manufacturing, inc. · great plains manufacturing wants you to be satisﬁed with any new machine...

! Read this manual entirely. When you see this symbol, the subsequent instructions andwarnings are serious - follow without exception. Your life and the lives of others dependon it!

Cover illustration may show optional equipment not supplied with standard unit.

© Copyright 2003 Printed

P.O. Box 5060 ● Salina, Kansas 67402-5060Manufacturing, Inc.

PURPLE

148-693Q

17206

7/16/2003

Predelivery InstructionsFCP1000

Three-Meter Drill and Hitch

Table of Contents

Great Plains Mfg., Inc.

Table of Contents

Important Safety Information . . . . . . . . . . . . . . . . . 1

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Description of Unit . . . . . . . . . . . . . . . . . . . . . . . . 2

Intended Usage . . . . . . . . . . . . . . . . . . . . . . . 2

Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . 2

Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Assembly and Setup Assistance . . . . . . . . . . . . . 2

Section 1 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 3

Pre-Assembly Checklist . . . . . . . . . . . . . . . . . . . . 3

Section 2 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Prestart Checklist. . . . . . . . . . . . . . . . . . . . . . . . . 4

Hitching Tractor to Implement . . . . . . . . . . . . . . . 4

Hydraulic Hook-up . . . . . . . . . . . . . . . . . . . . . . . . 5

Bleeding Hydraulic Systems . . . . . . . . . . . . . . . . 5

© Copyright 2003 All rights Reserved

Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kiof this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omtion contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and imtime of its publication, and may not reflect the product in the future.

Great Plains ManufacturingThe following are trademarks of Great Plains Mfg., Inc.: A

All other brands and product names are trademarks

Printed in the United

FCP1000 Three-Meter Drill and Hitch 148-693Q

Bleeding Tongue Cylinder. . . . . . . . . . . . . . . . 5

Bleeding Transport Lift Cylinders . . . . . . . . . . 5

Bleeding Marker Hydraulics . . . . . . . . . . . . . . 6

Contact Drive Assembly . . . . . . . . . . . . . . . . . . . . 8

Box and Divider Assembly . . . . . . . . . . . . . . . . . 10

Box to Frame Assembly . . . . . . . . . . . . . . . . . . . 12

Walkboard Assembly . . . . . . . . . . . . . . . . . . . . . 14

Lights and Handles Assembly. . . . . . . . . . . . . . . 16

Decal Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 18

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Torque Values Chart for Common Bolt Sizes . . . 20

Tire Inflation Chart . . . . . . . . . . . . . . . . . . . . 20

nd, either expressed or implied. While every precaution has been taken in the preparationissions. Neither is any liability assumed for damages resulting from the use of the informa-prove its products as it sees fit. This publication describes the state of this product at the

, Incorporated Trademarkspplication Systems, Ausherman, Land Pride, Great Plains

or registered trademarks of their respective holders.

States of America.

11/4/08

1

Important Safety Information

11/4/08 FCP1000 Three-Meter Drill and Hitch 148-693Q


Important Safety Information

For your safety, thoroughly read “Important Safety Informa-tion” and “Operating Instructions” in the operator’s manualbefore proceeding.

Safety NotationsThe SAFETY ALERT SYMBOL indicates that there is a poten-tial hazard to personal safety involved and extra safety precau-tions must be taken. When you see this symbol, be alert andcarefully read the message that follows it. In addition to designand configuration of equipment, hazard control and accidentprevention are dependent upon the awareness, concern, pru-dence and proper training of personnel involved in the opera-tion, transport, maintenance and storage of equipment.

Watch for the following safety notations throughout this manu-al.

! DANGER!Indicates an imminently hazardous situation which, if notavoided, will result in death or serious injury. This signal wordis limited to the most extreme situations.

! WARNING!Indicates a potentially hazardous situation which, if not avoid-ed, could result in death or serious injury.

! CAUTION!Indicates a potentially hazardous situation which, if not avoid-ed, may result in minor or moderate injury. It may also be usedto alert against unsafe practices.

Safety RulesMost accidents are the result of negligence, carelessness orfailure to follow safety precautions. Though your implement isdesigned with many built-in safety features, safety precautionsare mandatory to prevent accidents.

!

