microprocessor keep your µp under control during power-on … · 2015-04-17 · microprocessor...
TRANSCRIPT
®MIC
RO
PR
OC
ESSO
R (
µP)
SUP
ERV
ISO
RY
Low PowerVoltage DetectorHi-Flex Adjustable Delay
Time Reset ICSingle
Voltage Monitor
®
Prod
uct G
uide
Micro processors require a reset pulse during power-on to initialize the internal registers and prevent unwanted code execution. Without a reset, the device could attempt to run even when the clock oscillator or VCC has not stabilized, thereby causing unpredictable operation.
Why use a Microprocessor Reset?The fundamental application of a MPS (Microprocessor Supervisory) circuit is to keep the microprocessor of a system under control. Thus a system with a good µP Supervisory circuit can greatly enhance the quality and reliability of the product.
A Microprocessor R/C Circuit vs. Reset ICIn many cases, designers use R/C Circuit to perform System Reset function in their applications. However, R/C circuit have inherent defects in its design. For example, it is not able to provide reliable reset signals when the supply voltage fluctuates below the threshold voltage. It can also cause unpredictable system behaviors, for example, if the system is power cycled in short intervals, the capacitor can not completely discharge and, the circuit may not generate a reliable reset signal.
If the system designer uses a Reset IC in their system, the IC can reliably generate a reset signal even if the supply voltage fluctuates below the threshold voltage, and additionally, if the system is powered cycled in short intervals. The Reset IC ensures that reliable reset signals are generated to guarantee reliable system power-up.
Volta
ge
Time
Power Supply
Microprocessor in Unknown state
Power-on without reset
Volta
ge
Time
RESET
Power Supply
Microprocessor initializes Correctly
Power-on with reset
Keep Your µP Under Control During Power-OnMicroprocessorSupervisory IC
USB PowerSwitch
MicroprocessorSupervisory IC
MicroprocessorSupervisory IC
®
Microprocessor Reset ........................... 1
Fixed Delay Time Reset IC .................... 2
Adjustable Delay Time Reset IC ............ 3
Watchdog Timers ................................. 4
ContentsSingle Voltage Monitors ....................... 5
Multi-Voltage Monitors ......................... 6
Selector Guide ................................. 7-9
Product Guide ..................................... 9
Microprocessor Reset ICs
®®
All trademarks are property of their respective owners
Fixed Delay Time Reset ICsPericom’s Reset ICs families provide fixed delay time function. They can be used as delayed timing devices with delay settings in 200ms, 1570ms, 1.4ms, 1.5ms, 30ms, 26ms, 0.07ms and 1680ms etc. The Reset ICs families with Fixed Delay Time are listed in the table below.
Reset ICs Series Delay Time Package
PT7M7809x/PT7M7810x/PT7M7811x 200ms SOT23-3/SOT23-5/SOT143
PT7A75xx 200ms SOT23-5/SOT143
PT7M68xx 0.07ms,1.5ms,30ms,200ms,1680ms SOT23/SC70
PT7M6314/6315 1.4ms,26ms,200ms,1570ms SOT143
PT7M64xx 200ms SOT23/SC70/DFN1.6x1.6
Application Circuit: Embedded/Portable Device Application
PT7M64xxNL
Vcc1Vcc1/Vcc2
RLRIN
C
RESETVcc RST
GND
DC LinearRegulator
PT7A75xx
µP Supervisory
Circuit
Vcc
Vcc
RESET RESET
WDI
WDO
PFO
I/O Line
NMI
Interrupt
PFI
MR
IN
OUTµP
2
CPU
ResetIC
VCC
VCCVCC
/RST
RESET ICR/C Circuit
Comparison of R/C Circuit and Reset IC Functionality
threshold
CPU
/RST
VDD
VCC
RC Reset
/RST
VCC
What are μP Supervisory Functions ?Pericom’s Supervisory ICs integrate functions such as a Manual-Reset (MR) input, Watchdog Timer, and Fixed Delay Timer or Adjustable Delay Timer. Devices such as, PT7M6118-6150 and PT7M6418-6450, provide ultra -small, 1.6mm x 1.6mm, DFN packages. These Reset ICs are perfect matches for applications with limited board space.
