mobile hydraulic crane reference copy only - fulford · reference copy only load chart &...
TRANSCRIPT
Reference
Copy Only
CraneSafe Certification
Document #: Mobile Hydraulic Crane Practice
LCR.MH80.LBHTC8660.P1
8 January 2009
mobile hydraulic craNe
link belt hTc 8660
load charT & riggiNg pracTice
CraneSafe Certification + Fulford Harbour Group Tel: 604.952.6033 | www.fulford.ca
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 2
Introduction
These 10 questions are for you to use to help get ready for the load chart and rigging part of the CraneSafe Certification assessment for Mobile Hydraulic Crane.
The questions on your assessment will be different from these but will be presented in the same format as these questions.
Following the questions are load charts and jib rating charts. We have not included all of the charts for this crane - but everything you need to answer the questions is included in the load and jib charts you have here. You do not need the crane manual or full load chart package to answer the questions.
Following the load charts are rigging tables - use these to help answer the rigging questions included in the practice questions. These same rigging charts will be used in your assessment so it is a good idea to become familiar with them.
Attached to the back of this practice exercise is an answer sheet. The answer sheet explains how we arrived at the correct answer and you can use this to help work through any questions you may have gotten wrong.
The crane industry in BC has stated that operators must get a minimum of seven out of ten questions right on the load chart and rigging part of the assessment to be competent.
Operator Information
Operator Name:
Employer:
Make & Model of Crane
Signature:
Assessor Information
Assessor Name:
Date of Assessment:
Place of Assessment:
This section to be completed by Operator
This section to be completed by Assessor
Month Day Year
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 3
Load Chart Questions
What is the net capacity?1.
Outriggers fully extended•
Counterweight – 12,000 pounds•
Lifting over the side•
Main boom length – 85 feet•
Lifting with 40 ton block•
8.5 ton ball suspended from auxiliary head•
Fly stowed•
Radius – 42 feet•
Answer: pounds
Specifications
Hoist line is Type ZB•
?
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 4
What is the maximum radius the gross load can be placed?3.
Outriggers fully extended•
Counterweight – 12,000 pounds•
Lifting over the rear•
Main boom length – 75 feet•
Lifting with 40 ton block•
Fly stowed•
Auxiliary head attached•
Rigging – 350 pounds•
Weight of load – 36,000 pounds•
Answer: feet
What is the net capacity?2.
Outriggers – intermediate extension•
Counterweight – 9,000 pounds•
Main boom length – 60 feet•
Lifting with 40 ton block•
8.5 ton ball suspended from auxiliary head•
Fly stowed•
Radius – 25 feet•
Answer: pounds
?
?
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 5
How many parts of line are required to lift the gross load?5.
Outriggers fully extended•
Main boom length – 55 feet•
Lifting with 70 ton block•
Rigging – 300 pounds•
Weight of load – 61,000 pounds•
Answer: parts
What is the maximum radius the load can be placed when lifting from the main boom?4.
Outriggers fully extended•
Counterweight – 12,000 pounds•
Lifting over the side•
Main boom length – 95 feet•
Lifting with 40 ton block•
34 foot fly erected•
8.5 ton ball suspended from the fly•
Rigging – 150 pounds•
Weight of load – 15,000 pounds•
Answer: feet?
?
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 6
What is the maximum radius the load can be placed when lifting from the 34 foot fly?7.
Outriggers fully extended•
Counterweight – 12,000 pounds•
Main boom length – 85 feet•
Fly offset – 15 degrees•
Lifting with 8.5 ton ball•
Rigging – 200 pounds•
Weight of load – 9,000 pounds•
Answer: inch
What is the net capacity when lifting from the 34 foot fly?6.
Outriggers fully extended•
Counterweight – 12,000 pounds•
Main boom length – 110 feet•
40 ton block suspended from main boom•
Fly offset – 1 degree•
Lifting with 8.5 ton ball•
Main boom angle – 58 degrees•
Answer: pounds
?
?
