manual del medidor de distancia
TRANSCRIPT
-
8/10/2019 Manual Del Medidor de Distancia
1/19
Milwaukee 2282-20 1
ENTable of Contents
Genaral Safety Instructions- - - - - - - - - - - - -2
Instrument Set-up - - - - - - - - - - - - - - - - - - - - - - -3Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3
Display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4
Insert batteries - - - - - - - - - - - - - - - - - - - - - - - - - - - -4
Labeling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -5
Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6Switching ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - -6
Clear- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6
Message Codes - - - - - - - - - - - - - - - - - - - - - - - - - - -6
Beep ON/OFF- - - - - - - - - - - - - - - - - - - - - - - - - - - - -6
Illumination ON/OFF - - - - - - - - - - - - - - - - - - - - - - - -6
Adjusting measuring reference / tripod - - - - - - - - - - -7Multifunctional endpiece- - - - - - - - - - - - - - - - - - - - - -7
Distance unit setting - - - - - - - - - - - - - - - - - - - - - - - -8
Tilt unit setting- - - - - - - - - - - - - - - - - - - - - - - - - - - - -8
Timer (automatic release) - - - - - - - - - - - - - - - - - - - -8
Measuring Functions - - - - - - - - - - - - - - - - - - -9Measuring single distance - - - - - - - - - - - - - - - - - - - -9
Permament / Minimum-Maximum measuring - - - - - - -9
Add / Subtract - - - - - - - - - - - - - - - - - - - - - - - - - - - - -9
Area- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
Volume- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11Pythagoras (2-point) - - - - - - - - - - - - - - - - - - - - - - - 12
Pythagoras (3-point) - - - - - - - - - - - - - - - - - - - - - - - 12
Pythagoras (partial height) - - - - - - - - - - - - - - - - - - - 13
Stake out - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 14
Smart Horizontal Mode - - - - - - - - - - - - - - - - - - - - - 15
Height tracking - - - - - - - - - - - - - - - - - - - - - - - - - - - 15
Memory (20 last displays) - - - - - - - - - - - - - - - - - - - -16
Delete Memory - - - - - - - - - - - - - - - - - - - - - - - - - - -16
Calibration - - - - - - - - - - - - - - - - - - - - - - - - - - - - -16Calibration of tilt sensor (Tilt Calibration) - - - - - - - - -16
Technical Data - - - - - - - - - - - - - - - - - - - - - - - - -18
Message Codes - - - - - - - - - - - - - - - - - - - - - - - -18
Care - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -19
Service - United States- - - - - - - - - - - - - - - - -19
-
8/10/2019 Manual Del Medidor de Distancia
2/19
Milwaukee 2282-202
EN Genaral Safety Instructions
WARNINGRead all safety warnings and instructions.Before using the appliance, read thesesafety instructions, the appliances oper-ators manual (found on the enclosed CD)
and all labels on the appliance. Do not allow persons unfamiliar with the
appliance, these safety instructions, andthe appliances operators manual tooperate the appliance.
This appliance can be dangerous in thehands of untrained users. Do not overreach. Keep proper footing
and balance at all times.This enables better control of the appli-ance in unexpected situations.
Ensure adequate safeguards at the worksite (e.g. surveying site when measuringon roads, construction sites, etc.)
WARNINGThe device produces visible laser beams,which are emitted from the appliance.This device is a Class 2 laser product inaccordance with IEC 60825-1:2007 Laser light - Do not stare into beam or
view directly with optical instruments.
Do not point laser light at others. Laserlight can cause eye damage. Avoid dangerous environments.Do not use in rain, snow, damp or wet loca-tions. Do not use in the presence of explo-
sive atmospheres (gaseous fumes, dust orflammable materials). Maintain appliances. If damaged, have
the appliance repaired before use.Accidents may be caused by poorly main-tained appliances. Use appliance only with specifically
designated accessories.Use of any other accessories may create arisk of injury. This tool is designed to be powered by
2-AAA batteries properly inserted intothe tool.
