1

Mercedes-Benz

Operator's Manual

300 SD

2

Product informationKindly observe the following in your own best interest:

We recommend using Mercedes-Benz original parts as well as conversion parts and accessories explicitly approved by us foryour vehicle model. We have tested these parts to determine their reliability, safety and their special suitability for Mercedes-Benz vehicles.

We are unable to make an assessment for other products and therefore cannot be held responsible for them, even if in individual casesan official approval or authorization by governmental or other agencies should exist. Use of such parts and accessories couldadversely affect the safety, performance or reliability of your vehicle. Please do not use them. Mercedes-Benz original parts as well asconversion parts and accessories approved by us are available at your authorized Mercedes-Benz Center where you will receivecomprehensive information, also on permissible technical modifications, and where proper installation will be performed.

Our company and staff congratulate you on the purchase of your new Mercedes-Benz.

Your selection of our product is a demonstration of your trust in our company name. Further, it exemplifies your desire to own anautomobile that will be as easy as possible to operate and provide years of service.

Your Mercedes-Benz represents the efforts of many skilled engineers and craftsmen. To ensure your pleasure of ownership, andfor your safety and that of your passengers, we ask you to make a small investment of your time:

• Please read this manual carefully before putting it aside. Then return it to your vehicle where it will be handy foryour reference.

• Please abide by the recommendations contained in this manual. They are designed to acquaint you with theoperation of your Mercedes-Benz.

• Please abide by the warnings and cautions contained in this manual. They are designed to help improve the safetyof the vehicle operator and occupants.

We extend our best wishes for many miles of safe, pleasurable driving.

DaimlerChrysler AG

3

Operator's manual

This Operator's Manual contains a great deal of useful information. We urge you to read it carefully and familiarize yourself with thevehicle before driving.

For your own safety and longer service life of the vehicle, we urge you to follow the instructions and warnings contained in thismanual. Ignoring them could result in damage to the vehicle or personal injury to you or others. Vehicle damage caused by failure tofollow instructions is not covered by the Mercedes-Benz Limited Warranty.

Your vehicle may have some or all of the equipment described in this manual. Therefore, you may find explanations for optionalequipment not installed in your vehicle. If you have any questions about the operation of any equipment, your authorized Mercedes-Benz Center will be glad to demonstrate the proper procedures.Owner’s Service and Warranty Policy

The Owner’s Service and Warranty Information Booklet contains detailed information about the warranties covering yourMercedes-Benz, including:

• New Car Limited Warranty,• Emission System Warranty,• Emission Performance Warranty,• State Warranty Enforcement Laws (Lemon Laws).

4

Important notice for California retail buyers of Mercedes-Benz automobiles

Under California law you may be entitled to a replacement of your vehicle or a refund of the purchase price, if Mercedes-Benz USA,LLCor its authorized Mercedes-Benz Center fails to conform the vehicle to its express warranties after a reasonable number of repair attemptsduring the period of one year or 12 000 miles from original delivery of the vehicle. A reasonable number of repair attempts is presumed fora retail buyer (1) if the vehicle is out of service by reason of repair of substantial nonconformities for a cumulative total of more than 30calendar days or (2) the same substantial non-conformity has been subject to repair four or more times and you have at least oncedirectly notified us in writing of the need to repair the non-conformity and have given us an opportunity to perform the repairourselves. Notifications should be sent to the nearest Mercedes-Benz Regional Office listed in the Service and WarrantyInformation Booklet.

Maintenance

The Service Booklet describes all the necessary maintenance work which should be performed at regular intervals.

Always have the Service Booklet with you when you take the vehicle to your authorized Mercedes-Benz Center for service.The service advisor will record each service in the booklet for you.

Roadside assistance

The Mercedes-Benz Roadside Assistance Program provides factory trained technical help in the event of a breakdown. Calls to thetoll-free Roadside Assistance number:

1-800-222-0100 (in the USA) only

will be answered by Mercedes-Benz Client Assistance Representatives 24 hours a day, 365 days a year.

For additional information refer to the Mercedes-Benz Roadside Assistance Program brochure in your glove box.

5

Change of address or ownership

If you change your address, be sure to send in the "Change of Address Notice" found in the Owner's Serviceand Warranty Policy Booklet. It is in your own interest that we can contact you should the need arise.

If you sell your Mercedes, please leave all owner's literature with the vehicle to make it available to the next owner.If you bought this vehicle used, be sure to send in the "Notice of Purchase of Used Car" found in the Owner'sService and Warranty Policy Booklet.

Operating your vehicle outside the USA or Canada

If you plan to operate your vehicle in foreign countries, please be aware that service facilities or replacementparts may not be readily available.

Certain Mercedes-Benz models are available for delivery in Europe under our European Delivery Program.For details, consult your authorized Mercedes-Benz dealer or write to:

In the USA: In Canada:Mercedes-Benz USA, Mercedes-Benz Canada, Inc.LLC European Delivery Department European Delivery DepartmentOne Mercedes Drive 849 Eglinton Avenue EastMontvale, NJ 07645 Toronto, Ontario M4G 2L5

6

We continuously strive to improve our product, and ask for your understanding that we reserve the right to make changes in design andequipment. Therefore, information, illustrations and descriptions in this Operator's Manual might differ from your vehicle.

Optional equipment is also described in this manual, including operating instructions wherever necessary. Since they are special-orderitems, the descriptions and illustrations herein may vary slightly from the actual equipment of your vehicle.

If there are any equipment details that are not shown or described in this Operator's Manual, your authorized Mercedes-Benz Center will be glad to inform you of correct care and operating procedures.

The Operator's Manual and Service Booklet are important documents and should be kept with the vehicle.

7

Check Regularly and Before a Long TripSee Index

The First 1000 Miles (1500 km)

The more cautiously you treat your vehicle during the break-in period, the more satisfied you will be with its performance later on.Therefore, drive your vehicle during the first 1500 km (1000 miles) at moderate vehicle and engine-speeds.During this period, avoid heavy loads (full throttle driving) and high RPM (no more than 2/3 of maximum permissible speed in eachgear as indicated on the speedometer).Avoid accelerating by kickdown. It is not recommended to brake the vehicle by manually shifting to a lower gear. We recommend toselect positions "3" or "2"only at moderate speeds (for hill driving).After 1000 miles (1500 km) speeds may be gradually increased to the permissible maximum

Maintenance

We strongly recommend that you have your vehicle serviced by your authorized Mercedes-Benz dealer, in accordance with theMaintenance Booklet.

Failure to have the vehicle maintained in accordance with the Maintenance Booklet may result in vehicle damage not covered bythe Mercedes-Benz Limited Warranty.

Radio Transmitters

Warning!

Never operate radio transmitters equipped with a built-in or attached antenna (i.e. without the telephoneconnected to an external antenna) from inside the vehicle while the engine is running. Doing so could leadto a malfunction of the vehicle's electronic system, possibly resulting in an accident and personal injury.

Radio transmitters, such as a portable telephone or a citicens band unit should only be used insidethe passenger compartment, if they are connected to a Mercedes-Benz approved antenna that isinstalled on the outside of the vehicle.

8

Introduction Power window and sliding/Pop-Up roof 32 Rear Window Sunshade 67Product information 2 Power closing assist for door and trunk lid 33 Rear Window Defroster 68Operator's manual 4 Anti-Theft Alarm System 34 Shelf Below Rear Window 68Consumer Information 130 Power Seats, Front 35 Setting Clock 69Problems with your vehicle 131 Lumbar support 38 Antenna 69Reporting Safety Defects 132 Multicontour Backrest 38 Cellular Telephone 69Index 134 Heated Seats 39

Armrest, front 40 DrivingInstruments and controls Head Restraints, Rear 42

Power Head Restraints, Rear 43 Drinking and driving 72Instruments and controls 10 Adjustable steering wheel 44 Parking Brake 72

Instrument Cluster 12Seat belts and Supplemental restraintsystem (SRS) 45

Driving off 72

Indicator Lamp Symbols 13 Seat belts 45 Automatic Transmission 73Starting and Turning Off the Engine 14 Emergency tensioning retractor (ETR) 48 Rear Fender Indicator 76Driving Instructions 15 Airbag 49 Cruise Control 76

Steering Lock 54 Charge Indicator Lamp 78Operation Combination Switch 55 Engine Oil Pressure Gauge with Oil

Pressure Warning Lamp 78Air Outlets 20 Exterior Lamp Switch 57 Low Engine Oil Level Warning Lamp 79Automatic Climate Control 21 Inside and exterior Rear View Mirrors 58 Engine Oil Consumption 79Rear passenger compartment

Adjustable Air outlet 24Sun Visors 61 Fuel Consumption Gauge 79

Climate control 25 Vanity mirrors 61 Fuel Reserve Warning Lamp 78Activated Charcoal Filter 25 Interior Lighting 62 Outside Temperature Indicator 80Car keys 26 Storage Compartments 63 Coolant Temperature Gauge 80Infrared Remote Control 27 Ashtrays 64 Low Engine Coolant Level

Warning Lamp81

Central Locking system 30 Lighter 64 Low Windshield andHeadlamp Washer System

Doors 30 Sliding roof with rear pop-up feature 65 Washer Fluid Level Warning Lamp 81Trunk 31 Power Windows 67 Exterior Lamp Failure Indicator Lamp 82

9

Seat Belt Warning Lamp 82 Spare Wheel, lug wrench 93 Emergency Operation of Sliding Roof 118Brake Pad Wear Indicator Lamp 82 Stowing Things in the Vehicle 95 Roof Rack 119Brake Warning Lamp 83 First Aid Kit 95 MERCEDES-BENZ

Spare Parts Service119

ABS (Antilock Brake System)Warning Lamp 84

Vehicle Jack 96 Layout of Poly-V-Belt Drive 119

Automatic Locking Differential (ASD) 85 Vehicle Tools 96Adaptive damping system (ADS) 86 Storage compartment below vehicle tool

box96 Technical Data. Fuels,

Coolants, Lubricants etc. ConsumerInformation

Emission Control 87 Wheels 97

Changing Wheels 98 Identification Plates 122Traveling Abroad 87 Tire in Inflation Pressure 101 Warranty Coverage 123Winter Driving 88 Battery 102 Technical Data 124Snow Chains 88 Exterior Lamps 103 Fuels, Coolants, Lubricants etc. 125

Fuses 107 Capacities 125Practical Hints Jump Starting 108 Engine Oils 127

Towing the Vehicle 110 Brake Fluid 127Hood 90 Cleaning and Care of the Vehicle 111 Air Conditioner Refrigerant 127Checking Coolant Level 91 Testing Infrared Remote Control 114 Diesel Fuels 128Adding Coolant 91 Front Head Restraints 115 Coolants 129Checking Engine Oil Level 92 Rear Seat Cushion 116 Check regularly and before a long trip 139Checking Automatic Trans. Fluid Level 93 Manual Closing of Trunk Lid 116Turning Off Engine Manually 94 Manual Retraction of Trunk Lid Handle 116Blending of Fuel System 94 Replacing Wiper Blades 117Trunk Lamp 95 Manual Release of Fuel Filler Flap 118

10

Instruments and ControlsFor more detailed descriptions see specified pages

1 Adjustable air outlet 19 Storage/eyeglasses compartment2 Exterior lamp switch 20 Lock for storage/eyeglasses compartment and eye glove3 Parking brake release 21 Glove box (illuminated with key in steering lock

position 2)4 Hood lock release 22 Rear window defroster switch5 Parking brake pedal 23 Switch for rear seat head restraints6 Steering wheel adjustment switch 24 Activated charcoal filter switch7 Combination switch 25 Central locking switch8 Cruise control switch 26 Hazard warning flasher switch9 Horn, airbag 27 Automatic climate control10 Instrument cluster 28 Radio11 Steering lock with ignition/starter switch 29 Ashtray with lighter12 Adjustable air outlet 30 Adaptive damping system adjustment switch13 Heated air supply button - center air outlet 31 Seat heater switch

14 Non heated/cooled air supply button - center air outlet 32 Mirror adjustment switch15 Air volume control for left air outlet 33 Switch for rear window sunshade16 Air volume control for left center air outlet 34 Power window switch17 Air volume control for center air outlet 35 Loudspeaker front to rear fader control18 Air volume control for right air outlet

11

12

Instrument Cluster

1 Fuel gauge with reserve warning lamp (yellow). See Index 9 Trip odometer. See Index2 Coolant temperature gauge. See Index 10 Main odometer. See Index3 Fuel consumption gauge. See Index 11 Outside temperature indicator. See Index4 Engine oil pressure gauge (bar) with warning lamp (red).

See Index12 Right turn signal indicator lamp (green) See Index

5 Left turn signal indicator lamp (green). See Index 13 Knob for setting clock (to adjust pull knob outand rotate). See Index

6 Knob for instrument lamps and trip odometer.Rotate knob: To vary intensity of instrument lamps.Depress knob: To reset trip odometer. See Index

14 Tachometer. See Index

7 Speedometer See Index 15 Electric clock. See Index8 ASD function indicator lamp (yellow). See Index ADS function indicator lamp (yellow). See Index

13

Indicator Lamp SymbolsFunction Indicator Lamp

High beam ADS malfunction. See Index

Preglow. See Index ASD malfunction. See Index

Warning Lamp(should go out with the engine running unless)

ABS malfunction. See Index.

Battery not being charged properly. See Index. Brake pads worn down. See Index.

Fluid level for windshield and headlamp washersystem low. See Index.

Brake fluid low (except Canada). Parking brakeengaged. See Index.

Coolant level low. See Index. Brake fluid low (Canada only). Parking brakeengaged. See Index.

Engine oil level low. See Index. SRS malfunction. See Index.

Exterior lamp failure. See Index. Fasten seat belts.See Index.

14

Starting and Turning Off the Engine

Before Starting

Engage parking brake and move theselector lever to position "P" or "N".

Cold Engine

Turn key to steering lock position 2.Charge indicator and pre-glowindicator lamp should come on. Thepreglow process starts. When thepreglow indicator lamp goes out, theengine is ready for starting.

Ambient temperatures above+ 14°F (-10°C):

Do not depress accelerator. Turn key insteering lock clockwise to the stop.Release key only when the engine isfiring regularly.

Ambient temperaturesbelow +14°F(-10°C):

Depress accelerator party. Turn key insteering lock clockwise to the stop.Release key only when the engine isfiring regularly and back offaccelerator slowly.

Do not interrupt the starting process. Ifthe engine is very cold, it is possiblethat it will fail to start on subsequentattempts.

At ambient temperatures below 0°F(-18°C), depress accelerator three timesprior to starting.

Hot Engine

Turn key in steering lock clockwise tothe stop and start engine immediatelywithout depressing the accelerator.

Turning off

Turn the key in the steering lock toposition 0 only when the vehicle hasstopped moving.The key can only be removed with theselector lever in position "P".Should the engine continue to operatewith the key in steering lock position0, refer to Engine, Turning OffManually in Index.

If the coolant temperature is very high(e.g. after hard driving on mountainroads), do not shut off the engineimmediately, allow it to run for 1 - 2minutes at increased idle speed withselector lever in position "P" or "N".

Important!

Due to the installed starter non-repeatfeature, the key must be turnedcompletely to the left before attemptingto start the engine again.

Observe the oil pressure gaugeimmediately after starting the engine.In a very cold engine the oil pressurewill rise slowly. Do not speed up theengine before pressure is registered onthe pressure gauge. If you do not seethe gauge register oil pressure, stop theengine and have it checked.The battery charge indicator lampshould go out as soon as the engine hasstarted.

If the preglow indicator lamp fails tolight up, or lights up while driving, thepreglow system is defective and shouldbe repaired at your authorizedMercedes-Benz dealer at the earliestpossible date.

The engine is equipped with a blockheater to provide reliable starting attemperatures below 0° F (-18°C).Refer to Winter Driving in Index.

15

Driving Instructions

Power Assistance

When the engine is not running, thebrake and steering systems are withoutpower assistance. Under thesecircumstances, a much greater effort isnecessary to stop or steer the vehicle.

Brakes

Caution!

When driving down long and steepgrades, relieve the load on the brakesby shifting into a lower gear (selectorlever position "4" , "3" , "2". This helpsprevent overheating of the brakes andreduces brake pad wear. Do not exceedengine speed limits (see Index).

After hard braking, it is advisable todrive on for some time, rather thanimmediately parking, so the air streamwill cool down the brakes faster.

Warning!

After driving in heavy rain for sometime without applying the brakes orthrough water deep enough to wetbrake components, the first brakingaction may be somewhat reducedand increased pedal pressure maybe necessary. Be sure to maintain asafe distance from vehicles in front.

The condition of the parking brakesystem is checked each time the car isin the shop for the requiredmaintenance.

Between maintenance checks, it is agood practice to apply the parkingbrake once or twice while driving atapproximately 50 km/h (30 mph) on adry straight road. Apply parking brakelightly until a slight drag on the wheelsis felt. Keep applying the brake forabout 10 seconds while pulling the re-lease handle out before releasing theparking brake completely. This practicewill keep the parking brake atmaximum efficiency.

16

Warning!

The stop lamps will not come onwhen applying the parking brakeonly. Perform the procedure in theprevious paragraph only when theroad is clear of other traffic.

Resting your foot on the brake pedalwill cause excessive and prematurewear of the brake pads.

It can also result in the brakesoverheating thereby significantlyreducing their effectiveness. It maynot be possible to stop the car insufficient time to avoid an accident.

All checks and maintenance work onthe brake system should be carried outby an authorized MERCEDES-BENZdealer.

If the parking brake is released and thebrake warning lamp in the instrumentcluster stays on, the brake fluid level inthe reservoir is too low.

Brake pad wear or a leak in the systemmay be the reason for low brake fluidin the reservoir.

Have the brake system inspected at anauthorized MERCEDES-BENZ dealerimmediately.

Install only brake pads and brake fluidrecommended by MERCEDES-BENZ.

Warning!

If other than recommended brakepads are installed, the brakingproperties of the vehicle can beaffected to an extent that the safety issubstantially impaired.

Tires

Tread wear indicators (TWI) arerequired by law. These indicators arelocated in six places on the treadcircumference and become visible at adepth of approx. 2 mm (1/16 in), atwhich point the tire is considered wornand should be replaced.

The tread wear indicator appears as asolid band across the tread.

17

Warning!

Do not allow your tires to weardown too far. With less than 1/8 in (3mm) of tread, the adhesionproperties on a wet road are sharplyreduced.Depending upon the weather and/orroad surface (conditions), the tiretraction varies widely.

Specified tire pressures must bemaintained. This applies particularly ifthe tires are subjected to high loads(e.g. high speeds, heavy loads, highambient temperatures).

Warning!

Do not drive with a flat tire. A flattire affects the ability to steer orbrake the vehicle. You may losecontrol of the car. Continueddriving with a flat tire or driving athigh speed with a flat tire will causeexcessive heat build-up and possiblya fire.

