ltp 61 shut-off nutrunner uk
TRANSCRIPT
LTP 61 Shut-off Nutrunner Not only accurate, but also very fast
2
Some joints are more critical than others. If you need
a higher level of accuracy in your work, take a look at
Atlas Copco’s shut-off nutrunners.
They have become standard pieces of equipment
at truck manufacturers such as Scania and Volvo.
And are becoming more and more common in
service workshops. Why?
How important is accurate tightening for your customers?
The same torque time after time
A shut-off nutrunner is a reliable tool. You decide what torque you want – anything from 60 - 4 000 Nm depending on the model – and that’s what you get. No more, no less. Even in soft joints. And as the name suggests, it shuts off at the torque you have selected. So you get the same accu-rate result time after time – regardless of the opera-tor and their level of experience. A clear shut-off signal tells operators when the tightening cycle is fi nished. Not only does this
ensure high accuracy, but it also boosts productivity because the operator can immediately move on to the next bolt without having to spend time checking to see if the bolt needs tightening a little more.
First the bad news
A shut-off nutrunner gives you reliable tightening because of the way it builds up torque in a smooth, controlled and continuous way. This produces excellent quality in the tightening phase. However, with a standard shut-off nutrunner,
3
The Multi-Torque Selector allows you to preset four different torque levels per tool.
Adju
stable torque ran
ge
this controlled action slows things down during the rundown phase.
Now for the good news
Ever changed a wheel? First you spin the wrench, then tighten slowly with both hands. Two-speed tightening. That’s what you get with the LTP 61 – the market’s only nutrunner with two motors. One for rundown. One for tightening. If you want to know how this can boost productivity, turn the page.
4
Ten times faster rundown
A conventional, mid-size, shut-off nutrunner works at around 20 rpm, during both rundown and tightening. A mid-range LTP 61 runs down at 210 rpm – that’s 10 times faster. If you have a large number of nuts to tighten, the LTP 61 will save you a considerable amount of time, boosting the productivity of your company. Chances are, it will pay for itself within months.
How important is productivity for your company?
With the LTP 61, you don’t have to compromise: you
get highly accurate tightening and high productivity.
The secret is two motors. One high speed motor for
fast rundown. And one high torque motor for reliable
tightening.
The fastest tool on the market just got faster
Twin motors might sound simple. But you won’t fi nd another nutrunner like the LTP 61 on the market. Its predecessor, the LTP 51, has been winning over fans for over twenty years. In some indus-tries, such as truck and bus manufacturing, it has become an accepted standard.
5
The new LTP 61 is as accurate as its predeces-sor, but it is faster. Twice as fast in rundown. And yet the new range is only marginally heav-ier than the existing one. When we say that Atlas Copco stands for “innovation, commitment and interaction” we really mean it.
Run-down speed is up to ten times higher compared with a single-motor nutrunner.
Time
LTP 61
LTP 51
Single-motor
6
How important is ergonomics at your workplace?
Shut-off nutrunners are quite in operations and vibration
levels are low. Operators who progress from impact
wrenches really appreciate the difference.
Very quiet
But how quiet is the LTP 61? A shut-off nutrunner builds up torque continuously, without interruption. In other words, there is no noise generated by the actual process. Sound levels are also kept low because all exhaust air is piped through the handle into a hose, minimizing noise from the pneumatic system.
Low vibration levels
The LTP 61 has low vibration level because torque is
transferred continuously. Compare this to an impact wrench in which torque is produced by a rotating metal hammer slamming into the output shaft.
Minimize strain on wrists and arms
Wrist and arm strain is kept to a minimum with shut-off nutrunners because the reaction force is handled by a torque-reaction bar. Our unique, innovative reac-tion bars are easy to use to keep productivity levels high.
Single-handed operation
The LTP 61 is light, compact and well-balanced and so can be used with just one hand. The rubber pistol grip has been ergonomically optimized for maximum operator comfort.
Increasing output at Volvo Trucks
“With output being ramped up every year, productivity is getting more and more important,” says Dennis Johansson, Process Engineer at Volvo Trucks in southern Sweden. Volvo Trucks is already using more than 200 LTP 51 shut-off nutrunners on axle and chassis assembly lines. “The Atlas Copco machines are reliable and they give us the accurate torque that we need,” says Dennis.
