INSTRUCTION FOR USE AND MAINTENANCE

Electric wall mounted shower stretcher art. 155040 Electric wall mounted changing table art. 155140

INSTRUCTIONS FOR USE AND MAINTENANCE

Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140, is a medical device in compliance with Directive 93/42/EGS and technical standard CE EN 60601-1, CE EN 60601-2-52.

Timo d.o.o. Ajdovščina, Vipavska cesta 4i, 5270 Ajdovščina, Tel. 00386 (0)5/3689 330, Fax 00386 (0)5/3663805 e-mail: info@timo.si http://www.timo.si

Carefully read these instructions before instalation

2

LIST OF CONTENTS 1. INTRODUCTION …………………..………………………………………………… 5

1.1. Congratulations………. ……………………………………………………………5 1.2. Assistance ……………………..………………………………………………….. 5 1.3. Warranty ………………………………………..………………………………… 5 2. INFORMATION ……..……………..………………………………………………… 6

2.1. Intended use …………. ……………………………………………………………6 2.2. Product description ..…………..………………………………………………….. 6 3. SAFETY ……….……..……………..………………………………………………… 8

3.1. General safety rules …. ……………………………………………………………8 3.2. Specific safety rules..…………..………………………………………………….. 9 3.3. Outstanding risk areas…………………………………………………….………..10 3.4. Wall mounted shower stretcher and changing table safety devices………………..10 3.5. Trained personnel…………………………………………………………………..11 4. POSITIONING OF SYMBOL TAGS APPLIED TO THE WALL MOUNTED

SHOWER STRETCHER AND CHANGING TABLE ……………………………..…11 5. TECHNICAL DETAILS ……………………………………………………………….12

5.1. Wall mounted shower stretcher and changing table specification………………….12 6. HANDLING ………………………………………………..…………………………. .13 6.1. Lifting from the package …………..…..…………………………………………...13 6.2. Storage….. ………………………………………………………………………….14 6.3. Transport…………………………………………………………………………….14 7. INSTALATION………………………………………………………………………….14 7.1. Wall mounting ………………………………………………………………………15 7.2. Assembly…………………………………………………………………………….15 8. CONTROLS……………………………………………………………………………...16 8.1. Use …………………………………………………………………………………..17 8.2. Manual Controls …………….………………………………………………………17 8.2.1. Backrest section movement (art. 155040)………………..………..………….17 8.2.2. Side rails movement ………………………………………………………….18 8.2.3. Positioning of mattress platform into vertical position ………………………18 8.3. Electrical regulations……………………………….………………………………..19 8.3.1. Raising and lowering the mattress platform…………………………………..19 9. CLEANING AND DEZINFECTION……………………………………………………20 9.1. Cleaning …………………….……………..………………………………………...20 9.2. Desinfection………………………………………………………………….….…...20 10. MAINTENANCE.………………………………………………………………………. 20

10.1. Lubrication …………………………………………………………………………20 10.2. Checking retention parts …………………………………………………………...21 10.3. Electrical part list …………………………………………………………………..21 10.4. Charging of battery…………………………………………………………………21

11. TROUBLESHOOTING……………………………………………………………........ .22 12. SCRAPPING AND DISPOSAL ……………………………………………………........22 13. ATTACHMENTS…………………………………………………………………………23 13.1 Spare parts wall base ……………….………………………………………………..23 13.2. Parts list of the mattress platform (art. 155140)…………..………..………………..24 13.3. Parts list of the mattress platform (art. 155040)…………..………..………………..25 13.4. Parts list of the mattress and pillow …………………………….……………….…..26

3

ATTENTION! This manual must be carefully read before transporting, installing or using the Electric wall mounted shower stretcher art. 155040 and Electric

wall mounted changing table art. 155140.

﹟ It must be carefully kept in a place known to persons in charge and to transport, installation, operation, maintenance, repair and disposal operators, etc.

﹟ This manual explains how the equipment is to be used and provides instructions relating to transport, installation, assembly and use. It also explains how to replace accessories and warns of outstanding risks, etc.

﹟ Always remember that the instruction manual can never fully replace adequate operator experience; in the case of some specific and difficult operations, this manual represents a memo of the main operations to be performed by operators with specific experience, acquired for instance by attending training courses on the manufacturer's premises.

