lps construction manual - part 2

8/16/2019 Lps Construction Manual - Part 2

1/629

CONSTRUCTION MANUAL

PART 2

Technical Specifications and StandardsRevised December 15, 2014

Original Issue Date: February 9, 1990

Previous Revisions

August 30, 2005December 17, 2004

October 8, 2004

October 28, 2003

October 3, 2002

November 1, 2001

February 20, 1998

April 15, 1996

March 10, 1994

January 15, 1992

April 16, 1991


2/629

LPS CONSTRUCTION MANUAL December 2014

Introduction to Guideline Specifications

The LPS Guideline Specifications provide general direction to Architects and other Consultants forthe design and specification of District facilities and facility improvements. They also identify forprospective vendors and contractors products and equipment pre-approved for conformance to

District standards and expectations. They are intended to promote consistent quality and reasonablecontinuity in products, materials, systems and workmanship for all District facilities; they are notintended to limit creative design or functional problem-solving. The Guidelines are not sufficientlycomplete to serve as buildable technical specifications, but any proposed deviation from them willrequire consultation with and acceptance by the LPS Operations and Maintenance Department.Consultants also will be responsible for informing the District of any conflict found between theGuidelines and current codes, standards or best practices.

Introduction to Model Specifications & Technology Standards

The LPS Model Specifications provide more detailed definition of District construction standards andprocedures for consultants and contractors, based upon cumulative District experience with facilitydesign, maintenance and operations. Each section is intended to serve as a model for buildabletechnical specifications, typically requiring customization to address conditions, needs andapplications for specific projects at particular facilities through detailed collaboration betweenconsultants and LPS managers, technicians and users. Identification of technical requirements orprohibitions, pre-approved manufacturers, and preferred products or models is intended to optimizelong-term value to the District and its facilities, balancing innovation and competitive first-cost withmanageable standardization and sustainable life-cycle costing.

The LPS Technology Standards provide definitive goals, design and installation mandates anddetailed specifications for District facilities infrastructure and devices supporting InformationTechnology, Domestic and Emergency Communications, Smoke/Fire Detection and Alarm, and

Building Access and Security. The Standards identify professional certifications for designengineers, manufacturer certifications for installers, and relevant experience required for both.Proprietary platforms are identified for each major system, along with pre-approved providers ofmutually compatible component devices. Deviation from any provision in these Standards isprohibited except for unique circumstances and only following exhaustive review and sign-off by theLPS Operations and Maintenance Department, Information and Technology Services and/or Securityand Emergency Planning, as appropriate.


3/629

LPS MODEL SPECIFICATIONS December 2014

LPSCM Model Specifications Index - 1

INDEX – PART 2

DIVISION 07 – THERMAL AND MOISTURE PROTECTION07 01 50 Preparation for Reroofing07 22 00 Roof and Deck Insulation Boards & Associated Accessories07 22 10 Roof Insulation

07 54 10 Adhered Thermoplastic Membrane Roofing07 61 00 Metal Roofing07 62 00 Flashing and Sheet Metal Trim07 80 00 Fire and Smoke Seals

DIVISION 08 – DOORS AND WINDOWS08 54 00 Fiberglass Windows

DIVISION 20 – BASIC MECHANICAL20 05 18 Mechanical Systems Fire-Stopping

DIVISION 21 – FIRE SUPPRESSION21 10 00 Water Based Fire Protection

21 30 00 Fire Pumps

DIVISION 22 – PLUMBING22 11 00 Water Distribution Piping 22 11 23 Plumbing Pumps22 12 00 Storage Tanks22 13 00 Drainage and Vent Systems22 13 23 Interceptors22 31 00 Water Treatment22 34 00 Water Heaters22 42 00 Plumbing Fixtures and Trim22 66 00 Laboratory Drainage Systems

DIVISION 23 – HEATING, VENTILATING AND AIR CONDITIONING23 05 00 Basic Mechanical Requirements23 05 13 Motors, Starters and Drives23 05 16 Pipe Expansion Joints and Fittings23 05 19 Meters and Gauges23 05 23 Valves23 05 29 Supports and Anchors23 05 48 Vibration Control23 05 53 Mechanical Identification23 05 93 Testing, Adjusting and Balancing23 07 00 Mechanical Insulation23 08 00 Mechanical Commissioning23 09 23 Direct Digital Control Systems23 09 93 Sequence of Operations

23 20 00 Basic Piping Materials and Methods23 21 00 Hydronic Specialties23 21 13.13a Underground Piping for Systems Below 250 F23 21 13.13b Underground Piping for Class A Soils23 21 16 Piping Specialties23 21 23 Hydronic Pumps23 23 00 Glycol Systems23 23 16 Refrigerant Piping Specialties23 25 00 Water Treatment23 31 13 Metal Ductwork


4/629


LPSCM Model Specifications Index - 2

23 33 00 Ductwork Accessories23 33 19 Ductwork Sound Attenuation23 34 00 Air Handling Fans23 36 00 Air Terminals23 37 13 Air Distribution Devices23 51 00 Breechings, Chimneys and Stacks23 52 00 Boilers23 53 00 Boiler Accessories23 54 00 Forced Air Furnaces23 62 00 Condensing Units23 63 13 Air Cooled Condensers23 64 16.13 Centrifugal Chillers - Air Cooled23 64 16.16 Centrifugal Chillers - Water Cooled23 64 19 Reciprocating/Scroll Chillers 23 65 00 Cooling Towers23 73 00 Packaged Indoor HVAC Units 23 74 00 Packaged Rooftop HVAC Units23 75 13 Air Handling Units23 81 23 Computer Room Air Conditioning Units23 82 00 Terminal Units

23 83 13 Electric Heating Cables


5/629


LPSCM 07 01 50 - 1

SECTION 07 01 50 – PREPARATION FOR REROOFING

PART 1 – GENERAL

1 .1 SECTION INCLUDES:

A. Required demolition for reroofing work.

B. Required renovation for reroofing work.

1 .2 RELATED SECTIONS:

A. Use of site – LPS General Conditions of the Contract.

B. Alterations project procedures – LPS General Conditions of the Contract.

C. Section 07 22 00 – Roof and Deck Insulation Boards and Roof Accessories

D. Section 07 54 10 – Adhered Thermoplastic Membrane Roofing

1 .3 SUBMITTALS:

A. Product Data: Submit manufacturer's product data sheets for each product in accordancewith the LPS General Conditions of the Contract and Division 07.

1 .4 PROTECTIONS:

A. Prior to starting minor demolition operations, provide necessary protections as specified inthe LPS General Conditions of the Contract and Division 07.

1 .5 COORDINATION:

A. Sequence minor demolition and renovation with work sequence of reroofing work.

B. Coordinate with reroofing work so that no more existing roofing and sheet metal items areremoved in one day than can be replaced along with new roofing work in same day.

PART 2 – PRODUCTS

2 .1 MATERIALS

A. Wood Nailers and Blocking: Utility grade lumber, any commercial softwood species, kilndried and preservative treated.

B. Fasteners:

1. Screws: Fluorocarbon coated screws, i.e. Roofgrip Climaseal™.

2. Nails: Nonferrous, cement-coated, or hot-dip galvanized ring-shank nails.

3. Concrete and Masonry: Stainless steel or galvanized screws with lead expansionanchor, Rawlplug by the Rawlplug Co.

C. Concrete Splash Blocks: Precast concrete, minimum 3000 psi strength, 18 in. x 30 in. size,with water channel.


6/629


LPSCM 07 01 50 - 2

2 .2 Gas Pipe Supports: Furnish and install Miro Industries gas pipe supports Model Numbers 4-RAH-HDG or 6-RAH-HDG (hot dipped galvanized), size as required for gas pipe on roof.

2 .3 Electrical Conduit Supports: Miro Industries electrical conduit supports Model Numbers CS-4-RAH-HDG or CS-6-RAH-HDG (hot dipped galvanized), size as required for electrical conduit onroof. All electrical conduits are to be clamped per NEC requirements.

A. Miro Industries Pillow Block Pipe Stands Model 1.5 with 1.5 Spacer (for electrical conduits3" or less above finished roof height).

PART 3 – EXECUTION

3 .1 PREPARATION:

A. Verify that required barricades and other protective measures are in place.

3 .2 MINOR DEMOLITION OPERATIONS:

A. GENERAL:

1. Comply with precautions and procedures specified in Division One and Seven.

2. Cut and remove materials as designated on Drawings.

3. Execute demolition in a careful and orderly manner with least possible disturbanceor damage to adjoining surfaces and structure.

4. Avoid excessive vibrations in demolition procedures that would be transmittedthrough existing structure and finish materials.