Perfect for long run-downs
Producing over 26,000 units every year, the need to shave off a few seconds here, a few seconds there is a pressing matter. “The LTP 61 is that much faster, ”says Dennis, “so it’s perfect for long run-downs. We expect to see more LTP 61s turning up on the production lines in the near future.”
7
8
How many tools do you really need in your workshop?
A shut-off nutrunner is a sophisticated tool. But for
many workshops it has not been economically viable
to own an advanced wrench that performs just one
dedicated task. However, with three simple accessories,
you can use one LTP 61 for dozens of different jobs.
And that means a sophisticated tool has now become
a very economical one too.
Multi-Torque Selector
Transform one nutrunner into four: the Multi-Torque Selector allows you to preset four different torque levels per tool. Order ready-mounted or as an acces-sory to existing LTP 51 and 61 nutrunners.
Multi-Point Reaction Bar
In many workshops, an application that requires a different torque also requires a different reaction point. The Multi-Point Reaction Bar features a sliding
bracket that gives you a number of different reaction points.
S-Bar – straight out of the box
A blank reaction bar has to be bent, cut or welded – an extra “to do”. The geometry of the S-Bar has been optimized to provide a maximum number of reaction points. This means you’ll be able to use the S-Bar in about 70-80 percent of all applications straight out of the box.
9
From 60-4 000 Nm
With a range consisting of 11 different tool sizes, there is an LTP 61 to suit all kinds of applications. The smallest model weighs just 2.6 kg and delivers 60 Nm, while the largest version supplies 4 000 Nm.
LTP 61 – accurate, fast and ergonomic
Increase tightening accuracyWith automatic shut-off you get a high level of tightening precision, even in soft joints. This helps increase productivity since the operator gets a clear shut-off signal when tightening is completed.
Boost productivityUnique twin-motor drive: one for high speed rundown, the other for high precision tightening.
Single-handed operationBecause the LTP 61 is light, compact and well-balanced, it can be used with just one hand.
Optimized S-BarA blank reaction bar has to be bent, cut or welded. The S-Bar has been optimized for use in 70-80 percent of all applications straight out of the box.
One reaction bar, dozens of jobsThe Multi-Point Reaction Bar features a sliding bracket that gives you a number of different reaction points for different applications.
Now easier to run in reverseUnlike its predecessor, the LTP 61 runs in reverse and stays in reverse until you change the setting. Thanks to a new mode selection, you can now hold the tool with just one hand, whatever direction you run the machine.
10
Adju
stable torque ran
ge
Twice as fast as the LTP 51Thanks to the new motors, the rundown speed has been doubled in comparison with its predecessor.
Virtually silent and vibration-freeShut-off nutrunners generate no process noise. And by building up torque continuously, they are much quieter than impact wrenches.
Multi-torque for multi-taskingWith this easy-to-mount selector, you transform one nutrunner into four. The Multi-Torque Selector allows you to preset four different torque levels per tool.
From 60-4 000 NmWith a range consisting of 11 different tool sizes, there is an LTP 61 to suit your needs. The smallest model weighs just 2.6 kg and delivers 60 Nm, while the largest supplies 4 000 Nm. Stall versions, designated LMP 61, are also available.
11
Technical data
Air con- Air
Bolt Square Torque range Min torque Free CS sumption at inlet
size drive at 6.3 bar at 3 bar speed Weight Length distance free speed thread Spline
Model mm in Nm ft lb Nm ft lb r/min kg lb mm mm l/s cfm in type Ordering No.