Aquaplaning

Depending on the depth of the waterlayer on the road, aquaplaning mayoccur, even at low speeds and with newtires. Avoid track grooves in the roadarid apply brakes cautiously in the rain.

Tire Traction

The safe speed on a wet, snow coveredor icy road is always lower than on adry road.

You should pay particular attention tothe condition of the road as soon as theprevailing temperatures fall close to thefreezing point.

Warning!

If ice has formed on the road, tiretraction will be substantiallyreduced. Under such weatherconditions, drive, steer and brakewith extreme caution.

We recommend M + S radial-ply tiresfor the winter season for all fourwheels to insure normal balancedhandling characteristics.

On packed snow, they can reduce yourstopping distance as compared withsummer tires. Stopping distance,however, is still considerably greaterthan when the road is wet or dry.

18

Parking

Warning!

To reduce the risk of personal injuryas a result of vehicle movement,before turning off the engine andleaving the vehicle always:

1. Keep right foot on brakepedal.

2. Firmly depress parkingbrake pedal.

3. Move the selector lever toposition "P".

4. Slowly release brake pedal.5. Turn front wheels towards

the road curb.6. Turn the key to steering

lock position 0 and remove.

Important!

It is advisable to set the parking brakewhenever parking or leaving thevehicle. In addition, move selectorlever to position "P".

When parking on hills, always set theparking brake.

Winter Driving Instructions

The most important rule for slippery oricy roads is to drive sensibly and toavoid abrupt acceleration, braking andsteering action. Do not use the cruisecontrol system under such conditions.

When the vehicle is in danger ofskidding move selector lever toposition "N". Try to keep the vehicleunder control by corrective steeringaction.

Road salts and chemicals can adverselyaffect braking efficiency. Increasedpedal force may become necessary toproduce the normal brake effect. Wetherefore recommend depressing thebrake pedal repeatedly when travelingon salt-strewn roads at length. This canbring road salt impaired brakingefficiency back to normal. Aprerequisite is, however, that this ispossible without endangering otherdrivers on the road.

If the vehicle is parked after beingdriven on salt treated roads, the brakingefficiency should be tested as soon aspossible after driving is resumed whileobserving the safety rules in theprevious paragraph.

Warning!

If the vehicle becomes stuck in snow,make sure that snow is kept clear ofthe exhaust pipe and from aroundthe vehicle with engine running.Otherwise, deadly carbon monoxide(CO) gases may enter vehicle interiorresulting in unconsciousness anddeath.

To assure sufficient fresh airventilation, open a window slightlyon the side of the car that is out ofthe wind.

19

Operation

20

Air Outlets

1 Air volume controlfor left air outlet,turn left to open

2 Air volume controlfor left center air outlet, turn left toopen

3 Air volume control.for right center air outlet, turn left toopen

4 Air volume controlfor right air outlet,turn left to open

5 Left center air outlet,adjustable

6 Right center air outlet,adjustable

7 Side air outlet, left and right,adjustable

Push-buttons for center airOutlets

8 Heated air supply(red indicator)

9 Non-heated/cooled air supply(blue indicator)

Basic mode:None of the push-buttons (8 or 9)is pressed.

Note:

Dust particles (down to a certain size)and pollen are filtered out beforeoutside air enters the passengercompartment through the airdistribution system.

21

Automatic Climate Control

Left side passenger compartment:

1 Temperature selector

2 Temperature display

3 Automatic mode

4 Air distribution buttons

5 Defrost

6 Residual engine heatutilization

7 Air recirculation

8 Air volume selector

9 Economy

10 Selection switch

11 Off

Right side passengercompartment:

12 Temperature selector

13 Temperature display

14 Automatic mode

15 Air distribution buttons

22

The temperature selected with thetemperature selector is reached asquickly as possible.

The temperature selector should be leftat the desired temperature setting.With the center air outlets open and thesystem in heating mode, switch theoutlets to non-heated/ cooled air bypressing the blue button (indicator lamplights up).

With the center air outlets open and thesystem in cooling mode, switch theoutlets to non-heated/ fresh air bypressing the red button (indicator lamplights up).

The system will not heat or cool anyquicker by setting a higher or lowertemperature.

The automatic climate control onlyoperates with the engine running.The automatic climate control removesconsiderable moisture from the airduring operation in the cooling mode. Itis normal for water to drip on theground through ducts in the underbody.

1, 12 Temperature Selector

The desired interior temperature can beselected separately for the left and rightside of the passenger compartment.

A basic setting in the white field of theselector is recommended, and can beused for driving year round.

The selected temperature can be shownin the display window (2) in either °For °C.

3, 14 Automatic Mode

This is the normal setting.Air volume and distribution arecontrolled automatically.

To select: Press button(indicator lamp lights up).

To change selection:

Press, , , orbutton (indicator lamp of selected

button lights up). The indicator lampfor button goes out.

Note:

If the Automatic Climate Control is inthe "Diagnosis Mode", turn key insteering lock to position 0 to return itto its normal operation.

5 Defrost

Maximum heated and automaticallycontrolled amount of air is directed tothe windshield and side windows.As the engine coolant temperatureincreases, the air volume isautomatically increased, therebydefrosting as quickly as possible.Open and direct air outlets (7) towardsthe side windows.

Note:Press once again to return toprevious setting.

Defogging Windows

Switch off, or switch on(left and right side), or switch on.

Note:To quickly defog the inside of thewindshield, select the largest airvolume and air distribution button .

23

6 Residual Engine HeatUtilization

With the engine switched off, it ispossible to continue heating the interiorfor a short while. The rear passengercompartment air outlet must be closed.

Air volume and distribution arecontrolled automatically.

To select:

Turn key in steering lock to position1 or 0 or remove key.

Press button (indicator lamp lightsup). This function selection will notactivate if the engine coolanttemperature is below 40°C (105°F) orif the battery charge is insufficient.

To cancel:

• Press button(indicator lamp goes out).

• Turn key in steering lock toposition 2.

The system will automatically shut off

• after approx. 30 minutes,• if the engine coolant temperature

drops below 122°F (50 °C),• if the battery voltage drops.

7 Air Recirculation

Outside air is not supplied to the car'sinterior.

This mode can be selected to preventannoying odors or dust from enteringthe car's interior.

To select: Press button(indicator lamp lights up).

To cancel:Press button (indicator lampgoes out).

The system will automaticallyswitch from recirculated air to freshair if button is pressed

• after approx. 5 minutes atoutside temperatures belowapprox. 40°F(5°C),

• after approx. 20 minutes, atoutside temperatures aboveapprox. 40°F(5°C).

If button is pressed:

• after approx. 5 minutes.

Notes:

If the windows should fog up from theinside, switch from recirculated air backto fresh air.

At high outside temperatures, thesystem automatically engages therecirculated air mode therebyincreasing the cooling capacityperformance, switching to partially freshair within 20 minutes.

24

8 Air Volume Selector

The air volume is automaticallyregulated in

AUTO = Normal setting

and all intermediate positions, exceptwhen selecting

MIN = minimum air flow,MAX = maximum air flow.

9 Economy

The function of this settingcorresponds to the automatic mode.However, because the air conditioningcompressor will not engage (fuelsavings), it is not possible to aircondition in this setting.

12 Off

The fresh air supply to the car interioris shut off.

While driving, use this setting onlytemporarily, otherwise the windshieldcould fog up.

Important!

This vehicle is equipped with an airconditioner system that uses HFC-134a(ozone-friendly hydro-fluorocarbon) as arefrigerant.

Repairs should always be performed bya qualified technician, and refrigerantshould be collected in a recovery systemfor recycling.

Rear Passenger CompartmentAdjustable Air Outlet

Slide switch (1) up to open outlet forfresh/cooled air only.

25

Rear Passenger CompartmentClimate Control

1 Temperature selector, left side2 Temperature selector, right side

A basic setting in the white field of theselector is recommended.

3 Air volume selector

The air volume can be variedcontinuously. The air flow is switchedoff with selector in position "0".

4 Adjustable air outlet, left side5 Adjustable air outlet, right side6 Air distribution slide

Top position: air flow from airoutlets (4 and 5). Bottom position:air flow from air outlets beneathfront seats.

Intermediate positions can beselected for a mixed air flow.

Note:

The rear passenger climate controldoes not operate with automaticclimate control in mode orswitched off with button .

Activated Charcoal Filter

1 Switch on2 Switch offAn activated charcoal filter markedlyreduces bad odors and removespollutants from the air entering thepassenger compartment.When pressing button or ,the filter is also switched off.Note:The activated charcoal filter should beswitched off when windows fog up onthe inside, or if the passengercompartment needs to be quicklyheated up or cooled down.

26

Car Keys

Included with your vehicle are• 2 Master keys with infrared

remote control• 1 Master key• 1 Valet key• 1 Flat key

Infrared Remote Control withFolding Master Key

The master key fits all locks on the car.

The transmitter for the infrared remotecontrol is located in the key holder, thereceivers are located next to the doorlocks and below the trunk lock.

Master Key

The master key fits all locks on the car.

Valet Key

The valet key fits only the door locksand the steering lock.

The valet key will not fit the trunklock or storage compartmenteyeglasses compartment lock in thedashboard.

Flat Key

The flat key fits all locks on the Car.

Note:

Do not give the master key to anunauthorized person.

We recommend that you carry the flatkey with you and keep it. in a safeplace (e.g. your wallet) so that it isalways handy. Never leave the flat keyin the vehicle.

Warning!

When leaving the vehicle alwaysremove the key from the steeringlock. Do not leave childrenunattended in the vehicle.Unsupervised use of vehicleequipment may cause seriouspersonal injury.

Obtaining Replacement Keys

Your vehicle is equipped with a theftdeterrent locking system requiring aspecial key manufacturing process. Forsecurity reasons, replacement keys canonly be obtained via your authorizedMERCEDES-BENZ dealer.

27

Master Key in Key Holder

1 Release button for master key

Releasing: press release button (1). Thekey unfolds from the holder by itself.

Storing: press release button (1) andfold key back into holder.

Infrared Remote Control

1 Transmit button

2 Transmitter eye and battery check

The vehicle can be centrally lockedand unlocked, as well as the windowsand sliding roof closed with infraredremote control.

The transmitter is located in the keyholder; the receivers are locatednext to the door locks and below thetrunk lock.

3 Receiver in door handle

Unlocking:

Aim transmitter eye (2) at a receiver(3) and press transmit button (1).Distance to receiver max. 20 ft (6 m).

The green indicator lamps on thereceivers should blink. They stopblinking when the vehicle isunlocked.

Note:If the trunk was previously lockedseparately, it will remain locked(see Index).

28

3 Receiver next to trunk lock

Locking:

Aim transmitter eye (2) at a receiver(3) and press transmit button (1).Distance to receiver max. 20 ft (6 m).

The red indicator lamp on the receivershould blink. It stops blinking afterapproximately 3 seconds when thevehicle is properly locked.

Notes:

If a door or the trunk is not properlyclosed after you attempt to lock thevehicle by remote control, the redindicator lamps will continue to blink(max. 10 seconds). Open the door ortrunk lid, close it properly, and' lockthe car again.

If the vehicle cannot be locked orunlocked by pressing the transmitbutton (1), then it may be necessary tochange the batteries in the transmitter(if ok, battery indicator lamp intransmitter will light whentransmitting) or to synchronize thesystem, see Testing Infrared RemoteControl in Index.

29

Closing Windows and Sliding/ Pop-Up Roof from Outside

Continue to press transmit button (1)after locking car. Distance to receivermax. 20 ft. (6 m).

The windows and sliding/pop-up roofbegin to close after approx. 1 second.

Warning!

Never close the windows orsliding/pop-up roof if there is thepossibility of anyone being harmedby the closing procedure.

In case the closing procedure causespotential danger, the closingprocedure can be immediatelyreversed by releasing and pressingthe remote control button again untilthe green indicator lamp at thereceiver blinks. The sliding/pop-uproof and windows will open again.The sliding/pop-up roof will onlyopen if it was not fully closed.

Note:

If the side windows and sliding/ pop-uproof cannot be opened automatically byusing the key or by pressing thetransmit button of the infrared remotecontrol (e.g. after a battery change),press side of power windowswitch in center console until thewindow is completely closed and holdfor additional 2 seconds. Repeatprocedure for each window.

The automatic closing procedure of thewindows and sliding/pop-up roofshould now be restored.

30

Central Locking System

The entire vehicle may be locked orunlocked by either using the masterkey in the door or trunk locks, orcentral locking switch located in centerconsole. The central locking systemalso locks or unlocks the fuel filler flap.

Note:

If the fuel filler flap cannot be opened,refer to Fuel Filler Flap, ManualRelease (see Index).

Doors

1 Opening - pull handle2 Unlocking3 Locking4 Individual door from inside:

• Push lock button down tolock.

• Pull lock button up to unlock.

Central locking switch

When you lock the car, all door lockbuttons should move down. If any onestays up, the respective door is notproperly closed.

You should then unlock the car, openand reclose this door, and lock the caragain. Each individual door can belocked with door lock button - thedriver's door can only be locked whenit is closed.

31

The doors can only be locked with thecentral locking switch, if the frontdoors are closed.

The doors cannot be unlocked with thecentral locking switch, if car waspreviously locked from outside.

The entire car is unlocked with thecentral locking switch, if a front door isopened.

If the car has previously been lockedfrom the outside, only the door beingopened from the inside will unlock, theremaining doors, the trunk lid and fuelfiller flap remain locked. 1 Neutral position -

push to open2 Unlocking3 Locking (detent)4 Separate locking of trunk -

remove key in this position.

When the trunk is separatelylocked, it remains locked whenunlocking any door.

To deny any unauthorized personaccess to the trunk, lock itseparately. Leave only the valetkey with the vehicle.

Notes:

In case of a malfunction in the centrallocking system the doors and trunk canbe locked and unlocked individually.To lock, turn key to position 3 or pushdown lock buttons.

To unlock, turn key to position 2 orpull up lock buttons.

The trunk lid can be lowered by usingthe recessed grips in the trunk lid liner,and closed with the dirt-free retractinghandle.

If the trunk lid cannot be closed, referto Trunk Lid, Manual Closing (seeIndex).

32

Door lock, left and trunk lock

Power Windows and Sliding/Pop-Up Roof

1 Closing2 Interrupting3 Opening

Door lock, right

When locking doors or trunk, turn keyin door lock or trunk lock to position 1and hold. The windows and thesliding/pop-up roof begin to closeautomatically after approximately 1second.

To interrupt the closing procedure, turnkey to position 2.

Warning!

Never close the windows orsiding/pop-up roof if there is thepossiblity of anyone being harmed bythe closing procedure.

In case the closing procedure causespotential danger, the closingprocedure can be immediatelyreversed by turning the key to theunlocking position (3) within 10seconds. The sliding/pop-up roof andwindows will open again. Thesliding/pop-up roof will only open ifit was not fully closed.

Note:

If the closing procedure is interrupted,it can only be continued by first turningthe key to the unlocked position (3) andthen again to the locking position (1)and hold.

33

Power Closing Assist for Doors andTrunk Lid

The doors and trunk lid closeautomatically if:

• doors are pushed against the lock,• trunk lid is lowered against the lock.

It is not necessary to slam doors ortrunk lid closed, a pneumatic power-assisted mechanism will latch doorsand trunk lid quietly and automaticallyonce the lid or door has been broughtto a close. When the pneumatic power-assisted mechanism has stopped,doors and/or trunk can be reopened.

Note:

If the trunk lid does not close, refer toTrunk Lid, Manual Closing in Index.

Warning!

To prevent possible personal injury,always keep hands and fingers awayfrom the door or trunk openingwhen closing a door or the trunklid. Be especially careful when smallchildren are around.

The pneumatic power closing assistmechanism cannot be interruptedonce it has been engaged.

To prevent personal injury, neveractivate the closing assistmechanism by tampering with thedoor or trunk lidlatch.

34

1 Indicator lamp in switch located incenter console

Anti-Theft Alarm System

The anti-theft alarm is automaticallyarmed or disarmed with any of yourvehicle's keys or infrared remotecontrol by locking or unlocking eitherfront door or the trunk.

A blinking lamp (1) indicates that thealarm is armed. Now the engine cannotbe started.

The anti-theft alarm is disarmed whenunlocking either front door or the trunkwith any of your vehicle's keys orinfrared remote control.

Operation

Once the alarm system has beenarmed, the exterior vehicle lamps willflash and the horn will soundintermittently when someone:

• opens a door,• opens the trunk,• opens the hood,• removes the radio,• switches on or bridges the ignition

circuit,• steps on the brake pedal.

The alarm will last approximately 150seconds in the form of blinking exteriorlamps. At the same time an alarm hornwill sound intermittently for 60seconds, pause for 30 seconds, andrepeat for another 60 seconds.The alarm will stay on even if theactivating element (a door, forexample) is immediately closed.

Note:

We recommend that you carry the flatkey safely with you so that it is alwayshandy. The flat key has the samefunctions as the master key.

35

Power Seats, Front

The slide switches are located in eachfront door.

Turn key in steering lock to position 1or 2 (with the driver's or frontpassenger's door open, the powerseats can also be operated with the keyremoved or in steering lock position 0).

Seat and head restraint adjustment:

A Seat, fore/aft, up/down

B Seat tilt

C Seat cushion depth

D Backrest tilt

E Head restraint Adjust head restraintto support the back of the headapproximately at ear level. The headrestraint inclination can also beadjusted manually.

Note:

Your car is equipped with powerhead restraints, do not try to raise orlower them manually.

Warning!

Do not adjust the driver's seat whiledriving. Adjusting the seat whiledriving could cause the driver to losecontrol of the vehicle.

Never ride in a moving vehicle withthe seat back reclined. Sitting in anexcessively reclined position can bedangerous. You could slide under theseat belt in a collision. If you sideunder it, the belt would apply forceat the abdomen or neck. That couldcause serious or even fatal injuries.The seat back and seat belts providethe best restraint when the wearer isin an upright position and belts areproperly positioned on the body.

Never place hands under seat ornear any moving parts while a seat isbeing adjusted.

36

F Memory button

G Position buttons

Storing seat/head restraint/ steeringwheel/exterior and inside rear viewmirror positions in memory:

Three sets of seat/head restraint/steering wheel/exterior and inside rearview mirror positions may beprogrammed into memory. After theseat/head restraint/steeringwheel/exterior and inside rear viewmirrors are positioned, push memorybutton F, release, and within 3 secondspush position button "1". A second andthird set of positions for the sameseat/ head restraint/steering wheel/exterior and inside rear view mirrorscan be programmed into memory bypushing first button "F" and then "2",respectively "3".

Note:

See Index for instructions onadjustment of steering wheel andmirrors.

