matmÄssig au - ikea€¦ · children and vulnerable people safety ... • warning: unattended...

MATMÄSSIGAU

AU NZ

ENGLISHPlease refer to the chapter IKEA GUARANTEE for contact details ofthe after sales customer service centre.

AU NZ ENGLISH 4

LANGUAGE

COUNTRY

ContentsSafety information 4Conditions of Use 6Safety instructions 6Product description 9Daily use 10Hints and tips 11Care and cleaning 11

Troubleshooting 12Technical data 13Installation 15Electrical connection 16Gas connection 18Environmental concerns 23IKEA guarantee 23

Subject to change without notice.

Safety information

Before the installation and use of the appliance, carefully readthe supplied instructions. The manufacturer is not responsible ifan incorrect installation and use causes injuries and damages.Always keep the instructions with the appliance for futurereference.

Children and vulnerable people safety• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory ormental capabilities or lack of experience and knowledge ifthey have been given supervision or instruction concerningthe use of the appliance in a safe way and understand thehazards involved.

• Children between 3 and 8 years of age and persons withvery extensive and complex disabilities shall be kept awayunless continuously supervised.

• Children of less than 3 years of age should be kept awayunless continuously supervised.

• Do not let children play with the appliance.• Keep all packaging away from children and dispose of it

appropriately.• Keep children and pets away from the appliance when it

operates or when it cools down. Accessible parts are hot.

ENGLISH 4

• If the appliance has a child safety device, it should beactivated.

• Children shall not carry out cleaning and user maintenance ofthe appliance without supervision.

General Safety• WARNING: The appliance and its accessible parts become

hot during use. Care should be taken to avoid touchingheating elements.

• Do not operate the appliance by means of an external timeror separate remote-control system.

• WARNING: Unattended cooking on a hob with fat or oil canbe dangerous and may result in fire.

• NEVER try to extinguish a fire with water, but switch off theappliance and then cover flame e.g. with a lid or a fireblanket.

• CAUTION: The cooking process has to be supervised. A shortterm cooking process has to be supervised continuously.

• WARNING: Danger of fire: Do not store items on the cookingsurfaces.

• Metallic objects such as knives, forks, spoons and lids shouldnot be placed on the hob surface since they can get hot.

• Do not use a steam cleaner to clean the appliance.• If the supply cord is damaged, it must be replaced by the

manufacturer, the Authorised Service Centre or similarlyqualified persons in order to avoid a hazard.

• Where the appliance is directly connected to the powersupply, an all-pole isolating switch with a contact gap isrequired. Complete disconnection in compliance with theconditions specified in overvoltage category III must beguaranteed. The earth cable is excluded from this.

• When you route the mains cable, make sure that the cabledoesn't come into direct contact (for example using insulating

ENGLISH 5

sleeving) with parts that can reach temperatures of more than50°C above room temperature.

• WARNING: Use only hob guards designed by themanufacturer of the cooking appliance or indicated by themanufacturer of the appliance in the instructions for use assuitable or hob guards incorporated in the appliance. Theuse of inappropriate guards can cause accidents.

Conditions of Use

This appliance is intended to be used inhousehold and similar applications such as:• Farm houses

• By clients in serviced apartments, holidayapartments and other residential typeenvironments.

Safety instructions

Installation

Warning! The appliance must beinstalled by the authorisedinstaller.

• Remove all the packaging.• Do not install or use a damaged

appliance.• Follow the installation instructions

supplied with the appliance.• Keep the minimum distance from other

appliances and units.• Always take care when moving the

appliance as it is heavy. Always usesafety gloves and enclosed footwear.

• Seal the cut surfaces with a sealant toprevent moisture to cause swelling.

• Protect the bottom of the appliance fromsteam and moisture.

• Do not install the appliance adjacent toa door or under a window. This preventshot cookware falling from the appliancewhen the door or the window is opened.

• If the appliance is installed abovedrawers make sure that the space,between the bottom of the appliance

and the upper drawer, is sufficient for aircirculation.

• The bottom of the appliance can get hot.Make sure to install a non-combustibleseparation panel under the appliance toprevent access to the bottom.Refer to the Assembly Instructions.

Electrical Connection

Warning! Risk of fire and electricshock.

• All electrical connections should be madeby the authorised installer.

• The appliance must be earthed.• Before carrying out any operation make

sure that the appliance is disconnectedfrom the power supply.

• Make sure that the parameters on therating plate are compatible with theelectrical ratings of the mains powersupply.

• Make sure the appliance is installedcorrectly. Loose and incorrect electricitymains cable or plug (if applicable) canmake the terminal become too hot.

• Use the correct electricity mains cable.