B. ABANDONED EQUIPMENT SUPPORTS AND VENTS:

1. Completely remove abandoned supports.

2. Remove abandoned piping and vent penetrations, electrical conduit and switchgear. Cap-off at roof deck level.

C. PITCH PANS:

1. Remove existing pitch pans and wood blocking supporting piping.

2. Remove existing pitch pans at conduit and pipe penetrations.

3. Remove existing pitch pans and wood blocking supporting at mechanicalequipment.

D. ABANDONED CURBS/EQUIPMENT DEMOLITION:

1. Completely remove existing abandoned curbs and/or equipment. Remove curbs todeck level, and patch hole in roof deck to match existing roof deck.

3 .3 DISPOSAL:

A. Unless specifically noted otherwise, materials, equipment and debris resulting fromdemolition operations shall become property of Contractor. Remove demolition debris inaccordance with applicable City, State and Federal laws, and in accordance withrequirements of Division One.

B. Legally dispose of demolition debris.

3 .4 SALVAGE:

A. Salvage following existing items for reconditioning and reuse:


7/629


LPSCM 07 01 50 - 3

1. Existing ductwork and supports to remain. Modify duct support legs to allow foruse with new roof system (where applicable).

3 .5 MINOR RENOVATION WORK:

A. Replacing wood nailers and curbs; new wood nailers and curbs:

1. Clean and prepare existing surfaces to receive wood nailers and curbs.2. Replace designated wood blocking with new wood blocking.

3. Install wood nailers and curbs continuously without gaps and plumb, level and truewith joints flush. Securely fasten to structure with expansion fasteners and toexisting wood with Fluorocarbon or epoxy coated screws, at a rate of 12" o.c.

B. Equipment Reinstallation:

1. Remove and reinstall existing equipment, HVAC units, and fans as required tofacilitate installation of new roofing and flashing. All HVAC units are to be lifted offthe curb to allow new roof membrane to run over the top of the roof curb.

2. Carefully disconnect equipment and move in a manner to prevent damage to

equipment or service lines.

3. Coordinate reinstallation with new equipment support curbs where scheduled.

4. Reinstall equipment on curbs and supports after new flashing is installed. Securelyfasten to curbs.

5. Extend and reconnect electrical connections, gas piping and drain lines.

6. Disconnecting, extending and reconnecting of services shall be performed by amechanical, plumbing and electrical company licensed to perform such work.

7. Equipment shall be left in complete operating condition.

C. Relocating and Raising Piping and Conduit:

1. Raise existing gas piping, conduit and condensate drain lines where scheduledand where required for new curbs and supports.

2. Disconnect gas piping and extend with new piping and fittings.

3. Extend conduit with proper conduit connections and fittings. Extend wiring asrequired for additional conduit.

4. Gas Pipe Supports: Furnish and install Miro Industries gas pipe supports ModelNumbers 4-RAH or 6-RAH (hot dipped galvanized) (size as required for gas pipeon roof) per governing local codes and manufacturer requirements and/or spaceda minimum of 10' o.c and at all corners (whichever is more stringent). Install overan extra layer of specified walkway pad.

5. Electrical Conduit Supports: Furnish and install Miro Industries electrical conduitsupports Model Numbers 4-RAH or 6-RAH (hot dipped galvanized) (size asrequired for electrical conduit on roof) per governing local codes and manufacturerrequirements and/or spaced a minimum of 10' o.c and at all corners (whichever ismore stringent). All electrical conduits are to be clamped per NEC requirements.Install over an extra layer of specified walkway pad. Furnish and install MiroIndustries Pillow Block Pipe Stands Model 1.5 with 1.5 Spacer (for electricalconduits 3" or less above finished roof height).

D. Testing and inspection:


8/629


LPSCM 07 01 50 - 4

1. Test electrical circuits for proper operation.

2. Test drain piping for leaks and proper flow.

3. Perform tests and inspections on gas piping as required by City. Gas pipingsystems shall be left complete and operational with City inspection "green tags" atcompletion of work.

4. Test equipment that was removed and reinstalled to ensure that equipment isoperating properly.

E. Roof Drain Repair:

1. Replace any missing/broken drain parts (i.e. clamping ring/bolts, etc.) with new tomatch existing.

2. Replace missing, broken, and plastic drain strainers with new steel drain strainersto match existing.

3. Clean existing drain bowl, parts, etc. and prime and paint (2 coats) all drain partswith Full Gloss, Alky Enamel: Two coats over rust inhibitive primer, S-W: SWPGloss Oil.

END OF SECTION 07 01 50


9/629


LPSCM 07 22 00 - 1

07 22 00 – ROOF AND DECK INSULATION BOARDS & ASSOCIATED ACCESSORIES

PART 1 – GENERAL

1.1 SECTION INCLUDES: Rigid roof insulation, vapor retarder, fasteners.

A. INSULATION: Material and manufacturer acceptable and responsible to RoofingMembrane manufacturer for compatibility with total roofing systems; rigid board units notover 48" x 48" size, used in a combination with a minimum of two (2) layer installationsystem with taper shown or as noted. Maximum thickness of any flat or taperedpolyisocyanurate roof insulation board to be 2.5" thick, maximum (unless otherwisespecified).

B. VAPOR BARRIER:

1. At roofs scheduled for a “re-cover” of existing modified roof: a. Existing modified roof to act as vapor barrier.

2. At roofs scheduled for a complete “tear -off” of existing roof: a. Install one layer of specified vapor barrier (see Section 07541) over the

top of the prepared roof deck, prior to installation of the new roofinsulation. Seal off all penetrations and perimeter with approved vaporbarrier tape to insure vapor and air seal. Tape all laps of vapor barrierwith approved tape.

C. TAPERED EDGE: 1½” x 18" tapered edge strip (at roof drains, scuppers, etc.), ½” x 6"tapered edge strip at start of taper system.

D. INSULATION PLATES - 3 inch square or round, stamping of SAE 1010 steel with an AZ 55Galvalume coating:

1. Base Bid:a. Sarnafil - Sarnaplate-HD/CDb. FiberTite - #330 FTR Insulation Plate

2. Alternate Bid:a. Versico – Insulation Fastening Platesb. Carlisle – Insulation Fastening Plates

E. INSULATION FASTENERS - A #14 (minimum) corrosion-resistant fastener with a buttressthread, used with insulation plates to attach insulation boards to steel or wood roof decks.

1. Base Bid:a. Sarnafil - Sarnafastener-HDb. FiberTite - FTR #14 Fastener

2. Alternate Bid:a. Versico – ASAP Insultite Insulation Fastenersb. Carlisle - HP-X Fasteners

F. FASTENING REQUIREMENTS - Fasten at a minimum rate of one fastener every two (2)

square feet or as required to meet Factory Mutual (FM) I-90 and Bulletin 1-28s windrequirements, whichever is more stringent. Comply with additional fasteningrequirements at perimeter and corners per FM Bulletin 1-28s.



10/629


LPSCM 07 22 10 - 1

07 22 10 – ROOF INSULATION

PART 1 – GENERAL

1.1 SECTION INCLUDES: Furnish and install new 2.0" thick polyisocyanurate roof insulation (where

scheduled), and new overlay insulation board of ⅝” gypsum overlayment board over top of newpolyisocyanurate roof insulation (where shown) and over existing prepared modified roof system, inaccordance with manufacturer's recommendations.

A General Requirements:

1. Flat and tapered insulation types and overly insulation board shall be supplied byroofing material manufacturer.

2. Insulation shall be approved by Factory Mutual and Underwriters Laboratories foruse as a roofing insulation.

3. Minimum LTTR aged R-Value of polyisocyanurate only: R-5.7 per inch.

4. Minimum aged R-Value of ½” Gypsum Overlayment Board: R-.56.

PART 2 – PRODUCTS

2 .1 FLAT POLYISOCYANURATE ROOF INSULATION BOARD: Provide at Sections _____________(as marked on drawings) and where existing polyisocyanurate roof insulation iswet/damaged/deteriorated and for fill board for tapered insulation areas.

A. Flat Polyisocyanurate with Coated Glass Facer :

1. ASTM C 1289-14, Type II, Class 2 Standard Specification for Polyurethane andPolyisocyanurate Roof Insulation.

2. Total Thickness (one layer of 2.0 inch). Flat polyisocyanurate insulation panelsare to be installed in multiple layers and are to be 48" x 48" in size.

3. Maximum Thickness (of any one layer): 2.5”. Any layer of flat or tapered

polyisocyanurate roof insulation is to be no thicker than 2.5” thick. 4. Manufacturers - Base Bid:

a. Sarnafil - Sarnatherm Insulation - in 4 ft x 4 ft and specified thickness.b. FiberTite - FTR Value Insulation - in 4 ft x 4 ft and specified thickness.

5. Manufacturers - Alternate Bid:a. Versico – SecurShield HD- in 4 ft x 4 ft and specified thickness.b. Carlisle - SecurShield HD - in 4 ft x 4 ft and specified thickness.

2 .2 TAPERED POLYISOCYANURATE ROOF INSULATION: Provide at areas (where shown ondrawings) and behind high side of all roof curbs.