Recalling seat/head restraint/ steeringwheel/exterior and inside rear viewmirror positions stored in memory:

To recall a seat/head restraint/steering wheel/exterior and inside rearview mirror position, push and holdposition button "1", "2" or "3" untilseat/head restraint/ steeringwheel/exterior and inside rear viewmirror movement has stopped. Theseat/head restraint/ steeringwheel/exterior and inside rear viewmirror movement stops when theposition button is released.

Caution!

Do not remove head restraints exceptwhen mounting seat covers. Forremoval and installation refer to HeadRestraints, Removal in Index.Whenever restraints have beenremoved be sure to reinstall thembefore driving.

37

Important!

Bring seat backrest to upright positionbefore recalling a stored seat/headrestraint/steering wheel/exterior andinside rear view mirror position,otherwise the front seats could getforced against a rear seat and bedamaged.

Prior to operating the vehicle, thedriver should adjust the seat height forproper vision as well as fore/aftplacement and seat back angle to insureadequate control, reach, operation, andcomfort. The head restraint should alsobe adjusted for proper height.

Both the inside and outside rearview mirrors should be adjusted foradequate rearward vision.

Fasten seat belts. Infants and smallchildren should be seated in a properlysecured restraint system that complieswith U.S. Federal Motor VehicleSafety Standard 213 and CanadianMotor Vehicle Safety Standard 213.1.

All seat, head restraint, and rear viewmirror adjustments as well as fasteningof seat belts should be done before thevehicle is put into motion.

38

Lumbar Support1 Pressure regulator

The seats have an inflatable aircushion built into the backrest toprovide additional lumbar support.The inflation pressure of the aircushion can be continuously variedbetween position "0" = withoutpressure, and position "5" = maximumpressure, by changing the pressureregulator (1) setting.

Multicontour Backrest

1 Height regulator2 Pressure regulator3 Side bolster adjustment

The seats have inflatable air cushionsbuilt into the backrest to provideadditional lumbar and side support.The amount of cushion height andcurvature may be adjusted after turningthe key in steering lock to position 2.

BottomCenterTop

can be selected together withor

The inflation pressure of the aircushion can be continuously variedbetween position "0" = withoutpressure, and position "5" = maximumpressure, by changing the pressureregulator (2) setting.

The side bolsters of the backrest canbe adjusted with push button (3):

• pushing forward -increase side support,

• pushing backward -decrease side support.

If the engine is turned off, the lastcushion setting is retained in memory,and automatically adjusts the cushionto this setting when the engine isrestarted.

39

Heated Seats

The front seat heater switches arelocated to the left and right side of thecenter console ashtray.

The rear seat heater switches arelocated in each rear door.

The front seat heaters can be switchedon with the key in steering lockpositions 1 or 2, the rear seat heatersonly in steering lock position 2.

Press switch to turn on heater:

1 Normal heating mode. Oneindicator lamp in the switchlights up.

2 Rapid heating mode. Bothindicator lamps in the switchlight up.After approximately 5 minutes inthe rapid heating mode, the heaterautomatically switches to normaloperation and only one indicatorlamp will stay on.

Turning off heater:

If one indicator lamp is on, pressupper half of switch.

If both indicator lamps are on,press lower half of switch.

If left on, the heater automaticallyturns off after approximately 30minutes of operation.

Note:

When in operation, the seat heaterconsumes a large amount of power. Itis advisable not to use the seat heaterlonger than necessary.

The seat heaters may automaticallyswitch off if too many power consumersare switched on at the same time, or ifthe battery charge is low. When thisoccurs, the indicator lamp in the switchwill blink (both indicator lamps blinkduring rapid seat heating). The seatheaters will switch on againautomatically as soon as sufficientvoltage is available.

If the blinking of the indicator lamps isdistracting to you, the seat heaters canbe switched off.

40

Armrest with Compartmentfor Telephone Handset(Front Seats)

1 Armrest folded down2 Normal use

(3 comfort positions)3 Armrest folded up

Folding down:

Raise armrest past top comfort positionand push down.Adjusting height:

Raise armrest to desired position.

Press button (4) to open cover.

Note:

The cover cannot be opened witharmrest raised above the top comfortposition.

Warning!

The armrest does not suffice as achild restraint system. In case of afrontal collision a child can becatapulted forward over the lockedarmrest. Infants and small childrenshould always be seated in aproperly secured restraint systemthat complies with U.S. FederalMotor Vehicle Safety Standard 213and Canadian Motor Vehicle SafetyStandard 213.1.

41

.

Power Seats, Rear

The seats can be adjusted using theslide switches located in either of therear doors.

Turn key in steering lock to position1 or 2 (with the driver's or frontpassenger's door open, the power seatscan also be operated with the keyremoved or in steering lock position 0).

Seat Bench

1 Backrest tilt

Individual Seats

1 Backrest tiltThe seat cushion moves fore/afttogether with the inclination of thebackrest.

2 Seat tilt

42

Armrest with Integrated StorageCompartment (Rear Bench Seat)

Pull down the armrest by its strap.Before storing the armrest in thebackrest, close its storage com-partment lid.

For the removal of the Rear SeatCushion, see Index.

Head Restraints, Rear(Vehicles without rear power seats)

Turn key in steering lock toposition 1 or 2.

Press symbol-side of rocker switch torelease the head restraints. The headrestraints will then fold backward forincreased visibility.

Placing head restraints upright:Pull head restraint forward by its strapuntil it locks in position.inclination of head restraints:The head restraint inclination can beadjusted manually.

Important!

For safety reasons, always drive withthe rear head restraints in the uprightposition when the rear seats areoccupied.

Keep area around head restraints clearof articles (e.g. clothing) to not obstructthe folding operation of the headrestraints.

43

Switch on center console

Power Head Restraints, Rear

Turn key in steering lock to position 1or 2 (with the driver's or frontpassenger's door open, the power headrestraints can also be operated with thekey removed or in steering lock position0).

Activate switch:1 Place head restraint upright.2 Fold head restraint backward.

Switches in rear doorsSwitch in center console:

Both head restraints together can beplaced in either upright or fold-downposition.

Switches in rear doors:The head restraints can be placedindividually in either upright or fold-down position.

Inclination of head restraints:The head restraint inclination can beadjusted manually.

Important!

For safety reasons, always drive withthe rear head restraints in the uprightposition when the rear seats areoccupied.

Keep area around head restraints clearof articles (e.g. clothing) to not obstructthe folding operation of the headrestraints.

44

Adjustable Steering Wheel

Turn key in steering lock to position 1or 2 (with the driver's or frontpassenger's door open, the steeringwheel can also be operated with thekey removed or in steering lockposition 0).

To lengthen or shorten the steeringcolumn, push in or pull out switch (1).

To raise or lower steering wheel, pushswitch (1) up or down.

Note:

The steering wheel position can bestored in memory together with theseat/head restraint/exterior andinside rear view mirror positions, seeIndex.

Warning!

Do not adjust the steering wheelwhile driving. Adjusting thesteering wheel while driving couldcause the driver to lose control ofthe vehicle.

45

Seat Belts and SupplementalRestraint System (SRS)

Your vehicle is equipped with lap-shoulder seat belts, emergencytensioning retractors for the seat belts,driver airbag and knee bolster andpassenger airbag and knee bolster.

Seat Belts

Important!

Laws in most states and all Canadianprovinces require seat belt use.All states and provinces require use ofchild restraints that comply with U.S.Federal Motor Vehicle Safety Standard213 and Canadian Motor VehicleSafety Standard 213.1.

We strongly recommend their use.

Warning!

Never ride in a moving vehicle withthe seat back reclined. Sitting in anexcessively reclined position can bedangerous. You could slide underthe seat belt in a collision. If youslide under it, the belt would applyforce at the abdomen or neck. Thatcould cause serious or even fatalinjuries. The seat back and seatbelts provide the best restraintwhen the wearer is in an uprightposition and belts are properlypositioned on the body.

Seat Belt Warning System

With the key in steering lock position2, an audible warning sounds for a shorttime if the driver's seat belt is notfastened.

If you are ever in an accident, yourinjuries can be considerably moresevere without your seat beltproperly buckled. Without your seatbelt buckled, you can hit theinterior of the vehicle or be ejectedfrom it. You can be seriously in-jured or killed.

In the same crash, the possibilityfor injury or death is lessened withyour seat belt buckled.

46

1 Latch plate2 Buckle3 Release button

Fastening of Seat Belts

Push latch plate (1) into buckle (2)until it clicks.

The lap belt should be positioned aslow as possible on your hips and notacross the abdomen.Three-point seat belt:Tighten the lap portion to a snugfit by pulling shoulder portion up.Rear center seat belt: Tighten to a snugfit by feeding belt toward retractor.

Adjust seat belt so that shoulderportion is located as close as possibleto the middle of your shoulder. Do nottwist the belt.

The shoulder portion of the seat beltmust be pulled snug and checked forsnugness immediately after engagingit.The height setting for the shoulderportion of the front seat belts areautomatically adjusted by the fore/ aftmovement of the front seat.Seat moved to front: Belt outlet fullylowered.Seat moved to rear: Belt outlet fullyraised.

For safety reasons, avoid adjusting theseat or seat back into positions whichcould affect the correct seat beltposition.

Unfastening of Seat Belts

Push the release button (3) in the beltbuckle (2).

Allow the retractor to completelyrewind the seat belt by guiding thelatch plate (1).

Notes:The rear seat belt buckles can be storedin the space next to the rear armrest (tothe left and right of armrest). The rearcenter seat belt should be latched andstored under the armrest.

For cleaning and care of the seat belts,see Upholstery in Index.

Operation:The inertia reel stops the belt fromunwinding during sudden vehicle stopsor when quickly pulling on the belt.

The locking function of the reel maybe checked by quickly pulling out thebelt.

47

Warning!

USE SEAT BELTS PROPERLY.

• Each occupant should wear theirseat belt at all times. Togetherwith the "SRS", the seat beltoffers the best conditions forprotection of the body in case ofmajor frontal impact.

• Improperly positioned seat beltsdo not provide maximumprotection and may cause seriousinjuries in case of an accident.

• Never wear the shoulder beltunder your arm, against yourneck or off your shoulder. In acrash, your body would move toofar forward. That would increasethe chance of head and neckinjuries. The belt would alsoapply too much force to the ribs,which could severely injureinternal organs such as your liveror spleen.

• Position the lap belt as lowas possible on your hips and notacross the abdomen. If the belt ispositioned across your abdomen,it could cause serious injuries in acrash.

• Each seat belt should never beused for more than one person ata time.

• Belts should not be worn twisted.In a crash, you wouldn't have thefull width of the belt to takeimpact forces. The twisted beltagainst your body could causeinjuries.

• Pregnant women should also use alap-shoulder belt. The lap beltportion should be positioned aslow as possible on the hips toavoid any possible pressure onthe abdomen.

USE CHILD RESTRAINTSPROPERLY.

• Infants and small children mustbe seated in an infant or childrestraint system,

which is properly secured by a lapbelt or lap belt portion of a lap-shoulder belt. Children could be endangered in an accident if theirchild restraints are not properlysecured in the vehicle.

• Rear-facing child restraints mustnot be used in the front seat witha passenger side airbag. Theycould be struck by the airbagwhen it inflates in a crash. If thishappens, a child in the restraintcould be seriously injured.

• According to accident statistics,children are safer when properlyrestrained in the rear seatingpositions than in the front seatingpositions.

• Children too big for childrestraint systems should useregular seat belts. Positionshoulder belt across chest andshoulder, not face or neck. Abooster seat may be necessary toachieve proper belt positioning.

48

Supplemental Restraint System(SRS)

The SRS uses two crash severity levels(thresholds) to activate either the ETRor airbag or both. Activation dependson exceeding the thresholds andfastening of the seat belt.

Seat belt fastened

• first threshold exceeded:ETR activates

• second threshold exceeded:airbag also activates

Seat belt not fastened

• first threshold exceeded: airbagactivates, but not ETR

Driver and front passenger systemsoperate independently from each other.

Emergency TensioningRetractor (ETR)

The seat belts are equipped withemergency tensioning retractors. Thesetensioning retractors are located in eachbelt's inertia reel and becomeoperationally ready with the key insteering lock position 1 or 2.

The emergency tensioning retractorsare designed to activate only when theseat belts are fastened during majorfrontal impacts within the shaded areashown. They tighten the belts in such away that they fit more snugly againstthe body, restricting its forwardmovement as much as possible.

In cases of other frontal impacts, roll-overs, certain side impacts, rearcollisions, or other accidents withoutfrontal forces, the emergencytensioning retractors will not beactivated. The driver and passengerwill then be protected by the fastenedseat belts and inertia reel in the usualmanner.

For seat belt and emergency tensioningretractor safety guidelines, see SafetyGuidelines in Index.

49

Airbags

The most effective occupant restraintsystem yet developed for use inproduction vehicles is the three pointseat belt. In some cases, however, theprotective effect of a seat belt can befurther enhanced by an airbag.

The driver airbag (1) is located in thesteering wheel hub. The passengerairbag (2) is located in the dashboardahead of the passenger. In conjunctionwith wearing the seat belts withemergency tensioning retractors (4),they provide increased protection forthe driver and passenger.

The operational readiness of the airbagsystem is verified by the indicatorlamp "SRS" (3) in the instrumentcluster. If no fault is detected, the lampwill go out after approximately 4seconds; after the lamp goes out, thesystem continues to monitor thecomponents and circuitry of the airbagsystem and will indicate a malfunctionby coming on again.

50

The following system components aremonitored or undergo a self-check:crash-sensor, airbag ignition circuits,driver and passenger seat belt buckles.Initially, when the key is turned fromsteering lock position 0 to positions 1 or2, malfunctions in the crash-sensor aredetected and indicated (the "SRS"indicator lamp stays on longer than 4seconds).

In the operational mode, after theindicator lamp has gone out followingthe initial check, interruptions and shortcircuits in the airbag ignition circuit andin the driver and passenger seat beltbuckle harnesses, and low voltage in theentire system are detected andindicated.

In the event a malfunction of the "SRS"is indicated as outlined above, the"SRS" may not be operational. Westrongly recommend that you visit anauthorized MERCEDES-BENZ dealerimmediately to have the systemchecked; otherwise the "SRS" may notbe activated in a major frontal accident.

Important!

The airbags are designed to activateonly in certain frontal and front-angled impacts (within the shadedarea shown in the illustration onpage 44). Only during these types ofimpacts will they provide theirsupplemental protection. The driverand passenger should always wearthe seat belts; otherwise it is notpossible for the airbags to providetheir intended supplementalprotection.

In cases of other frontal impacts,roll-overs, certain side impacts, rearcollisions, or other accidents withoutfrontal forces, the airbag will not beactivated. The driver and passengerswill then be protected by the fastenedseat belts.

51

Important!

The "SRS" is designed to reduce thepotential of injury in certain frontaland front-angled impacts which maycause injuries; however, no systemavailable today can totally eliminateinjuries and fatalities.

The activation of the "SRS"temporarily releases a small amountof dust from the air-bags. This dust,however, is neither injurious to yourhealth, nor does it indicate a fire inthe vehicle.

The service life of the airbagsextends to the date indicated on thelabel located on the driver-side doorlatch post To provide continuedreliability after that date, they shouldbe inspected by an authorizedMERCEDES-BENZ dealer at thattime and replaced when necessary.

Warning!

It is very important for your safetyto always be in a properly seatedposition.

For maximum protection in theevent of a collision always be innormal seated position with yourback against the seat back. Fastenyour seat belt and ensure that it isproperly positioned on the body.

Since the airbag inflates withconsiderable speed and force, aproper seating position will keepyou in a safe distance from theairbag:

• Sit properly belted in anupright position with yourback against the seat back.

• Do not lean with your heador chest close to the steeringwheel or dashboard.

• Adjust the passenger seatas far as possible rearwardfrom the dashboard,especially when a childrestraint is installed.

• Infants and small childrenshould only be seated in aninfant or child restraintwhich is properly securedby the seat belt.

• Rear-facing child restraintsmust not be used in a frontseat.

Failure to follow these instructionscan result in severe injuries to you orother occupants.

52

Safety Guidelines for the Seat Belt,Emergency Tensioning Retractorand Airbag

Warning!

• Damaged belts or belts that werehighly stressed in an accidentmust be replaced and theiranchoring points must also bechecked. Use only belts installedor supplied by an authorizedMercedes-Benz dealer.

• Do not pass belts over sharpedges.

• Do not make any modificationthat could change theeffectiveness of the belts.

• The "SRS" is designed tofunction on a one-time-onlybasis. An airbag or emergency

tensioning retractor (ETR) thatwas activated must be replaced.

• No modifications of any kindmay be made to any componentsor wiring of the "SRS". Thisincludes the installation ofadditional trim material, badgesetc. over the steering wheel hubor front passenger airbagcover and installation ofadditional electrical/electronicequipment on or near "SRS"components and wiring.

• Several airbag systemcomponents at the steeringwheel get hot after the air-bag has inflated. Don't try totouch them.

• Improper work on the system,including incorrect installationand removal, can lead to possibleinjury through an uncontrolledactivation of the "SRS".

• In addition, through improperwork there is the risk ofrendering the "SRS"inoperative. Work on the "SRS"must therefore only beperformed by an authorizedMercedes-Benz dealer.

• When scrapping the airbagunit or emergency tensioningretractor, it is mandatoryto follow our safety instructions. These instructions areavailable at your authorizedMercedes-Benz dealer.

When you sell the vehicle we stronglyurge you to give notice to the subsequentowner that it is equipped with an "SRS"by alerting him to the applicable sectionin the Owner's Manual.

53

Infants and Child RestraintSystems

We recommend that all infants andchildren be restrained at all times whilethe vehicle is in motion.

Important!

The use of infant or child restraints isrequired by law in all 50 states and allCanadian provinces.

Infants and small children should beseated in an infant or child restraintsystem, which is properly secured bythe lap belt portion of the lap-shoulderbelt, and that complies with U.S.Federal Motor Safety Standard 213 andCanadian Motor Vehicle SafetyStandard 213.1.A statement by the child restraintmanufacturer of compliance with thisstandard can be found on theinstruction label on the restraint and inthe instruction manual provided withthe restraint.

When using any infant or childrestraint system, be sure to carefullyread and follow all manufacturer'sinstructions for installation and use.

Warning!

According to accident statistics,children are safer when properlyrestrained in the rear seatingpositions than in the front seatingpositions.

Rear-facing child restraints must notbe used in a front seat with apassenger side airbag. They could bestruck by the airbag when if inflatesin a crash. If this happens, a child inthe restraint could be seriouslyinjured.

Infants and small children shouldnever be held on the lap while thevehicle is in motion. During anaccident they would be almost impos-sible to hold, and could be crushedbetween the adult and the dashboard.

Infants and small children shouldnever share a seat belt with anotheroccupant. During an accident, theycould be crushed between theoccupant and seat belt.

Children too big for child restraintsystems should use regular seat belts.Position the shoulder belt across thechest and shoulder, not the face orneck. A booster seat may benecessary to achieve proper beltpositioning.

