mixed scattering matrix: properties and applications · mixed scattering matrix: properties and...
TRANSCRIPT
![Page 1: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/1.jpg)
1
Dr. A.S.Rukhlenko
Neuchâtel, 2005
www.intraSAW.com
Mixed Scattering Matrix: Properties and Applications
![Page 2: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/2.jpg)
2
Outline
Introduction
1. Admittance, Wave Scattering, and Mixed ScatteringMatrices of the Multi-Port Network
2. Mixed Scattering Matrix of a SAW Transducer
3. SAW Filter Simulation
4. Modeling in the Quasi-Static Approximation
5. Modeling of Reflective SAW Transducers (COM-Analysis)
Conclusions
![Page 3: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/3.jpg)
3
Part 1. Admittance, Wave Scattering, and Mixed Scattering Matrices of the
Multi-Port Network
![Page 4: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/4.jpg)
4
Multi-Port Network
a1b
1
I1
V1 V 2
b 2a 2
I 2
b Na N bk
ak
V NV
kIkI N
N-port network[S], [Y], [M]
1 2
kN
B=SA (scattering matrix)I =YV (admittance matrix)
Fig. 1. An arbitrary N-port microwave network specified in terms of the S- and Y-matrices
![Page 5: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/5.jpg)
5
Wave Scattering and Admittance Matrices
1 11 12 1 1
2 21 22 2 2
1 2
N
N
N N N NN N
b s s s ab s s s a
b s s s a
⎡ ⎤ ⎡ ⎤ ⎡ ⎤⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥=⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎣ ⎦ ⎣ ⎦ ⎣ ⎦
……
…
A=[a1 a2 … aN]T vector of the incident waves B=[b1 b2 … bN]T vector of the reflected wavesI= [I1 I2 … IN]T vector of the terminal currentsV=[V1 V2 …VN]T vector of the terminal voltagesS=[sik] scattering matrix (dimensionless)Y=[Yik] admittance matrix (W-1)
(1)
(2)
(3)
(4)
Scattering Matrix Admittance Matrix
B=SA I=YV
1 11 12 1 1
2 21 22 2 2
1 2
N
N
N N N NN N
I y y y VI y y y V
I y y y V
⎡ ⎤ ⎡ ⎤ ⎡ ⎤⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥=⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎣ ⎦ ⎣ ⎦ ⎣ ⎦
……
…
![Page 6: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/6.jpg)
6
Mixed Scattering Matrix
⎡ ⎤⎡ ⎤ ⎡ ⎤ ⎡ ⎤⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎣ ⎦ ⎣ ⎦ ⎣ ⎦⎣ ⎦
aa ae aa ae
ea ee ea ee
B M M M MA= M=
I M M M MV(5)
11 12 1 1, 1 1, 2 1,1
21 22 2 2, 1 2, 2 2,2
1 2 1, 1 , 2 ,
1,1 1,2 1, 1, 1 1, 2 1,1
2,1 2,22
m m m m n
m m m m n
m m mm m m m m m m nm
m m m m m m m m m m n
m m
n
m m m m m mbm m m m m mb
m m m m m mbm m m m m mIm mI
I
+ + +
+ + +
+ + + +
+ + + + + + + + +
+ +
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥ =⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
… ……
…… ……
1
2
1
2, 2, 2 2, 2
,1 ,2 , , 2 ,
m
m m m m m m n
m n m n m n m m n m m n m n n
aa
aV
m m m V
m m m m m V
+ + + + +
+ + + + + + +
⎡ ⎤ ⎡ ⎤⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎣ ⎦⎣ ⎦
…
…
(6)
Mixed scattering matrix M is a mixed units hybrid of the scattering matrixS and admittance matrix Y.
![Page 7: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/7.jpg)
7
Nomenclature
m number of the acoustic wave portsn number of the electric portsN=m+n total number of the portsA=[a1 a2 … am] vector of the incident waves on the acoustic portsB=[b1 b2 … bm] vector of the reflected waves from the acoustic
portsI =[I1 I2 … In] vector of the terminal currents on the electric portsV=[V1 V2 … Vn] vector of the terminal voltages on the electric portsM mixed scattering matrix of size N x NMaa acoustic matrix block of size m x m (dimensionless)Mae acoustoelectric matrix block of size m x n (mixed units)Mea electroacoustic matrix block of size n x m (mixed units)Mee electric matrix block of size n x n (W-1)
![Page 8: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/8.jpg)
8
Generalized Wave Amplitudes and Electric Variables
Variables Matrix Scalar
Incident and reflected waves
Terminal current and voltages
Characteristic admittance
Average delivered power
⎧⎪⎪⎪⎪⎪⎨⎪⎪⎪⎪⎪⎩
0 0
0 0
1A = ( Y V+ Z I)21B = ( Y V - Z I)2
⎧⎪⎪⎪⎪⎨⎪⎪⎪⎪⎩
0
0
I = Y (A -B)V = Z (A+B)
01
02
0
10 0
0 00 0
0 0 00 0 N
YY
Y
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
− ==Y Z
……
…
Re
Re
*
*
* *
1P = VI =21 (A + B)(A - B) 21 1P = AA - BB2 2
=
1( )21( )2
k ok k ok k
k ok k ok k
a Y V Z I
b Y V Z I
⎧⎪⎪⎪⎪⎪⎪⎨⎪⎪⎪⎪⎪⎪⎩
= +
= −
( )( )
k ok k k
k ok k k
I Y a bV Z a b
⎧⎪⎪⎪⎪⎨⎪⎪⎪⎪⎩
= −= +
0 01/k kY Z=
*
* *
22
1 21 ( )( - )21 12 2
k k k
k k k k
k k k
P Re V I
Re a b a b
P a b
= =
= +
= −
BA*-AB*=2ImBA* purely imaginary.
bk ak*-ak bk*=2Im bk ak* purely imaginary.
(7) (8)
(10)(9)
(12)(11)
(14)(13)
![Page 9: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/9.jpg)
9
Conversion Between Admittance, Scattering, andMixed Scattering Matrices
S Y Me -1M -M (Y +M ) Maa ae ee ea0
e -1 e2M (Y +M ) Yae ee0 0e e -1- Y (Y +M ) Mee ea0 0
e e -1 e eY (Y +M ) (Y -M ) Zee ee0 0 0 0
SaaSaeSeaSee
SaaSaeSeaSee
1
1( )( )( ) ( )
−
−
= − + ==
=
S E Y E YE+Y E-Y
Y Z Y Z0 0
(15) (16)
YaaYaeYeaYee
a -1 aY (E+M ) (E-M ) Yaa aa0 0a -1-2 Y (E+M ) Maa ae0
-1 aM (E+M ) Yea aa 0-1M -M (E+M ) Mee ea aa ae
(18)
YaaYaeYeaYee
1
1( )( )( ) ( )
−
−= − + == + −=
Y E S E SE S E S
Y Z Y Z0 0(17)
-1S -S (E+S ) Saa ae ee ea-1 eS (E+S ) Yae ee 0
e -1-2 Y (E+S ) See ea0e -1 eY (E+S ) (E-S ) Yee ee0 0 −
=
-1(E+Y ) (E-Y )aa aa-1 a-(E+Y ) Z Yaa ae0
a -12Y Z (E+Y )aaea 0a -1 aY Y Z (E+Y ) Z Yaaee ea ae0 0
a aY Z Y Zaa aa0 0
MaaMaeMeaMee
MaaMaeMeaMee
(19) (20)
![Page 10: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/10.jpg)
10
Mutual Conversion
S Y
M
![Page 11: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/11.jpg)
11
Reciprocity and Power ConservationParametersNetwork
Y S M
Reciprocal
Lossless
Reciprocal & Lossless
T
T
T
M = Maa aaM = -2Mea aeM = Mee ee
= S Sik ki
TS=S= Y Yik ki
TY = Y(21)
*M M = Eaa aa* *M = 2M Mea aa ae
*ReM = M Mee ae ae*
1
*N
S Sji jk ikjδ=∑
=
=S S EY =0Re ik
ReY=0(22)
* *1 1
* *N N
S S S Sji ijjk kj ikj jδ= =∑ ∑
= =
= =S S SS E =* *M M = M M Eaa aa aa aa* *M = 2M Mea aa ae
1 *M = M Mae aa ea2*ReM = M Mee ae ae
(23)= - *Y Yik ki
−Y = Y*
10
i kik i kδ
⎧⎪⎪⎪⎨⎪⎪⎪⎩= =
≠T matrix transposition, * Hermitian conjugation
![Page 12: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/12.jpg)
12
Matrix Properties (Reciprocal and Lossless Networks)
1. The admittance matrix Y is symmetric for reciprocal networks and purely imaginary for lossless networks.
2. The scattering matrix S is symmetric for reciprocal networks andunitary for lossless networks.
3. The dot product of any column/row of the scattering matrix S with aconjugate of a different column/row gives zero (orthogonality condition)for reciprocal and lossless networks.