Do not attempt to use with any othervoltage or power supply. Do not leave batteries within the reach of
children. Do not mix new and used batteries. Do not mix brands (or types within
brands) of batteries. Do not mix rechargeable and non-
rechargeable batteries. Install batteries according to polarity
(+ / ) diagrams. Properly dispose of used batteries
immediately. Do not incinerate or dismantle batteries. Under abusive conditions, liquid may be
ejected from the battery, avoid contact. Ifcontact accidentally occurs, flush with
water. If liquid contacts eyes, addition-ally seek medical help.Liquid ejected from the battery may causeirritation or burns. Keep hands away from all moving parts.
Watch out for erroneous measurementsif the appliance is defective or if it hasbeen dropped, misused or modified.
Carry out periodic test measurements.Particularly after the appliance has beensubject to abnormal use, and before,during and after important measurements.
Do not dispose of appliance or batteriestogether with household waste material!Appliance and batteries that have reachedthe end of their life must be collected sepa-rately and returned to an environmentallycompatible recycling facility. Have your appliance serviced by a qual-
ified repair person using only identicalreplacement parts.
This will ensure that the safety of the appli-ance is maintained. Maintain labels and nameplates.
These carry important information. Ifunreadable or missing, contact aMILWAUKEE service facility for a freereplacement. The device conforms to the most strin-
gent requirements of the relevant elec-tromagnetic compatibility (EMC) stan-dards and regulations.
Yet, the possibility of causing interferencein other devices cannot be totallyexcluded.
-
8/10/2019 Manual Del Medidor de Distancia
3/19
Milwaukee 2282-20 3
ENInstrument Set-up
Introduction
The safety instructions and the user manual should beread through carefully before the product is used for thefirst time.The person responsible for the product must ensure that
all users understand these directions and adhere to them.
The symbols used have the following meanings:
WARNINGIndicates a potentially hazardous situation or an unintended usewhich, if not avoided, will result in death or serious injury.
CAUTIONIndicates a potentially hazardous situation or an unintended usewhich, if not avoided, may result in minor injury and/or appreci-able material, financial and environmental damage.
Important paragraphs which must be adhered to in practiceas they enable the product to be used in a technicallycorrect and efficient manner.
i
Overview
Display
On / Measure
Area / Volume
Measuringreference
Memory
Inclinationfunctions
Add / Subtract
Pythagoras /Stake out
Clear / Off
Timer / Units
-
8/10/2019 Manual Del Medidor de Distancia
4/19
Milwaukee 2282-20
Instrument Set-up
4
EN
DisplayHorizontalmeasure-
ment
Units
Stake out
Slope
distance
Circumfer-ence
Measuringreference
2nd result
Area / Volume
Angle
Wall area
Addition /Subtraction
Timer
Memory
Pythagoras
Battery
Min/MaxMeasuring
Main line
Indirect height
Ceiling area
Insert batteries
i
To ensure a reli-able use, do notuse zinc-carbonbatteries.Change batter-ies when batterysymbol is flash-ing.
-
8/10/2019 Manual Del Medidor de Distancia
5/19
Milwaukee 2282-20
Instrument Set-up
5
EN
Labeling
Laser RadiationDo not stare into the beam
Laser class 2
acc. IEC 60825-1:2007Maximum radiant power:
-
8/10/2019 Manual Del Medidor de Distancia
6/19
Milwaukee 2282-206
EN Operations
Switching ON/OFF Clear Message Codes
2 sec
Device isturned OFF.
i
Press ON but-ton 2 sec tostart continuouslaser mode. If
no key ispressed for 180sec, the deviceswitches off au-tomatically.
1x
Undo last action.
2x
Leave actualfunction, go to de-fault operationmode.
If the info icon appears with anumber, observe the instruc-tions in section "MessageCodes".
