HD CCTVDigital Video CameraOPERATION MANUAL

Thank you for choosing our high qual i ty camera. Before at tempt ing to connect or operate, p lease read and fol low these instruct ions.

M133-HDX210-001

These servicing instructions are for use by qualified service personnel only.To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Use Class 2 Power Supply Only

CAUTION

2

CONTENTS

1. CAUTIONS

2. IMPORTANT SAFETY INSTRUCTION

3. FEATURES

4. EQUIPMENT AND ACCESSORIES

5. CAMERA COMPONENT DESCRIPTIONS

6. INSTALLATION

7. DIMENSIONS

8. SPECIFICATION

9. OSD MANUAL

3

4

1. CAUTIONSThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.

NoteThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.”

WARNINGThis is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

CautionAny changes or modifications in construction of this devices which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

1. A regulated DC12V 1A power supply is recommended for use with this camera for the best picture and the most stable operation. An unregulated power supply can cause damage to the camera. When unregulated power supply is applied, product warranty will be out of subject.2. It is recommended that the camera is used with a monitor that has a CCTV quality 75 video impedance level. If your monitor is switched to high impedance then please adjust accordingly.3. Do not attempt to disassemble the camera to gain access to the internal components. Refer servicing to your dealer.4. Never face the camera towards the sun or any bright or reflective light, which may cause smear on the picture and possible damage to the CCD.5. Do not remove the serial sticker for the warranty service.6. Do not expose the camera to rain or other types of liquid.7. The apparatus must be connected to a mains socket-outlet with a protective earthing connection.

CAUTIONS

1. CAUTIONS

5

Correct Disposal of This Product(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes purchased this product, or their local government office, for details of where and how they can take item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.Household users should contact either the retailer where they for disposal.

2. IMPORTANT SAFETY INSTRUCTION1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordancewith the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified bythe manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

6

3. FEATURES• High Resolution.

1/3” SONY Progressive Color CMOS Image Sensor,1920 x 1080 60fps

• Support various digital video output.720p30, 720p60, 720p25, 720p50,1080i60, 1080i50,1080p30, 1080p25

• Video Output.Primary HD-SDI (BNC)Test / Setup TV Out (BNC), NTSC / PAL selectable.

• Support RS485 Communucation Protocol for Camera Configuration Remote Control.

• OSD menu for setup and configuration.

• Lens Control.Manual Iris,DC Iris (or Video Iris : factory selectable).

• Provides True Day/Night Capability with Motorized IR Cut Filter.

• Accepts CS Mount LensesAdapter included for C-Mount Lens.

• Power SourceDC 12V / AC 24V

7

4. EQUIPMENT AND ACCESSORIES

HD CCTVDigital Video Camera

AUTO IRIS LENSCONNECTION PLUG

C-MOUNT ADAPTOR RING

OPERATION MANUAL

TERMINAL BLOCK

8

* NOTEPLEASE REMOVE PROTECTION FILM

HDcctv 1.0OUTPUT

AC 24VDC 12V

5. CAMERA COMPONENT DESCRIPTIONS• FRONT

9

TRIPOD MOUNTING HOLE(1/4"-20 UNC)

AUTO IRIS JACK

MOUNT COVER

C-MOUNT ADAPTOR RING(Optional use for C-Mount lens only)

TRIPOD MOUNTING HOLE(1/4"-20 UNC)BACK FOCUS CONTROL LEVER

5. CAMERA COMPONENT DESCRIPTIONS• BACK

①. MENU SET BUTTON

MENU NAVIGATION BUTTONS

②. UP BUTTON

③. DOWN BUTTON

④. LEFT BUTTON

⑤. RIGHT BUTTON

⑥. POWER LED

⑦. SDI OUT BNC

⑧. VIDEO OUT BNC

⑨. MIC IN JACK

⑩. AUDIO OUT JACK (TBD)

⑪. TERMINAL (POWER, RS-485, Digital Input/Output)

10

① ②

③

④

⑤

⑥

⑦

⑧

⑨⑩

⑪

HDcctv 1.0OUTPUT

AC 24VDC 12V

AC 24VDC 12V

11

6. INSTALLATION• LENS CONNECTIONMega Pixel Lenses are sold separately. Lenses such as an auto iris lens, CS-Mount lens and C-Mount lens can be used (adapter included for C-Mount Lens).

