mactac technical products - nova...

MACtac TECHNICAL ProductsInnovative Supplier of Engineered Pressure Sensitive Adhesives

Product Selector - April 2012

pg. 2

Phone: 1-800-328-2619

Specialty Products Table of Contents

page

Corporate Overview 3

Technical Adhesive Constructions Single-Coated & Double-Coated 4 Free Film 4

Technical Carrier Membranes Paper, Film, Foam and Other Carriers 5

Technical Liner Categories Densified Kraft Paper Liners 6 Polycoated Kraft Paper Liners 6 Coated Kraft Lineers 6 Film Liners 7 Other Liners 7

Test Methods Peel, Shear 8 Quick Tack, Release, Other Methods 9

MACbond® 10 Rubber, Double-coated Films, Single Liner IB1101A, IB1111A, IB1161 11 IB1175AER, IB1175AERW60, IB1175AL12 12 IB1178A, IB1178AW60, IB1182 13 IB1182W60, IB1183, IB1183W60 14 IB1184W60, IB1185L12, IB1188 15 IB1190A, IB1190AW60, IB1190AP2 16 IB1200A, iB1271 IB1271W60 17

Acrylic, Double-coated Films, Single Liner IB2100, IB2101, IB2130 18 IB2132, IB2133 19 IB2141, IB2154, IB2180N 20

Acrylic, Double-coated Films, Double Liner IB2107 21

Specialty Permanent/Removable IB1250TR 22 Rubber Blackbond IB1419A 22 Rubber with Tissue Carrier IB1690A 23 Rubber with SWV Carrier IB1950 23 Optically Clear IB2104 24 Rubber/Acrylic IB2125A 24 Acrylic Blackbond IB2408 24 Heat Seal Film/Acrylic PSA IB2711A 25 Acrylic with Scrim Carrier IB6205W50 25 IB6280W50 25 Prefinished IB1182PS, IB1190APS 26 SB1786 27

page

MACfilm® 28 Rubber, Free Films, Single Liner IF1092A, IF1093A-80 29

Acrylic, Free Films, Single Liner IF20V2, IF2012A, IF2013A 30 IF2013AP2 IF2015A, IF2071 31 IF2092, IF2095 32

Acrylic, Free Films, Double Liner IF2043B, IF3041, IF3041TF 33

MACmount® 34 Rubber, Double-coated Foams, Single Liner IM1705A, IM1800A, IM1801A 35 IM1810A, IM1830A, IM1900A 36 IM1930A, IM1940A 37

Acrylic, Double-coated Foams, Single Liner IM2901, IM29078N, IM2908-80 38 IM2920, IM2940 39

GS Series 40 High-Strength Adhesive Tapes GS2004, GS21003 41 GS1001, GS1013, GS1039, GS1019 42 GS1004, GS1007, GS2906 43

Phenolic Tapes 44 Phenolic IF4020A, IF4023A 45

Safety Grit 46 IC6187 47

Application Ideas Building & Construction 48 Appliance 49 RV & Marine 50 Automotive 51

Adhesive Recommendations Foam Fabrication 52

Basket of 12 MACtac® Products You Should Know 53

Conversions & Fractions Charts 54-56

Credit Application 57-58

Additional Information 59

Packaging & Labeling 60-61

pg. 3

Specialty Products

email: [email protected]. MACtac.com/technical

Corporate Overview

MACtac® Specialty Products has been a trusted source of pressure sensitive adhesive materials for over 50 years. Our engineered adhesive solutions are a key component in mounting, laminating, bonding, and fastening for converters and OEM’s in a wide range of markets and applications. Markets served include but are not limited to appliance, automotive, gasket fabrication, alternative energy, construction, and aerospace. Our expertise in adhesive coating and our state-of-the-art technology expands functionality, inspires new product designs, and delivers speed to solutions – cost effectively. We offer a wide range of adhesive single- and double-coated films and foams to fit in a variety of applications.

•State-of-the-artadhesivecoatingfacilities

•Dedicatedresearchanddevelopment

•Dedicatedsalesandtechnicalsupport

•Customizablesolutions

MACtac’s core competency is pressure sensitive adhesive coating and we look forward to providing you the adhesive solution that best fits your need. Please use this book as a reference for choosing the correct product for your application. If you have any questions or if there is a specific solution you are looking for please contactMACtacSalesat800-328-2619.

Thank you,

Justin Kalvitz General Manager Specialty & Retail

Customer Service 800-321-0011

Fax 888-821-8834

Email [email protected]

Aerospace

Appliance

Automotive/Recreation

Construction

Electronics

Glasses

General Manufacturing

Plate Mounting

UL Listed

pg.4

Phone: 1-800-328-2619

Specialty Products TechnicalAdhesiveConstructions

Single-CoatedSingle-coated adhesive products consist of a flexible face stock material that is coated on one side with a pressure sensitive adhesive which is used to bond the

product to a substrate. The adhesive is typically protected by a release liner which is removed and discarded at the time of installation. On a single-coated adhesive product the face stock typically performs a unique function. A good example is the MACtac® Black Grit safety products.

Double-CoatedDouble-coated adhesive products consist of a fairly thin, flexible carrier membrane that is coated on both sides with a pressure sensitive adhesive.

Double-coated adhesives are designed to bond two substrates either similar or dissimilar in nature together. Double-coated adhesive constructions are highly customizable to meet end user requirements. The two adhesive layers can be the same or different adhesives. The proper selection will provide the correct

gap filling and will ensure the optimum adhesive contact with each substrate. MACtac double-coated adhesive products are ideal for gasket bonding, insulation materials, bonding electronic components, attaching molding, extruded plastic parts and more.

FreeFilmFree film adhesive products consist of a layer of pressure sensitive adhesive on a release liner without a carrier membrane. The lack of a carrier allows the

adhesive to be more extensible and conformable. Free film adhesives are designed to bond two substrates either similar or dissimilar in nature together. MACtac free film adhesive products are ideal for mounting nameplates, second surface printed signs or labels, and other decorative substrates.

AdhesiveCarrier

AdhesiveLiner

Face StockAdhesive

Liner

Adhesive

Liner

pg. 5

Specialty Products


TechnicalCarrierMembranes

Acarriermembranecanbeanyrelativelythin,flexiblematerialsuchaspaper,filmorfoam.Theterm“carrier”usuallyreferstomaterialthathasbeencoatedonbothsideswithadhesive.Acarrier’sprimaryfunctionistocarrytheadhesivebutacarrieralsoprovidesreinforcingstrength,gapfillinganddimensionalstabilitytotheproduct.

Paper CarriersPaper carrier membranes are composed of cellulose fibers and differ from one another by weight, degree of chemical treatment, thickness and color. Based on the thickness they provide paper carriers are a sound economical choice.

FilmCarriersFilm carrier membranes are composed of various forms of thin plastic such as polyester, polypropylene, polyethylene, and polyvinylchloride. The films differ by thickness, chemical resistance, barrier properties, tensile strength, temperature resistance, and color. An added benefit of a film carrier is it is water resistant.

Polyester(PET)Films: PET film carriers are clear films that offer high tensile strength and can be used with most adhesive technologies. PET films also provide good barrier properties to most migratory chemicals.

Polypropylene(PP)Films: PP film carriers are available in oriented and non-oriented versions. Most manufactures use clear PP films but white and colored films are also available. Both oriented and non-oriented films are water resistant and neither provides sufficient barrier properties for migratory chemicals.

Polyethylene(PE)Films: Polyethylene (PE) Films: PE films are available in oriented and non-oriented versions. Most manufactures use clear PE films but white and colored films are also available. Both oriented and non-oriented films are water resistant and neither provides sufficient barrier properties for migratory chemicals. PE films are similar to PP films but are more easily stretched and relatively inexpensive.

Polyvinylchloride(PVC)Films:PVC films are available in hard (semi-rigid) and soft formulations. Hard PVC is less conformable and has a higher tensile strength so it is not right for all applications. However, it is also less plasticized and offers better adhesive compatibility. Soft PVC is more conformable but because of the plasticizers prevents the use of certain adhesives. PVC films are available in clear, white, and colored versions.

FoamCarriersFoam carrier membranes are composed of various forms of plastic such as polyethylene, polyvinylchloride, urethane, and neoprene. Foam carriers are designed to provide the necessary thickness to fill a gap between two surfaces that are bonded. Foams are conformable and permit surface contact between uneven or irregular surfaces and they also provide insulating and shock absorbing properties.

Polyethylene(PE)Foam:PE foam is cross-linked, closed cell foam widely used by manufactures to produce double-coated mounting foams and single-coated tapes for a variety of industrial applications.

Polyvinylchloride(PVC)Foam:PVC foam is used by manufactures to produce single- and double-coated mounting tapes. PVC foams offer a combination of softness and strength and is a good fit for certain applications.

UrethaneFoam:Urethane foams are available in ester and ether form. They are available in many thicknesses and densities and designed to work for specific applications.

NeopreneFoam:Neoprene foams are used to produce double-coated mounting foams for special applications. These foams are not used extensively but are available. Neoprene foams are strong and provide excellent chemical resistance.

OtherCarriersScrim: Scrim woven materials consist of threads of material that are woven into a variety of patterns. The patterns that are formed can be squares, rectangles, diamonds and other geometric shapes. The threads are typically spaced to form a wide open weave. Scrims primary purpose is to provide reinforcing strength to the adhesive.

pg.6

Phone: 1-800-328-2619

Specialty Products TechnicalLinerCategories

DensifiedKraftPaperLinersDensified kraft liners are semi-bleached papers that have been super calendered to produce a high-density sheet with relatively low porosity. Because of their low porosity, these papers can be coated with silicone release on either or both sides. They are commonly referred to as “SCK,” which stands for Super Calendered Kraft.

60#SCK:This liner is the “workhorse” in double-coated adhesive products. It has a balanced combination of good economy and enough thickness to allow most kiss cutting, and good tensile strength for good web processing.

80#SCK:This liner is used when even more additional liner thickness is required. It will provide easier die-cutting processes and easier removal during assembly since it is thicker and stiffer.

PolycoatedKraftPaperLinersThis family of liners combines the properties of paper and polyethylene to produce a dimensionally stable product that provides excellent thickness and easy release characteristics with an improved level of moisture stability.

72#PCK:This white polycoated liner is capable of being coated with release on both sides and, therefore, can be used in single-liner, self-wound tape constructions. It provides good moisture stability and is approximately 6.0 mils thick.

83#PCK:This is a brown, unbleached, polycoated paper. It can be release coated on both sides for use in self-wound tapes. However, it can also be coated on one side only, if required. It has a thickness of approximately 6.4 mils..

90#PCK:This polycoated release liner is considered a premium product for use on sheeted products because of its dimensional stability, white color, layflat characteristics and easy release properties. It can be coated with release on only one side, which precludes its use in self-wound constructions. Its moisture stability is apparent in processes that require subsequent drying, such as in the screen printing industry. It is approximately 6.9 mils thick.

12ptBoard:Polycoated, unbleached (brown) 12pt kraft board liners are available release coated on both sides for use in double-sided adhesive constructions. They are used primarily for their thickness and stiffness. In the gasketing industry, the thicker liner permits easier and faster steel rule die set-up. Once the gasket is cut, the stiffness of the liner allows the converter to provide several gaskets on a sheet that can be easily handled by the end user.

pg. 7

Specialty Products


TechnicalLinerCategories

CoatedKraftLinersCoated Kraft liners are bleached papers with a clay coating on one side. The clay coating is necessary to produce a good hold out from the silicone release since these papers are more porous than the densified Kraft papers.

80#CCK:This liner is the predominant choice for most sheeted products. Its thickness is approximately 4.8 mils. It can be “kiss cut” in the traditional manner and cut against as done in computer graphics.

60#CCK:This liner can be used when a more economical liner is required. Lighter weight and lower thickness of 3.6 mil has good “kiss cutting” properties. This liner has high tensile strength for good web processing.

FilmLinersFilm liners provide excellent moisture resistance and typically lend themselves to producing a super smooth adhesive.

Polyester(PET): PET liners are very stable, providing high tensile and tear strength while maintaining total clarity. PET liners can be easily handled in both the coating and converting processes without shrinking or expanding. Polyester liners can be coated on both sides and are moisture resistant.

LowDensityPolyethylene(LDPE): Low density film has excellent extensibility producing a very conformable liner. It has potential for stretching when exposed to stress of high temperature but is beneficial when the bonded part with liner in place needs to be formed. It is supplied as clear or opaque and is moisture resistant.

High DensityPolyethylene(HDPE):High density film is much stronger and less elastic than low density but is less conformable. Its higher density tolerates higher temperatures which permits processing through coater ovens without dramatically stretching the film. HDPE films are water resistant.

pg. 8

Phone: 1-800-328-2619

Specialty Products TestingMethods

The four tests that most accurately gauge PSA product performance in standard applications are:

PeelAdhesionThis test measures the force required to remove a pressure sensitive tape from a substrate at a controlled angle, standard rate and condition.

• Peelangle (Std.is180,90degrees)• Substrate (Std.isstainlesssteel)• Peelrate (Std.is12in./min)• Residencetime (30min.,24hr.,etc.)• Testenvironment (Std.is72°F/50%R.H.)• Bondingprocedure (Mustbedefined)• Sampledimensions (Std.is1”wide)Peel adhesion is normally expressed in pounds per inch width

(lbs./inch).

