microsoft powerpoint - 02 oeb204700 enodeb lte v100r006 local commissioning issue 1

eNodeB LTE V100R006 Local

Commissioning

1

www.huawei.com

Copyright © 2013 Huawei Technologies Co., Ltd. All rights reserved.

eNodeB Local

Commissioning

Copyright © 2013 Huawei Technologies Co., Ltd. All rights reserved. Page1

Contents

1. Commissioning Overview

2. Local Commissioning through the USB Disk

3. Local Commissioning through the LMT


Commissioning

2


Introduction to Commissioning

� To ensure that the eNodeB operates normally after the installation

� Commissioning Modes:

� M2000-based Commissioning

� USB+M2000-based Commissioning

� Local Commissioning with LMT

� Commissioning Scenarios:

� Without a Security Gateway

� With a Security Gateway

� Commissioning Prerequisites:

� eNodeB hardware installed and ready

� Transport Network ready (for Remote Commissioning with M2000)


Scenario Without A Security Gateway


Commissioning

3


Scenario With A Security Gateway


Commissioning Mode – through USB

M2000 Server

M2000 Client

eNodeB

Remote Commissioning with M2000


Commissioning

4


Commissioning Mode – through LMT

M2000 Server

LMT

eNodeB


Contents

1. Commissioning Introduction


3. Local Commissioning through the LMT


Commissioning

5


Procedure for the Local Commissioning through the USB Disk


Procedure for the Local Commissioning through the USB Disk


Commissioning

6


Prepare for the Local Commissioning through the USB Disk

1. Obtaining a Device Panel Drawing

2. Preparing a USB Flash Drive for eNodeB

3. Preparing Dialing Test Tools

4. Performing Hardware Installation and Power-On Checks

5. Preset a Bar Code Scanner

6. Download a Software Package, Data Configuration Files,

and Deployment Lists


Obtaining a Device Panel Drawing

Page11

Step1 Obtaining accurate installation information about the

boards and modules of a base station from Huawei

technical support.


Commissioning

7


Preparing a USB Flash Drive for eNodeB

Page12

Step1 Choose Start > Programs > iManager M2000 Client > USB

Making and Protection Tool to start the tool.

Step2 Choose Make USB > Path Settings. The Path Settings dialog

box is displayed, as shown in the following figure.

Step3 Set the local save paths for the software and files, NE type, and

working mode based on the types of USB flash drive directories.

Then click OK.

Step4 Select the NE that requires a USB flash drive and deployment

mode.

Step5 Select an encryption algorithm and an integrity protection

algorithm.

Step6 In the Output Path area, specify a save path.



Page13


Commissioning

8



Page14

Step7 Click Start.

Step8 Click OK in the dialog box displayed after the tool completes the

making of the USB flash drive.

Step9 Optional: If the Local Path option is selected in the Output

Path area, copy the files to the USB flash drive.


Preparing dialing test tools

Page15

Step1 Obtaining the dialing test tools. It is used to check whether the

base station can perform services correctly. Commonly used

tools are test terminals.


Commissioning

9


Performing hardware installation and Power-On Checks

Page16

Step1 Ensure that the base station hardware has been installed and

has passed the installation checks. Different types of base

stations have different hardware installation check procedures.

For details, see Installation Checklist in the installation guide of

the corresponding base station.

Step2 Ensure that the base station has been powered on and has

passed the power-on checks. Different types of base stations

have different power-on check procedures. For details, see

Powering On base station type in the installation guide of the

corresponding base station.


Preset a Bar Code Scanner

Page17

Step1 Print the electronic operation guide on a piece of A4 paper to

facilitate scanning of presetting codes.

Step2 Connect the bar code scanner to the PC through a USB port.

Step3 Scan the presetting codes printed on the A4 paper.

Step4 Check whether the bar code scanner is preset correctly.

Note: Only when deployment ID is used to bind a base station, we

need to preset a bar code scanner.


Commissioning

10


Performing Bar-Code-Based Base Station Binding

Page18

Step1 Connect the scanner to the USB port on the main control

board of the base station.

Step2 Use the scanner to read the deployment ID in the bar code.

Step3 Check whether the scanning is successful. If the scanner

emits a tone and the scanning laser turns off, the scanning is

successful.

Step4 Remove the scanner.