NOTE• Please keep the lens clean.• Any foreign objects and Finger marks on the lens can cause inferior image quality in low light level conditions.

When using an auto iris lens

1. Please peel off about 8mm of the outer skin of the auto iris lens cable.

2. Please peel off about 2mm of the outer skin of the insulated conductor inside the lens cable.

12

6. INSTALLATION

3. Please remove the cover of the auto iris lens connection plug and solder the lens cable to the connector pin in the plug.

* PIN ASSIGNMENT OF THE LENS CONNECTOR1) Video auto iris lensPin 1: Power source(DC 12V)Pin 2: N.C(Not used)Pin 3: Video signalPin 4: Shield, GND(Ground)

2) DC auto iris lensPin 1: DAMP-(CTL-)Pin 2: DAMP+(CLT+)Pin 3: DRV+Pin 4: DRV-(GND)

4. Please replace the auto iris lens connection plug cover and take off the sensor protection cap and then attach the auto iris lens to the camera by screwing it in clockwise.

6. INSTALLATION5. Please insert the connection plug from the auto iris lens cable into the auto lens connector, which is located on the side of the camera.

13

C-mount lens : 10mm or less CS-mount lens : 5mm or less

*NOTEWhen using a CS-Mount Lens, you can attach it directly to camera.If using a C-Mount Lens, you must attach the ring spacer provided, otherwise if will crack the image sensor.

6. INSTALLATION

Installation of C-Mount Lens

Installation of CS-Mount Lens

14

C-MOUNT ADAPTOR RING

15

6 . INSTALLATION• MONITOR CONNECTION

DC12V / AC24V REGULATEDPOWER SUPPLY

BNC FEMALEVIDEO

To VIDEO IN

To HD - SDI IN

HDcctv DVRor OtherHDcctv SignalEquipment

Hand - HeldTest Monitor

HDcctv 1.0OUTPUT

AC 24VDC 12V

16

7. DIMENSIONSUnit(mm)

143.5(C-Mount)

138.5(CS-Mount)

AUTO IRIS JACK

MOUNTING HOLE

C-MOUNT ADAPTOR RING(Optional use for C-Mount lens only)

72.5

66

MOUNTING HOLE(1/4"-20 UNC, Depth 5)

8. SPECIFICATIONImage Device SONY 1/3” Progressive Color CMOS Image Sensor

Effective Pixels 2096(H) x 1561(V) 60fps

Unit cell size 2.5um(H) x 2.5um(V)

Video output mode

HD-SDI : 720p30, 720p60, 720p25, 720p50,1080i60, 1080i50,1080p30, 1080p25

TV Out : NTSC / PAL selectable

Minimum illumination 1.0 Lux

S/N Ratio Max 50dB

Shutter speed Auto / Manual selectable

Min. Exposure Time 1/10000 sec

Flickerless Off / 60Hz(50Hz) selectable

True Day/Night IR Cut / Pass Fi l ter change

White Balance ATW / Manual / Speci f ic Color / Push

BLC On / Off (by OSD)

WDR On / Off (by OSD)

Lens Control Manual I r is , DC Ir is (or Video Ir is : factory set t ing only)

Privacy Mask On / Off selectable & Posi t ion controlable each 15 Zone

OSD Menu Yes

PowerConsumption

DC 12V (±10%) Max. 500mAAC 24V (±10%) Max. 6W

Dimension (W x H x D) 72.5mm x 66mm x 138.5mm

Weight 450g

Lens Mount CS / C-mount

Conformi ty CE, FCC, KC, HDcctv Al l iance Base-Line Compl iance

Temperature/Humidity(non-condensing)

Operat ion : -10~50 / 20~80%Storage : -20~70 / 20~95%

Specifications and designs are subject to change for improving the functionality of this product without notice.

