metal finding metalliscanner mt 7 - rs components

Zircon Corporation | 1580 Dell Avenue | Campbell, CA 95008 | [email protected] | www.zircon.com | 408-963-4550 | 800-245-9265 MetalliScanner ™ MT 7 METAL FINDING © 2017. DeepScan, MetalliScanner and Zircon are trademarks or registered trademarks of Zircon Corporation • C/N 2721 06/17 SPECIFICATIONS Dimensions 246 mm H x 107 mm W x 51 mm D Weight 308 g without battery Battery Type 9V alkaline, required Position Accuracy Centre of #4 (13 mm) rebar or 13 mm copper pipe at a minimum grid spacing of 152 mm typically within 13 mm Depth* Up to 152 mm ± 25 mm Operating Temperature -7° to 41°C Storage Temperature -29° to 66°C Humidity 5 - 90% (non-condensing) Water Resistance Splash resistant, not waterproof *NOTE: Specifications subject to change. Sensing depth and accuracy can vary due to moisture, content of materials, wall texture, paint, etc. Scan for Metal ZirconTV ZirconCorporation ZirconTools ZirconToolPro ZirconTools The MetalliScanner ™ MT 7 electronic metal locator is designed for ﬁnding metal in standard residential, commercial, and industrial construction. The bright, backlit display indicates the metal target depth (in both inches and centimeters) up to 15 cm deep, the type of metal located (ferrous or non-ferrous), and whether you are moving towards or away from a target. This powerful tool saves time and money by eliminating guesswork, rework, needless holes, and costly broken drill bits or saw blades. The MT 7 helps map the grid to avoid any metal, such as rebar, through any nonmetallic construction material, including concrete, tile and marble. Other recommended uses include locating and reinforcing rebar in masonry, measuring subsurface nail spacing in rooﬁng material for compliance with building codes, and even detecting the nails/tacks in studs behind lath and plaster walls. • Features two scanning modes: Normal Scan, DeepScan ® • Locates and determines the approximate depth of 13 mm rebar and copper pipe up to 15 cm deep. • Position accuracy to within ± 13 mm for #4 rebar or 13 mm copper pipe • Automatically differentiates between magnetic metal (such as rebar) and non-magnetic metal (such as copper pipe) • Backlit display and audio tone clearly indicate location of target • Pivoting handle attachment for extended and overhead reach • Rubberized handle and built-in lanyard loop

Upload: others

Post on 26-Dec-2021

9 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: METAL FINDING MetalliScanner MT 7 - RS Components

MetalliScanner™ MT 7METAL FINDING

SPECIFICATIONS

Dimensions 246 mm H x 107 mm W x 51 mm D

Weight 308 g without battery

Battery Type 9V alkaline, required

Position Accuracy Centre of #4 (13 mm) rebar or 13 mm copper pipe at a minimum grid spacing of 152 mm typically within 13 mm

Depth* Up to 152 mm ± 25 mm

Operating Temperature -7° to 41°C

Storage Temperature -29° to 66°C

Humidity 5 - 90% (non-condensing)

Water Resistance Splash resistant, not waterproof*NOTE: Specifications subject to change. Sensing depth and accuracy can vary due to moisture, content of materials, wall texture, paint, etc.Scan for Metal

ZirconTVZirconCorporationZirconTools

ZirconToolProZirconTools

The MetalliScanner™ MT 7 electronic metal locator is designed for finding metal in standard residential, commercial, and industrial construction. The bright, backlit display indicates the metal target depth (in both inches and centimeters) up to 15 cm deep, the type of metal located (ferrous or non-ferrous), and whether you are moving towards or away from a target. This powerful tool saves time and money by eliminating guesswork, rework, needless holes, and costly broken drill bits or saw blades.

The MT 7 helps map the grid to avoid any metal, such as rebar, through any nonmetallic construction material, including concrete, tile and marble. Other recommended uses include locating and reinforcing rebar in masonry, measuring subsurface nail spacing in roofing material for compliance with building codes, and even detecting the nails/tacks in studs behind lath and plaster walls.

• Features two scanning modes: Normal Scan, DeepScan®

• Locates and determines the approximate depth of 13 mm rebar and copper pipe up to 15 cm deep.

• Position accuracy to within ± 13 mm for #4 rebar or 13 mm copper pipe

• Automatically differentiates between magnetic metal (such as rebar) and non-magnetic metal (such as copper pipe)

• Backlit display and audio tone clearly indicate location of target

• Pivoting handle attachment for extended and overhead reach

• Rubberized handle and built-in lanyard loop

santral.com · MT 058 MT 059 MT 060 MT 055 MT 079 MT 070 MT 071 MT 072 MT 073 MT 074 MT 075 MT 028 MT 056 MT 1094 MT 1095 Cinsi Bir fazll a kapama alter iki fazll aqp ka ama ¥lter

MT MT 625 MT 732 MT 932 MT 835Manitou MT … ManitouTeleskop MT 625 MT 732 MT 932 MT 835Manitou MT 1135 MT 1335 MT 1440 MT 1840 Getriebe Wandler X X X X XMotorleistung kW / PS X X

Con la versión · 2016. 7. 21. · Pirelli MT 60 RS 110/80 ZR18 Pirelli MT 60 RS 180/55 ZR17 Amortiguador trasero Kayaba, precarga ajustable Disco de 330 mm, pinza radial de 4 pistones

MT Voucher DE/EN/RS

P-MT-T · 2019. 10. 12. · P-MT-T Ambient Temperature Cloud-Connected Data Logger CALIBRATION CERTIFICATES NOW AVAILABLE RS Components oers a Traceable Calibration Certificate Service