Example:
Beep ON/OFF Illumination ON/OFF
2 secsimultane-
ously
2 secsimultane-
ously
-
8/10/2019 Manual Del Medidor de Distancia
7/19
Milwaukee 2282-20
Operations
7
EN
Adjusting measuring reference / tripod
Distance is measured from thefront of the device.
1
Distance is measuredfrom the tripod threadpermanently.
2
Distance is measured from the rearof the device (standard setting).
3
Multifunctional endpiece
i
The orientationof the endpiece
is automaticallydetected andthe zero point isaccordingly ad-justed.
-
8/10/2019 Manual Del Medidor de Distancia
8/19
Milwaukee 2282-20
Operations
8
EN
Distance unit setting Tilt unit setting
0.000 m
0.0000 m
0.00 m
0.00 ft
000 1/32
0.00 in
0 in 1/32
Switch between thefollowing units:
2 sec 0.0 0.0 %
2 secsimultaneously
Switch between thefollowing units:
Timer (automatic release)
s
1
Adjust delay of au-tomatic release(max. 60 sec,standard setting5 sec)
2 i
Once the key is released with thelaser activated, the remaining sec-onds until the measurement aredisplayed in a countdown. The de-layed release is recommended forprecise aiming e.g. at long distanc-es. It avoids shaking of the devicewhen pressing the measurementkey.
-
8/10/2019 Manual Del Medidor de Distancia
9/19
Milwaukee 2282-20 9
ENMeasuring Functions
Measuring single distance
1
Aim active laser at target.
2
8.532m
3 i
Target surfaces: Measuringerrors can occur when meas-uring to colourless liquids,glass, styrofoam or semi-per-
meable surfaces or whenaiming at high gloss surfac-es. Against dark surfaces themeasuring time increases.
Permament / Minimum-Maximum measuring
1
2 sec
8.532mUsed to measure room diagonals (maximum val-ues) or horizontal distance (minimum values)
The minimum and maximum dis-tance measured is displayed(min, max.). The last value meas-ured is displayed in the main line.
min. max.
2
Stops permanent / minimum-maximum measuring.
3
Add / Subtract
7.332m
1
The next meas-urement is addedto the previousone.
2
The next meas-urement is sub-tracted from theprevious one.
2x
5.515m
12.847m
3 i
The result is shown in themain line and the measured
value above. This processcan be repeated as required.The same process can beused for adding or subtractingareas or volumes.
-
8/10/2019 Manual Del Medidor de Distancia
10/19
Milwaukee 2282-20
Measuring Functions
10
EN
Area
1
1x
2
Aim laser at firsttarget point.
3 4
Aim laser at sec-ond target point. 24.352m
2
5 iThe result is shown in themain line and the measured
value above.
19.823m
24.352m2
2 sec Circumference
Area
6
-
8/10/2019 Manual Del Medidor de Distancia
11/19
Milwaukee 2282-20
Measuring Functions
11
EN
Volume
1
2x
2
Aim laser at firsttarget point.
3 4
Aim laser at sec-ond target point.
5 6
Aim laser at thirdtarget point.
78.694m3
7 i
The result isshown in themain line andthe measured
value above.208.703m
2
80.208m
78.694m3
24.224m2
208.703m2
80.208m
78.694m3
2 sec
8Circumference
Wall areas
Ceiling/floor area
Volume
-
8/10/2019 Manual Del Medidor de Distancia
12/19
Milwaukee 2282-20
Measuring Functions
12
EN
Pythagoras (2-point)
1 2
Aim laser at up-per point.
3 4
Aim laser rectan-gular at lowerpoint.
8.294m
5 i
Notice additionalPythagorasmeasurement in-
formation at thebottom of thenext page.
Pythagoras (3-point)
1
2x
2
Aim laser at up-per point.
3 4
Aim laser at rec-tangular point.
5 6
Aim laser at lower point.
8.294m
7 i
Notice additional
Pythagorasmeasurement in-formation at thebottom of thenext page.
-
8/10/2019 Manual Del Medidor de Distancia
13/19
Milwaukee 2282-20
Measuring Functions
13
EN
Pythagoras (partial height)
1
3x
2
Aim laser at upperpoint.