17

18

9. OSD MANUAL• Menu structure

- Main Menu

- VIDEO OUT Menu

SYSTEM

VIDEO OUT

LENS

EXPOSURE

WHITE BALANCE

DAY / NIGHT

IMAGE

VIDEO SDI RESOLUTION

SDI FRAME RATE

CDBS FORMAT

VIDEO APPLY

30HZ / 25HZ

NTSC / PAL

30HZ / 25HZ / 60HZ / 50HZ

60HZ / 50HZ

1080P / 1080I / 720P

1080P

720P

1080i

9. OSD MANUAL

- LENS Menu

- EXPOSURE Menuv

19

LENS LENS TYPE

IRIS VOLUME 0 ~ 50

DC IRIS (VIDEO IRIS) / MANUAL IRIS

EXPOSURE SHUTTER

AGC

FLICKERLESS

BRIGHTNESS

BLC

WDR

0 ~ 186

OFF / 50HZ / 60HZ

0 ~ 255

ON / OFF

ON / OFF

SHUTTER MODE

AE PRIORITY

USER MODE

GAIN LEVEL

SHUTTER LEVEL

1 ~ 4

1 ~ 150

1 ~ 160

GAIN LEVEL

SHUTTER LEVEL 1 ~ 160

NORMAL AE / AE HOLD / MANUAL

NORMAL / GAIN / SHUTTER

0 DB / 1.2 DB / 3.31 DB5.12 DB / 6.92 DB / 9.33 DB /

11.14 DB / 12.94 DB / 15.34 DB / 17.16 DB / 18.96 DB / 21.37 DB /

23.18 DB / 24 DB / 27.09 DB / 29.2 DB

NORMAL AE

NORMAL

GAIN

SHUTTER

9. OSD MANUAL

- WHITE BALANCE Menu

- DAY / NIGHT Menu

WHITE BALANCE WB MODE

R GAIN

ATW MODE

0 ~ 255

INDOOR / OUTDOOR

B GAIN

TARGET TEMP

0 ~ 255

1500K / 1567K / 1641K / 1721K /1810K / 1909K / 2019K / 2143K /2283K / 2442K / 2625K / 2838K /3088K / 3387K / 3750K / 4200K /4773K / 5526K / 6563K / 8077K /

10500K / 15000K

ATW / MANUAL / SPECIFIC COLOR / PUSH

ATW

MANUAL

SPECIFICCOLOR

DAY & NIGHT DAY & NIGHT

DAY THRESHOLD

DELAY TIME

NIGHT THRESHOLD

AUTO / BW / COLOR

AUTO

0 ~ 255

0 SEC ~ 10 SEC

0 ~ 255

20

21

9. OSD MANUAL

- IMAGE Menu

IMAGE Y GAMMA

ZONE SELECT

OFF / H FLIP / V FLIP / HV FLIP

C GAMMA

MASK ON / OFF

COLOR

TRANSPARANT

POSITION CONTROL

ZONE 0 ~ ZONE 14

ON / OFF

WHITE / BLACK / RED / GREEN / BLUEYELLOW / CYAN / MAGENTA

0 / 0.5 / 0.75 / 1

0 ~ 1080V SIZE

0 ~ 1920H SIZE

0 ~ 1080V POSITION

0 ~ 1920H POSITION

ON / OFFMOSAIC

GAMMA

SHARPNESS

CONTRAST

SATURATION

DNR

PRIVACY

MIRROR

0 ~31

0 ~ 31

0 ~ 31

OFF / LOW / MIDDLE / HIGH

PRESET 0 ~ PRESET 3

PRESET 0 ~ PRESET 3

22

9. OSD MANUAL

- SYSTEM Menu

SYSTEM FIRMWARE VER

COMMUNICATION CAMERA ID

BAUD RATE

NO. 0 ~ NO.255

2.4K / 4.8K / 9.6K19.2K / 38.4K /57.6K

COMM APPLY

FOCUS MODE

AUDIO MODE

ON / OFF

ENABLE / DISABLE

FACTORY RESET

23

9. OSD MANUAL• Main Menu

- VIDEO : Select SDI out format and TV out format.- LENS : Select the IRIS type and adjust the IRIS control value.- EXPOSURE : Adjust exposure control.- WHITE BALANCE : Adjust white balance control.- DAY / NIGHT : Day & Night control.- IMAGE : Apply image processing effects.- SYSTEM : System information & setting.- EXIT : Close OSD Menu.

MAIN MENU

＋ VIDEO＋ LENS＋ EXPOSURE＋ WHITE BALANCE＋ DAY / NIGHT＋ IMAGE＋ SYSTEM

＊ EXIT

24

9. OSD MANUAL• Video

- SDI RESOLUTIONUse the LEFT/RIGHT button to select the SDI output video resolution - 720p, 1080i, 1080p

* Note : When the OSD menu is not displayed on video, 720p resolution can be selected by pressing the UP button in 5 seconds. Similarly, 1080p resolution can be selected by pressisng the DOWN button in 5 seconds.