ShearAdhesionAlso referred to as holding power or creep resistance, this test measures the ability of a tape to resist the static forcesappliedinthesameplaneasthefaceorcarrier.Resultsareusuallyexpressedintimerequiredforagivenweight to cause a given amount of tape to come loose from a vertical panel.

• Substrate (Std.isstainlesssteel)• Bondingprocedure (Mustbedefined)• Sampledimension (Dimensionsofbondedarea)• Testenvironment (Temperature/humidity)• Sheardirection (Vertical/horizontal)Shear is typically expressed in “hours to fail.”

Stainless SteelTest Panel

Adhesive Sample Supported with 2.0 mil PET Backing

Adhesive Surface in Contact with Test Panel

Force

Adhesive TapeSupported by2.0 mil PET

Standard WeightStainless SteelTest Panel

pg.9

Specialty Products


TestingMethods

Quick TackThis refers to the properties that allow a PSA to adhere to a surface under very light pressure. It is determined by the ability of the adhesive to quickly wet the surface contacted.

• Type tack test a. Loop Tack b.RollingBall c. Polyken Probe d. Finger Tack• Substrate (Std.isstainlesssteel)

ReleaseA measure of the force per unit width required to break the bond between the PSA and the protective liner, this test incorporates rate of separation, angle of separation and width of the sample. With this test, it is important to consider the separation rate as speeds may not be consistent between testers.

• Rateofseparation • Angleofseparation • Widthofsample

MACtac® Method: MACtac relies on the Scott ReleaseTest. It specifies a separation rate of 32 ft./min.,a 180 degree angle and a 2” wide sample. The force of separation is expressed as “grams per 2” width.”Commonspeedsinclude32ft./min.,12in./min.and300in./min.Varyingthespeedwillproducedifferentresults.

OtherTestMethodsAdditional testing methods are also used to measure:

• TensileStrength• Elongation• TearStrength• Thickness• Shrinkage• Weatherometer• QUV

Adhesive TapeSupported by2.0 mil PET

Adhesive Surfacein Contact with Test Area

Force

pg.10

Phone: 1-800-328-2619

MACbond®

MACbonddouble-coatedfilmtapes– Engineered for the most demanding bonding or laminating applications, these tapes feature general purpose and high-performance rubber-based adhesives or high-performance acrylic adhesives on polyester, polypropylene or the popular Blackbond™ carrier. An enhanced product line including a scrim carrier is also available.

•Idealforalternativeenergy,transportation,electronics, construction,automotiveandappliancemarkets.

•Appliedincushioning,sealing,stiffening,sounddampening and gaskets

•Speedsassemblyandlowersmanufacturingcosts

•Replacesmechanicalfastenersandliquidadhesives

•Bondstoawiderange of surfaces

pg.11

MACbond® Rubber, Double-coated Films, Single Liner


IB1111A Consists of a thin polyester film carrier coated on both sides with an aggressive, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft release liner.

Used extensively for the mounting and bonding of flexible magnetic materials. It can also be used to bond a variety of substrates including those that are relatively rough in surface texture. This product construction has been specially designed with a tighter than normal release in order to permit processing small cut parts without the liner removing from the adhesive prematurely.

Performance TestTypical Values

Testing MethodUnwind Liner

Quick Tack lbs./sq. in. - Stainless Steel 12.5 11.0 PSTC-16

Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 9.5 9.0 PSTC - 101

Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107

Thickness - Carrier & Adhesive .005

Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)

Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 2.0 mil / 2.0 mil 0.5 mil PET 60# White SCK -

MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.34 10.2” 54” x 750’ 6” x 30’

AdhesiveFilm

AdhesiveSCK Liner

IB1161 IB1161 consists of a thin polyester film coated on both sides with an aggressive, general-purpose, rubber- based pressure sensitive adhesive. The product is supplied self-wound on 60# Semi-Bleached, Densified-Kraft (SCK) release liner. IB1161 provides an economical solution exhibiting moderate adhesion and shear resistance. IB1161 is intended for use as an assembly aid for bonding foam, felt, cloth, paper, primed wood, metal and many low or unplasticized plastics in gasket, seal, trim & other applications.The½milPETfilmcarrierprovidesgoodstrength/stabilityforoptimumhandlingthroughvarious slitting, laminating, die-cutting processes.







Temperature Application: Above 40°F (4°C) for best results. End Use: -50° to 140°F (-29° to 60°C)


MSI Wt/MSI Roll OD Master Roll Sample Roll540 na na 60” x 750’ 6” x 30’

AdhesiveFilm

AdhesiveSCK Liner

IB1101AA polyester film coated on both sides with a high performance, rubber based pressure sensitive adhesive. The product is supplied self-wound on a polycoated natural kraft release liner.

IB1101A exhibits outstanding shear resistance and high adhesion. The extra thick (1.0 mil) polyester carrier provides added strength and stability for optimum processing and handling.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.8 mil / 1.8 mil 1.0 mil PET 83# Brown PCK -


AdhesiveFilm

AdhesivePCK Liner

pg.12

Phone: 1-800-328-2619


pg.12

IB1175AL12

A thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a 12 pt. polycoated two side, natural kraft release liner.

Designed for general purpose bonding applications such as in the gasket, seal, and trim markets Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance. The polyester carrier provides dimensional stability and superior die cutting properties.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.8 mil / 1.2 mil 0.5 PET 12pt Board -

MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.60 10.0” 54” x 750’ Custom

AdhesiveFilm

Adhesive

12 pt Board

Liner

Consists of a thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. Supplied self-wound on a densified, semi-bleached kraft liner.

Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance. The polyester carrier provides dimensional stability and superior die cutting properties.










IB1175AER

AdhesiveFilm

AdhesiveSCK Liner

IB1175AERW60 60”Wide - Consists of a thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.











AdhesiveFilm

AdhesiveSCK Liner

Contact Sales for minimums and lead time.

pg.13



IB1178A A thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.

Designed for general purpose bonding applications to relatively smooth surfaces. Typically, it can be used for bonding to paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance. The polyester carrier provides dimensional stability and superior die cutting properties.










AdhesiveFilm

AdhesiveSCK Liner

IB1178AW60 60”Wide - A thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.

Designed for general purpose bonding applications to relatively smooth surfaces. Typically, it can be used for bonding to paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance. The polyester carrier provides dimensional stability and superior die cutting properties.










AdhesiveFilm

AdhesiveSCK Liner

IB1182 A thin polyester film coated on both sides with a general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a 60# densified, semi-bleached kraft liner.

Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance and can be used in many applications as an aid to assembly. The polyester carrier provides dimensional stability and superior die cutting properties.










AdhesiveFilm

AdhesiveSCK Liner

pg.14

Phone: 1-800-328-2619


IB1182W60 60”Wide - A thin polyester film coated on both sides with a general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a 60# densified, semi-bleached kraft liner.

Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance and can be used in many applications as an aid to assembly. The polyester carrier provides dimensional stability and superior die cutting properties. 60” Version of IB1182.










AdhesiveFilm

AdhesiveSCK Liner

IB1183W60 60”Wide - A thin polyester film coated on both sides with a general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on an 80# densified, semi-bleached kraft liner.











AdhesiveFilm

AdhesiveSCK Liner

IB1183 A thin polyester film coated on both sides with a general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on an 80# densified, semi-bleached kraft liner.











AdhesiveFilm

AdhesiveSCK Liner

pg.15



IB1184W60 A thin polyester film coated on both sides with a heavy coating of an aggressive, high performance, rubber based pressure sensitive adhesive. Self-wound on an 80# densified, semi-bleached kraft liner.

Designed for the more demanding bonding applications encountered in the gasket, seal and trim lamination markets where high tack and high ultimate bond strength are required. The heavy coating of adhesive aids in bonding rough or irregular surfaces. The polyester carrier provides dimensional stability and superior die cutting properties.










AdhesiveFilm

AdhesiveSCK Liner

IB1185L12 A thin polyester film coated on both sides with a general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a 12 pt. polycoated two side, natural kraft release liner.

Designed for general purpose bonding applications such as in the gasket, seal, and trim lamination markets. It can be used in many applications as an aid to assembly. The polyester carrier provides dimensional stability and superior die cutting properties. The added thickness of the 12 pt. liner contributes to easy die cutting, excellent layflat of the cut sheets and quick, easy removal of the die cut parts.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.5 mil / 1.5 mil 0.5 mil PET 12pt Board -


AdhesiveFilm

Adhesive

12 pt Board

Liner

IB1188 DiverseCoatWeights - A thin polyester film coated on both sides with a rubber based pressure sensitive adhesive. One side has been specially designed to provide maximum adhesion to foams, fabrics and other highly textured surfaces. The product is supplied self-wound on a 80# densified, semi-bleached kraft liner.

Designed for bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates.Theresultingproductsaresuitableforabroadrangeofapplicationsinthegasket,sound/thermal insulation, appliance and automotive markets. The polyester carrier provides dimensional stability and superior die cutting properties.










AdhesiveFilm

AdhesiveSCK Liner

IB1190A A thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.










MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.30 9.5 54” x 750’ 6” x 30’

AdhesiveFilm

AdhesiveSCK Liner

IB1190AW60 60”Wide - A thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.











IB1190AP2 consists of a thin polyester film coated on both sides with an aggressive, general-purpose, rubber-based adhesive. The product is supplied at 54” width in self-wound form on a C2S 2 mil PET liner.

IB1190AP2 was designed for general purpose bonding applications such as in the gasket, seal and trim markets. IB1190AP2 is typically used for bonding to foams, felts, cloths, primed wood, paper, metal and manylow/unplasticizedplastics.Thepolyestercarrierprovidesdimensionalstabilityandsuperiordiecutting properties.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.8 mil / 1.2 mil 0.5 mil PET 2 mil PET -

MSI Wt/MSI Roll OD Master Roll Sample Roll486 na na 54” x 750’ Custom

AdhesiveFilm

AdhesiveSCK Liner

AdhesiveFilm

Adhesive

2.0 Mil PET Liner

AdhesiveFilm

AdhesiveSCK Liner

IB1190AP2

pg.16

Phone:1-800-328-2619

MACbond® Rubber,Double-coatedFilms,SingleLiner


pg.17

MACbond® Rubber,Double-coatedFilms,SingleLiner


IB1200A A thin unoriented, polypropylene film coated on both sides with a high performance, rubber based pressure sensitive adhesive. The adhesive is protected by a release treated, 60# densified kraft liner.

IB1200A demonstrates unusually high tack and peel adhesion without sacrificing shear resistance. The heavy coating weight of adhesive provides excellent bonds to both smooth and irregular surfaces. The unoriented carrier membrane permits good conformability.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 2.7 mil / 2.7 mil 0.9 mil PP 60# White SCK -


AdhesiveFilm

AdhesiveSCK Liner

IB1271 IB1271consistsofa1.0milpolyesterfilmcoatedoneachsidewithacustom-formulated,rubber-basedpressure-sensitive adhesive. It is specially designed for adhesion to low-surface-energy substrates, high shear strength and clean removability from many surfaces. The product is supplied in self-wound form on 60# semibleached, densified-kraft release liner.

Engineered as an aggressive-removable laminate. The unique adhesive adheres to a variety of substrates while the high shear and 1.0 mil PET carrier aid in removability. This engineered laminate is not recommended for removal from high-surface-energy materials such as glass. MACtac recommends testing against specific end-use application requirements to confirm acceptable removability.







Temperature Application: Above 40°F (4°C) for best results. End Use: 0°F to 150°F (-18°C to 66°C)

Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.0 mil /1.0 mil 1.0 mil PET 60# White SCK -


AdhesiveFilm

AdhesiveSCK Liner

IB1271W60 IB1271W60consistsofa1.0milpolyesterfilmcoatedoneachsidewithacustom-formulated,rubber-based pressure-sensitive adhesive. It is specially designed for adhesion to low-surface-energy substrates, high shear strength and clean removability from many surfaces. The product is supplied in self-wound form on 60# semibleached, densified-kraft release liner.

Engineered as an aggressive-removable laminate. The unique adhesive adheres to a variety of substrates while the high shear and 1.0 mil PET carrier aid in removability. This engineered laminate is not recommended for removal from high-surface-energy materials such as glass. MACtac recommends testing against specific end-use application requirements to confirm acceptable removability.







Temperature Application: Above 40°F (4°C) for best results. End Use: 0°F to 150°F (-18°C to 66°C)

Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.0 mil /1.0 mil 1.0 mil PET 60# White SCK -


AdhesiveFilm

AdhesiveSCK Liner

IB2100 A thin polyester film coated on both sides with a high performance acrylic based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.

Typically used for industrial bonding applications where outstanding adhesion, high shear and good solvent resistance are required. The acrylic adhesive offers good clarity and has excellent resistance to U.V. light exposure. The polyester carrier provides excellent dimensional stability and die cutting properties.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.4 mil / 2.4 mil 0.5 mil PET 60# White SCK -


AdhesiveFilm

AdhesiveSCK Liner

IB2101 A thin polyester film coated on both sides with a high performance acrylic based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.

