manuel hİdrolİk pres - · pdf filemanuel hİdrolİk press makİnesİ manual hydraulic press...
TRANSCRIPT
MANUEL HİDROLİK PRESS MAKİNESİ MANUAL HYDRAULIC PRESS MACHINE
KULLANMA KLAVUZU / USER'S GUIDE GTİP/HS Code: 8462.39.91.00.12
1
Çelik Kuyumculuk Kalıp Makine San. Ve Tic.
Ltd. Şti.
Adres: Atatürk Mahallesi Marmara Sanayi Sitesi R Blok No:
455 İkitelli/Küçükçekmece İstanbul
Telefon: +90 212 494 44 60
Fax: +90 212 494 44 61
Web: www.steelkalip.com
E-mail adresi: [email protected]
2
İÇİNDEKİLER:
. Teknik Özellikler
. Genel Açıklamalar
. Makine Montaj Şeması
. Parça Listesi
. Elektrik Paneli
. Kontrol Paneli
. Makinenin Kullanıma Hazırlanması
. Dikkat Edilmesi Gereken Hususlar
. Makine Bakım ve Onarımı
3
Teknik Özellikler:
En, Boy, Yükseklik : *102 *73 *185
Net Ağırlık : 470 Kg
Kullanılan Elektrik : 380 Volt / 50 HZ
Kullanılan Hava Basıncı : Min. 4 Bar
Motor Gücü : 7.5 Kw
Pres Baskı Adeti : 170 Adet/ Dk
Genel Açıklamalar :
*Preslerimiz CE belgeli ve sertifikalıdır. Ürünlerimiz kullanım hataları hariç 2
yıl garantilidir.
*Kullanım kitapçığında belirtilen özellikte yağ kullanılmalıdır. 37 No Hidrolik
yağı.
*Makinenin strok boyu standart ölçüde 110mm'dir.
4
Makine Montaj Şeması:
Parça Listesi :
1. Yukarı Ayarı
2. Aşağı Ayarı
3. Pres Klavuz Mili
4. Kalıp Bağlama Yeri
5. Basınç Göstergesi
6. Basınç Ayarı
7. Otomatik
8. Alt Tabla
9. Çekmece
5
Elektrik Paneli :
1. Motor Koruma Şalteri
2. W-Otomat
3. Güç Kontaktörü
4. Aşağı Valf Rölesi
5. Yukarı Valf Rölesi
6. Kontaktör Rölesi
7. Aşağı Sensör Rölesi
8. Yukarı Sensör Rölesi
9. Fotosel Rölesi
6
Kontrol Paneli:
1. Hava Anahtarı
2. Pres hareketinin en üst konumunu belirler
3. Pres hareketinin en alt konumunu belirler
4. Pres hareket yönünü ışıkla gösterir
5. Basınç Göstergesi
6. Basınç Ayarlama
7. Otomatik Çalıştırma
7
1. Presin yukarı çıkmasını sağlar.
2. Açma- Kapama ana şalteri
3. Acil stop
4. Presin basma sayısını gösterir
5. Presin aşağı inmesini sağlar.
6. Basınç şalteri
7. Pedal
8. Manuel veya otomatik konuma geçiş şalteri
Makinenin Kullanıma Hazırlanması:
- Makinenin yağ tankına 37 ile 46 numara arasında hidrolik yağ ile göstergeye
göre doldurun.
- Elektrik fişini prize takın. 380 V ve 3 fazlıdır ayrıca makine üzerinde 5 adet
kablo vardır. Bunlar;
sarı toprak, mavi nötr, siyah ve kahverengi ise faz kablolarıdır. Eğer
8
kullanacağınız ülkede 4 kablo ile çalıştırmanız gerekiyorsa, sarı ve maviyi
birleştirerek kullanın.
- Ana şalteri açın. Motor dönmeye başladıktan sonra manuel konuma alarak
“aşağı – yukarı” butonları ile hareket ettirin eğer ki motor hareket etmiyorsa
Bunun neden motor dönüş yönünün ters olmasıdır lütfen elektrik faz
uçlarından birini yer değiştiriniz.
- Makineyi Basınç aralığı ve mesafe aralığı. Olmak üzere 2 farklı ayarda
kullanabilirsiniz. Basınç aralığında; pres istenilen basıncı uyguladığında yukarı
doğru kalkar. Mesafe aralığında ise belirlenen alt ve üst konumlar arasında
hareketi gerçekleştirir.
- Makinemizde numaratörü her iş bitimi, üzerindeki düğmeye basmak kaydı
ile
sıfırlayabilirsiniz.
- Pres mapası kalıba takılır ve iyice sıkılır.
- Kalıbın 2 cıvatasını da gevşeterek yerleştirin.
- Alt ve üst kalıp birleşinceye kadar presi indirin.
- Kalıp tamamen kapandıktan sonra önce üst sonra alt cıvatalarını sıkın.
9
- Presi istenilen hareket aralığının en üstüne kadar çıkartıp, üst mesafeyi
sabitleyin ve aynı şekilde alt mesafeyi de ayarlayın
(Min. 10mm, Max. 110 mm mesafe aralığında çalışmaktadır. ). Makine artık
tam otomatik, pedal ve el ile çalıştırılabilir.
Dikkat Edilmesi Gereken Hususlar:
- Pres alt tablasında hiçbir toz veya metal olmamalıdır.