3 4
Aim laser at 2ndpoint.
5 6
Aim laser at rec-tangular point.
2.602m
7
i
Pressing the measuring key for 2 sec in the function activates automaticallyMinimum or Maximum measurement.
Pythagorasmeasurements:
-
8/10/2019 Manual Del Medidor de Distancia
14/19
Milwaukee 2282-20
Measuring Functions
14
EN
Stake out
i
Two differentdistances (aand b) can beentered to
mark off de-fined meas-ured lengths.
1
2
3
a =b
a
b
b
1
2
3
a
b
b
a =b
1.000m
1
4x
1.012mAdjust value"a".
2 3
Approve value"a".
0.625m
4
Adjust value"b".
5
Approve value "b" and startmeasurement.
6
Move deviceslowly along thestake-out line.The distance tothe next stake
out point is dis-played. 1.012m
0.240m0.240 m is missingup to next 1.012 mdistance.
i
When approaching a stakeout point to less than 0.1 mthe instrument starts tobeep.The function can be stoppedby pressing the CLEAR/OFFbutton.
-
8/10/2019 Manual Del Medidor de Distancia
15/19
Milwaukee 2282-20
Measuring Functions
15
EN
Smart Horizontal Mode
1
Aim laser attarget.
2
z
x
y
0.032m
5.204m
40.8
4.827m
xy
z
3
(up to 360 and a transversetilt of 10)
i
Press keyagain toswitch offhorizontal
measure-ment.
Height tracking
i
This function displays continous-ly the tracking height if the deviceis turned on a tripod. No 2nd dis-tance measuring is needed asonly the angle is automaticallymeasured.
1
2x
xx
Aim laser at low-er point.
2 3h1
h2h3
Aim laser at upper points andangle/ height tracking starts au-tomatically.
4
h1
h2h3
x
y
30.2
6.932m40.8
9.827m
x
y
5
= Trackingheight
= Trackingangle
i
The trackedheight "y" is in90 to the 1st
aimed point"x".
6
Stops Height tracking anddisplays last measurement.
-
8/10/2019 Manual Del Medidor de Distancia
16/19
Milwaukee 2282-20
Measuring Functions
16
EN
Memory (20 last displays) Delete Memory
8.294m
20 20 last displaysare displayed.
1
8.294m
20 Navigates trough20 last displays.
2
The value fromthe main line canbe used for fur-ther calculations.
2 sec
3
2 secsimultaneously
Memory is completely de-leted.
-
8/10/2019 Manual Del Medidor de Distancia
17/19
Milwaukee 2282-20 17
ENCalibration
Calibration of tilt sensor (Tilt Calibration)
12 sec
simultane-ously
2
Place device on absolutely flat sur-face.
3
1804
Turn the device horizontally by 180and place it again on absolutely flatsurface.
5 6
Turn the device and place it again on ab-solutely flat surface.
7180
8
Turn the device horizontally by 180and place it again on absolutely flatsurface.
9 i
After 2 secthe devicegoes backto the nor-mal mode.
-
8/10/2019 Manual Del Medidor de Distancia
18/19
Milwaukee 2282-2018
EN Technical Data
* applies for 100 % target reflectivity (white paintedwall), low background illumination, 25 C
** applies for 10 to 500 % target reflectivity, high back-ground illumination, - 10 C to + 50 C
*** Tolerances apply from 0.05 m to 10 m with a confi-dence level of 95%. The maximum tolerance maydeteriorate to 0.1 mm/m between 10 m to 30 m and to
0.2 mm/m for distances above 30 m**** applies for 100 % target reflectivity, backgroundillumination of approximately 30'000 lux
***** after user calibration. Additional angle relateddeviation of +/- 0.01 per degree up to +/-45 in eachquadrant. Applies at room temperature. For the wholeoperating temperature range the maximum deviationincreases by +/- 0.1.