Non reversible
LTP61 H100-13 M12 1/2 55-100 40-75 45 35 1800 3.0 6.6 223 29 20 42 3/8 3 8431 0800 07LTP61 H170-13 M14 1/2 95-170 70-125 70 50 1100 3.0 6.6 223 29 20 42 3/8 3 8431 0800 14LTP61 H230-19 M16 3/4 125-230 90-170 85 60 820 3.0 6.6 223 29 20 42 3/8 3 8431 0800 21LTP61 H350-20 M18 3/4 190-350 140-255 145 105 520 3.9 8.6 260 31 20 42 3/8 4 8431 0800 28LTP61 H500-20 M20 3/4 275-500 200-370 220 160 360 3.9 8.6 260 31 20 42 3/8 4 8431 0800 35LTP61 H700-25 M22 1 360-650 265-480 280 207 280 4.5 9.9 305 34 20 42 3/8 5 8431 0800 42LTP61 H900-25 M24 1 480-870 350-640 300 220 210 4.5 9.9 282 32 20 42 3/8 5 8431 0800 49LTP61 H1500-25 M30 1 850-1500 625-1100 700 516 115 6.8 14.5 323 42 20 42 3/8 9 8431 0800 56LTP61 H1900-38 M30 1 1/2 1050-1900 770-1400 800 576 90 14.1 31.0 380 68 20 42 3/8 8 8431 0800 63LTP61 H2800-38 M36 1 1/2 1550-2800 1140-2060 1200 864 65 14.1 31.0 380 68 20 42 3/8 8 8431 0800 70LTP61 H3800-38 M42 1 1/2 2100-3800 1540-2790 1600 1152 50 14.1 31.0 380 68 20 42 3/8 8 8431 0800 77
Reversible LTP61 HR100-13 M12 1/2 55-100 40-75 45 35 1800 3.0 6.6 235 30 20 42 3/8 3 8431 0801 08LTP61 HR170-13 M14 1/2 95-170 70-125 70 50 1100 3.0 6.6 238 30 20 42 3/8 3 8431 0801 15LTP61 HR230-19 M16 3/4 125-230 90-170 85 60 820 3.0 6.6 275 34 20 42 3/8 3 8431 0801 22LTP61 HR350-20 M18 3/4 190-350 140-255 145 105 520 3.9 8.6 275 34 20 42 3/8 4 8431 0801 29LTP61 HR500-20 M20 3/4 275-500 200-370 220 160 360 3.9 8.6 275 34 20 42 3/8 4 8431 0801 36LTP61 HR700-25 M22 1 360-650 265-480 280 207 280 4.5 9.9 305 34 20 42 3/8 5 8431 0801 43LTP61 HR900-25 M24 1 480-870 350-640 300 220 210 4.5 9.9 305 34 20 42 3/8 5 8431 0801 50LTP61 HR1500-25 M30 1 850-1500 625-1100 700 516 115 6.8 14.5 345 42 20 42 3/8 9 8431 0801 57LTP61 HR1900-38 M30 1 1/2 1050-1900 770-1400 800 576 90 14.1 31.0 380 68 20 42 3/8 8 8431 0801 64LTP61 HR2800-38 M36 1 1/2 1550-2800 1140-2060 1200 864 65 14.1 31.0 380 68 20 42 3/8 8 8431 0801 71LTP61 HR3800-38 M42 1 1/2 2100-3800 1540-2790 1600 1152 50 14.1 31.0 380 68 20 42 3/8 8 8431 0801 78
Air con- Air
Bolt Square Torque range Min torque Free CS sumption at inlet
size drive at 6.3 bar at 3 bar speed Weight Length distance free speed thread Spline
Model mm in Nm ft lb Nm ft lb r/min kg lb mm mm l/s cfm in type Ordering No.
Equipped with Multi Torque unit
LTP61 HR100-13-MT M12 1/2 55-100 40-75 45 35 1800 3.3 7.3 288 30 20 42 3/8 3 8431 0806 02LTP61 HR170-13-MT M14 1/2 95-170 70-125 70 50 1100 3.3 7.3 288 30 20 42 3/8 3 8431 0806 09LTP61 HR230-19-MT M16 3/4 125-230 90-170 85 60 820 3.3 7.3 288 34 20 42 3/8 4 8431 0806 16LTP61 HR350-20-MT M18 3/4 190-350 140-255 145 105 520 4.2 9.2 325 34 20 42 3/8 4 8431 0806 23LTP61 HR500-20-MT M20 3/4 275-500 200-370 220 160 360 4.2 9.2 325 34 20 42 3/8 4 8431 0806 30LTP61 HR700-25-MT M22 1 360-650 265-480 280 207 280 4.8 10.6 355 34 20 42 3/8 5 8431 0806 33 LTP61 HR900-25-MT M24 1 480-870 350-640 300 220 210 4.8 10.6 355 34 20 42 3/8 5 8431 0806 37LTP61 HR1500-25-MT M30 1 850-1500 625-1100 700 516 115 7.1 15.6 395 42 20 42 3/8 9 8431 0806 44LTP61 HR1900-38-MT M30 1 1/2 1050-1900 770-1400 800 576 90 14.4 31.7 430 68 20 42 3/8 8 8431 0806 51LTP61 HR2800-38-MT M36 1 1/2 1550-2800 1140-2060 1200 864 65 14.4 31.7 430 68 20 42 3/8 8 8431 0806 58LTP61 HR3800-38-MT M42 1 1/2 2100-3800 1540-2790 1600 1152 50 14.4 31.7 430 68 20 42 3/8 8 8431 0806 65
Weight excluding reaction bar . Recommended hose size 13 mm for hose length up to 5 m.