ENGLISH 6

• Do not let the electricity mains cabletangle.

• Make sure that a shock protection isinstalled.

• Use the strain relief clamp on the cable.• Make sure the mains cable or plug (if

applicable) does not touch the hotappliance or hot cookware, when youconnect the appliance to the nearsockets.

• Do not use multi-plug adapters andextension cables.

• Make sure not to cause damage to themains plug (if applicable) or to the mainscable. Contact our Authorised ServiceCentre or an electrician to change adamaged mains cable.

• The shock protection of live andinsulated parts must be fastened in sucha way that it cannot be removed withouttools.

• Connect the mains plug to the mainssocket only at the end of the installation.Make sure that there is access to themains plug after the installation.

• If the mains socket is loose, do notconnect the mains plug.

• Do not pull the mains cable to disconnectthe appliance. Always pull the mainsplug.

• Use only correct isolation devices: lineprotecting cut-outs, fuses (screw typefuses removed from the holder), earthleakage trips and contactors.

• The electrical installation must have anisolation device which lets you disconnectthe appliance from the mains at all poles.The isolation device must have a contactopening width of minimum 3 mm.

Gas connection

Warning! Risk of fire andexplosion

• All gas connections should be made bythe authorised installer.

• Before installation, make sure that thelocal distribution conditions (nature of the

gas and gas pressure) and theadjustment of the appliance arecompatible.

• Make sure that there is air circulationaround the appliance.

• The information about the gas supply ison the rating plate.

• This appliance is not connected to adevice, which evacuates the products ofcombustion. Make sure to connect theappliance according to currentinstallation regulations. Pay attention torequirements regarding adequateventilation.

Use

Warning! Risk of injury, burnsand electric shock.

• Remove all the packaging, labelling andprotective film (if applicable) before firstuse.

• This appliance is for household use only.• Do not change the specification of this

appliance.• Make sure that the ventilation openings

are not blocked.• Do not let the appliance stay unattended

during operation.• Set the cooking zone to “off” after each

use.• Do not put cutlery or saucepan lids on

the cooking zones. They can become hot.• Do not operate the appliance with wet

hands or when it has contact with water.• Do not use the appliance as a work

surface or as a storage surface.• When you place food into hot oil, it may

splash.Warning! Risk of fire andexplosion

• Fats and oil when heated can releaseflammable vapours. Keep flames orheated objects away from fats and oilswhen you cook with them.

• The vapours that very hot oil releasescan cause spontaneous combustion.

ENGLISH 7

• Used oil, that can contain food remnants,can cause fire at a lower temperaturethan oil used for the first time.

• Do not put flammable products or itemsthat are wet with flammable products in,near or on the appliance.

Warning! Risk of damage to theappliance.

• Do not keep hot cookware on the controlpanel.

• Do not let cookware to boil dry.• Be careful not to let objects or cookware

fall on the appliance. The surface can bedamaged.

• Do not activate the cooking zones withempty cookware or without cookware.

• Do not put aluminium foil on theappliance.

• Use only stable cookware with thecorrect shape and diameter larger thanthe dimensions of the burners.

• Make sure cookware is centrallypositioned on the burners.

• Make sure the flame does not go outwhen you quickly turn the knob from themaximum to the minimum position.

• Use only the accessories supplied withthe appliance.

• Do not install a flame diffuser on theburner.

• The use of a gas cooking applianceresults in the production of heat andmoisture. Provide good ventilation in theroom where the appliance is installed.

• Prolonged intensive use of the appliancemay call for additional ventilation, forexample opening of a window, or moreeffective ventilation, for exampleincreasing the level of mechanicalventilation where present.

• This appliance is for cooking purposesonly. It must not be used for otherpurposes, for example room heating.

• Do not let acid liquids, for examplevinegar, lemon juice or limescaleremover, touch the hob. This can causematt patches.

• Discoloration of the enamel or stainlesssteel has no effect on the performance ofthe appliance.

• Do not spray aerosols in the vicinity ofthis appliance while it is in operation.

• Do not place articles on or against theappliance.

• Do not modify the appliance.• Do not use or store flammable materials

in the appliance storage drawer or nearthe appliance.

• Do not use the appliance as a spaceheater.

• Do not allow large cookware tooverhang the cooktop onto the adjacentworktop. This will cause scorching to theworktop surface.

• Do not put cooking pots or pans close tothe controls.

• This appliance complies with therequirements of Australian StandardAS5263.1.1.

Care and cleaning

Warning! Do not remove thebuttons, knobs or gaskets fromthe control panel. Water may getinside the appliance and causedamage.

• Clean the appliance regularly to preventthe deterioration of the surface material.