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 7
A 9,000 pound pipe is to be lifted using two wire rope slings in a basket hitch configuration.8.
The sling angle is 60 degrees.
What is the size of wire rope slings required?
Answer: inch
What is the minimum size of nylon web slings required to lift a load weighing 3,700 pounds? 9.
The two-leg bridle is choked at a 45 degree angle.
Answer: inch
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 8
What is the minimum size of the two eye bolts required to lift a load of 5,500 pounds? 10.
The angle of pull is 45 degrees.
Answer: inch
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 9
Link-Belt HTC 8660 Telescopic Crane
Load Charts
������������ ���� ����������� ���� ����������� ���� ������� ������� ���� ���
���������� ������������� ���� ������ �������� ����������� ���������������� ���� ������� � ���������� ������ ����� ���� ������� �����
���������������������������������������
OPERATING INSTRUCTIONS���������� ���������������������������������������������������
������� �������� ��� ����� ������ ��� ����������
������������� ���� ��������� ����������������������� ��� ���� ������ ��� ���� ��� ��������
�������������������������������������������������
�������������������������� ������������� ���������� ���� ��� ���������� ��
����������� ��������� ��� ������������ ���������
���� ������������ ��� ����� ������ ����� ��� ������������� ����� ���� ������������ ��� ���
���������������������������������������������
����� ������������ � ��� �������������� �������������������������������������������������������
�� ���� ��������� ���� ������ ���������� ����������
���������������������������������������������������������� ����������� ��������� ��������� ���������
���������������������������������������
�� ���������� �������������������������������������
������������������������������������������
��������� �����������������������������������������������
��������� � ���������� ��� ���� ������� ��� ���
�����������������������������������������������
�������������������������������������������������
��� ������ ��� ������� ���� ����� ��� �� ������� ���������������
�� ��������������������������������������������������
����������������������������������������������������� ��� ��������� ��� ���� ����� �������� �����
����������� ������������� ���������� ��� �����
���������������������������������������������������������������
�� ������������������������������������������������
���� ������� ���� �������� ����� ������ �����������������������������������������������������
������� ����� ������ �������� �� ��������� �������
������������ �������������������������������������������������
�������������������������������������������
����������������������������
�� �������������������������������������������������������������������������������������������������
����������������������������������������������
������������������������������������������������ ��������������������������������������������������
����������������������
�� ����� ����������� ��� ��������� �������������������������������������������������������������
����������������������������������������������������
���������������������������
�� ������� �������� ��� ��� ������������� ��������������������� ������������ ��� ������� ������ ��� �������
������������������� ������ ������������������� ��
�����������������������������������������
������������ �����������������������������������������������������
���������� � ��� ���� ���� ���� ������ ��� ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� ����������� ��� �� �������� ������� ��� ����������������������������������������������������������������������������������������������������������� ����� ��� ����������� ���������������������������� ������� ��� ���� ��� ������ �������� ������������������� ��� ������ � ���� ���������� ������������������������������������������������������������ ���� ���� ���� ����� ������ ��� ����������� ��� ��������� ��� ��� ��������� � ������ ����� ������� �����������������������������������������������������������
�� ����������������������������������������������������������� ��� ���� ������� ���� ��� ���� �������������� ������ �������� ����������� ������ ��������������� ��������� ��� ������ ������������������������������������������������������������������������ ������������� ����� ������������������� �������� ����������� ������ ��� ������ ��� ��������������������������������������������������������������������������������������������������������
�� ������ �������� � ����������� ��� ���� ������� ����������� ���� ����� ������� ���� ������ ��� ���������������������������������������������������������������� ���������������� ������������� ��� ������������������������������������������������������������������������������������������������������ ����� ������ ���� ������ ��� ���������� ������������� ����������� ���� �������� ��� �� ���������������������������������
�� ������������������������������������������������������������������������������������������������������������������������������������������������������������� ���������������������� ���������� ����������������������������������������������������������������� ����������� ����������� �������������� �������� ��� ���� ������ � ���� �������� ��� ������� ������������������������������������������������������������������������������������������
2HTC-8660
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 10
�� ������ �������� ����������� ���� ������ ��� ���������������������������������������������������������� ��������������������� ����������� ����������������
�� ��������������������������������� �����������������������
�� ��� ���� �������� ��� ������ ��� ����� �������
����������������������������������������������������� ���� ����������������� �������������� ������
�������������������
�� ���������������������������������������������
���� ���������� �������� ��� ���������� ��� �������������������������������������������������������
��������������������������������������������������
�������������������������������������� ���� ����� ����� ����������� ����� ������� ����
���������������������������������������������������
��������������������� ��������� ������������ ������������ ������� ���
����� ������� ����� ������� ��� ����� �������
������������������������������������ ���� ��������������� ���������������������������
����������������� ��������������������������������������������������
���� �������� ���� ������������ ����� ���� ����� ��
��������������������������������������������������
������� ��������� �������� �������� ��� ��������������� ��� ������� ���������� �����������
����������� ��� ����������� ���������� ����� ������
����������������������������������������������������������������������������������
��� ���������������������������������������������������
������������������������������������������������������������������������������������������
�������������������������������������������
��� ���������������������������������������������������������������������������������������������������
��� ������ ��������� ��� ���������� ��� ��������� ��
���������������������������������������������������������������������������������������������
������������������
��� ����������������������������������������������
����������������������������������������� ������ �������� ����������� ���� ������ ��� �������
����������������������������������������������
��������� � ���� �������� ����� �������� ������������� ����� ����� ���������� ��� ����������
���������� ���� ����� ��� ���������� ���� ����
������� ������� � ���� �������� ������ �������� �������������������������������������������������������
�������������������������������������������������
������������
��� ��������������������������������������������
������� ����� ����� ��� �������������� ��� ���
���������� �������� � ���� ����� ������� ��������������� ������� ��� �������� ��� �������� ���
�������������������������������������������������
����� ������ ��� ���� ���������� ������ � ���� �������������������������������������������������������
��� ��������������������������������������������������
���������������������������������������������������������������������������������������������������
�������������������������������������������������
���������������������������������������������������������
��� ��������������������������������������������������
��������������������������������������������������
���������������������������������������������������������������������������������������������
�������������������������������������������
��� ���������������������������������������������������������������������������������������������������
���� ������ ����������� ��� ���� ������� ����������
������������������������������������ ������ ���������������������� ���������������� ����
����������������������������������������������������
�����������������������������������������������������������������������������������������������
������������������������������������������������
�����������������������������������������������������������������������������������������������
������ ����� �������� ���� ���� ����� ����� ��
����������� ����� ���������� � ���� �������� ����
�������������������������������
�������������� ����� �������� � ����������� ��������� ����� �
����������������������������������������������������
����������������������������������������������������
���������������������������������������
�� ������������������� � ���� ������ �������� �������� ����� �������� ���� ����������� ����� ������
�����������������������������������
�� �����������������������������������������������������������������������������������������������
���������������������
�� ������������������������������������������������� ������� ��������� ������ �������� ������� ��� ���
�����������
�� �����������������������������������������������������������������������������������������������
�� ��������������������������������������������������
�������������������������������������������������
������������� ���������������������������������������������������
�� ������������������������������������������������
����������������������������������������������
3HTC-8660
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 11
These charts are for assessment purposes only and should not be used to operate a crane. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
WINCH PERFORMANCEWinch Line Pulls
Two Speed Winch Drum Rope Capacity (Ft.)
Wire Rope Low Speed High SpeedWire RopeLayer Available Lbs.* Available Lbs. Layer Total
1 16,348 7,711 110 1102 15,112 7,090 119 2293 13,985 6,561 129 3584 13,014 6,105 138 4965 12,169 5,709 148 6446 N/A N/A 158 802*Maximum lifting capacity: Type RB Rope=12,920 Type ZB Rope=15,600
WIRE ROPE CAPACITYMaximum Lifting Capacities Based On Wire Rope Strength
Parts 3/4” 3/4”of
Line Type RB Type ZBNotes
1 12,920* 15,600 Capacities shown are in pounds and work-2 25,840 31,200 ing loads must not exceed the ratings on the
capacity charts in the Crane Rating Manual.3 38,760 46,800
capacity charts in the Crane Rating Manual.Study Operator’s Manual for wire rope in-
4 51,680 62,400Study Operator’s Manual for wire rope in-spection procedures.