Note: Only when a base station is to be bound with the deployment

ID, we need to performing bar-code-based station binding.


Download & Activate the Software and Data Configuration FileStep1 Insert the USB disk in USB port on the LMPT/UMPT of the

BBU3900

Step2 eNodeB will automatically upgrade the software and download

the data configuration file, and restart. Then verify that the

loaded software and data configuration files have taken effect.

Step3 Remove the USB flash drive after loading succeeds.


Commissioning

11


Download & Activate the Software and Data Configuration File




Commissioning

12




Performing Service Tests

Step1 Use the UE to visit the WWW server and browse web pages. Perform

this test 20 times. The success rate is higher than 95%, and the user

has no difficulty in browsing.

Step2 Use the UE to visit the FTP server and upload files. Perform this test

10 times. The success rate is higher than 90%, and the upload rates are

stable.

Step3 Use the UE to visit the FTP server and download files. Perform this

test 10 times. The success rate is higher than 90%, and the download

rates are stable.

Step4 Use the test UE to call another UE. Perform this test 20 times. The

access success rate is higher than 95%, calls are not dropped and there

is not obvious noise.


Commissioning

13


Performing ESN-based Base Station Binding by localStep1 The local engineer reports the site position and ESN of

each base station to the remote engineer.


Testing Installation and Deployment Quality

Step1 A local engineer checks that the test area has no

radiation and is safe for testing.

Step2 The local engineer checks that all cells of the base

station have been unblocked.

Step3 The local engineer checks the ports and rectifies the

problems. After the troubleshooting, the local engineer

instructs the remote engineer to resume the commissioning

task.


Commissioning

14


Checking Environmental Alarms

Step1 The local engineer performs a loopback test on an alarm port

of the UPEU using a twisted pair. The remote engineer checks

whether the M2000 receives an environmental alarm from the

alarm ports.

Step2 The local engineer stops the loopback test. The remote

engineer checks whether the alarm on the M2000 is cleared.

Step3 Both local and remote engineers repeat the preceding steps

until all eight of the alarm ports on the UPEU pass the tests.


Remote operations

In M2000 do the procedures for commissioning, including:

� Performing OM channel setup confirmation

� Acquire an NE commissioning verification report

� Confirm that auto deployment tasks are completed

� Setting the maximum output power for RF modules

� Set an NE to the NORMAL mode


Commissioning

15


Local and Remote Cooperation

The local and remote cooperation procedures for

commissioning, including:

� Performing ESN-based Base Station Binding

� Testing Installation and Deployment Quality

� Checking Environmental Alarms

� Handling Alarms


Contents

1. Commissioning Introduction


3. Local Commissioning on the LMT


Commissioning

16


Procedure for the local eNodeB commissioning on the LMT

Commission the ALD device on the

LMT

Query the running status of the

eNodeB on the LMT

Commission the environment

monitoring equipment on the LMT

Handle the eNodeB alarms on the

LMT

Download the License on the LMT

Start

End

Prepare for the Local eNodeB

Commissioning on the LMT

Upgrade the eNodeB Software and

Data Configuration File on the LMT

Establish the OM link between the

M2000 and the eNodeB

Verify the basic services of the

eNodeB

Same as the operation in

“Remote Commissioning on the

M2000

”Commission the antenna system

on the LMT

Set the maximum TX power of RRU

or RFU

Set the eNodeB status

Compare the license file with the

configuration data of eNodeB

Local operation .

Remote operation


Prepare for the Local eNodeB Commissioning on the LMT� Arranging for Related Information and Tools Required for

the eNodeB Commissioning on the LMT

� Collect the information related to the eNodeB

� Refer to the operation in “eNodeB LTE Remote Commissioning”

� Arrange for the tools required for the local commissioning on

the LMT

� Laptop

� Ethernet cable for connection to LMPT / UMPT

� Adapter for Local Maintenance for connection to UMPT


Commissioning

17


Connecting To eNodeB With LMPT

Page32

1. LMPT 2.Ethernet Cable 3. PC

Default Local OM IP

address:

192.168.0.49

Setting PC IP same

segment, such as:

192.168.0.88


Connecting To eNodeB With UMPT

Page33

1.UMPT 2.Adapter for Local Maintenance 3. Ethernet cable 4. PC

Default Local OM IP

address:

192.168.0.49

Setting PC IP same

segment, such as:

192.168.0.88

12

4 3


Commissioning

18


Login into Web LMT

Page34

Local OM IP address:192.168.0.49

User name: admin

Default password: hwbs@com


Configure FTP Server Info

� Configuring the FTP Server

Figure1. Software Management tab page


Commissioning

19


Configure FTP Server Info


Upgrade the eNodeB Software and Data Configuration File on the LMT


Commissioning

20


Software Storage

Page38

eNodeBSoftware A

eNodeBSoftware B

Main Area Standby Area

Working Standby

Store downloaded softwareActivate


Software Rollback

� Command:

� RBK SOFTWARE

� Notes: Before implement software rollback, we should

check if there is any valid software for rollback, using the

following command:

Page39


Commissioning

21


Download the License on the LMT

� After downloading the commissioning license to the eNodeB

on the LMT, you are authorized to use the eNodeB software

� Procedure

� Run the INS LICENSE command to download and activate the

license file on the eNodeB


Handle eNodeB Alarms on the LMT

� On the LMT, click the Alarm/Event button. The

Alarm/Event tab page is displayed

� Check for active alarms on the Engineering Alarm tab

page of the Browse Alarm/Event tab page

� Double-click an active alarm. Detailed Information dialog

box is displayed

� Click Solution... to know the detailed information and alarm

handling procedure. Clear the active alarm by following the

alarm handling procedure.


Commissioning

22


Query the Running Status

� On the LMT, click the Selftest

button. On the displayed Selftest

tab page, an MML command

script with the complete

parameter settings is

automatically imported to the

command area

� Click the Go button. The test

result is displayed in the area

below the Go button

Page42


Set the eNodeB Status

Page43


Commissioning

23


Local Commissioning with MML

Page44

Start

Remove Default

Configuration Data

Configure Device Data

Configure Transmission

Data

Configure Radio Data

End

Configure global Data


Remove Default Configuration Data

Page45


Commissioning

24


Configure Global Data

Page46


Configure Global Data

Page47


Commissioning

25


Configure Device Data (Procedure)



Page49


Commissioning

26



Page50



Page51


Commissioning

27


Configure and Commission ALDs

Page52


Commissioning RET Only

Page53

RET+STMA RET+SBT RET Only


Commissioning

28


Commissioning RET and Smart Bias Tee

Page54



Commissioning RET and Smart TMA

Page55



Commissioning

29


Configure Monitoring Units

Page56


Configure Time and Synch. Data

Page57


Commissioning

30


Configure Transmission Data

Page58


Key MO to configure

Page59

ACLACLRULE

IKEPROPOSALIKEPEER

IPSECPROPOSALIPSECPOLICY

PSECBINDPACKETFILTER

CERTMKAPPCERTTRUSTCE

RT

CROSSCERT

� Digital

Certificate

ADD ETHPORT

LinkEnd Point

ADD DEVIP

ADD IPRT

ADD SCTPLNK

ADD CPBEARER

ADD S1INTERFACE

ADD X2INTERFACE

ADD IPPATH(S1&X2)

ADD ENODEBPATH

ADD DEVIP

ADD IPRT

ADD SCTPTEMPLATE

ADD SCTPHOST

ADD SCTPPEER

ADD USERPLANEHOST

ADD USERPLANEPEER

ADD EPGROUP

ADD

SCTPHOST2EPGROUP

ADD

SCTPPEER2EPGROUP

ADD

UPHOST2EPGROUP

ADD

UPPEER2EPGROUP

ADD S1

ADD X2

ADD OMCH

ADD VLANMAP

SET DSCPMAP

ADD VLANCLASS

� Transmission Security


Commissioning

31


Configuring Radio Data


Configure Sectors

Page61


Commissioning

32


Configure Cells

Page62


Configure Neighboring Cells

Page63


Commissioning

33


Summary

� eNodeB commissioning Modes

� Commissioning Preparations

� The procedure of local commissioning through the USB

Disk

� The procedure of local commissioning through the LMT

� The procedure of local commissioning through LMT with

MML commands.

Thank youwww.huawei.com

microsoft powerpoint - 02 oeb204700 enodeb lte v100r006 local commissioning issue 1

Documents

commissioning overview2

commissioning introduction2

huawei technologies

lmt commissioning scenarios

usb diskcopyright

usb disk1

usb path settings

enodeb hardware