4. The acoustic block Maa of the mixed scattering matrix M satisfies theunitary matrix property, with the acoustoelectric and electroacousticblocks Mae and Mea converted to each other.
![Page 13: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/13.jpg)
13
Reference Plane Transformation
a1
I1
V1 V 2
a 2I 2
bk
ak
V NV
kIkI N
N-port network[S], [Y], [M]
1 2
kN
ak 'b
k 'lk
b 2b
1
b Na N
Fig. 2. Shifting reference planes for an N-port network (outward)
![Page 14: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/14.jpg)
14
Reference Plane Transformation Equations
Type Matrix Scalar
Transformation
Wave scattering matrix
Mixed scattering matrix
1
2
0 00 0
0 0 N
j l
j l
j l
ee
e
β
β
β
−
−
−
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
=E
……
…
' E SES =
'aa aa aa aa'ae aa ae'ea ea aa'ee ee
M = E M EM = E MM =M EM =M
⎧⎪⎪⎪⎨⎪⎪⎪⎩
'
-1 '
A = EA
B = E B'
1 'k k k
k k k
a e ab e b−
⎧ =⎪⎪⎨⎪ =⎪⎩kj l
ke e β−=
( )' i kj l liik ik k ikS S e e S e β− += =
'
'
'
'
, ,
, ,, ,
, ,
iik ik k
iik ik
ik ik k
ik ik
i k mM M e eM M e i m k mM M e i m k mM M i m k m
≤== ≤ >= > ≤= > >
(24) (25)
(29)
(26)
(27)
(28)
![Page 15: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/15.jpg)
15
Transformation Law
1. The reference plane shift at the i-th and k-th ports changes the phase of the scattering matrix element Sik in accordance with theacoustic path change li+ lk for the incident and reflected wavestraveling throughout these ports.
2. It is only the elements of the mixed scattering matrix related to theacoustic ports which are subject to change due to reference planetransformation while elements referred to electrical ports remainunchanged.
3. Shifting the reference planes in the inward direction may beaccounting for by reversing the exponent sign in Eqs. (24-29).
![Page 16: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/16.jpg)
16
Part 2. SAW Transducer Mixed Scattering Matrix
![Page 17: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/17.jpg)
17
Mixed Port Representation of a SAW Transducer
1, 2 – acoustic ports, 3 – electric port
a1
b1
a2
b2
1 2
3VI
L
Fig. 3. Three-port representation of a SAW transducer
![Page 18: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/18.jpg)
18
Mixed Scattering Matrix of a SAW Transducer
Mixed scattering matrix of a SAW transducer
1 11 12 13 1
2 21 22 23 2
31 32 33
b m m m ab = m m m aI m m m V
⎡ ⎤⎡ ⎤ ⎡ ⎤⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎣ ⎦ ⎣ ⎦⎢ ⎥⎣ ⎦Block-matrix form
eeI M Vaa ae
ea
B M M AM
⎡ ⎤ ⎡ ⎤ ⎡ ⎤⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎣ ⎦ ⎣ ⎦ ⎣ ⎦=
where A=[a1 a2]T is the vector of the incident waves, B=[b1 b2]T is the vector of the reflected waves at the acoustic ports, I is the terminal current, V is the voltage applied to the transducer bus-bars at the electric port.
(30)
(31)
An ideal SAW transducer is a reciprocal and lossless three-portacoustoelectric network with two acoustic and one electric ports.
![Page 19: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/19.jpg)
19
Physical Meaning of Matrix BlocksNotation Block Type Meaning Mode
Maa AcousticScattering coeffcients of a short-circuit SAW transducer
Passivegrating,
V=0
Mae AcoustoelectricAcoustoelectricconversion by a SAW transducer with the voltage V applied to the transducer bus-bars
SAW excitation,
V≠0
Mea ElectroacousticTerminal short-circuit current induced by the incident acoustic waves
SAW detection,
V=0
Mee ElectricTransducer admittance seen at the electric port when there are no incident waves at the acoustic ports
One-portelectricalnetwork
V≠0
11 12
21 22
m mm m⎡ ⎤⎢ ⎥⎢ ⎥⎣ ⎦
[ ]T13 23m m
[ ]31 32m m
33m
![Page 20: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/20.jpg)
20
Mixed Scattering Matrix Elements
Element Definition Mode Meaning Units
m11 b1/a1Short-circuit,V=0, a2=0
Reflection coefficient of the short-circuit transducer at the left acoustic port 1
-
m22 b2/a2Short-circuit,V=0, a1=0
Reflection coefficient of the short-circuit transducer at the right acoustic port 2
-
m12 b1/a2Short-circuit,V=0, a1=0
Transmission coefficient of the short-circuit transducer in the left direction
-
m21 b2/a1Short-circuit,V=0, a2=0
Transmission coefficient of the short-circuit transducer in the right direction
-
![Page 21: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/21.jpg)
21
Mixed Scattering Matrix Elements (Cont’d)
Element Definition Mode Meaning Units
m13 b1/V SAW excitation,a1=a2=0, V≠0
Acoustoelectric conversionfunction, left direction (port 1)
m23 b2/V SAW excitation,a1=a2=0, V≠0
Acoustoelectric conversion function, right direction (port 2)
m31 I/a1SAW detection,
short-circuit,a2=0, V=0
Electroacoustic conversion function from the left direction (current induced by the wave a1=1 at the left acoustic port 1)
m32 I/a2SAW detection,
short-circuit,a1=0, V=0
Electroacoustic conversion function from the right direction (current induced by the wave a2=1 at right acoustic port 2)
m33 I/V One-port electrical network,
a1=a2=0, V≠0
Transducer admittance at the electric port
Ω-1
1/ Ω
1/ Ω
1/ Ω
1/ Ω
![Page 22: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/22.jpg)
22
Conversion of the Mixed Scattering Matrix to the Wave Scattering Matrix
00 0
0 00 0
2ae eaaa ae
ea
YY Y Y Y
Y Y YY Y Y Y
aa aeea ee
M MM MS SS = S S
M
⎡ ⎤⎢ ⎥⎢ ⎥⎡ ⎤ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎣ ⎦ ⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
− + +=
−− + +or in the scalar form
2 0 1313 31 13 3211 12
0 0 02 0 2323 31 23 32
21 220 0 0
0 31 0 32 00 0 0
Y mm m m mm m
Y Y Y Y Y Y
Y mm m m mm m
Y Y Y Y Y Y
Y m Y m Y YY Y Y Y Y Y
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
− −+ + +
= − −+ + +
−− −
+ + +
S
where Y0 =1/Z0 is the characteristic admittance at the electric port, Y=m33 is the transducer admittance.