1. Tapered Polyisocyanurate (with coated glass facer) Overlay Crickets:a. ASTM C 1289, Type II, Class 2 Standard Specification for Polyurethane

and Polyisocyanurate Roof Insulation.b. Minimum Thickness: ½". Tapered “cricket” material is to be fabricated

using sloped panels with a slope of ½” -per-foot material. Install 6" T.E.S.(tapered edge strip) at the starting point of all tapered panels.

2. Manufacturers - Base Bid:a. Sarnafil - Sarnatherm Insulation - in 4 ft x 4 ft and specified thickness.b. FiberTite - FTR Value Insulation - in 4 ft x 4 ft and specified thickness.

3. Manufacturers - Alternate Bid:


11/629


LPSCM 07 22 10 - 2

a. Versico – MP-H Tapered ISO - in 4 ft x 4 ft and specified thickness.b. Carlisle - SecurShield Polyisocyanurate - in 4 ft x 4 ft and specified

thickness.

2 .3 OVERLAYMENT BOARD (Supplied and warranted by the roof manufacturer):

1. Securerock® Gypsum-Fiber Roof Board - A fire tested, fiber-reinforced, water-

resistant hardboard. Securerock

®

is provided in a 4 ft x 4 ft in thickness of ⅝ inch.Install over all flat roof areas.

2. Dens-Deck® Prime - A fire-tested, gypsum hardboard with glass-mat facers and a

pre-primed surface on one side. Dens-Deck® Prime is provided in a 4 ft x 4 ft in

thickness of ⅝” inch. Install over all flat roof areas.

2 .4 INSULATION ADHESIVE:

A. Two-Part Foam Adhesive (provide twin cartridge packs, DO NOT USE PACE CART).

1. Sarnafil - Sarnacol 2163

2. FiberTite - TR 601

3. Versico – Millennium One Step

4. Carlisle - Millennium One Step


3 .1 PREPARATION & INSTALLATION:

A. Power-wash the entire existing granular surfaced modified bitumen roof membranesurface, and remove all debris from the roof surface/job site.

B. Remove (cut-out) all existing MOLE RUNS from the existing granular surfaced modifiedbitumen membrane surface, and fill-in low areas with new “self -adhered” modified roofmembrane.

C. Where wet insulation is shown or suspected, confirm areas of wet insulation and removeany damaged polyisocyanurate roof insulation found and replace with new to matchexisting thickness.

D. At Sections _____________ :

1. Power-wash the entire existing granular surfaced modified bitumen roofmembrane surface, and remove all debris from the roof surface/job site.

2. Install specified flat (and tapered) polyisocyanurate roof insulation board with all joints staggered over the top of the prepared modified bitumen roof surface.Stagger all layers of roof insulation in both directions by minimum of 24 inches(Stagger joints between all layers). This requirement includes tapered insulationand fill insulation. Joints shall be ⅛" or less in width. Fill all uneven or oversizedinsulation joints. Neatly cut and fit insulation around roof penetrations andprojections. Install only dry insulation and only as much insulation as can be

covered the same day with membrane and completed. (Insulation that hasbecome wet during storage will be marked with paint by the consultant, andremoved from site by the contractor.) Install insulation layers mechanicallyfastened to the substrate using manufacturer and Factory Mutual approvedfasteners, fastened at a minimum rate of one fastener every two (2) square feet oras required to meet Factory Mutual (FM) I-90 and Bulletin 1-28s windrequirements, whichever is more stringent.

E. Installation of overlayment board:


12/629


LPSCM 07 22 10 - 3

1. Install specified ⅝” gypsum overlayment board (all joints staggered), joints shall be⅛" or less in width. Fill all uneven or oversized insulation joints. Neatly cut and fitinsulation around roof penetrations and projections. Install only dry overlaymentboard and only as much board as can be covered the same day with membraneand completed. (Overlayment board that has become wet during storage will bemarked with paint by the consultant, and removed from site by the contractor.)

2. Install specified ⅝” gypsum overlayment board adhered to the newpolyisocyanurate at Sections _____________ (as marked on drawings) inmanufacturer-provided foam adhesive. Insure boards are properly adhered and“walked” in (using temporary weight ballast as necessary) to insure that no cornersare sticking up.

3. Install specified ⅝” gypsum overlayment board adhered to the existing modifiedmembrane surface by:a. Power-wash the existing modified bitumen membrane surface.b. Cut out and patch existing MOLE RUNS.c. Install overlayment board in manufacturer provided foam adhesive in

accordance with adhesive manufacturer’s pull test requirements (contact Adco/Royal adhesives for pull test results) for spacing and adhesion.Insure boards are properly adhered and “walked” in to insure that nocorners are sticking up.



13/629


LPSCM 07 54 10 - 1

07 54 10 – ADHERED THERMOPLASTIC MEMBRANE ROOFING

PART 1 - GENERAL

1.1 SECTION INCLUDES:

A. Scope - To install an adhered thermoplastic roofing membrane with flashings and othercomponents to comprise a roofing system.

B. Related Work - The work includes but is not necessarily limited to the installation of:

1. Removal of Existing Roofing and Insulation

2. Substrate Preparation

3. Roof Drains

4. Wood Blocking

5. Insulation

6. Roof Membrane

7. Fasteners

8. Adhesive for Flashings

9. Roof Membrane Flashings

10. Walkways

11. Metal Flashings

12. Sealants

C. Upon successful completion of work the following warranties will be obtained:

1. Manufacturer Warranty

2. Roofing Contractor Warranty

1.2 RELATED SECTIONS A. Alterations project procedures – LPS General Conditions of the Contract and Division 07.

B. Wood nailers, wood/metal cementitious roof deck renovation – Section 07 01 50.

C. Metal flashing and other sheet metal items – Section 07 62 00.

1.3 ALTERNATES

A. Alternates that may be contemplated/required for this project will comply with proceduresspecified in the LPS General Conditions of the Contract and Division 07.

1.4 QUALITY ASSURANCE

A. This roofing system shall be applied only by a Roofing Contractor authorized by the roofManufacturer prior to bid ("Applicator").

B. A single applicator with a minimum of 10 years previous successful experience ininstallation of similar systems.

C. Shall maintain a permanent office within 65 miles distance of project site to satisfy Ownerthat projects can be properly serviced during guaranty phase.

D. Upon completion of the installation and the delivery to the manufacturer by the Applicatorof a certification that all work has been done in strict accordance with the contractspecifications and the manufacturer's requirements, an inspection shall be made by aTechnical Representative of the manufacturer to review the installed roof system.


14/629


LPSCM 07 54 10 - 2

E. There shall be no deviation made from the Project Specification or the approved shopdrawings without prior written approval by the Owner, the Owner's Representative and themanufacturer.

F. All work pertaining to the installation of the manufacturer membrane and flashings shallonly be completed by Applicator personnel trained and authorized by the manufacturer inthose procedures.

G. Pre-Installation Conference:

1. Prior to installation of roofing system, conduct a Pre-Installation conference at theproject site.

2. Attendance: Owner, Roofing Consultant, Contractor, project superintendent,project foreperson, and Roof Manufacturer's Technical Representative. Allow14 days notice to manufacturer for scheduling of their representative.

3. Agenda: Refer to Division One requirements.

H. Daily Job Reports

1. Contractor is responsible for providing daily job reports which will include aminimum of the following information: Crew size, weather conditions, description of

work completed, date, change order items, job problems, etc. Contractor willemail daily job reports daily to the roof consultant.

1.5 SUBMITTALS

A. Shop Drawings:

1. Submit six (6) copies of drawing indicating roof size, location and type ofpenetrations, perimeter and penetration details. Indicate complete installationdetails of roofing and flashing, including roof slopes, flashing details, penetrationdetails and accessories. Technical acceptance from the manufacturer.

2. Sheet metal shop drawings: Submit six (6) copies of sheet metal shop drawingsshowing size, layout and location of all sheet metal items.

3. Submit two (2) copies of MSDS data directly to the owner for their files, on all

roofing, insulation, adhesive and other related materials.

4. Submit three (3) 12" x 12" samples of thermoplastic roof membrane to be used,taken from rolls on the roof. Provide “Lot Numbers” from roll goods taken fromrolls on the roof.

B. Product Data: Submit four (4) copies of latest edition of manufacturer's roofing andflashing specifications, including list of materials proposed for use, and manufacturer'sdata sheets for other products.

C. Progress Schedule Plan:

1. Submit a complete progress schedule and phasing plan indicating completesequence of removal and replacement of roofing for each area.

2. Include roof plan with layout indicating amount of roof area included in each day'swork.

3. Indicate dates for beginning and completing each activity.

4. Identify other related work affecting roof replacement and phasing.

D. Warranty: Submit specimen copy of contractor and manufacturer's roofing warranty (thatcomplies with guaranty requirements as listed in paragraph 1.10 below), with Product Datasubmittal, including evidence of application for warranty.