• Deactivate the appliance and let it cooldown before you clean it.

• Disconnect the appliance from theelectrical supply before maintenance.

• Do not use water spray and steam toclean the appliance.

• Clean the appliance with a moist softcloth. Only use neutral detergents. Donot use any abrasive products, abrasivecleaning pads, solvents or metal objects.

• Do not clean the burners in thedishwasher.

ENGLISH 8

Service• To repair the appliance contact an

Authorised Service Centre.• Use original spare parts only.

Disposal

Warning! Risk of injury orsuffocation.

• Contact your municipal authority forinformation on how to discard theappliance correctly.

• Disconnect the appliance from the mainssupply.

• Cut off the mains electrical cable close tothe appliance and dispose of it.

• Flat the external gas pipes.

Product description

Cooking surface layout

9

5

8

7

6

2 3 4

1

1 Multi Crown burner2 Semi Rapid burner3 Semi Rapid burner4 Auxiliary burner5 Removable pan supports6 Auxiliary burner control knob7 Semi Rapid burner control knob8 Semi Rapid burner control knob9 Multi Crown burner control knob

Burner control knobThe hob burner control knobs are on theright side of the hob.

Symbol Descriptionoff position

there is maximum gassupply / ignition setting

there is minimum gas sup-ply

to show the position of theburner

ENGLISH 9

Daily use

Warning! Refer to Safetychapters.

Ignition of the burner

Always ignite the burner beforeyou place the pots or pans.

To ignite the burner:1. Push the control knob and turn it

anticlockwise to the maximum positionmarked with .

2. Once lit keep the control knob pushedfor about 5 sec. As a result,thermocouple heats up, and the safetydevice switches off. If you do not pushthe knob, the gas supply is interrupted.

3. When you light the flame, you canadjust it.

If the burner does not ignite,after a few attempts, check if thecrown and its cap are in correctpositions.

1

2

3

4

5

1 Burner cap2 Burner crown3 Injector4 Thermocouple5 Ignition candle

Warning! Do not keep thecontrol knob pressed for morethan 15 seconds. If the burnerdoes not light after 15 seconds,release the control knob, turn itinto the off position, and wait forat least 1 minute before trying tolight the burner again.

If there is no spark when thecontrol knob is pushed then theremay be a fault with the powersupply. Refer to thetroubleshooting section.

Warning! Be careful when youuse open fire in the kitchenenvironment. The manufacturerdeclines any responsibility incase of misusing the flame.

If the burner accidentally goesout, turn the control knob to theoff position and wait for at least1 minute before trying to light itagain.

When you switch on the mainsafter installation or a power cut,the spark generator activatesautomatically.

The hob is supplied with theprogressive valves. They makethe flame regulation moreprecise.

Turning the burner offTo put the flame out, turn the relevantcontrol knob to the symbol .

ENGLISH 10

Warning! Always turn the flamedown or switch it off before youremove the pans from the burner.

Hints and tips


Energy saving• If it is possible, always put the lids on the

cookware.• When the liquid starts to boil, turn down

the flame to barely simmer the liquid.

Diameters of cookwareUse pots and pans with bottom fitting thesize of burner used.

BurnerMinimum di-

ameter ofpots and pans

Maximum di-ameter of pots

and pansMulti

Crown 180 260

BurnerMinimum di-

ameter ofpots and pans

Maximum di-ameter of pots

and pansAuxiliary 80 180

Back left(Semi-rap-

id)120 240

Back right(Semi-rap-

id)120 240

The bottom of the cookware should be asthick and flat as possible.

Care and cleaning


General information

Warning! Switch the applianceoff and let it cool down beforeyou clean it.

Warning! Do not clean theappliance with steam blasters orhigh-pressure cleaners.

Warning! Do not use abrasivecleaners, steel wool pads oracids. They damage theappliance.

To remove any food remains, wash theenamelled elements, caps, and crowns, withwarm soapy water.Wash stainless steel elements with water,and dry with a soft cloth.This model is equipped with an electricalignition. To avoid problems with lightning,keep the ceramic "candle" with electrodeclean.

ENGLISH 11

Do not put the pan supports in adishwasher. Wash themmanually and dry with a softcloth. After cleaning, make surethat the pan supports are incorrect position.

To check the conditions of thegas supply pipe and the pressureadjuster, contact the After SalesService Provider. The service isnot free of charge.

Removing pan supportsFor easier cleaning, pan supports can beremoved from the hob. Lift up the pansupports keeping them in horizontal

position and with the right order as shownin the graphic.

1

2

2

1

Troubleshooting


ENGLISH 12

What to do if...

