MMBBBB TRADITIONALCANTILEVER LIFT RANGE

A COMPREHENSIVE RANGE OF TRADITIONAL CANTILEVERS500KG TO 3,000KG CAPACITY

MBB MINIFIX 500 VAN LIFTFULLY AUTOMATIC LIGHTWEIGHT CANTILEVER LIFT SPECIFICALLY DESIGNED FOR PANEL VANS - 500KG CAPACITY

Lightweight AluKolas Platform Large platform 1575mm deep x 1400mm wide, Optional extra deep platform - 1850mm deep x 1400mm wide - suitablefor most high-roof panel vans.

Roll StopSprung-loaded wide roll stop to secure and protect loads whilst on theplatform.

Flashing Warning Lights Operate automatically when the platform is in use

Hinged Bridge Plate Mounted internally to the vehicle floor. Constructed from aluminiumchequer plate and with simple hinge system.

Two-Handed External ControlsEasy to use, mounted on the side of the vehicle with instruction decal.

Platform-Mounted, Heavy Duty Foot ControlsFeature intelligent sequential system allowing operator complete control.

Half-width PlatformsLeaves one door clear for easy access to rear of vehicle without need tolower tail lift.

Tow Ball TUV and CE Marked - detachable swan neck - 50mm ball model. Can beretrofitted to some lifts. Only suitable for rear wheel drive vehicles.

Wanderlead and Radio Remote Controls (not shown)available in addition to external and foot controls. (As shown on page 7)

Standard model voltage capacity platformdepth x width

maximum floorheight

weight from

Minifix 500 12 volt only 500kg1575mm x 1400mm

1850mm x 1400mm780mm

156kg

165kg

Fitting kits to suit specificmodels allows fast and accuratefitment.

AApppprroovveedd bbyy lleeaaddiinnggmmaannuuffaaccttuurreerrss aass lliisstteedd::--Citroën Jumper (relay)Fiat DucatoFord TransitIveco Daily

Mercedes-Benz Sprinter200/300/400Nissan Interstar and PrimasterVauxhall/Opel Movano andVivaroPeugeot BoxerRenault Master and TraficVolkswagen Crafter 28/35/50

Suitable for most Panel Vans

Probably the lightest model on the market. Features one lift cylinder and one double-acting tilt cylinder, which isintegrated in the aluminium platform. Special arrangement of thecylinder permits a very shallow installation.

STANDARD FEATURES

OPTIONAL FEATURES

MBB 1000 ATHLET quattro LIGHTWEIGHT CANTILEVERROBUST 4-CYLINDER CANTILEVER - 1000KG CAPACITYDESIGNED FOR BOX BODIES 6.5 TONNE GVW AND ABOVE

KTL Coated Lift Frame and 3-piece Underrun Bar for protection against corrosion

‘Made to Measure’ Lightweight Aluminium PlatformsStandard: Alustar - (Options - AluLite and Alu-Kolas)

Intelligent Heavy Duty foot controls Sequential system allows operator complete control

2-handed external control box with translucent lighting Housed in water-proof box - lighting permits safe night-time operation.

Steel PlatformKTL Coated steel platforms

Roll StopsSprung-loaded or manual roll stops to secure and protect loads whilst onthe platform.

Flashing Warning Lights Operate automatically when the platform is in use

Hook-in Side RampsAvailable in three sizes to suit individual applications

Detachable Safety GatesSide and all-round gates available for extra protection to operator andload.

Battery ProtectorSee Traditional Cantilever Options for photo and details

Rear Closure Platforms Eliminate the need for regular rear closure. Optional sealing kit withArm Stops to protect lift against body damage

Lightweight, Robust 4-cylinder Cantilever The MBB PALFINGER 1000 ATHLET quattro offers a lightweightcantilever lifting solution with 2 lift cylinders and 2 double-actingtilt cylinders for maximum performance. Powerpack is stowed in thebeam for added protection. Popular rear closure platforms increasevehicle payload.

A best selling lift throughout Europe for the past 10 years.

It’s reliable, competively priced, lightweight for maximum payloadand has a well-proven track record for durabilty.

STANDARD FEATURES

OPTIONAL FEATURES

modelcapacityat loadcentre

suitable forvehicles

made to measurealuminiumplatforms

steel platform

maximumfloor height

weight fromaluminium/steel

min/maxdepth

min/maxwidth depth x width

Athlet quattro1000kg

at 600mmfrom 6.5 to12.9 tonnes

min 1200mmmax 1850mm

min 1500mm50mm

increments upto 2550mm

1509/1809mm xup to 2550mm

1210mm 272kg/340kg

MBB TRADITIONAL CANTILEVERS MODEL RANGES

K RANGE - STANDARD CANTILEVERAVAILABLE - 500KG - 750KG - 1000KG - 1500KG - 2000KG - 2500KG - 3000KG CAPACITIES

KL RANGE - LIGHT CANTILEVERAVAILABLE - 1500KG CAPACITIES

CAR LIFTAVAILABLE - 3000KG CAPACITIES

KS RANGE - SHORT OVERHANGAVAILABLE - 1500KG - 2000KG CAPACITIES

KK RANGE - DRAW BARAVAILABLE - 1500KG - 2000KG CAPACITIES

MBB TRADITIONAL CANTILEVERSSTANDARD FEATURES

K-Basic Control System- Easy to install - Low maintenance required- User-friendly - Illuminated control box- optional sealed pc-board +

ground tilting.