15/629


LPSCM 07 54 10 - 3

E. Manufacturer's Review: Concurrent with Shop Drawing submittal; submit (in writing) roofmanufacturer's review and acceptance of Contract Documents (plans, specifications,application requirements, etc.) and approval of applicator. Certifications by manufacturersof roofing and insulating materials that all materials supplied comply with all requirementsof the identified ASTM and industry standards or practices.

F. Certification from the Applicator that the system specified meets all identified code and

insurance requirements as required by the Specification.

G. Maintenance Data: Compile and submit maintenance instructions in accordance withDivision One. Include complete manufacturer's instructions for periodic inspection andmaintenance of roofing system, including precautions and warnings to prevent damageand deterioration to roofing system.

1.6 CODE REQUIREMENTS - The applicator shall submit evidence that the proposed roof systemmeets the requirements of the local building code and has been tested and approved or listed bythe following test organizations. These requirements are minimum standards and no roofing workshall commence without written documentation of the system's compliance, as required in the"Submittals" section of this specification.

A. Factory Mutual Research Corporation (FM) - Norwood, MA

1. Class I-90 (for high wind exposure)B. Underwriters Laboratories, Inc. - Northbrook, IL

1. Class A assembly

C. Littleton Building Department.

D. International Building Code (latest adopted edition).

1.7 PRODUCT DELIVERY, STORAGE AND HANDLING

A. All products delivered to the job site shall be in the original unopened containers orwrappings bearing all seals and approvals.

B. Handle all materials to prevent damage. A maximum of one (1) weeks worth of roofinsulation and roll goods may be stored on the roof, as long as materials are on raised

platforms (pallets), roof structure is not overloaded, and materials are covered withwatertight tarpaulins. Visqueen is not an acceptable watertight material for protectingroof materials.

C. Materials loaded on roof levels for immediate (within one week) use shall be:

1. Distributed to prevent concentrated loads that would impose excessive strain ondeck or structural members.

2. Positively secured to prevent displacement by excessive wind forces.

D. Membrane rolls shall be stored lying down on pallets and fully protected from the weatherwith clean canvas tarpaulins. Unvented polyethylene tarpaulins are not accepted due tothe accumulation of moisture beneath the tarpaulin in certain weather conditions that mayaffect the ease of membrane weldability.

E. Provide continuous protection of materials against wetting and absorption; site. Allmaterials which are determined to be damaged (i.e. wet materials and marked materialsthat have been wet) by the Owner's Representative or the manufacturer are to be removedfrom the job site and replaced at no cost to the Owner.

F. All adhesives shall be stored at temperatures between 40º F and 80º F.

G. All flammable materials shall be stored in a cool, dry area away from sparks and openflames. Follow precautions outlined on containers or supplied by materialmanufacturer/supplier.


16/629


LPSCM 07 54 10 - 4

1.8 JOB CONDITIONS

A. Existing Conditions: Examine existing building and existing roofing to determine existingphysical conditions that affect removal of existing roofing and installation of new roofing.

B. Only as much of the new roofing as can be made weathertight each day, including allflashing and detail work, shall be installed. Do not remove existing roofing and flashing in

inclement weather or when rain is predicted (30% or more possibility). All seams shall becleaned and heat welded before leaving the job site that day.

C. All work shall be scheduled and executed without exposing the interior building areas to theeffects of inclement weather. The existing building and its contents shall be protectedagainst all risks.

D. All surfaces to receive new insulation, membrane or flashings shall be dry. Should surfacemoisture occur, the Applicator shall provide the necessary equipment to dry the surfaceprior to application.

E. All new and temporary construction, including equipment and accessories, shall besecured in such a manner as to preclude wind blow-off and subsequent roof or equipmentdamage.

F. Uninterrupted waterstops shall be installed at the end of each day's work and shall becompletely removed before proceeding with the next day's work. Waterstops shall not emitdangerous or unsafe fumes and shall not remain in contact with the finished roof as theinstallation progresses. Contaminated membrane shall be replaced at no cost to theOwner.

G. The Applicator is cautioned that certain roof membranes are incompatible with asphalt,coal tar, heavy oils, roofing cements, creosote and some preservative materials. Suchmaterials shall not remain in contact with the manufacturer membranes. The Applicatorshall consult the manufacturer regarding compatibility, precautions and recommendations.

H. Arrange work sequence to avoid use of newly constructed roofing as a walking surface orfor equipment movement and storage. Where such access is absolutely required, the Applicator shall provide all necessary protection and barriers to segregate the work areaand to prevent damage to adjacent areas. A substantial protection layer consisting of

plywood over Sarnafelt or plywood over insulation board shall be provided for all new andexisting roof areas that receive rooftop traffic during construction.

I. Prior to and during application, all dirt, debris and dust shall be removed from surfaces byvacuuming, sweeping, blowing with compressed air and/or similar methods.

J. The Applicator shall follow all safety regulations as required by OSHA and any otherapplicable authority having jurisdiction.

K. All roofing, insulation, flashings and metal work removed during construction shall beimmediately taken off site to a legal dumping area authorized to receive such materials.Hazardous materials, such as materials containing asbestos, are to be removed anddisposed of in strict accordance with applicable City, State and Federal requirements.

L. All new roofing waste material (i.e., scrap roof membrane, empty cans of adhesive) shall

be immediately removed from the site by the Applicator and properly transported to a legaldumping area authorized to receive such material.

M. The Applicator shall take precautions that storage and/or application of materials and/orequipment does not overload the roof deck or building structure.

N. Flammable adhesives and deck primers shall not be stored and not be used in the vicinityof open flames, sparks and excessive heat.

O. All rooftop contamination that is anticipated or that is occurring shall be reported to themanufacturer to determine the corrective steps to be taken.


17/629


LPSCM 07 54 10 - 5

P. The Applicator shall verify that all roof drain lines are functioning correctly (not clogged orblocked) before starting work. Applicator shall report any such blockages in writing (lettercopy to the manufacturer) to the Owner's Representative for corrective action prior toinstallation of the roof system.

Q. Applicator shall immediately notify the owner’s representative if any unusual or concealedcondition is discovered that adversely affects the work, for determination of how to

proceed.

R. Site cleanup, including both interior and exterior building areas that have been affected byconstruction, shall be completed to the Owner's satisfaction.

S. All landscaped areas damaged by construction activities shall be repaired at no cost to theOwner.

T. The Applicator shall conduct fastener pullout and/or adhesive pull tests in accordancewith the latest revision of the SPRI/ANSI Fastener Pullout Standard to help verify conditionof deck/substrate prior to beginning the reroof work, and to confirm expected pulloutvalues.

U. Precautions shall be taken when using adhesives at or near rooftop vents or air intakes. Adhesive odors could enter the building. Coordinate the operation of vents and air intakes

in such a manner as to avoid the intake of adhesive odor while ventilating the building.Keep lids on unused cans at all times.

V. Protective wear shall be worn when using solvents or adhesives or as required by jobconditions.

W. Emergency Equipment: Maintain on-site equipment necessary to apply emergencytemporary edge seal in the event of sudden storms or inclement weather.

X. Restrictions: Comply with requirements of Division One on use of site.

1. Smoking is prohibited on roof areas or in existing buildings or on grounds.

2. Radios, boom boxes, etc. are not allowed on the job site.

Y. Continuation of Services: Comply with requirements of Division One.

1.9 BIDDING REQUIREMENTS

A. Pre-Bid Meeting: A pre-bid meeting shall be held with the Owner, Owner's Representative,Manufacturer’s Representative and any other involved trades to discuss all aspects of theproject. The Applicator's representative for the work shall be in attendance.

B. Site Visit: Bidders shall visit the site and carefully examine the areas in question as toconditions that may affect proper execution of the work. All dimensions and quantitiesshall be determined or verified by the contractor. No claims for extra costs will be allowedbecause of lack of full knowledge of the existing conditions unless agreed to in advancewith the Owner or Owner's Representative.

1.10 WARRANTIES

A. Applicator/Roofing Contractor 2 Year MRCA Warranty - The Applicator shall supply the

Owner with a separate materials and workmanship warranty. In the event any work relatedto roofing, flashing, or metal is found to be within the Applicator warranty term, defective orotherwise not in accordance with the Contract Documents, the Applicator shall repair thatdefect at no cost to the Owner. The Applicator's warranty obligation shall run directly to theOwner.

B. The Manufacturer “20 Year No Dollar Limit (NDL) Total System Warranty” - Uponsuccessful completion of the work, the Manufacturer’s 20 Year No Dollar Limit (NDL) TotalSystem Warranty shall be issued covering all materials and workmanship including thefollowing:


18/629


LPSCM 07 54 10 - 6

1. Include repairs required to maintain roof and flashing in a watertight condition.

2. Make repairs at no expense to Owner.

3. Guaranty coverage to include:a. All roof insulations, insulation fasteners, insulation adhesives, vapor

retarders (where applicable), membrane fasteners and adhesives.

b. Roof membrane components and adhesives. All accessory productsrequired for installation of membrane roofing system, including bondingadhesive, flashing membrane, stripping plies, clad metal, pipe boots,pourable sealant pockets, etc.