Introduction


Introduction

Great Plains Manufacturing wants you to be satisfied withany new machine delivered by the Great Plains Truckingnetwork. To ease the assembly task and produce a prop-erly working machine, read this entire manual before as-sembling or setting up new equipment.

Description of UnitThe CP1000 is a pull-type seeding implement. The imple-ment consists of a three-point drill mounted on a centre-pivot hitch. The hitch and drill are integrally connected.No-till coulters are mounted on the hitch to zone-till stripsfor seed furrows. Straight-arm openers on the drill prepareseedbeds and place the seed. The pivoting action of thehitch helps drill openers track the coulters. A contract-drive tire on the drill powers seeding off a hitch tire. Thetongue cylinder controls coulter depth and transport cylin-ders raise the drill for turns and transport.

Intended UsageUse this implement for seeding production-agriculturecrops only. Do not modify implement for use with attach-ments other than those specified by Great Plains. Useimplement in no or minimum tillage.

Using This ManualThis manual was written to help you assemble and pre-pare the new machine for the customer. The manual in-cludes instructions for assembly and setup. Read thismanual and follow the recommendations for safe, efficientand proper assembly and setup.

An operator’s manual is also provided with the new ma-chine. Read and understand “Important Safety Informa-tion” and “Operating Instructions” in the operator’smanual before assembling the machine. As a reference,keep the operator’s manual on hand while assembling.

The information in this manual is current at printing. Someparts may change to assure top performance.

2 FCP1000 Three-Meter Drill and Hitch 148-693Q

DefinitionsThe following terms are used throughout this manual.

Right and left as used in this manual are determined byfacing the direction the machine will travel while in use un-less otherwise stated.

NOTE: Useful information about the preceding topic.

Assembly and Setup AssistanceTo order additional copies of predelivery instructions oroperator’s and parts manuals, write to the following ad-dress. Include model numbers in all correspondence.

If you do not understand any part of this manual or haveother assembly or setup questions, assistance is avail-able. Contact

Product SupportGreat Plains Mfg. Inc., Service Department

P.O. Box 5060Salina, KS 67402-5060

IMPORTANT: A crucial point of information about thepreceding topic. For safe and correct operation, readand follow the directions provided before continuing.

11/4/08

3

Section 1 Assembly



Section 1 Assembly

The following headings are step-by-step instructions forassembling the CP1000. Begin Pre-Assembly Checklist tomake sure you have all necessary parts and equipment.Then proceed with assembly as shown on the attachedhandouts.

Pre-Assembly Checklist1. Read and understand “Important Safety Informa-

tion” on page 1 before assembling.

2. Have at least two people on hand while assembling.

3. Make sure the assembly area is level and free of ob-structions (preferably an open concrete area).

4. Have all major components.

5. Have all fasteners and pins shipped with the drill.

6. Have a copy of the parts manual on hand. If unsure ofproper placement or use of any part or fastener, referto the parts manual.

7. Check that all working parts are moving freely, boltsare tight, and cotter pins are spread.

8. Check for proper tension and alignment on all drivechains.

9. Check that all safety labels and reflectors are correctlylocated and legible. Replace if improperly located ordamaged. Refer to Safety Labels, “Important SafetyInformation” in the operator’s manual.

10. Inflate tires to recommended pressure as listed on theTire Inflation Chart on the “Appendix” on page 20.Tighten wheel bolts as specified on Torque ValuesChart on the “Appendix” on page 20.

IMPORTANT: If a pre-assembled part or fastener istemporarily removed, remember where it goes. Keepthe parts separated.

4

Section 2 Setup

FCP1000 Three-Meter Drill and Hitch 148-693Q 11/4/08


Section 2 Setup

This section will help you prepare your tractor and imple-ment for use.

Prestart Checklist1. Read and understand “Important Safety Informa-

tion,” page 1.

2. Check that all working parts are moving freely, boltsare tight, and cotter pins are spread.

3. Check that all safety decals and reflectors are cor-rectly located and legible. Replace if damaged. SeeSafety Decals, “Important Safety Information,”in the operator’s manual.

4. Inflate tires to pressure recommended and tightenwheel bolts as specified. See “Appendix,” page 20.

Hitching Tractor to Implement

! DANGER!You may be severely injured or killed by being crushed betweenthe tractor and drill. Do not stand or place any part of yourbody between drill and moving tractor. Stop tractor engine andset park brake before installing pins.