Scattering matrix of a SAW transducer
(32)
(33)
![Page 23: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/23.jpg)
23
Lossless Condition
* * * *
* * * * 1aa ae aa ae aa aa ae ae aa ea ae ee
ea ee ea ee ea aa ee ae ea ea ee ee
⎡ ⎤ ⎡ ⎤⎡ ⎤ ⎡ ⎤⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥
⎣ ⎦ ⎣ ⎦ ⎢ ⎥ ⎣ ⎦⎣ ⎦
∗
= + += =+ + T
E 0S S S S S S S S S S S SSS*S S S S 0S S S S S S S S
or
aa aa ae aeaa ea ae eeea ea ee ee
⎧⎪⎪⎪⎨⎪⎪⎪⎩
* ** ** *
S S +S S = ES S +S S = 0S S +S S =1
(34)
(35)
For a lossless SAW transducer the wave scattering matrix S is unitary.
![Page 24: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/24.jpg)
24
Properties of Reciprocal and Lossless SAW TransducerEquationProperty
Matrix Scalarm12= m21
m31=-2 m13
m32=-2 m23
Reciprocity
|m |2 +|m |2=1
m11 m12* + m22*m21=0
11 12
|m22|2 +|m21|2=1
m13=-( m23*+ m22* m23) /m21*m23=-( m13*+ m11* m13) /m12*Rem33=|m13|2 +|m23|2
Causality
Power conservation
aa aaTM M=
2ea aeTM M=−
*aa aa =M M E
*12ae aa eaM M M=
*33 ae aeRe m M M=
Re Im H=ee eeM M'
'3333 '
( )1 Re mIm m dω ωπ ω ω
∞
−∞=
−∫2
11 22 12 21 12 11 11 12, 1 , 2m m m m m m πθ θ= = ⇒ = − = ±Particular Case: (42)
![Page 25: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/25.jpg)
25
Summary of SAW Transducer Properties
1. The mixed scattering matrix M of a SAW transducer contains threeindependent elements m11, m13 , m33 to be determined, in general case.
2. The transmission coefficient m12 can be deduced from the reflectioncoefficient m11 using Eq. (41). The coefficients m11 and m12 are in thephase quadrature, with the phase ambiguity of π in general case.
3. Given the acoustoelectric conversion function m13 and the scatteringcoefficients m11 and m12, the electroacoustic function m23 can be foundby Eq. (39).
4. The electroacoustic conversion functions m31 and m32 can be found byreciprocity using Eqs. (37).
5. The real part (radiation conductance) G(w) of the transducer admittanceY(w)=G(w)+jB(w)+ jw C can be found from the power conservation low Eq. (40).
6. The imaginary part (radiation susceptance) B(w) can be found by theHilbert transformation of G(w) (the causality principle).
7. The transducer static capacitance C should be found from the solutionof the electrostatic problem in the closed-form or numerically.
![Page 26: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/26.jpg)
26
Mixed Scattering and Transmission Matrices
The mixed transmission matrix T=[tik], i,k=1,2,3 describes the relationship of the acoustic waves a1, b1 at the left acoustic port 1 (as input) and the terminal current I with the waves a2, b2 at the right acoustic port 2 (as output) and the transducer bus-bar voltage V
11 12 13
21 22 23
31 32 33
1 2
1 2
a t t t ab t t t bI t t t V
⎡ ⎤ ⎡ ⎤⎡ ⎤⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎣ ⎦⎣ ⎦ ⎣ ⎦
= (43)
Why Transmission Matrix?
The mixed transmission matrix T is appropriate for cascading SAWelements as it relates the waves at the input and output acoustic ports.
![Page 27: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/27.jpg)
27
Conversion between Scattering and Transmission
Scattering S Transmission T
S
T
11 12 13
21 22 23
31 32 33
m m mm m mm m m
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
2322
21 21 21
11 2311 11 2212 13
21 21 21
31 22 31 31 2332 33
21 21 21
1 mmm m m
m mm m mm mm m mm m m m mm mm m m
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
− −
− −
− −
21 1321 12 2122 23
11 11 11
1312
11 11 11
31 12 31 13 3132 33
11 11 11
1
t tt t tt tt t t
ttt t tt t t t tt tt t t
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
− −
− −
− −
11 12 13
21 22 23
31 32 33
t t tt t tt t t
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
![Page 28: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/28.jpg)
28
Part 3. SAW Filter Simulation
![Page 29: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/29.jpg)
29
SAW Filter Representation
A1
B1
A2
B2
a1
b1
V1 V2
I1 I2
M1 M21 2
3 4
L
5a)
Fig. 4. Multi-port SAW filter representation in terms of:a) mixed scattering matrices (M-matrices),b) mixed transmission matrices (T-matrices)
A1
B1
A2
B2
a1
b1
V1 V2
I1 I2
T1
T2
3 4
1 2
L
5b)
![Page 30: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/30.jpg)
30
Cascading Mixed Scattering Matrices
1 1 111 12 131 11 1 1
1 21 22 23 11 1 11 131 32 33
m m mB Ab m m m aI Vm m m
⎡ ⎤⎡ ⎤ ⎡ ⎤⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎣ ⎦⎢ ⎥⎣ ⎦ ⎣ ⎦
=
Mixed scattering matrix for each transducer
2 2 211 12 131 12 2 2
2 21 22 23 22 2 22 231 32 33
m m ma bB m m m AI Vm m m
⎡ ⎤ ⎡ ⎤⎡ ⎤ ⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎢ ⎥⎣ ⎦ ⎣ ⎦⎢ ⎥⎣ ⎦
=
(44)
(45)
Input:
Output:
![Page 31: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/31.jpg)
31
Overall Mixed Scattering Matrice
Total acoustoelectric system (SAW filter), no acoustic coupling conditions imposed
1 1 111 13 12
2 2 222 23 21
1 1 131 33 32
2 2 232 33 312 2 212 13 11
1 1 121 23 22
1 1
2 2
1 1
2 2
1 1
1 1
0 0 00 0 0
0 0 00 0 00 0 0
0 0 0
m m mm m m
m m mm m mm m m
m m m
B AB AI VI Va ab b
⎡ ⎤ ⎡ ⎤⎡ ⎤⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎣ ⎦ ⎣ ⎦⎣ ⎦
= (46)
Block-matrix form3
2 3
3 32 33
⎡ ⎤⎡ ⎤ ⎡ ⎤⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥
⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎣ ⎦ ⎣ ⎦ ⎣ ⎦
=11 12 1
21 2 2
1
B M M M AI M M M VC M M M C
(47)
![Page 32: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/32.jpg)
32
Nomenclature
A=[A1 A2]T vector of the incident waves at the external acousticports 1, 2
B=[B1 B2]T vector of the reflected waves at the external acousticports 1, 2
C=[a1 b1]T vector of the traveling waves at the internal(coupled) acoustic ports 5
I =[I1 I2]T vector of the currents at the electric ports 3, 4V =[V1 V2]T vector of the voltages at the electric ports 3, 4
![Page 33: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/33.jpg)
33
General SolutionBy excluding the unknown vector C we find the following solution of the matrix system of equations (47)
⎡ ⎤ ⎡ ⎤⎡ ⎤⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎣ ⎦ ⎣ ⎦⎣ ⎦
= aa ae
ea ee
M MB AM MI V
where the mixed scattering matrix of a SAW filter ⎡ ⎤⎡ ⎤⎡ ⎤
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥ ⎣ ⎦⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦ ⎣ ⎦ ⎣ ⎦
13 -111 12aa ae33 31 32
ea ee 21 22 23=
MM MM MM = + (E-M ) M MM M M M M
(48)
(49)
11 11311 12
22 22322 21
1 1 131 33 32
2 2 232 33 31
22 21312 11
11 12321 22
00 0, ,
00 0
0 0 0, ,
0 0 0
00 0, ,
00 0
mm mmm m
m m mm m m
mm mmm m
⎡ ⎤⎡ ⎤ ⎡ ⎤⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎣ ⎦ ⎣ ⎦⎣ ⎦
⎡ ⎤ ⎡ ⎤ ⎡ ⎤⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥ ⎢ ⎥⎣ ⎦ ⎣ ⎦ ⎣ ⎦
⎡ ⎤⎡ ⎤ ⎡⎢ ⎥⎢ ⎥ ⎢⎢ ⎥⎢ ⎥ ⎢⎣ ⎦ ⎣⎣ ⎦
= = =
= = =
= = =
11 12 13
21 22 23
31 32 33
M M M
M M M
M M M⎤⎥⎥⎦
![Page 34: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/34.jpg)
34
Particular Case: Isolated Acoustoelectric System
There are no incident waves at the external acoustic ports * (A=0, electrical two-port)
I = YV
1M
=
∆+
ee-1
22 23 33 32
22 23 33 32
Y = M = M +M (E-M ) M
M + M (E M )M
(50)
where a system admittance matrix
2 111 22
1 2 1 1 1 233 11 32 23 32 13
1 2 2 1 2 223 31 33 22 31 13
,
1 1
1 1
1
m m m m m mM Mm m m m m mM M
M m m
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
+ ∆ ∆=+∆ ∆
∆ = −
Y (52)
(51)
![Page 35: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/35.jpg)
35
Reflectionless SAW Transducer: Quasi-Static Approximation
In the quasi-static approximation (reflectionless SAW transducer)
Therefore,
(53)
1,2 1,211 22 0.m m= =
1 1 2 1 1 233 32 13 33 23 13
1 2 2 1 2 223 31 33 23 13 33
22
m m m m m mm m m m m m
⎡ ⎤ ⎡ ⎤⎢ ⎥ ⎢ ⎥=⎢ ⎥ ⎢ ⎥⎢ ⎥ ⎢ ⎥⎣ ⎦ ⎣ ⎦
−=
−Y
In the quasi-static approximation (reflectionless SAW transducers), the self-admittances Y11, Y22 are defined by the admittance of the inputand output SAW transducers, with the cross-admittance Y12= Y21 givenby the product of the acoustoelectric functions of both transducers.