4. Guaranty shall not exclude coverage as a result of small areas of standing orponding water.

5. Guaranty shall include hail (up to 1½") coverage for 20 years.

6. Guaranty shall not exclude coverage as a result of winds less than 85 m.p.h.

7. Guaranty shall not be limited by a dollar amount.

C. Owner Responsibility - Owner shall notify both the manufacturer and the Applicator of anyleaks as they occur during the time period when both warranties are in effect.

PART 2 - PRODUCTS

2.1 GENERAL:

A. Base Bid: The components of the thermoplastic adhered roof system are to be products ofSarnafil or FiberTite as specified.

B. Alternate Bid: The components of the thermoplastic adhered roof system are to beproducts of Versico or Carlisle as specified.

C. (Note accessories listed are not separated by Base Bid or Alternate Bid, but are listed byrespective manufacturer).

2.2 MEMBRANE - BASE BID

A. Sarnafil® G410 fiberglass reinforced membrane with a lacquer coating.

1. Membrane shall conform to ASTM D4434-12 (or latest revision), "Standard forPolyvinyl Chloride Sheet Roofing". Classification: Type II.

2. Sarnafil G410-15, 72 mil (minimum) thermoplastic membrane with fiberglassreinforcement.

B. FiberTite®-XT Dupont Dacron polyester reinforced membrane.

1. Membrane shall conform to ASTM D6754-02 (or latest revision), "StandardSpecification Ketone Ethylene Ester Based Sheet Roofing". Classification: TypeIV, Grade I.

2. 8142 FiberTite-XT, 50 mil (minimum) ethylene interpolymer (EIP) alloy, reinforcedwith knitted polyester fabric.

C. Certified Polymer Thickness

1. The membrane manufacturer is to certify that the polymer thickness is of thepolymer thickness specified (see 2.2 A.2 and 2.2 B.2). Certification is to be signedby the membrane manufacturer’s quality control manager. ASTM +/- tolerance formembrane thickness is not acceptable.

D. Color of Membrane

1. Sarnafil® - EnergySmart (TAN).


19/629


LPSCM 07 54 10 - 7

2. FiberTite® - Thermal Tan

2.3 MEMBRANE - ALTERNATE BID

A. Versico VersiFlex E® – KEE HP 60 mil thermoplastic reinforced membrane.

1. Membrane shall conform to ASTM D4434-12 (or latest revision), "Standard forPolyvinyl Chloride Sheet Roofing". Classification: Type III.

B. Carlisle SureFlex® KEE HP 60 Mil thermoplastic reinforced membrane.

1. Membrane shall conform to ASTM D4434-12 (or latest revision), "Standard forPolyvinyl Chloride Sheet Roofing". Classification: Type III.

C. Certified Polymer Thickness

1. The membrane manufacturer is to certify that the polymer thickness is of thepolymer thickness specified (see 2.3 A and 2.B). Certification is to be signed bythe membrane manufacturer’s quality control manager. ASTM +/- tolerance formembrane thickness is not acceptable.

D. Color of Membrane

1. Versico® - Tan

2. Carlisle® - Tan

2.4 FLASHING MATERIALS

A. Wall /Curb Flashing

1. Sarnafil G410 Membrane or Sarnafil G459 Membrane

2. FiberTite XT Membrane

3. Versico VersiFlex E KEE HP Membrane

4. Carlisle SureFlex KEE HP Membrane

B. Perimeter Edge Flashing

1. Sarnaclad PVC-coated, heat-weldable sheet metal.

2. FiberClad Metal – Polymeric-coated, heat-weldable sheet metal.

3. Versico VersiFlex Coated Metal

4. Carlisle SureFlex PVC Coated Metal

C. Miscellaneous Flashing

1. Termination Bar - A heavy-duty, extruded aluminum flashing termination bar usedat walls and large curbs. ⅛” x 1" x 10 foot lengths. a. Sarnafil - Termination Bar with Caulk Lipb. FiberTite - 109 Termination Bar (Caulk Lip)c. Versico – Termination Bard. Carlisle – HP Termination Bar

2. Prefabricated vent pipe flashinga. Sarnafil - Sarnastackb. FiberTite - FTR Conesc. Versico – VersiFlex PVC Pipe Sealsd. Carlisle – SureFlex PVC Pipe Seals

3. PVC-coated, heavy-duty aluminum roof drain insert that mechanically seals to thedrainpipe interiora. Sarnafil - Sarnadrain-RACb. FiberTite - U-Flow Hercules


20/629


LPSCM 07 54 10 - 8

c. Versico – Insert Drain Systemd. Carlisle – Insert Drain System

4. T-Joint membrane patches welded over T-jointsa. Sarnafil - Sarnacircle "G"b. FiberTite - XT Membranec. Versico – VersiFlex T-Joint Covers

d. Carlisle – SureFlex T-Joint Covers

5. Urethane sealant used for pitch pocket toppinga. Sarnafil - Sarnafillerb. FiberTite - FTR SL Sealantc. Versico – White One-Part Pourable Sealerd. Carlisle - PVC One-Part Pourable Sealer

6. Prefabricated outside and inside flashing cornersa. Sarnafil - Sarnacornerb. FiberTite - FTR Cornersc. Versico – VersiFlex Inside and Outside Cornersd. Carlisle – SureFlex Inside and Outside Corners

7. Sealant used at flashing terminationsa. Sarnafil - Multi-Purpose Sealantb. FiberTite - FTR 101 Caulkingc. Versico – Universal Single-Ply Sealantd. Carlisle - Universal Single-Ply Sealant

8. Bonding Adhesive for Field Membranea. Sarnacol 2170 Adhesive - A solvent-based reactivating-type adhesive

used to attach the membrane to horizontal or near-horizontal substrates.b. FiberTite - FTR 190 Adhesive: A solvent-based contact adhesive (2 sided)

for vertical & horizontal surfaces.c. Versico – PVC Low-VOC Bonding Adhesive – A Low VOC solvent based

contact adhesive.d. Carlisle - PVC Low-VOC Bonding Adhesive – A Low VOC solvent based

contact adhesive.9. Bonding Adhesive for Flashing Membrane

a. Sarnacol 2170 Adhesive - A solvent-based reactivating-type adhesiveused to attach membrane to flashing substrate.

b. FiberTite - FTR 190 Adhesive: A solvent-based contact adhesive (2 sided)for vertical & horizontal surfaces.

c. Versico – PVC Low-VOC Bonding Adhesive – A Low VOC solvent basedcontact adhesive.

d. Carlisle - PVC Low-VOC Bonding Adhesive – A Low VOC solvent basedcontact adhesive.

10. A non-woven polyester or polypropylene mat cushion layer that is necessarybehind Flashing Membrane when the flashing substrates are rough-surfaced orincompatible with the flashing membrane.a. Sarnafil - Sarnafeltb. FiberTite - 8240 FiberTite FBc. Versico – HP Protective Matd. Carlisle - HP Protective Mat

2.5 INSULATION & OVERLAYMENT BOARDS (See Section 07220 & 07221)

A. Polyisocyanurate foam insulation with COATED GLASS facers

1. Sarnafil - Sarnatherm Insulation - in 4 ft x 4 ft and specified thickness.


21/629


LPSCM 07 54 10 - 9

2. FiberTite - FTR Value Insulation - in 4 ft x 4 ft and specified thickness.

3. Versico – MP-H - in 4 ft x 4 ft and specified thickness.

4. Carlisle - HP-H Polyisocyanurate – in 4 ft. x 4 ft. and specified thickness

B. Overlayment board

1. Securerock

®

Gypsum-Fiber Roof Board - A fire tested, fiber-reinforced, water-resistant hardboard. Securerock® is provided in a 4 ft x 4 ft in thickness of ⅝ inch.

Install over all flat roof areas.

2. Dens-Deck® Prime - A fire-tested, gypsum hardboard with glass-mat facers and a

pre-primed surface on one side. Dens-Deck® Prime is provided in a 4 ft x 4 ft in

thickness of ⅝ inch. Install over all flat roof areas.

2.6 ATTACHMENT COMPONENTS

A. Membrane Adhesive

1. Sarnafil - Sarnacol 2170 Adhesive: A solvent-based reactivating-type adhesiveused to attach the roofing membrane to the roof substrate.a. Do not install when air temperature is within 5º F of dew point. Solvent

evaporation time increases significantly when temperatures drop. Ensurefirst layer of Sarnacol 2170 is fully dry before second layer is applied to theback of the membrane for proper reactivation.

b. Use a water-filled, foam-covered lawn roller to consistently and evenlypress the membrane into the adhesive layer.

