ELG – Easy Programming

Ericsson LG

Unified Communication for Advanced Business Needs

Visit: www.ericssonlg.com

www.mecomdubai.com

Basic Techniques

Default SettingsDefault IP: 10.10.10.2

Subnet: 255.255.255.0

Switch 1, 2, 3 & 4 OFF (restart to have factory reset)

DIP switch 1 – OFF to make changes in the software

DIP switch 4 – OFF to keep the program in memory

On system running mode - keep switch 2&3 in ON position and 1&4 in OFF position

Remember to take program software backup after major changes

Basic Techniques

Web Accesshttps://10.10.10.2

To have http://10.10.10.2

Login to program mode on 24 button telephone

PGM * # PGM then the program number.

change the following

PRG 160 Flex 22 – make it OFF

PRG 161 Flex 14 – web port 0080

Change Country Code PRG100 to UAE

keep (DIP switch 1,2,3 in ON and 4 OFF) for the setup.

Basic Techniques

Telephone Access

To make changes or reset telephone to factory defaults

Press * on start up

login password 147*

Press volume up or down to reach the specifics

Make changes and press SAVE

Basic Techniques

Primary Basic MUST Date & Time (178) Change Trunk Priority (160-161) item 4 Caller ID (114 - 1 & 2) Trunk Ringing assignment (144) Trunk access and grouping (140-142, 117)

Basic Techniques

Trunk Access

Toll Exception table (224, 116)

For Trunks

CO COS 1: Station COS applies

CO COS 2: Exception Table A governs

CO COS 3: Exception Table B governs

CO COS 4: Restricts LD calls and Exception Table C

CO COS 5: Overrides Station COS

Basic Techniques

Trunk Access Toll Exception table (224, 116) - Settings for Extns:

1 - No restrictions are placed on dialing from the station.

2 - The assignments in Exception Table A are monitored for allow and deny numbers.

3 - The assignments in Exception Table B are monitored for allow and deny numbers.

4 - The assignments in both Exception Tables A & B are monitored for allow and deny numbers

5 - The leading digit dialed cannot be a Long Distance code, default “0” or “1”, and further denied/allowed based on Exception Table C.

Basic Techniques

Trunk Access (Cont..)6 - The leading digits dialed cannot be a Long Distance code & digit count cannot exceed the LD digit counter, default 7 digits, and further denied/allowed based on Exc., Table C.

7 - Intercom and paging calls are allowed. No outgoing dialing except for emergency calls is allowed on CO Lines.

8 - The assignments in the Exception Table D are monitored for allow and deny numbers.

9 - The assignments in the Exception Table E are monitored for allow and deny numbers

10 - The assignments in the Exception Table D & E are monitored for allow and deny numbers

11 - The assignments in the Exception Table A & B and D & E are monitored for allow and deny numbers.

PRI Programming - Incomming

Matched with MSN Table Entry ?

NO

YES

TYPE 1(Use ‘as is’)(ex. 1100 => 1100)

Ring toMatched NumberingDestination

Remove digits from start of incomng DID Number

DecideDAY/NIGHT/TIMEDBy Auto Ring Mode Table Index

TYPE 2 (Modify using Flexible)

TYPE 0 (DID Conversion)

DID DGT Conversion

YES

NO

PGM 202

PGM 143 –DID Remove Number

PGM 143 –COLP Table IndexPGM 201 –COLP Table Value

PGM 145 –Number of Digits Expected (from First)/ Digit Mask(ex. 1100 => 110)

Remove DID Digit Set ?

DID Call

ICLI (Incoming CLI) Usage ON ?

PGM 231- ICLID Table Usage

YES

NO

Ring to ICLID Destination

PGM 203/204 – Destination

PGM 231- Auto Ring Mode Table

PGM 231- Destination

Ring to Flexible DID Destination

Remove Matched String setBy CorrespondingCOLP TBL Index and Data

PGM 145 –DID Conversion Type

Ring toMatched NumberingDestination

DID Digit Conversion Type ?

DID DGT Conversion

PGM 145 –Number of Digits Expected (from Last)/ Digit Mask(ex. 1100 => 100)

Auto Attendant & Voice Mail Auto Attendant: VSF access (112 - 36) enabled extension VRS: CCR Table (228), Voice Mail Dialing table (234)

From enabled extension Phone

• Press Trans/PGM

• Dial 0 + 6

• Enter System Message Number (i.e. 001)

• REC Type is 1

• Press # To Start Recording (wait to listen current recording)

• Record your NEW Greeting

• Press Hold/Save to END Recording

Recording from PC VSG tab > Individual upload > file format > 1_5.wav (1 is default and 5 is message number)