- SDI FRAME RATEUse the LEFT/RIGHT button to select the SDI output video frame rate

SDI resolution Available frame rate

1080p 30Hz, 25Hz

1080i 60Hz, 50Hz

720p 30Hz, 25Hz, 60Hz, 50Hz

- CVBS FORMATUse the LEFT/RIGHT button to select the TV out video format - NTSC, PAL* Note : When the OSD menu is not displayed on video, NTSC video format can be selected by pressing the LEFT button. Similarly, PAL video format can be selected by pressing the RIGHT button.

- VIDEO APPLYApply all video setting changed at once. Use the SET button to apply.

- ESCBack to the prevois menu page.

• LENS- LENS TYPEUse the LEFT/RIGHT button to select the lens type for iris control.- DC IRIS(VIDEO IRIS), MANUAL IRIS.

- IRIS VOLUMEUse the LEFT/RIGHT button to adjust the iris volume level.Iris volume control does not apply when the LENS TYPE is set to MANUAL IRIS.

VIDEO OUT

＊ SDI RESOLUTION＊ SDI FRAME RATE＊ CVBS FORMAT

＋ VIDEO APPLY

＊ ESC＊ EXIT

1080p30HZ NTSC

LENS

＊ LENS TYPE＊ IRIS VOLUME

＊ ESC＊ EXIT

DC IRIS25

25

9. OSD MANUAL• EXPOSURE

- SHUTTERUse the SET button to go to the SHUTTER sub menu.

- FLICKERLESSUse the LEFT/RIGHT button to select the flickerless control setting - OFF, 60Hz, 50Hz.

- BRIGHTNESSUse the LEFT/RIGHT button to adjust the brightness reference level.

- AGCUse the LEFT/RIGHT button to adjust the AGC max value

- BLCUse the LEFT/RIGHT button to select ON/OFF the Back-Light Compensation control.

- WDRUse the LEFT/RIGHT button to select ON/OFF the Wide Dynamic Range effect control.

EXPOSURE

＋ SHUTTER＊ FLICKERLESS＊ BRIGHRNESS＊ AGC＊ BLC＊ WDR

＊ ESC＊ EXIT

OFF30

140OFFOFF

26

9. OSD MANUAL• SHUTTER (Sub Menu)

- SHUTTER MODEUse the LEFT/RIGHT button to select shutter & gain control mode- NORMAL AE, AE HOLD, MANUAL.- AE PRIORITYThis menu can be accessed when the SHUTTER MODE is set to NORMAL AE.Use the LEFT/RIGHT button to select the AE control priority setting.- NORMAL, GAIN, SHUTTER.- USER MODEThis menu can be accessed when the SHUTTER MODE is set to MANUAL.Use the LEFT/RIGHT button to select the user mode(1~4) to save setting.- GAIN LEVELIn GAIN priority mode at NORMAL AE mode.This menu can be accessed when the SHUTTER MODE is set toNORMAL AE and AE PRIORITY is set to GAIN.Use the LEFT/RIGHT button to select the Gain value setting.- GAIN LEVELIn MANUAL mode.This menu can be accessed when the SHUTTER MODE is set to MANUAL.Use the LEFT/RIGHT button to select the Gain level setting.- SHUTTER LEVELThis menu can be accessed when the SHUTTER MODE is set to MANUAL.Use the LEFT/RIGHT button to select the Shutter level setting.

SHUTTER

＊ SHUTTER MODE

＊ AE PRIORITY

＊ ESC＊ EXIT

NORMAL AE

NORMAL

SHUTTER

＊ SHUTTER MODE

＊ ESC＊ EXIT

AE HOLD

SHUTTER

＊ SHUTTER MODE

＊ AE PRIORITY

＊ GAIN LEVEL

＊ ESC＊ EXIT

NORMAL AE

GAIN

0 DB

SHUTTER

＊ SHUTTER MODE

＊ USER MODE

＊ GAIN LEVEL＊ SHUTTER LEVEL

＊ ESC＊ EXIT

MANUAL

1

2050

SHUTTER

＊ SHUTTER MODE

＊ AE PRIORITY

＊ SHUTTER LEVEL

＊ ESC＊ EXIT

NORMAL AE

SHUTTER

25

27

9. OSD MANUAL• WHITE BALANCE

- MODEUse the LEFT/RIGHT button to select White balance modes- ATW, MANUAL, SPECIFIC COLOR, PUSH