Is typically used for industrial bonding applications where good adhesion, high shear and good solvent resistance are required. IB2101 is best suited for bonding relatively smooth surfaces and similar applications requiring a thin reinforced adhesive film. The acrylic adhesive offers good clarity and has excellent resistance to U.V. light exposure. The polyester carrier provides excellent dimensional stability and die cutting properties.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 1.1 mil / 1.1mil 0.5 mil PET 60# White SCK -


AdhesiveFilm

AdhesiveSCK Liner

IB2130 A thin polyester film coated on both sides with a high tack, modifiedacrylicpressure sensitive adhesive. Theproductissuppliedself-woundona74#polycoatedwhitekraftliner.

The unique acrylic adhesive bonds to a wide range of materials, including most plastics and foams. IB2130 provides the temperature resistance required by many automotive and appliance applications without sacrificing peel and tack adhesion. The polyester carrier provides excellent dimensional stability and die cutting properties.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerModified Acrylic 1.8 mil / 1.5 mil 0.5 mil PET 72# White PCK -


AdhesiveFilm

AdhesivePCK Liner

pg.18

Phone:1-800-328-2619

MACbond® Acrylic,Double-coatedFilms,SingleLiner

IB2133

IB-2132 consists of a thin polyester film coated on both sides with a high tack, modified acrylic pressure sensitive adhesive. The product is supplied self-wound on an 80# densified kraft liner.

The unique acrylic adhesive bonds to a wide range of materials, including most plastics and foams. IB-2132 provides the temperature resistance required by many automotive and appliance applications without sacrificing peel and tack adhesion. The polyester carrier provides excellent dimensional stability and die cutting properties.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerModified Acrylic 1.9 mil / 1.6 mil 0.5 mil PET 80# White SCK -


IB2133 consists of a thin polyester film coated on both sides with a high-tack, modified-acrylic, pressure sensitiveadhesive.Theproductissuppliedinself-woundformona72#WhitePolycoatedKraftliner.

The unique acrylic adhesive of IB2133 bonds to a wide range of materials, including most solid plastics and foams. The unique acrylic adhesive used in IB2133 also provides the temperature resistance required in many automotive and appliance applications without sacrificing immediate & ultimate adhesion. The polyester carrier provides excellent dimensional stability and die cutting properties.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerModified Acrylic 2.8 mil /2.8 mil 0.5 mil PET 74# White PCK -


AdhesiveFilm

AdhesivePCK Liner

pg.19



AdhesiveFilm

AdhesiveSCK Liner

IB2132



pg. 20

Phone:1-800-328-2619


IB2180N A thin polyester film coated on both sides with a high tack, modifiedacrylic pressure sensitive adhesive. Theproductissuppliedself-woundona74#polycoatedwhitekraftreleaseliner.

Provides aggressive tack and peel for quick bonding and long term adhesion. The unique acrylic adhesive bonds to a wide variety of materials with exceptional adhesion to low energy surfaces such as polypropylene and polyethylene. The polyester carrier provides excellent dimensional stability and die cutting properties.










AdhesiveFilm

AdhesiveSCK Liner

IB2154

A 4.0 mil Black HDPE film coated on both sides with high-tack, modified-acrylic pressure sensitive adhesive(PSA).Theproductissuppliedself-woundonableached,74#PE-coatedKraftreleaseliner.

The modified-acrylic adhesive bonds well to range of materials, including many plastics. IB2154 provides the temperature resistance required in many automotive, appliance and other applications without sacrificing adhesion. IB2154 was originally developed for use in exterior automotive mirror-mounting applications.






ThicknessCarrier plus adhesiveLiner

.0080

.0055




AdhesiveBlack Paper

AdhesiveSCK Liner


pg.21

MACbond®


Acrylic,Double-coatedFilms,DoubleLiner

IB2107 A thin polyester film coated on both sides with a high performance acrylic based pressure sensitive adhesive. The product is supplied with two white kraft release liners for ease of handling and processing in a sheet form.









Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.4 mil / 2.4 mil 0.5 mil PET 80# White CCK 80# White CCK

MSI Wt/MSI Roll OD Master Roll Sample Sheet486 0.52 13.0” 54” x 750’ 8-1/2” x 11”

CCK LinerAdhesive

FilmAdhesiveCCK Liner

pg. 22

Phone: 1-800-328-2619

MACbond® Specialty

IB1250TR Permanent/Removable A 1.0 mil carrier film coated on both sides with a pressure sensitive adhesive. The “unwind side” is an aggressive, general purpose, permanent adhesive. The “liner side” utilizes a low adhesion, removable formulation. An 80# release coated, densified kraft liner protects the adhesive.

Designed for laminating permanently to the initial substrate. The second or final bond would provide removable adhesion from most substrates. This construction permits the production of removable or repositionable products such as gaskets, protective pads, and other temporarily bonded items.

Note:“Removability”isdependentonapplicationandsurfaceconditions.Usermusttestforsuitabilityintheir specific application.




Peel Adhesion, lbs./in. Stainless Steel - 30 minutes Stainless Steel - 24 hours

8.08.0

0.41.0

PSTC - 101




Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber / Rem. Acrylic 1.4 mil / 0.7 mil 1.0 Clear PP 80# White SCK -


AdhesiveFilm

AdhesiveSCK Liner

IB1419A Rubber Blackbond A latex impregnated black paper that is coated on each side with a high performance, rubber based pressure sensitive adhesive. The product is supplied with a polycoated white kraft liner on one side and a polycoated white kraft liner on the other.

Used extensively to bond plastic and metal faceplates, nameplates, logos, and other components in the home electronics industry. The black paper carrier provides the opaque block-out characteristic required in many applications. The aggressive adhesive insures quick reliable bonding during assembly.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.5 mil / 1.5 mil Blackbond 90# White PCK 90# White PCK


LinerAdhesive

Black PaperAdhesivePCK Liner

IB1950

pg. 23

MACbond®


Specialty

IB1690AR Rubber with Tissue Carrier A light weight paper stock coated on each side with an aggressive, general purpose, rubber based pressure sensitive adhesive. Each side is protected by a release coated white kraft liner.

General purpose bonding system that can be easily handled in sheet form because of the two protective release liners. The adhesive bonds to a wide variety of substrates.

Performance Test Typical Values Testing Method

Quick Tack lbs./sq. in. - Stainless Steel 5.0** PSTC-16

Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 7.0** PSTC - 101

Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107



Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.2 mil / 1.2 mil White Fiber Stock 80# White CCK 80# White CCK

MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.54 12..5” 54” x 750’ 6” x 30’

**Theadhesionfrequentlyexceedsthestrengthofthepaperandresultsindelaminationintherangeof5-7lbs

LinerAdhesive

PaperstockAdhesiveCCK Liner

Rubber with PVC Carrier IB-1950 consists of a thin, white-opaque PVC film coated on both sides with an aggressive, rubber-based pressure sensitive adhesive. The product is supplied in self-wound form on a semi-bleached, 50# densified kraft paper release liner.

IB-1950 was originally designed to fasten carpet, area rugs and other soft floor coverings to a variety of hard interior and exterior flooring surfaces. IB-1950 may also be used in general-purpose gasket, seal,trimandotherbonding/die-cuttingapplications.Therubber-basedadhesivesystemworkswellwith foams, felts, cloths, primed wood, paper, metal, and plastics. The white PVC film carrier provides excellent “block-out” opacity, dimensional stability, tensile strength and die-cutting properties.





Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F na na PSTC - 107



Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner

Rubber 0.8 mil / 0.8 mil3.25 mil Soft White

Vinyl3.2 mil SCK -

MSI Wt/MSI Roll OD Master Roll Sample Sheet486 na na 54” x 750’ Custom

AdhesiveFilm

AdhesiveSCK Liner


pg.24

Phone:1-800-328-2619

IB2408

Acrylic Blackbond A latex impregnated black paper that is coated on each side with a high performance, acrylic pressure sensitive adhesive. The product is supplied with a polycoated white kraft liner on one side and a polycoated white kraft liner on the other.

Designed to bond most plastic and metal faceplates, nameplates, logos and other components in the home electronic industry. The black paper carrier provides the opaque block-out characteristic required in many applications. The acrylic adhesive offers improved performance at elevated temperatures.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.4 mil / 2.4 mil Blackbond 90# White SCK 90# White SCK


LinerAdhesive

Black PaperAdhesivePCK Liner

MACbond® Specialty

IB2104 Optically Clear A thin polyester film coated on both sides with a high performance acrylic based pressure sensitive adhesive. The product is supplied self-wound on a2.0milopticallyclearPETLiner.Is typically used for industrial bonding applications where outstanding adhesion, high shear and good solvent resistance are required. The acrylic adhesive offers good clarity and has excellent resistance to U.V. light exposure. The polyester carrier provides excellent dimensional stability and die cutting properties.









Acrylic 1.75 mil / 1.75 mil 1.0 mil PET 2.0 mil Optically Clear PET Liner -

MSI Wt/MSI Roll OD Master Roll Sample Sheet259.2 na na 51” x 400’ 8-1/2” x 11”

AdhesiveFilm

Adhesive

2.0 Mil PET Liner

IB2125A Rubber/Acrylic A thin polyester film coated on one side with an aggressive, modified-acrylic pressure- sensitive adhesive and on the opposite side with high-performance, rubber-resin pressure-sensitive adhesive. IB2125A utilizes an 80# SCK release liner that provides a good combination of lamination, die-cutting and end-use application performance.

The “unwind side” modified-acrylic PSA provides excellent adhesion and compatibility with a wide range of foam, sponge, rubber, cork and other gasket materials. The “liner side” rubber-based PSA provides excellent adhesive performance on many end-use substrates with exposure to demanding application conditions. The polyester carrier provides dimensional stability and superior die cutting properties.








Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic/Rubber 1.5 mil / 1.5 mil 0.5 mil PET 80# White SCK -


AdhesiveFilm

AdhesiveSCK Liner


pg. 25


MACbond® Specialty

IB2711A Heat Seal Film / Acrylic PSA IB-2711Aconsistsofaheatsensitivefilmcoatedwithablueacrylic adhesive and a paper liner. It offers moderate tack and adhesion properties and high cohesive strength. It has been especially designed for the fastening and protection of lenses during the processing stages in the optical industry.



Quick Tack lbs./sq. in. - Stainless Steel 2.0 PSTC-16

Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 2.0 PSTC - 101





Blue Acrylic 1.29 mil 4.0 mil Heat Sensitive LDPE 40# SCK -


IB6280W50 Acrylic with Scrim Carrier A thin polymeric scrim reinforcement combined with high-tack, modified-acrylic adhesives coatings. Supplied self-wound with 80# densified, semi-bleached kraft paper liner.

The modified-acrylic, pressure-sensitive adhesive used bonds to a wide range of gasket materials, includingmostsolidandfoamedplastics.Thescrimreinforcementprovidesexcellentadhesive/composite reinforcement, dimensional stability and conformability while maintaining maximum adhesion properties. Note: IB6205, a similar product with 5.0 mil Blue HDPE liner, is also available in 50”-wide, self-wound rolls.






Thickness - Carrier & Adhesive .006Temperature Application: Above 50°F (10°C) for best results. End Use: -40° to 302°F (-40° to 150°C)** ** MACbond IB6280 tested as free-film construction to UL 969

Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.5 mil / 2.5 mil Scrim 80# White SCK -


AdhesiveScrim

AdhesiveSCK Liner

IB6205W50

Acrylic with Scrim Carrier A thin polymeric scrim reinforcement combined with high-tack, modified-acrylic adhesives coatings. Supplied self-wound with 5 mil Blue HDPE release liner which providesimprovedtearandmoisture/humidityresistanceoversimilarproductIB6280(80#BleachedSCK liner).

The modified-acrylic, pressure-sensitive adhesive bonds to a wide range of gasket materials, including mostsolidandfoamedplastics.Thescrimreinforcementused,providesexcellentadhesive/compositereinforcement, dimensional stability and conformability while maintaining maximum adhesion properties.







Temperature Application: Above 50°F (10°C) for best results. End Use: -40° to 302°F

Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.5 mil / 2.5 mil Scrim 5.0 mil Blue HDPE -

MSI Wt/MSI Roll OD Master Roll Sample Roll450 9.5” 50” x 500’ Custom

AdhesiveScrim

Adhesive

5.0 Mil HDPE Liner

4.0 MilLDPE

Adhesive

SCK Liner


pg.26

Phone: 1-800-328-2619

MACbond® Prefinished

IB1190APS A thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.










MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.30 9.5 54” x 750’ 6” x 30’

AdhesiveFilm

AdhesiveSCK Liner

IB1182PS A thin polyester film coated on both sides with a general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a 60# densified, semi-bleached kraft liner.











AdhesiveFilm

AdhesiveSCK Liner

pg. 27



SB1786 A thin polyester film coated on both sides with a high performance acrylic based pressure sensitive adhesive. The product is supplied with two white kraft release liners for ease of handling and processing in a sheet form.









Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.4 mil / 2.4 mil 0.5 mil PET 80# White SCK 80# White SCK

MSI Wt/MSI Roll OD Sheet Size Sample Sheetna 0.52 na 18” x 22”, 100/ctn 18” x 22”

SCK LinerAdhesive

FilmAdhesiveSCK Liner

Slitting Short Rolls Sheeting Pattern CoatingSize $/MSI Setup/Release Size $/MSI Setup/Release Size $/MSI Setup/Re-

lease- 10 MMSI minimum order

- $50 set-up charge

- $0.15/MSI

- $200 pattern bar charge

>6” $0.02 - Less than 750’ $0.06 $25 150+ sq inch with minimum 10” dimension

$0.15 -

>2-6” $0.06 - Less than 300’ $0.12 $25

>1-2” $0.10 $25 Less than 150’ $0.17 $25 Smaller or dutch cut sheets

$0.30 $50

5/8” - 1” $0.15 $25 Custom pallets/crates (for custom sheets greater than 800 sq inches)

$50.00/pallet

-

<5/8”(3/8”-1/2”)

The listed web width is the minimum purchase however, please note the following for these narrow rolls:60” wide web material will yield 54” of material available to ship54” wide web material will yield 48” of material available to ship50” wide web material will yield 44” of material available to shipThe additional charges will be the same as 5/8”-1” for these sizes.Shipments of material with widths less than 5/8” may be - 25% of original quantity requested.

MACbondAdditionalCharges

pg. 28

Phone:1-800-328-2619

MACfilm®

MACfilmtransferfilms – These free films are engineered to assure smooth, low-profile bonding. The moisture-resistant polycoated release liner is curl resistant and assures complete edge-to-edge bonding of laminated and die-cut parts, even in high humidity.

•Idealfornameplates,membraneswitchesassembly,moldingandtrimconstruction

•Unsupportedrubberandacrylicfreefilms

•Modifiedacrylicforhigh-tack,high-temperatureperformance

•Moisture stable release liners

•Availablein1.0milto5.0milthickness

•Bondstoawidevarietyofsubstratesincludinglow-surfaceenergymaterialssuchaspowder-coatedmetalandplastics

pg.29

MACfilm® Rubber,Double-coatedFilms,SingleLiner


IF1093A-80

A 2.0 mil thick film of high performance, rubber based pressure sensitive adhesive. The adhesive is protected by a two side release treated, 80# densified kraft.

Provides aggressive tack and peel adhesion along with superior shear strength. This adhesive bonds to a wide variety of materials including low energy surfaces such as polyethylene and polypropylene. The 2.0 mil adhesive thickness provides the mass needed to establish secure bonds to uneven or irregular surfaces.

An economical means of bonding fabrics, felts, foams and other materials where a reinforcing carrier membrane is not required.

Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. - Stainless Steel 11.00 PSTC-16



Thickness inches -Adhesive Only .002Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)

Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 2.0 mil - 80# White SCK -


TransferFilm

SCK Liner

IF1092A

A 2.0 mil thick film of high performance, rubber based pressure sensitive adhesive. The adhesive is protected by a two side release treated, 60# densified kraft.

Provides aggressive tack and peel adhesion along with superior shear strength. This adhesive bonds to a wide variety of materials including low energy surfaces such as polyethylene and polypropylene. The 2.0 mil adhesive thickness provides the mass needed to establish secure bonds to uneven or irregular surfaces.

An economical means of bonding fabrics, felts, foams and other materials where a reinforcing carrier membrane is not required.




Thickness inches -Adhesive Only .002Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)

Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 2.0 mil - 60# White SCK -


TransferFilm

SCK Liner



IF2012A A 2.0 mil thick film of high performance, acrylic pressure sensitive adhesive. The adhesive is protected by a two side release treated, polycoated natural kraft liner.Provides aggressive tack and high shear strength for quick bonding and long term holding power. The acrylic adhesive has excellent ultra violet light stability and elevated temperature resistance.

The 2.0 mil thickness provides excellent adhesion to most smooth surfaces. This thin adhesive film enables nameplates and faceplates to maintain their engineered low profile appearance.

Complies with U.L. 969 “Marking and Labeling Systems” under both “indoor” and “outdoor” exposure conditions. Test conditionscanbeobtainedbycontactingMACtacorbyconsultingtheMACtacU.L.File#MH12627.




Thickness inches - Adhesive Only .002


Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.0 mil - 83# Brown PCK -


IF20V2 is a 2.0 mil thick film of high performance, acrylic pressure sensitive adhesive. The adhesive is protectedbya72#two-side,release-treated,bleachedpolycoatedkraftliner.

IF20V2 provides aggressive tack and high shear strength for quick bonding and long term holding power. The acrylic adhesive has excellent ultra violet light stability and elevated temperature resistance. The 2 mil thickness of IF20V2 provides excellent adhesion to most smooth surfaces. This thin adhesive film enables nameplates and faceplates to maintain their engineered low profile appearance. The adhesive utilized in IF20V2 complies with U.L. 969 “Marking and Labeling Systems” under both “indoor” and “outdoor” exposure conditions.






Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.0 mil na 74# White PCK -


TransferFilm

Brown PCK Liner

TransferFilm

PCK Liner

IF2013A A 3.0 mil thick film of high performance, acrylic pressure sensitive adhesive. The adhesive is protected by a two side release treated, polycoated natural kraft. Provides aggressive tack and high shear strength for quick bonding and long term holding power. The acrylic adhesive has excellent ultra violet light stability and elevated temperature resistance.

3.0 mil thickness permits more complete contact area on moderately textured, irregular or mismatched surfaces. Typical uses: mounting of nameplates, faceplates, decorative trim, foams, felts, cloth, etc.

Complies with U.L. 969 “Marking and Labeling Systems” under both “indoor” and “outdoor” exposure conditions. TestconditionscanbeobtainedbycontactingMACtacorbyconsultingtheMACtacU.L.File#MH12627.






Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 3.0 mil - 83# Brown PCKSCK -


TransferFilm

Brown PCK Liner

IF20V2

pg. 30

Phone:1-800-328-2619

MACfilm® Acrylic,FreeFilms,SingleLiner


pg.31


IF2015A 5.0 mil thick film of high performance, acrylic pressure sensitive adhesive. The adhesive is protected by a two side release treated, polycoated natural kraft liner.

Aggressive tack and high shear strength for quick bonding and long term holding power. The acrylic adhesive has excellent ultra violet light stability and elevated temperature resistance.

5.0 mil thickness permits more complete contact area on textured, irregular or mismatched surfaces. Typical uses: mounting of nameplates, faceplates, decorative trim, foams, felts, cloth, etc.

IF2015A complies with U.L. 969 “Marking and Labeling Systems” under both “indoor” and “outdoor” exposure conditions.TestconditionscanbeobtainedbycontactingMACtacorbyconsultingtheMACtacU.L.File#MH12627.






Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 5.0 mil - 83# Brown PCK -


IF-2013AP2 is a 3 mil thick film of high performance, acrylic pressure sensitive adhesive. The adhesive is protected by a two side release coated polyester liner.

IF-2013AP2 provides aggressive tack and high shear strength for quick bonding and long term holding power. The acrylic adhesive has excellent ultra violet light stability and elevated temperature resistance. The 3 mil thickness of IF-2013AP2 permits more complete contact area on moderately textured, irregular or mismatched surfaces. Typical uses would include the mounting of nameplates, faceplates, decorative trim, foams, felts, cloth, etc. IF-2013AP2 complies with U.L. 969 “Marking and Labeling Systems” under both “indoor” and “outdoor” exposure conditions.






Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 3.0 mil na 2.0 mil Clear PET -


TransferFilm

Brown PCK Liner

TransferFilm

2.0 MilPET Liner

IF2013AP2



pg. 32

Phone: 1-800-328-2619


IF2092

TransferFilm

PCK Liner

2.0 mil thick film of high tack, modified acrylic pressure sensitive adhesive. The adhesive is protected by atwosidereleasetreated,74#polycoatedwhitekraftliner.

IF2092 provides aggressive tack and peel for quick bonding and long term adhesion. The unique acrylic adhesive bonds to a wide variety of materials with exceptional adhesion to low energy surfaces such as polypropylene and polyethylene.

2.0 mil thickness provides excellent adhesion to most smooth surfaces. The thin adhesive film enables nameplates, faceplates and other decorative attachments to maintain an engineered low profile appearance.

Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in.

7.05.04.04.5

PSTC-16

Peel Adhesion, lbs./in. 7.05.55.06.5

PSTC - 101



Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.0 mil - 74# White PCK -


Stainless SteelHDPELDPEPP

Stainless Steel - 30 minutesHDPE - 30 minutes LDPE- 30 minutes PP - 30 minutes

IF2095

TransferFilm

PCK Liner

5.0 mil thick film of high tack, modified acrylic pressure sensitive adhesive. The adhesive is protected by atwosidereleasetreated,74#polycoatedwhitekraftliner.

Provides aggressive tack and peel for quick bonding and long term adhesion. The unique acrylic adhesive bonds to a wide variety of materials with exceptional adhesion to low energy surfaces such as polypropylene and polyethylene.

5.0 mil thickness permits more complete surface contact to textured, irregular and mismatched surfaces

Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. 11.5

7.86.07.0

PSTC-16

Peel Adhesion, lbs./in. 10.810.28.59.5

PSTC - 101



Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 5.0 mil - 74# White PCK -


Stainless SteelHDPELDPEPP

Stainless Steel - 30 minutesHDPE - 30 minutes LDPE- 30 minutes PP - 30 minutes

Slitting Short Rolls Pattern CoatingSize $/MSI Setup/Release Size $/MSI Setup/Release - 10 MMSI minimum order

- $50 set-up charge

- $0.15/MSI


>6” $0.02 - Less than 540’ $0.06 $25

>2-6” $0.06 - Less than 300’ $0.12 $25

>1-2” $0.10 $25 Less than 150’ $0.17 $25

5/8” - 1” $0.15 $25

MACfilmAdditionalCharges

pg. 33

MACfilm®


IF2043B IF-2043B consists of 3 mils of high-performance, acrylic adhesive and two release liners. The adhesive is protected by 60# White Polycoated Kraft release liner and 4 mil translucent-blue, LDPE film liner.

IF-2043B provides aggressive tack and high shear strength for quick bonding and long term holding power. The 3 mil acrylic adhesive has excellent ultraviolet light stability, elevated temperature resistance and provides excellent adhesion to both smooth and moderately rough surfaces. Typical uses include plate mounting, faceplates, decorative trim, gaskets, etc. The translucent-blue LDPE film release liner allows parts to be vacuum formed while maintaining the integrity of the liner and permits inspection of the laminated parts prior to final assembly.


Peel Adhesion, lbs./in. Stainless Steel - 30 minutes 4.5

PSTC - 101

Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+

PSTC - 107



Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 3.0 mil na 4.0 mil Blue LDPE 60# White SCK


This product is a 1 mil thick film of a general purpose acrylic pressure sensitive adhesive. The adhesive is supplied between two differential release liners to allow ease of handling during the application process. The second liner is a paper adhered to a thin film to provide “tear-free” properties. IF3041 offers a means of bonding a variety of materials where a reinforcing carrier membrane is not required andtheincreasedstiffnessisnotneededordesired.CompliantwithFDA21CFR175.105ToySafetyuseperASTMF963-96a,HasbroSRS-012RevF.


Peel Adhesion, lbs./in. Stainless Steel - 30 minutes 4.0

PSTC - 101

Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F na

PSTC - 107


Temperature Application: Above 25°F (-4°C) for best results. End Use: -75°F to 200°F (-59°C to 93°C)

Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 1.0 mil na Tear Free 2.5 mil SCk


4.0 MilBlue LDPE

Adhesive

SCK Liner

IF3041A 1.0 mil thick film of general performance, acrylic pressure sensitive adhesive. The adhesive is protected by a release treated SCK liner on each side.

Provides good tack and shear strength for immediate adhesion and long term holding power. The acrylic adhesive has excellent ultra violet light stability and elevated temperature resistance.

1.0 mil thickness provides excellent adhesion to most smooth surfaces. IF3041 offers an economical means of bonding a variety of materials where a reinforcing carrier membrane is not required and the increased stiffness is not needed or desired. Excellent choice for flexible magnets. Compliant with FDA 21CFR175.105ToySafetyuseperASTMF963-96a,HasbroSRS-012RevF.






Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 1.0 mil - 2.5 mil SCK 2.5 mil SCK


SCK Liner

Adhesive

SCK Liner

TransferFilm

SCK Liner

IF3041TF

Acrylic,FreeFilms,DoubleLiner

pg.34

Phone:1-800-328-2619

MACmount®

MACmountfoamtapes – These double-coated, polyethylene closed-cell foam tapes offer excellent shear strength and are highly conformable and compressible when applied to uneven, irregular or contoured surfaces. Both general purpose and high-performance rubber-based adhesives are available, as well as high-performance acrylic based adhesives.

•Idealforappliance,transportation,constructionandelectronics applications

•Widerangeofthickness,30milto125milfoamsavailable,designedforfillinggaps

•Appliedincushioning,sealing,sounddampeningand mirrormounting

pg. 35

MACmount®



Rubber,Double-coatedFoams,SingleLiner

IM1705A

A1/32”black,closedcellpolyethylenefoamcoatedonbothsideswithahighshearstrengthrubberbased pressure sensitive adhesive. The adhesive is protected by a two side release treated, polycoated natural kraft liner.