Application Circuit: Networking Segment eg: GPON/EPON, Switch & Router
®
www.pericom.com
3-Wire Interface RTC’s
PT7M3808xx Features
®
Hi-Flex Adjustable Delay Time Reset ICsPericom’s Hi-Flex Adjustable Reset IC families provide adjustable delay time function. These can be used in applications that require variable delay time. Some designs may require 2s delay time in one case and 0.x ms delay time in another. Our Adjustable Delay Time Reset ICs provide adjustable delay time setting with the flexibility for customer’s application.
1
2 3
4 1
2 3
4Cd
VCC/RST
GND3 4
5
1
2
RST GND
CdVCC
Cd VCC
RSTGND
GND
SC70-4 DFN 1SOT23-5
Application Circuit: Networking & Embedded Segment
Note: Capacitor-Adjustable Delay application.
ÎÎ Power-On Reset Generator with Adjustable
ÎÎ Very Low Quiescent Current: 2.4µA typ
ÎÎ High Threshold Accuracy: 0.5% typ
ÎÎ Fixed Threshold Voltages for Standard
Voltage a logic low.
ÎÎ Manual Reset (MR) Input thresholds.
ÎÎ Open-Drain RESET Output
ÎÎ Operating Temperature Range:
-40°C to +125°C
ÎÎ Package: TDFN2.0x2.0-6L and SOT23-6L
61
2
3 4
5
MR MR
GND GND
RESET RESETVDD VDD
CT CT
SENSE SENSE
(TOP VIEW) (TOP VIEW)
TDFN 2.0x2.0-6L SOT 23-6L
1 6
2 5
3 4
Connect an external capacitor (CCdelay ) from Cd to GND delay period.
tdelay=Cd×4×106+40μs
There is a fixed short delay (40µs, typ) for the output deasserting when Vin falls below Vth.
PT7M65xx Features
ÎÎ Operates from VCC of 1.2V to 5.5V
ÎÎ Capacitor-Adjustable Delay
ÎÎ Active-High/-Low Output Options
ÎÎ Open-Drain /Push-Pull Output Options
ÎÎ Low Supply Current (2µA, Typ.)
ÎÎ Operating Temperature Range: -40°C to +85°C
ÎÎ Ultra-Small 4-Pin DFN Package or SOT23 Package or SC70-4 package
Microprocessor
Input
Reset Output Reset
Rup
GNDGND
3
2
1
4VDD
VDD
CDCDPT7M65xxNL
Series
3
®
PT7A75xx: Watchdog TimersMany microprocessors integrate a watchdog timer as a low cost means for ensuring that the processor executes within proper code boundaries. However, the watchdog operates from the same supply voltage and clock inputs as the processor, it is often subject to the same transient errors. These designs are also vulnerable to software errors such as runaway code, which can disable the built-in timer.
Designers should use an external watchdog timer to guarantee proper inputs to the processor each and every time. Pericom’s PT7A75xx series can offer µP Supervisors IC with watchdog function and Manual Reset function.
PT7A75xx FeaturesThe PT7A751X/752X/753X family of microprocessor (µP) Supervisory circuits are targeted to improve reliability and accuracy of power-supply circuitry in µP’s systems. These devices reduce the complexity and number of components required to monitor power-supply and battery functions.
Application Circuit: Networking Segment/Digital Media Application.