![Page 36: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/36.jpg)
36
Cascading Mixed Transmission Matrices
Augmented transmission matrices of SAW transducers:
(54)
2 2 21 11 12 13 2
2 2 221 21 22 23
112 2 2 22 31 32 33
00
0 0 1 00
a t t t ABb t t tVVVI t t t
⎡ ⎤⎡ ⎤ ⎡ ⎤⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎣ ⎦⎣ ⎦ ⎢ ⎥⎣ ⎦
=
1 1 1111 12 131
1 1 11 121 22 23
1 1 11 131 32 332 2
000
0 0 0 1
at t tAB bt t tI Vt t tI I
⎡ ⎤ ⎡ ⎤⎡ ⎤⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎣ ⎦ ⎣ ⎦⎢ ⎥⎣ ⎦
=
(55)
Input: Output:
1,21,2
1,2 1,2 1,21,2 1,2 1,211 12 13 1,2 1,21,2 1,2 1,2
1,2 1,21,2 1,2 1,221 22 23 1,2 1,21,2 1,2 1,231 32 33 1,2 1,2 1,2
1,2 1,21,2 1,2
2322
21 21 21
11 2311 11 2212 13
2121 21
31 22 3132 33
21 21
1
t t tt t tt t t
mmm m m
m mm m mm mmm m
m m mm mm m
⎡ ⎤⎢ ⎥ =⎢ ⎥⎢ ⎥⎣ ⎦
− −
− −
−1,2 1,2
1,231 23
21
m mm
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
−
where
![Page 37: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/37.jpg)
37
Overall Mixed Transmission Matrix
1 2 1 2 1 2 1 2 1 1 2 1 211 11 12 21 11 12 12 22 13 11 13 12 23
11 12 1 2 1 2 1 2 1 2 1 1 2 1 221 11 22 21 21 12 22 22 23 21 13 22 23
21 22 1 2 1 2 1 2 1 2 1 1 231 11 32 21 31 12 32 22 33 31 13
t t t t t t t t t t t t tT T
t t t t t t t t t t t t tT T
t t t t t t t t t t t t
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
+ + +
+ + += =
+ + +
13
23
31 32 33
T
T T
T T T1 232 23
2 2 231 32 330
t
t t t
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
The overall mixed transmission matrix is given by the product ofthe augmented mixed transmission matrices
11 121 2
1 21 22 2
1 3
T TA AB T T B
⎡ ⎤⎡ ⎤ ⎡ ⎤⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎢ ⎥⎢ ⎥ ⎢ ⎥⎣ ⎦ ⎣ ⎦⎣ ⎦
=13
23
3 32 3
TT
I VT T T(56)
Block-matrix form
(57)
![Page 38: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/38.jpg)
38
Particular Case: Isolated Acoustoelectric System
There are no incident waves at the external acoustic ports * (A1=B2=0, electrical two-port)
(58)111T −= −33 31 13Y T T T
Substitution of Eqs. (55), (57) into Rq. (58) gives the same result (52).
![Page 39: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/39.jpg)
39
Brief Summary on Cascading Techniques
1. Two basic techniques for SAW transducer cascading are: direct interconnection of the mixed scattering matricescascading the mixed transmission matrices.
2. Both techniques give the identical results.
3. Cascading techniques can be generalized to the case of N SAWtransducers following similar guidelines as in the particular caseof two in-line SAW transducers.
![Page 40: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/40.jpg)
40
SAW Filter S-ParametersOnce two-port admittance matrix (Y-parameters) in the form of (51) or (58) has been determined, the scattering matrix S (S-parameters) can be found by using the matrix equation
1( ) ( ) −= 0 0S Y - Y Y + Y
0 1 1 0 2 2 1 2 2 1 1 2 0
2 1 0 0 1 1 0 2 2 1 2 2 1
( ) ( ) 212 ( ) ( )
Y Y Y Y Y Y Y YY Y Y Y Y Y Y Y Y
⎡ ⎤⎢ ⎥⎢ ⎥⎣ ⎦
− + + −= ∆ − + − +S
0
0
00
YY
⎡ ⎤⎢ ⎥⎣ ⎦
=0Y where Y0=1/Z0 is characteristic admittance (typically, Z0=50 Ω)
Closed-form S-parameters
(59)
0 1 1 0 2 2 1 2 2 1( ) ( )Y Y Y Y Y Y Y∆ + + −=The denominator ∆Y accounts for the multiple reflections due to the regenerated signal (triple transit echo (TTE)) between the input and output SAW transducers loaded by the characteristic admittance Y0 at each end.
(60)
![Page 41: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/41.jpg)
41
Particular Case: High-Loss SAW Filter
Assumptions: Y11 << Y0, Y22 << Y0, and Y12Y21 << Y02
(61)1 2 1 20 23 13 23 13
122 4120
YS Z m m m m
Y= − = ∼
1. In general case, the SAW filter transfer function S12 is no longer proportional to the cross-admittance Y12 and therefore it has morecomplicated frequency behavior rather than just the product of theacoustoelectronic functions of the input and output SAWtransducers (an idealized SAW filter frequency response).
2. This frequency response distortion must be accounted andcompensated for at the SAW filter synthesis step.
![Page 42: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/42.jpg)
42
Part 4. SAW Transducer Modeling in Quasi-Static Approximation
![Page 43: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/43.jpg)
43
Mixed Scattering Matrix
Basic Assumption: A short-circuit SAW transducer is reflectionless, i.e. m11= m22=0.
Practicality: Valid if the central frequency f0 of a SAW transducer is faraway from the synchronous frequency fp=v/2p where v is SAW velocity and p is the transducer period (pitch).