Problem Possible cause Remedy

There is no spark when light-ning the gas.

There is no electrical supply. Check if the unit is pluggedin and the electrical supply isswitched on.

There is no electrical supply. Check the house electric in-stallation fuse.

Burner cap and crown areplaced incorrectly.

Check if the burner cap andcrown are placed correctly.

The flame is extinguishes im-mediately after lightning.

Thermocouple is not heatedenough.

After lightning the flame,keep the knob pushed forabout 5 seconds.

The gas ring burns unevenly. Burner crown is blocked withfood remains.

Check if the main injectorand the burner crown arenot blocked with food re-mains.

If there is an error, first try to find a solutionto the problem yourself. If you cannot find asolution to the problem yourself, contactyour IKEA store call centre. You can find afull list of IKEA appointed contacts at theend of this manual.

If the appliance is misusedwrongly or installed not byauthorised technician, the serviceis not free of charge, even duringthe warranty period.

Technical data

Hob dimensions

Width 595 mm

Depth 510 mm

Built in height 40 mm

Other technical data

Class Appliance: 3Appliance Category: -Appliance gas supply: Naturalgas 1.13 kPaThis appliance is designed foruse with natural gas but can beconverted for use with other gastype according to table below.

ENGLISH 13

TOTAL POWERNatural Gas at 1.13kPa supplywith 1.0kPa test point pressure: 37.4 MJ/h

Gas replacement 2.75kPa sup-ply with Universal LPG at

2.60kPa test point pressure:27,9 MJ/h

Gas connection: R 1/2"

Burner type Injector mark Injector size(mm)

Gas consump-tion MJ/h by-pass

NATURAL GAS 1.0 kPa(test point pressure)

Multi Crown 175 1.75 14.3 57

Semi-rapid(medium) 135 1.35 9.0 35

Auxiliary(small) 100 1.00 5.1 32

U-LPG 2.60 kPa(test point pressure)

Multi Crown 96A 0.96 12.0 57

Semi-rapid(medium) 71 0.71 6.4 35

Auxiliary(small) 50 0.50 3.1 32

Rating Plate

703.688.39

Made In Italy

© Inter IKEA Systems B.V. 1999

TYPE: H6FF4MM0-G/VI PNC 949640528 00

S.N.: 00000000 220-240 V ~ 50/60 Hz

MOD: MATMÄSSIG

18 MADE IN ITALY

AU-NZ

GAS: NG/LPG TEST kPa 1.0/2.60APP NO: AGA 8654 G to AS/NZS 5263.1.1IKEA of Sweden AB

SE - 343 81 Älmhult PQ

M1

12

2

21552

Max Power = 6W

Supply Pressure NG: 1.13-5.0kPa LPG: 2.75-3.5kPa

H.G.C: 37,4 / 27,9 MJ/h

1223333394964052859099

ENGLISH 14

The graphic above represents the ratingplate of the appliance, without serialnumber which is generated dynamicallyduring the production process. The ratingplate is located below the surface of thecasing.Dear Customer, please apply the stickerwhich you can find in the plastic bag

attached to the hob packaging. As a result,in case you need our assistance, the AfterSales Service Provider can identify preciselyyour hob. Thank you for your help.

Installation


Caution! Information forauthorised installer only.

Warning! Use only partsprovided with the product. Useonly original spare parts.

The manufacturer is not responsible for anyinjury to persons and pets or damage toproperty caused by a failure to comply thefollowing requirements.

Caution! During the installation,you must refer to the AssemblyInstructions.

Warning! Installation processmust follow the laws, ordinances,directives, and standards,electrical safety rules, andregulations, proper recycling inaccordance with the regulations,in force in the country of use.

Depending on the AssemblyInstructions, keep the minimumdistances between the applianceand other units.

Caution! This appliance shouldbe installed by a authorisedinstaller to comply with therequirements of AS/NZS 5601current edition.

Protect the cut surfaces of the worktopagainst moisture using a suitable sealantincluded in the product in additional bag.Seal the appliance to the worktop with nogap. Do not use silicon sealant between the

ENGLISH 15

appliance and the worktop. Do not installthe appliance next to the doors and underwindows. Otherwise, the hot cookware mayfall off the pan supports.Clearances to combustible surfaces

130 mm

110 mm

100 mm

Adjacent walls, cupboards and protectionfor combustible materials: Ensure that the

appliance is installed in accordance withclauses 6.2.5 and 6.10.1.1 of AS/NZS5601.1, or clauses 6.9.1 and 6.9.5 ofAS/NZS 5601.2 with regard to clearancesto combustible surfaces and materials, andclearances to rangehoods and exhaustfans. To ensure clearances of 200mm fromburners to vertical combustible surfacesobserve the minimum distance requirementsshown in Figure. Clearances to combustiblesurfaces wmay be reduced if combustiblesurfaces are protected in accordance withclause 6.10.1.2 of AS/NZS 5601.1, orclause 6.9.2 of AS/NZS 5601.2

For installation into a standard600mm width benchtop theclearance specified can not beachieved and combustiblesurfaces must be protected inaccordance with the aboveclauses.