When the child restraint is not inuse, remove it from the car orsecure it with the seat belt toprevent the child restraint frombecoming a projectile in the event ofan accident.

U.S.A. Models onlySince 1986 all U.S. child restraintscomply with U.S. regulations withoutthe use of a tether strap.

Canada Models only

This vehicle can be equipped withtether anchorages for a top tether strap.Consult your authorized Mercedes-Benz dealer for installation of theseanchorages.

In compliance with Canadian MotorVehicle Safety Standard 210.1, childrestraint tether anchorage hardwareis attached to the tool kit located inthe trunk.

54

Steering Lock

0 The key can be withdrawn in thisposition only. The steering islocked with the key removedfrom the steering lock. The keycan be removed only with theselector lever in position "P".After removing the key or withthe key in steering lock position 0,the selector lever is locked inposition "P".

1 Steering is unlocked.(If necessary, move steering wheelslightly to allow the key to beturned clockwise to position 1.)Most electrical consumers can beoperated. For detailed informationsee respective subjects.

2 Driving position.3 Starting position.

Refer to Index for Starting and turningoff engine.

Warning!When leaving the vehicle alwaysremove the key from the steeringlock. Do not leave childrenunattended in the vehicle.Unsupervised use of vehicleequipment may cause seriouspersonal injury.

Notes:

The following items can be operatedwith the key in steering lockposition 1:

wiper,headlamp flasher,lighter,glove box lamp,sound system (also in position 0),sliding roof,

rear window defroster,power windows,power seats, front,heated seats, front,adjustable steering wheel.

An audible warning will sound whenthe driver's door is opened with the keyin steering lock position 1 or 0.

With the engine at idle speed, thecharging rate of the alternator (output)is limited.

It is therefore recommended to turn offunnecessary electrical consumers whiledriving in stop-and-go traffic. Thisprecaution helps to avoid draining ofthe battery.

Unnecessary strain on the battery andcharging system may be minimized byturning off the following powerconsumers, for example: Heated seats,rear window defroster. In addition, theautomatic climate air volume controlshould be set to "MIN".

55

Combination Switch

1 Low beam (exterior lampswitch position )

2 High beam (exterior lampswitch position )

3 High beam flasher (high beamavailable independent ofexterior lamp switch position)

4 Turn signals, right5 Turn signals, left

To signal minor directional changes,such as changing lanes on a highway,move combination switch to the pointof resistance only and hold it there.

To operate the turn signalscontinuously, move the combinationswitch past the point of resistance (up ordown). The switch is automaticallycanceled when the steering wheel isturned to a large enough degree.

6 Press switch briefly:One wipe without washer water(select only if window is wet)Pressswitch past resistance point:Windshield washer, windshieldwiper; headlamp cleaning system(only in exterior lamp switchpositions or Canada only:also in position when the engine isrunning)

7 Windshield wiper0 Wiper offI Intermittent wipingII Normal wiper speedIII Fast wiper speedWhen coming to a stop or drivingslower than approx. 20 km/h (13mph), the wiper speed automaticallyswitches to the next lower setting.In setting "I", the interval betweenwipes is lengthened.Upon accelerating again, the wiperspeed returns to the previous setting.

Note:

The windshield washer reservoir,hoses and nozzles are automaticallyheated.

56

Windshield Washer Fluid MixingRatio

For temperatures above freezing:

MB Windshield WasherConcentrate "S" and water

1 part "S" to 100 parts water(40 ml "S" to 1 gallon water).

For temperature below freezing:

MB Windshield Washer Concentrate"S" and commercially availablepremixed windshield washersolvent/antifreeze

1 part "S" to 100 parts solvent(40 ml "S" to 1 gallon solvent),

Windshield Wiper Smears

If the windshield wiper smears thewindshield, even during rain, activatethe washer system as often asnecessary. The fluid in the washerreservoir should be mixed in the correctratio.

Blocked Windshield Wiper

If the windshield wiper becomesblocked (for example, due to snow),switch off the wiper motor.

For safety reasons before removing iceor snow, remove key from steeringlock. Remove blockage.

Activate combination switch again(key in steering lock position 1).

Emergency Operation ofWindshield Wiper

In case of windshield wipermalfunction, turn combination switchto wiper setting II.

Have the system checked at yourauthorized MERCEDES-BENZ dealeras soon as possible.

Signaling Turns with HazardFlasher in Use

For example, when the vehicle isbeing towed:

With hazard flasher on, activatecombination switch for left or rightturn signal - only the selected turnsignal will blink.

Upon canceling the turn signal, all fourturn signals will operate again.

Turn Signal Failure

If one of the turn signals fails, the turnsignal indicator system flashes andsounds at a faster than normal rate. Inaddition, the exterior lamp failureindicator will come on.

57

Exterior Lamp Switch

Canada only:

When the engine is running, the lowbeam (includes parking lamps, sidemarker lamps, taillamps, license platelamps and instrument panel lamps) areautomatically switched on.

Note:

For nighttime driving the exterior lampswitch should be turned to position IDto permit activation of the highbeam headlamps.

Off

Parking lamps (also sidemarker lamps, taillamps,license plate lamps,instrument panel lamps)Canada only: When theengine is running, the lowbeam is additionallyswitched on.Parking lamps plus lowbeam or high beamheadlamps (combinationswitch pushed forward)Standing lamps, right(turn left one stop)Standing lamps, left(turn left two stops)

Fog lamps(pull out one stop) withparking and/orheadlamps onRear fog lamp (pull out to2nd detent) in addition tofog lamps. Indicator lamp inlamp switch comes on.

Standing Lamps

When the vehicle is parked on thestreet the standing lamps (right or leftside parking lamps) can be turned on,making the vehicle more visible topassing vehicles.

The standing lamps cannot beoperated with the key in steering lockposition 2.

Note:With the key removed and a front dooropen, an audible warning will sound ifthe vehicle's exterior lamps (exceptstanding lamps) are not switched off.Fog lamps will operate with theparking lamps and the low or highbeam headlamps. Fog lamps shouldonly be used in conjunction with lowbeam headlamps. Consult your stateMotor Vehicle Regulations regardingallowable lamp operation.

Fog lamps are automatically switchedoff when the exterior lamp, switch isturned to position O .

58

Inside and Exterior Rear ViewMirrors

Inside Rear View Mirror

The mirror is electricallyadjustable.

Use your inside mirror to determine thesize and distance of objects seen in thepassenger side convex mirror.

The switch is located on the centerconsole.

Turn switch to position steering lock toposition 2 (with either front door open,the mirror can be operated with keyremoved or in steering lock position 0or 1).

Turn switch to position

To adjust, move the switch forward,backward or to either side.

Antiglare Night Position

Manual adjustment

Tilt the mirror to the antiglare nightposition using the lever at its lower edge.

Automatic adjustment

With the key in steering lock position2, the mirror responds to changes inlight sensitivity.

59

Exterior rear view mirror, leftExterior rear view mirror,right

Exterior Rear View Mirrors

Turn key in steering lock to position 2(with either front door open, themirrors can be operated with keyremoved or in steering lockposition 0 or 1).

Turn switch to select the mirror to beadjusted.

To adjust, move the switch forward,backward or to either side.

Note:

The exterior mirrors have electricallyheated glass. The heater switches onautomatically, depending on outsidetemperature.

If an exterior mirror housing is forciblypivoted from its normal position, itmust be repositioned by applying firmpressure until it snaps into place.

Warning!

Exercise care when using thepassenger-side mirror. Thepassenger-side exterior mirror isconvex (outwardly curved surfacefor a wider field of view). Objects inmirror are closer than they appear.Check your inside rear view mirroror glance over your shoulder beforechanging lanes.

60

Exterior Rear View MirrorMultiple Images

This vehicle is equipped with anti-fogging dual-pane side windows toprovide extra insulation against heat,cold and noise. Because of the secondpane of glass, under certain light andweather conditions a multiple imagemay become noticable, especially whenlooking through the side windows at anoutside rear view mirror.

Storing Mirror Positions inMemory

The exterior and inside rear viewmirror positions are stored in memorywith the seat/head restraint/ steeringcolumn position and can be recalledwhen necessary, see Index.

Note:

If the inside rear view mirror wasadjusted separately, the originallystored position remains in memory.To recall position, press the desiredposition button.

Folding the mirrors in

Turn switch to point rearward. Pressswitch rearward until the mirrors arefolded in.

Important!

Before running the vehicle through anautomatic car wash, fold mirror in,otherwise they may get damaged.

Folding the mirrors out

Turn switch to point rearward. Pressswitch forward until the mirrors arefolded out.

Important!

Do not fold mirrors out, forcing themby hand. This will damage theoperating mechanism of the mirrors.

61

Sun Visors

Swing sun visors down to protectagainst sun glare.

If sunlight enters through a sidewindow, disengage visor from innermounting and pivot to theside. From this position, the visor canslide forward and backward on itsshaft.

Illuminated Vanity Mirrors

Front seats:

With the visor engaged in its innermounting, the lamp can be switchedon by opening the cover.

Roar seats:

Touch the cover to lower the mirror.The lamp will switch on automatically.

Close the cover and the lamp will goout.

62

Interior Lighting

1 Interior Lamps (Door contact)

A B

A Interior lamps are switched on,and off delayed, when unlockingor locking the vehicle, or whenopening or closing either frontdoor. However, there will be nodelay when the key is in steeringlock position 2.

B Interior lamps switched off.

2 Interior Lamps

A B

A Interior lamps switched off.B Interior lamps switched on,

3 Rear Courtesy Lamps

A B

A Courtesy lamps switched off.B Courtesy lamps switched on.

Note:

The courtesy lamps cannot beswitched off as long as a rear door isopen.

4 Reading Lamps, Front

A

B

A Reading lamp switched off.B Reading lamp switched on.

5 Reading Lamps, Rear

The lamps are switched on and offindividually with a switch in therespective lamp.

Entrance Lamps, Exit Lamps

The lamps are switched on and off bythe door contact switches.

Note:

To prevent the vehicle battery frombeing discharged, do not leave doorsopen for a long period of time.

63

Storage Compartments

Storage Compartmentsin the Dashboard

1 Storage/eyeglassescompartment

2 Button for storage/eyeglasses compartment

3 Glove box

4 Button for glove box

5 Lock

Storage/EyeglassesCompartment

To open: Press button (2).

Glove Box

The glove box lid is equipped with acontainer for coins and smallaccessories.

To open: Press button (4).

Note:The storage compartments may belocked and unlocked by using themaster key in lock (5).

Locking:Turn master key in lock (5) to the rightand remove.

Unlocking:Turn master key back to verticalposition.

Storage Compartment betweenRear Seats

Lock only when compartment is fullyclosed, otherwise the lock may getdamaged.

Storage Compartmentsin the Door

6 Door pocketTo open: Fold down cover.

7 Compartment for compact umbrella.

Caution!

Keep compartment lids closed. Thiswill prevent stored objects from beingthrown about and injuring vehicleoccupants during an accident.

64

in center console, front

Ashtrays

By touching the top of the coverlightly, the ashtray opens automatically.Prior to removing the ashtray insertmove gear selector lever to position"N"

Warning!

With the gear selector lever inposition "N", turn off the engine andset the parking brake. Otherwise thevehicle might move unintentionally.

in rear doors

To remove ashtray from centerconsole:

Push sliding knob (1) toward theright to eject the insert.

To remove ashtray from rear door:Hold left and right side of insert andpull up.

To install ashtray:Install insert into ashtray frameand push down to engage.

Lighter

Turn key in steering lock toposition 1 or 2.Push in lighter (1); it will pop outautomatically when hot.

Warning!

Never touch the heating element orsides of the lighter, hold at knob only.

65

Sliding Roof with Rear Pop-UpFeature

1 to slide roof open2 to slide roof closed3 to raise roof at rear4 to lower roof at rear

Turn key in steering lock to position1 or 2 (with either front door open,the sliding/pop-up roof can beoperated with key removed or insteering lock position 0).

The switch is illuminated when theexterior lamps are switched on(except standing lamps).

Glass Sliding Roof with RearPop-Up Feature

An additional screen can be slid intothe roof opening to guard against sunrays. When sliding the roof open, thescreen will also retract.

Warning!

When closing the sliding roof, besure that there is no danger ofanyone being harmed by the closingprocedure.

Notes:

The sliding roof can be opened orclosed manually should an electricalmalfunction occur, refer to EmergencyOperation in Index.

The sliding roof can also be closedwith the key or infrared remote controlwhile locking the vehicle doors ortrunk (see Central Locking System inIndex).

66

in center console, front

Power Windows

Switches for:

2 left, front3 left, rear4 right, front5 right, rear6 safety switch7 individual switches (rear doors)

in rear doors

Turn key in steering lock toposition 1 or 2.

Press switch in to resistance point:

to closeto open

Release switch when window is indesired position.

Express Opening and Closing

Press switch or pastresistance point and release - windowopens or closes completely.

To interrupt procedure, brieflypress orIf the upward movement of thewindow is blocked during the closingprocedure, the window will stop duringthe last few inches before closure andopen slightly.

When pressing and holding the switchto close the window, and upwardmovement of the window is blockedduring the last few inches beforeclosure, it will stop but not openslightly.

Blocking of Rear Door WindowOperation

If no operation of the rear windows byswitch (6) (for instance by children) isdesired, slide safety switch (5) to right,symbol becomes visible.

67

Warning!

When closing the windows, be surethat there is no danger of anyonebeing harmed by the closingprocedure.

In case of obstruction, the automaticreversal will not operate if a windowis being closed by pressing the switchto its resistance point and holding itthere, or when using a key or theremote control.

The closing procedure can beimmediately reversed by eitherpressing the switch , turning thekey to the unlocking position, orreleasing and pressing the transmitbutton, and holding it.

The power windows can also be closedwith the key or infrared remote controlwhile locking the vehicle doors ortrunk (see Central Locking System inIndex).

Warning!

When leaving the vehicle, alwaysremove the key from the steeringlock. Do not leave childrenunattended in the vehicle.Unsupervised use of vehicleequipment can cause seriouspersonal injury.

Note:

If the side windows cannot be fullyopened or closed automatically bypressing the button past the point ofresistance (e.g. after a vehicle batterychange), press side of powerwindow switch until the window iscompletely closed and hold foradditional 2 seconds. Repeat procedurefor each window.

The automatic full opening and closingprocedure of the windows should nowbe restored.

1 Raising2 Lowering

Rear Window Sunshade

The switches are located on the centerconsole and between the single rearseats.

The sunshade should always be eitherfully raised or fully lowered.

68

Rear Window Defroster

The switch is located in the centerconsole.

Turn key in steering lock toposition I or 2.

When activating the rear windowdefroster, the indicator lamp in theswitch will come on.

Note:

The rear window defroster uses a largeamount of power. To keep the batterydrain to a minimum, turn off thedefroster as soon as the window isclear.

The defroster is automatically turned offafter a maximum of 20 minutes ofoperation.

Heavy accumulation of snow and iceshould be removed before activatingthe defroster.

If several power consumers are turnedon simultaneously, or the battery isonly partially charged, it is possiblethat the defroster will automaticallyturn itself off. When this happens, theindicator lamp inside the switch startsblinking.

As soon as the battery has sufficientvoltage, the defroster automaticallyturns itself back on.

Shelf below Rear Window

Warning!

The shelf below the rear windowshould not be used to carry objects.This will prevent such objects frombeing thrown about and injuringvehicle occupants during an accidentor sudden maneuver.

69

Setting Clock

Adjusting clock one minute ahead orback:

Pull out adjustment knob (1), brieflyturn to the right respectively left andrelease knob.

Adjusting clock more than one minuteahead or back:

Pull out adjustment knob (1), turn tothe right respectively left and hold untilthe desired time is set. Within the first2 seconds, the minute hand advances8 minutes and advances another 8minutes every additional secondthereafter.

Antenna

The antenna extends when switchingon the radio and/or telephone.

Note:

To retract the antenna (e.g. whenentering a car wash) both radio andtelephone must be switched off.

Cellular Telephone

The vehicle is prepared for theinstallation of a cellular telephone. Forfurther information and installationcontact your authorized Mercedes-Benz dealer.

Warning!

Some jurisdictions prohibit the driverfrom using a cellular telephone whiledriving a vehicle. Therefore, forsafety reasons, the driver should notuse the cellular telephone while thevehicle is in motion. Stop the vehiclein a safe location before answering orplacing a call.

70

71

Driving

72

Drinking and Driving

Warning!

Drinking and driving can be a verydangerous combination. Even a smallamount of alcohol or drugs can affectyour reflexes, perceptions andjudgement.

The possibility of a serious or evenfatal accident is sharply increasedwhen you drink and drive.

Please don't drink and drive or allowanyone to drive after drinking. Parking Brake

To engage, depress parking brakepedal. When the key is in steering lockposition 2, the brake warning lamp inthe instrument cluster should come onbrightly.

To release the parking brake, pullhandle on instrument panel. The brakewarning lamp in the instrument clustershould go out.

Also see Brake Warning Lamp Test inIndex.

Driving Off

Test the brakes briefly after driving off.Perform this procedure only when theroad is clear of other traffic.

Warm up the engine smoothly. Do notplace full load on the engine until theoperating temperature has been reached.

When starting off on a slippery surface,do not allow one driving wheel to spinfor an extended period.

Warning!

Keep driver's foot area clear at alltimes. Objects stored in this area mayimpair pedal movement.

73

Automatic Transmission

The automatic transmission selectsindividual gears automatically,dependent upon

• Selector lever position• Accelerator position• Vehicle speed

Important!

When parking the car or beforeworking on the vehicle with the enginerunning, firmly depress the parkingbrake pedal and shift the selector leverinto "P".

Driving

The selector lever is automaticallylocked while in position "P". Tomove the selector lever out ofposition "P", the service brake pedalmust be firmly depressed before theshift lock will release.

Shift selector lever to the desireddriving position only when theengine is idling and the servicebrake is applied. Do not release thebrake until ready to drive. Thevehicle may otherwise start creepingwhen the selector lever is in drive orreverse position.

Warning!

It is dangerous to shift the selectorlever out of "P" or "N" if the enginespeed is higher than idle speed. Ifyour foot is not on the brake pedal,the car could accelerate quicklyforward or in reverse. You could losecontrol of the car and hit someone orsomething. Only shift into gear whenthe engine is idling normally andwhen your right foot is firmly on thebrake pedal.

Accelerator position

Partial throttle = early upshifting =normal acceleration

Full throttle = later upshifting =rapid acceleration

Kickdown (depressing the acceleratorbeyond full throttle) = downshiftingto next lowest gear = maximumacceleration. Once the desired speedis attained, ease up on the accelerator- the transmission shifts up again.

74

Selector Lever Positions

The automatic gear shifting processcan be adapted to specific operatingconditions using the selector lever.