Refer to Figure 11. Place hitch weldment (1) over ball swivel on hitch

tongue (2). Hold hitch weldment in place by insertingspacer tube (3) through hitch clevis and ball swivel.

2. Back tractor up to hitch and bolt hitch weldment totractor drawbar using 1” x 10” bolt (4), large flatwasher (5), lock washer (6) and nut (7).

3. Use 3/4” x 9” bolt (8) to bolt hitch weldment through itsslotted hole and onto secondary hole of tractor draw-bar. Install a 3/4” flat washer (9) next to top slotted holeand fasten with a lock washer (10) and nut (11).Tighten both bolts.

Figure 1Drawbar Assembly Illustration

4. Securely attach safety chain to tractor-drawbar frame.

Refer to Figure 25. Remove jack from stob on side of hitch tongue and

place in transport position on implement.

Figure 2Jack in Transport Position

17219


Hydraulic Hook-up

! WARNING!Escaping fluid under pressure can have sufficient force to pene-trate the skin. Check all hydraulic lines and hoses before apply-ing pressure. Fluid escaping from a very small hole can bealmost invisible. Use paper or cardboard, not body parts, tocheck for suspected leaks. If injured, seek medical assistancefrom a doctor that is familiar with this kind of injury. Foreignfluids in the tissue must be surgically removed within a fewhours or gangrene will result.

Refer to Figure 6Great Plains hydraulic hoses are colour coded to help youhook-up hoses to your tractor outlets. Hoses that go to thesame remote valve are marked with the same colour. To

distinguish hoses on the same hydraulic circuit, refer toplastic hose holder. Connect hose under extended cylin-der to outlet you choose for cylinder extension. Connecthose under retracted symbol to outlet for cylinder retrac-tion.

Figure 6Hydraulic Hose Color Ties

Connect hydraulic hoses from tongue cylinder to one trac-tor remote valve. Connect hoses from transport-lift cylin-ders to another tractor remote valve.

Colour Hydraulic Function

Red Transport Lift Cylinders

Blue Tongue Cylinder

17641

11/4/08

Bleeding Hydraulic SystemsFor safe and smooth operation, the hydraulic systemsmust be free of air. Bled the hydraulic systems during ini-tial implement set-up.

Bleeding Tongue Cylinder1. Check hydraulic fluid in tractor reservoir and fill to

proper level. Add fluid to system as needed. Tonguecylinder capacity is 1.89 litres (one-half gallon).

2. Raise and safely support hitch, transport frame andfront tongue.

3. Unpin rod end of tongue cylinder. Block, wire or other-wise safely support cylinder so when rod end is fullyextended it does not contact anything.

4. Cycle cylinder completely in and out at least threetimes to purge air from cylinder and hoses.

5. Fully extend cylinder and repin rod end.

6. Re-check tractor reservoir and fill to proper level.

Bleeding Transport Lift CylindersThe transport-lift cylinders are rephasing cylinders and re-quire a special procedure for bleeding air from the circuit.Read and follow procedure carefully. Cylinders will notfunction properly with air in the hydraulic circuit.

1. Check hydraulic fluid in tractor reservoir and fill toproper level. Add fluid to system as needed. Trans-port-lift-cylinder capacity is about 7.57 litres (2 gal-lons).

2. Jack up and support hitch frame.

Refer to Figure 73. Remove 1/2” nylock nuts (1) on spring side of cylinder-

support brace. Unpin cylinders. Do not alter position ofjam nuts (2) on centre of support-brace bolts.

Figure 7Unpin Cylinders

17864

5FCP1000 Three-Meter Drill and Hitch 148-693Q


4. Turn cylinders to a position where rod ends are higherthan base ends. Support cylinders in a safe location.

5. Start tractor and run engine at idle speed. With rodends higher than base ends, hydraulically extend cyl-inders. After cylinder rods are fully extended, continueto hold control lever for one minute before hydrauli-cally retracting cylinders.

6. Repeat step 5 three times to completely bleed system.If air is still trapped in either cylinder, it will operate injerky, erratic motions. Repeat steps until cylindermovement is smooth and even.