DSP
PT7M3808G12 PT7M3808G33
1.2V 3.3V
GPIO
GND
VIO VCORESENSE
RESET
GNDCT
VDD SENSE
GND
MRRESET
VDD
CT
Selecting the RESET Delay TimeThe PT7M3808 has three options for setting the RESET delay time:
1. A fixed 300ms typical delay time by tying CT to VDD through a resistor from 40kΩ to 200kΩ.
2. A fixed 20ms delay time by leaving the CT pin open.
3. A ground referenced capacitor connected to CT for a user-defined program time between 1.25ms and 10s. The capacitor CT should be ≥ 100pF nominal value in order for the PT7M3808xxx to recognize that the capacitor is present. The capacitor value for a given delay time can be calculated using the following equation:
ÎÎ Precision supply-voltage monitor - 4.63V (PT7A7511, 7521, 7531) - 4.38V (PT7A7512, 7522, 7532) - 3.08V (PT7A7513, 7523, 7533) - 2.93V (PT7A7514, 7524, 7534)
- 2.63V (PT7A7515, 7525, 7535)
ÎÎ 200ms reset pulse width
ÎÎ Debounced TTL/CMOS-compatible manual- reset input
ÎÎ Independent Watchdog Timer 1.6sec time-out (not available for PT7A7531 - 7535)
ÎÎ Reset Output Signal: - Active-low only (PT7A7511 - 7515) - Active-high only (PT7A7521 - 7525)
- Active-high and active-low (PT7A7531 - 7535)
ÎÎ Voltage monitor for power-fail or low battery warning
ÎÎ Guaranteed RESET/RESET valid at VCC=1.2V
VCC RESET
WDI
WDO1
2
3
4
8
7
6
5 PFOPFI
GND
MR
PT7A7511P-7515PPT7A7511W-7515W
8-Pin SOIC
VCC RESET
WDI
WDO1
2
3
4
8
7
6
5 PFOPFI
GND
MR
PT7A7521P-7525PPT7A7521W-7525W
8-Pin SOIC
VCC RESET
NC
RESET1
2
3
4
8
7
6
5 PFOPFI
GND
MR
PT7A7531P-7535PPT7A7531W-7535W
8-Pin SOIC
CT(nF)=[tD(s)-0.5x10-3(s)]x1.75
4
®
www.pericom.com
PT7M61xx/ PT7M68xx: Single-Voltage MonitorsUltra Low-Power Voltage detectors monitor battery, power-supply and system voltages, without delay time
1
SC70-3
2
3
1
SC70-4 UDFN 1.6x1.6-4L
2
4
3
1
SOT23-3
2
3
1
2
SOT23-5
3
3
4
4
3 NC
GNDRSTRST
VCC
1
2
RST
VCC
GND
NC
GND
RST
VCC
GND
RST
VCC
GND
GND
NC VCC
RST
ÎÎ Highly accurate: ±1.5% (25°C)
ÎÎ Low Power Consumption: 1µA @ 3.6V Vcc
ÎÎ Detect Voltage Range: 1.8 to 5V in 100mV increments
ÎÎ Operating Voltage Range: 1.2V ~ 5.5V
ÎÎ Operating Temperature Range: -40°C to + 85°C
ÎÎ Detect voltage accuracy over temperature: ±2.5% x Typ
ÎÎ Output Configuration: N-channel open drain or CMOS
ÎÎ Available SC70/SOT23/DFN1.6X1.6 package
PT7M61xx Features:
RIN RL
C
VIN
PT7M61xxNL
GND
RSTVCC
ÎÎ Factory-Set Reset Threshold Voltages for
Nominal Supplies from 1.2V to 1.8V
ÎÎ Low Power Consumption :Typ 7.5µA
ÎÎ Five different time out periods available: 70μs (voltage detector), 1.5ms, 30ms, 210ms and 1.68s
ÎÎ Output Configuration: Push-pull RESET,
Push-pull RESET or Open-drain RESET
ÎÎ Guaranteed reset valid to VCC:
0.9V—active low, 0.85V—active high
ÎÎ Detect voltage accuracy: 1.5%
ÎÎ Adjustable Threshold Reset-in Option
ÎÎ Immune to short negative VCC transients
ÎÎ Small SOT23-3, SC70-3 or SOT143-4 packages
SC70-4
RESET(RESET)
VCC
1
2
4
3NC
PT7M6832PT7M6833PT7M6834
SC70-3
RESET(RESET)
VCC
1
2
3
PT7M6832PT7M6833PT7M6834
SOT143
RESET(RESET)
VCC
1
2
4
3MR
PT7M6832PT7M6833PT7M6834
SOT143
RESET(RESET)
VCC
1
2
4
3RESET-IN
PT7M6838PT7M6838PT7M6840
0 is for PT7M68390 is for PT7M6836
GND GND
GND GND
PT7M61xx Application Circuit: Portable Devices/Embedded Segment
PT7M68xx Features:
5
PT7M68xx: Ultra Low Power Voltage Detectors
®
PT7M6709/6714: Multi-Voltage MonitorsLow quad voltage monitors provide accurate monitoring of up to four supplies without any external components.