P Parking lock.The parking lock is an additionalsafeguard to the parking brake whenparking the vehicle. Engage onlywith the car stopped.

Note:

The key can be removed from thesteering lock only with the selectorlever in position "P". With the keyremoved, the selector lever islocked in position "P".

R Reverse gear.Shift to reverse gear only with thecar stopped.

N Neutral.No power is transmitted from theengine to the rear axle. When thebrakes conditions are released, thevehicle can be moved freely (pushedor towed). Do not engage "N" whiledriving except to coast when thevehicle is in danger of skidding(e.g. on icy roads, see WinterDriving Instructions in Index).

Important!

Coasting the vehicle, or driving forany other reason with selector leverin "N", can result in transmissiondamage that is not covered by theMercedes-Benz Limited Warranty.

D The transmission automaticallyupshifts to 5th gear. Position "D"provides optimum drivingcharacteristics under all normaloperating

3 Upshift to 4th gear only. Suitablefor performance driving.

2 Upshift to 3rd gear only. Suitablefor moderately steep hills. Since thetransmission does not shift higherthan 3rd gear, this gear selectionwill allow use of the engine's brak-ing power downhill.

75

Important!

Do not exceed the vehicle speed limitsfor individual gear selections, which areindicated by marks (I, II, III etc.) on thecircumference of the speedometer.

Do not brake the vehicle by down-shifting to a lower gear (for examplefrom "D" to "3") unless the speedometerneedle is below the speed limit mark ofthat particular gear range. Overrevvingcould result in serious damage to theengine.

Warning!

On slippery road surfaces, neverdownshift in order to obtain brakingaction. This could result in rear wheelslip and reduced vehicle control. Yourvehicle's ABS will not prevent thistype of loss of control.

To prevent the engine from laboring atlow RPMs, do not allow the enginespeed to drop too low on uphillgradients.

Depending on the degree of the incline,shift selector lever to a lower gear rangeearly enough to maintain engine RPMwithin the best torque range.

Maneuvering

To maneuver in tight areas, e.g. whenpulling into parking space, control thecar speed by gradually releasing thebrakes. Accelerate gently and neverabruptly step on the accelerator.

To rock a car out of soft ground (mudor snow), alternately shift from forwardto reverse, while applying slight partialthrottle.

Rocking a car free in this manner maycause the ABS warning lamp to comeon. Turn off and restart the engine toclear the malfunction indication.

Stopping

For brief stops, e.g. at traffic lights,leave the transmission in gear and holdvehicle with the service brake.

For longer stops with the engine idling,shift into "N" or "P".

When stopping the car on an uphillincline, do not hold it with theaccelerator, use the brake. This avoidsunnecessary transmission heat build up.

Warning!

Getting out of your car with theselector lever not fully engaged inposition "P" is dangerous. Whenparked on a steep incline, position"P" alone may not prevent yourvehicle from moving, possibly hittingpeople or objects.

Always set the parking brake inaddition to shifting to position "P".

When parked on an incline, also turnfront wheel against curb.

76

Rear Fender Indicators

When the reverse gear is selected, therear fender indicators will extendupward from the rear corners of thefenders.

The rear fender indicators retractdelayed when shifting out of reverse.They retract immediately when turningkey in steering lock to position 0.

Note:

Before shifting into reverse gear,ensure that the rear fender indicatorscan extend freely.

Cruise Control

Any given speed above approximately25 mph (40 km/h) can be maintainedwith the cruise control by operating thelever.

1 Accelerate and set:Lift lever briefly to set speed.Hold lever up to accelerate.

2 Decelerate and set:Depress lever briefly to set speed.Hold lever down to decelerate.

Normally the vehicle is accelerated tothe desired speed with the accelerator.

Speed is set by briefly pushing thelever to position 1 or 2. The acceleratorcan be released.

The speed can be increased (e.g. forpassing) by using the accelerator. Assoon as the accelerator is released, thepreviously set speed will be resumedautomatically.

If a set speed is to be increased ordecreased slightly, e.g. to adapt to thetraffic flow, hold lever in position 1 or2 until the desired speed is reached, orbriefly tip the control lever in theappropriate direction for increases ordecreases in 0.6 mph (1 km/h)increments. When the lever is released,the newly set speed remains.

77

3 Canceling

To cancel the cruise control, brieflypush lever to position 3.

When you step on the brake or thevehicle speed drops below approx.25 mph (40 km/h), for examplewhen driving upgrade, the cruisecontrol will be canceled.

If the cruise control cancels byitself and remains inoperative untilthe engine is restarted, have thesystem checked at your authorizedMercedes-Benz dealer as soon aspossible.

4 Resume

If the lever is briefly pushed toposition 4 when driving at a speedexceeding approx. 25 mph (40km/h), the vehicle resumes thespeed which was set prior to thecancellation of the cruise control.The last memorized speed iscanceled when the key in thesteering lock is turned to position 1or 0.

Note:

If the engine does not brake the vehiclesufficiently while driving on adowngrade, the speed you set on thecruise control may be exceeded andyou may have to step on the brakepedal to slow down. As soon as thegrade eases, the cruise controlled speedwill again be maintained as long as thebrakes were not previously applied, orthe lever may be used to resume thepreviously set speed if the brakes wereapplied.

Caution!

When driving with the cruise control,the transmission selector lever mustnot be shifted to position "N" asotherwise the engine will overrev.

Warning!

Only use the cruise control if thetraffic and weather conditions makeit advisable to travel at a steadyspeed.

• The use of cruise control can bedangerous on winding roads or inheavy traffic because conditionsdo not allow safe driving at asteady speed.

• The use of cruise control can bedangerous on slippery roads.Rapid changes in tire adhesioncan result in wheel spin and lossof control.

The "Resume" function should onlybe operated if the driver is fullyaware of the previously set speed andwishes to resume this particularpreset speed.

78

Charge Indicator Lamp

Should the charge indicator lamp fail tocome on prior to starting when the keyis in steering lock position 2 or shouldit fail to go out after starting or duringoperation, this indicates a fault whichmust be repaired at an authorizedMERCEDES-BENZ dealerimmediately.

If the charge indicator lamp comes onwhile the engine is running, this mayindicate that the poly-V-belt hasbroken. Should this condition occur,the poly-V-belt must be replaced beforecontinuing to operate the vehicle.Otherwise, the engine will overheat dueto an inoperative water pump whichmay result in damage to the engine.

Engine Oil Pressure Gauge with OilPressure-Warning Lamp

With the key in steering lock position2, the oil pressure warning lamp comeson and goes out with the enginerunning.

The oil pressure at idle speed may dropif the engine is at operatingtemperature. This will not jeopardizethe engine's operational reliability.

Pressure must, however, riseimmediately upon acceleration.

Note:

If the oil pressure warning lamp doesnot go out after starting the engine orcomes on while driving and the oilpressure gauge needle drops to "0",then damage to the

engine may occur with continuedoperation. Turn off engine immediatelyand contact an authorized Mercedes-Benz dealer. Do not operate the caruntil the condition is repaired.

There is no need for concern should theoil pressure warning lamp light upbriefly, (for example, in sharp turns orhard braking) provided the lamp goesout immediately. We recommend youto drive to the nearest service stationwhere the engine oil should be toppedto the "full" mark on the dipstick withan approved oil.

79

Low Engine Oil Level WarningLamp

With the key in steering lock position2, the oil pressure warning lamp comeson and goes out with the enginerunning.

If the warning lamp comes on with theengine running and at operatingtemperature, the engine oil level hasdropped to approximately theminimum mark on the dipstick.

When this occurs, the warning lampwill first come on intermittently andthen stay on if the oil level dropsfurther.

If no oil leaks are noted and there isindicated engine oil pressure, continueto drive to the nearest service stationwhere the engine oil should be toppedto the "full" mark on the dipstick withan approved oil.

In addition to the warning lamp, theengine oil level should beperiodically checked with thedipstick, for example during a fuelstop, or before a long trip. See Index.

Engine Oil Consumption

Engine oil consumption checks shouldonly be made after the break-in period.During the break-in period, higher oilconsumption may be noticed and isnormal. Frequent driving at highengine speeds results in increasedconsumption.

Fuel Consumption Gauge

While driving, instantaneous fuelconsumption is indicated in miles pergallon (mpg), or in Canada liters per100 kilometers (I/100 km).

With the engine switched off, theneedle reads "0".

Due to system design, maximumconsumption is indicated at idle speed.

80

Fuel Reserve Warning Lamp

With the key in steering lock position2, the fuel reserve warning lamps comeon and should go out when the engineis running.

If the warning lamps do not go outafter starting the engine or if they comeon while driving, it indicates that thefuel level is down to the reservequantity of approx. 3.3 gal (12.5 liters),

Outside Temperature Indicator

The temperature sensor is located inthe front bumper area. Due to itslocation, the sensor can be affected byroad or engine heat during idling orslow driving. This means that theaccuracy of the displayed temperaturecan only be verified by comparison to athermometer placed next to the sensor,not by comparison to external displays(e.g. bank signs, etc.).

Adaptation to ambient temperaturetakes place in steps and depends on theprevailing driving conditions (stop-and-go or moderate, constant driving)and amount of temperature change.

Warning!

The outside temperature indicatoris not designed to serve as an Ice-Warning Device and is thereforeunsuitable for that purpose.Indicated temperatures just abovethe freezing point do not guaranteethat the road surface is free of ice.

Coolant Temperature Gauge

If the antifreeze mixture is effective to- 30°C (- 22°F), the boiling point of thecoolant in the pressurized coolingsystem of your vehicle is approx.130°C (266 °F).

During severe operating conditions andstop-and-go city traffic, the coolanttemperature may rise close to the redmarking.

The engine should not be operated withthe coolant temperature in the redzone.

Warning!

• Driving when your engine is badlyoverheated can cause some fluidswhich may have leaked into theengine compartment to catch fire.You could be seriously burned.Turn off the engine and get out ofthe car until it cools down.

• Steam from an overheated enginecan cause serious burns and canoccur just by opening the enginehood. Stay away from the engine ifyou see or hear steam comingfrom it. Turn off the engine and donot stand near the car until itcools down.

81

Low Engine Coolant Level

Warning Lamp

With the key in steering lock position2, the warning lamp comes on andgoes out when the engine is running.

If the warning lamp does not go outafter starting the engine, or if it comeson while driving, then the coolantlevel has dropped below the requiredlevel. If no leaks are noticeable andthe engine temperature does notincrease, continue to drive to thenearest service Station and havecoolant added to the coolant system(see Index).

In cases of major or frequent minorcoolant loss, have the cooling systemchecked at your authorized Mercedes-Benz dealer as soon as possible.

Note:

Do not drive without coolant in thecooling system. The engine willoverheat causing major enginedamage.

Monitor the coolant temperature gaugewhile driving.

Warning!

Do not spill antifreeze on hot engineparts. Antifreeze contains ethyleneglycol which may burn if it comesinto contact with hot engine parts.You can be seriously burned.

Low Windshield and HeadlampWasher System Fluid Level

Warning Lamp

With the key in steering lock position2, the warning lamp comes on and goesout with the engine running.

If the warning lamp comes on with theengine running, the level of thereservoir has dropped to approx. 1/4 pfthe total volume. The reservoir shouldbe refilled with MB Windshield WasherConcentrate "S" and water (orcommercially available premixedwindshield washer solvent/antifreeze,depending on ambient temperature -see Index) at the next opportunity. Thereservoir for the windshield andheadlamp washer system is located inthe engine compartment next to theradiator.

The fluid level can be checkedvisually at the sight glass located nextto the reservoir filler cap.

82

Exterior Lamp Failure IndicatorLamp

With the key in steering lock position2, a dim indicator lamp comes on, andgoes out when the engine is running.

With the key in steering lock position 2or with the engine running, a brightillumination of this lamp indicates anexterior lamp failure.

If an exterior lamp fails, the in-dicator lamp will come on onlywhen that lamp is switched on.

If a brake or turn signal lamp fails, thelamp failure indicator will come onwhen applying the brake or actuatingthe turn signal and stay on until theengine is turned off.

Note:

The indicator lamp will also come on ifan incorrect bulb is installed.

If additional lighting equipment isinstalled (e.g. auxiliary headlamps etc.)be certain to connect into the fusebefore the failure indicator monitoringunit in order to avoid damaging thesystem.

Seat Belt Warning Lamp

With the key in steering lock position2, the warning lamp comes on and anaudible warning sounds for a shorttime if the driver's seat belt is notfastened.

After starting the engine, the warninglamp blinks for a brief period toremind the driver and passengers tofasten seat belts before driving off.

Brake Pad Wear Indicator Lamp

The brake pad wear indicator lamp inthe instrument cluster comes on whenthe key in the steering lock is turned toposition 2 and goes out when theengine is running.

If the indicator lamp lights up duringbraking, this indicates that the frontwheel brake pads are worn down (onvehicles equipped with ASR, itindicates that the front and/or rearwheel brake pads are worn down).

Have the brake system checked at yourauthorized Mercedes-Benz dealer assoon as possible.

83

Brake Warning Lamp

The brake warning lamp will come onwith the key in steering lock position2 and should go out when the engineis running.

The brake warning lamp will come on:

• when there is insufficient brakefluid in the reservoir (enginerunning and parking brakereleased)

• when the parking brake is set(engine running).

Warning!

Driving with the brake warninglamp on can result in an accident.Have your brake system checkedimmediately if the brake warninglamp stays on. Don't add brake fluidbefore checking the brake system.Overfilling the brake fluid reservoircan result in spilling brake fluid onhot engine parts and the brake fluidcatching fire. You can be seriouslyburned.

When the minimum mark on thereservoir is reached, have the brakesystem checked for brake pad thicknessand leaks.

To test the brake warning lamp, turnkey in steering lock to position 2. Thebrake warning lamp comes on, andshould go out when the engine isrunning.

84

Antilock Brake System (ABS)

The ABS prevents the wheels fromlocking up above a vehicle speed ofapproximately 3 km/h (2 mph)independent of road surface conditions.It is necessary, however, that thevehicle speed reaches at least 8 km/h (5mph) before commencing to brake.

At the instant one of the wheels isabout to lock up, a slight pulsation canbe felt in the brake pedal, indicatingthat the ABS is in the regulating mode.

On slippery road surfaces, the ABSwill respond even with only slightbrake pedal pressure. The pulsatingbrake pedal can be an indication ofhazardous road conditions andfunctions as a reminder to take extracare while driving.

The ABS warning lamp in theinstrument cluster comes on with thekey in steering lock position 2 andshould go out with the engine running.

If the charging voltage falls below 10volts, the warning lamp comes on andthe ABS is switched off. When thevoltage is above this value again, thewarning lamp should go out and theABS will be operational.

If the ABS warning lamp does not goout or comes on while driving, itindicates that the ABS has detected amalfunction and has switched off. Inthis case, the brake system functions inthe usual manner, but without antilockassistance.

Have the system checked at yourauthorized MERCEDES-BENZ dealeras soon as possible.

Warning!

Even the ABS cannot prevent thenatural laws of physics from actingon the vehicle. The ABS cannotprevent accidents, including thoseresulting from excessive speed inturns, following another vehicle tooclosely, or aquaplaning. Only a safe,attentive, and skillful driver canprevent accidents. The capabilities ofan ABS equipped car must never beexploited in a reckless or dangerousmanner which could jeopardize theuser's safety or the safety of others.

Note:

To alert following vehicles to slipperyroad conditions you discover, operateyour hazard warning flashers asappropriate.

85

Automatic Locking Differential(ASD)

The automatic locking differentialengages when there is a difference inspeed (slip) during acceleration betweenthe front and rear wheels of over 1.2mph (2 km/h) and the vehicle speed isless than 15.6 mph (25 km/h). It willdisengage at speeds above 16.2 mph(26 km/h).

The yellow function indicator in thespeedometer comes on whenever thereis a difference in speed between thefront and rear wheels of over 1.2 mph(2 km/h), warning of slippery roadconditions.

In steering lock position 2, the yellowfunction indicator lamp and the yellowASD warning lamp in the instrumentcluster should come on and then mustgo out with the engine running.

If the ASD warning lamp comes onwith the engine running, a malfunctionhas been detected. We recommend thatyou visit an authorized Mercedes-Benzdealer as soon as possible to have theASD checked.

Caution!

If the vehicle is towed with the frontaxle raised, the key must not be insteering lock position 2. Otherwise, theautomatic locking differential controlwill immediately be engaged, whichmay cause loss of towing control.

Notes:

The automatic locking differential willnot engage at speeds above 15.6 mph(25 km/h). However, above this speed,a limited-slip effect of up to 35%always present.

When testing the parking brake on abrake test dynamometer, turn off theengine to avoid engaging the automaticlocking differential.

In winter operation, the maximumefficiency of the automatic lockingdifferential can only be attainedthrough the use of Mercedes-Benzrecommended M + S radial-ply tires onall four wheels.

86

We recommend that you visit anauthorized Mercedes-Benz dealer assoon as possible to have the systemchecked-out.

Note:

If the battery was disconnected, theindicator lamp will only go out afterthe engine is started and the steeringwheel is turned from full left - to - fullright lock and returned to the centerposition.

Adaptive Damping System(ADS)

Depending upon road surfaceconditions, load, driving style, ADSwill automatically adjust the optimalride firmness.

The indicator lamp comes on with thekey in steering lock position 2 and goesout when the engine is running.

If the indicator lamp stays on after theengine is running or comes on whiledriving, then the system has detected amalfunction. Adaptive Damping System

Adjustment

The switch is located in the centerconsole.

1 Firm dampening program.This setting should be used forsporty driving.During the setting for sportydriving the indicator lamp in theswitch lights up.

2 Soft dampening program.This setting should be used forregular driving.

87

Emission Control

Certain systems of the engine serve tokeep certain components of the exhaustgases within permissible limitsrequired by law.

These systems, of course, will functionproperly only when maintained strictlyaccording to factory specifications.Any adjustments on the engine should,therefore, be carried out only byqualified Mercedes-Benz technicians.Engine adjustments should not bealtered in any way. Moreover, thespecified service and maintenance jobsmust be carried out regularly accordingto Mercedes-Benz servicingrequirements. For details refer to theMaintenance Booklet.

Warning!

Inhalation of exhaust gas ishazardous to your health. Allexhaust gas contains carbonmonoxide, and inhaling it can causeunconsciousness and lead to death.

Do not run the engine in confinedareas (such as a garage) which arenot properly ventilated. If you thinkthat exhaust gas fumes are enteringthe vehicle while driving, have thecause determined and correctedimmediately. If you must driveunder these conditions, drive onlywith at least one window fully open.

Traveling Abroad

Abroad, there is a widely-spreadMercedes-Benz service network atyour disposal. If you plan to travel intoareas which are not listed in the indexof your dealer directory, you shouldrequest pertinent information fromyour authorized Mercedes-Benz dealer.