﹟ This manual should be considered an integral part of the equipment and must be looked after until this is scrapped. In case of loss, ask the manufacturer for a new copy.

﹟ Make sure all the users have fully understood how to use the equipment and the meaning of the symbols affixed to such equipment.

﹟ Any accidents can be avoided by following the technical instructions compiled in accordance with relevant EEC directives …

﹟ In any case, always abide by national regulations.

No part of this manual can be reproduced without the express permission of TIMO d.o.o. Ajdovščina.

The information contained in this manual is subject to amendment. TIMO d.o.o. Ajdovščina reserves the right not to provide prior notice of such amendments.

Do not remove or deteriorate the protections, labels and notices.

4

SYMBOLS

Symbols used in this manual.

GENERIC HAZARD

IMPORTANT!

Abide by the ins-tructions in the follo-wing paragraphs

OPERATOR TYPE A

Equipment user

OPERATOR TYPE B

Equipment maintenance technician

IN CONFORMITY WITH DIRECTIVE

93/42/EC

DATE OF MANUFACTURE

5

1. INTRODUCTION 1.1. Congratulations

Dear Customer, we should like to congratulate you for having preferred one of our products. Each TIMO d.o.o. Ajdovščina product is built according to applicable safety regulations, to protect operators and service users. This manual describes and illustrates the various transport, use and adjustment operations, for better using and looking after your equipment.

Please carefully read the instructions and information contained in this manual.

1.2. Assistance

TIMO d.o.o. Ajdovščina technicians will be pleased to provide any routine and special maintenance services.

Maintenance requests should be made to TIMO d.o.o. Ajdovščina by phone or fax ((tel. 05/36 89 330 fax. 05/36 63 805). If your hospital equipment has been purchased through one of our authorised dealers and assistance or repairs are required, please contact the dealer or another authorised after-sales service centre directly.

1.3. Warranty The products of TIMO d.o.o. Ajdovščina are covered by a 1-year warranty starting on the day of shipment. The warranty does not cover component parts covered by a separate original manufacturer's warranty.

The warranty is valid as and from the date of shipment of the equipment.

The warranty shall only be considered valid if the equipment has been used correctly, following the instructions provided in this manual. Faulty parts will be repaired or replaced free of charge by TIMO d.o.o. Ajdovščina at its factory at Ajdovščina (SLO) or at the authorised dealer's.

In case of replacement of faulty parts, TIMO d.o.o. Ajdovščina shall be entitled to withdraw these after replacement. Transport and shipping costs relating to spare parts shall be charged to the buyer.

In the event of labour being required for installations and/or replacements of faulty parts made on the buyer's premises, relevant costs shall be borne by TIMO d.o.o. Ajdovščina, while the buyer shall pay all travel expenses.

Any special jobs to be done by the technicians of TIMO d.o.o. Ajdovščina shall be agreed upon case by case.

The warranty shall not cover expendable materials and periodical maintenance and parts damaged as a result of improper equipment

6

use.

Repairs and/or replacements made under warranty shall not extend the duration of the warranty, excepting the replaced part/s.

Acknowledgement of the warranty excludes any request for temporary replacement with similar equipment, excepting prior agreement between the parties.

2. INFORMATION 2.1. Intended use

Before using the Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140, the user should ascertain that both it and any accessories are in good condition by making a sight check.

Intended use The Electric wall mounted shower stretcher art. 155040, has been planned and created for the treatment and bathing of patient, particularly in every-day care use. Entirely made of epoxy – coated steal with a special cataphoresis anti-corrosion treatment, following criteria of safety for the patient and the operator. The Electric wall mounted shower stretcher art. 155040 have possibility of electric regulation of height, the manual regulation of back rest, and manual regulation of mattress platform into vertical position against the wall. The Electric wall mounted changing table art. 155140, has been planned and created for the treatment and changing of patient, particularly in every-day care use. Entirely made of epoxy – coated steal with a special cataphoresis anti-corrosion treatment, following criteria of safety for the patient and the operator. The Electric wall mounted changing table art. 155140 have possibility of electric regulation of height and manual regulation of mattress platform into vertical position against the wall. Use not in accordance with that intended use by TIMO d.o.o. Ajdovščina shall result in the company disclaiming all liability for injury to persons and damage to things.