Generally used where the ultimate in holding power is desired for indoor applications. The aggressive adhesive bonds to most surfaces including low energy materials such as polyethylene and polypropylene. The1/32”foamcarrierprovidesagapfillingfunctionwhichaidsinthejoiningofunevenorirregularsurfaces.



Quick Tack, Lbs./sq. in. Stainless Steel 7.5 9.0 MACtac CTM - 25

Peel Adhesion, lbs./in. Stainless Steel - 30 minutes

Foam Tear** PSTC - 101

Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+

PSTC - 107




Rubber/Rubber 2.7 mil / 2.7 mil 1/32” Black PE Foam 83# Brown PCK -

MSI Wt/MSI Roll OD Master Roll Sample Roll

140 0.52 12.4” 54” x 216’ Custom

AdhesiveBlack Foam

AdhesivePCK Liner

IM1800A A1/32”white,closedcellpolyethylenefoamcoatedonbothsideswithahighshearstrengthrubberbased pressure sensitive adhesive. The adhesive is protected by a two side release treated, polycoated natural kraft liner.

Generally used where the ultimate in holding power is desired for indoor applications. The aggressive adhesive bonds to most surfaces including low energy materials such as polyethylene and polypropylene. The1/32”foamcarrierprovidesagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.




Peel Adhesion, lbs./in.Stainless Steel - 1 minute Stainless Steel - 30 minutes Foam Tear**

PSTC - 101


PSTC - 107




Rubber/Rubber 2.7 mil / 2.7 mil 1/32” White PE Foam 83# Brown PCk -


140 0.50 12.4” 54” x 216’ 6” x 20’

AdhesiveFoam

AdhesivePCK Liner

IM1801A A1/32”white,closedcellpolyethylenefoamcoatedonbothsideswithahighshearstrengthrubberbased pressure sensitive adhesive. The adhesive is protected by a two side release treated, semi-bleached kraft liner.





Peel Adhesion, lbs./in. Stainless Steel - 30 minutes

Foam Tear** PSTC - 101


PSTC - 107




Rubber/Rubber 2.7 mil / 2.7 mil 1/32” White PE Foam 60# White SCK -

MSI Wt/MSI Roll OD Master Roll Sample Roll140 0.45 12.0” 54” x 216’ na

** Typically, the adhesion exceeds the strength of the foam in the range of 6 - 9 Lbs./ inch

AdhesiveFoam

AdhesiveSCK Liner

pg.36

Phone: 1-800-328-2619

MACmount® Rubber,Double-coatedFoams,SingleLiner

IM1900A A1/32”white,closedcellpolyethylenefoamcoatedonbothsideswithanaggressive,generalpurpose,rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft release liner.

Developed for general purpose bonding applications. The adhesive bonds to most surfaces including lowenergymaterialssuchaspolyethyleneandpolypropylene.The1/32”foamcarrierprovidesagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.



Peel Adhesion, lbs./in. Stainless Steel - 1 minute Stainless Steel - 30 minutes

Foam Tear**PSTC - 101


PSTC - 107






140 0.35 11.9” 54” x 216’ 6” x 20’

AdhesiveFoam

AdhesiveSCK Liner

IM1810A A1/16”white,closedcellpolyethylenefoamcoatedonbothsideswithahighshearstrengthrubberbased pressure sensitive adhesive. The adhesive is protected by a two side release treated, polycoated natural kraft liner.










Rubber/Rubber 2.7 mil / 2.7 mil 1/16” White PE Foam 83# Brown PCK -


70 0.60 11.6” 54” x 108’ 6” x 20’

AdhesiveFoam

AdhesivePCK Liner

IM1830A A1/16”white,closedcellpolyethylenefoamcoatedonbothsideswithahighshearstrengthrubberbased pressure sensitive adhesive. The adhesive is protected by an 80# two side release treated, semi-bleached kraft liner.












70 0.60 11.6” 54” x 108’ 6” x 20’** Typically, the adhesion exceeds the strength of the foam in the range of 6 - 9 Lbs./ inch

AdhesiveFoam

AdhesiveSCK Liner

pg. 37

MACmount®


Rubber,Double-coatedFoams,SingleLiner








PSTC - 107






70 0.45 11.3” 54” x 108’ 6” x 20’

AdhesiveFoam

AdhesiveSCK Liner








PSTC - 107






70 0.65 15.2” 54” x 108’ 6” x 20’

** Typically, the adhesion exceeds the strength of the foam in the range of 6 - 9 Lbs./ inch

AdhesiveFoam

AdhesiveSCK Liner

pg. 38

Phone: 1-800-328-2619

MACmount® Rubber, Double-coated Films, Single LinerAcrylic,Double-coatedFoams,SingleLinerMACmount®

A1/32”black,closedcellpolyethylenefoamcoatedonbothsideswithahighperformance,modifiedacrylic pressure sensitive adhesive. The adhesive is protected by a blue 5.0 mil HDPE liner.

Provides the excellent temperature properties, holding power and chemical resistance exhibited by acrylicadhesivesplusthestrengthofacross-linkedpolyethylenefoam.The1/32”foamcarrieroffersagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.TheHDPElinerismoistureresistant and provides very good tear resistance.



Peel Adhesion, lbs./in. Stainless Steel - 30 minutes 6.0 5.0

PSTC - 101


PSTC - 107




Acrylic/Acrylic 2.0 mil / 2.0 mil 1/32” White PE Foam 5.0 mil Blue HDPE -


132 0.39 12.1” 51” x 216’ Custom

A1/32”black,closedcellpolyethylenefoamcoatedonbothsideswithahighperformance,modifiedacrylic pressure sensitive adhesive. The adhesive is protected by a blue 5.0 mil HDPE liner.

Provides the excellent temperature properties, holding power and chemical resistance exhibited by acrylicadhesivesplusthestrengthofacross-linkedpolyethylenefoam.The1/32”foamcarrieroffersagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.TheHDPElinerismoistureresistant and provides very good tear resistance.




PSTC - 101


PSTC - 107




Modified Acrylic 2.2 mil / 2.2 mil 20 mil Black PE Foam 80# White SCK -


140 na na 54” x 216’ Custom

IM2908N

AdhesiveBlack Foam

Adhesive

5.0 MilHDPE Liner

A1/32”black,closedcellpolyethylenefoamcoatedonbothsideswithamodified-acrylicpressuresensitive adhesive. The adhesive is protected by a 80# densified, semi-bleached kraft release liner.

Provides the excellent temperature properties, holding power and chemical resistance exhibited by acrylicadhesivesplusthestrengthofacross-linkedpolyethylenefoam.The1/32”foamcarrieroffersagap-fillingfunctionwhichaidsinthejoiningofunevenorirregularsurfaces.




PSTC - 101


PSTC - 107



Adhesive Field/Factory Thickness Carrier Field Liner Factory Liner

Acrylic/Acrylic 2.0 mil/ 2.0 mil 1/32” Black PE Foam 80# White SCK -


140 0.39 12.1” 54” x 216’ Custom

IM2908-80

AdhesiveBlack Foam

AdhesiveSCK Liner

AdhesiveBlack Foam

AdhesiveSCK Liner

IM2901




pg.39

MACmount®


MACmountAdditionalChargesSlitting Short Rolls Pattern CoatingSize $/MSI Setup/Release Size $/MSI Setup/Release - 10 MMSI minimum order

- $50 set-up charge

- $0.15/MSI


>6” $0.05 - Less than 750’ $0.06 $25

>2-6” $0.10 - Less than 300’ $0.12 $25

>1-2” $0.15 $50 Less than 150’ $0.17 $25

5/8” - 1” $0.20 $50

<5/8”(3/8”-1/2”)

The listed web width is the minimum purchase however, please note the following for these narrow rolls:54” wide web material will yield 51” of material available to ship51” wide web material will yield 48” of material available to shipThe additional charges will be the same as 5/8”-1” for these sizes.Shipments of material with widths less than 5/8” may be - 25% of original quantity requested.

A1/32”white,closedcellpolyethylenefoamcoatedonbothsideswithahighperformance,modifiedacrylic pressure sensitive adhesive. The adhesive is protected by a 60# densified, semi-bleached kraft release liner.

Provides the excellent temperature properties, holding power and chemical resistance exhibited by acrylicadhesivesplusthestrengthofacross-linkedpolyethylenefoam.The1/32”foamcarrieroffersagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.



Peel Adhesion, lbs./in. Stainless Steel - 1 minute Stainless Steel - 30 minutesStainless Steel - 24 hours

5.56.58.5

4.56.08.0

PSTC - 101





Acrylic/Acrylic 2.0 mil / 2.0 mil 1/32” White PE Foam 60# White SCK -


140 0.34 11.8” 54” x 216’ 6” x 20’

IM2920

AdhesiveFoam

AdhesiveSCK Liner

A1/16”white,closedcellpolyethylenefoamcoatedonbothsideswithahighperformance,modifiedacrylic pressure sensitive adhesive. The adhesive is protected by a 60# densified, semi-bleached kraft release liner.

Provides the excellent temperature properties, holding power and chemical resistance exhibited by acrylic adhesives plus the strength of a cross-linked polyethylene foam.The 1/16” foam carrier offers agapfilling function that aids in the joining of uneven or irregular surfaces.



Peel Adhesion, lbs./in. Stainless Steel - 1 minute Stainless Steel - 30 minutesStainless Steel - 24 hours

6.5^7.5^8.5^

6.0^6.5^8.0^

PSTC - 101


PSTC - 107




Acrylic/Acrylic 2.0 mil / 2.0 mil 1/16” White PE Foam 60# White SCK -


70 0.44 11.3” 54” x 108’ 6” x 20’^ Partial foam tear. Typically, the adhesion exceeds the strength of the foam.

IM2940

AdhesiveFoam

AdhesiveSCK Liner

Acrylic,Double-coatedFoams,SingleLiner

pg.40

Phone:1-800-328-2619

GS SeriesGSSeriesAdhesives – Specially formulated to provide instant, very aggressive tack and peel adhesion as well as superior shear strength, GS Series high-strength adhesive tape is durable enough to replace many mechanical fasteners. Ideal for permanent bonding of substrates in the assembly and manufacturing industries.

•Idealforpackaging,transportation,constructionand P.O.P applications

•Availablein5.0milto50milthickness

•Availablein1/2”to11-1/2”adhesivewidths

•Usedinvibrationdampeningandpackagingassemblies

•Speedsassemblyandlowersmanufacturingcosts

•Fills gaps

•Actsasamoisturebarrier

pg.41

GS Series


High-StrengthAdhesiveTapes

TheGS-SeriesofstripadhesivesaremadeupofanunsupportedSBRpressuresensitiveadhesive,specially coated by MACtac using a patented, proprietary process, and wound on a 60# densified kraft release liner.

The adhesive used in the GS-Series provides very aggressive tack and peel adhesion along with superior shear strength. This adhesive bonds to a wide variety of materials including low energy surfaces such as polyethylene and polypropylene. The standard thicknesses of 5 to 50 mils provides the mass needed to establish secure bonds to uneven or irregular surfaces.

TheGS-Seriesstripadhesivesareavailableinanumberofnarrowwidthsizesrangingfrom1/4”to111/2”.Thetoleranceforanygivenwidthis+/-1/16”.Typicallyprovidedasasingleordoublestripofadhesive on the 60# liner, each roll has ungummed edges for ease of handling and quick liner removal. There are manufacturing limitations, however, so please contact your district sales manager to review your application in order to determine suitability.

TheGSSeriesisalsoavailablewitha2milpolyesterlinerasacustomconstruction.

*Customandmade-to-ordersizesareavailable,contactsalesorcustomerservice.

GS2004 5.0 mil version of high peel and tack adhesive free film for difficult to adhere to substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assembly.

Performance Test Typical Values Testing MethodQuick Tack, Lbs./sq. in. - Stainless Steel 20+

Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 22+ PSTC - 101




Adhesive Field/Factory Ct Wt Carrier Field Liner Adh. Width/Liner Width

Rubber 5.0 mil - 60# White SCK 1.00” / 1.50”

MSI Wt/MSI Roll OD Master Roll Sample Roll16.2 0.28 11.4” 5.0 mil x 1.5” x 900’ 5.0 mil x 1.5” x 50’

TransferFilm

SCK Liner

GS1003 20.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assembly







Rubber 20 mil - 60# White SCK 0.50” / 1.00”


TransferFilm

SCK Liner

pg.42

Phone:1-800-328-2619

GS SeriesGS1001 20.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and

mounting to irregular surfaces; semi-structural bonding; good for assembly.









GS1013 20.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assembly









GS1039 30.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assemblyPerformance Test Typical Values Testing Method

Quick Tack, Lbs./sq. in. - Stainless Steel 20+








30.0 mil x 1.0” x 500’ 30.0 mil x 1.0” x 50’

TransferFilm

SCK Liner

TransferFilm

SCK Liner

TransferFilm

SCK Liner










TransferFilm

SCK Liner

pg.43

GS Series


High-StrengthAdhesiveTapes

GS1007 35.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assembly Performance Test Typical Values Testing Method

















MSI Wt/MSI Roll OD Master Roll Sample Roll7.2 1.97 11.6” 50.0 mil x 2.5” x 200’ na










TransferFilm

SCK Liner

TransferFilm

SCK Liner

TransferFilm

SCK Liner

pg.44

Phone:1-800-328-2619

pg.44

PhenolicTapes The MACtac® IF4020 Series was developed for bonding friction materials with fewer environmental and safety issues than solvent-based adhesives, MACtac has developed a series of heat-activated, dry film adhesive products. MACtac’s dry film nitrile-phenolic tapes provide permanent adhesion to a variety of wet-laid fibers (paper), carbon and other friction materials utilized in automotive OEM, aerospace, heavy equipment, lawn and garden, and industrial applications.

