate that damage to
the product or serious injury may
occur if the caution or warning is
not heeded. WARNING
ASSEMBLY GUIDES
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
CAUTION
![Page 7: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/7.jpg)
7
PARTS LISTID Item Description Qty
1
1
11111111
11111
16
![Page 8: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/8.jpg)
8
HARDWARE LISTID Item Description Qty
BCO Pole Assembly Hardware
BCS Backboard & Rim Assembly Hardware
1
BCR Backboard to Pole Assembly Hardware6
64
41
BCT Handle Assembly Hardware1
146314141
11
![Page 9: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/9.jpg)
9
PARTS IDENTIFIER
BGP
DIR
AKZALX
Parts shown at 10% of Actual Size
AKF AKG
AKD
AKI
DIU
![Page 10: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/10.jpg)
10
AJI
Part shown at 5% of Actual Size
PARTS IDENTIFIER
AQC
Parts shown at Actual Size
ALG
DIO
![Page 11: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/11.jpg)
11
Parts shown at 25% of Actual Size
PARTS IDENTIFIER
ALM
ALL
AMA
BGY
BLCAKP
BGR
CYA
DJA
1109
025
10’
9’6
”
9’
8’6
”
7’6
”
8’
![Page 12: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/12.jpg)
12
HARDWARE IDENTIFIERPOLE ASSEMBLY HARDWAREHardware shown at Actual Size
BACKBOARD TO RIM ASSEMBLY HARDWAREHardware shown at Actual Size
CUB
CTY
ANE
ANJ
ADXABK
ABF ABD
![Page 13: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/13.jpg)
13
HARDWARE IDENTIFIER
BACKBOARD TO POLE ASSEMBLY HARDWAREHardware shown at Actual Size
CUG
AQB
ABP
CYF
7”
AEG
CYT
ANZ
AAN
AJZ
![Page 14: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/14.jpg)
14
HARDWARE IDENTIFIERHANDLE ASSEMBLY HARDWAREHardware shown at Actual Size
DXL
7”
AEH
AEG
ANZ
5.4”
DFR
DFS
CYG
AAX
DIJ
CYN
DIQ
DIH
DIN AKH
![Page 15: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/15.jpg)
15
POLE ASSEMBLY
HARDWARE REQUIRED
SEC
1
Hardware shown at Actual Size
CUB
CTY
ANE
PARTS REQUIRED
TOOLS REQUIRED
Parts shown is not to scale
5/16 Allen Wrench
ALG
ALL
Part shown at 25% of Actual Size
9/16” Socket Wrench
30” RebarShovel
Tape Measure Cement Mix
Level
ALM
Bricks
Tape
![Page 16: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/16.jpg)
16
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
1.1
Note: A Ground Sleeve is available as an alternative to cementing
the Pole into the ground. Please contact Customer Service for
more information.!
NO HARDWARE REQUIRED FOR THIS PAGE
![Page 17: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/17.jpg)
17
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
3/8” x 4 1/2” Bolts (CTY) Pole (ALG)
1/2” x 3.91” Spacers (ANE) Pole
Bracket (ALL) 3/8” Nylock Nuts (CUB)
SEC
1.2
ALL
CUBANE
ALG
CTY
Small holes
Large
holes
Note: Make sure the Warning Sticker and the
Pole Bracket face opposite directions.!
CUB
CTY
9/16”
ANE
5/16”
![Page 18: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/18.jpg)
18
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
Rebar
ALM
SEC
1.3
Pole Caps (ALM)
Alignment Frame (BGW)
SEC
1.4
NO HARDWARE REQUIRED FOR THIS PAGE
30” Rebar
BGW
![Page 19: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/19.jpg)
19
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
16”
do not
SEC
1.5
SEC
1.6
Note: Make sure the Pole Cap stays on the
bottom of the Pole throughout the entire
cementing process.
!
NO HARDWARE REQUIRED FOR THIS PAGE
![Page 20: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/20.jpg)
20
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
30” Rebar
NO HARDWARE REQUIRED FOR THIS PAGE
Pole
Cap
SEC
1.7
Note: Make sure the Pole Bracket
faces away from the playing surface.!