ATW Auto trace white balance mode

MANUAL Manual white balance mode

SPECIFIC COLOR Manual setting with target color temperature

PUSH White Balance Push mode to Auto AWB

- ATW MODEThis menu can be accessed when the WB MODE is set to ATW.Use the LEFT/RIGHT button to select environment setting. - INDOOR, OUTDOOR - TARGET TEMPThis menu can be accessed when the WB MODE is set to SPECIFIC COLOR.Use the LEFT/RIGHT button to select target color temperature.- R GAINThis menu can be accessed when the WB MODE is set to MANUAL.Use the LEFT/RIGHT button to adjust the Red Gain.- B GAIN This menu can be accessed when the WB MODE is set to MANUAL.Use the LEFT/RIGHT button to adjust the Blue Gain.

WHITE BALANCE

＊ WB MODE

＊ ATW MODE

＊ ESC＊ EXIT

ATW

INDOOR

WHITE BALANCE

＊ WB MODE

＊ R GAIN＊ B GAIN

＊ ESC＊ EXIT

MANUAL

4864

WHITE BALANCE

＊ WB MODE

＊ TARGET TEMP

＊ ESC＊ EXIT

SPECIFIC COLOR

3387K

WHITE BALANCE

＊ WB MODE

＊ ESC＊ EXIT

PUSH

28

9. OSD MANUAL• Day / Night

- DAY & NIGHT:Use the LEFT/RIGHT button to select Day & Night modes - AUTO, EXT, COLOR, BW

AUTO Auto controlled by AGC level in the processor. (AGC Type)

EXT Auto controlled by EXT signal.

COLOR Fixed Day State. Color Image.

BW Fixed Night State. BW Image.

- DELAY TIME:This menu can be accessed when the DAY & NIGHT is set to AUTO.Use the LEFT/RIGHT button to select state change delay time.

- DAY THRESHOLD:This menu can be accessed when the DAY & NIGHT is set to AUTO.Use the LEFT/RIGHT button to select threshold value of change from night state to day state.

- NIGHT THRESHOLD:This menu can be accessed when the DAY & NIGHT is set to AUTO.Use the LEFT/RIGHT button to select threshold value of change from day state to night state.

DAY & NIGHT

＊ DAY & NIGHT

＊ DELAY TIME

＊ DAY THRESHOLD＊ NIGHT THRESHOLD

＊ ESC＊ EXIT

AUTO

3 SEC

101188

DAY & NIGHT

＊ DAY & NIGHT

＊ ESC＊ EXIT

EXT

DAY & NIGHT

＊ DAY & NIGHT

＊ ESC＊ EXIT

COLOR

DAY & NIGHT

＊ DAY & NIGHT

＊ ESC＊ EXIT

BW

9. OSD MANUAL• IMAGE

- GAMMA: Use the SET button to go to the GAMMA sub menu.- SHARPNESS: Use the LEFT/RIGHT button to adjust the sharpness value.- CONTRAST: Use the LEFT/RIGHT button to adjust the contrast value.- SATURATION: Use the LEFT/RIGHT button to adjust the saturation level.- DNR: Use the LEFT/RIGHT button to select the digital noise reduction

level. - OFF, LOW, MIDDLE, HIGH- PRIVACY: Use the SET button to go to the PRIVACY MASK sub menu.- MIRROR: Use the SET button to select image flip modes.

- OFF, H FLIP, V FLIP and H/V FLIP.

• GAMMA (Sub Menu)

- Y GAMMA: Use the LEFT/RIGHT button to select preset gamma setting for luma.

- C GAMMA: Use the LEFT/RIGHT button to select preset gamma setting for chroma.

29

IMAGE

＋ GAMMA＊ SHARPNESS＊ CONTRAST＊ SATURATION＊ DNR＋ PRIVACY＊ MIRROR

＊ ESC＊ EXIT

71718

OFF

OFF

GAMMA

＊ Y GAMMA＊ C GAMMA

＊ ESC＊ EXIT

RPESET 2RPESET 3

9. OSD MANUAL• PRIVACY MASK (Sub Menu)

- ZONE SELECT: Use the LEFT/RIGHT button to select the mask zone number to setting.

- MASK ON/OFF: Use the LEFT/RIGHT button to select ON/OFF the mask that is zone selected.

- TRANSPARENT: Use the LEFT/RIGHT button to adjust the mask transparent level.