PT7M6709/6714
Application Circuit: VOIP Phone/Meter Applications
1.2V
3.3V
VCC
R1
VCC
VCC
RESET
PT7M6834G/F
PT7M6838/6839/6840DC/DCCONVERTER
μP
RESET
RESET-IN
CORESUPPLY
I/OSUPPLY
R2
Vmonitored
RESET(RESET)
0 is for PT7M6839
R1 = R2 ( Vmonitored/VREF-1)
External Setting of Adjustable Threshold
IN2
1
2
3
4
5
10
9
8
7
6
IN4
IN3
IN1 VCC
GND
PWRGD1
PWRGD3
PWRGD2
PWRGD4
PT7M6709
MSOP
PF11
1
2
3
4
5
10
9
8
7
6
PF13
PF12
MR VCC
GND
RESET
PFO2
PFO1
PFO3
PT7M6714
MSOP
Application Circuit: Embedded Segment, eg. LED Timing Sequence Application
1
2
3
4
5
105V Supply
9V Supply
VCC
SUPPLIESTO BE
MONITORED SYSTEMLOGIC
μP
PT7M6709
9
8
7
6
1
2
3
4
5
10
RESET
I/O
I/O
VBATT
VCC
9
8
7
6
2.0V to 5.5VMay be one of the Monitored Voltages
3.3V SupplyVCC
μP
MR
PF11
VCC
PF03GND
PF12
PF13
RESET
PF01
PF02
PT7M6714
IN1
IN2
VCC
PWRGD1GND
IN3
IN4
PWRGD1
PWRGD1
PWRGD1
PT7M6709/6714 Features
6
ÎÎ Monitor 4 Power-Supply Voltages
ÎÎ Factory-trimmed or User-Adjustable Threshold Options:
• Factory-trimmed thresholds for 5.0V, 3.3V, 3.0V,
2.5V and 1.8V supplies
• User-adjustable threshold monitors down to 0.62V
ÎÎ Low Current:
• PT7M6709: 15µA typical
• PT7M6714: 20µA typical
ÎÎ Four Independent, Active Low, and Open-Drain outputs
with 10µA internal Pull-up to VCC
ÎÎ 140ms Minimum Reset Time out Period (PT7M6714 only)
ÎÎ Immune to Battery Voltage Transients
ÎÎ Supply Voltage Range: 2.0V to 5.5V
ÎÎ Operating Temperature Range: -40°C to + 85°C
ÎÎ Small MSOP-10 Package
®
Pericom Microprocessor Supervisory SolutionsWATCH DOG TIMERS
Part Number Reset Active Low or High
Reset Time Watch dog Time (s)
Voltage Detection Threshold
Manual Reset
Package Remark
PT7A751xW Low 200ms 1.6s 1.25V Yes
W : SOIC-8
Suffix (x) definition Reset Threshold, 1: 4.63V 2: 4.38V 3: 3.08V 4: 2.93V 5: 2.63V
PT7A752xW High 200ms 1.6s 1.25V Yes
PT7A753xW Low&High 200ms - 1.25V Yes
COMMON RESET IC
Part Number
/RESET output RESET output
(push-pull)
Manual Reset
Power Fail Detector
Watch Dog Input
Reset Time
Package Remark
Push-Pull Open-Drain
PT7M7803xT - √ - - - - 200ms SOT23-3 Suffix (x) definition Reset Threshold, L:4.63V M:4.38V J:4.00V T:3.08V S:2.93V G:2.80V R:2.63V Z:2.32V
PT7M7809xT √ - - - - - 200ms SOT23-3
PT7M7810xT - - √ - - - 200ms SOT23-3
PT7M7811xTA √ - - √ - - 200ms SOT23-5
PT7M7812xTA - - √ √ - - 200ms SOT23-5
PT7M7811xTB √ - - √ - - 200ms SOT143-4
PT7M7812xTB - - √ √ - - 200ms SOT143-4