The new series addresses solvent-evaporation and adhesive quantity issues common with liquid adhesives. It also reduces waste and improves overall manufacturing efficiency by allowing pre-measured tapes to be pre-applied in-line to raw materials or converted parts usingmodestheat-assistlamination(approx.66°C/150°F).Thefinalbond of the adhesive-coated friction material to its companion is completed at a higher temperature and pressure. This allows for greater speed-to-market when compared to parts manufactured with liquid adhesives, which can take up to a day to cure.

The series demonstrates high strength properties at low and elevated temperatures and excellent chemical resistance. This combination is critical for friction applications where parts are subjectedtohighoperatingtemperatures,energyabsorptionandpressures, as well as exposure to chemicals such as transmission and brake fluids.

•Permanentadhesionwherepartsareexposedtochemicalssuchastransmissionfluids.

•Idealforhigh-temperatureresistanceapplications

•Highperformanceapplications

pg.45


NitrilPhenolicFilmedAdhesivePhenolicTapesIF4020A

IF4023A A 2.2 mil thick dry film of thermosetting adhesive. It is protected by a 84# polycoated kraft liner, release coated on two sides.

The adhesive can typically be transferred from the protective release liner to the bondable substrate withtheuseofmodestheat(approx.150°F).Theselectedcurescheduleshouldthenbeperformedto obtain full bond to the end use substrate.

When properly cured, IF-4023A exhibits good strength properties at both low and elevated temperatures.Italsoexhibitsexcellentplasticflowwhichcontributestowardobtaining100%contactwith the substrates to be bonded. The material becomes thermoset after cure.

Performance Test Typical Values Testing MethodDisc Shear Strength psi 73°F 400°F

2500+500+

SAE J840

Curing ConditionsThe desired disc shear strength can be obtained with any of the following “Bond-Line” temperatures and times:. A. 350° F for 15 minutes B. 370° F for 10 minutes C. 400° F for 5 minutes

Ct Wt Field Liner Factory Liner

2.2 mil 84# White PCK na

Roll OD Master Roll Sample

13.8” 60” x 1,800’ 8” x 10” Sheets

Dry Film

SCK Liner

Dry Film

PCK Liner

A 1.0 mil thick dry film of thermosetting adhesive. It is protected by a 60# densified kraft liner, release coated on both sides.

The adhesive can typically be transferred from the protective release liner to the bondable substrate withtheuseofmodestheat(approx.150°F).Theselectedcurescheduleshouldthenbeperformedto obtain the full bond to the end use substrate.

When properly cured, IF-4020A exhibits good strength properties at both low and elevated temperatures.Italsoexhibitsexcellentplasticflowwhichcontributestowardobtaining100%contactwith the substrates to be bonded. The material becomes thermoset after cure.

Performance Test Typical Values Testing MethodDisc Shear Strength psi 73°F 400°F

2500+500+

SAE J840

Curing ConditionsThe desired disc shear strength can be obtained with any of the following “Bond-Line” temperatures and times:. A. 350° F for 15 minutes B. 370° F for 10 minutes C. 400° F for 5 minutes

Ct Wt Field Liner Factory Liner

1..0 mil 60# White SCK na

Roll OD Master Roll Sample

11.2” 56” x 1,800’ 8” x 10” Sheets

pg.46

Phone: 1-800-328-2619

Safety GritA permanent, conformable PSA product that provides a safe, non-slip surface.

•Finelyground,siliconcarbidegrit,uniforminsizeand evenly distributed.

•Water-resistantgritallowsforexposuretoharsh interiorandexteriorenvironments.

•Industrialstrengthfilmcarrierpreventsrot,offershighmoistureresistanceandinsuresstability.

•Wet/drycarrierresiststearing,chippingandflaking.

•Highquality,hightackrubber-basedadhesiveadheres to a wide variety of substrates including painted and unpaintedwood,metalandetchedconcrete.

•Adhesiveresistswater,alcoholsanddetergent.

pg.47


Safety Grit

IC6187

Consists of a finely ground mineral abrasive permanently bonded to one side of a high-strength, non-tearing plastic carrier film with an adhesive on the opposite side. The permanent pressure sensitive adhesive is protected with a kraft paper release liner.

Providesalowprofile,non-slipmaterialforinterior/exteriorsurfacessuchasshopfloors,stairs, loading ramps, ladders, recreational vehicles, diving boards, skateboards, etc. The adhesive provides instant secure bonding with no lifting even in high-traffic areas.

Performance Test Typical Values Testing MethodShear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F

100+ PSTC-7

Peel Adhesion, lbs./in. Stainless Steel - 30 minutes 5.0 PSTC-1

Thickness inches - Film plus adhesive .020


Adhesive Field/Factory Ct Wt Carrier Field Liner Factory Liner

Rubber 2.1 Plastic 80# White CCK -

MSI Wt/MSI Roll OD Master Roll Sample Sheet

162 0.81 11” 54” x 250’ Custom

GritPlastic

AdhesiveCCK Liner

SafetyGritAdditionalChargesSlitting Short RollsSize $/MSI Setup/Release Size $/MSI Setup/Release

>6” $0.05 - Any Short Roll $0.20 $50

>2-6” $0.10 $75

>1-2” $0.15 $75


pg.48

Phone: 1-800-328-2619

Specialty Products Rubber, Double-coated Films, Single LinerBuilding&ConstructionApplication IdeasFrom the inside to the outside, MACtac® has adhesive products perfectly suited for the building and construction markets. Products in this area include cold application temp HVAC tapes as well as PSA for Window and Door sealing and mounting. For high performance and high value, look to MACtac for Building and Construction needs.

Products mentioned below are proven effective for the associated applications, but by no means represent the entirety of MACtac’s product offering. Our Sales and Technical Marketing teams are ready to provide specific product recommendations.

Application Product Substrates Product Benefit

PipeInsulation(HVAC) Building Products

Bonding to common insulation facings (Foil, ASJ & FSK)

With a variety of Faces such as Foil, ASJ, Soft White Vinyl and Scrim, MACtac BuildingProducts meet a wide range of performance criteria for HVAC applications.

WindowsandDoorsSealing

IB119XAIB213X

Bonding various solid or foamed seals to glass, metal, wood & PVC

Whether replacement wndows or new construction, MACtac has products for sealing IG units, setting replacements, and a wide variety of gasket and protection materials. IB119XA bonds well to plastics and provides for vibration and acoustical noise reduction. IB213X provides higher temperature performance and UV resistance.

Roofing,FaçadeInsulation

GS-Series Bonding various plastic or rubber seals to metal, wood & PVC

GS-Seriesthick mass of adhesive from 5 to 50mils provides a very aggressive bond for high shear applications. GS-Series allows for elimination of rivets and mechanical fasteners, and acts as a seals substrates from moisture

Acoustic Insulation IB1188 Bonding sound & vibration-damping materials to metals, wood & plastics

Bonds well to foams, with the shear strength needed for permanent wall mounting, IB1188 is used in a number of noise and vibration dampening applications inside and outside of the home.

Bumpers Specialty Bumper Films

Bonding cast urethane bumpers to metal, plastic, wood & glass

MACtacusesspecialtyfilmsinconjunctionwithstandard,highperformance rubber and acrylic adhesives to provide the right properties for Bumpers going into cabinets, electronics and more.

General Purpose MountingandBonding

IM18XXA Similar & dissimilar metals, plastics &natural/syntheticfibers

For high shear wall mounting, IM18XXA acts as a gap filler with excellent adhesion.

CarpetMounting,FloorInstallation

IB1178AIB6280

GS-Series

Bonding similar & dissimilar materials including wood, plastic, metal & carpeting

IB1178A provides stability to various commercial landing tiles, while the scrim carrier and environmental resistance of IB6280 works well around corners with initial repositionability. For wood, PVC & carpet trim pieces, GS-Series products provide both aggressive adhesion and excellent cohesive strength.

SecurityWindowFilms Specialty Window

Bonding to glass, polycarbonate & other transparent substrates

In addition to adding cosmetic appearance to glass used in furniture, window and cabinet doors, MACtacWindowFilmsoffer a unique safety feature.

SettingBlocks IF1092A Bonding various rubber materals to other window components

Thin profile, economic with excellent performance, IF1092A 2.0 mil rubber free-film provides necessary support for durable setting blocks.

pg.49

Specialty Products Rubber, Double-coated Films, Single Liner


Appliance ApplicationsApplication IdeasAppliance applications present unique challenges for which MACtac® has a variety of standard and custom solutions. From UL Listed Acrylic products that bond well to high and low surface energy surfaces to economical rubber adhesives, MACtac has partnered with Appliance OEM’s and suppliers for many years to change how PSA’s fit into their process.

Products mentioned below are proven effective for the associated applications, but by no means represent the entirety of MACtac’s product offering. Our Sales and Technical Marketing teams are ready to provide specific product recommendations.


SoundDampening IB1175AERGS-Series

Sound & vibration-damping foams to metals & plastics.

IB1175AER has excellent wetting properties for challenging substrates such as porous foams, and an easy-release liner for problem-free dispensing of die-cut, soft-foam gaskets.

InsulationBonding IM18XXAIM29XX

Bonding plastic-encapsulated insu-lation to metals & plastics

Availableincombinationsof1/32”,1/16”,and1/8”withblackand white foams, the IM18XXA has excellent shear and heat resistance for a rubber adhesive, while IM29XX products provides acrylic performance.

Gasket and Seal Mounting

IB119XA Bonding gasket materials including foams to metals & plastics

IB119XA is a high performing workhorse rubber adhesive ideal for a wide variety of applications. A softer adhesive bonds well to challenging surfaces, while the heavier factory-side coat weight flows into porous substrates.

Nameplate&GraphicOverlays

IF201XAIF209X

Plastic or metal to variety of plas-tics & powder-coated paints.

Thin profile acrylic free-films, IF201XA provides good adhesion and environmental resistance to standard surfaces, while IF209X handles the challenges of lower surface energy materials like powder coated paints and plastics.

FoamMounting IM18XXAIM19XXA

Bonding unpainted metals to painted metals & various plastics

IM18XXA offers a higher performance product for difficult applications. IM18XXA uses a heavier coat weight rubber adhesive with better shear and temperature resistance than IM19XXA. Both IM18XXA and IM19XXA are available in 1/32”,1/16”and1/8”whiteandblackPEfoam.

ScrewAnchors IM18XXAIM19XXA

Bonding unpainted metals to painted metals & various plastics

IM19XXA offers greater value than IM18XXA where general performance is required. Additionally, as a softer adhesive, it may succeed where other rubber adhesives fail. Both IM18XXAandIM19XXAareavailablein1/32”,1/16”and1/8”white and black PE foam.

DecorativeTrimBonding

IF201XAIF209X

IB119XA

Bonding trim to various paints. LSE plastics & powder-coats.

IF201XA acrylic freefilms provide excellent adhesion and environmental resistance to high surface energy substrates, while IF209X handles low surface energies. IB119XA has a variety of widths and liners for applications that do not require the environmental and heat resistance of an acrylic.

Door HandleBonding GS-Series Bondingpainted/platedmetalsorplastic parts to various paints.

GS-Series thick mass of adhesive from 5 to 50mils provides a very aggressive bond for high shear applications. GS-Series allows for elimination of rivets and mechanical fasteners, and acts as a seals substrates from moisture.

ProtectiveDoorLiners Optically Clear Glass & polycarbonate windows; painted metal surfaces

MACtac has a variety of Optically Clear adhesives and overlaminates originally developed for photo lamination.

PSALabelStock Label Products Painted metals, plastics & glass For more information about a large variety of PrintableLabelProducts,contactyourMACtacSalesRepresentative.

pg. 50

Phone: 1-800-328-2619

Specialty Products Rubber, Double-coated Films, Single LinerRV&MarineApplicationsApplication IdeasMarine&RVpresentchallengesduetotheharshenvironment.Reducingnoise,adhering through shock and vibration, heat and chemicals, MACtac® has developed and specified a variety of products with leading OEM’s.

Products mentioned below are proven effective for the associated applications, but by no means represent the entirety of MACtac’s product offering. Our

Sales and Technical Marketing teams are ready to provide specific product recommendations.


Heat,SoundandVibrationInsulation

IB118XIB1175AER

IF201X

Flatand/ormoldedrubbertometal, plastic and other substrates

The IB118X family provides excellent tack and better heat and shear resistance than other rubber adhesives. Available in a variety of widths and liner thickness, many IB118X products have been tested to automotive standards. IB1175AER flows more easily to adhere to challenging substrates with an easy removable liner.

Non-SlipTape IC6187 Painted & unpainted metal, plastic, wood and other substrates

MACtac Safety Grit provides non slip surfaces for a wide varietyofsubstratesinMarine,RVandindustrialequipment.

DecorativeGraphics Various Various For more information on a wide variety of Graphic Products contactyourSalesRepresentative.