2.2. Product description The Electric wall mounted shower stretcher art. 155040, manufactured by TIMO d.o.o. Ajdovščina, have been designed taking into account operating requirements and are suitable very easy care and bath immobile people - patients. The Electric wall mounted changing table art. 155140, manufactured by TIMO d.o.o. Ajdovščina, have been designed taking into account operating requirements and are suitable very easy care and changing bath immobile people - patients.

CLASSIFICATION

Class I according to 93/42/EC

7

The design of the structural elements and the safety distances between moving parts comply with applicable safety norms. The features listed below have been specially conceived for intended use, patient assistance and control by staff.

Description of The Electric wall mounted shower stretcher art. 155040 TIMO d.o.o. Ajdovščina, has produced The Electric wall mounted shower stretcher art. 155040 for the shower, which is designed to care and bath immobile persons - patients. The Electric wall mounted shower stretcher art. 155040 is in size and design made by us in relation to its modern form and function, allowing very easy care and bath immobile people - patients. It is attractive, user – friendly, easy – to – maintain. Mattress and pillow are made of special laminated canvas. The Electric wall mounted shower stretcher art. 155040 have possibility of electric regulation of height, the mattress platform is two-section with manual regulation of backrest from 0° to 30° and manual regulation of mattress platform into vertical position against the wall. The manual regulation of mattress platform into vertical position against the wall is perfect for the small bathroom, after use of it not take a lot of space. The Electric wall mounted shower stretcher art. 155040 is safe for both the patient and the user. By positioning the mattress platform in the correct height, transfer can be easily made from other aids such as beds, stretchers, shower seats and wheelchairs. Construction made from epoxy – coated steal with a special cataphoresis anti-corrosion treatment. With max load of 200 kg. Standard equipment of The Electric wall mounted shower stretcher art. 155040: - safety side with a special mechanism for lowering and lifting - flexible drain hose - mattress and pillow Description of The Electric wall mounted changing table art. 155140 TIMO d.o.o. Ajdovščina, has produced The Electric wall mounted changing table art. 155140 for the changing, which is designed to care and changing immobile persons - patients. The Electric wall mounted changing table art. 155140 is in size and design made by us in relation to its modern form and function, allowing very easy care and changing immobile people - patients. It is attractive, user – friendly, easy – to – maintain. The Electric wall mounted changing table art. 155140 have possibility of electric regulation of height, the mattress platform is one-section and manual regulation of mattress platform into vertical position against the wall. The manual regulation of mattress platform into vertical position against the wall is perfect for the small bathroom and changing room, after use of it not take a lot of space. The Electric wall mounted changing table art. 155140 is safe for both the patient and the user. By positioning the mattress platform in the correct height, transfer can be easily made from other aids such as beds, stretchers, shower seats and wheelchairs. Construction made from epoxy – coated steal with a special cataphoresis anti-corrosion treatment. With max load of 200 kg. Standard equipment of the electric wall mounted changing table art. 155140: - safety side with a special mechanism for lowering and lifting Possible variants of regulation: fig. 1 - maximum height of mattress platform (art.155040)

fig. 2 - minimum height of mattress platform (art.155040)

fig. 3 - raised headrest (art.155040)

fig. 4 - regulation of mattress platform into vertical position against the wall (art.155040)

fig. 5 - minimum height of mattress platform (art.155140)

fig. 6 - regulation of mattress platform into vertical position against the wall (art.155140)

8

Fig.1 Fig.2

Fig.3 Fig.4

Fig.5 Fig.6

3. SAFETY 3.1. General safety rules

Compliance with safety regulations puts the operator in a position to work profitably without causing injury to him/herself or others.

Using the equipment for purposes other than those previously described is forbidden (2.1 INTENDED USE). The equipment must only be used by properly trained personnel.

Before starting to operate the Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140, the operator must be perfectly aware of how the Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140 works, of where the controls are located and of all technical-functional features. Such awareness can be acquired by carefully reading this manual.

The nursing staff must properly inform patients how the Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140 works. The individual controls must be carefully explained so the patient can operate the bed

9

properly.

