methven aio aurajet overhead shower · aio aurajet overhead shower cleaning recommendations we...
TRANSCRIPT
METHVENAIO AURAJET OVERHEAD SHOWER
CLEANING RECOMMENDATIONSWe recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials. Damage caused by improper treatment is not covered by the product warranty – refer to warranty conditions.
To see the complete AIO range go to www.reece.com.au/bathrooms
SPECIFICATIONSRecommended Use Domestic, hotel and commercial
Colour Chrome, and
Chrome with white face
Pressure Rating Suitable for high pressure applications and has been WELS certified to the following:
Minimum operating pressure 100kPa
Maximum operating pressure 500kPa
Temperature Rating Maximum continuous working temperature 70°C (recommended 38°C - 42°C)
Minimum 5°C
Suitable Hot Water Units
Storage Tank: Yes Continuous Flow: Yes
Gravity Feed: Not recommended
Spray Patterns Aurajet Spray
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 1
410
1/2" BSPFemale
87
24
220
AOOSCPWHAU 2299912
AOOSCPAU 2299911
page 1 of 2
TM
WMKT21090AS/NZS 3662
The more stars the more water efficient
WATER RATINGwww.waterrating.gov.au
In accordance with AS/NZS 6400
Licence No. 0095Methven Australia Pty Ltd
9.0 litres per minute
INSTALLATION INSTRUCTIONS
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
Step 1
• Recommended installation height is 2100mm from the ground.
• Wall lining hole should be cut or finished as per the dimensionshown in the diagram on the right.
• Cut off the threaded nipple 13±2mm from the wall lining andapply thread seal tape to ensure a good seal.
Step 2
• Ensure o-ring is located on the inlet connector.
• Screw the inlet connector onto the nipple ensuring that theo-ring is sufficiently compressed to create a watertight seal.
Step 3
• Push the overhead shower onto the inlet connector.
• Ensure that the overhead shower is oriented horizontally
• Secure in place by tightening the grub screw firmly using the hex key provided
•
Step 1
Wall lining hole should be cut or finished as per the dimension shown in the diagram on the right.
Cut off the threaded nipple 13±2mm from the wall lining and apply thread seal tape to ensure a good seal.
IMPORTANT: Before you begin, turn off the water supply.
•
Step 2
Screw the inlet connector onto the nipple ensuring that the o-ring is sufficiently compressed to create a watertight seal.
•
Step 3
Push the overhead shower onto the inlet •
½" BSP Nipple(Not Supplied)
O-ring
Overhead Shower
IMPORTANT: Please read all of the instructions before installation.
General:
•
•
•
•
Methven recommends this product is installed by a licensed plumber in compliance with all relevant regional regulations.
After installation all connections must be checked for leaks.
All outlets used primarily for personal hygiene shall deliver water at a safe temperature as per regional regulations.
It is the responsibility of the installer to ensure a waterproof seal is achieved.
NOTE: Some showers may not provide an effective shower when used with gravity fed heated water systems or where pressures are less than 150kPa/1.5bar at the outlet. Additionally showers with flow rates of less than 9L/min may not allow the following to function correctly:- some instantaneous water heaters- some tempering valves- some thermostatic mixing valves
•
Inlet Connector
Ensure that the overhead shower is oriented horizontally.
•
connector.
Hex Key
Ensure o-ring is located on the inlet connector.
•
Secure in place by tightening the grub screw firmly using the hex key provided.
•
13±2mm
26mm max
•
Step 1
Wall lining hole should be cut or finished as per the dimension shown in the diagram on the right.
Cut off the threaded nipple 13±2mm from the wall lining and apply thread seal tape to ensure a good seal.
IMPORTANT: Before you begin, turn off the water supply.
•
Step 2
Screw the inlet connector onto the nipple ensuring that the o-ring is sufficiently compressed to create a watertight seal.
•
Step 3
Push the overhead shower onto the inlet •
½" BSP Nipple(Not Supplied)
O-ring
Overhead Shower
IMPORTANT: Please read all of the instructions before installation.
General:
•
•
•
•
Methven recommends this product is installed by a licensed plumber in compliance with all relevant regional regulations.
After installation all connections must be checked for leaks.
All outlets used primarily for personal hygiene shall deliver water at a safe temperature as per regional regulations.
It is the responsibility of the installer to ensure a waterproof seal is achieved.
NOTE: Some showers may not provide an effective shower when used with gravity fed heated water systems or where pressures are less than 150kPa/1.5bar at the outlet. Additionally showers with flow rates of less than 9L/min may not allow the following to function correctly:- some instantaneous water heaters- some tempering valves- some thermostatic mixing valves
•
Inlet Connector
Ensure that the overhead shower is oriented horizontally.
•
connector.
Hex Key
Ensure o-ring is located on the inlet connector.
•
Secure in place by tightening the grub screw firmly using the hex key provided.
•
13±2mm
26mm max
•
Step 1
Wall lining hole should be cut or finished as per the dimension shown in the diagram on the right.