In the quasi-static approximation the mixed scattering matrix of a SAW transducer
,*
*
00
2 2L Np
j
j
j
e me m em m e Y
β β
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
Φ = =
− Φ
−Φ − Φ
− Φ= −
−M
m=m13 acoustoelectric functionL=Np total acoustical length of a SAW transducer (port-to-port)β=ω/v SAW wave number
(62)
![Page 44: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/44.jpg)
44
Mixed Transmission Matrix
In the quasi-static approximation the mixed transmission matrix of a SAW transducer
m=m13 acoustoelectric functionL=Np total acoustical length of a SAW transducer (port-to-port)
β=ω/v SAW wave number
(63)
*
*33
00
2 2 Im
j
j
j j
e me m
me m e m
Φ
− Φ
Φ − Φ
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
=−
T
Φ=βL total phase lag
![Page 45: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/45.jpg)
45
Phase Reference
The mixed scattering and transmission matrices take the simplestform when the phase is referenced to the transducer center (F=0):
(63)
*
*
1 00 12 2 Im
mm
m m Y
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
=−
T
*
*
0 11 02 2
mm
m m Y
⎡ ⎤⎢ ⎥⎢ ⎥⎢ ⎥⎢ ⎥⎣ ⎦
= −−
M
(64)
The independent matrix elements are m and Y to be determined in thequasi-static approximation.
![Page 46: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/46.jpg)
46
SAW Transducer ParametersSAW Transducer Parameters
In the quasi-static approximation, the mixed scattering matrix of a SAW transducer is characterized by three independent parameters:
1) effective SAW velocity v2) acoustoelectric conversion (transfer) function m3) transducer admittance Y=G+jB+jωC where C is the
transducer static capacitance
The acoustic conductance G and susceptance B are interrelated viathe Hilbert transform due to the causality principle.
![Page 47: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/47.jpg)
47
Periodic SAW Transducer
1V0 V1 VN-1
ap
L=Np
…a1
b1
a2
b2
2
Fig. 5. Cross-section view of the finite length periodic SAW transducer
![Page 48: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/48.jpg)
48
Acoustoelectric Conversion FunctionThe acoustoelectric conversion (transfer) function of a SAW transducer
2
1
0a
bmV =
=
where b1 is the generalized SAW amplitude of the wave traveling in the left direction, V is the voltage applied across the transducer.
* * *0
1 1 12 2 4
WP aa Y ωφφ φφ= = =Γ
generalized SAW amplitudef surface potential accompanying a SAW of the amplitude aY0=ω W/2Γ acoustic characteristic admittance (after D.P.Morgan)Γ=K2/2ε substrate material constantK2 piezoelectric coupling factorε=ε0+εp surface effective permittivityε0 permittivity of the medium above the substrateεp effective permittivity of the substrate
0a Y φ=
SAW power flow carried by the uniform acoustic beam of the width W
(65)
(66)
![Page 49: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/49.jpg)
49
Closed-Form Equation (D.P.Morgan)
In the quasi-static approximation (D. P. Morgan), a potential φ of the surface acoustic wave launched by a periodic SAW transducer in the left direction is
/ 2( ) ( ) ( ) j Lj V F e βφ β ε ξ β β −= Γ
β=ω/v SAW wave numberξ(β) element factor F(β) array factorL=Np transducer lengthN number of electrodes (fingers) p finger pitch (period).
(67)
An element factor ξ(ω) characterizes frequency behavior of the acoustic sources and depends on the metallization ratio.An array factor F(ω) accounts for SAW filter selectivity and related with the finger polarity sequence by the Fourier transform.
![Page 50: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/50.jpg)
50
Element Factor
2sin( ) (cos )( cos ) nP
P ν
πνξ ν−
= ∆− ∆
ν=ϕ/2π-n normalized frequency variable (base band)ϕ=βp phase lag per period pn=[ϕ/2π] space harmonic number (n ≤ ϕ/2π ≤ n+1)Pn(-cos∆) Legendre polynomialP-ν(-cos∆) Legendre function∆=πη dimensionless variable related to the electrode geometryη=a/p metallization ratio (duty factor)a finger width.
In the quasi-static approximation, the element factor can be found from the electrostatic solution for the periodic strip array and takes the form
(68)
To the first order ξ(ν)~sinπν.
![Page 51: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/51.jpg)
51
Array Factor
1( )2 2
1 11( )20 0
1 1( )kN NN jj k
k kk k
F V e V eV Vϕϕϕ
Φ+ −− −− −− −
= === ∑ ∑ (69)
Φ=βL= Nj is the total phase lag throughout the transducer, V is the voltage between transducer bus-bars. The phase in Eq. (69) is referenced to the transducer center.
The array factor F(ϕ) is given by the Fourier transform of a set of the electrode potentials Vk, k=0,N-1:
Acoustoelectric Function
/20 2 ( ) ( )2j
VY jam WK F eVφ
ω εξ ϕ ϕ − Φ== =
In the quasi-static approximation the acoustoelectric function
(70)
Fourier Transform Relation
![Page 52: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/52.jpg)
52
Unapodized Periodic SAW Transducers
Fig. 6. Charge distribution in the finite length periodic SAW transducer
![Page 53: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/53.jpg)
53
Basic Structure and Guard Electrodes
Fig. 7. Cross-section view of the periodic SAW transducer with guard electrodes
V0 V1 VN-1
…
1 2
VN-1 VN-1
…V0V0
…
basicstructure
k=0, 1, …, N-1
right guardelectrodes
k>N-1
left guardelectrodes
k<0
0 1 … N-1 N N+1 …-1-2…
Guard electrodes are introduced in the finite length SAW transducer tosuppress electrostatic end effects.
![Page 54: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/54.jpg)
54
Contribution of Guard Electrodes to Acoustoelectric Conversion (Particular Case)
Potentials on the guard electrodes
Particular case: all equipotential (grounded) guard fingers V0=VN-1=01
0
1 1( )N
jk jkk k
k kF V e V eV V
ϕ ϕϕ∞ −
− −
= −∞ === ∑ ∑
The finite summation in Eq. (71) gives the correct result for the infinite structure including guard electrodes contribution.
0
1
, 0, 1k
N
V kV
V k N−
⎧ <⎪⎪= ⎨⎪ > −⎪⎩(70)
(71)
left guard electrodesright guard electrodes
![Page 55: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/55.jpg)
55
Contribution of Guard Electrodes to Acoustoelectric Conversion (General Case)
General case: Non-equipotential guard electrodes at the ends V0πVN-1
1 1
0 10
1 11 0 1 0
10 0
( ) ( ) ( )
( )1 1
Njk jk jk jk
k k Nk k k k N
jNN Njk jkN N
k k Nj jk k
left guard basic right guard
V e V e V e V e
V e V V VV e V V e
e e
ϕ ϕ ϕ ϕ
ϕϕ ϕ
ϕ ϕ
∞ − − ∞− − − −
−=−∞ =−∞ = =
−− −− −− −
−− −= =
= + + =
− −= + = − +
− −
∑ ∑ ∑ ∑
∑ ∑where the following identities have been used
1 1
0 0 0
1 1, lim1 1
jNN Njk jk jk
j jNk k k
ee e ee e
ϕϕ ϕ ϕ
ϕ ϕ
±− ∞ −± ± ±
± ±→∞= = =
−= = =− −∑ ∑ ∑
(72)
101
10
1( ) ( )1
Njk N
jk Nk
V VF V V e
V eϕ
ϕϕ−
− −−−
=
⎧ ⎫⎪ ⎪⎪ ⎪⎪ ⎪⎪ ⎪⎨ ⎬⎪ ⎪⎪ ⎪⎪ ⎪⎪ ⎪⎩ ⎭
−= − +
−∑ (73)
In the particular case of the grounded guard fingers V0=VN-1=0, Eq. (73) reduces to Eq. (71).