PT7M7823xTA √ - - √ - √ 200ms SOT23-5
PT7M7824xTA √ - √ - - √ 200ms SOT23-5
PT7M7825xTA √ - √ √ - - 200ms SOT23-5
SINGLE & DUAL VOLTAGE MONITOR
Part Number Output Voltage Detectors Threshold Package Remark
Open-Drain Push-Pull Single Dual User adjustable
Active high Active low Active low
PT7M7433TA - - √ √ - √ SOT23-5
PT7M7434TA - √ - √ - √ SOT23-5
PT7M7435TA √ - - √ - √ SOT23-5
PT7M7436TA - - √ - √ √ SOT23-6
PT7M7437TA - √ - - √ √ SOT23-6
PT7M7438TA √ - - - √ √ SOT23-6
BI-DIRECTIONAL MONITOR
Part Number Reset Output Suffix (xx) definition Reset Threshold Reset Time Package Remark
PT7M1818-xx# Bi-direct, Active low xx=20:2.5V; xx=10:2.9V; xx=5:3.0V; 200ms # =T:SOT23-3
PT7M1813-xx# Bi-direct, Active low xx=15:4.1V; xx=10:4.3V; xx=5:4.6V. 200ms
PT7M1233-xx# Bi-direct, Active low xx=15:4.1V; xx=10:4.3V; xx=5:4.6V 200ms #=T: SOT23-3
PT7M1233A-xx# Bi-direct, Active low xx=10:2.88V; xx=5:2.72V 200ms
SINGLE VOLTAGE MONITOR (with Fixed Delay Time)
Part Number Reset Output Threshold Reset Time
Package Remark
Open-Drain Push-Pull Bi-direct
Active high Active low Active high Active low Active low
PT7M64xxCL# - - - √ - 1.8V to 5.0V in 100mV increments
200ms #=TA3:SOT23-3 #=TA5:SOT23-5 #=C3: SC70-3 #=C4: SC70-4 #=XV4:DFN-4
(xx) refers to voltage range, 1.8V to 5.0V. For example, PT7M6418, thres- hold voltage is1.8V.
PT7M64xxCH# - - √ - - 200ms
PT7M64xxNL# - √ - - - 200ms
µP SUPERVISORY PRODUCT SELECTION GUIDEPericom offers a diverse range of accurate, low cost µP Supervisory solutions for handheld & embedded applications
CONTINUED.. 7
®
µP SUPERVISORY PRODUCT SELECTION GUIDE (cont..)SINGLE VOLTAGE MONITOR (No Delay Time)
Part Number Reset Output
Threshold PackageRemark RemarkOpen-Drain Push-Pull
Active high Active low Active high Active low
PT7M61xxCL# - - - √ 1.8V to 5.0V in100mV increments
#=TA3:SOT23-3 #=TA5:SOT23-5 #=C4:SC70-4#=XV4:DFN-4
(xx) refers to voltage range, 1.8V to 5.0V (Vcc fall to Vth). For example, PT7M6118, thresh-old voltage is 1.8V.
PT7M61xxCH# - - √ -
PT7M61xxNL# - √ - -
SINGLE VOLTAGE MONITOR (No Delay Time)
Part Number Reset Output
Threshold Package RemarkOpen-Drain Push-Pull
Active high Active low Active high Active low
PT7M62xxCL# - - - √ 1.8V to 5.0V in100mV increments
#=TA3:SOT23-3, #=TA5:SOT23-5, #=C4:SC70-4
(xx) refers to volt-age range, 1.8V to 5.0V(Vcc rise to Vth). For example, PT7M6218, thresh-old voltage is 1.8V.