WARNING
![Page 21: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/21.jpg)
21
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
1.9
NO HARDWARE REQUIRED FOR THIS PAGE
Alignment Frame (BGW)
SEC
1.10
Note: Slope the concrete away from the Pole
to prevent water buildup around the Pole.!
Playing
Surface
ALG
TOP VIEW BGW
![Page 22: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/22.jpg)
22
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
Alignment Frame (BGW)
SEC
1.11
Note: STOP HERE! The concrete must cure for at least 72 hours (3 days) before
installing the rest of the system. In humid climates or wet weather, allow additional
time for the concrete to cure. Do not proceed until the curing process is complete.!
NO HARDWARE REQUIRED FOR THIS PAGE
![Page 23: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/23.jpg)
23
BACKBOARD TO RIM ASSEMBLYSEC
2
Hardware shown at Actual Size
HARDWARE REQUIRED
Part shown at 10% of Actual Size
PARTS REQUIRED
ALX
ANJ
ADXABK
ABF ABD
Part shown at 5% of Actual Size
AJI
AQB
![Page 24: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/24.jpg)
24
BACKBOARD TO RIM ASSEMBLYSEC
2
PARTS REQUIREDPart shown at 25% of Actual Size
Phillips Screwdriver
TOOLS REQUIRED
AMA
BGY
1/2” Wrench
DJA
BGR (x1)Washer Plate
![Page 25: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/25.jpg)
25
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
Rim Mount Bracket (DJA) Rim Spacer (BGY) Rim (ALX)SEC
2.1
ANJ
ABD
ANJ
ABD
1/2”
DJA
BGY
WARNING
ALX
![Page 26: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/26.jpg)
26
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
2.2
Washer Plate (BGR)
ADX
ADXADX AMA
SEC
2.3
Rim Cover Plate (AMA)
ABK
BGR
ABK
ABK
ABK
1/2”
ABK
![Page 27: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/27.jpg)
27
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
2.4
1/2”
Backboard (AJI)
ABK
ABFABD
ABF
ABD
ABK
AJI
ANJ
ANJ
ABK
ANJ
ABF
Front View Rear View
ABF ABF
Note: Do not overtighten the hardware so that the
7/16”Rubber Washer bulges outward as shown.!CorrectIncorrect
![Page 28: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/28.jpg)
28
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
2.5
Rim Mount Bracket (DJA)
1/2”
AQBABK
AQB
AQBABK
ABK
DJA
![Page 29: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/29.jpg)
29
BACKBOARD TO POLE ASSEMBLY
HARDWARE REQUIRED
SEC
3
Hardware shown at Actual Size
CUG
AQB ABP
CYF
7”
AEG
CYT
ANZAAN
AJZ
![Page 30: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/30.jpg)
30
BACKBOARD TO POLE ASSEMBLY
PARTS REQUIRED
TOOLS REQUIRED
SEC
3
Parts shown at 10% of Actual Size
Rubber Mallet
BLC
Parts shown at 10% of Actual Size
Parts shown at 25% of Actual Size
1/2” Socket Wrench 3/4” Socket Wrench
AQC
Parts shown at Actual Size
BGP (x2)Lower Extension Arm
DIR (x2)Middle Extension Arm
AKD (x2)Upper Extension Arm
3/8” Allen Wrench
ALM
Ladder 3/4” Wrench
![Page 31: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/31.jpg)
31
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
Tie Plate (BLC) Lower Extension
Arm (BGP)
SEC
3.1
BLC
BGP
BGP
BLC
Tie Plate (BLC)
Lower Extension Arm (BGP)
SEC
3.2
NO HARDWARE REQUIRED FOR THIS PAGE
![Page 32: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/32.jpg)
32
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
Extension Arm Caps (AQC)SEC
3.4
AQC
AQC
Lower Extension Arms (BGP)
5/16” x 3/4” Thread-Cutting Bolts (AQB)
Tie Plate (BLC)
SEC
3.3
AQB
AANBGP BGP
BLC
1/2”
AQB
Note: Repeat Sec 3.1-3.4 to assemble the Middle Extension Arms (DIR) .!