After such information has been provided, the patient should be asked to "trial run" the Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140.

The nursing staff is therefore responsible for teaching patients to use the

Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140 correctly.

All operators must abide by the accident-prevention regulations of the country where the stretcher is installed and international regulations in order to prevent any possible accidents.

3.2. Specific safety rules

Tampering with or replacing parts of the equipment without the express authorisation of TIMO d.o.o. Ajdovščina is forbidden.

The use of accessories, or spare parts, other than those recommended and/or shown in this manual can represent a hazard for operators and/or damage the Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140.

Any alterations to the equipment not expressly authorised by TIMO d.o.o. Ajdovščina shall relieve the latter of all civil and criminal liability.

Removing any safety or protection devices on the appliance is strictly forbidden; periodically, at weekly intervals, check the integrity of such devices and make sure they are working properly.

Before carrying out any maintenance or repair jobs on the equipment, the operator should have carefully read and understood the technical information provided in this manual.

All maintenance and repair jobs must be done by skilled personnel; see par. 3.5 TRAINED PERSONNEL.

Bad repairs and maintenance can represent a hazard for the user.

IMPORTANT!!!

The equipment should not be started when:

﹟ it has fallen and/or shows signs of evident damage,

﹟ the moving parts (lever mechanisms, actuators, rotation fulcrums, etc.) produce strange noises not in conformity with proper operation.

﹟ instability not in conformity with the structure occurs during operation and movement.

10

Never position the equipment close to heat sources. The Electric wall mounted shower stretcher art. 155040 and Electric wall Mounted changing table art. 155140 have to be fixed on the wall.

The movement area is required to be at least 220 cm wide and 160 cm hight free of any obstacles in order and devoid of objects that could restrict free movement.

The instructions, accident-prevention rules and warnings contained in this

manual must always be followed.

3.3. Outstanding risk areas

In some parts of the equipment, residual risks exist that cannot be eliminated during the design stage. Each operator should be aware of the outstanding risks relating to this equipment in order to prevent any accidents. Such hazards are listed below:

CRUSHING When adjusting the height of the stretcher top, raising or lowering the side rails and lowering the backrest section, outstanding risks exist of the hands being crushed between the moving parts of the mattress platform and the fixed wall stretchers structure (outstanding risk of being crushed). During wall stretchers positioning, be careful not to crush people or things between the head end and the walls against which the wall stretchers is rested (outstanding risk of crushing).

ACCIDENTAL FALLING When getting in and out of the wall stretchers, make sure the height of the stretchers is consistent with the motory capacity of the patient. If necessary, position the wall stretchers in the most correct way (outstanding risk of falling).

3.4. Wall mounted shower stretcher and changing table safety devices safety devices The Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140, manufactured by TIMO d.o.o. Ajdovščina, have been designed taking into account operating requirements and are suitable very easy care, changing and bath of immobile people - patients. To this intent, they feature various safety devices. MEHANICAL: Safety side rails 1) Prevent the patient accidentally falling out of the wall stretcher once the safety sides is

positioned as shown in fig. 7

11

fig. 7

2) Permit free access from the wall stretcher once the safety sides is positioned as shown fig. 8

fig. 8

3.5. Trained personnel

The Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140, manufactured by TIMO d.o.o. Ajdovščina, have been designed taking into account operating requirements and are suitable very easy care and bath immobile people - patients, must be used by the following professional person:

The "OPERATOR" , is the person appointed to operate the equipment (medical nursing staff); operations should be restricted to the controls indicated in Chap 8-9. This person should be perfectly aware of all the precautions and operating instructions indicated in this manual.

The operator is forbidden from performing operations other than those indicated in Chap. 8-9.

The “MAINTENANCE TECHNICIAN" , is the person appointed to transport, install, start, adjust, clean, repair, change the equipment and perform maintenance on the wall stretcher. Such person must be adequately trained and have attended workshops and training courses, etc....., and have experience as regards transporting, installing, operating and servicing medical-sanitary appliances and systems.

4. POSITIONING OF SYMBOL TAGS APPLIED TO THE WALL MOUNTED STRETCHER

The purpose of the signs is to inform operators of any existing risks. Each operator should be able to recognise the meanings of such signs.