Electrical connection


Connection cable


Warning!The appliance must be earthed.

Warning!Risk of injury from electricalcurrent.

• The electrical mains terminal is undervoltage.

• Make sure that the electrical mainsterminal is free of voltage.

• Loose and inappropriate plug andsocket connections. May overheat theterminal.

• Make sure that the clamping connectionsare installed correctly.

• Secure the cable with the strain reliefclamp.

Before connecting, check that the nominalvoltage of the appliance stated on therating plate, corresponds to the availablesupply voltage. Also, check the powerrating of the appliance and make sure thatthe wire is suitably sized to suit theappliance power rating. Refer to theTechnical data chapter.

ENGLISH 16

Electrical Requirements

You can check the parameters ofadjustment setting for thisappliance on the rating plate.Refer to the Technical datachapter.

The manufacturer declines anyliability if these safety measuresare not observed.

The appliance must be connected to a220-240 V 50/60 Hz AC electrical supply.Before activating the appliance, make surethe electrical supply voltage is the same asthat indicated on the rating plate. Therating plate is located below the surface ofthe casing.The appliance is supplied with a standard7.5 amp service cord terminated by a 3-pinplug for connection to a standardhousehold socket.You must install the plug. The wires in themains lead are coloured in accordance withthe following code:Green and yellow - EarthBlue - NeutralBrown - Live1. Connect the green and yellow (earth)

wire to the terminal in the plug which ismarked with the letter 'E' or the earthsymbol , or coloured green andyellow.

2. Connect the blue (neutral) wire to theterminal in the plug which is markedwith the letter 'N' or coloured black.

3. Connect the brown (live) wire to theterminal in the plug which is markedwith the letter 'L' or coloured red.

There must be no cut or stray strands ofwire present. The cord clamp must becorrectly attached on the outer sheath.

body

220-240Vignition box

to burner spark plugs

knobignition

switches

ENL

DANGER220-240 volts ACDisconnect from supply before

removing panel

To prevent contact between thecable and the appliance belowthe hob use the clamps which areon the side of the cabinet.

Replacement of the connection cable

Warning! To replace theconnection cable, the technicianmust have a specific equipment.

In this case, only cable type H05SS-F T180must be used. The cable section must besuitable to the voltage and the workingtemperature. The yellow and green earthwire 2 must be approximately 2 cm longerthan the brown or black phase wire 1 .

1

2

ENGLISH 17

Gas connection



Connection to main pipe

Warning! This appliance is notconnected to a combustionproducts evacuation device.

Before you proceed with theinstallation, make sure that thelocal distribution conditions,nature of the gas and gaspressure, and the adjustment ofthe appliance are compatible.

The installation must be compliant with thecurrent local gas fitting regulations and withAS/NZS 5601.1 Gas Installations Part 1:General Installations, and AS/NZS 5601.2Gas Installations Part 2: LP Gas installationsin caravans and boats for non-propulsivepurposes, or the relevant installation codefor gas appliances in your country.Complying with the local regulations, theconnection of the cooktop to the gas pipenetwork or gas cylinder must be made bymeans of a rigid copper or steel pipe withfittings, or by means of a continuous surfacestainless steel hose.

If there is a problem with thepipe, do not repair it yourself.Contact the local After SalesService Provider. Refer to theGuarantee chapter.

The connection must be installed correctlyand fixed into the hob connection pipe.Otherwise, gas may leak from theconnection pipe.

This appliance is supplied for usewith Natural Gas. However, itcan be converted for use withLPG using the installation kitincluded.

Make sure that the gas supplypressure obeys therecommended values. The nut atthe end of the shaft connects tothe R 1/2" parallel thread on theelbow union. The connection issealed using the supplied sealingwasher.

A B C

A. End of shaft with nutB. Washer supplied with the applianceC. Elbow supplied with the appliance

Warning! When you finish theinstallation, check the sealingand pipe fixing. To check theinstallation, use soapy water. Donot use the flame.