5 64,600 79,000 *Use of swivel end with 1 part of line is not6 77,520 93,600 recommended.
7 90,440 109,2008 103,360 124,8009 116,280 140,40010 129,200 156,000
LBCE DESCRIPTION TYPE RB 18 X 19 Rotation Resistant – Extra Improved Plow Steel – Preformed Right
Lay – Regular Lay, Swaged
TYPE ZB 36 X 7 Rotation Resistant – Extra Improved Plow Steel – Right Lay –Regular Lay
HYDRAULIC CIRCUIT PRESSURE SETTINGSFunction Pressure (PSI)
Front And Rear Winch 2750Outriggers 3000Boom Hoist 2900Telescope 3000Swing 1500Steering 2000Bumper Outrigger 650Pilot Control 500Counterweight Removal 1500
5HTC-8660
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 12
These charts are for assessment purposes only and should not be used to operate a crane. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
WORKING AREAS
Center Of Rotation
Note: These Lines Determine The Limiting Position Of Any Load For Operation Within Working Areas Indicated.
LongitudinalC of HTCL
LongitudinalC of HTCL
HTC On Tires
Boom Centered Over Rear
Center Of Rotation
HTC On Outriggers
C BoomL
C Rear AxleL
Side
Side
Rear
360�Chart
C Front AxleL
Front
C Outrigger Pontoon
L
See Note
See Note
CAPACITY DEDUCTIONS FOR AUXILIARY LOADHANDLING EQUIPMENT
Load Handling Equipment Weight (Lbs.)
Auxiliary Head Attached 100
40 Ton Quick Reeve 4 Sheave Hook Block (See Hook Block For Actual Weight) 720
60 Ton Quick Reeve 4 Sheave Hook Block (See Hook Block For Actual Weight) 1100
70 Ton Quick Reeve 5 Sheave Hook Block (See Hook Block For Actual Weight) 1400
8.5 Ton Hook Ball (See Hook Ball For Actual Weight) 360
Lifting From Main Boom With:34 Ft. Or 56 Ft. Fly Stowed On Base (See Operation Note 4) 0
34 Ft. Offset Fly Erected But Not Used 4200
56 Ft. Offset Fly Erected But Not Used 7300
Lifting From 34 Ft. Offset Fly With:
22 Ft. Fly Tip Erected But Not Used PROHIBITED
22 Ft. Fly Tip Stowed On 34 Ft. Offset Fly PROHIBITED
Note: Capacity deductions are for Link–Belt supplied equipment only.
6HTC-8660
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 13
These charts are for assessment purposes only and should not be used to operate a crane. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Rated Lifting Capacities In PoundsOn Fully Extended Outriggers
See Set Up Note 2.BOOM MODE “B”
12,000# COUNTERWEIGHT
35.5 Ft. To 55 Ft. Main Boom35.5 Ft. 45 Ft. 55 Ft.
LoadRadius
InFeet
LoadedBoomAngle(Deg.)
360° OverRear
LoadedBoomAngle(Deg.)
360° OverRear
LoadedBoomAngle(Deg.)