AAN
![Page 33: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/33.jpg)
33
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
Note: Tighten the 1/2” Nylock Nut (CYF) until it is fl ush with the end of the Bolt.!
Dark Lithium Grease (AJZ) 1/2” x 7” Bolt (CUG) Lower
Extension Arms (BGP) Rim Mounting Bracket (DJA)
SEC
3.5
CYF ABP
CUG
7”
AEG
ABP
AEGAEGCUG
ABP
CYF
3/4”
3/8”
![Page 34: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/34.jpg)
34
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
3.6Dark Lithium Grease (AJZ) 1/2” x 7” Bolt (CUG)
Middle Extension Arms (DIR) Rim Mounting Bracket (DJA)
Note: Tighten the 1/2” Nylock Nut (CYF) until it is fl ush with the end of the Bolt.!
CYF ABP
CUG
ABP
AEGAEGCUG
ABP
CYF
7”
AEG
3/4”
3/8”
![Page 35: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/35.jpg)
35
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
AKD
AKD
CYT CYF
AEG
AEG
CYFCYT
AKD
AEG
CYFCYT
AKD
SEC
3.7Upper Extension Arms (AKD)
3/4”
3/8”
SEC
3.8Upper Extension Arms (AKD)
AQC
AQC
![Page 36: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/36.jpg)
36
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
3.9 Dark Lithium Grease (AJZ) 1/2” x 7” Bolt (CUG) Pole Cap
(ALM) Pole (ALG)
Upper Extension Arms (AKD)
CAUTION: HAVE TWO ADULTS HOLD THE BACKBOARD IN PLACEUNTIL ASSEMBLY HAS BEEN COMPLETED!
WARNING
CYF ANZ
CUG
7”
AEG
Note: Tighten the 1/2” Nylock Nut (CYF) until it is fl ush with the end of the Bolt.!
ALM
ALG
CUG
ANZ ANZ
AEG
AEG
CYF
3/4”
3/8”
AKD
AKD
![Page 37: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/37.jpg)
37
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
3.10Dark Lithium Grease (AJZ) 1/2” x 7” Bolt (CUG) Middle
Extension Arms (DIR) Pole (ALG)
Note: Tighten the 1/2” Nylock Nut (CYF) until it is fl ush with the end of the Bolt.!
CAUTION: HAVE TWO ADULTS HOLD THE BACKBOARD IN PLACE UNTIL ASSEMBLY HAS BEEN COMPLETED!
CYF ANZ
CUG
7”
AEG
CUG
ANZ ANZ
AEGAEG
CYF
3/4”
3/8”
DIR
DIR
![Page 38: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/38.jpg)
38
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
3.11Dark Lithium Grease (AJZ) 1/2” x 7” Bolt (CUG) Lower
Extension Arms (BGP)
CAUTION: HAVE TWO ADULTS HOLD THE BACKBOARD IN PLACEUNTIL ASSEMBLY HAS BEEN COMPLETED!
CYF ANZ
CUG
7”
AEG
ANZ
AEG
AEGCUG
ANZ
CYF
Note: Tighten the 1/2” Nylock Nut (CYF) until it is fl ush with the end of the Bolts.!
3/4”
3/8”
BGP
![Page 39: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/39.jpg)
39
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
3.12
CAUTION: HAVE TWO ADULTS HOLD THE BACKBOARD IN PLACEUNTIL ASSEMBLY HAS BEEN COMPLETED!
CYF
CUG
7”
AEG
AEGAEGCUG
CYF
Note: Tighten the 1/2” Nylock Nut (CYF) until it is fl ush with the end of the Bolt.!