Cut off the threaded nipple 13±2mm from the wall lining and apply thread seal tape to ensure a good seal.
IMPORTANT: Before you begin, turn off the water supply.
•
Step 2
Screw the inlet connector onto the nipple ensuring that the o-ring is sufficiently compressed to create a watertight seal.
•
Step 3
Push the overhead shower onto the inlet •
½" BSP Nipple(Not Supplied)
O-ring
Overhead Shower
IMPORTANT: Please read all of the instructions before installation.
General:
•
•
•
•
Methven recommends this product is installed by a licensed plumber in compliance with all relevant regional regulations.
After installation all connections must be checked for leaks.
All outlets used primarily for personal hygiene shall deliver water at a safe temperature as per regional regulations.
It is the responsibility of the installer to ensure a waterproof seal is achieved.
NOTE: Some showers may not provide an effective shower when used with gravity fed heated water systems or where pressures are less than 150kPa/1.5bar at the outlet. Additionally showers with flow rates of less than 9L/min may not allow the following to function correctly:- some instantaneous water heaters- some tempering valves- some thermostatic mixing valves
•
Inlet Connector
Ensure that the overhead shower is oriented horizontally.
•
connector.
Hex Key
Ensure o-ring is located on the inlet connector.
•
Secure in place by tightening the grub screw firmly using the hex key provided.
•
13±2mm
26mm max
www.methven.com
Never use abrasives or abrasive cleaning agents to clean this product. Clean regularly with contamination free warm soapy water and a damp soft cloth.
Clean filter washer located in the shower head waterway periodically. To access filter washer,
Care and Cleaning:
If shower performance is compromised by the build-up of lime-scale, soak in limescale remover for up to 10 minutes. Refer to instructions above for how to remove shower head
these can damage the shower. Always rinse the shower thoroughly after cleaning to remove cleaning products that can damage the shower.
Never insert objects into the spray slot or attempt to remove limescale with sharp objects or abrasives.
Technical Specifications:Operating Pressure:Min: 100kPa/1barMax: 500kPa/5bar*Optimum: 150kPa/1.5bar - 500kPa/5bar
Operating Temperature:Hot: Max 70°C*Cold: Min 5°C
Inlet Connections:All ½" BSP
* Regional specific regulations apply. Please refer to your warranty statement at www.methven.com
AURAJET™ OVERHEAD SHOWERInstallation Guide
push down on release button, hold the wall arm and pull shower head away from it.
Remove filter washer from the shower head waterwayby gently levering out with a small screw driver.
Do not hang any items or pull down on the overhead shower. This may cause the overhead shower to deform.
1
2
from wall arm. Do not use products containing chlorine bleach or hydrochloric acid as
Run hot water through shower for 2 minutes before first use.
Methven warrants this product against manufacturing defects and that it is suitable for use under the general operating conditions specified in this instruction sheet. However, regional regulations apply and may affect your warranty. Please refer to www.methven.com or call customer service for full details.
New Zealand0800 804 222
Australia1300 638 483
UK0800 195 1602
439948 ISSUE
•
Step 1
Wall lining hole should be cut or finished as per the dimension shown in the diagram on the right.
Cut off the threaded nipple 13±2mm from the wall lining and apply thread seal tape to ensure a good seal.
IMPORTANT: Before you begin, turn off the water supply.
•
Step 2
Screw the inlet connector onto the nipple ensuring that the o-ring is sufficiently compressed to create a watertight seal.
•
Step 3
Push the overhead shower onto the inlet •
½" BSP Nipple(Not Supplied)
O-ring
Overhead Shower
IMPORTANT: Please read all of the instructions before installation.
General:
•
•
•
•
Methven recommends this product is installed by a licensed plumber in compliance with all relevant regional regulations.
After installation all connections must be checked for leaks.
All outlets used primarily for personal hygiene shall deliver water at a safe temperature as per regional regulations.
It is the responsibility of the installer to ensure a waterproof seal is achieved.
NOTE: Some showers may not provide an effective shower when used with gravity fed heated water systems or where pressures are less than 150kPa/1.5bar at the outlet. Additionally showers with flow rates of less than 9L/min may not allow the following to function correctly:- some instantaneous water heaters- some tempering valves- some thermostatic mixing valves
•
Inlet Connector
Ensure that the overhead shower is oriented horizontally.
•
connector.
Hex Key
Ensure o-ring is located on the inlet connector.
•
Secure in place by tightening the grub screw firmly using the hex key provided.
•
13±2mm
26mm max
IMPORTANT: Please read all of the instructions and turn off water supply before installation.
Care and Cleaning
Run hot water through shower for 2 minutes before first use.
Never use abrasives or abrasive cleaning agents to clean this product. Clean regularly with contamination free warm soapy water and a damp soft cloth.
Clean filter washer located in the shower head waterway periodically. To access filter washer, push down on release button, hold the wall arm and pull shower head away from it.
Remove filter washer from the shower head waterway by gently levering out with a small screw driver.
page 2 of 2