Double-Acting Hydraulictilting Cylinders A very important part in ensuringthe correct movement andstrength of the lift. These aremanufactured in-house by MBBPalfinger to ensure high qualityperformance. Power opening andpower closing cylinders are strongand reliable hence the platformopens and shuts easily, even onthe steepest of inclines.

Platform Ground RollersProvide increased protectionagainst wear and tear.

Cylinder CoversProtect cylinders against damagefrom impact and scratching.

Cylinder flow control valvesEvery cylinder is fitted with flowcontrol valves which safely controlthe descent of a fully loadedplatform, even in the event of aburst hose in the hydraulic circuit.

PlatformsWide choice of platformsavailable - see next page‘‘PPllaattffoorrmm OOppttiioonnss’’ for full detailsof different construction materialsand sizes available (including‘made to measure’ widths , rampsand roll stops etc.

KTL CoatingLifting mechanisms and steelplatforms are protected with KTLcoating as standard. KTL protectsagainst rust and minimisesdamage caused by stone chippingand prevents rust spreading. KTLhas been salt-spray tested incompliance with EN Regulations.

EExxtteerrnnaall CCoonnttrrooll BBooxxFactory pre-wired, weather proof,corrosion resistant control boxhousing 2-handed lift controls.

Translucent instructions lit by aninterior light making it possible tooperate the lift safely - even inthe dark!

‘Intelligent Foot Controls’MBB foot controls are able todistinguish between contact withthe operator’s foot and the load.Should goods be resting on thefoot controls, the platformremains static.

Safety valveSafety valves are fitted to alllifting and tilting cylinders asstandard on all models.

Clever construction ensuresbearings well greasedChromium-free pivot pins aresolid and not weakened bylubrication holes. 12 greasenipples for bearings are locatedon the exterior of the cylinderends to ensure direct delivery ofgrease to the bearings

The Power Pack is housed inthe beamProtecting it from unnecessarydamage. It can be pulled outeasily for inspection andmaintenance. Noise from themain pump is greatly reduced -especially important when the liftis being used at night.

Underrun Bar (not KK models)CE approved, three-piece KTLfinish coated underrun bar.

See lift options for underrun barfitted to KK models.

MBB TRADITIONAL CANTILEVERSPLATFORM OPTIONS

Made-to-Measure Half and Third Width Plaforms(500K, 750K, 1000K)Allows clear access to rear ofvehicle without need to lower thetail lift. Particularly useful forrefrigerated bodies.Only available for aluminiumplatforms - not Athlet Quattro.

Rear Closure Platform(all models)Rear closure offers additionalweight saving and security.Platform sealing kit hasintegrated floor stop for moreefficient operation.

Folding Aluminium Platform(500K, 750K)AluKolas folding platformsuitable for dropside vehicles.

Roll Stops(all models)Foot operated, sprung loaded ormanual, two piece aluminiumrolls stops to provide extra loadsecurity.

Alustar Platform(standard aluminium platformexcept for 3000K)Versatile, lightweight, aluminiumtreadplate surface, assists in theprevention of slipping. Not ofmodular build, and can thereforebe cut to meet the exactrequirements of the customer.

AluLite Platform - NEW(500K, 750K, 1000K, 1500KL)Lightest aluminium platform inthe range, for increased payload.

AluKolas Platform(all except 3000K and car lift))AluKolas is market leader ininnovative production ofaluminium platforms. Usinghybrid plasma welding processsections neatly welded withminimum heat = excceptionallyrobust platform without warping.

Alu Liftal Platform(2500K, 3000K)Heavy Duty, lightweight,aluminium planked platform.

LED Flashing Lights(option)Located on the platform theyoperate automatically whenplatform is in use to ensure thelift is fully visible at all times.

Steel Platform(all models)Heavy duty, KTL finish coatedprotecting against corrosion.

Detachable Side RampsAvailable in three sizes to suitindividual applications

Non-Slip Platform Surface (all platforms)Synthetic rubber coating appliedto specially prepared platformsurface to ensure strong bond.Reduces noise levels duringloading and unloading, whilstproviding an anti-slip surface foroperator safety.