Supply pipe sizingThe total hourly gas consumption for theappliance is shown on the data label. Therequired supply pressure (i.e. at inlet toappliance regulator) for each gas type isshown on the data label, refer to the

ENGLISH 18

Technical data chapter. Use this informationin conjunction with the length of run, numberof elbows, tees and bends, the availableservice pressure and the supplyrequirements of other installed appliancesto determine a suitable pipe size. Forassistance in this matter refer to theappropriate section of AS/NZS 5601.1 orAS/NZS 5601.2.An AGA certified class B or D flexibleconnection can be used to connect thecooktop in accordance with AS/NZS5601.1, in particular section 5.9 and clause6.10.1.8, or AS/NZS 5601.2, in particularsection 2.11. Where a hose assembly isused and the cooktop is in the installedposition, the hose assembly shall besuitable for connection to a fixed consumerpiping outlet located at a point 800 –850mm above the floor and in the regionoutside the width of the appliance to adistance of 250mm. The point of connectionto consumer piping must be accessible withappliance installed.Be careful the hose does not come in touchwith mobile parts or is not squeezed. Alsobe careful when the hob is put together withan oven. Ensure that the hose assembly isrestrained from accidental contact with theflue outlet of an underbench oven or anyother hot surface of an adjacent appliance.

RegulatorThe regulator must be positioned that thepressure test nipple is accessible when theappliance is installed. Connect the gassupply to the ½ B.S.P. internal thread inletof the regulator.

A

B

A. OutletB. InletAssembly of regulatorTo connect the regulator to the cooktop usethe elbow and washer supplied with theappliance.The ½" parallel thread connects to the endof shaft with nut. The washer is placedbetween the end of shaft and the elbow.The ½" tapered thread connects to theoutlet of the regulator, and is sealed on thethread. Use thread sealing tape or threadsealing compound.The inlet of the regulator is a ½” parallelthread and is connected to consumer pipingor hose assembly.

The regulators are configured foruse with Natural Gas. It is notrequired to adjust the regulatorto obtain correct outlet pressuresetting.

When the inlet and outlet isorientated correctly the arrow onthe base of the regulatorindicates the direction of gasflow.

ENGLISH 19

Checking the gas supplyIt takes additional time to lightthe gas for the first time. Air ispurged from the pipes.

1. Check if the manometer zero point iscorrect.

2. Connect the manometer to the cooktoppressure point. It is located on theregulator.

3. Turn on the gas supply and electricity,and try to ignite the gas.

4. While the appliance operates check thetest point pressure:

• when all burners of the applianceoperate at maximum,

• when the smallest burner of theappliance operates at minimum.

The outlet pressure should notvary from the nominal outletpressure of 1.00kPa by morethan +/–0.20kPa.

Checking the regulatorIf the regulator works incorrectly:• Adjust of upstream regulator if the outlet

and inlet pressure is too low or anupstream regulator or valve withinsufficient flow capacity is present in thegas supply line.Check again the inlet and test pointpressure, the inlet pressure needs to be1.13 - 5kPa.

• Check if the inlet and outlet is orientatedcorrectly the arrow on the base of theregulator indicates the direction of gasflow.

If the regulator still does not workcorrectly contact the After SalesService Provider.

Warning! Check if the hoseassembly is restrained fromaccidental contact with the flueoutlet of an oven or any otherhot surface of an adjacentappliance.

Gas setting conversion

You can check the parameters ofadjustment setting for thisappliance on the rating plate.Refer to the Technical datachapter.

You can use this model withnatural gas. However, you canconvert it for use with othergases, providing the correctinjectors.

For more information on injectorreplacement, refer to the Technical datachapter.

Warning! Conversion orreplacement can only beperformed by a authorisedtechnician.

To replace injectors:1. Remove pan support.2. Remove burner cap and crown.3. Using a socket spanner 7, unscrew and

remove the injectors, and replace themwith the ones required for the type ofgas in use.

4. Reassemble the parts, following thesame procedure backwards.

5. Unscrew the top hat nut from theregulator (B). The top hat nut andcontrol pressure spring assembly isdisengage as an assembly.

6. Unscrew the threaded pin from top hat(C).

7. Upturn threaded pin, spring is free andscrew pin back into the top hat until firm(E).

8. Refit the top hat nut assembly to theregulator (G), check that it is fullyscrewed down. The regulator is now setfor connection to LPG (H).

ENGLISH 20

9. Turn on the gas supply. Use soapywater to check for leaks. Each hotplatevalve should be turned on, one at atime, and the injector hole blanked offfor several seconds.

10. The operation of the regulator can beconfirmed by connecting a manometerto the pressure test point located on theside of the regulator body adjacent tothe outlet.

A

B

D

C

top hat nut assemblyfully screwed down

turn top hat nut

anticlockwiseand remove

configuration fornatural gas

HG

F

E

configurationfor LPG

While the appliance operates check theoutlet pressure:• when all burners of the appliance

operate at maximum,• when the smallest burner of the

appliance operates at minimum.