7. Repin cylinders to hitch frame. Reinstall short com-pression springs on cylinder-support-brace bolts andre-tighten 1/2” nylock nuts until springs are com-

8. pressed to 32 mm (1 1/4”). If for any reason the 1/2”jam nuts in centre of support-brace bolts werechanged, refer to Transport Cylinder Support Brace inthe operator’s manual for proper adjustment.

9. Refill tractor hydraulic-fluid reservoir to proper level.

Bleeding Marker Hydraulics

! CAUTION!You may be injured if hit by a folding or unfolding marker.Markers may fall quickly and unexpectedly if the hydraulics fail.Never allow anyone near the drill when folding or unfolding themarkers.

1. Check that tractor hydraulic reservoir is full.

2. With both markers lowered into field position, loosenhydraulic-hose fittings at rod and base ends of markercylinders. Loosen fittings on back side of sequencevalve.

3. With tractor idling, activate tractor hydraulic valve untiloil seeps out around a loosened fitting. Tighten that fit-ting.

4. Reactivate tractor hydraulic valve until oil seeps outaround another loosened fitting. Tighten that fitting.Repeat process until all loosened fittings have beenbled and tightened.

Refer to Figure 35. With center-pivot hitch properly secured to tractor

drawbar, remove transport lock pins located in verticaltubes above tires and place in storage hole next to sta-bilizer cylinder on hitch as shown.

Figure 3Transport Pins in Storage

6. Position the center pivot hitch in front of drill. Use thetransport-lift cylinders to vertically align the mainframe clamp plates with the drill box frame.

Refer to Figure 47. Center the main frame clamp plates with the box

frame. Attach the box frame to the main frame clampplates with two 3/4” x 6” x 5 5/8” U-bolts, 3/4” flat wash-ers, 3/4” lock washers and 3/4” nuts.

Figure 4Attaching Frames

IMPORTANT: Never bleed an O-ring fitting. Instead,bleed a nearby pipe or JIC fitting.

IMPORTANT: JIC fittings do not require high torque.JIC and O-ring fittings do not require sealant. Alwaysuse liquid pipe sealant when adding or replacing pipe-thread fittings. To avoid cracking hydraulic fittings fromover tightening, do not use plastic sealant tape.

12081

21616

Box FrameMain FrameClamp Plate

U-Bolt

6 FCP1000 Three-Meter Drill and Hitch 148-693Q 11/4/08


Refer to Figure 58. Remove the tierod weldment from the contact drive

assembly. Position the contact drive assembly aroundthe transport lift and reattach the tierod weldment tothe contact drive assembly.

Figure 5Contact Drive Assembly

Note: For the assistance with the remainder of drill as-sembly use the drawings and part descriptions on the fol-lowing pages.