- Presin önündeki güvenlik bariyerlerinin arasında hiç bir şey olmamasına
özen gösterin aksı takdirde pres aşağı ve yukarı hareket etmeyecektir
- Makinenin çalışırken özelikle hareket bölgesinden uzuvlarınızı uzak
tutun, uzun saçlarınızı toplayarak çalışın.
- Presin etiketlerindeki düğmeleri ve aletleri tamamen öğrenmeden pres ile
çalışmayınız.
10
Makine Bakım ve Onarımı:
- Periyodik olarak tüm hareketli parçaları ve ek noktalarını yağlayın.
- Presi her zaman temiz, kuru, zor şartlardan uzak tutun.
- Hidrolik yağ seviyesi makinedeki gösterge ile kontrol edilebilir. Yağ
değişirken pistonun tam çekilmiş durumda olmasına dikkat edin.
- Makinenin verimi düşmeye başlarsa, makinenin içinde sıkışmış olabilecek
havayı boşaltınız.
- Kullanılmayan zamanlarda temiz, çocukların ulaşamayacağı bir ortamda
piston tam çekilmiş konumda muhafaza edin.
11
CONTENTS:
. Technical Specifications
. General Description
. Mounting Sketch
. Parts List
. Use The Preparation of The Machine
. Electric Panel
. Control Panel
. Issues to Be Considered
. Machinery Maintenance and Repair
12
Technical Specifications:
Width, Size, Height : *102 *73 *185
Net Weight : 470 Kg
Electric Used : 380 Volt / 50 HZ
Used Air : Min. 4 Bar
Engine Power : 7.5 Kw
Number of Printing Presses : 170 Adet/min.
General Descriptions:
* CE - certified Presses are quaranteed for 2 years expcept for usage
errors.
* Use the properties leaflets used oil hydraulic oil is No. 37.
* Machines are the standard features of 110mm stroke length is.
13
Mounting Sketch:
Parts List:
1. Up
2. Down
3. Press Guide Shaft
4. Place of Mould
5. Pressure Indicator
6. Pressure Adjustment
7. Automatic
8. Bottom Plate
9. Drawer
14
Electric Panel :
1. Motor Protection Switch
2. W-Automat
3. Power Contactor
4. Down Valve Relay
5. Up Valve Relay
6. Contactor Relays
7. Lower Sensor Relay
8. Upper Sensor Relay
9. Photocell Relay
15
Control Panel :
1. Switch for air
2. Set to the upper position of the pressing movement
3. Set to the bottom position of the pressing movement
4. Shows the direction of press with the lights
5. Pressure indicator
6. Pressure adjustment
7. Switch for automatic status
16
1. Provides upward movement in the press.
2. On-Off main switch
3. Emergency stop
4. Shows how many times the pressure of the press.
5. Allows the movement of the press down.
6. Pressure switch
7. Pedal, provide using the machine with feet.
8. Manual or automatic switching
Use The Preparation of The Machine:
- fill at least more than half of oil tank with 37-46 number a hydraulic oil.
- Plug in the power cord.
- 380 V and triphase also there are 5 pieces cable on the machine.
17
These are;
Yellow cable is ground wire, blue cable is neuter, black and brown are
phase cables. If you have to run with 4 cables , connect the yellow
and the blue wire to each other.
- Turn on the main switch. After starting the engine to turn , set
manually and try up down buttons. If the buttons are not working,
replace one end of the power phase.
- The machine can be used in two different ways; pressure range and
distance range. In pressure range, after the desired pressure goes up. In
distance range, moves between desired upper and lower position.
- After the end of working on machine, can reset counter with button.
- Press lugs fitted to the mold and thoroughly tightened.
- Loosen up 2 bolt of mould and to bed its place.
- Push to down button until upper and lower molds join together.
- After acquiring the mold, tighten first top of bolts then the lower.
- Lift press top of the opperations range and set top range.
18
- Set bottom range in the same way (Min. 10mm, Max. 110 mm working
distance range).
- The machine is now operated with fully automatic and manually and pedal.
Issues to Be Considered:
- No dust or metal should press the bottom tray.
- There must be nothing in front of the safety barriers of press otherwise
press does not work.
- Keep your hands away from the working area of the press and operator
must collect if has long hair.
- Do not attempt before learn completly pressing the buttons and tools.
Machinery Maintenance and Repair:
- Periodically lubricate all moving parts and additional points.
- Always keep it clean, dry and keep it away forcing conditions.
- Hydraulic oil level can be control from indicator. Make sure piston on top
position when you change oil.
19
- The machine's efficiency begins to fall, drain the air that may be trapped
inside the machine.
- When not in use, keep the machine clean, piston on top position and out
the reach of children.
20
Steel Mould and Machine
Address: Atatürk District Marmara Industrial Site
R Blok No:455 İkitelli - Küçükçekmece - İstanbul
Tel: +90 212 494 44 60
Fax: +90 212 494 44 61
Web: http://www.steelkalip.com/
E-mail: [email protected]
Address: Urom Persia Gold Address: Ltd. 13,Tsurupa str. MOSCOW &Jewelery PR.Co. Tel/Fax: (495) 718 41 01
Fahkt Atayi Bldy No:4 Atayi www.jeweller-partner.ru
Ave - Uromieh IRAN E-Mail: [email protected]
Phone: +98 441 223 52 98
Fax : +98 441 224 38 08
Cell: +98 914 346 37 62
Cell: +90 530 602 30 16
Cell: +90 530 602 30 15
www.urompersia.ir
E-Mail : peyman@urompersia