The outlet pressure should notvary from the nominal outletpressure of 2.60kPa by morethan +/–0.52kPa.

If the regulator works incorrectly:• Check again the inlet and outlet

pressure, the inlet pressure must be 2.75- 7kPa.

• Check if the insert is fitted correctly.• Check if the turret screw is fully screwed

down.• Check if the inlet and outlet is orientated

correctly the arrow on the base of theregulator indicates the direction of gasflow.

If the regulator still does not workcorrectly contact the After SalesService.

Place the label with relevantinformation for new type of gasclose to the supply pipe beforesealing the appliance. If theappliance is already sealedplease stick it directly on the usermanual booklet, after Technicaldata chapter, and close to therating plate drawing.

You can find this label inpackage supplied withappliance.

ENGLISH 21

If the feeding gas pressure isdifferent or variable from therequired one, you must install anappropriate pressure adjuster,which is not supplied with theproduct. If needed, it must beordered separately from thelocal After Sales Service Provider,refer to the Guarantee chapter.The pressure adjuster must befitted on gas supply pipe, incompliance with AS/NZS5601:2013.

The rating plate is located below thesurface of the casing.

Adjusting flame levelWhen you install the hob, it is necessary tocheck the minimum flame setting:1. Turn the gas tap to the maximum

position and ignite.2. Set the gas tap to the minimum flame

position and turn the control knob fromminimum to maximum several times. Ifthe flame is unstable or extinguished,follow the procedure further.

3. Re-ignite the burner and set tominimum.

4. Remove the control knob and thegasket.

5. To adjust, use a thin bladed screwdriverand turn the adjustment screw until theflame is steady and does not extinguish.When the knob is turned from minimumto maximum, and vice versa (seefollowing picture).

6. Repeat this procedure for all burners.

ENGLISH 22

7. Reassemble the gasket and the knobs. Warning! If the appliance isconnected to LPG/U-LPG, theregulation screw must befastened as tightly as possible.

If the gasket is damaged, it mustbe ordered from the After SalesService Provider.

Environmental concerns

Recycle materials with the symbol . Putthe packaging in relevant containers torecycle it. Help protect the environment andhuman health by recycling waste ofelectrical and electronic appliances. Do not

dispose of appliances marked with thesymbol with the household waste. Returnthe product to your local recycling facility orcontact your municipal office.

IKEA guarantee

How long is the IKEA guarantee valid?This guarantee is valid for 5 years from theoriginal date of purchase of Your applianceat IKEA Pty Ltd, ABN 84006270757 or atCebas Pty Ltd, ABN 15 009 156 003 (BothTrading as IKEA). The original sales receiptis required as proof of purchase. If servicework is carried out under guarantee, thiswill not extend the guarantee period for theappliance.Who will execute the service?IKEA service provider will provide the serv-ice through its own service operations orauthorized service partner network. ContactIKEA for further information.

If you encounter any trouble with theappliance and wish to register a service callor make a claim, please refer to www.ikea.com.au for your local store aftersales customer service center phonenumber, online email and opening times.The principal address and contact details inAustralia are:For Queensland, New South Wales, andVictorian customers please contact:

IKEA Pty Ltd

ENGLISH 23

IKEA Pty LtdIKEA Service OfficeL1 Clock Tower, 630 Princes HighwayTempe, NSW 2044

Contact - IKEA Customer Service atwww.IKEA.com.au

For Western Australian and SouthAustralian customers please contact:

Cebas Pty Ltd

8c Sunray Drive, Innaloo WA 6018Australia

Contact - IKEA Customer Service atwww.IKEA.com.au

What does this guarantee cover?The guarantee covers faults of the appli-ance, which have been caused by faultyconstruction or material faults from the dateof purchase from IKEA. This guarantee ap-plies to domestic use only. The productshave been designed and tested fordomestic purposes only and this guaranteedoes not cover damage arising from use ofthe Product in a commercial environment.The exceptions are specified under theheadline "What is not covered under thisguarantee?" Within the guarantee period,the costs to remedy the fault e.g. repairs,parts, labour and travel will be covered,provided that the appliance is accessiblefor repair without special expenditure.Replaced parts become the property ofIKEA.The guarantee exists only if the appliancecomplies and is installed in accordancewith:• The technical specifications.• The Assembly Instructions and user

manual Safety Information.