![Page 56: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/56.jpg)
56
Finger and Gap Taps
The sum in Eq. (73) can be transformed to another formϕϕ ϕ ϕ
ϕ ϕ
⎛ ⎞∞ − −⎟⎜ − +⎟⎜− − − + ⎟⎜ ⎟⎜ ⎟− ⎜ ⎟⎜ ⎟⎟⎜=−∞ = = =⎝ ⎠= − = ∆
−∑ ∑ ∑ ∑11 1 ( )( ) 2
1 0 0
1 12 sin /21
N N M j kjk jk j k 1k k k kj
k k k kV e V e V e V eje
(74)
where ∆Vk= Vk+1- Vk is the voltage in the k-th gap between two adjacent fingers having the potentials Vk+1 and Vk, respectively, M=N-1 is number of the gaps in the basic sructure.
As the last gap voltage in Eq. (74) ∆VN-1=VN-VN-1=0, the summation corresponds to the number of gaps M in the basic structure. The factor e-jϕ/2 accounts for the gap position offset with respect to the finger center.
According to Eq. (74), the array factor can be alternatively expressed in terms of the Fourier transform of the gap voltages ∆Vk that gives zero contribution of the guard fingers to the overall response regardless a set of the potentials Vk.
![Page 57: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/57.jpg)
57
Finger and Gap Taps Properties
1. Finger taps are located in the electrode centers, with amplitudes proportional to the electrode potentials Vk.
2. Gap taps are attributed to the interelectrode gaps, with amplitudes proportional to the gap voltages DVk= Vk+1- Vk.
3. Using the voltages ∆Vk instead of the potentials Vk excludes implicitly a uniform potential applied across the transducer.
4. Both finger and gap taps give exactly the same results if applied correctly. However, a special care must be taken while using in modeling finger taps.
![Page 58: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/58.jpg)
58
Acoustoelectric Function (Gap Taps)
The sum in Eq. (73) can be transformed to another form
where the gap element factor ζ(ϕ)
( ) (cos )( ) , /2 .2sin /2 ( cos )nP
Pν
ξ ϕζ ϕ ν ϕ πϕ −
∆= = =− ∆
(76)
and the gap array factor(77)
/ 221 ( ) ( )2jm WK F eω εζ ϕ ϕ − Φ= ∆
(74)
1 1( )20
( ) 2 sin / 2 ( )M j k
kk
F j F V e ϕϕ ϕ ϕ− − +
== = ∆∑
The acoustoelectric conversion function in terms of gap voltages
1 1 1( )( ) 21 0 0
1 12 sin / 21
N N M j kjk jk j k 1k k k kj
k k k kV e V e V e V eje
ϕϕ ϕ ϕϕ ϕ
⎛ ⎞∞ − −⎟⎜ − +⎟⎜− − − + ⎟⎜ ⎟⎜ ⎟− ⎜ ⎟⎜ ⎟⎜ ⎟=−∞ = = =⎝ ⎠= − = ∆
−∑ ∑ ∑ ∑
(75)
![Page 59: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/59.jpg)
59
Element Factor Properties
Fig. 7. Normalized element factor at first five space harmonicsfor different metallization ratios:
- - -h=0.25, — h= 0.5, − - − h= 0.75
0 1 2 3 4 5-1
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
1.2
Normalized frequency ν = f/2f0
Nor
mal
ized
am
plitu
de ζ
( ν)
0 1 2 3 4 5-1
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
1.2
Normalized frequency ν = f/2f0
Nor
mal
ized
am
plitu
de ξ
( ν)
a) finger element factor x(n) b) gap element factor z (n)
![Page 60: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/60.jpg)
60
Misusing Finger Taps
1 1 1( ) 2
00 0, .
sin ( )2( ) ( 1) 1sin ( )2
N N Njjk jkk
k k
NfF e e e f
ϕϕ ϕ πϕ π
ϕ ϕ πϕ π
− − −−− − −
= =
−= − = = =
−∑ ∑
What is the passband width of the solid (unsplit) finger unapodized SAW transducer with the number of fingers N and the central frequency f0 ?
0 .22 , where fF f f N∆ = ∆ ∆ =
In terms of the finger taps Vk=(-1)k, the frequency response
The main lobe (pass band) width
Problem:
Solution 1 (wrong):
In terms of the gap taps, we can find the correct result as0 0 .
2 22 , where 1f fF f f M N=∆ = ∆ ∆ =
−
Solution 2 (correct):
i.e. the main lobe width is proportional to 1/M > 1/N where M=N-1 is the number of gaps in the transducer.
![Page 61: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/61.jpg)
61
Merits of Gap Taps Against Finger Taps
1. Both models are theoretically equivalent if correctly applied. However, in general case the finger taps model is awkward to account for a contribution of the guard electrodes to the overall frequency response requiring more sophisticated equations.
2. Contrary to finger taps, the gap taps model gives identically a zero contribution of the guard electrodes to the overall response, regardless a set of the potentials Vk in the basic structure.
3. The gap taps model comprises the finite summation over the gaps in the basic structure, with the total number of gaps M=N-1.
4. Since we use the gap voltages ∆Vk instead of the potentials Vk, this excludes any uniform potential applied across the transducer while in the finger taps model this uniform potential must be implicitlytaken into consideration and included into equations.
![Page 62: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/62.jpg)
62
Merits of Gap Taps Against Finger Taps (Cont’d)
5. Some textbooks refer to wrong equations in terms of the of the finger taps model which are valid in the particular cases only.
6. The gap element factor has the simpler shape and weaker (flatter) frequency dependence if compared to the finger element factor.
7. It is highly recommended to use the gap taps model rather than thefinger taps model wherever possible as misusing the finger tapsmodel may cause troubleshooting in SAW filter simulation, inparticular, for wideband SAW filters.
![Page 63: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/63.jpg)
63
Apodized Periodic SAW Transducers
yi
yk+1
yi-1
+∆V/2
-∆V/2
i-1 i k k+1
yk
y=0∆yi ∆yk
y
Fig. 8. Finger and gap tap weights of the apodized SAW transducer
Wdy
![Page 64: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/64.jpg)
64
Basic Assumptions
1. The propagating wavefront launched by an apodized SAW transducer isintercepted by the uniform receiving SAW transducer or multistrip coupler.
2. Each electrode is connected to either of two parallel bus-bars and complemented by a dummy finger for the wave front equalization.
3. Transversal electrostatic end effects are neglected.4. The diffraction and beam steering effects are ignored.
/2
/2
1( ) ( , )W
W
x x y dyWφ φ−
= ∫ (78)
A detected signal is not affected if the actual two-dimensional distribution φ(x,y) of the surface wave potential is replaced by the averaged distribution over the acoustic aperture W.
![Page 65: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/65.jpg)
65
Generalization of Finger Taps
Fourier transform of Eq. (78) gives
In terms of the finger taps the averaged array factor
(79)/2
/2
/2
1( ) ( , ) ( ) ( )W
j L
Wy dy j V F eW
βφ β φ β ε ξ β β −
−= =∫
1/ 2 1 ( )2
0/ 2
1 1( ) ( , )NW N j k
kkW
F F y dy V eW V
ϕϕ ϕ
−− − −
=−
= =∆ ∑∫ (80)
The mean potential averaged across the aperture W can be found as/2 /2
/2 /2
1 1 1( ) ( ) ( )k
k
yW Wkk k k k
yW W
yV V y dy V y dy V y dy VW W W W− −
= = + = − ∆∫ ∫ ∫ (81)
where ∆V is the voltage applied to the transducer bus-bars.
kVTo determine the averaged potentials across the aperture W, we consider a structure with a set of finger potentials Vk=±∆V/2.