2. FiberTite - FTR 190 Adhesive: A solvent-based contact adhesive (2 sided) forhorizontal surfaces.a. Do not install when air temperature is within 5º F of dew point. Solvent

evaporation time increases significantly when temperatures drop.b. Use a water-filled, foam-covered lawn roller to consistently and evenly

press the membrane into the adhesive layer.

3. Versico - PVC Low-VOC Bonding Adhesive – A Low VOC solvent based contactadhesive.

a. Do not install when air temperature is within 5º F of dew point. Solventevaporation time increases significantly when temperatures drop.

b. Use a split weighted roller to roll the coated membrane into adhesive andimmediately brush with a soft bristle push broom.

4. Carlisle - PVC Low-VOC Bonding Adhesive – A Low VOC solvent based contactadhesive.a. Do not install when air temperature is within 5º F of dew point. Solvent

evaporation time increases significantly when temperatures drop.b. Use a split weighted roller to roll the coated membrane into adhesive and

immediately brush with a soft bristle push broom.

B. Flashing Adhesive

1. Sarnafil - Sarnacol 2170 Adhesive: A solvent-based reactivating-type adhesiveused to attach the flashing membrane to the substrate vertically.a. Do not install when air temperature is within 5º F of dew point. Solvent

evaporation time increases significantly when temperatures drop. Ensurefirst layer of Sarnacol 2170 is fully dry before second layer is applied to theback of the membrane for proper reactivation.

2. FiberTite - FTR 190 Adhesive: A solvent-based contact adhesive (2 sided) forvertical surfaces.a. Do not install when air temperature is within 5º F of dew point. Solvent

evaporation time increases significantly when temperatures drop.


22/629


LPSCM 07 54 10 - 10

3. Versico - PVC Low-VOC Bonding Adhesive – A Low VOC solvent based contactadhesive.a. Do not install when air temperature is within 5º F of dew point. Solvent

evaporation time increases significantly when temperatures drop.

4. Carlisle - PVC Low-VOC Bonding Adhesive – A Low VOC solvent based contactadhesive.

a. Do not install when air temperature is within 5º F of dew point. Solventevaporation time increases significantly when temperatures drop.

C. Insulation Plates - 3 inch square or round, stamping of SAE 1010 steel with an AZ 55Galvalume coating:

1. Sarnafil - Sarnaplate-HD/CD

2. FiberTite - #330 FTR Insulation Plate

3. Versico – Insulation Fastening Plates

4. Carlisle – Insulation Fastening Plates

D. Insulation Fasteners - A #14 (minimum) corrosion-resistant fastener with a buttress thread,used with insulation plates to attach insulation boards to steel or wood roof decks.

1. Sarnafil - Sarnafastener-HD

2. FiberTite - FTR #14 Fastener

3. Versico - ASAP Insultite Insulation Fasteners

4. Carlisle - HP- Fasteners

E. Termination Bar - An extruded aluminum, low profile bar used with approved fasteners 1inch wide, flat aluminum bar 1/8 inch thick that has predrilled holes every 6 inches oncenter.

1. Sarnafil - Sarnastop

2. FiberTite - FTR Termination Bar

3. Versico – Termination Bar4. Carlisle – Termination Bar

F. Peel/batten Bar - An FM-approved, heavy-duty, 14 gauge(minimum), galvanized orstainless, roll-formed steel bar used to attach membrane to roof decks.

1. Sarnafil - Sarnabar

2. FiberTite - FTR Termination Bar

3. Versico – Metal Fastening Bar

4. Carlisle – Metal Fastening Bar

2.7 WALKWAY PROTECTION - A layer of specified walkway installed around all curbs and at all roofaccess locations, adhered to the prepared roof surface per manufacturers requirements and

specifications.

A. Sarnafil - Sarnatred - A polyester reinforced weldable membrane with surfaceembossment. Used as a protection layer from rooftop traffic.

B. FiberTite - Tuff-Trac “KEE” - A high grade vinyl walkway/protection material with ribbed“slip resistant” design. Used as a protection layer from rooftop traffic.

C. Versico – PVC Heat Weldable Walkway Roll – Slip resistant weldable walkways pad with aweathering package. Used in areas exposed to repetitive foot traffic.


23/629


LPSCM 07 54 10 - 11

D. Carlisle - Sure-Flex PVC Walkway Rolls – A textured surface to resist slipping formulatedwith a weathering packaged. Use in areas exposed to heavy foot traffic.

2.8 MISCELLANEOUS ACCESSORIES

A. Aluminum Tape - A 2 inch wide pressure-sensitive aluminum tape used as a separationlayer between small areas of asphalt contamination and the membrane and as a bond-

breaker under the coverstrip at clad-metal joints.B. Sealing Tape Strip - Compressible foam with pressure-sensitive adhesive on one side.

Used with metal flashings as a preventive measure against air and wind blown moistureentry.

C. Multi-Purpose Tape - A high performance sealant tape with used with metal flashings as apreventive measure against air and wind blown moisture entry.

D. Solvent Cleaner - A high quality solvent cleaner used for the general cleaning of residualasphalt, scuff marks, etc., from the membrane surface. Solvent cleaner is also used dailyto clean seam areas prior to hot-air welding in tear off or dirty conditions or if themembrane is not welded the same day it is unrolled.

1. Sarnafil - Sarnasolv

2. FiberTite - Acetone3. Versico – PVC Membrane Cleaner

4. Carlisle – PVC Membrane Cleaner

2.9 VAPOR RETARDER

A. At roofs scheduled for a “recover” of existing modified roof:

1. Existing modified roof to act as vapor barrier.

B. At roofs scheduled for a complete “tear -off” of existing roof:

1. Sarnavap-10 - A 10 mil thick polyethylene vapor retarder/air retarder. Sarnavap-10is supplied in a folded panel that is rolled onto a core. The core width is 5 feet.When unrolled off the core and unfolded, the sheet dimensions are 20 feet wide

by 100 feet long.

2. FiberTite -Griffolyn Type 65: Install one-ply of Griffolyn reinforced polyethylene (10mil) vapor barrier over metal deck areas. Seal all laps, perimeters andpenetrations with manufacturer supplied polyethylene tape, per manufacturer’srequirements.

3. Versico – 725TR Air & Vapor Barrier – A 40 mil composite consisting of 35 mils ofself-adhering rubberized asphalt laminated to a 5-mil woven polypropylene film ina 244 square foot roll.

4. Carlisle - 725TR Air & Vapor Barrier – A 40 mil composite consisting of 35 mils ofself-adhering rubberized asphalt laminated to a 5-mil woven polypropylene film ina 244 square foot roll.

2.10 SEALANTS AND PITCH POCKET FILLERS

A. Caulking/Sealant - (for termination details).

1. Sarnafil - Multi-Purpose Sealant

2. FiberTite - FTR #101 Caulking

3. Versico – Universal Single-Ply Sealant

4. Carlisle – Universal Single-Ply Sealant

B. Pourable Sealant


24/629


LPSCM 07 54 10 - 12

1. Sarnafil - Sarnafiller (two-part urethane filler for pitch pocket toppings).

2. FiberTite - FTR SL Sealant (one component pourable sealant for pitch pockettoppings).

3. Versico – PVC One-Part Pourable Sealer

4. Carlisle – PVC One-Part Pourable Sealer

C. Depending on substrates, the following sealants are options for temporary overnight tie-ins:

1. Type III hot asphalt conforming to ASTM D312 (latest revision).

2. Pourable Sealants.

3. Multiple layers of roofing cement and felt.

4. Spray-applied, water-resistant urethane foam.

5. Mechanical attachment with rigid bars and compressed sealant.

2.11 MISCELLANEOUS FASTENERS AND ANCHOR

A. All fasteners, anchors, nails, straps, bars, etc. shall be post-galvanized steel, aluminum orstainless steel. Mixing metal types and methods of contact shall be assembled in such a

manner as to avoid galvanic corrosion. Fasteners for attachment of metal to masonryshall be expansion type fasteners with stainless steel pins. All concrete fasteners andanchors shall have a minimum embedment of 1¼ inch and shall be approved for such useby the fastener manufacturer. All miscellaneous wood fasteners and anchors used forflashings shall have a minimum embedment of 1 inch and shall be approved for such useby the fastener manufacturer.

2.12 RELATED MATERIALS

A. Wood Nailer - Treated wood nailers shall be installed at the perimeter of the entire roofand around such other roof projections and penetrations as specified on Project Drawings.Thickness of nailers must match the insulation thickness to achieve a smooth transition.Wood nailers shall be treated for rot resistance (wolmanized or osmose treated) and be #2quality or better lumber. Creosote or asphalt-treated wood is not acceptable. Wood

nailers shall conform to Factory Mutual Loss Prevention Data Sheet 1-49. All wood shallhave a maximum moisture content of 19% by weight on a dry-weight basis.