IKEA's guarantee is subject to AustralianConsumer Law - see Schedule 2 toCompetition and Consumer Act, 2010. Thisguarantee is in addition to (and does notexclude, restrict or modify in any way) anynon-excludable statutory warranties inAustralia.What will IKEA do to correct the problem?IKEA appointed service provider will exam-ine the product and decide, at its sole dis-cretion, if it is covered under this guarantee.They will notify you as to whether yourclaim is covered under this guarantee. Ifyour claim is approved, the IKEA serviceprovider or its authorized service partner,will then, at its sole discretion, either repairthe defective product or replace it with thesame or a comparable product.What is not covered under thisguarantee?• Normal wear and tear.• Deliberate or negligent damage, dam-

age caused by failure to observe operat-ing instructions, incorrect installation orby connection to the wrong voltage, dam-age caused by chemical or electro-chem-ical reaction, rust, corrosion or waterdamage including but not limited to dam-age caused by excessive lime in the wa-ter supply, damage caused by abnormalenvironmental conditions.

• Consumable parts including batteriesand lamps.

• Non-functional and decorative partswhich do not affect normal use of the ap-pliance, including any scratches and pos-sible colour differences.

• Accidental damage caused by foreignobjects including insect or vermininfestation or substances and cleaning orunblocking of filters, drainage systems orsoap drawers.

• Damage to the following parts: ceramicglass, accessories, crockery and cutlerybaskets, feed and drainage pipes, seals,

ENGLISH 24

lamps and lamp covers, screens, knobs,casings and parts of casings. Unless suchdamages can be proved to have beencaused by production faults.

• Cases where no fault could be found dur-ing a technician's visit.

• Repairs not carried out by our appointedservice providers and/or an authorizedservice contractual partner or wherenon-original parts have been used.

• Repairs caused by installation which isfaulty or not according to specification.

• The use of the appliance in a non-domes-tic environment i.e. professional use.

• Transportation damages. If a customertransports the product to their home orother address, IKEA is not liable for anydamage that may occur during transport.However, if IKEA delivers the product tothe customer's delivery address, thendamage to the product that occursduring this delivery will be covered bythis guarantee.

• Cost for carrying out the initialinstallation of the IKEA appliance.However, if an IKEA service provider orits authorized service partner repairs orreplaces the appliance under the termsof this guarantee, the service provider orits authorized service partner will re-install the repaired appliance or installthe replacement, if necessary.

• The appliance's serial number orwarranty seal has been removed ordefaced.

How country law appliesOur goods come with guarantees thatcannot be excluded under the AustralianConsumer Law (ACL). You are entitled to areplacement or refund for a major failureand compensation for any other reasonablyforeseeable loss or damage.You are also entitled to have the goodsrepaired or replaced if the goods fail to beof acceptable quality and the failure doesnot amount to a major failure.

This guarantee is not intended in any wayto limit or exclude such rights and remediesthat you may have under law.You can find out more information aboutthe Australian Consumer Law on the ACCCwebsite: www.accc.gov.auArea of validityThis IKEA guarantee applies only toproducts purchased and installed inAUSTRALIA .What you must do to make a claim underthe guarantee:To make a claim under the guaranteecontact IKEA after sales customer servicecenter at the above address, the IKEAcatalogue or refer to www.ikea.com.au foryour local store customer service phonenumber, online email and opening times.Please describe the problem that you arefacing with the appliance in detail alongwith your product article number (8 digitcode) and date of purchase at the time ofcall registration.Please do not hesitate to contact thededicated after sales customer servicecenter for IKEA appliances to:1. Make a service request under this guar-

antee;2. Ask for clarification on installation of the

IKEA appliance in the dedicated IKEAkitchen furniture.

3. Ask for clarification on user manual con-tents and specifications of the IKEA ap-pliance.

To ensure that we provide you with the bestassistance, please read carefully the As-sembly Instructions and/or the User Manualsection of this booklet before contacting us.How to reach us if you need our service

ENGLISH 25

The IKEA after sales customer service centrewill assist you on the phone with basictrouble shooting for your appliance at thetime of service call request. Please refer tothe IKEA catalogue or www.ikea.com.auand select your local store for local storephone numbers and opening times.

Please describe the problem thatyou are facing with theappliance in detail alongwith your product article number( 8 digit code ) and date ofpurchase at the time of callregistration .

SAVE THE SALES RECEIPT!Kindly keep all these details andoriginal invoice of purchasehandy during the servicetechnician's visit to enable him tocarry out the job.It is your proof of purchase andrequired for the guarantee toapply. Note that the receiptreports also the IKEA articlename and number (8 digit code)for each of the appliances youhave purchased.

ENGLISH 26

*

ENGLISH 27

matmÄssig au - ikea€¦ · children and vulnerable people safety ... • warning: unattended...

Documents