360° OverRear
LoadRadius
InFeet
9 70.5 120,000 120,000 910 68.5 108,900 108,900 73.0 42,000 42,000 76.5 42,000 42,000 1012 65.0 96,900 96,900 70.5 42,000 42,000 74.5 42,000 42,000 1215 59.5 82,700 82,700 66.5 42,000 42,000 71.5 42,000 42,000 1520 49.5 64,500 64,500 59.5 42,000 42,000 66.0 42,000 42,000 2025 37.5 48,300 49,800 51.5 42,000 42,000 60.0 42,000 42,000 2530 20.0 33,500 37,700 42.5 34,700 39,000 53.5 35,300 39,500 3035 32.0 26,000 29,800 46.5 26,600 30,500 3540 15.5 20,000 23,500 38.5 20,800 24,300 4045 29.0 16,600 19,700 4550 14.0 13,400 16,200 50
Min. BoomAngle/Cap. 0 19,900 19,900 0 14,300 14,300 0 10,200 10,200 Min. Boom
Angle/Cap.
65 Ft. To 85 Ft. Main Boom65 Ft. 75 Ft. 85 Ft.
LoadRadius Loaded Loaded Loaded
LoadRadius
In Boom 360° Over Boom 360° Over Boom 360° Over InFeet Angle
(Deg.)Rear Angle
(Deg.)Rear Angle
(Deg.)Rear Feet
9 910 1012 77.0 42,000 42,000 1215 74.5 42,000 42,000 77.0 42,000 42,000 1520 70.0 42,000 42,000 73.0 42,000 42,000 75.5 35,900 35,900 2025 65.5 42,000 42,000 69.0 41,700 41,700 72.0 31,500 31,500 2530 60.0 35,600 39,800 65.0 35,800 37,100 68.5 28,100 28,100 3035 54.5 26,900 30,800 60.5 27,100 30,900 64.5 25,400 25,400 3540 49.0 21,200 24,700 56.0 21,400 24,900 61.0 21,500 23,000 4045 42.5 17,000 20,200 51.0 17,200 20,400 56.5 17,400 20,500 4550 35.5 13,900 16,800 45.5 14,100 17,000 52.5 14,300 17,200 5055 26.5 11,500 14,000 40.0 11,800 14,400 48.0 12,000 14,500 5560 13.0 9,400 11,800 33.0 9,800 12,200 43.0 10,000 12,400 6065 25.0 8,200 10,400 37.5 8,400 10,700 6570 12.5 6,800 8,800 31.5 7,100 9,100 7075 23.5 5,900 7,900 7580 12.0 4,900 6,700 80
Min. BoomAngle/Cap 0 7,400 7,400 0 5,400 5,400 0 3,900 3,900 Min. Boom
Angle/CapNote: Refer To Page 8 For “Capacity Deductions” Caused By Auxiliary Load Handling Equipment.
4HTC-8660
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 14
These charts are for assessment purposes only and should not be used to operate a crane. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Rated Lifting Capacities In PoundsOn Fully Extended Outriggers
See Set Up Note 2.BOOM MODE “B”
12,000# COUNTERWEIGHT95 Ft. To 110 Ft. Main Boom
95 Ft. 105 Ft. 110 Ft.Load
Radius Loaded Loaded LoadedLoad
RadiusRadiusIn
LoadedBoom 360° Over
LoadedBoom 360° Over
LoadedBoom 360° Over
RadiusIn
Feet Angle(Deg.)
360 Rear Angle(Deg)
360 Rear Angle(Deg.)
360 Rear Feet
20 77.5 31,800 31,800 20
25 74.5 28,300 28,300 76.0 25,700 25,700 77.0 22,600 22,600 25
30 71.0 25,300 25,300 73.5 23,100 23,100 74.5 22,100 22,100 30
35 68.0 22,800 22,800 70.5 20,900 20,900 71.5 20,000 20,000 35
40 64.5 20,800 20,800 67.5 19,000 19,000 69.0 18,300 18,300 40
45 61.0 17,500 19,000 64.5 17,400 17,400 66.0 16,700 16,700 45
50 57.5 14,400 17,300 61.5 14,500 15,900 63.0 14,500 15,200 50
55 53.5 12,100 14,600 58.0 12,200 14,700 60.0 12,200 13,900 55
60 49.5 10,100 12,600 54.5 10,200 12,600 57.0 10,300 12,400 60
65 45.5 8,600 10,800 51.0 8,700 10,900 53.5 8,700 10,900 65
70 41.0 7,200 9,300 47.5 7,300 9,400 50.0 7,400 9,500 70
75 35.5 6,100 8,100 43.5 6,200 8,200 46.5 6,300 8,200 75
80 30.0 5,100 6,900 39.0 5,300 7,100 42.5 5,300 7,100 80
85 22.5 4,300 6,000 34.0 4,400 6,100 38.0 4,500 6,200 85
90 11.5 3,500 5,100 28.5 3,700 5,300 33.5 3,800 5,400 90
95 21.5 3,000 4,500 28.0 3,100 4,600 95
100 11.0 2,400 3,900 21.5 2,500 3,900 100
Min.BoomAngle/Cap.