21617

TransportLift

Tierod Contact DriveAssembly

11/4/08
7FCP1000 Three-Meter Drill and Hitch 148-693Q



Contact Drive Assembly

20477



1. 805-180C PIN ROLL 1/4 X 1 1/2 LG PLT2. 148-675H CP1000 CONT WHL WLMT3. 148-518H NTA1300 CON WHL TIEROD WLMT4. 248-263D CP1000 CONTACT WHL AXLE SHAFT5. 402-038H BRACE WELD, GUAGE WHEEL6. 148-676H CP1000 CONT DR SHLD HOUS WLMT7. 148-674H CP1000 CONT WHL DRIVE ARM WLMT8. 402-126H OFFSET DOUBLE IDLER WELDMENT9. 402-242D IDLER BOLT PLATE10. 402-268D OFFSET DRIVE WHEEL COLLAR11. 802-017C HHCS 3/8-16X1 GR512. 802-155C RHSNB 3/8-16X1 1/4 GR513. 802-568C HFSS 1/2-13X1 GR514. 803-201C NUT HEX COUPLER 3/8-16 X 1 3/415. 803-209C NUT FLANGE LOCK 3/8-16 PLT16. 803-215C NUT NYLOCK JAM THIN 3/8-16 PLT17. 804-013C WASHER LOCK SPRING 3/8 PLT18. 805-064C PIN COTTER 7/64 X 1 LONG19. 814-134C TIRE/WHEEL ASSY 13/5 X 620. 148-677H CP1000 CONT DR SHLD WLMT21. 120-305D TUBE RND 1 OD X 7/32W X 1.5622. 804-061C WASHER MACH 1.50 X 1.00 X 18GA23. 188-006V BEARING .880 HEX BORE 205DD24. 804-017C WASHER FLAT 1/2 USS PLT25. 817-406C IDLER 1 PC 2.38X1.01X1.06226. 817-229C PLASTIC SLEEVE27. 838-363C DECAL PIC--MOVING CHAIN28. 802-569C HFSS 3/8-16X1 1/2 GR529. 838-261C DECAL CP1000 CALIBRATION30. 802-079C HHCS 3/8-16X1 1/4 GR531. 804-012C WASHER FLAT 3/8 SAE PLT32. 802-078C HHCS 1/4-20X5/8 GR533. 804-007C WASHER FLAT 1/4 SAE PLT34. 817-341C DRIVE MODULE TOP COVER35. 800-163C CLIP U-TYPE NUT 1/4-20 SLF-RET36. 148-571D MID SHAFT37. 808-219C SPKT 40C12 X 7/8 HEX BORE38. 136-090D CHAIN RL #40 132 PITCHES39. 121-763S OPENER SPRING ROD ASSY. SHRT.40. 816-306C PLUG, SPRING ROD CASTING41. 802-550C HHCS 1/2-13X10 SPTHD GR842. 812-236C OPNR SPRING RD TRUNION CASTING43. 807-159C SPRING COMP 2 1/2ODX3/8X12 7/844. 121-154D SPRING STOP STAMPING45. 803-193C NUT HEX FLANGE 1/2-13 GR G PLT46. 803-036C NUT HEX JAM 1/2-13 PLT47. 121-166D ADJ. YOKE END48. 805-127C PIN CLEVIS 1/2 X 1 3/449. 805-109C PIN COTTER 1/8 X 1 1/4 PLT50. 806-044C U-BOLT 5/8-11 X 5 1/32 X 6 GR551. 148-519H NTA1300 CON WHL SPRING MNT52. 804-021C WASHER FLAT 5/8 SAE PLT53. 804-022C WASHER LOCK SPRING 5/8 PLT54. 803-021C NUT HEX 5/8-11 PLT55. 805-234C PIN CLEVIS 1/2 X 4 PLATED56. 402-140S DOUBLE SPOOL IDLER ASSY57. 805-093C PIN COTTERLESS HITCH 1/4 X 2 P58. 148-413H CALIBRATION HANDLE WELDMENT59. 136-036D CHAIN RL #40 70 PITCHES60. 136-104D CHAIN RL #40 62 PITCHES61. 809-070C CHAIN CONNECTOR LINK #40 OFFST62. 808-147C SPKT 40C15 X 7/8 HEX BORE

Contact Drive Assembly



Box and Divider Assembly

21597



1. 195-292H CP1000 FIN BOX FRONT PNL WLMT2. 195-294H CP1000 FIN BOX RH SIDE PNL3. 195-305D CP1000 FIN BOX UPPER REAR PNL4. 195-293H CP1000 FIN BOX LH SIDE PNL5. 195-318D CP1000 FIN BOX LIGHT BRACKET6. 195-290H CP1000 FIN BOX BASE WLMT7. 195-308D CP1000 FIN BOX FRONT BRACE8. 195-291H CP1000 FIN BOX FERT DOOR WLMT9. 195-315D CP1000 FIN BOX COVER SUPPORT10. 195-310D CP1000 FERT GATE SEAL CLMP PLT11. 816-427C CP1000 FIN FERT DOOR SEAL BTM12. 816-428C CP1000 FIN FERT DOOR SEAL SIDE13. 803-088C NUT HEX LOCK 1/4-20 FLG14. 802-089C RHSNB 1/4-20X3/4 SS15. 800-352C DESTACO 602 STRAIGHT-LINE CLMP16. 802-568C HFSS 1/2-13X1 GR517. 803-037C NUT HEX WHIZ 1/2-13 PLT18. 803-198C NUT HEX WHIZ 3/8-16 PLT19. 802-185C HFSS 3/8-16X3/4 LG20. 806-062C U-BOLT 5/8-11 X 4 1/32 X 5 3/421. 195-286D CP1000 FIN BOX HINGE PVT PIN22. 802-370C HHCS 1/4-20X1 3/4 GR523. 803-007C NUT LOCK 1/4-20 PLT24. 803-021C NUT HEX 5/8-11 PLT25. 804-022C WASHER LOCK SPRING 5/8 PLT26. 804-019C WASHER FLAT 5/8 USS PLT27. 195-317D CP1000 FIN BOX GATE KEEPER-BTM28. 195-316D CP1000 FIN BOX GATE KEEPER-TOP29. 802-214C RHSNB 1/2-13X1 1/4 GR5