Mirror Mounting IM2908-80IM2901

Coated mirror to ABS and other molded plastics

IM2908-80 is a proven product in the automotive industry for anti-shatter requirements in a challenging environment.

Gaskets/Seals IB118XIB2125AIB213X

Bonding similar & dissimilar materi-als – metals and plastics

IB1182’sHighTackRubberAdhesiveisacosteffectivesolutionwith good initial adhesion and shear strength. IB2125A uses one side rubber, one side acrylic for applications with different substrate requirements.

Roof/WallAssembly GS-Series Bonding similar & dissimilar materials – metals and plastics

GS-Series thick mass of adhesive from 5 to 50mils provides a very aggressive bond for high shear applications. GS-Series allows for elimination of rivets and mechanical fasteners, and acts as a seals substrates from moisture.

InteriorTrim IB6280IF2083IB213X

Foam-backed fabrics & PVC’s to fiberglass & other plastics

IB6280’s High Performance Acrylic combined with a Scrim Carrier provides structure that is still conformable for curved and uneven substrates. Available with different coat weights, and in Freefilm and Double-coated PET.

DeckingMaterial IB2180IF209X

Smooth and non-skid fiberglass to semi-rigid flooring

Specially designed to withstand the harsh marine environment and resist plasticizer migration, the IF209X family offers exceptional performance for demanding applications.

Carpet/Flooring IB2180IF209X

Fiberglass & other plastics to car-pet backings

Initially repositionable, the IF209X free films and double-coats build adhesion quickly, allowing for ease of installation and the removal of liquids and sprays commonly used today with almost no setting time.

Engine Cover IB2180 Fiberglass and other plastics to various sound-deadening foams

IB2180 provides heat resistance and adhesion necessary for foams and similar materials used in sound and vibration dampeninginmarineandRVenginecompartments.

pg.51

Specialty Products Rubber, Double-coated Films, Single Liner


AutomotiveApplicationsApplication IdeasMACtac offers a wide variety of pressure sensitive adhesives that have been certified to domestic and imported automotive standards. For a list of automotive certs or more information, please contact MACtac Customer Service at 1.800.321.0011

Products mentioned below are proven effective for the associated applications,

but by no means represent the entirety of MACtac’s product offering. Our Sales and Technical Marketing teams are ready to provide specific product recommendations.


Nameplates IF2012A IF209XIM29XX

Painted Surface to Molded Plastic IF2012A High Performance Acrylic offers strong adhesion and peel strength to high surface energy metals and plastics. IF2092’s LSE adhesive provides excellent adhesion to lower surface energy materials such as powder coated paints.

RubberGaskets/Seals IB1182XIB2125AIB213X

RubbertoMoldedPlastic IB1182’sHighTackRubberAdhesiveisacosteffectivesolutionwith good initial adhesion and shear strength. IB2125A uses one side rubber, one side acrylic for applications with different substrate requirements.

DashboardAssembly/NavigationSystem

IF201XAIF2043B

PET Film to Molded Plastic Graphic Overlays and gauges can be assembled in thin profile with IF2012A Series or higher performing IF2043B for more challenging applications.

InteriorTrim IB6280IF2083IB213X

Foam Backed Fabric & Vinyl Molded Trim Materials to Filled PP

IB6280’s High Performance Acrylic combined with a Scrim Carrier provides structure that is still conformable for curved and uneven substrates. Available with different coat weights, and in Freefilm and Double-coated PET.

Carpet/Shoddy IB1188IB1184

GS

WovenCarpet/ShoddytoTPO/Metal

IB1184's heavy coat weight flows well into irregular surfaces. IB1188 uses a differential coat weight to reduce cost where one substrate is more challenging than the other. From 5 to 50 mils thick, GS-Series rubber based adhesive provides tremendous bonding of a wide variety of adhesives.

TailightConstruction IB1182 RubbertoMoldedPlastic IB1182'sHighTackRubberAdhesiveisacosteffectivesolutionwith good initial adhesion and shear strength.

Sound/VibrationDampening

IB118XIB1175AER

Felt/Nonwoven/FoamtoTPO/Metal

MACtac has a wide array of products for Sound and Vibration, from high tack rubber IB118X series, to the very easy release IB1175AER series for soft, easily torn materials. Acrylic and Rubber/Acrylicproductsarealsoavailable.

Mirror Mounting IM2908-80IM2901

Coated Mirror to ABS IM2908-80 is a proven product in the automotive industry for anti-shatter requirements in a challenging environment.

Transmission/ClutchFrictionDisc

IF4023IF4020

Ferrous and Non-Ferrous Metal to Carbon

IF4023 Phenolic products hold up under high heat and pressure to provide structural adhesion of carbon friction components.

HVACDucts IB1185L12IB1175AERIB2125A

Foam to TPO Plastic IB1185L12’s 12pt tag liner acts as a tray for diecut parts, allowing for ease of hand assembly and otherwise makes starting the liner easier on materials with low internal strength. IB1175AER’s 80# liner removes smoothly and easily from foam/felt/shoddy.

pg. 52

Phone: 1-800-328-2619

FoamFabricationAdhesive Recommendations

Chemistry ProductPE Foam PE Foam

4# to 6# Volara Foam

4# to 6# Volara Foam

Mincel Foam Mincel Foam PVC Foam PVC Foam

30 Min. 1 Week 30 Min. 1 Week 30 Min. 1 Week 30 Min. 1 Week

Rubber

IB1175A + ++ ++ +++ ++ +++ +++ +++IB1178A + ++ + +++ + +++ ++ +++IB1182/-3/-5 + ++ ++ +++ + +++ ++ +++IB1184 ++ +++ +++ +++ ++ +++ +++ +++IB1190A + ++ ++ +++ ++ +++ +++ +++

Acrylic

IB2012 + ++ + ++ + ++ + ++IF2015 + ++ ++ ++ ++ ++ ++ ++IB2092/IF2095 ++ +++ +++ +++ +++ +++ +++ +++IB2100 + ++ + ++ + +++ + ++IB2130 + ++ + +++ + +++ +++ +++

++

Chemistry Product

Neoprene Foam SCE

41, 43

Neoprene Foam SCE

41, 43

Poron Foam

Poron Foam

Vinyl Nitrile Foam

Vinyl Nitrile Foam

2#, 4#, 6# UL Ester

Urethane Foam

2#, 4#, 6# UL Ester

Urethane Foam

EPDM Foam

EPDM Foam

30 Min. 1 Week 30 Min. 1 Week 30 Min. 1 Week 30 Min. 1 Week 30 Min. 1 Week

Rubber

IB1175A ++ +++ ++ +++ ++ +++ ++ +++ ++ +++IB1178A + ++ + ++ + +++ + +++ + +++IB1182/-3/-5 ++ +++ + +++ ++ +++ + +++ ++ +++IB1184 +++ +++ +++ +++ +++ +++ ++ +++ +++ +++IB1190A ++ ++ ++ +++ ++ +++ ++ +++ ++ +++

Acrylic

IB2012 + ++ + +++ + + + ++ ++ +++IF2015 ++ ++ ++ +++ ++ +++ ++ ++ ++ +++IB2092/IF2095 +++ +++ +++ +++ +++ +++ +++ +++ +++ +++IB2100 + ++ + +++ + +++ + ++ ++ +++IB2130 + ++ ++ +++ ++ +++ + +++ ++ +++

These recommendations are based on previous history and testing and do not mean that all recommended products will work as every application is unique. It is the sole responsibility of the customer to determine fitness for use in each application prior to the purchase of any MACtac product

+ mild Bond, Improved with Pressure or Heat++ Agressive Bond +++ Destruction of Foam When Removed

pg. 53


MACtac®ProductsYouShouldKnowBasket of 12Product Ct Wt mil

Field/Factory Carrier Master RollSample Roll MSI Peel Tack Temp

Max Performance Description Liner Recommended For

Rub

be

r

IB1178A 1.2/1.2 1/2 mil PET54” x 750’

6” x 30’486 8.0/8.0 10.0/10.0 180°F Good

Cost effective general purpose bonding to smooth surfaces

60# White SCK

Any general performance bond

IB1190A 1.2/1.8 1/2 mil PET54” x 750’

6” x 30’486 8.5/9.5 10.5/12.5 180°F Better

Great tack and peel on a wide variety of substrates especially

non-plasticized foams and gaskets. A cost

effective solution to foam bonding and

other more challenging substrates

60# White SCK

Foam Fabrication, Gasketing, PET

Urethane foam, PE Foam, sponge, plastic, rubber, compressed

sheet

IB1200A 2.7/2.7 1.0 mil PP54” x 750’

6” x 30’486 11.5/12.0 6.0/4.5 180°F Best!

Heavy coat-weight for high performance

requirements. 1-mil PP carrier for excellent

conformability while increasing the integrity of your bond

60# White SCK

Very high performance applications

OEM Specification, PE Foam, sponge,

plastic, rubber, cork, compressed sheet

DC

Fo

am

Tap

e

IM1900A 1.8/1.81/32” white

PE foam54” x 216’

1” x 5’140 *** *** 150°F Good

General purpose bonding and mounting

between irregular and LSE substrates.

80# White SCK

Appliance / assembly aid

IM1800A 2.7/2.71/32” white


1” x 5’140 *** *** 150°F Better

High coat-weight, high performance

bonding and mounting between irregular and LSE substrates.

80# White SCK

General purpose mounting

application. Moderate to High shear mounting

IM2908 2.0/2.01/32” black


1” x 5’140 *** *** 200°F Best!

High performance Acrylic Foam Tape

80# White SCK or 5.0 mil

blue HDPE

Soap Dispenser or mirror mounting. High

shear mounting

Ac

rylic

DC

IB2101 1.1/1.1 1/2 mil PET54” x 750’

6” x 30’486 3.5/3.0 2.4/2.5 250°F Good

Acrylic double-coat, resistant to plasticizers, high temperatures,

and chemicals in a cost effective coat weight

60# White SCK

Cost effective bonding, mounting,

nameplates, faceplates,

decorative trim, PET Urethane,

Polyether, PVC Foam

IB2130 1.5/1.8 1/2 mil PET54” x 750’

6” x 30’486 4.5/4.5 6.5/6.5 250°F Best!

Modified-Acrylic, excellent temperature

resistance, tack, peel and shear on a

wide variety of substrates

74# White SCK

For High-Tack, High-Temperature

application, gasket, seals, automotive,

appliance.

Ac

rylic

FF

IF2012A 2.0 mil None54” x 540’

6” x 30’350 4.1 4.0 250°F Bood

UL rated, high performance acrylic,

2 MIL, high shear with UV and temperature resistance

83# Brown PCK

Cost effective acrylic bonding

applications, nameplates, faceplates,

gaskets, foams

IF2015A 5.0 mil None54” x 540’

6” x 30’350 5.0 5.5 250°F Best!

UL rated, high performance acrylic,

5 MIL, high shear with UV and temperature resistance

83# Brown PCK

High performance acrylic bonding

applications, nameplates, faceplates,

gaskets, foams

LSE

Ac

rylic

FF IF2092 2.0 mil None

54” x 540’6” x 30’

350 7.0 7.0 250°F Good2 mil High performance

acrylic freefilm, LSE74# White

PCK

LSE PP, PE, Powder-coated paints,

aggressive peel and tack

IF2095 5.0 mil None54” x 540’

6” x 30’350 10.0 10.0 250°F Best!

5 mil High performance acrylic freefilm, LSE

74# White PCK

Heavy coat-weight LSE PP, PE, Powder-

coated paints, aggressive peel and

tack

pg.54

Phone: 1-800-328-2619

Conversions&FractionsMetric to Inchesmillimeters Decimal Inches 1mm .03937 2mm .07874 3mm .11811 4mm .15748 5mm .19685 6mm .23622 7mm .27559 8mm .31496 9mm 35433 10mm .39370 11mm .43307 12mm .47244 13mm .51181 14mm .55118 15mm .59055 16mm .62992 17mm .66929 18mm .70866 19mm .74803 20mm .78740 21mm .82677 22mm .86614 23mm .90551 24mm .94488 25mm .98425

Thickness Conversion Formulas Inches x 0.0833 = Feet Inches x 25.4 = mm Inches x 25,400 = Microns mils x 25.4 = Microns mils x 0.001 = Inches Microns x 0.03937 = mils Microns x 0.0001 = cm mm x 1000 = Microns mm x 39.37 = mils .0254 x mils = mm

Metric to InchesThese formulas provide a simple method for converting frequent-ly encountered units for web or sheet materials.