0 2,700 2,700 4.5 17.0
Min.BoomAngle/Cap.
Note: Refer To Page 8 For “Capacity Deductions” Caused By Auxiliary Load Handling Equipment.
5HTC-8660
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 15
These charts are for assessment purposes only and should not be used to operate a crane. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
15�Offset
1� Offset
34 Ft. Offset Fly30�
Offset
85 Ft. Main Boom
Rated Lifting Capacities In PoundsOn Fully Extended Outriggers
See Set Up Note 2.
BOOM MODE “B”12,000# COUNTERWEIGHT
85 Ft. Main Boom + 34 Ft. Offset Fly
1� Offset 15� Offset 30� OffsetLoad Load
RadiusIn
LoadedBoom �
LoadedBoom �
LoadedBoom �
RadiusInIn
FeetBoomAngle 360� Boom
Angle 360� BoomAngle 360� In
FeetFeet Angle(Deg.)
Angle(Deg.)
Angle(Deg.)
Feet
25 77.5 18,600 25
30 75.0 17,000 30
35 73.0 15,600 76.5 12,000 35
40 70.5 14,500 74.0 11,400 77.5 9,400 40
45 68.0 13,600 71.5 10,800 75.0 9,100 45
50 65.0 12,700 69.0 10,400 72.5 8,800 50
55 62.5 11,900 66.0 9,900 69.5 8,400 55
60 60.0 11,100 63.5 9,500 67.0 8,100 60
65 57.0 9,900 60.5 9,100 64.0 7,800 65
70 54.0 8,500 57.5 8,800 61.0 7,500 70
75 50.5 7,400 54.5 7,900 57.5 7,300 75
80 47.0 6,400 51.0 6,900 54.5 7,100 80
85 43.5 5,600 47.5 6,000 50.5 6,300 85
90 40.0 4,800 43.5 5,200 46.5 5,500 90
95 35.5 4,200 39.5 4,500 42.0 4,700 95
100 31.0 3,600 34.5 3,800 37.0 4,000 100
105 26.0 3,100 29.5 3,300 31.0 3,400 105
110 19.0 2,600 22.5 2,700 110
Min. BoomAngle/Cap. � ����� � ����� � �����
Min. BoomAngle/Cap.
Note: Refer To Page 8 For “Capacity Deductions” Caused By Auxiliary Load Handling Equipment.
6HTC-8660
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 16
These charts are for assessment purposes only and should not be used to operate a crane. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
15�Offset
1� Offset
34 Ft. Offset Fly
30�Offset
110 Ft. Main Boom
Rated Lifting Capacities In PoundsOn Fully Extended Outriggers
See Set Up Note 2.
BOOM MODE “B”12,000# COUNTERWEIGHT
110 Ft. Main Boom + 34 Ft. Offset Fly1� Offset 15� Offset 30� Offset
Load LoadRadius
InLoadedBoom �
LoadedBoom �
LoadedBoom �
RadiusInIn
FeetBoomAngle 360� Boom
Angle 360� BoomAngle 360� In
FeetFeet Angle(Deg.)
Angle(Deg.)
Angle(Deg.)