MBB TRADITIONAL CANTILEVERSOPTIONS

Speedy diagnostic faultfinding - K-plus control systemKK11--pplluuss - fully electronic sensorcontrol and electronic memoryKK--pplluuss - electronic sensor controlBoth allow the engineer, in theevent of a lift failure, to quicklyidentify the problem - reducingdowntime and repair costs.

Battery Protector (all models)Avoids the inconvenience of a flatbattery due to tail lift use. Itgives an audible warning as thevoltage of the battery falls andcuts out after a second warning,ensuring there is sufficient powerto start the vehicle engine.

Lifting Underrun Bars - KKmodels onlyCompatible with draw barapplications. Mechanical orHydraulic lifting available.

Internally-Mounted ControlsFlush fitting internally mountedthree button control (lift, lowerand tilt) may be fitted to the rearinside of the body. The flush fitprevents damage from trolleysetc. Popular for use onrefrigerated bodies.

Detachable Steel Safety GatesAvailable for sides only or ‘all-round’ models. KTL protected.

The use of safety gates is highlyrecommended by the HSE togreatly reduce the risk of goodsand/or the operator falling fromthe platform.

Wanderlead Controls (all models including Minifixand Athlet)Two button (lift and lower) andthree button (lift, lower and tilt)wanderlead controls available.

Radio Remote Control (all models including Minifixand Athlet)Allows the operator morefreedom to move around

Bolted Mounting PlatesAlternative to pre-weldedmounting plates, preferred bysome users to enable the lift tobe easily transferred to anothervehicle chassis.

Pre-Welded Mounting PlatesFor quick and easy fitting to thevehicle

Hydraulic and MechanicalSupport Jacks(K series lifts only)Used to stablise vehicles whenloading.

Usually used on deep platformsfor large and valuable loads.

Key SwitchProvides extra security andprevents the lift being operatedby unauthorised people.

Rear Light holderFor easier and quicker installationof rear lights.

TECHNICAL DATA FOR MBB TRADITIONAL CANTILEVERSPLATFORM OPTIONS FOR K/KL/KS/KK SERIES 500KG - 3000KG CAPACITIES

RATCLIFF PALFINGER Ltd

Bessemer RoadWelwyn Garden CityHertfordshire AL71ET, United KingdomTel: +44 (0)1707 325571 - Fax: +44 (0)1707 327752Info@ratcliffpalfinger.co.uk

The RATCLIFF PALFINGER policy is one of continuous product development and the Company therefore reserves the right to alter product or component specifications without notice

www.ratcliffpalfinger.co.uk

04/11Subject to setting and printing errors

modelcapacityat loadcentre

suitable forvehicles

made to measurealuminium platforms

steel platform

maximumfloor height

weight fromaluminium/steel

min/maxdepth

min/maxwidth

depth x width (max)

500K/750K 500Kg/750Kgat 600mm

3.5 tonnes to7.5 tonnes

min 1200mm

max 1850mm

as required in50mm

increments upto 2550mm

1209mm x 2550mm1509mm x 2550mm

1263mm 232Kg/313Kg

1000K 1000Kgat 700mm

7.5 tonnes to18 tonnes

min 1200mm

max 2400mm

as required in50mm

increments upto 2550mm

1209mm x 2550mm1509mm x 2550mm1809mm x 2550mm

1546mm 391Kg/524Kg

1500KL 1500kgat 600mm

from 7.5tonnes

min 1200mm

max 2400mm

as required in50mm

increments upto 2550mm

1209mm x 2550mm1509mm x 2550mm1809mm x 2550mm

1546mm 454Kg/551Kg

1500K/KS/KK 1500Kgat 1000mm

from 7.5tonnes

min 1200mm

max 2600mm

as required in50mm

increments upto 2550mm

1209mm x 2550mm1509mm x 2550mm1809mm x 2550mm2109mm x 2550mm

1793mm 557Kg/660Kg

2000K/KS/KK 2000Kgat 750mm

from 12tonnes

min 1200mm

max 2600mm

as required in50mm

increments upto 2550mm

1509mm x 2550mm1809mm x 2550mm2109mm x 2550mm

1793mm 542Kg/645Kg

2500K 2500Kgat 750mm

from 16tonnes

min 1200mm

max 2600mm

as required in50mm

increments upto 2550mm

1509mm x 2550mm1809mm x 2550mm2109mm x 2550mm2409mm x 2550mm

1444mm 566Kg/668Kg

3000K 3000Kgat 800mm

from 16tonnes

min 1200mm

max 3000mm

as required in50mm

increments upto 2550mm

2009mm x 2550mm2209mm x 2550mm2409mm x 2550mm

1554mm 730Kg/903Kg

3000K(car lift)

3000Kgat 800mm

please discusswith Sales

Office

one size onlysteel aluminium

4000mm (including ramps) x 2300mm1554mm

Approximately

1000Kg

KK Standard Cantilever

KKLL Light Cantilever

KKSS for vehicle with short overhang

KKKK for draw bar trailers