![Page 66: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/66.jpg)
66
Generalization of Gap TapsFrom Eq. (81) the mean gap voltage is given by
1k
k k kyV V V V
W+
∆∆ = − = − ∆ (82)
where ∆yk= yk+1- yk is the overlap of the adjacent fingers with the transversal gap positions yk+1 and yk, respectively.
1. The effective finger and gap taps and are essentially fractions of the bus-bar voltage ∆V weighted by the normalized transversal gappositions yk /W or finger overlaps ∆yk /W, respectively.
kV kV∆
kV kV∆
2. For apodized SAW transducers, the acoustoelectric conversion
function can be found in terms of the effective tap weights and
replacing the conventional potentials Vk or gap voltages ∆Vk.
![Page 67: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/67.jpg)
67
Example of SAW Filter Simulation
Specifications
Central frequency f0 70 MHzPass band width at -3 dB 9.4 MHzPass band width at -40 dB 10.6 MHzShape factor (-40/-3 dB) 1.13Pass band ripple (peak-to-peak) 0.5 dBStop band attenuation -50 dBInsertion loss (matched) 25 dB
![Page 68: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/68.jpg)
68
Example of SAW Filter Simulation
Design Parameters
Synchronous frequency fp=2f 0
Number of fingers per wave length 4 (split fingers)Number of fingers (unapodized IDT) 48Number of fingers (apodized IDT) 700Acoustic aperture 2.5 mm (≈53 λ)Substrate material 112o LiTaO3Die size 11.9 x 3.1 mm
![Page 69: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/69.jpg)
69
Frequency Response
50 55 60 65 70 75 80 85 90-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
Frequency, MHz
Log
mag
nitu
de, d
BF1(ω)
F2(ω)F(ω)
Fig. 9. SAW filter ideal frequency response:F1(ω) – input, F2(ω) – output, F(ω) =F1(ω) F2(ω) - SAW filter
![Page 70: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/70.jpg)
70
Time Response
Fig. 10. SAW filter ideal impulse response
0 0.5 1 1.5 2 2.5 3 3.5 4-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
Time, µsec
Tim
e R
espo
nse,
dB
Delay = 1.685 µsec
![Page 71: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/71.jpg)
71
Input/Output Admittance
Fig. 11. SAW filter admittance Y1,2(ω)=G1,2(ω)+jB1,2(ω): 1 - input, 2 - output
50 55 60 65 70 75 80 85 900
0.5
1
1.5
2
2.5
3
3.5x 10
-3
Frequency, MHz
Con
duct
ance
G1, G
2, mhO
G1 G
2
50 55 60 65 70 75 80 85 900
0.005
0.01
0.015
0.02
0.025
Frequency, MHz
Sus
cept
ance
B1, B
2, mhO
< si070v1_1.s >
B2
B1
a) conductance b) susceptance
![Page 72: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/72.jpg)
72
S-Parameters (Unmatched)
Fig. 12. SAW filter S-parameters (unmatched)
50 55 60 65 70 75 80 85 90-1.5
-1
-0.5
0
Frequency, MHz
Log
Mag
nitu
de S
11, S
22, d
B
|S11|
|S22|
50 55 60 65 70 75 80 85 90-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
Frequency, MHz
Log
mag
nitu
de |S
12|,
dB
Insertion Loss = -31.50 dB
a) reflection coefficient S11, S22 b) transmission coefficient S12= S21
![Page 73: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/73.jpg)
73
S-Parameters (Matched)
Fig. 13. SAW filter S-parameters (matched)
a) reflection coefficient S11, S22 b) transmission coefficient S12= S21
50 55 60 65 70 75 80 85 90-4
-3.5
-3
-2.5
-2
-1.5
-1
-0.5
0
Frequency, MHz
Log
Mag
nitu
de S
11, S
22, d
B
< si070v1_1.ms >
|S11
|
|S22
|
50 55 60 65 70 75 80 85 90-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
Frequency, MHz
Log
mag
nitu
de |S
12|,
dB
Insertion Loss = -24.8 dB
![Page 74: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/74.jpg)
74
Pass Band Response
Fig. 14. SAW filter passband response without distortion compensation: 1 – ideal, 2 – unmatched, 3 - matched
65 66 67 68 69 70 71 72 73 74 75-5
-4.5
-4
-3.5
-3
-2.5
-2
-1.5
-1
-0.5
0
Frequency, MHz
Log
mag
nitu
de |S
12|,
dB
< si070v1_1.ms > : Insertion Loss = -25.53 dB
1
32
65 66 67 68 69 70 71 72 73 74 75-10
-8
-6
-4
-2
0
2
4
6
8
10
Frequency, MHz
Pha
se, d
egs
3
2
1
a) magnitude b) phase
![Page 75: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/75.jpg)
75
Pass Band Response
Fig. 15. SAW filter passband response after distortion compensation: 1 – ideal, 2 – unmatched, 3 - matched
a) magnitude b) phase
65 66 67 68 69 70 71 72 73 74 75-5
-4.5
-4
-3.5
-3
-2.5
-2
-1.5
-1
-0.5
0
Frequency, MHz
Log
mag
nitu
de |S
12|,
dB
1,3 2
65 66 67 68 69 70 71 72 73 74 75-5
-4
-3
-2
-1
0
1
2
3
4
5
Frequency, MHz
Pha
se, d
egs
1
2
3
![Page 76: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/76.jpg)
76
Smith Chart
Fig. 16. SAW filter passband response after distortion compensation: 1 – ideal, 2 – unmatched, 3 - matched
a) unmatched b) matched
< si070v1_1.s >
OC∞210.50.20SC
2j
1j
0.5j
0.2j
-0.2j
-0.5j
-1j
-2j
OC∞210.50.20SC
2j
1j
0.5j
0.2j
-0.2j
-0.5j
-1j
-2j2 1
< si070v1_1.ms >
OC∞210.50.20SC
2j
1j
0.5j
0.2j
-0.2j
-0.5j
-1j
-2j
OC∞210.50.20SC
2j
1j
0.5j
0.2j
-0.2j
-0.5j
-1j
-2j
1
2
![Page 77: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/77.jpg)
77
Modeled Time Response
Fig. 17. Modeled time response: 1 – unmatched, 2 – matched
0 1 2 3 4 5 6-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
Time, µsec
Tim
e R
espo
nse,
dB
Delay = 1.687 µsec
2 2
1
TTE
![Page 78: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/78.jpg)
78
Matching Circuit
Fig. 18. Matching circuit configuration
L1
C1
L2 50
1204.3
100 50
![Page 79: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/79.jpg)
79
Part 5. Modeling of Reflective SAW Transducers
![Page 80: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/80.jpg)
80
Coupling-of-Modes (COM) Model
Forward and backward traveling surface acoustic waves a(x) and b(x)
2
2
( ) ( )( ) ( )
Kj x
Kj xa x A x eb x B x e
−
+=
=(83)
where A(x) and B(x) are the slowly varying complex amplitudes and K=2π /p is the grating wave number.