12

The CE plate data must always be quoted when requesting assistance or spare parts. The adhesive signs and fitted plates must never be removed, tampered with or destroyed. The persons in charge of company safety must replace them in case of deterioration or illegibility.

TIMO d.o.o. Ajdovščina is at your disposal for providing replacement stickers or plates.

1

Indicates the lever for lowering the

stretcher backrest

2

JUST SAMPLE OF PLATE

A) Artikel No.

B) Serial no.

C) Safe working load

D) Max lifting load

E) Description – type

F) Symbol CE

3

Name of producer

5. TEHNICAL DETAILS The products of the company TIMO d.o.o. Ajdovščina, are subject to continous upgrading and consequently the technical specifications of the product may be changed without prior notice.

5.1. Wall mounted shower stretcher and changing table specification

Dimension and degree art. 155040 length A

[mm] width B [mm]

height [mm]

degrees [°]

Mattress platform 1910 650

Head rest 630 650 0-30

Dim. of wall stretcher in horizontal position »folded position«

2050 1000

Dim. of wall stretcher in vertical »lying position ”

2050 500

Min. height 450

Max. height 850

13

Dimension and degree art. 155140

length A [mm]

width B [mm]

height [mm]

degrees [°]

Mattress platform 2000 700

Dim. of wall stretcher in horizontal position »folded position«

2000 1000

Dim. of wall stretcher in vertical »lying position ”

2000 500

Min. height 450

Max. height 850

Tehnical details Safe working load 200 kg

Max. lifting load 200 kg

The wall stretcher weight 100 kg

Useful life 10 let

Tehnical details Battery 24 V DC / 1 x 2,9 Ah Max input 4 A Degree of protection IPX6 Operation procedure 10%, max 2min/18min Charger 100 - 240 V / 50 - 60 Hz / 650mA Weight of the wall stretcher 100 kg

6 HANDLING 6.1. Lifting from the package

Lifting from the package must only be done by skilled personnel, trained to perform this type of operation.

The Customer is responsible for obtaining the equipment suitable for lifting from the package the wall stretcher.

Before lifting from the package the wall stretcher, make sure no one is standing within range of operation.

The weight to be lifted is the weight of the wall stretcher (see table “Technical Details”) plus any packaging material and accessories.

Check the suitability of the means used, such as: cables, straps, hooks, crane trucks or bridge cranes, which must be able to lift over 300 Kg.

14

Lift from the package the wall stretcher have to be moved as little as possible off the floor.

Make sure during lifting from the package that the wall stretcher is

perfectly balanced and avoid operations that could make it unstable.

6.2. Storage of the wall stretcher In case of storage for a long period of time (6 or 12 months), proceed as follows: • make sure the room where the wall stretcher is placed is dry and that temperature, humidity and

atmospheric pressure values are within the following parameters: temperature between 0˚ and +40˚, atmospheric pressure between 700mB and 1060mB air humidity max 70%

Do not stack the wall stretcher one on the top of the other.

6.3. Transport

The Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140, manufactured by TIMO d.o.o. Ajdovščina, are shipped to customers in two parts ( the wall fitting panel and mattress platform lying part.) The wall fitting pannel have to be fitted to a wall as described in that instruction in chapter 7. Than you have to fit the mattress platform lying part as described in that instruction in chapter 7. Transport is generally done by truck. The temperature, humidity and atmospheric pressure values during transport must fall within the following parameters: temperature between 0˚ and +40˚, atmospheric pressure between 700mB and 1060mB air humidity max 70% 7. INSTALATION

The wall decoration and floor covering must be completed and finished

The wall area is required to be at least 220 cm wide and 160 cm hight, flat, plumb and clear of any obstacles.

The wall stretcher have to be clear of any side walls, fixtures, handrails or appliances by 50 mm at the sides and by 400 mm minimum (700 mm mm recommended) at the front.