B. Plywood - When bonding directly to plywood, a minimum ½ inch CDX © side out), smooth-surfaced exterior grade plywood with exterior grade glue shall be used. Rough-surfacedplywood or high fastener heads will require the use of felt behind the flashing membrane.Plywood shall have a maximum moisture content of 19% by weight on a dry weight basis.

C. Gas Pipe/Electrical Conduit Supports: Furnish and install Miro Industries gas pipe supportsModel Numbers 4-RAH or 6-RAH (hot dipped galvanized) (size as required for gas pipe onroof) per manufacturer requirements and spaced a minimum of 10' o.c and at all corners.Install over an extra layer of specified walkway pad.

D. Electrical Conduit Supports: Furnish and install Miro Industries Pillow Block Pipe StandsModel 1.5 with 1.5 Spacer (for electrical conduits 3" or less above finished roof height).

PART 3 - EXECUTION

3.1 PRE-CONSTRUCTION CONFERENCE

A. The Applicator, Owner's Representative/Designer and Manufacturers shall attend apreconstruction conference.

B. The meeting shall discuss all aspects of the project including but not limited to:

1. Set up

2. Construction schedule


25/629


LPSCM 07 54 10 - 13

3. Contract conditions

4. Coordination of the work

3.2 SUBSTRATE CONDITION

A. Applicator shall be responsible for acceptance or provision of proper substrate to receivenew roofing materials.

B. Applicator shall verify that the work done under related sections meets the followingconditions:

1. Roof drains and/or scuppers have been reconditioned and/or replaced andinstalled properly.

2. Roof curbs, nailers, equipment supports, vents and other roof penetrations areproperly secured and prepared to receive new roofing materials.

3. All surfaces are smooth and free of dirt, debris and incompatible materials.

4. All roof surfaces shall be free of water, ice and snow.

3.3 SUBSTRATE PREPARATION - The roof deck and existing roof construction must be structurallysound to provide support for the new roof system. The Applicator shall load materials on the

rooftop in such a manner to eliminate risk of deck overload due to concentrated weight.

A. Reroofing with Removal of Existing Roofing

1. All existing roofing, base flashing, deteriorated wood blocking or deteriorated metalflashings shall be removed down to the existing substrate. Remove only thatamount of roofing and flashing which can be made weathertight with newmaterials during a one-day period and before the onset of inclement weather.

2. Exercise care in removal so as not to damage existing roof deck or adjacentsurfaces.

3. Do not stockpile debris on roof surface. Promptly remove debris each day. Usechutes to transfer debris from roof surface.

4. Do not haul debris over newly installed roof membranes.

5. Provide a clean tarp over the previous days roofing, prior to tear-off start, toprotect new roofing from dust, dirt, debris, etc., and from current days tear-off.

6. Steel Deck:a. FM Approved Steel Deck - Completely clean metal deck ribs of all roof

debris, trash, etc. prior to installation of new roof insulation. All rusted ordeteriorated decking shall be brought to the attention of the Owner'sRepresentative and to determine method of treatment or replacement.Surface-only rusted metal shall be sanded and treated with rust-inhibitingpaint. Sections that have rusted deeper than the surface or are notstructurally sound shall be removed and replaced. Deck type shall matchexisting and shall conform to FM's recommendations as outlined in FMLoss Prevention data Sheet I-28 and local requirements.

7. Wood Deck:a. Fastener heads shall be recessed into the wood surface.b. Non-FM Approved Wood Deck - All rotted or deteriorated wood shall be

removed and replaced. The deck thickness shall be 1½ inch (minimum)lumber or ½ (minimum) plywood or match existing deck if greater. Decktype and attachment shall conform to FM and local code requirements.Fastener heads shall be recessed into the wood surface.

8. Poured Structural Concrete Deck: The roof deck shall be smooth, even, free ofdust, dirt, excess moisture or oil and be structurally sound. Sharp ridges, other


26/629


LPSCM 07 54 10 - 14

projections and accumulations of bitumen above the surface shall be removed toensure a smooth surface before roofing. Any deteriorated decking shall berepaired.

9. Poured Lightweight Concrete Substrate: The roof deck shall be smooth, even, freeof dust, dirt, excess moisture or oil and be structurally sound. Sharp ridges, otherprojections and accumulations of bitumen above the surface shall be removed to

ensure a smooth surface before roofing. Any deteriorated decking shall berepaired.

10. Precast/Prestressed Concrete Deck: The roof deck shall be smooth, even, free ofdust, dirt, excess moisture or oil and be structurally sound. All joints betweenprecast units shall be grouted. Any differentials in height between precast unitsshall be feathered for a smooth transition. Any deteriorated decking shall berepaired.

11. Insulating Fill Substrate: All wet or deteriorated insulating fill shall be removed andreplaced. All accumulations of bitumen shall be removed and the surface of thedeck shall be smooth, and free of ridges and depressions. See steel/concreterequirements.

3.4 SUBSTRATE INSPECTION

A. A dry, clean and smooth substrate shall be prepared to receive the thermoplastic Adheredroof system.

B. The Applicator shall inspect the substrate for defects such as excessive surfaceroughness, contamination, structural inadequacy, or any other condition that will adverselyaffect the quality of work.

C. The substrate shall be clean, smooth, dry, free of flaws, sharp edges, loose and foreignmaterial, oil and grease. Roofing shall not start until all defects have been corrected.

D. All roof surfaces shall be free of water, ice and snow.

E. The roof membrane shall be applied over compatible and accepted substrates only.

3.5 WOOD NAILER INSTALLATION

A. Install continuous wood nailers at the perimeter of the entire roof and around roofprojections and penetrations as shown on the Detail Drawings.

B. Nailers shall be anchored to resist a minimum force of 300 pounds per lineal foot in anydirection. Individual nailer lengths shall not be less than 3 feet long. Nailer fastenerspacing shall be at 12 inches on center or 16 inches on center if necessary to match thestructural framing. Fasteners shall be staggered 1/3 the nailer width and installed within 6inches of each end. Two fasteners shall be installed at ends of nailer lengths. Nailerattachment shall meet this requirement and that of the current Factory Mutual LossPrevention Data Sheet 1-49.

C. Thickness shall be as required to match substrate or insulation height to allow a smoothtransition.

D. Any existing nailer woodwork which is to remain shall be firmly anchored in place to resist aminimum force of 300 pounds per lineal foot in any direction and shall be free of rot,excess moisture or deterioration. Only woodwork shown to be reused in Detail Drawingsshall be left in place. All other nailer woodwork shall be removed.

3.6 INSULATION INSTALLATION - (See Sections 07 22 00 & 07 22 10)

3.7 INSTALLATION OF THERMOPLASTIC MEMBRANE - The surface of the insulation or substrateshall be inspected prior to installation of the thermoplastic roof membrane. The substrate shall beclean, dry, free from debris and smooth with no surface roughness or contamination. Broken,delaminated, wet or damaged insulation boards shall be removed and replaced.


27/629


LPSCM 07 54 10 - 15

A. Membrane Adhesive:

1. Sarnacol 2170 - Adhesive shall be applied by roller. Roller applied adhesive shallutilize a solvent resistant ¾” nap roller, spreading the adhesive to insure a smooth,even 100% coverage of the substrate and membrane. Ensure first layer ofSarnacol 2170 is fully dry before second layer is applied to the back of themembrane for proper reactivation. The membrane shall be pressed firmly into the

adhesive layer with a water-filled, foam-covered lawn roller by frequent rolling intwo directions.

Notes:a. Do not install when air temperature is within 5º F of dew point. Solvent

evaporation time increases significantly when temperatures drop.b. No adhesive shall be applied in seam areas. All membrane shall be

applied in the same manner.

2. FTR 190 Adhesive - Apply a 100% continuos coat of bonding adhesive to theexposed bottom side of the membrane and a mirrored area of the substrate.a. Adhesive may be applied by roller or spraying. Roller applied adhesive

shall utilize a solvent resistant ¾” nap roller, spreading the adhesive toinsure a smooth, even 100% coverage of the substrate and membrane.

Spray applied adhesive must be spread out by roller to insure a smooth,even 100% of the substrate and membrane with no holidays, globs,puddles or similar irregularities.

b. Allow the adhesive to dry to a point of being tacky, but not stringy to thetouch. Do not allow adhesive to “dry out” completely.

c. When sufficiently dry, carefully maneuver the glued portion of themembrane onto the glued substrate surface, avoiding any wrinkles or airpockets.

d. The membrane shall be pressed firmly into the adhesive layer with awater-filled, foam-covered lawn roller by frequent rolling in two directions.

e. No adhesive shall be applied to the lap “seam” areas of the membrane.