Weight excluding reaction bar . Recommended hose size 13 mm for hose lenght up to 5 m.
Modell
Hose nippleSwivelling type MultiFlex connector (3/8’’ BSP)Exhaust hoseProtective cover for 61 standard (transparent)Protective cover for 61 Multi-torque (transparent)Multi torque selector for LTP 61Quick change retainer, 1/2” square modelsQuick change retainer, 3/4” square modelsQuick change retainer, 1” square models
Bestell-Nr.
9000 0242 008202 1350 224210 2201 004210 4672 004210 4672 014210 4636 954250 1190 004210 3476 804210 3524 80
LTP 61 H/HR accessories
Protective cover
Multi torque selectorMultiFlex connector, swivelling type
13
Installation Proposal
ErgoQIC 10 ErgoNIP 10
8202 1180 79*
5 m CABLAIR 13
ErgoQIC 10 ErgoNIP 10 10 m CABLAIR 16
Ball Valve +MIDI F/RD 15 +ErgoQIC 108202 0829 11
Ball Valve +MIDI FR 15 +DOS 15B8202 0845 67
8202 1180 79
8202 1182 00
Nipple 1/2’’ BSP 10 m CABLAIR 16 ErgoQIC 10 ErgoNIP 10 M10
ErgoNIP 10 5 m CABLAIR 13 ErgoQIC 10 ErgoNip 10 M10
Modell
Mounting dia Ø54mm
H 100-13H 170-13H 230-19H 350-20H 500-20H 700-25H 900-25Mounting dia Ø60mm
HR 100-13HR 170-13HR 230-19Mounting dia Ø63.5mm
H 1900-38H 2800-38H 3800-38Mounting dia Ø67mm
HR 350-20HR 500-20HR 700-25HR 900-25HR 1900-38HR 2800-38HR 3800-38Mounting dia Ø83.5mm
H 1500-25HR 1500-25
Bestell-Nr.
4210 3088 80
4210 3088 84
4210 3088 83
4210 3088 82
4210 3088 81
Swivelling suspension yokes for LTP 61
Modell
Aluminium, max torque 175Nm, spline 3Square braket, spline 3Square braket, spline 4Square braket, spline 5Square braket, spline 9S-type, spline 3S-type, spline 4S-type, spline 5S-type, spline 9Sliding drive type (short), spline 3Sliding drive type (short), spline 3Sliding drive type (short), spline 4Sliding drive type (short), spline 5Sliding drive type (short), spline 9Sliding drive type (long), spline 4Sliding drive type (long), spline 5Extended sliding rectionbar, quick change att., spline 5 Specially designed for truck rear wheel tightening
L=400mm50 x 100 x 12 mm65 x 125 x 16 mm65 x 125 x 16 mm85 x 150 x 20 mm
––––
1/2” square drive3/4” square drive3/4” square drive1” square drive1” square drive3/4” square drive1” square drive1” square drive
–––––––––
C-C 70-120mmC-C 70-120mmC-C 76-126mmC-C 80-125mmC-C 80-130mmC-C 82-218mmC-C 82-218mmC-C 68-112mm
Bestell-Nr.
4210 2219 014210 2219 034210 2183 014210 2726 014210 3899 004210 4480 034210 4480 044210 4480 054210 4480 094210 4481 834210 4481 634210 4481 844210 4481 854210 4481 894210 4616 844210 4616 854210 4498 80
Reaction bars
Modell
Trigger kitGeneral service kit
Bestell-Nr.
4081 2190 904081 0397 90
Service kits
Bracket
S type
Extended sliding reaction bar
Sliding drive, no drive, long and short
Sliding drive type, long
Sliding drive type, short
Suspension yoke
www.atlascopco.com
9833
185
9 01
E.C
.O R
ekla
mb
yrå
AB
. Ått
a.45
Try
cker
i AB
200
8:1