88

Winter Driving

Have your car winterized at yourauthorized Mercedes-Benz dealerbefore the onset of winter.

• Change the engine oil if theengine contains an oil which isnot approved for winter operation.For viscosity (SAE class)and filling quantity, seeCapacities: Fuels, Coolants,Lubricants etc. in Index.

• For diesel fuels, refer to Index.• Check engine coolant

anticorrosion /antifreezeconcentration.

• Additive for the windshieldwasher and headlamp cleaningsystem: Add MB Concentrate"S" to a premixed windshieldwasher solvent/antifreezewhich is formulated for belowfreezing temperatures (seeIndex).

• Test battery: Battery capacitydrops with decreasing ambienttemperature. A well chargedbattery ensures that the enginecan always be started, even atlow ambient temperatures.

• Tires: We recommend M + Sradial-ply tires on all fourwheels for the winter season.Observe permissible maximumspeed for M + S radial-ply tiresand the legal speed limit.

• Engine block heater: The engine isequipped with a blockheater. The electrical cablemay be installed free-of-chargeat your authorized Mercedes-Benz dealer by using thecoupon in the "Owner's Serviceand Warranty Policy" booklet.The coupon is valid for 12months from date of vehicledelivery.

After installation, the electrical plugis located at the side of the radiator(behind the grill) and can beplugged into ordinary househouldoutlets. One or two hours ofoperation is usually sufficient topre-warm the engine beforestarting. The engine block heatercan be left plugged in overnight, ifdesired.

Note:

In winter operation, the maximumeffectiveness of the acceleration slipcontrol or of the automatic lockingdifferential is only achieved with M + Sradial tires.

Snow Chains

Use only snow chains that are testedand recommended by Mercedes-Benz.Your authorized Mercedes-Benz dealerwill be glad to advise you on thissubject.

Chains should only be used on the rearwheels. Follow the manufacturer'smounting instructions.

Snow chains should only be driven onsnow covered roads at speeds not toexceed 30 mph (50 km/h). Removechains as soon as possible whendriving on roads without snow.

For tips on driving on slippery winterroads, refer to Index.

89

Practical Hints

90

Hood

To open:To unlock the hood, pull release lever(1) under the driver's side of theinstrument panel. At the same timehandle (2) will extend out of theradiator grill (it may be necessary tolift the hood up slightly).

Caution!

To avoid damage to the windshieldwipers of hood, open the hood onlywith wipers in the parked position.

Pull handle (2) out of radiator grill tostop and open hood. Do not lift hoodat louvers of grill! Make certain thewindshield wiper arm is not foldedforward.

To close:

Lower hood and let it drop into lockfrom a height of approx. 30 cm (1 ft).Do not press down on hood with hands.

To avoid hood damage, if hood is notfully closed, re-open and repeat closingprocedure.

Warning!

To help prevent personal injury, stayclear of moving parts when the hoodis open and the engine is running. Besure the hood is properly closedbefore driving.

91

Checking Coolant Level

To check the coolant level, the vehiclemust be parked on level ground and theengine stopped.

Check coolant level only when coolant iscold.

The coolant should reach the top of thetab inside the filler neck.

Warning!

• Use extreme caution when openingthe hood if there are any signs ofsteam or coolant leaking from thecooling system.

• Do not remove pressure cap oncoolant reservoir if enginetemperature is above 90°C(194°F). Allow engine to cool downbefore removing cap. The coolantreservoir contains hot fluid and isunder pressure.

• Using a rag, turn cap to first notchto relieve excess pressure. Ifopened immediately, hot scaldingfluid and steam will be blown outunder pressure, possibly causingpersonal injury,

• Do not spill antifreeze on hotengine parts. Antifreeze containsethylene glycol which may burn ifit comes into contact with hotengine parts. You can be seriouslyburned.

Adding Coolant.

If coolant has to be added, a 50/50mixture of water and MBanticorrosion/antifreeze should be added.

The drain plugs for the cooling systemare located on the right and left sides ofthe engine block and at the bottom of theradiator.

Anticorrosion/antifreeze, seeCoolants in Index.

92

Checking Engine Oil Level

1 Oil dipstick2 Oil filler cap

To check the engine oil level, parkvehicle on level ground, with engine atnormal operational temperature.

Check engine oil level approximately 5minutes after stopping the engine,allowing for the oil to return to the oilpan.

Wipe oil dipstick clean prior to checkingthe engine oil level.

Oil level must be betweenthe lower (min) andupper(max) mark of thedipstick

Do not overfill engine. Excessive oilmust be drained or siphoned.

For low engine oil level warning lamp,see Index.

93

Checking AutomaticTransmission Fluid Level

Dipstick locking lever

1 Release2 Engage

When noticing fluid loss or gearshifting malfunctions, we recommendto have your authorized Mercedes-Benz dealer check the transmissionfluid level.

The transmission fluid level shouldonly be checked with the engine idling,parking brake engaged and selectorlever in position "P". The vehicle mustbe parked on level ground.

Prior to the check, allow engine to idlefor approx. 1 to 2 minutes.

Measure fluid level with the dipstickcompletely inserted and the lockinglever released (1).

Extreme cleanliness must be observed!To wipe the dipstick, use a clean, lint-free cloth.

To fill the transmission with fluid, pourit through a fine-mesh filter into thedipstick opening. Even the slightestimpurity may cause operationaltroubles.

The fluid level in the transmission isdependent upon its temperature. Themaximum and minimum fluid levelmarks on the dipstick are applicablereferences only if the transmission fluidlevel has reached its normal operatingtemperature of 176° F (80°C).

Important!

If the transmission fluid cools down to68 - 86° F (20 - 30 °C), which is thenormal shop temperature range, thenthe maximum fluid level will beapproximately 0.4 in (10 mm) belowthe minimum mark on the dipstick. Westress this point because a fluid changeis normally performed when thetransmission fluid has cooled down toshop temperature.

The fluid level must not exceed thedipstick maximum mark with the fluidat operating temperature. Drain orsiphon excess fluid, if required.

Then push dipstick all the way in andswing locking lever downwards (2).

94

Turning Off Engine Manually

If the engine continues to run after thekey is turned to steering lock position0, open the hood and push down thelever marked "STOP" until the enginestops running.

Using an extension such as a pen orscrewdriver should make it easier topush the "STOP" lever down.

Warning!

To help prevent personal injury, stayclear of moving parts when the hoodis open and the engine is running. Besure the hood is properly closedbefore driving.

Bleeding of Fuel System

The fuel system is a self bleedingsystem. Turn the key in steering lockfully to the right and crank engine (forup to one minute maximum). Pushaccelerator pedal to the floor whilecranking engine. Only release key afterengine fires evenly.

95

Trunk Lamp

1 Switching off2 Switching on

Switch off (1) trunk lamp if the trunk isto remain open for along period of time.This prevents the vehicle battery frombeing discharged.The lamp switches on automatically,when you open the trunk again the nexttime.When you switch off the trunk lamp,the trunk lid handle will also retract. Toclose the trunk lid by its handle, firstswitch on (2) the trunk lamp.

Spare Wheel, Lug Wrench

1 Trunk floor2 Strap3 Luggage bowl4 Lug wrench

Roll back the floor mat. Lift the trunkfloor (1) and engage strap (2) in theeyelet on the edge of the trunk lid.

To remove the spare tire, turn luggagebowl (3) to the left and remove.

First Aid Kit1 Opening lidThe first aid kit is stored in the shelfbelow the rear window.

Stowing Things in the Vehicle

Warning!To help avoid personal injury duringa collision or sudden maneuver,exercise care when stowing things.Put luggage or cargo in the trunk ifpossible. Do not pile luggage or cargohigher than the seat backs. Do notplace anything on the shelf below therear window.

96

Vehicle Jack

See illustration for proper storage ofjack.

Before storing the jack on the felt inthe spare wheel well, the jack arm(1) must be lowered almost to thebase (2) of the jack.

Warning!

The jack is designed exclusively forjacking up the vehicle at the jacktubes built into either side of thevehicle. Use the jack only to lift thevehicle during a wheel change.Never get beneath the vehicle whileit is supported by the jack. Keephands and feet away from the areaunder the lifted vehicle. Alwaysfirmly set parking brake and blockwheels before raising vehicle withjack.

Do not disengage parking brakewhile the vehicle is raised. Be certainthat the jack is always vertical whenin use, especially on hills. Always tryto use the jack on level surface. Besure that the jack arm is fullyinserted in the jack tube. Alwayslower the vehicle onto sufficientcapacity jackstands before workingunder the vehicle.

Vehicle Tools, StorageCompartment below Tool Box

1 Lock tool box lid2 Unlock tool box lid

To open the storage compartment:Lift out tool box.

To insert the tool box: Positionrear end of tool box, press downits front end.

97

Wheels

Replace rims or tires with the samedesignation, manufacturer and type asshown on the original part. See yourauthorized Mercedes-Benz dealer forfurther information.

Warning!

Do not mix different tire con-struction types (i.e. radial, bias, andbias-belted) on your car becausehandling may be adversely affectedand may result in loss of control.

See your authorized Mercedes-Benzdealer for information on tested andrecommended rims and tires forsummer and winter operation. Theycan also offer advice concerning tireservice and purchase.

Tire Replacement

Front tires should be replaced in sets.Furthermore - in the event of tirereplacement - the spare wheel, ifpossible, should be used on the rearaxle. Rims and tires must be of thesame size and type. For dimensions,see "Technical Data".

We recommend that you break in newtires for approx. 60 miles (100 km) atmoderate speed. It is imperative thatthe wheel mounting bolts beretightened after approx. 60-300 miles(100-500 km).

On new vehicles retightening iscarried out during the 1st inspection.Retightening is also necessarywhenever wheels are fitted, e.g. whenthe spare wheel is used for the firsttime or when a set of wheels with M +S tires is installed.

Tightening torque: 110ft.lb. (150 Nm).

For rim and tire specifications, refer to"Technical Data".

Warning!

Worn, old tires can cause accidents.If the fire tread is badly worn, or ifthe tires have sustained damage,replace them.When replacing rims, use onlygenuine Mercedes-Benz wheel bolts(identified by Mercedes star)specified for the particular rim type.Failure to do so can result in thebolts loosening and possibly anaccident.

Rotating Wheels

The wheels can be rotated accordingto the degree of tire wear whileretaining the same direction of travel.Rotating, however, should be carriedout at a mileage of 3000 -6000 miles(5000 - 10 000 km), before thecharacteristic tire wear pattern(shoulder wear on front wheels andtread center wear on rear wheels)becomes visible, as otherwise thedriving properties deteriorate.

Important!

Unidirectional snow tires must alwaysbe mounted with arrow on tire sidewallpointing in direction of vehicle forwardmovement.

Note:Thoroughly clean the inner side of thewheels any time you rotate the wheelsor wash the vehicle underside.

The use of retread tires is notrecommended. Retread tires mayadversely affect the handlingcharacteristics and safety of thevehicle.

Dented or bent rims can cause tirepressure loss and damage to the

98

tire beads. For this reason, check rimsfor damage at regular intervals. Therim flanges must be checked for wearbefore a tire is mounted. Remove burrs,if any.

Warning!

The jack is designed exclusively forjacking up the vehicle at the jacktubes built into either side of thevehicle. Use the jack only to lift thevehicle during a wheel change. Neverget beneath the vehicle while it issupported by the jack. Keep handsand feet away from the area underthe lifted vehicle. Always firmly setparking brake and block wheelsbefore raising vehicle with jack.

Do not disengage parking brakewhile the vehicle is raised. Be certainthat the jack is always vertical whenin use, especially on hills. Always tryto use the jack on level surface. Besure that the jack arm is fullyinserted in the jack tube. Alwayslower the vehicle onto sufficientcapacity jackstands before workingunder the vehicle.

Changing Wheels

Move vehicle to a level area which is asafe distance from the roadway.

1. Set parking brake and turn onhazard warning flasher.

2. Move selector lever to position"P" and turn off engine.

3. Prevent vehicle from rolling away byblocking wheels with wheel chocksor sizable wood block or stone (notsupplied with, vehicle). Whenchanging a wheel on a hill, placechocks on the downhill side blockingboth wheels of the other axle. On alevel road, place one chock in front ofand one behind the wheel that is dia-gonally opposite to the wheel beingchanged.

4. Unfold wrench, loosen but do notremove the wheel bolts.

99

5. Remove the protective cover fromthe jack support tube opening byinserting a screwdriver in theopening and prying it out.

The tube openings are locateddirectly behind the front wheelhousings and in front of the rearwheel housings.

6. Insert jack arm fully into the tubehole up to the stop. Place jack onfirm ground. Position the jack so thatit is always vertical (plumb-line) asseen from the side (see arrow), evenif the vehicle is parked on an incline.

7. Jack up the vehicle until the wheel isclear of the ground. Never startengine while vehicle is raised.

7. Unscrew wheel bolts completely.Keep bolt threads protected fromdirt and sand.

9. Remove wheel.

10. Screw the alignment bolt (1)supplied in the tool kit into theupper-most threaded hole.

100

11. Install spare wheel on wheelhub. Insert wheel bolts andtighten them slightly.

To avoid paint damage, placewheel flat against hub and hold itthere while installing first wheelbolt.

Unscrew the alignment bolt toinstall the last wheel bolt.

12. Lower car. Remove jack andinsert jack tube cover.

13. Fold wrench together andtighten the five bolts evenly,following the sequenceillustrated above, until all boltsare tight.Observe a tightening torque of 110Nm (80 ft.lb.).

14. Correct tire pressure.

Important!

When installing new wheels themounting bolts must be retightenedafter approx. 100 to 500 km (60 - 300miles).

Before storing the jack, the jack armmust be lowered almost to the base ofthe jack. Store the spare wheel first andthen the vehicle jack.

Warning!

Incorrect mounting bolts orimproperly tightened mounting boltscan cause the wheel to come off. Thiscould cause an accident Be sure touse the correct mounting bolts.

101

Tire Inflation Pressure

A table (see fuel filler flap) lists the tireinflation pressures specified forsummer and winter tires as well as forthe varying operating conditions.

Important!

Tire pressure differs by approx. 0.1 bar(1.5 psi) per 10°C (18°F) of airtemperature change. Keep this in mindwhen checking tire pressure inside agarage especially in the winter.

Example:

If garage temperature = approx. + 20°C( + 68°F) and ambient temperature =approx. 0°C ( + 32°F) then the adjustedair pressure = specified air pressure +0.2 bar (+ 3 psi).

Tire pressures listed for light loads areminimum values offering high drivingcomfort.

Increased inflation pressures for heavyloads produce favorable handlingcharacteristics with lighter loads andare perfectly permissible. The ride ofthe vehicle, however, will becomesomewhat harder.

Tire temperature and pressure increasewith the vehicle speed. Tire pressureshould therefore only be corrected oncold tires. Correct tire pressure inwarm tires only if pressure has droppedbelow the pressure listed in the tableand the respective operating conditionsare taken into consideration.

An underinflated tire due to a slow leak(e.g. due to a nail in the tire) may causedamage such as tread separation,bulging, etc.. Regular tire pressurechecks (including the spare tire) atintervals of no more than 14 days aretherefore essential.

If a tire constantly loses air, it shouldbe inspected for damage.

Warning!

Do not overinflate tires,Overinflating tires can result insudden deflation (blow-out) becausethey are more likely to becomepunctured or damaged by roaddebris, potholes, etc. Follow recom-mended inflation pressures.

Do not overload the tires byexceeding the specified vehiclecapacity weight (as indicated by thelabel on the driver's door latch post).Overloading the tires can overheatthem, possibly causing a blow-out.

102

Battery

The maintenance-free battery is locatedin the trunk behind the right-hand coverpanel.

The service life of the battery is alsodependent on its condition of charge.The battery should always be keptsufficiently charged,in order to last anoptimum length of time.

Therefore, we strongly recommendthat you have the battery chargechecked frequently, and corrected ifnecessary, especially if you use thevehicle less than approximately 200miles (300 km) per month, mostly forshort distance trips, or if it is notused for long periods of time.

Only charge a battery with a batterycharger after it has been disconnectedfrom the vehicle electrical circuit.

When removing and connecting thebattery, always make sure that allelectrical consumers are off and thekey is in steering lock position 0.

While the engine is running the batteryterminal clamps must not be loosenedor detached, otherwise the alternatorand other electronic components wouldbe damaged.

Battery Recycling

Batteries contain materials that canharm the environment withimproper disposal.

Large 12 Volt storage batteries containlead, and smaller watch-type batteries(such as in the Infrared RemoteControl Unit) may contain mercury.

Recycling of batteries is thepreferred method of disposal.

Many states require sellers of batteriesto accept old batteries for recycling.

Warning!

Never lean over batteries whileconnecting or jump starting, youmight get injured.

Battery fluid contains sulfuric acid.Do not allow this fluid to come incontact with eyes, skin or clothing.In case it does, immediately flushaffected area with water and seekmedical help.

A battery will also producehydrogen gas, which is flammableand explosive. Keep flames or sparksaway from battery, avoid improperconnection of jumper cables,smoking, etc..

103

Exterior Lamps

When replacing bulbs, install only 12volt bulbs with the specified wattrating

Headlamp Assembly

1 Headlamp horizontal adjustmentscrew

2 Headlamp vertical adjustment screw

3 Fog lamp vertical adjustmentscrew

4 Scale for horizontal adjustment

5 Clamps for high and low beamheadlamp cover

6. Latch for turn signal, parking,side marker and standing lamphousing

7 Bulb socket for turn signal,parking, side marker and standinglamp bulb

8 Electrical connector for high andlow beam headlamp bulb

9 Electrical connector for fog lamp

10 Level for headlamp verticaladjustment

104

Replacing bulb:

When replacing halogen bulbs do nottouch glass portion of bulb with barehands. Use plain paper or a clean cloth.

Warning!

Halogen lamps contain pressurizedgas. A bulb can explode if you:

• touch or move it when hot,• drop the bulb,• scratch the bulb.

Bulb for high and low beamHB2 (60/55 W)

Bulb for fog lampYC (H3) (55 W)

Remove cover above headlamp. Moveretaining clamps (5) aside and removecover. Pull off electrical connector (8)respectively (9). Unhook clamping ringand pull out bulb together withclamping ring. Remove bulb.

Insert new bulb (seating properly incutouts of bulb socket), mountclamping ring. Reinstall and pushelectrical connector on securely.

Reinstall cover and fasten withretaining clamps (5).

Reinstall cover above headlamp, andcheck lamp for proper operation.

Turn Signal, Parking, SideMarker and Standing Lamp(1157 [21/5 W/32/3 cp] bulb)

Replacing bulb:

Squeeze latch (6) together and liftcomplete lamp assembly out to front ofvehicle. Twist bulb socket (7)counterclockwise and pull out. Pushbulb into socket, turn counterclockwiseand remove.

Insert new bulb in socket push in andtwist clockwise. Reinstall bulb socket.Reinstall lamp assembly until properlyseated and fasten latch (6).