PT7M62xxCH# - - √ -
PT7M62xxNL# - √ - -
SINGLE VOLTAGE MONITOR (Adjustable Delay Time)
Part Number Reset Output
Threshold
Reset Time
Package RemarkOpen-Drain Push-Pull
Active high Active low Active high Active low
PT7M65xxCL# * - - - √ 1.8V to 5.0V in100mV increments
Adjustable #=TA5:SOT23-5 #=C4: SC70-4 #=XV4:DFN-4
(xx) refers to voltage range, 1.8V to 5.0V. For example, PT7M6518, thresh-old voltage is 1.8V.
PT7M65xxCH# * - - √ - Adjustable
PT7M65xxNL# * - √ - - Adjustable
SINGLE VOLTAGE MONITOR (Ultra Low Voltage)
Part Number Reset Output
Threshold Package RemarkOpen-Drain Push-Pull
Active high Active low Active high Active low
PT7M610xCL# - - - √ x=1: 0.1V x=2: 0.2V
#=C4: SC70-4 #=TA: SOT23-5
PT7M610xCH# - - √ -
PT7M610xNL# - √ - -
MULTI-VOLTAGE MONITOR (Quad Voltage)
Part Number Nominal Input VoltagePackage Remark
IN1 (V) IN2 (V) IN3 (V) IN4 (V) Supply Tolerance(%)
PT7M6709AU 5 3.3 2.5 Adj* 10 MSOP-10 *Adjustable voltage based on 0.62V internal threshold. External threshold voltage can be set using an external resistor-divider.
PT7M6709BU 5 3.3 2.5 Adj* 5 MSOP-10
PT7M6709CU 5 3.3 1.8 Adj* 10 MSOP-10
PT7M6709DU 5 3.3 1.8 Adj* 5 MSOP-10
PT7M6709EU Adj* 3.3 2.5 1.8 10 MSOP-10
PT7M6709FU Adj* 3.3 2.5 1.8 5 MSOP-10
PT7M6709GU 5 3.3 Adj* Adj* 10 MSOP-10
PT7M6709HU 5 3.3 Adj* Adj* 5 MSOP-10
PT7M6709IU Adj* 3.3 2.5 Adj* 10 MSOP-10
PT7M6709JU Adj* 3.3 2.5 Adj* 5 MSOP-10
PT7M6709KU Adj* 3.3 1.8 Adj* 10 MSOP-10
PT7M6709LU Adj* 3.3 1.8 Adj* 5 MSOP-10
PT7M6709MU Adj* 3 Adj* Adj* 10 MSOP-10
PT7M6709NU Adj* 3 Adj* Adj* 5 MSOP-10
PT7M6709OU Adj* Adj* Adj* Adj* N/A MSOP-10
8
®
MULTI-VOLTAGE MONITOR (Quad Voltage)
Part Number Nominal Input VoltageSupply Tolerance(%) Package Remark
Vcc (V) PF11 (V) PF12 (V) PF13 (V)
PT7M6714AU 5 Adj* Adj* Adj* 10 MSOP-10MSOP-10MSOP-10MSOP-10
*Adjustable voltage based on 0.62V internal threshold.External threshold voltage can be set using an external resistor-divider.