For accurate indirect results, the useof a tripod is recommended. Foraccurate tilt measurements a trans-verse tilt should be avoided.
Message Codes
If the message Errordoes not disappearafter switching on the device repeatedly,contact the dealer.If the message InFoappears with anumber, press the Clear button andobserve the following instructions:
Distance measurement
Typical Measuring Tolerance* 1.5 mm / 0.06 in ***
Maximum MeasuringTolerance**
2.5 mm / 0.10 in ***
Range of target plate 80 m / 262 ft
Typical Range* 80 m / 262 ft
Range at unfavourablecondition ****
60 m / 197 ft
Smallest unit displayed 0.1 mm / 1/32 in
laser pointat distances
6 / 30 / 50 mm(10 / 50 / 80 m)
Tilt measurement
Measuring tolerance to laserbeam*****
0.2
Measuring tolerance tohousing*****
0.2
Range 360
General
Laser class 2
Laser type 635 nm, < 1 mW
Protection class IP54 (dust- and splashwater protected)
Autom. laser switch off after 90 s
Autom. power switch-off after 180 s
Battery durability (2 x AAA) up to 5000 measure-ments
Dimension (H x D x W) 117 x 57 x 32 mm4.6 x 2.4 x 1.3 in
Weight (with batteries) 0.14 kg / 4.938 oz
Temperature range:- Storage
- Operation
-25 to 70 C-13 to 158 F-10 to 50 C14 to 122 F
FunctionsDistance measuring yes
Min/Max measuring yes
Permanent measuring yes
Stake-out yes
Addition/Subtraction yes
Area yes
Volume yes
Pythagoras 2-point, 3-point,partial height
Smart Horizontal Mode /Indirect height
yes
Height tracking yesMemory 20 displays
Beep yes
Illuminated display yes
Multifunctional endpiece yes
i
No. Cause Correction
156 Transverse t iltgreater than 10
Hold the instrumentwithout any transversetilt.
162 Calibration mistake Make sure, the deviceis placed on a abso-lutely horizontal and flatsurface. Repeat thecalibration procedure. Ifthe mistake still occurs,contact your dealer.
204 Calculation error Perform measurement
again.252 Temperature too
highLet device cool down.
253 Temperature toolow
Warm device up.
255 Received signal tooweak, measuringtime too long
Change target surface(e.g. white paper).
256 Received signal toohigh
Change target surface(e.g. white paper).
257 Too much back-ground light
Shadow target area.
258 Measurementoutside of meas-uring range
Correct range.
260 Laser beam inter-rupted
Repeat measurement.
-
8/10/2019 Manual Del Medidor de Distancia
19/19
Milwaukee 2282-20
Care
19
EN
Care
Clean the device with a damp, soft cloth. Never immerse the device in water. Never use aggressive cleaning agents
or solvents.
Service - United States
MILWAUKEE prides itself in producing apremium quality product that is NothingBut Heavy Duty.Your satisfaction with our products is very
important to us!If you encounter any problems with theoperation of this tool, or you would like tolocate the factory Service/Sales SupportBranch or authorized service stationnearest you, please call...Additionally, we have a nationwidenetwork of authorized Distributors ready toassist you with your tool and accessoryneeds.Check your Yellow Pages phone direc-tory under Tools-Electric for the names &addresses of those nearest you or see the'Where To Buy' section of our website.
1-800-SAWDUST
(1.800.729.3878)Monday-Friday
7:00 AM - 6:30 PMCentral Time
or visit our website atwww.milwaukeetool.com
For service information, use the 'ServiceCenter Search' icon found in the 'Parts &Service' section.
Contact our Corporate After SalesService Technical Support about ... Technical Questions Service/Repair Questions Warranty
call: 1-800-SAWDUSTfax: 1.800.638.9582
email:[email protected]
Register your tool online atwww.milwaukeetool.com and... receive important notifications regarding
your purchase ensure that your tool is protected under
the warranty become a Heavy Duty club member