MSI (1000 square inches) to: MSI divided by 0.144 = Ft2 (square feet) [Example: 25 MSI ÷ 0.144 = 173.61 Ft2]

MSI divided by 1.296 = Yd2 (square yards) [Example: 25 MSI ÷ 1.296 = 19.29 Yd2]

MSI divided by 1.550 = m2 (square meters) [Example: 25 MSI ÷ 1.550 = 16.13 m2]

Ft2 (square feet) to: Ft2 times 0.144 = MSI (1000 square inches) [Example: 200 Ft2 x 0.144 = 28.8 MSI]

Ft2 times 0.1111 = Yd2 (square yards) [Example: 200 Ft2 x 0.1111 = 22.22 Yd2]

Ft2 times 0.0929 = m2 (square meters) [Example: 200 Ft2 x 0.0929 = 18.58 m2]

Yd2 (square yards) to: Yd2 times 1.296 = MSI (1000 square inches) [Example: 200 Yd2 x 1.296 = 259.2 MSI]

Yd2 times 9.0 = Ft2 (square feet) [Example: 200 Yd2 x 9.0 = 1800 Ft2]

Yd2 times 0.8361 = m2 (square meters) [Example: 200 Yd2 x 0.8361 = 167.22 m2]

m2 (square meters) to: m2 times 1.55 = MSI (1000 square inches) [Example: 50 m2 x 1.55 = 77.50 MSI]

m2 times 10.7639 = Ft2 (square feet) [Example: 50 m2 x 10.7639 = 538.20 Ft2]

m2 times 1.196 = Yd2 (square yards) [Example: 50 m2 x 1.196 = 59.80 Yd2]

MSI to lineal feet for a 54” wide web MSI divided by 0.648 = lineal feet [Example: 500 MSI ÷ 0.648 = 771.6 lineal feet]

Lineal feet to MSI for a 54” wide web Lineal feet times 0.648 = MSI (1000 square inches) [Example: 250 lineal feet x 0.648 = 162 MSI]

MSI to lineal feet for 60” wide web MSI divided by 0.720 = lineal feet [Example: 500 MSI ÷ 0.720 = 694.4 lineal feet]

Lineal feet to MSI for a 60” wide web Lineal feet times 0.720 = MSI (1000 square inches) [Example: 250 lineal feet x 0.720 = 180 MSI]

pg. 55


Conversions&FractionsConversion FormulasLocate the known unit of measurement across the top row. Find the unknown unit of measurement down the left column. Follow the appropriate row and column until they intersect. Multiply the number listed at the point of intersection.

Units of Length

mili- Centi- UNIT Inch Foot Yard meter meter Meter (in) (ft) (yd) (mm) (cm) (m)

inch 1 12 36 0.03937 0.3937 39.37

foot 0.08333 1 3 0.00328 0.0328 3.281

yard 0.02777 0.333 1 0.00109 0.0109 1.094

mm 25.4 304.8 914.4 1 10 1000

cm 2.54 30.48 91.44 0.1 0 100

meter 0.0254 0.305 0.915 0.001 0.01

Units of Capacity - U.S. Liquid Measure

Fluid mili- CubicUNIT Ounce Quart Gallon liter Liter Inch (fl oz) (qt) (ga) (ml) (l) (in£)

fl oz 1 32 128 0.0338 33.8148 0.5541

quart 0.03125 1 4 0.00106 1.0567 0.01732

gallon 0.0078 0.25 1 0.000264 0.264 0.00433

ml 29.57286 946.3316 3785.327 1 1000 16.387

liter 0.02957 0.9463 3.7853 0.001 1 0.01639

in£ 1.80469 57.75 231 0.06102 61.02 1

Fraction EquivalentsFractional Inches Decimal Inches millimeters

1/64 0.015625 0.397

1/32 0.031250 0.794

3/64 0.046875 1.191

1/16 0.062500 1.588

3/32 0.093750 2.381

1/8 0.125000 3.175

5/32 0.156250 3.969

3/16 0.187500 4.763

7/32 0.218750 5.556

1/4 0.250000 6.350

9/32 0.281200 7.144

5/16 0.312500 7.938

11/32 0.343700 8.731

3/8 0.375000 9.525

13/32 0.406200 10.319

7/16 0.437500 11.113

15/32 0.468700 11.906

1/2 0.500000 12.700

17/32 0.531200 13.494

9/16 0.562500 14.288

19/32 0.537500 15.081

5/8 0.625000 15.875

21/32 0.656200 16.669

11/16 0.687500 17.463

23/32 0.718700 18.256

3/4 0.750000 19.050

25/32 0.781200 19.844

13/16 0.812500 20.638

27/32 0.843700 21.431

7/8 0.875000 22.225

29/32 0.906200 23.019

15/16 0.937500 23.813

31/32 0.968700 24.606

1 1.000000 25.400

pg.56

Phone: 1-800-328-2619

Conversions&FractionsThickness Conversion Chart

mils Microns1 25.4

2 50.8

3 76.2

4 101.6

5 127.0

6 152.4

7 177.8

8 203.2

9 228.6

10 254.0

11 279.4

12 304.8

13 330.2

14 355.6

15 381.0

16 406.4

17 431.8

18 457.2

19 482.6

20 508.0

21 533.4

22 558.8

23 584.2

24 609.6

25 635.0

Metric to Inchesmillimeters Decimal Inches1 .3937

2 .07874

3 .11811

4 .15748

5 .19685

6 .23622

7 .27559

8 .31496

9 .35433

10 .39370

11 .43307

12 .47244

13 .51181

14 .55118

15 .59055

16 .62992

17 .66929

18 .70866

19 .74803

20 .78740

21 .82677

22 .86614

23 .90551

24 .94488

25 .98425

Converting Multipliers

12 inches .03937 mils 1 foot 1 micron

25.4 mm 1,000 microns 1 inch 1 mm

.001 inches 39.37 mils 1 mils 1 mm

25,400 microns .0254 mm 1 inch 1 mils

25.4 microns .0001 cm 1 mils 1 micron

Thickness Conversion Formulas

Inches x 0.0833 = Feet

Inches x 25.4 = mm

Inches x 25,400 = Microns

mils x 25.4 = Microns

mils x 0.001 = Inches

Microns x 0.03937 = mils

Microns x 0.0001 = cm

mm x 1000 = Microns

mm x 39.37 = mils

CUSTOMER INFORMATION PROFILE

Mail to: MACtac or Fax to: MACtac Salesman Name:Credit Dept. Credit Dept. Territory No:4560 Darrow Road (330) 688-5461Stow, OH 44224-1898 (800) 223-3117

Company Name Business Structure:

Any other company name used Proprietorship Partnership Corporation

Billing Address Date Established Federal Tax ID No.

City, State & Zip Code Tax Exempt Yes No Duns No.

Phone No. Fax No.

Owners or OfficersName & Title Social Security Number

If this is a U.S. company and tax exempt, pleasecomplete and return the attached multi-stateExemption/Resale Certificate. In the absence ofan exemption certificate, the law compels us toconsider all sales to you subject to tax.

Home Address Home Phone % Ownership If Corporation: State Incorporated

Name & Title Social Security Number Branch Yes No Subsidiary Division

Home Address Home Phone % Ownership Parent Company

Name & Title Social Security Number Address

Home Address Home Phone % Ownership Address Phone No.

Accounts Payable Manager & Accounts Payable Contact:Name Title Phone No.

Name Title Phone No.

Estimated monthly purchases from MACtac $___________Have our terms of sale been explained to you? Yes No

TERMS AND CONDITIONS:Terms As stated on individual invoice. If the invoice reflects that a discount is available, the payment must be

received by the discount date.

Service charge A charge of 2% per month (24% per annum) is charged on all accounts 15 days or more past due.

Additional fees In the event suit is filed to enforce payment, signer(s) agree to reasonable collection cost and attorneyfees as allowed by law

Returns Restocking charge on all goods returned for credit will be applied.

Please return this application, including financial statement. Be assured that any information provided will be held in strictestconfidence and be used only for our credit granting purposes. Applicants signatures attest financial responsibility, ability andwillingness to pay our invoices in accordance with invoice terms. The above information as well as that on the reverse side isfor the purpose of obtaining credit.

I agree to comply with the above terms, and certify that all information furnished is accurate. I authorize MACtac tocontact creditors, or any credit reporting agency, to obtain ratings now and any time hereafter.

Firm Name _____________________________________

Print name _____________________________________ Title _____________________________

Signed by _____________________________________ Date ________________

Print name _____________________________________ Title _____________________________

Signed by _____________________________________ Date ________________

PLEASE COMPLETE OTHERSIDE OF FORM.

Primary Bank Reference:Bank Contact Officer Phone No. Fax No.

Address City State Zip Code

Loan Type Loan Account # Checking Account # Savings Account #

Primary Supplier References:Name Name

Address Address

City, State & Zip Code City, State & Zip Code

Phone No. Fax No. Phone No. Fax No.

Name Name

Address Address

City, State & Zip Code City, State & Zip Code

Phone No. Fax No. Phone No. Fax No.

Year ________ Year ________ Year ________CURRENT ASSETS:

Cash ___________________ ___________________ ___________________

Accounts receivable ___________________ ___________________ ___________________Inventory ___________________ ___________________ ___________________Other current assets ___________________ ___________________ ___________________

Total ___________________ ___________________ ___________________

FIXED ASSETS:Machinery & equipment ___________________ ___________________ ___________________Land & buildings ___________________ ___________________ ___________________Other fixed assets ___________________ ___________________ ___________________Less depreciation ___________________ ___________________ ___________________

Total ___________________ ___________________ ___________________

CURRENT LIABILITIES: _________________ _________________ _________________Accounts payable ___________________ ___________________ ___________________Short-term loans ___________________ ___________________ ___________________Current portion of long-term debt ___________________ ___________________ ___________________Other current liabilities ___________________ ___________________ ___________________

Total ___________________ ___________________ ___________________

LONG-TERM LIABILITIES:Long-term debt, less current portion ___________________ ___________________ ___________________Other liabilities ___________________ ___________________ ___________________

Total ___________________ ___________________ ___________________

INCOME STATEMENT:Sales less returns and allowances ___________________ ___________________ ___________________

Less cost of goods sold ___________________ ___________________ ___________________Gross Profit ___________________ ___________________ ___________________Less operating expenses ___________________ ___________________ ___________________Operating income ___________________ ___________________ ___________________Less other expenses ___________________ ___________________ ___________________Net income (loss) ___________________ ___________________ ___________________

FIGURES ARE: Audited Unaudited

pg.59


AdditionalInformationOrder Lead Times / Business Rules

SlittingonStockProducts: 5 day lead time if entered and cleared by credit before 4pm EST

FinishedGoods: If stocked, can ship same day if entered and cleared by credit before 1pm EST, otherwise next day ship.

Sheeting: 5 day lead time

CustomProducts: Follow custom lead time

MACtac.comThefollowingitemsareavailableonourwebsite—www.MACtac.com,www.MACtac.com/technical

• Advanced Find - find products using multiple criteria

• PerformanceGuides

• ProductLiterature

• PressReleases

• TechnicalAssistanceBulletins

• FrequentlyAskedQuestions

pg.60

Phone:1-800-328-2619

Packaging&Labeling

Poker Packaging Cradle PackagingPallets will be selected to best match order widths, lengths and volumes.

Pallets will be selected to best match order widths, lengths and volumes.

Chip board / Deck Pads Chip board / Deck Pads

Rolls placed with labels lined up uniformly facing the outside of the length of the pallet.

Rolls placed with labels lined up uniformly facing the outside of the length of the pallet.

Release discs between rolls. Release discs between rolls.

2 x 2 angle board between roll cores. 2 x 2 angle board between roll cores.

Poly Sheet Plastic banded rolls to pallet through 2 x 2 angle boards

Stretch wrap Roll wedges

Pallet label placed on top end of the length side of pallet facing out

Poly sheet

Stretch wrap

Pallet label placed on top end of the length side of pallet facing out.

* Special Requests - Call Customer Service at 1-800-321-0011. Additional charges may apply.

Pallet Options

30” L x 30” W 48” L x 40” W

36” L x 36” W 48” L x 48” W

45” L x 45” W 54” L x 30” W

48” L x 30” W 60” L x 30” W

Carton Packaging Log Roll Carton PackagingPallets will be selected to best match order widths, lengths and volumes.

Pallets will be selected to best match order widths, lengths and volumes.

Chip board / Deck Pads Chip board / Deck Pads

Place poly bag into carton Poly bag each roll

Release paper on bottom and between rolls Upsom pad (fit to carton) with plastic plug (2113) and release disc on each end of the roll

Pilot core between roll cores (must be 2” from top)

May use upsom between layers for stability

Corner board

Polyband to pallet Lay carton down on skid

Stretch wrap Rope and stretch wrap

Pallet label placed on top end of the length side of the pallet. Pallet label placed on top end of the length side of the pallet.


Pallets can contain mixed roll widths. All efforts will be taken to

keep mixed pallets to a minimum.

pg.61

Packaging&Labeling


Shop Order Number

Customer PO#

Customer Order Number

Product

Trace ID

Customer Part Number

Master Roll Stock Lot Number

Upended PackagingPallets will be selected to best match order widths, lengths and volumes.

Lengths and volumes

Upsom board

Roll on end

Upsom board

Wood top

Poly band to pallet / 4 ways

Stretch wrap


pg.62

Phone:1-800-328-2619

pg.63


MACtac TECHNICAL ProductsInnovative Supplier of Engineered Pressure Sensitive Adhesives

MACtac North America • 4560 Darrow Road • Stow, OH 44224-1898 • ph:800.328.2619 • fax:330.688.1153 email: [email protected] • www.MACtac.com/technical

© 2012 Morgan Adhesives CompanyMAC4082 ver. 8 (04/12)MACtac, MACbond, MACfilm andMACmount are trademarks of Morgan Adhesives Company

mactac technical products - nova...

Documents