PT7M6714BU 5 Adj* Adj* Adj* 5
PT7M6714CU 3.3 Adj* Adj* Adj* 10
PT7M6714DU 3.3 Adj* Adj* Adj* 5
Ultra Low Voltage Monitor (with 5 Fixed Different Delay Time)
Part Number Reset Output
Reset Time Package RemarkOpen-Drain Push-Pull
Active high Active low Active high Active low
PT7M6832xDx# - - - √ Suffix Dx refers to Reset Time D0: 0.07ms D1: 1.5ms D2: 30ms D3: 210ms D4: 1680ms
#=TA3: SOT23-3 #=C3: SC70-3 #=TB: SOT143-4
PT7M6832-PT7M6837: (x) refers to voltage range, W:1.665v, V:1.575v, I:1.388v, H:1.313v, G:1.11v, F:1.050v PT7M6838-PT7M6840: Adjustable voltage based on 0.444V internal threshold
PT7M6835xDx# - - - √
PT7M6838Dx# - - - √
PT7M6833xDx# - - √ -
PT7M6836xDx# - - √ -
PT7M6839Dx# - - √ -
PT7M6834xDx# - √ - -
PT7M6837xDx# - √ - -
PT7M6840Dx# - √ - -
SINGLE VOLTAGE MONITOR (with 4 Fixed Different Delay Time)
Part Number Reset Output
Reset Time Package RemarkOpen-Drain Push-Pull
Active high Active low Active high Active low
PT7M6314USxxDx# - √ - - Suffix Dx refers to Reset Time D1:1.4ms,D2:26ms D3:200ms,D4:1570ms
#=TB:SOT143-4 (xx) refers to voltage range, 2.5V to 5.0V. For example, PT7M6315US25, threshold voltage is 2.5V.
PT7M6315USxxDx# - √ - -
CONTINUED.. https://www.pericom.com/products/Power-Management-IC/microprocessor-supervisory-IC/
µP SUPERVISORY PRODUCT SELECTION GUIDE (cont..)
9
®
PT7A75xx
Threshold Voltage2.63V, 2.93V, 3.08V, 4.38V, 4.63
Threshold Voltage2.32V, 2.63V, 2.93V, 3.08V, 4.0V,4.38V, 2.2V, 2.25V, 4.63V, 2.8V
Threshold Voltage1.8V ~5.0V increment 0.1V
Threshold Voltage1.63V, 1.58V, 1.41V, 1.050V
Threshold VoltageFixed voltage /Adjustable by external resistor
PT7M78xxPT7M61xx (No Delay Time)PT7M644xx (200ms Delay Time)PT7M65xx (Adjustable Delay Time)
PT7M68xxUltra-Low Voltage
PT7M6709/6714
Features:1. POR (Power on Reset)2. Power Failure Detection3. Watch Dog4. Manual Reset
Applications:1. Datacom Router/Switch2. Telecom: BSC, RRC, BBO,CO 3. Industrial Control device
Applications:1. STB/LCD TV2. XDSL, EPON/GPON3. Switch, VOIP4. GPS/PND
Applications:Portable Devices:PND, MID, Smartphone,Mobile POS
Applications:New chipset with Low voltage System or Battery power system.
Applications:1. Multi-suppliers2. Telecom, Datacom3. Multi-monitor device
Features:1. POR (Power on Reset)2. Power Failure Detection3. Manual Reset
Features:1. Ultra Low Voltage2. POR (Power on Reset)3. Five Delay Time (1.5ms, 30ms, 210ms & 1.68ms)
Features:1. Multi Channel Monitors2. Multi Voltage Detector(4-Channel Detector)
Features:1. Low current <1uA2. Monitoring Battery3. Over Charger/Over Discharger protection4. POR Power on Reset
Package: PDIP-8 SOIC-8
Package: SOT23-3 SOT143-4
Package: SOT23, SC70 DFN1.6 x 1.6
Package: SC70
Package: MSOP-10
WatchdogTimers
CommonReset IC
Ultra-LowVoltage Monitors
Multi-Voltage Monitors
Single VoltageMonitors
uP Supervisory Series
UP Supervisory Brochure - April/2015
µP SUPERVISORY PRODUCT FAMILY GUIDE
10Europe: 1-408.232.9090 USA: 1-408.232.9100 China: +86-21-6119.5688 Japan: +81-3-5789.5526
Taiwan: +866-2-6616.0588 Korea: +82-2-6004.1307 India: +91-9845-204.957 Singapore: +65-6777 1645