3/4”
3/8”
![Page 40: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/40.jpg)
40
HANDLE ASSEMBLY
HARDWARE REQUIRED
SEC
4
Hardware shown at Actual Size
DXL
7”
AEH
AEG
ANZ
5.4”
DFR
DFS
CYG
AAX
DIJ
CYN
DIQ
DIH
DIN
AKH
![Page 41: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/41.jpg)
41
HANDLE ASSEMBLY
TOOLS REQUIRED
SEC
4
1/2”, 3/4”, 15/16”
Wrench
PARTS REQUIREDParts shown at 10% of Actual Size
AKF AKG
Parts shown at 25% of Actual Size
CYA
1/4”, 3/8” Allen
Wrench
DIU
Parts shown at Actual Size
DIO
AKI (x1)Handle Assembly
Rubber Mallet
![Page 42: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/42.jpg)
42
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
4.1Gas Spring Cover (AKG) Gas Spring (AKF)
SEC
4.2Gas Spring Cover (AKG) Gas Spring (AKF)
Pole Bracket (ALL)
AKG
CYNDIH
1/2”
AKF
AKG
AKF
DIH CYN
ALL
Note: Tighten the 5/16” Nylock Nut (CYN) until it is fl ush with the end of the Bolt.!
1/4”
![Page 43: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/43.jpg)
43
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
4.3
AEGANZ
Note: DO NOT overtighten the hardware. The Handle Brackets should rotate freely.!
Dark Lithium Grease (AJZ) 1/2” x 5.4” Bolt (DFR) Handle
Brackets (CYA)
AAX
DFR
5.4”3/4”
3/8”
DFR
ANZANZ
AEG
AEGAAX
CYA
CYA
![Page 44: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/44.jpg)
44
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
4.4Dark Lithium Grease (AJZ) 1/2” x 3” Bolt (DFS) Handle
(AKI) Handle Brackets (CYA) 1/2” Plastic Washer
(AEG)
Note: Tighten the 1/2” Centerlock Nut (AAX) until it is fl ush
with the end of the Bolt. Leave a very slight amount of play
in the bolt so the handle can move properly.
!
DFS
AEGAAX
AKI
3/4”
3/8”
AAX
DFS
AEGAEG
![Page 45: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/45.jpg)
45
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
4.5White Silicone Grease (AKH) Trigger Pin (DIN)
Gas Spring (AKF)
DIN
AKF
NO TOOLS REQUIRED FOR THIS PAGE
CAUTION
DIN
![Page 46: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/46.jpg)
46
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
White Silicone Grease (AKH) 1/2” x 3” Bolt (DFS)
1/2” Large Plastic Washers (DIQ)
SEC
4.6
Note: Tighten the Bolt (DFS) so there is some slight play where the Handle meets the Brackets.!
Tube Cap (DIO) Power Flex Spring Assembly (DIU)SEC
4.7
DFS
AAX
3/4”
3/8”
DIQ
DFS
DIQDIQ
AAX
DIO
DIU
CAUTION
![Page 47: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/47.jpg)
47
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
White Silicone Grease (AKH) 5/8” x 3” Bolt (DFS)
Power Flex Spring Assembly (DIU) 1/2”
Centerlock Nut (AAX)
SEC
4.8
DFS
AEGAAX
ANZ
Note: Tighten the 1/2” Centerlock Nut (AAX) until it is fl ush with the end of the
Bolt. Leave a very slight amount of play in the bolt so the handle can move
properly. The Handle Assembly should feel loose once this step is complete.
!
CAUTION
DIU
DFS
ANZ
AEGDIQ DIQ
AAX
AEG
DIQ
3/4”
3/8”
![Page 48: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/48.jpg)
48
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
Dark Lithium Grease (AJZ) 5/8” x 7” Bolt (DXL)
PowerFlex Spring Assembly (DIU) Lower Extension Arms (AKB)
SEC
4.9
Note: Tighten the 5/8” Nylock Nut (CYG) until it is fl ush with the end of the Bolt.!