Feet
35 76.5 10,500 3540 74.5 10,500 4045 72.5 10,500 76.0 9,800 4550 70.5 9,800 74.0 9,000 77.0 8,300 5055 68.5 8,900 71.5 8,200 74.5 7,700 5560 66.5 8,200 69.5 7,600 72.5 7,100 6065 64.0 7,500 67.5 7,000 70.5 6,600 6570 62.0 6,900 65.0 6,500 68.0 6,200 7075 59.5 6,400 62.5 6,100 65.5 5,800 7580 57.0 6,000 60.5 5,700 63.0 5,400 8085 54.5 5,300 58.0 5,300 60.5 5,100 8590 52.0 4,500 55.5 5,000 58.0 4,800 9095 49.0 3,900 52.5 4,300 55.5 4,600 95100 46.5 3,300 49.5 3,700 52.5 4,000 100105 43.5 2,800 46.5 3,100 49.0 3,400 105110 40.0 2,300 43.5 2,600 45.5 2,800 110115 40.0 2,200 42.0 2,300 115120 38.0 1,900 120
Do Not Lower 34 Ft. Offset Fly In Working Position Below 36° Main Boom Angle Unless Main BoomLength Is 88 Ft. Or Less, Since Loss Of Stability Will Occur Causing A Tipping Condition.
�������
Note: Refer To Page 8 For “Capacity Deductions” Caused By Auxiliary Load Handling Equipment.
8HTC-8660
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 17
These charts are for assessment purposes only and should not be used to operate a crane. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Rated Lifting Capacities In PoundsOn Intermediate Outriggers
See Set Up Note 2.BOOM MODE “B”
9,000# COUNTERWEIGHT35.5 Ft. To 45 Ft. Main Boom
35.5 Ft. 45 Ft.Load
Radius Loaded LoadedLoad
RadiusRadiusIn
LoadedBoom 360°
LoadedBoom 360° In
Feet Angle(Deg.)
360 Angle(Deg.)
360 Feet
10 68.5 112,800 73.0 42,000 10
12 65.0 99,600 70.5 42,000 12
15 59.5 62,800 66.5 42,000 15
20 49.5 35,100 59.0 36,000 20
25 37.5 22,600 51.5 23,700 25
30 20.0 15,300 42.5 16,500 30
35 32.0 11,900 35
40 15.5 8,600 40
Min.BoomAngle/Cap. 0 12,900 0 7,600 Min.Boom
Angle/Cap.
55 Ft. To 65 Ft. Main Boom55 Ft. 65 Ft.
LoadRadius Loaded Loaded
LoadRadiusRadius
InLoadedBoom 360°
LoadedBoom 360°
RadiusIn
Feet Angle(Deg.)
360 Angle(Deg.)
360 Feet
10 76.5 42,000 10
12 74.5 42,000 77.0 42,000 12
15 71.5 42,000 74.5 42,000 15
20 65.5 36,500 69.5 36,800 20
25 59.5 24,200 65.0 24,500 25
30 53.0 17,200 59.5 17,500 30
35 46.0 12,600 54.5 13,000 35
40 38.5 9,400 48.5 9,800 40
45 28.5 7,000 42.5 7,400 45
50 14.0 5,000 35.0 5,600 50
55 26.5 4,100 55
60 13.0 2,800 60
Min.BoomAngle/Cap. 0 4,400 0 2,400 Min.Boom
Angle/Cap.
Note: Refer To Page 8 For “Capacity Deductions” Caused By Auxiliary Load Handling Equipment.
4HTC-8660
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 18
Wire Rope Slings
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 19
Chain Slings
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 20
Nylon Web Slings
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 21
Eye Bolts
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group 22
Hand Signals
Hand signals for hoist and crane operations
Page 1 of 2
If hand signals are used between a signaller and the operator of a crane or hoist to control hoisting operations,
the following signals should be used:
TG 07-29
STOP
RAISETHEBOOMANDLOWERTHELOAD
LOWERTHEBOOMANDRAISETHELOAD
HOIST
EXTENDBOOM
RAISEBOOM
SWING MOVESLOWLY DOG(STOP)EVERYTHING
LOWER
RETRACTBOOM
LOWERBOOM
Armextended,fingersclosed,
thumbpointingupward.