Box and Divider Assembly



Box to Frame Assembly

20486



1. 148-690H CP1000 SUB FRAME WLMT2. 802-091C HHCS 1/2-13X1 1/2 GR53. 804-016C WASHER FLAT 1/2 SAE PLT4. 804-015C WASHER LOCK SPRING 1/2 PLT5. 803-020C NUT HEX 1/2-13 PLT6. 248-262D CP1000 FRAME MOUNTING BAR7. 804-024C WASHER FLAT 3/4 USS PLT8. 802-212C HHCS 3/4-10X2 1/2 GR59. 804-023C WASHER LOCK SPRING 3/4 PLT10. 803-027C NUT HEX 3/4-10 PLT11. 806-128C U-BOLT 3/4-10 X 6 1/32 X 5 5/812. 806-062C U-BOLT 5/8-11 X 4 1/32 X 5 3/413. 804-019C WASHER FLAT 5/8 USS PLT14. 804-022C WASHER LOCK SPRING 5/8 PLT15. 803-021C NUT HEX 5/8-11 PLT

Box to Frame Assembly



Walkboard Assembly

20488



1. 802-091C HHCS 1/2-13X1 1/2 GR52. 804-016C WASHER FLAT 1/2 SAE PLT3. 802-034C HHCS 1/2-13X1 1/4 GR54. 804-015C WASHER LOCK SPRING 1/2 PLT5. 803-020C NUT HEX 1/2-13 PLT6. 119-192D STEP7. 148-319H WALKBOARD WELDMENT8. 801-018C SCREW RD HD 1/4-20 X 5/89. 838-369C DECAL 25KM PER HR10. 148-962D NTA1300 KM-HR BACKING PLT11. 804-007C WASHER FLAT 1/4 SAE PLT12. 804-006C WASHER LOCK SPRING 1/4 PLT13. 803-006C NUT HEX 1/4-20 PLT

Walkboard Assembly



Lights and Handles Assembly

20489



1. 803-169C NUT HEX FLG. LOCK 1/2-13 PLT.2. 801-151C SCR HEX SELF TAP 1/4-20X1TYPEF3. 150-138D 12’ EWNT LIGHT BRACKET (S/N RR1168-)4. 890-312C DUAL AG LIGHTS RH5. 802-203C HFSS 1/2-13X1 1/2 GR56. 119-190D HANDLE7. 800-082C CABLE TIE .31X21.5 6DIA 120LB8. 890-390C LIGHT HARNESS, 10’ WISHBONE9. 890-391C LIGHT HARNESS, 15’ LEAD10. 804-017C WASHER FLAT 1/2 USS PLT11. 195-318D CP1000 FIN BOX LIGHT BRACKET (S/N RR1169+)12. 802-568C HFSS 1/2-13X1 GR513. 803-037C NUT HEX WHIZ 1/2-13 PLT14. 248-251D MANUAL PAK MOUNTING PLATE15. 802-004C HHCS 1/4-20X3/4 GR516. 817-042C MINI END WHEEL PRESS WHEEL17. 803-293C NUT HEX FLANGE LOCK 1/4-20 PLT18. 817-516C MANUAL PAK 1" W/ GASKET19. 890-311C DUAL AG LIGHTS LH

Lights and Handles Assembly



Decal Assembly

20495



Decal Assembly

1. 818-019C DECAL WARNING NEG TONGUE WT2. 818-016C DECAL CAUTION PIVOT PULL HITCH3. 818-181C DECAL STROKE GAUGE4. 838-161C DECAL LOGO&GP F/STRIPE 4 X 245. 838-265C DECAL REFLECTOR AMBER 1 1/2X96. 838-361C DECAL PIC--DO NOT RIDE7. 818-398C DECAL CAUTION TIRES NOT A STEP8. 838-363C DECAL PIC--MOVING CHAIN9. 838-069C DECAL 1000 DRIVE TYPE10. 838-229C DECAL GREAT PLAINS ON LOGO LRG11. 148-693B MANUAL FCP1000 SEED RATE12. 838-369C DECAL 25KM PER HR13. 838-266C DECAL REFLECTOR RED 1 1/2X914. 838-160C DECAL 3 COLOR STRIPE 2.50 WIDE15. 838-214C DECAL CP1000F16. 838-360C DECAL PIC--WEAR EYE PROTECTION