DIJ
7”
DXL
AEH
15/16”
DIJ
WARNING
DXL AEH
AEH
CYG
CYG
DIU
Note: Use a 1/2” Wrench and a 1/2” x 3/4” Hex Bolt (not provided) threaded onto two 1/2”
Hex Nuts (not provided) to act as an Allen Wrench if a 1/2” Allen Wrench is not available. !
3/8”
![Page 49: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/49.jpg)
49
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
White Silicone Grease (AKH)SEC
4.10
NO TOOLS OR HARDWARE REQUIRED FOR THIS PAGE
AKH
CAUTION
![Page 50: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/50.jpg)
50
FINAL ASSEMBLY
HARDWARE REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
SEC
5
Parts shown at 10% of Actual Size
AKZ
Parts shown at 25% of Actual Size
AKP
![Page 51: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/51.jpg)
51
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
SEC
5.1
Net
(AKZ) Rim (ALX)ALX
AKZ
Note: If a replacement Net is needed, please call our Customer Service Department.
Our Nets are shorter than average to reduce the risk of entanglement.!
NO HARDWARE REQUIRED FOR THIS PAGE
Gas Spring Cover (AKG)
Gas Spring (AJR)
Height Sticker (AKP)
SEC
5.2
AKG
Squeeze
hereSqueeze
here
AKPAJR
Note: Height Sticker (AKP) may be different than the one shown here.!
![Page 52: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/52.jpg)
52
To Adjust the Height of the Hoop:
OPERATION OF HEIGHT ADJUSTMENT SYSTEM
IF RUST HAS PENETRATED THROUGH THE POLE ANYWHERE, REPLACE IT IMMEDIATELY!
POLE CARE AND SYSTEM MAINTENANCE
![Page 53: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/53.jpg)
53
NOTES
![Page 54: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/54.jpg)
54
NOTES
![Page 55: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/55.jpg)
55
ENHANCE YOUR LIFETIME® PURCHASE BY ADDING
ACCESSORIES OR OTHER GREAT PRODUCTS:
Or call: 1-800-424-3865
To purchase accessories or other Lifetime Products, visit us at:
www.lifetime.com
![Page 56: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/56.jpg)
56
FAUTE DE NE PAS SUIVRE CES AVERTISSEMENTS, VOUS RISQUEZ DE CAUSER DES BLESSURES
GRAVES ET/OU DES DOMMAGES À L’ÉQUIPEMENT.
SI NO SE OBEDECEN ESTAS ADVERTENCIAS PUEDEN PRODUCIRSE GRAVES LESIONES Y/O
DAÑOS A LA PROPIEDAD.Le propriétaire doit s’assurer que tous les joueurs
d’utiliser l’équipement en toute sécurité.
WARNING
El propietario del sistema debe asegurarse de que todos los jugadores conozcan y respeten estas reglas
para que el sistema se use en forma segura.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY
DAMAGE.
Owners must ensure that all players know and follow these rules for safe operation of the system.
Cuélguese del aro sólo en forma breve, para recuperar el equilibrio o evitar lesionar a otros jugadores. Suéltese del aro lo más pronto que pueda hacerlo con seguridad. Durante el juego, especialmente al embocar violentamente
de alto, la cara de los jugadores debe mantenerse alejada del tablero, el aro y la red. Pueden producirse lesiones graves si los dientes o la cara entran en contacto con el tablero, el aro o la red. Los jugadores deben usar un protector bucal durante el juego.
Mantenga las manos y los dedos alejados de las piezas movibles cuando regule la altura del sistema.
use joyas (anillos, relojes, collares o gargantillas, etc.) durante el juego. Estos objetos pueden engancharse en la red. permita que la base del poste entre en contacto con
materiales orgánicos. El pasto, los desechos animales, etc., pueden causar corrosión y/o deterioros. Controle el poste y todas las piezas metálicas una vez al
mes en busca de signos visibles de corrosión (oxidación, picaduras, escamado). Elimine todo rastro de óxido y vuelva a pintar con esmalte para exteriores. Si el óxido ha penetrado cualquier pieza de acero, reemplace esa pieza de inmediato. Inspeccione el sistema antes de cada uso para
que los elementos de no estén que no haya desgaste excesivo, inestabilidad ni signos de corrosión. Si encuentra irregularidades, repárelas antes de usar el sistema.