105

Adjusting Headlamp

Correct headlamp adjustment isextremely important. To check andreadjust a headlamp do the following:

• Park unloaded vehicle on levelsurface. Check surface withcarpenter's level.

• Remove cover above headlamp.Move retaining clamps (5) aside andremove cover.

Note:

Horizontal headlamp aim normallynever changes and needs readjustmentonly after repair to the body or aheadlamp unit. Therefore, do not turnthe horizontal adjustment screw (1), ifnumber 0 on scale (11) aligns withmarker (12).

Vertical headlamp aim:

Turn adjusting screw (2) until thebubble in level (10) is in center of themarking (bold line).

Horizontal headlamp aim:

Turn adjustment screw (1) until thenumber 0 on scale (11) aligns withmarker (12).

• Reinstall cover and fasten withretaining clamps (5).

• Reinstall cover aboveheadlamp.

106

Taillamp Assemblies

1 Turn signal lamp(21 W/32 cp bulb)

2 Stop, side marker lamp(21/4 W/35/1.2 cp bulb)

3 Tail, parking lamp (5 W bulb)

4 Tail, parking and standing lamp(21/4 W/35/1.2 cp bulb)Driver's side: Tail, parking,standing and rear fog lamp(21/4 W/35/1.2 cp bulb)

5 Backup lamp(21 W/32 cp bulb)

6 Trunk lamp (10 W bulb)

To replace bulbs:

Turn locking lever on lamp cover tovertical position and swing open lampsupport. Push down on bulb to bechanged, twist counterclockwise andremove.

License Plate Lamps(5 W bulb)

Loosen both securing screws (1),remove lamp and take out bulb.

107

High Mounted Stop Lamp(H2 [20 W] bulb)

To replace the bulb, press tabs on bothsides (arrows) to release cover.

Turn bulb socket with bulbcounterclockwise and pull out.

Press bulb down, turn counterclockwiseand remove.

Main fuse box in engine compartment

Fuses

Before replacing a blown fuse,determine the cause of the short circuit.Spare fuses are supplied inside themain fuse box. Observe amperage andcolor of fuse.

Auxiliary fuse box in trunk behindright side cover

Always use a new fuse for replacement.Never attempt to repair or bridge ablown fuse.

After replacing a blown fuse, closefuse box cover.

108

Jump Starting

If the battery is discharged, the engineshould be started with jumper cablesand the (12 V) battery of anothervehicle.

The battery is located in the trunkbehind the right-hand cover panel.

Warning!

Failure to follow these directions willcause damage to the electroniccomponents, and can lead to abattery explosion and personalinjury.

Read all instructions beforeproceeding.

Proceed as follows:

1. Position the vehicle with thecharged battery so that thejumper cables will reach, butnever let the vehicles touch.Make sure the jumper cablesdo not have loose or missinginsulation.

2. On both vehicles:

• Turn off engine and all lights andaccessories, except hazardwarning flashers or work lights.

• Apply parking brake and shiftselector lever to position "P".

Important!

3, Clamp one end of the firstjumper cable to the positive(+) terminal of the dischargedbattery and the other end to thepositive (+) terminal of the chargedbattery. Make sure the cableclamps do not touch any othermetal parts.

4. Clamp one end of the secondjumper cable to the groundednegative (-) terminal of thecharged battery and the finalconnection to the negative (-)terminal of the dischargedbattery. Make sure the cablesare not on or near pulleys, fans,or other parts that will movewhen the engine is started.

109

Important!

5. Start engine of the vehicle withthe charged battery and run athigh idle. Then start engine ofthe disabled vehicle in theusual manner.

6. After the engine has started,remove jumper cables byexactly reversing the aboveinstallation sequence, startingwith the last connection madefirst. When removing eachclamp, make sure that it doesnot touch any other metal whilethe other end is still attached.

Warning!

Never lean over batteries whileconnecting or jump starting,you might get injured.

Battery fluid contains sulfuric acid.Do not allow this fluid to come incontact with eyes, skin or clothing. Incase it does, immediately flushaffected area with water, and seekmedical help.

A battery will also produce hydrogengas, which is flammable and veryexplosive. Keep flames or sparksaway from battery, avoid improperconnection of jumper cables,smoking etc..

Important!

A discharged battery can freeze atapprox. + 14°F (-10°C). In that case, itmust be thawed out before jumpercables are used.

Jumper cable specifications:

• Minimum cable cross-section of25 mm2 or approx. 2 AWG

• Maximum length of 11.5 ft.(3.5 m).

110

Towing the Vehicle

The rear towing eye is located at theright, below the bumper. The fronttowing eye is located on the passengerside behind a flap in the bumperpanel.

Flap removal: Insert finger in recess offlap and pull flap out.

Flap installation: Engage flap at bottomand press in top securely.

We recommend that the vehicle betransported using flat bed equipment.This method is preferable to othertypes of towing.

The vehicle may be towed with allwheels on the ground and the selectorlever in position "N" for distances up to30 miles (50 km) and at a speed not toexceed 30 mph (50 km/h).

To positively avoid a possibility ofdamage to the transmission, however,we recommend to disconnect the driveshaft at the rear axle drive flange onany towing beyond a short tow to anearby garage.

Do not tow with sling-type equipment.Towing with sling-type equipment overbumpy roads will damage radiator andsupports.

Use wheel lift, dolly, or flat bedequipment, with key in steering lockturned to position 0.

Warning!

With the engine not running, there isno power assistance for the brakingand steering systems. In this case, ifis important to keep in mind that aconsiderably higher degree of effortis necessary to brake and steer thevehicle.

To signal turns while being towed withhazard warning flasher in use, turn keyin steering lock to position 2 andactivate combination switch for left orright turn signal in usual manner - onlythe selected turn signal will operate.

Upon canceling the turn signal, theharzard flasher will operate again.

111

Cleaning and Care of the Vehicle

Warning!

Many cleaning products can behazardous. Some are poisonous,others are flammable. Always followthe instructions on the particularcontainer. Always open your car'sdoors or windows when cleaning theinside.

Never use fluids or solvents that arenot designed for cleaning your car.

In operation, your vehicle is subjectedto varying external influences which, ifgone unchecked, can attack the paint-work as well as the underbody andcause lasting damage.

Such damage is caused not only byextreme and varying climaticconditions, but also by air pollution,road salt, tar, gravel and stonechipping. Grease and oil, fuel, coolant,brake fluid, bird droppings, tree resinsetc. should be removed immediately toavoid

paint damage. Frequent washing,however, reduces and/or eliminates theaggressiveness and potency of theabove adverse in-fluences.

More frequent washings are necessaryto deal with unfavorable conditions; forexample, near the ocean, in industrialareas (smoke, exhaust emissions), orduring winter operation.

You should check your vehicle fromtime to time for stone chipping or otherdamage. Any damage should berepaired as soon as possible to preventthe start of corrosion.

In doing so, do not neglect theunderside of the car. A prerequisite fora thorough check is a washing of theunderbody followed by a thoroughinspection. Damaged areas need to bere-undercoated.

Your vehicle has been treated at thefactory with a wax-base rustproofing inthe body cavities which will last for thelifetime of the vehicle. Post-productiontreatment is neither necessary nor

recommended by Mercedes-Benzbecause of the possibility ofincompatibility between materials usedin the production process and othersapplied later.

We have selected car-care products andcompiled recommendations which arespecially matched to our vehicles andwhich always reflect the latest techno-logy. You can obtain MB car-careproducts at your authorized Mercedes-Benz dealer.

Scratches, corrosive deposits, corrosionor damage due to negligent or incorrectcare cannot always be removed orrepaired with the car-care products re-commended here. In such cases it isbest to seek aid at your authorizedMercedes-Benz dealer.

The following topics deal with thecleaning and care of your vehicle andgive important "how-to" information aswell as references to recommendedMB car-care products.

Additional information can be found inthe booklet titled "Car Care".

112

Engine Cleaning

Corrosion protection, such as MBAnticorrosion Wax should be appliedto the engine compartment after everyengine cleaning. Before applying, allcontrol linkage bushings and jointsshould be lubricated. The poly-V-beltand all pulleys should be protectedfrom any wax.

Car Washing

Before washing your vehicle, removeinsect residues. MB Insect Remover isrecommended. Do not use hot water orwash your car in direct sunlight. Useonly a mild car wash detergent, such asMB Autoshampoo.

Thoroughly spray the car with adiffused jet of water. Direct only a veryweak spray towards the ventilationintake. Use plenty of water and rinsethe sponge and chamois frequently.Rinse with clear water and thoroughlywipe dry with a chamois. Do not allowcleaning agents to dry on the finish.Before running the vehicle through anautomatic car wash, fold back

the outside mirrors to prevent them fromgetting damaged.

If the vehicle has been run through anautomatic car wash -in particular one ofthe older installations - rewipe the reces-sed sections in the taillamps (designedto prevent soiling) if necessary. Nosolvents (fuels, thinners etc.) must beused.

In the winter, thoroughly remove alltraces of road salt as soon as possible.When washing the underbody, do notforget to clean the inner sides of thewheels.

Tar Stains

Quickly remove tar stains before theydry and become more difficult toremove. MB Tar Remover isrecommended.

Window Cleaning

Use a window cleaning solution on verydirty or oil-stained windows.

Wiper Blades

Clean the wiper blade rubber with aclean cloth and detergent solution.Replace blades twice a

year; once before and once afterwinter.

Headlamp Cleaning System

The condition of the wiper blades isimportant for satisfactory cleaning ofthe headlamp lenses. We thereforerecommend that the blades beinspected regularly.

Replace damaged wiper blades.

Plastic Parts, Headliner andRubber Parts

Do not use oil or wax on theseparts.

Seat Belts

The webbing must not be treated withchemical cleaning agents. Use onlyclear, lukewarm water and soap. Donot dry the webbing at temperaturesabove 176°F (80°C) or in directsunlight.

Warning!

Do not bleach or dye seat belts asthis may severely weaken them. In acrash they may not be able toprovide adequate protection.

113

Instrument Cluster

Use a gentle dish-washing detergent ormild detergent for delicate fabrics as awashing solution. Wipe with a clothmoistened in lukewarm solution. Donot use scouring agents.

Steering Wheel and GearSelector Lever

Wipe with a damp cloth and drythoroughly or clean with MB LeatherCleaner.

Leather Upholstery

Using aftermarket seat covers orwearing clothing that have thetendency to give off coloring (e.g.when wet etc.) may cause theupholstery to become permanentlydiscolored. By lining the seats with aproper intermediate cover, contact-discoloration will be prevented.

Wipe leather upholstery with a dampcloth and dry thoroughly or clean withMB Leather Cleaner. Exerciseparticular care when cleaningperforated leather as its undersideshould not become wet.

Paintwork, Painted BodyComponents

MB-Gloss Preserver should be appliedwhen water drops on the paint surfacedo not "bead up"; normally in 3 to 5months, depending on climate andwashing detergent used.

MB-Paint-Polish should be applied ifpaint surface shows signs of dirtembedding (i.e. loss of gloss).

MB-Fine Polishing Paste must be usedwhen the paint surface shows signs ofexcessive fading/ chalking due to lackof care etc..

Do not apply any of these products orwax if your car is parked in the sun orif the hood is still hot.

Use the appropriate MB-Touch-UpStick for quick and provisional repairsof minor paint damage (i.e. chips fromstones, car doors etc.).

Light Alloy Wheels

MB-Autoshampoo should be used forregular cleaning of the light alloywheels.

If possible, clean wheels once a weekwith MB-Autoshampoo, using a softsponge and an ample supply oflukewarm water.

If the MB-Autoshampoo does notsatisfactorily clean the wheels, useMB-Protective Agent for Light AlloyWheels for normal cleaning and MB-Cleaner for Light Alloy Wheels forheavier dirt accumulation.Follow instructions on container.

Ornamental Moldings

For regular cleaning and care of verydirty chrome-plated parts, use achrome cleaner.

Automatic Antenna and RearFender Indicators

For trouble-free operation of theautomatic antenna and rear fenderindicators, we recommend to cleanthem periodically.

114

Testing Infrared Remote ControlChecking Batteries:

If the transmit button (1) is pressedlonger than 1 second, the batteryindicator lamp in the transmitter eye(2) briefly illuminates -indicating thatthe batteries are in order.

Change batteries if the indicator lampdoes not come on.

Changing Batteries:

Slide release (3) laterally and pull offbattery cover (4).Change batteries

When inserting new batteries, makesure they are correctly installed.

Slide battery cover onto housing untillocked in place.

Important!

Batteries contain materials that canharm the environment if disposed ofimproperly. Recycling of batteries isthe preferred method of disposal. Fordisposal, please follow manufacturer'srecommendation on battery package.

Replacement battery:Type VARTA V675PX or equivalent.

Synchronizing System:

The system may have to be re-synchronized, if the transmitter iswithout voltage for several minutes.

To synchronize system, aim transmitter(2) at a receiver (5) and briefly presstransmit button (1). Within approx. 30seconds, lock or unlock the car at adoor or the trunk using the master key.

The infrared remote control shouldonce again be operational.

115

Front Head Restraints

Removal:

Push button (1) up to bring the headrestraint to its highest position.

Depress release button (2) beneath theseatback covering material and pullhead restraint up sharply, holding it bythe left head restraint post (viewed indriving direction).

Pull out head restraint completely withboth hands.

Installation:

Push button (1) up for approximately 5seconds.

Insert the head restraint and push itdown to the stop.

Adjust head restraint to the desiredposition.

Warning!

For your protection, drive only withproperly positioned head restraints.

Do not drive the vehicle without theseat head restraints. Head restraintsare intended to help reduce injuriesduring an accident.

For positioning of head restraints referto sections Power Seats, Front, andHead Restraints, Rear in Index.

116

Rear Seat Cushion

Removal: Push in locking tabs (1) (onleft and right side of seat) and pull upseat at the front.

Installation: Slide rear edge of cushionunder the backrest so that both wireloops under the backrest engage at theseat cushion. Push front of cushiondown until it locks in place.

Caution!

Watch out for sharp edges whenremoving or installing the rear seatcushion, to prevent injury.

Manual Closing of Trunk Lid

The trunk lid can be closed manuallyshould a malfunction occur on thepower closing system.

With the trunk lid open:

push sliding switch to position (1),

press eye of latch in (2),

push sliding switch to position (3).

Close trunk lid.

Manual Retraction ofTrunk Lid Handle

The trunk lid handle can be retractedmanually should a malfunction occurwith the automatic system.

Push sliding switch down (1)and to the right (2).

117

Replacing Wiper Blades

For safety reasons, remove key fromsteering lock before replacing a wiperblade, otherwise the motor can suddenlyturn on and cause injury.

Windshield Wiper Blades

Removal:

Pull wiper blade arms upward from therest position to their stop.

Replace wiper blades one at a time toprevent the wiper arms from slidingback to the rest position.

Fold wiper arm forward. Press safetytab down (1), push wiper bladedownward (2) and remove,installation - driver's side:

Press safety tab of new wiper bladedown. Insert wiper blade between thetabs (3) on the wiper arm and slide intoend of wiper arm. Then press safety tabupward until it locks in place.

Installation - passenger side:

Fold wiper arm forward and slidewiper blade into end of wiper arm untilsafety tab locks in place.

Note:

Do not open engine hood with wiperarms folded forward.

Headlamp Wiper Blades

Removal:

Fold wiper arm forward. Push pin (1)and remove.

Installation:

Place wiper blade on wiper arm andpress in pin (1).

118

Manual Release of Fuel Filler Flap

The manual release knob is locatedbehind the right side trunk panel and feltpad.

In case the central locking systemdoes not release the fuel filler flap,pull the manual release knob whilesimultaneously opening the fuel fillerflap.

Emergency Operation of SlidingRoof

The sliding roof can be opened orclosed manually should an electricalmalfunction occur.

Fold back access cover in left sidepanel of trunk with a screwdriver.Insert socket wrench (from tool kit)through opening in panel and place onthe hex-drive of the electric motor.Turn socket wrench (manually) to openor close roof as desired.

To slide the roof closed or to raise theroof at the rear: turn clockwise.

To slide the roof open or to lower theroof at the rear: turn counter-clockwise.

119

Roof Rack

Use only those roof racks approved byMercedes-Benz to avoid damage to thevehicle. Follow manufacturer'sinstallation instructions.

Mount supports only between markingson border of roof which are visiblewhen doors are opened.

Spare Parts Service

All authorized Mercedes-Benz dealersmaintain a stock of original spare partsrequired for maintenance and repairwork. In addition, strategically locatedparts distribution centers provide quickand reliable parts service.

More than 300,000 different spareparts, even for older models, areavailable.

Mercedes-Benz original spare parts aresubjected to the most stringent qualityinspections. Each part has beenspecifically developed, manufacturedor selected for and adapted toMercedes-Benz vehicles.

Therefore, Mercedes-Benz originalspare parts should be installed.

Layout of Poly-V-belt Drive

1 Automatic belt tensioner2 Crankshaft3 Air conditioning compressor4 Fan5 Air pump6 Alternator7 Idler pulley8 Power steering pump9 Coolant pump

For dimensions of the poly-V-belt,see Technical Data in Index.

120

121

Technical Data

122

Identification Plates

When ordering spare parts, pleasespecify vehicle identification andengine numbers.

1 Certification Tag(left door pillar)

2 Identification Tag(lower edge of windshield)

3 Vehicle Identification No.(on cross member beneathfront passenger seat)

4 Engine No.

5 Body No. and Paintwork No.

6 Emission Control Tag

123

Warranty Coverage

Your car is covered under the terms ofthe "warranties" printed in the Owner'sService and Warranty Policy Bookletand your authorized MERCEDES-BENZ dealer will exchange or repairany defective parts in accordance withthe terms of the following warranties:

1. New vehicle limited warranty

2. Emission systems warranty

3. Emission performance warranty

Loss of Owner's Service andWarranty Policy

Should you lose your Owner's Serviceand Warranty Policy Booklet, haveyour authorized MERCEDES-BENZdealer arrange for a replacement. It willbe mailed to you.