For a reciprocal and lossless SAW transducer, the wave excitation andpropagation are described by the following system of differential COM-equations
* *
*2 2
d A j A j B j Vd xd B j A j B j Vd xd I j A j B j C Vd x
δ κ ζ
κ δ ζ
ζ ζ ω
⎧⎪⎪⎪⎪⎨⎪⎪⎪⎪⎩
= − + +
= − + −
= − − +
(84)
![Page 81: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/81.jpg)
81
COM-Parameters
δ=k-K/2 detuning parameterk unperturbated SAW wave numberκ coupling coefficientζ excitation functionC static capacitance per unit lengthI, V SAW transducer current and voltage at the electric port
![Page 82: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/82.jpg)
82
COM Mixed Scattering MatrixThe solution of the system of COM-equations (84) can be found in the closed-form by imposing the boundary conditions on acoustic and electric ports. The elements of the mixed scattering matrix take the form
*
11sinm jκ Φ
= −∆
12 21 ( 1)Nm m γ= = −
∆
( )*13 1
1 sin (1 cos )m jζ γ ζ= Φ + − Φ∆
( )23 2( 1) sin (1 cos )
N
m jζ γ ζ−
= Φ + − Φ∆
*33 1 2 1 2
4 sin(1 cos ) 2 ( )( )m Npγζ ζ ζ ζζ ζ ζ Φ= − − Φ − + −
∆ ∆
(85)
cos sinjγ δ∆ = Φ + Φ* *
1 2
δζ κ ζζγ+
=*
2 2
δζ κζζγ+
=
22 2γ δ κ= − N pγΦ =2
2 2WK
p pξ ω εζ = ≈
*jrp
κ =where
![Page 83: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/83.jpg)
83
COM Example: Reflectivity vs Finger Number
0.96 0.97 0.98 0.99 1 1.01 1.02 1.03 1.04-30
-25
-20
-15
-10
-5
0
Normalized frequency f/f0
Ref
lect
ion
coef
ficie
nt |M
11|,
dB1
2 3
Fig. 19. SAW transducer reflection: finger reflection coefficient r=- 0.01j1 – N=50, 2 – N=100, 3 – N=200
![Page 84: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/84.jpg)
84
Fig. 20. SAW transducer reflection: number of fingers N= 200,1 – r=-0.01j, 1 – r=-0.015j, 1 – r=-0.02j
0.96 0.97 0.98 0.99 1 1.01 1.02 1.03 1.04-30
-25
-20
-15
-10
-5
0
Normalized frequency f/f0
Ref
lect
ion
coef
ficie
nt |M
11|,
dB2
1 3
COM Example: Reflectivity vs Reflection Coefficient
![Page 85: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/85.jpg)
85
COM Example: Acoustoelectric Conversion
Fig. 21. Acoustoelectric conversion function: number of fingers N=100, 1 – r =-0.01j, 2 – r =0, 3 – r =+0.01j
0.96 0.97 0.98 0.99 1 1.01 1.02 1.03 1.04-40
-35
-30
-25
-20
-15
-10
-5
0
5
Normalized frequency f/f0
Nor
mal
ized
aco
usto
elec
tric
func
tion
|M13
|, dB
1 2
3
![Page 86: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/86.jpg)
86
Fig. 21. SAW transducer admittance: number of fingers N=1001 – r =-0.01j, 2 – r =0, 3 – r =+0.01j
COM Example: Radiation Admittance
0.96 0.97 0.98 0.99 1 1.01 1.02 1.03 1.04-1.5
-1
-0.5
0
0.5
1
1.5
Nor
mal
ized
radi
atio
n su
scep
tanc
eB=
ImM
33
33
1
2
3
0.96 0.97 0.98 0.99 1 1.01 1.02 1.03 1.040
0.5
1
1.5
Normalized frequency f/f00
Nor
mal
ized
radi
atio
n co
nduc
tanc
e G
=Re
M33
1 3
2
Normalized frequency f/f0a) conductance b) susceptance
![Page 87: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/87.jpg)
87
COM Example: Acoustoelectric Conversion
Fig. 21. Acoustoelectric conversion function: number of fingers N=100, 1 – r =-0.01j, 2 – r =0, 3 – r =+0.01j
0.96 0.97 0.98 0.99 1 1.01 1.02 1.03 1.04-40
-35
-30
-25
-20
-15
-10
-5
0
5
Normalized frequency f/f0
Nor
mal
ized
aco
usto
elec
tric
func
tion
|M13
|, dB
1 2
3
![Page 88: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/88.jpg)
88
Conclusions: General
1. The mixed scattering matrix M is a convenient and powerful modeling tool for simulation of the acoustoelectric devices comprising acoustic and electric ports.2. This mixed units matrix combines properties of the classical wave scattering matrix S (S-parameters) and the admittance matrix Y (Y-parameters) following by the reciprocity, power conservation, and causality.3. The mixed scattering matrix M, the wave scattering matrix S, and the admittance matrix Y are interrelated via the closed-form block-matrix equations.4. A special care must be preserved at selecting and changing the reference planes at the acoustic ports as the change in the reference planes affects the phases of the mixed scattering matrix elements.5. The closed-form expressions can be simplified by the adequate choiceof the reference planes.
![Page 89: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/89.jpg)
89
Conclusions: SAW Transducer Analysis
1. The mixed scattering matrix of a SAW transducer is a particular case of the mixed scattering matrix, with two acoustic and one electric ports.2. In general case, the mixed scattering matrix of a SAW transducer contains three independent elements m11, m13, and m33 to be determined analytically or numerically while the other elements can be found by reciprocity and power conservation.3. The electroacoustic conversion function m13 plays the key role in the SAW transducer simulation.4. In the quasi-static approximation, the closed-form equations for the mixed scattering elements can be deduced for reflectionless periodic SAW transducers.5. For reflective unapodized SAW transducers with the regular polarity sequence, the mixed scattering matrix can be deduced in the closed-form from the COM-theory.
![Page 90: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/90.jpg)
90
Conclusions: SAW Filter Modeling
1. The mixed scattering matrix can be converted to the mixed transmission matrix relating the acoustic waves at the input and output ports as well as the electric current and voltage at the electric port.2. The overall mixed scattering matrix of the multiport/multitransducer SAW device can be found by the direct interconnecting of the constituent mixed scattering matrices or by the recurrent cascading the mixed transmission matrices.3. A SAW filter comprising two in-line SAW transducers is fully characterized by the closed-form two-port admittance matrix Y (Y-parameters) that can be converted to the wave scattering matrix S (S-parameters).4. In general case, the SAW filter transmission coefficient S12 is no longer proportional the cross-admittance Y12 and therefore it has more complicated behavior than just the product of the acoustoelectric conversion functions.5. For high-quality performance SAW filters, the distortion of the function S12 must be accounted and compensated for at the SAW filter synthesis.
![Page 91: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/91.jpg)
91
Conclusions: Quasi-Static Approximation
1. In the quasi-static approximation for periodic SAW transducers, the acoustoelectric conversion function m13 can be represented as the product of the element factor ξ(ω) and the array factor F(ω), provided for a sufficient number of guard fingers at each side to suppress the electrostatic end effects.2. The element factor is the function of the metallization ratio (duty factor) and it does not depend on the particular SAW filter topology.3. It is the array factor F(ω) that specifies the frequency selective properties of SAW transducers, with the shape of the frequency response given by the Fourier Transform of a set of the electrode potentials (finger taps) or gap voltages (gap taps).3. While both the finger and gap taps models give the same results if correctly applied, the gap model is simpler as it excludes implicitly any uniform potential applied to the transducer.4. The gap element factor has weaker frequency dependence over the wide frequency range if compared to the finger element factor.
![Page 92: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/92.jpg)
92
Conclusions: Quasi-Static Approximation (Cont’d)
5. The SAW filter Y-parameters take the simplest form in the quasi-static approximation where the self-admittances Y11 and Y22 are virtually the admittances of the input and output SAW transducers while the cross-admittance Y12 is given by the product of the acoustoelectric conversion functions of both transducers.6. Examples of SAW filter modeling are given.7. Author’s design experience has confirmed good correspondence between the modeled and experimental results.
![Page 93: Mixed Scattering Matrix: Properties and Applications · Mixed Scattering Matrix: Properties and Applications. 2 ... V 1 2 b 2 a 2 I 2 b N a N b k a k V N V k I I N k N-port network](https://reader031.vdocuments.site/reader031/viewer/2022021714/5c050b1f09d3f2ff398d0193/html5/thumbnails/93.jpg)
93
The End
Thanks for your attention.
Questions?