use el sistema para levantar ningún objeto. El mecanismo está para elevar solamente el peso del tablero con el aro. cuelgue nada de la agarradera, el aro, el tablero ni los brazos de elevación, ya que esto puede
vous suspendez pas à l’anneau plus que nécessaire pour retrouver votre équilibre ou éviter de blesser les autres joueurs. Relâchez l’anneau aussitôt que possible. Lors d’un match, particulièrement dans le cas des smashs,
le visage du joueur ne doit pas faire face au panneau, à l’anneau, ni au Le joueur risque de graves blessures si ses dents ou son visage entrent en contact avec le panneau, l’anneau, ou le Les joueurs doivent toujours porter un protège-dents lorsqu’ils jouent. glissez pas, ne grimpez pas, et ne jouez pas sur la base
ou le poteau. Lorsque vous ajustez la hauteur ou l’équipement, gardez
vos mains et doigts loin des pièces mobiles.
portez pas de bijoux (bagues, montres, colliers, etc.) lorsque vous jouez. Ces objets pourraient s’accrocher au
Gardez la base du poteau libre de toute matière organique. L’herbe, les déchets, etc. peuvent la corroder et la détériorer. Une fois par mois, que le poteau et toutes les pièces
en métal ne montrent pas de signes de corrosion (rouille, piqûres, écaillage). Enlevez toute la rouille et repeignez complètement avec une peinture pour extérieur. Si la rouille a pénétré une des pièces en acier, vous devrez remplacer immédiatement la pièce en question. A chaque fois que vous allez utiliser l’équipement,
d’abord l’équilibre, la possibilité de pièces desserrées ou usées, la stabilité de l’équipement et tout signe de corrosion ou réparation nécessaire avant utilisation.
pas l’équipement pour lever ou soulever quoique ce soit. Son mécanisme a été conçu uniquement pour soutenir le poids du panneau et de l’anneau. rien au manche, à l’anneau, au panneau ni aux leviers sous peine d’endommager l’équipement et d’annuler la garantie.
ADVERTENCIA AVERTISSEMENT
Only hang from the rim to regain balance or avoid injuring others. Release the rim as soon as safely possible.During play, especially when performing dunk type activities, keep player’s face away from the backboard, rim, and net. Serious injury could occur if teeth/face come in contact with the backboard, rim, or net. Player should wear a mouth guard during play.Do not slide, climb, or play on pole.When adjusting height or moving system, keep hands and
Do not allow children to move or adjust system.Do not wear jewelry (rings, watches, necklaces, etc.) during play. Objects may entangle in net.
Keep organic material away from pole base. Grass, litter, etc. could cause corrosion and/or deterioration.Once a month check pole and all metal parts for signs of corrosion (rust, pitting, chipping). Completely remove rust and repaint with exterior enamel. If rust has penetrated any steel part, replace that part immediately.Check system before each use for loose hardware, excessive wear, instability, and signs of corrosion and repair before use.
Do not use the system to lift or hoist anything. The mechanism is designed to lift only the weight of the backboard and rim. Do not hang anything from the handle, rim backboard, or lifter arms as this will damage the system and void the warranty.
#FS16500 10/12/2004 www.lifetime.com
![Page 57: MODEL N° 90230 OWNER’S MANUAL COPY](https://reader031.vdocuments.site/reader031/viewer/2022020912/620333c56bafc37d313a6313/html5/thumbnails/57.jpg)
57
LIFETIME BASKETBALL EQUIPMENT6-YEAR LIMITED FACTORY WARRANTY
THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE
UNAVAILABLE OR OBSOLETE.
ALL WARRANTY CLAIMS MUST BE ACCOMPANIED BY A SALES RECEIPT.
REPORT PRODUCT DEFECTS IN WRITING TO:
To register the product, visit our Web site at www.lifetime.com
WARRANTY INFORMATION
www.lifetime.com