15

7.1. Wall mounting Instruction to fitting on the wall:

(please see fig. 9) The wall fitting panel is fixed to the wall and normally rest on the floor. The wall have to be load bearing, strong enough to carry a 150 kg load on each of the wall ficings (screw fi 10x100) The wall area is required to be at least 220 cm wide and 160 cm hight, flat, plumb and clear of any obstacles. (please see fig. 10) The wall fitting panel is fixed to a stud wall and normally rest on the floor. The fitting to a stud wall need special reinforcement; either noggins as shown in fig. 10 (plywooden reinforcements dim. 200x50 mm). The wall have to be load bearing, strong enough to carry a 150 kg load on each of the wall ficings (screw fi 10x100). The wall area is required to be at least 220 cm wide and 160 cm hight, flat, plumb and clear of any obstacles.

The plywood support must be in contact with and supported by the floor.

The wall fitting panel cannot be fitted to metal frame or similar type stud wall unless it has been fully reinforced with timbers struts that are secured at the top and bottom and noggins or plywood fitted as per our specification

fig. 9 fig. 10

7.2. Assembly

When the fitting of the fitting panel is finished you can star with fitting of the mattress platform lying part. (please follow as shown on fig. 11)

- star with fitting of the cover panel 1 (1. step) - star with fitting of the cover panel 2 (2. step)

plywooden reinforcements 200x50mm

16

- screw the central box (3. step) - insert the battery (4. step) - screw the safety side (5. step)

The central box and battery have to be mounted vertically

fig. 11

8. CONTROLS

Before using the Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140, make sure you are perfectly acquainted with the instructions concerning the controls.

Prior to enabling the various the Electric wall mounted shower

stretcher art. 155040 and Electric wall mounted changing table art. 155140 movements, make sure the patient does not have his/her arms or legs located in any opening, for example in the protection side rail.

Before using some of the functions (the Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140 height lowering, backrest lowering), make sure that nothing and no one (especially children) is underneath the mattress platform.

During raising and lowering movements of the Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140, make sure the wall stretcher is at minimum height. Never leave the patient alone on the Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140 without the supervision of nursing staff!

17

8.1. Use

To use the wall stretcher, the operator must follow the instructions: 1) position the mattress platform as low as possible with respect to the floor before leaving the patient

alone.

ATTENTION!! Always tell the patient to get in and out of the wall stretcher with the mattress platform in fully-lowered position.

8.2. Manual controls 8.2.1. Regulation of backrest (art. 155040)

In case of emergency, the backrest section can be quickly lowered by means of the handle underneath the mattress platform on the front side.

8.2.1.1. Raising the backrest section

1) Grip the backrest part.

2) Pull the handle at the side of the mattress platform upwards, without forcing (fig. 12).

fig. 12

3) Rise up the platform as far as desired position.

4) First release the handle and then the backrest.

8.2.1.2. Lowering the backrest section (art. 155040) 1) Grip the backrest part.

2) Pull the handle at the side of the mattress platform upwards, without forcing (fig. 12).

3) Rise down the platform as far as desired position.

4) First release the handle and then the backrest.

18

Make sure there is nothing to prevent the backrest being returned to horizontal position.

8.2.2. Side rails movement

Prior to enabling the various wall stretcher movements, make sure the patient does not have his/her arms or legs located in any opening, for example in the protection side rail.

Raising the side rails Firmly grip the top part of the side rail (fig.13) then lift it to end and stroke and ascertain that it is effectively hooked.

When you raise side rail always check that it is properly locked in place!

fig. 13

Lowering the side rails Firmly grip the top part of the side rail and lift the part that is marked with the red arrow as shown (fig.14) and with the other hand squeezed the trigger lever together and release the safety side, until the lower position is reached.

fig. 14

8.2.3. Positioning of mattress platform into vertical position The manual regulation of mattress platform into vertical position against the wall is perfect for the small bathroom, after use of it not take a lot of space. Fig 15

slika. 15

Positioning of mattress platform into vertical position:

1. Lower the mattress platform at the min. height (fig. 16)

19

2. The side rails needs to be lowered (fig. 17) 3. Grib the mattress platform and folded up it agains the wall (fig. 18) 4. When the matress platform is folded up agains the wall we can close the side rail (fig. 19)

fig. 16 fig. 17 fig. 18 fig. 19 Positioning of mattress platform into horizontal position:

1. Grip the mattress platform and folding down the stretcher fig. 20

Fig . 20

When folding down the steretcher, ensure that there are no obstacles or person under the stretcher!