- COLOR: Use the LEFT/RIGHT button to select the mask color.- POSITION CONTROL: Use the SET button to go to the mask position setting sub

menu

• PRIVACY MASK (Sub Menu)

- V SIZE: Use the LEFT/RIGHT button to adjust the mask vertical size.- H SIZE: Use the LEFT/RIGHT button to adjust the mask horizontal size.- V POSITION: Use the LEFT/RIGHT button to adjust the mask vertical position.- H POSITION: Use the LEFT/RIGHT button to adjust the mask horizontal position.- MOSAIC: Use the LEFT/RIGHT button to select ON/OFF the mask mosaic

setting.

PRIVACY MASK

＊ ZONE SELECT＊ MASK ON / OFF＊ TRANSPARANT＊ COLOR

＋ POSITION CONTROL

＊ ESC＊ EXIT

ZONE 0OFF

0.5WHITE

PRIVACY MASK

＊ V SIZE＊ H SIZE＊ V POSITION＊ H POSITION＊ MOSAIC

＊ ESC＊ EXIT

0000

OFF

30

31

9. OSD MANUAL• SYSTEM

- FIRMWARE VER : Information of camera’s firmware version.

- COMMUNICATION: Use the SET button to go to the COMMUNICATION sub menu.

- AUDIO OUTPUT: Use the LEFT/RIGHT button to select the audio output ENABLE/DISABLE.

- FOCUS MODE: Use the LEFT/RIGHT button to select ON/OFF the Focus mode. In Focus mode, the iris becomes fully open, electronic shutter controls the light level, and the TV out screen zooms into the center in order to make focusing easier. When in Focus Mode, the OSD menu is not displayed.

- FACTORY RESET: Use the SET button to action start of reset. Clear all setting and initialize to factory setting.

• COMMUNICATION (Sub Manu)- CAMERA ID : Use the LEFT/RIGHT button

to select the RS485 ID Address.

- BAUD RATE : Use the LEFT/RIGHT button to select the baudrate setting for RS485 communication.

- COMM APPLY : Apply all communication setting changed at once. Use the SET button to apply.

• EXITThis menu can be accessed when use the EXIT action in all menu pages.

- SAVE & EXIT SETUP:Save all current setting and Close OSD menu. These setting are loaded and applied automatically when the Camera is power on.- EXIT WITHOUT SAVING:

Close OSD menu. Camera’s current setting is not saved. Use the SET button to action.

SYSTEM

＊ FIRMWARE＊ COMMUNICATION＊ AUDIO OUTPUT＊ FOCUS MODE＊ FACTORY RESET

＊ ESC＊ EXIT

0.2B.25

DISABLEOFF

COMMUNICATION

＊ CAMERA ID＊ BAUD RATE

＊ COMM APPLY

＊ ESC＊ EXIT

NO. 12.4K

SAVE & EXIT SETUPEXIT WITHOUT SAVING

Quick Setup Guide(HD CCTV CAMERA)

■ OSD Menu Button.

- Video out Format Change (NTSC/PAL Selection)Default(Factory default setting) video out format is NTSC.Camera power on & Until push the SET button(While OSD menu is not displayed on video), Can select NTSC/PAL video format output on VIDEO port - Push the LEFT button to select NTSC format video out mode or Push the RIGHT button to select PAL format video out mode.

*Warning : When HD-SDI out format is setted 1080P, NTSC/PAL video out is not supported. While OSD menu is not displayed on video, Can select 1080P/720P format output on HD-SDI port - Push the UP button in 3 seconds to select 720P format video out or Push the DOWN button in 3 seconds to select 1080p format video out.

- OSD menu Display on VideoPush the SET button.

- Use the Focus modeCan be found in SYSTEM menu section in OSD menu.Use the LEFT/RIGHT button to select ON/OFF the Focus mode.

·Video output port- HDcctv 1.0 OUTPUT (BNC) :

HD-SDI video out to HDcctv DVR or Other HDcctv Signal Equipment.- VIDEO (BNC) :

NTSC or PAL video out to Hand-Held Test Equipment(TV Monitor).

·Focus ModeIn the Focus mode, the Iris becomes fully open and the TV out screen zooms into the center in order to make focusing easier.When turn on the Focus mode, the OSD menu display in turned off automatically and when turn off the focus mode, the OSD menu display is back.

UP / 720p

DOWN / 1080p

LEFT / NTSC RIGHT / PAL