Armextended,pointin
directionofswingofboom.
Useonehandtogiveanymotionsignalandplace
otherhandmotionlessinfrontofhandgivingthe
motionsignal(hoistslowlyshownasexample)
Clasphandsinfrontofbody.
Armextended,fingersclosed,
thumbpointingdownward.
Witharmextended,thumb
pointingup,flexfingersin
andoutaslongasload
movementisdesired.
Witharmextended,thumb
down,flexfingersinand
outaslongasload
movementisdesired.
Armextended,fingersclosed,
thumbpointingupward,other
armbentslightlywithforefinger
pointingdown,androtatehand.
Armextended,fingersclosed,
thumbdown,otherarm
vertical,forefingerupward
androtatehand.
Armextended,palmdown,movehandhorizontal. Withforearmvertical,finger
pointingup,movehandin
smallhorizontalcircles.
Bothfistsinfrontofbody,
withthumbspointing
outward.
Witharmextendeddown,
moveforefinger;pointing
down,movehandincircles.
Bothfistsinfrontofbody,
withthumbspointing
towardeachother.
TOOLBOX MEETING GUIDE
Workers’ Compensation Board of B.C.
!
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group
Answer Key
Answer: 1. 16,220 pounds
Deductions from Gross Capacity
Block 720 pounds
Ball 360 pounds
Auxiliary head 100 pounds
1,180 pounds
The gross capacity at a 45 foot radius is 17,400 – 1,180 = 16,220 pounds.
Answer: 2. 23,020 pounds
Deductions from Gross Capacity
Block 720 pounds
Ball 360 pounds
Auxiliary head 100 pounds
1,180 pounds
Read Operation #9
The gross capacity at a 25 foot radius, 55 feet of boom is
24,200 – 1,180 = 23,020 pounds.
Answer: 3. 25 feet
Gross Load
Block 720 pounds
Auxiliary head 100 pounds
Rigging 350 pounds
Load 36,000 pounds
37,170 pounds
The gross capacity at a 25 foot radius is 41,700 pounds.
AK1
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group
Answer: 4. 40 feet
Gross Load
Block 720 pounds
Fly erected 4,200 pounds
Ball 360 pounds
Rigging 150 pounds
Load 15,000 pounds
20,430 pounds
The gross capacity at a 40 foot radius is 20,800 pounds.
Answer: 5. 5 parts
Gross Load
Block 1,400 pounds
Rigging 300 pounds
Load 61,000 pounds
62,700 pounds
5 parts of line are required to lift a gross load of 62,700 pounds.
Answer: 6. 4920 pounds
Deductions from Gross Capacity
Block 720 pounds
Ball 360 pounds
1,080 pounds
The gross capacity at a 57 degree boom angle is
6,000 – 1,080 = 4,920 pounds.
AK2
Reference
Copy Only
Load Chart & Rigging PRACTICE Mobile Hydraulic Link-Belt HTC 8660 Telescopic Crane (1)
www.fulford.ca CraneSafe Certification + Fulford Harbour Group
Answer: 7. 55 feet
Gross Load
Ball 360 pounds
Rigging 200 pounds
Load 9,000 pounds
9,560 pounds
The gross capacity at a 55 foot radius is 9,900 pounds.
Answer: 8. 7/16 inch
9,000 pound load divided by 2 = 4,500 pounds.
The capacity of one 7/16 inch sling is 6,000 pounds.
6,000 x 2 = 12,000 pounds
Answer: 9. 4 inch
The capacity of a 4 inch, 2 leg bridle is 6,220 pounds.
Sling capacity is reduced by 25% when choked.
6,220 x .75 = 4,665 pounds
Answer: 10. 1-1/4 inch
5,500 pound load divided by 2 = 2,750 pounds.
The capacity of one 1-1/4 inch eyebolt is 3,800 pounds.
3,800 x 2 = 7,600 pounds
AK3