8.3 Electric regulation of the wall stretcher Electric regulation of the wall stretcher: - Lifting and lowering of mattress platform All movements can be performed for a maximum time of 2 minutes. After this time a thermal cut out will interrupt movements until resetting. Expected rest period = approx. 18 min. Movements will start again automatically after this time.

ATTENTION!! Always tell the patient to get in and out of the wall stretcher with the mattress platform in fully-lowered position.

8.3.1. Lifting and lowering of mattress platform Lifting and lowering the mattress platform of the wall stretcher is regulated with the push-button handset. Mattress platform of the wall stretcher will be lift or lower by pressing the button and hold it until the desired height is reached.

Make sure nothing and no one hinders the shower trolley during the regulation of lowering.

20

fig. 21

Before using some of the functions (the Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140 height lowering, backrest lowering), make sure that nothing and no one (especially children) is underneath the mattress platform.

9. CLEANING AND DESINFECTION

9.1. Cleaning The wall stretcher can be cleaned by washing with water, neutral detergents and a sponge; it can be rinsed with water and a sponge.

NEVER USE high pressure cleaners, acids, solvents, corrosive products and abrasive substances. The detergents must not contain phosphates, phosphorus or formaldehyde.

9.2. Disinfection The wall stretcher disinfection must be done using suitable non-corrosive products. Disinfectants must not contain phosphates, phosphorus or formaldehyde and must have a pH between 6 and 8. NOTE: The temperature of the washing water must not be above 85 °C.

10. MAINTENANCE

All maintenance operations must be done by skilled personnel.

10.1. Lubrication

All maintenance operations must be done by skilled personnel!

After each operation of sanitation, especially by washing, it is recommended to lubricate the joints and moving parts with silicone-based lubricants. Periodically (at least every 6 months), make sure all the retention parts are tight (screws, pins, nuts, etc.) and check the condition of joints.

21

10.2. Checking retention parts

All maintenance operations must be done by skilled personnel!

Periodically (at least every 6 months), make sure all the retention parts are tight (screws, pins, nuts, etc.) and check the condition of joints.

Periodically (at least every 6 months), it have to be done the service check by authorised servicer. All this check – services have to be noted in service book with date and sign of service done. Only with the signed service book the warranty is valid.

10.3. Electrical diagram

Electrical scheme:

A central box CBJ 2 -Linak CBJ2 B battery BAJ 1 -Linak BAJ1 C manual control HB 81 -Linak J00724 D actuator LA 44 -Linak 442100 E cord motor -Linak 914573 H Battery Charger CHJ 2 -Linak CHJ2 Connecting the battery on a wall charger (CHJ2) and on box (CBJ 2). Battery is inserted into CHJ2 or CBj 2 to place it on the bus and pushed it into place. Remove the battery from CHJ2 or CBJ 2 by holding the handle at the back of the battery and then press it to remove the battery. 8.3.1. Charging the battery

How do we know when we have to connect the battery charger? When the voltage drops below a certain point we hear a sound signal, which informs us that it is necessary to connect the battery charger. Wall battery charger has two signal lights (yellow and green). Green light shows when the charger is connected to power. Yellow light is turn on when the battery is charging when the battery is fully charged, the yellow light turns off. Charging the battery takes about 4 hours.

Before first use the battery have to be connected 12 hours!

Do not charging the battery in bathroom!

22

11. TROUBLESHOOTING

Preface

All maintenance operations must be done by skilled personnel!

This chapter lists some of the most probable problems that could affect proper the wall stretcher operation. Solutions to these problems have been offered in the troubeshooting guide.

If the problems persist and repeat themselves with some frequency even after applying the remedies suggested in this chapter, you are kindly asked to contact our after – sales department.