124

Technical Data Electrical SystemModel SD 300 (140 134)1 Alternator 14 V/100A

Starter motor 12 V/2.2 kWEngine 603 Battery 12 V/100 AhMode of operation Diesel four strokeNo. of cylinders 6 Technical DataBore 89.00 mm (3.50 in) Weights See certification tagStroke 92.40 mm (3.60 in) Roof load max. 100 kg (220 lb)Total piston displacement 3449 m³ (365.4 cu.in) Trunk load max. 100 kg (220 lb)Compression ratio 22:1

Main DimensionsOutput acc.to SAE J 1349 110 kW/4000rpm Overall vehicle length 5113 mm (201.3 in)

(148 hp/4000 rpm) Overall vehicle width 1886 mm ( 74.3 in)Maximum torque acc. to SAE J 1349 310 Nm/2200 rpm Overall height: 1492 mm ( 58.6 in)

(229 ft-lb/2200 rpm) Wheel base 3040 mm (119.7 in)Maximum engine speed 4250 rpm Track, front 1603 mm ( 63.1 in)Firing order 1-5-3-6-2-4 Track, rear 1576 mm ( 62.0 in)Poly – V - belts length 2120 mm

Rims – TiresRims (light alloy rims) 7 1/² J x 16 H 2 1 The quoted data apply only to the standard vehicle.Wheel offset 51 mm (2.0 in) See an authorized Mercedes-Benz dealer for theSummer tires: corresponding data of all special bodies and specialRadial-ply tires 225/60 R 16 97 V equipment.Winter tires:Radial-ply tires 225/60 R16 97 H M+S

125

Fuels , Coolants, Lubricants etc. - Capacities

Vehicle components and their respective lubricants must matchTherefore use only brands tested and recommended by us.Inquire at your authorized Mercedes-Benz dealer.

Model Capacity Fuels, coolants, lubricants etc.Recommended engine oils

Engine with oil filter 8.0 l (8.5 US qt) Ambient temp. SAE grades

SAE 40 may be used if ambient temperaturesconstantly exceed +86° F ( + 30° C).

Automatic transmission Initial fill: 7.3 l (7.7 US pt) Automatic transmission fluidFluid change: 6.2l US pt 6.6

126

Capacity Fuels, coolants, lubricants etc.

Rear axle 1.4 US qt (1.3 I) Hypoid gear oil SAE 90, 85 W 90

Rear axle with automaticlocking differential (ASD)

1.4 US qt (1.3 I) Hypoid gear oil SAE 90 for limited slipdifferential

Hydraulic system for adap-tive damping system (ADS)

approx. 2.1 US qt (2.0 I) MB Hydraulic fluid

Power steering approx. 1.4 US qt (1.3 I) MB Power steering fluid

Front wheel hubs approx. 2.1 oz (60 g) each High temperature roller bearing grease

Accelerator control linkage Hydraulic fluid

Brake system approx. 0.5 US qt (0.5 I) MB Brake fluid (DOT 4)

Windshield washer andheadlamp cleaning system

approx. 5.3 US qt (5.0 I) MB Windshield washerconcentrate "S"1

Cooling system approx. 11.6 US qt (11.0 I) MB Anticorrosion/antifreeze

Fuel tankincluding a reserve of

approx. 26.4 US gal (100 I)approx. 3.3 US gal (12.5I)

Premium unleaded gasoline: PostedOctane 91 (Average of 96 RON/86 MON)

Air conditioner system R-134a refrigerant and speciallubricant(Never R-12)(selected vehicles - see underhood label)

1 Use MB Windshield Washer Concentrate “S” and water for temperatures above freezing or MB Windshield WasherConcentrate “S” and commercially available premixed windshield washer solvent/antifreeze for temperatures belowfreezing. Follow suggested mixing ratios, see Windshield/Headlamp Washer System in Index.

127

Engine Oils

Engine oils are specifically tested fortheir suitability in our engines.Therefore, use only engine oilsrecommended by Mercedes-Benz.Information on recommended brands isavailable at your authorized Mercedes-Benz dealer.

Brake Fluid

During vehicle operation, the boilingpoint of the brake fluid is continuouslyreduced through the absorption ofmoisture from the atmosphere. Underextremely hard operating conditions,this moisture content can lead to theformation of bubbles in the system thusreducing the system's efficiency.

The brake fluid must therefore bereplaced every two years, preferablyin the spring.

It is recommended to use only brakefluid approved by Mercedes-Benz.Your authorized Mercedes-Benz dealerwill provide you with additionalinformation.

Air Conditioner Refrigerant

Ozone-friendly HFC-134a refrigerantand special lubricating oil is used in theair conditioner system.

Never use R-12 (CFC) or mineral-basedlubricating oil, otherwise damage to thesystem will occur.

128

Diesel Fuels

Use only commercially availablevehicular diesel fuels No. 2 or No. 1(ASTM D 975 No. 2-D or No. 1-D).

If diesel fuels are used with a sulphurcontent exceeding 0.5% by weight,refer to the "Engine Oil Change andOil Filter Service" section. Marinediesel fuel, heating oil or the like mustnot be used.

At very low temperatures the fluidityof No. 2 diesel fuel may becomeinsufficient due to paraffin separation.For this reason the vehicle comesequipped with a fuel preheater. Thefuel preheater only works with thevehicles interior heater operating. Itpermits a trouble free engine operationto a temperature of approximately+ 14°F (-10°C) when using No. 2diesel fuel.

To avoid malfunctions, No. 2 dieselfuel of a lowered cloud point ismarketed during the cold season.At temperatures below + 14°F (-10°C)use winterized or No. 1 diesel fuelonly. If not available, a

certain quantity of kerosene may beadded. Mixing only to be done withinthe cars' fuel tank. Kerosene has to befilled in before the diesel fuel.

Engine power may drop according tothe proportion of kerosene. For thisreason, keep percentage of keroseneadded to the minimum necessitated bythe ambient temperature.

The following table can be used as areference, if adding of kerosenebecomes necessary. The mixing ratiosshown refer to the total mixture.

Ambient temperature

+ 14°F to -4°F (-10°C to -20°C)No. 2 Diesel Fuel: 70%Kerosene: 30%

Ambient temperaturebelow -4°F(-20°C)No. 2 Diesel Fuel: 50%Kerosene: 50%

Even in extreme climatic conditions,the maximum mixture ratio should notexceed 50%.

Adding of kerosene to No. 1 diesel fuelis not recommended even at lowtemperatures.

Warning!

Under no circumstances shouldgasoline be mixed with diesel fuel.Always follow basic safety ruleswhen working with any combustiblematerial. Do not fill the fuel tank ormix diesel fuel and kerosene whensmoking, near an open flame orwhile the vehicle's engine is running.An explosion or fire can result.

129

Therefore the following product isstrongly recommended for use in yourcar: Mercedes-Benz Anticorrosion/Antifreeze Agent.

Before the start of the winter season (oronce a year in the hot southern regions),you should have the anticorrosion/antifreeze concentration checked. Thecoolant is also regularly checked eachtime you bring your vehicle to yourauthorized Mercedes-Benz dealer formaintenance service.

Anticorrosion/antifreeze quantityApprox. freezeprotection

Anticorrosion/antifreeze

-35 ° F(-37 °C)

5.3 US qt (5.0 l)

-49°F 6.3 US qt (6.0 l)(-45°C)

Coolants

The engine coolant is a mixture of waterand anticorrosion/anti-freeze, whichprovides:

• corrosion protection• freeze protection• boiling protection (by increasing

the boiling point).

The cooling system was filled at thefactory with a coolant providing freezeprotection to approx. -22 °F (-30 °C) andcorrosion protection.

The coolant solution must be used yearround to provide the necessary corrosionprotection and increase in the boil-overprotection. You should have it replacedevery 3 years.

To provide the important corrosionprotection, the solution must be at least45% anticorrosion/antifreeze (equals afreeze protection to approx. -22 °F [-30°C]). If you use a solution that is morethan 55% anticorrosion/antifreeze(freeze protection to approx. -49 °F [-45°C]), the engine temperature willincrease due to the lower

Heat transfer capability of the solution.Therefore, do not use more than thisamount of anticorrosion/antifreeze.

If the coolant level is low, water andMB anticorrosion/antifreeze should beused to bring it up to the proper level(have cooling system checked for signsof leakage).

The water in the cooling system mustmeet minimum requirements, which areusually satisfied by normal drinkingwater. If you are not sure about thewater quality, consult your authorizedMercedes-Benz dealer.

Anticorrosion/antifreeze

Your vehicle contains a number ofaluminum parts. The use of aluminumcomponents in motor vehicle enginesnecessitates that anticorrosion/antifreeze coolant used in such enginesbe specifically formulated to protect thealuminum parts. (Failure to use suchanticorrosion/antifreeze coolant willresult in a significantly shortenedservice life.)

130

Consumer Information

This has been prepared as required of allmanufacturers of passenger cars underTitle 49, Code of U.S. FederalRegulations, Part 575 pursuant to the"National Traffic and Motor VehicleSafety Act of 1966".

Uniform Tire Quality Grading

Refer to the tire sidewall for the specifictire grades for the tires with which thisvehicle is equipped.

All passenger car tires must conform tofederal safety requirements in addition tothese grades.

Treadwear

The treadwear grade is a comparativerating based on the wear rate of the tirewhen tested under controlled conditionson a specified government test course.For example, a tire graded 150 wouldwear one and one-half (11/2) times aswell on the government course as a tiregraded 100. The relative performance oftires "depends upon the actual conditionsof their use, however

and may depart significantly from thenorm due to variations in driving habits,service practices and differences in roadcharacteristics and climate.

Traction "A", "B", "C"

The traction grades, from highest tolowest, are "A", "B" and "C" and theyrepresent the tire's ability to stop on wetpavement as measured under controlledconditions on specified government testsurfaces of asphalt and concrete. A tiremarked "C" may have poor tractionperformance.

Warning!The traction grade assigned to thistire is based on braking (straightahead) traction tests and does notinclude cornering (turning) traction.

Temperature "A", "B", "C"The temperature grades are "A" (thehighest). "B" and "C", representing thetire's resistance to the generation of heatand its ability .to dissipate heat when

tested under controlled conditions on aspecified indoor laboratory test wheel.Sustained high temperature can causethe material of the tire to degenerateand reduce tire life, and excessivetemperature can lead to sudden tire fail-ure. The grade "C" corresponds to alevel of performance which allpassenger car tires must meet under theFederal Motor Vehicle Safety StandardNo. 109 Grades "B" and "A" representhigher levels of performance on thelaboratory test wheel than the minimumrequired by law.

Warning!

The temperature grade for this tire isestablished for a tire that is properlyinflated and not overloaded.Excessive speed, underinflation, orexcessive loading, either separately orin combination, can cause excessiveheat build up and possible tirefailure.

131

Problems with your Vehicle

If you should experience a problem with your vehicle, particularly one that you believemay affect its safe operation, we urge you to immediately contact your authorizedMercedes-Benz dealer to have the problem diagnosed and corrected if required. If thematter is not handled to your satisfaction, please discuss the problem with the dealershipmanagement, or if necessary contact the Owner Service Manager at the Mercedes-BenzRegional Office nearest you (see Owner's Service and Warranty Information booklet foraddresses). You may also write directly to us at the following addresses:

In the U.S.A.: Owner Service DepartmentMercedes-Benz of North America Inc.One Mercedes DriveMontvale, NJ 07645-0350

In Canada: Owner Service DepartmentMercedes-Benz Canada Inc.849 Eglinton Avenue EastToronto, Ontario, M4G 2L5

132

For the U.S.A. only.

The following text is published as required of manufacturersunder Title 49, Code of U.S. Federal Regulations, Part 575pursuant to the "National Traffic and Motor Vehicle SafetyAct of 1966".

Reporting Safety Defects

If you believe that your vehicle has a defect which could cause a crash or couldcause injury or death, you should immediately inform the National HighwayTraffic Safety Administration (NHTSA) in addition to notifying Mercedes-Benz of North America Inc..

If NHTSA receives similar complaints, it may open an investigation, and if itfinds that a safety defect exists in a group of vehicles, it may order a recalland remedy campaign. However, NHTSA cannot become involved inindividual problems between you, your dealer, or Mercedes-Benz of NorthAmerica Inc..

To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in Washington, D.C. area) or write to: NHTSA, U.S. Department ofTransportation, Washington, D.C. 20590. You can also obtain other information aboutmotor vehicle safety from the Hotline.

133

Index:

134

ABS 75, 84Activated charcoal filter 25Adaptive damping system (ADS) 86ADS 86Air conditioner refrigerant 127Air outlets 20Airbag 49Alarm system 34Antenna 69, 113Anti-theft alarm system 34Anticorrosion/antifreeze 88,91, 126, 129Antilock brake system (ABS) 84Armrest, front 40Armrest, rear 42ASD 85, 126Ashtrays 64ASR 82Automatic climate control 21Automatic locking differential

(ASD) 85Automatic transmission 73Automatic transmission fluid level,

checking 93

Battery 102Battery not being charged

Charge indicator lamp 14,78Brake fluid 16, 83, 111, 126-127Brake pads worn

Brake pad wear indicator lamp82

Brake warning lampBrake fluid low 83Brake warning lamp test 83

Brakes 15-17, 72, 74-75, 77

Capacities: Fuels, coolants,lubricants etc. 125

Cellular telephone 69Central locking system 30Check regularly and before a long

trip 139Child restraint 40, 47, 51, 53Cleaning and care of the vehicle

111Clock, setting 69Combination switch 55Consumer information 130Coolant level low

Adding coolant 91Low engine coolant levelwarning lamp 81

Coolant level, checking 91Coolant temperature gauge 80 -´81Coolants 129Cruise control 76

Diesel fuels 128Drinking and driving 72Driving instructions 15Driving off 72

Emergency tensioning retractor(ETR) 48

Emission control 87Engine oil consumption 79Engine oil level low

Low engine oil level warninglamp 92

Engine oil level, checking 92Engine oil pressure gauge 78Engine oils 125, 127Engine overheating 80Engine speed limit Overrewing 75Engine, turning off manually 94Exterior lamp failure

indicator lamp 82Exterior lamp switch 57

135

First aid kit 95Fuel consumption gauge 79Fuel filler flap, manual release 118Fuel reserve warning lamp 80Fuel system, bleeding 94Fuses 107

Head restraints, front 35Head restraints, rear 42 - 43Head restraints, removal 115Headlights 57Heated seats 39Hood 90Identification plates 122Indicator lamp symbols 13Instrument cluster 12Interior lighting 62

Jump starting 108

Keys, vehicle 26

Lamps, exterior Fog lamps 57Headlamp, adjusting 105Headlamps 57, 82, 103High mounted stop lamp 107License plate lamp 57, 106Taillamps 57, 106, 112

Layout of poly-V-belt drive 119Lighter 64Low engine oil Level warning

lamp 79Lumbar support 38

Maintenance 4, 8Memory 36Mirrors, adjusting 58-59Multicontour backrest 38

Outside temperature indicator 80

Parking brake 14-16, 18, 64, 72-75,83, 85, 93, 96, 98, 108

Power closing assist for doors andtrunk lid 33

Power seats, front 35Power seats, rear 41Power windows 66Problems with your vehicle 131

Reading lamps 62Rear fender indicators 76Rear passenger compartment

adjustable air outlet 24Rear passenger compartment

climate control 25Rear seat cushion 116Rear view mirrors

Exterior rear view mirrors 59Inside rear view mirror 36 -

37, 44, 58 - 60Rear window defroster 68Rear window sunshade 67Remote control, infrared 27, 114Replacing bulbs 104Roadside assistance 5Roof rack 119

136

Safety guidelines for the seat belt,emergency tensioning retractorand airbag 52

Seat belt warning lamp 82Seat belts and warning system 45Shelf below rear window 68Sliding roof Emergency operation 118Sliding roof operation 65Snow chains 88Spare parts service 118Spare wheel 95SRS malfunction 49Starting and turning off the engine 14Steering lock 54Steering wheel, adjustable 44Storage compartments 63Stowing things in the vehicle 95Sun visors 61Supplemental restraint system

(SRS) 45, 48

Technical data 124Tire inflation pressure 101Tires 16-17, 85, 88, 97, 101, 124,

130Towing the vehicle 110Traveling abroad 87Trunk lamp 95Trunk lid

Manual closing 116Manual retraction of handle 116

Trunk, separately locked 31Turn signals 55- 56

Vanity mirrors 61Vehicle jack 96Vehicle tools 96Warranty coverage 123Washing the car 112Wheels

Alloy wheels 113Rims and tires 97

Wheels, changing 98Windshield/headlamp washer system

Fluid level low 81Washer fluid mixing ratio 56

Winter driving 88Winter driving instructions 18Wiper blades, replacing 117

137

Service and Literature

Your authorized Mercedes-Benz dealer has trainedtechnicians and original Mercedes-Benz parts to serviceyour vehicle properly. For expert advice and quality service,see your authorized Mercedes-Benz dealer.

If you are interested in obtaining service literature for yourvehicle, please contact your authorized Mercedes-Benzdealer.

We consider this to be the best way to obtainaccurate information for your vehicle.

Warning!

To help avoid personal injury, be extremely carefulwhen performing any maintenance work or repairs.Improper or incomplete service may damage the vehicleor its equipment, which may in turn result in personalinjury.

If you have any question about carrying out someservice, turn to the advice of an authorizedMERCEDES-BENZ dealer.

138

139

Check Regularly and Before a Long Trip 1 Fuel SupplyTurn fuel filler cap to the leftand hold on to it until possiblepressure in tank has beenreleased, then remove cap.

2 Tire Inflation Pressure:Check at least every two weeks.For details see Index.

3 Coolant Level:See Index.

4 Windshield Washer System,Headlamp Cleaning System:See Index

5 Engine Oil Level:See Index.

6 Brake Fluid:See Index.

Vehicle Lighting: Check functionand cleanliness. For replacementof light bulbs, see index.

140

What You Should Know at the Gas Station

• Fuel:

Use premium unleaded gasoline: Posted Octane index91 (Average of 96 RON/86 MON).Fuel tank capacity approx. 21.1 US gal (80 l). Thisincludes approx .2.6 US gal (10 l) reserve.Only fill fuel tank until the filler nozzle unit cuts out -do not overfill.

Warning!Gasoline vapor is highly flammable. It burnsviolently and can cause serious injury. Wheneveryou are around gasoline, extinquish all smokingmaterials. Never get sparks, flame or smokingmaterials near gasoline!

• Engine Oil:

Engine oil level check, see Index.Quantity differential between upper and lower dipstickmarking level: 2.1 US qt (2.0 l).Recommended engine oils, see Index.

• Automatic Transmission:

Automatic transmission fluid. For levelchecks refer to Index.

• Coolant:

For normal replenishing, use water (potable water quality).For further information (e.g. anticorrosion/antifreeze), referto Index.

• Spark Plugs:Approved spark plugs, refer to "Technical Data" (also seeIndex).

• Bulbs:High and low beams: HB2 (60/55 W),fog lamps: YC (H3) (55 W),turn signal, standing, side marker and parkinglamps, front: 1157 (21/5 W/32/3 cp),tail, parking, standing and driver's siderear fog lamp: 21/4 W/35/1.2 cp,turn signal lamps, rear: 21 W/32 cp,tail and parking lamps: 5 W,stop lamps: 21 W/32 cp,high mounted stop lamp: H2 (20 W),license plate lamps: 5 W.

• Tire Pressure:For tire pressure, refer to tire pressure inside the fuel fillerflap.

• Air Conditioner:R-l34a refrigerant and special lubricant,refer to "Technical Data" (also see Index).