20

Appendix

FCP1000 Three-Meter Drill and Hitch 148-693Q 11/4/08


Appendix

Torque Values Chart for Common Bolt Sizes

in-tpi1 N · m2 ft-lb3 N · m ft-lb N · m ft-lb mm x pitch4 N · m ft-lb N · m ft-lb N · m ft-lb

1/4" - 20 7.4 5.6 11 8 16 12 M 5 X 0.8 4 3 6 5 9 7

1/4" - 28 8.5 6 13 10 18 14 M 6 X 1 7 5 11 8 15 11

5/16 - 18 15 11 24 17 33 25 M 8 X 1.25 17 12 26 19 36 27

5/16" - 24 17 13 26 19 37 27 M 8 X 1 18 13 28 21 39 29

3/8" - 16 27 20 42 31 59 44 M10 X 1.5 33 24 52 39 72 53

3/8" - 24 31 22 47 35 67 49 M10 X 0.75 39 29 61 45 85 62

7/16" - 14 43 32 67 49 95 70 M12 X 1.75 58 42 91 67 125 93

7/16" - 20 49 36 75 55 105 78 M12 X 1.5 60 44 95 70 130 97

1/2" - 13 66 49 105 76 145 105 M12 X 1 90 66 105 77 145 105

1/2" - 20 75 55 115 85 165 120 M14 X 2 92 68 145 105 200 150

9/16" - 12 95 70 150 110 210 155 M14 X 1.5 99 73 155 115 215 160

9/16" - 18 105 79 165 120 235 170 M16 X 2 145 105 225 165 315 230

5/8" - 11 130 97 205 150 285 210 M16 X 1.5 155 115 240 180 335 245

5/8" - 18 150 110 230 170 325 240 M18 X 2.5 195 145 310 230 405 300

3/4" - 10 235 170 360 265 510 375 M18 X 1.5 220 165 350 260 485 355

3/4" - 16 260 190 405 295 570 420 M20 X 2.5 280 205 440 325 610 450

7/8" - 9 225 165 585 430 820 605 M20 X 1.5 310 230 650 480 900 665

7/8" - 14 250 185 640 475 905 670 M24 X 3 480 355 760 560 1050 780

1" - 8 340 250 875 645 1230 910 M24 X 2 525 390 830 610 1150 845

1" - 12 370 275 955 705 1350 995 M30 X 3.5 960 705 1510 1120 2100 1550

1-1/8" - 7 480 355 1080 795 1750 1290 M30 X 2 1060 785 1680 1240 2320 1710

1 1/8" - 12 540 395 1210 890 1960 1440 M36 X 3.5 1730 1270 2650 1950 3660 2700

1 1/4" - 7 680 500 1520 1120 2460 1820 M36 X 2 1880 1380 2960 2190 4100 3220

1 1/4" - 12 750 555 1680 1240 2730 2010

1 3/8" - 6 890 655 1990 1470 3230 2380 1 in-tpi = nominal thread dia.in inches-threads per inch

1 3/8" - 12 1010 745 2270 1670 3680 2710 2 N· m = newton-meters

1 1/2" - 6 1180 870 2640 1950 4290 3160 3 ft-lb= foot pounds

1 1/2" - 12 1330 980 2970 2190 4820 3560 4 mm x pitch = nominal thread dia. in millimeters x thread pitch

Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.

5.8 8.8 10.9

Class 5.8 Class 8.8 Class 10.9

Bolt Head Identification

Bolt Size(Metric)Grade 2 Grade 5 Grade 8

Bolt Head Identification

Bolt Size(Inches)

Tire Inflation ChartTire Size PSI (bar) Tire Size PSI (bar)

Contact Wheel 40 (2.75) 13.0/55-16 12 PR AW 65 (4.48)

Great Plains Manufacturing, Inc.Corporate Office: P.O. Box 5060Salina, Kansas 67402-5060 USA

manufacturing, inc. · great plains manufacturing wants you to be satisﬁed with any new machine...

Documents