ERROR CAUSE CORRECTION

The head part will not go up when you press the lever

1. Excessive load on the backrest part

2. Damage of gas springs 3. Damage of trigger

1. Reduce the load and try again by raising

2. Call a technician to replace the gas spring

3. Call a technician to replace the trigger

The mattress platform of the shower trolley is not possible to be raised

1. It is possible that the battery is completely flat or defective or is not properly connected

2. It is possible that the hand control panel is defective

3. It is possible that the actuator is defective

4. It is possible that the feeding cable is defective

5. It is possible that the control box is defective

1. Connect battery to a charger or call a technician to replace the battery 2.Call a technician to replace the hand control panel 3.Call a technician to replace the actuator 4.Check if all the electric cables are connected correctly, or call a technician to replace the feeding cable 5.Call a technician to replace the control box

12. SCRAPPING AND DISPOSAL The Electric wall mounted shower stretcher art. 155040 and Electric wall mounted changing table art. 155140, manufactured by TIMO d.o.o. Ajdovščina, is constructed mainly from ferrous and non-ferrous metals, thermoplastic materials. In the case of demolition and disposal, parts considered as special waste must be processed in accordance with curent law.

23

13. ATTACHMENTS 13.1. Spare parts of the wall fitting panel

ITEM PART NUMBER 1 Wall rails 17 Gas spring PV A2 150 2 Wall rails 18 Spacer inox ø12x1,5 3 drum ø20x45 19 tub inox ø14x1,5-15 4 Actuator Linak la44 20 Screw imbus M8 x 70 5 Side rail 21 Screw imbus M8 x 80 6 Adjustable feet ø50 - M10x50 22 Washers pvc ø40-10x4 7 Wall cover 2 23 Screw imbus - M10 x 20 8 Wall cover 24 Slider 20 9 Wall cover D 25 Plugin 25x25 10 Wall cover L 26 Support for cover 11 screw - M10 x 80 27 Screw imbus M8 x 70 12 screw - M10 x 60 28 Control box CBJ2 13 screw - M10 x 55 29 screw ø 4x15 14 screw - M10 x 60 30 Battery linak baj 15 Self-tapping nut -M10 31 Spring washer DIN 128 - A8 16 Self-tapping nut -M8 32 screw - M8 x 20

24

13.2. Spare parts of the mattress platform lying part (art.155140)

ITEM NO. PART NUMBER

1 nosilni okvir enodelne stenske preg. mize

2 ležišče 1700x700

3 safety side

4 plastic end cap ø 20

5 plastic end cap 50x30

6 plastic end cap 25x25

7 screw - M10 x 55

8 Self- locking nut-M10

9 wood screw ø 5x45

10 trigger safety side

11 screw M6x15 pvc ball head

12 spring ø10x30

25

13.3. Spare parts of the mattress platform lying part (art.155040)

ITEM NO. PART NUMBER

1 frame of wall monted shower 18 Washer DIN 125 - A 8.4

2 laminat mattress platform 1250x650 19 self- locking nut-M8

3 head rest 20 self- locking nut-M10

4 handel for regulation of back rest 21 Spring Pin ISO 8752 - 4 x 18 - St

5 trigger 22 screw - M10 x 50

6 laminat for back rest mattressplatform 650x630 23 screw - M10 x 55

7 short safety side 24 screw - M10 x 60

8 long safety side 25 rubber handle ø12x100

9 bumper wheel 26 spring ø10x30

10 gas cilinder OBKOV NHC C3 130 422 H32P5-500N 27 plastic end cap 30x30

11 plate bumper wheels 28 U frame fo cilinder 140

12 blind rivet ø4x16 29 screw M6x15 pvc ball head

13 plastic end cap ø20 30 trigger safety side

14 nayon joint 31 pin 50

15 screw - M8 x 45 32 tube right

16 screw - M8 x 25 33 tube left

17 screw - M8 x 30 34 plastic end cap 50x30

26

13.4. Parts list of the mattress and pillow

- Mattress and pillow art.155040

Art. 155040

No. item

1 Mattress – two section

2 pillow

3 Terminal women

4 Terminal men

5 Drain valve

6 flexible tube

27

Art. 155140

28

No part of this manual can be reproduced without the express permission of TIMO d.o.o. Ajdovščina.

FURNITURE FOR HOSPITALS – CLINICS – NURSING HOMES

TIMO d.o.o. Ajdovščina, Vipavska cesta 4i, 5270 Ajdovščina – Slovenija Tel. 00386 (0)5/36 89 330 Fax 00386 (0)5/36 63 805 e-mail: info@timo.si

Art. Izdelka 155040 in 155140 date 25. oktober 2013 rev. 00