mineral wook data sheet

Upload: jasonkkz

Post on 03-Apr-2018

215 views

Category:

Documents


0 download

TRANSCRIPT

  • 7/29/2019 Mineral Wook Data Sheet

    1/2

    SPECIALTY PRODUCTS

    & INSULATION CO.

    MINERAL WOOL PIPE INSULATION

    HEAT UP SCHEDULE

    The binder used in the pipe-sections is organic, and we

    recommend the heat-up procedure below for insulation

    with operating temperatures from 350F to 1200F.

    During commissioning, the inner part of the resin

    material will start a controlled decomposition when

    the internal temperature of the insulation exceeds

    480F (250C). Provide adequate ventilation to prevent

    build-up of gases.

    DESCRIPTION

    Mineral Wool Pipe Insulation is a precision cut pipe

    covering composed of high density mineral wool. It is

    produced in the form of two half cylinders and can be

    supplied either plain, with an all service jacket (ASJ) or

    with a foil scrim kraft (FSK) type facing. Mineral wool pipe

    insulation is available in three foot lengths in sizes from

    1/2" IPS through 20" IPS and wall thicknesses from 1" to

    4". Sizes over 20" IPS are available in curved segments.

    USES

    Mineral Wool Pipe Insulation can be used in a wide

    range of applications for hot and cold piping ranging

    from -120 to 1200F (-50 to 650C) making it

    ideal for use within:

    High temperature industrial process plants, power

    stations, petrochemical complexes, etc. for steam and

    process pipework

    Commercial hot/cold water

    Refrigerated water and similar areas

    ADVANTAGES

    Easy Fabrication - Only a knife needed for the most

    intricate shapes.

    Good Compressive Strength - Mineral Wool resists

    compression and mechanical damage.

    PERFORMANCE

    Service Temperature -120 to 1200F

    Flame Spread 5

    Smoke Development 0

    Linear Shrinkage 1%

    Stress Corrosion Does Not Promote

    Wicking Characteristics 0%

    Moisture Absorption Less than 0.1%

    Asbestos None

    Fungi & Bacteria Does Not Promote

    1200

    1100

    1000

    900

    800

    700

    600

    500

    400

    300

    200

    100

    DegreesF

    Hours

    1 2 3 4 5 6 7 8 9

  • 7/29/2019 Mineral Wook Data Sheet

    2/2

    SPECIALTY

    PRODUCTS &

    INSULATION CO.

    1097 Commercial Avenue

    East Petersburg, PA 17520-0576

    Phone: (800)788-7764

    Fax: 717-519-4046

    Email: [email protected]

    Web: www.spi-co.com

    May 2005 - Form 246

    COMPLIANCE

    ASTM C547 Standard Specification for Mineral Fiber

    Preformed Pipe Insulation (HH-I-558B)

    CAN4-S102 Surface Burning Characteristics

    ASTM E84,

    UL 723 Surface Burning Characteristics

    ASTM C411 Hot Surface Performance

    ASTM C447 Maximum Use Temperature

    ASTM C795/

    C692/C871 Stress Corrosion & Chemical Analysis

    ASTM C800 Wicking Characteristics

    ASTM C335 Thermal Conductivity

    ASTM C356 Linear Shrinkage

    ASTM C553/

    C1104(M) Moisture Absorption

    ASTM C585 Inner & Outer Diameters for Nominal

    Pipesizes

    Technical data included herein is as provided

    by respective manufacturers.

    THERMAL CONDUCTIVITY

    100 200 300 400 500 600 700(38) (93) (149) (204) (260) (316) (371)

    k, Btuin/hrft2F , W/mC

    .144

    .130

    .115

    .101

    .087

    .072

    .058

    .043

    .029

    1.00

    .90

    .80

    .70

    .60

    .50

    .40

    .30

    .20

    Warranty Disclaimers and Liability Limitations. The purchaser / user isadvised to consult with the appropriate professionals and to read the manufac-turers product information to determine the adequacy or appropriateness ofthe product for the use intended.

    Refer to the back of the SPI invoice for SPIs Warranty Disclaimers and LiabilityLimitations. These provisions generally include, without limitation, a disclaimer ofall warranties other than, to the extent assignable, an assignment of any manufac-

    turers' warranties and limitation of remedies to repair or replacement.

    Please refer to SPIs Sales and Service Center

    directory for your nearest location, or visit

    www.spi-co.com/servicecenterdirectory.mv