3. Versico - VersiFlex PVC Low-Voc Bonding Adhesive - Application shall becontinuous and uniform, avoiding globs or puddles.

a. After thorough stirring (min 5 minutes), apply PVC Low-VOC Bonding Adhesive to substrate and membrane using a 9" (229 mm) medium naproller. PVC Low-VOC Bonding Adhesive must be allowed to dry until itdoes not string or stick to a dry finger touch. The membrane and substratewill be dry (non-tacky) to the finger touch. Any coated area which hasbeen exposed to rain should be allowed to dry and then recoated. Do notapply adhesive to splice areas to be hot-air welded.

b. Roll the membrane onto the adhesive-coated substrate while avoidingwrinkles. Immediately brush down the bonded portion of the sheet with asoft-bristle push broom or a clean dry roller applicator to achievemaximum contact.

4. Carlisle SureFlex - PVC Low-Voc Bonding Adhesive - Application shall becontinuous and uniform, avoiding globs or puddles.a. After thorough stirring (min 5 minutes), apply PVC Low-VOC Bonding

Adhesive to substrate and membrane using a 9" (229 mm) medium naproller. PVC Low-VOC Bonding Adhesive must be allowed to dry until itdoes not string or stick to a dry finger touch. The membrane and substratewill be dry (non-tacky) to the finger touch. Any coated area which hasbeen exposed to rain should be allowed to dry and then recoated. Do notapply adhesive to splice areas to be hot-air welded.

b. Roll the membrane onto the adhesive-coated substrate while avoidingwrinkles. Immediately brush down the bonded portion of the sheet with a


28/629


LPSCM 07 54 10 - 16

soft-bristle push broom or a clean dry roller applicator to achievemaximum contact.

3.8 HOT-AIR WELDING OF SEAM OVERLAPS

A. General

1. All seams shall be hot-air welded. All field seams exceeding 10 feet in length shall

be welded with an approved automatic welder. Seam overlaps should be 3 incheswide when automatic machine-welding and 4 inches wide when hand-welding,except for certain details.

2. Welding equipment shall be provided by or approved by the manufacturer. Allmechanics intending to use the equipment shall have successfully completed atraining course provided by the manufacturer Technical Representative prior towelding.

3. All membrane to be welded shall be clean and dry.

B. Hand-Welding - Hand-welded seams shall be completed in two stages. Hot-air weldingequipment shall be allowed to warm up for at least one minute prior to welding.

1. The back edge of the seam shall be welded with a narrow but continuous weld to

prevent loss of hot air during the final welding.2. The nozzle shall be inserted into the seam at a 45 degree angle to the edge of the

membrane. Once the proper welding temperature has been reached and themembrane begins to "flow," the hand roller is positioned perpendicular to thenozzle and pressed lightly. For straight seams, the 1½ inch wide nozzle isrecommended for use. For corners and compound connections, the ¾ inch widenozzle shall be used.

C. Machine Welding

1. Machine welded seams are achieved by the use of the manufacturer's automaticwelding equipment. When using this equipment, the manufacturer's instructionsshall be followed and local codes for electric supply, grounding and over currentprotection observed. Dedicated circuit house power or a dedicated portable

generator is recommended. No other equipment shall be operated off thegenerator.

2. Metal tracks may be used over the deck membrane and under the machinewelder to minimize or eliminate wrinkles.

D. Quality Control of Welded Seams

1. The Applicator shall check all welded seams for continuity using a roundedscrewdriver. Visible evidence that welding is proceeding correctly is smoke duringthe welding operation, shiny membrane surfaces, and an uninterrupted flow ofdark grey material from the underside of the top membrane. On-site evaluation ofwelded seams shall be made daily by the Applicator to locations as directed by theOwner's Representative or the manufacturer's representative. One inch widecross-section samples of welded seams shall be taken at least three times a day.Correct welds display failure from shearing of the membrane prior to separation ofthe weld. Each test cut shall be patched by the Applicator at no extra cost to theOwner.

3.9 MEMBRANE FLASHINGS - All flashings shall be installed concurrently with the roof membrane asthe job progresses. No temporary flashings shall be allowed without the prior written approval ofthe Owner's Representative and the manufacturer. Approval shall only be for specific locations onspecific dates. If any water is allowed to enter under the newly completed roofing, the affectedarea shall be removed and replaced at the Applicator's expense. Flashing shall be adhered to


29/629


LPSCM 07 54 10 - 17

compatible, dry, smooth, and solvent-resistant surfaces. Use caution to ensure adhesive fumesare not drawn into the building.

A. Adhesive for Membrane Flashings

1. Over the properly installed and prepared flashing substrate, approved bondingadhesive shall be applied according to instructions found on the Product Data

Sheet. The bonding adhesive shall be applied in smooth, even coats with no gaps,globs or similar inconsistencies. Only an area which can be completely covered inthe same day's operations shall be flashed. The bonded sheet shall be pressedfirmly in place with a hand roller.

2. No adhesive shall be applied in seam areas that are to be welded. All panels ofmembrane shall be applied in the same manner, overlapping the edges of thepanels as required by welding techniques.

B. Install termination bars and batten/peel bars according to the Detail Drawings withapproved fasteners into the structural deck at the base of parapets, walls and curbs.

C. The manufacturer's requirements and recommendations and the specifications shall befollowed. All material submittals shall have been accepted by the manufacturer prior toinstallation.

D. All flashings shall extend a minimum of 8 inches above roofing level unless otherwiseaccepted in writing by the Owner's Representative and the manufacturer’s TechnicalDepartment.

E. All flashing membranes shall be consistently adhered to substrates. All interior andexterior corners and miters shall be cut and hot-air welded into place. No bitumen shall bein contact with the thermoplastic membrane.

F. All flashing membranes shall be mechanically fastened along the counter-flashed topedge with Sarnastop at 6-8 inches on center.

G. Roof flashings shall be terminated according to the manufacturer’s recommended details.

H. All flashings that exceed 30 inches in height shall receive additional securement. Consultthe manufacturer’s Technical Department for securement methods.

3.10 METAL FLASHINGS

A. Metal details, fabrication practices and installation methods shall conform to the applicablerequirements of the following:

1. Factory Mutual Loss Prevention Data Sheet 1-49 (latest issue).

2. Sheet Metal and Air Conditioning Contractors National Association, Inc. (SMACNA)- latest issue.

B. Metal, other than that provided by the manufacturer, is not covered under the manufacturerwarranty.

C. Complete all metal work in conjunction with roofing and flashings so that a watertightcondition exists daily.

D. Metal shall be installed to provide adequate resistance to bending to allow for normalthermal expansion and contraction.

E. Metal joints shall be watertight.

F. Metal flashings shall be securely fastened into solid wood blocking. Fasteners shal lpenetrate the wood nailer a minimum of 1 inch.

G. Airtight and continuous metal hook strips are required behind metal fascias. Hook stripsare to be fastened 6 inches on center into the wood nailer or masonry wall.


30/629


LPSCM 07 54 10 - 18

H. Counter flashings shall overlap base flashings at least 4 inches.

I. Hook strips shall extend past wood nailers over wall surfaces by 1½ inch minimum andshall be securely sealed from air entry.

3.11 CLAD METAL EDGE METAL - All flashings shall be installed concurrently with the roof membraneas the job progresses. No temporary flashings shall be allowed without the prior written approval of

the Owner's Representative and the manufacturer. Acceptance shall only be for specific locationson specific dates. If any water is allowed to enter under the newly completed roofing due toincomplete flashings, the affected area shall be removed and replaced at the Applicator's expense.

A. Clad metal flashings shall be formed and installed per the Detail Drawings.

1. All metal flashings shall be fastened into solid wood nailers with two rows of postgalvanized flat head annular ring nails, 4 inches on center staggered. Fastenersshall penetrate the nailer a minimum of 1½ inch.

2. Metal shall be installed to provide adequate resistance to bending and allow fornormal thermal expansion and contraction.

B. Adjacent sheets of clad metal shall be spaced ¼ inch apart. The joint shall be coveredwith 2 inch wide aluminum tape. A 4 inch minimum wide strip of roof flashing membraneshall be hot-air welded over the joint.

3.12 WALKWAY INSTALLATION

A. Specified Walkway - Roofing membrane to receive walkway shall be clean and dry. Placechalk lines on deck sheet to indicate location of Walkway. Apply a continuous coat ofbonding adhesive to the deck sheet and the back of Walkway in accordance with themanufacturer's technical requirements and press Walkway into place with a water-filled,foam-covered lawn roller. Clean the deck membrane in areas to be welded. Hot-air weldthe entire perimeter of the Walkway to the thermoplastic deck sheet. Check all welds witha rounded screwdriver. Re-weld any inconsistencies. Important: Check all existing deckmembrane seams that are to be covered by Walkway with rounded screwdriver and reweldany inconsistencies before Walkway installation. Do not run Walkway overtermination/batten/peel bars.

3.13 TEMPORARY CUT-OFF A. All flashings shall be installed concurrently with the roof membrane in order to maintain a

watertight condition as the work progresses. All temporary waterstops shall be constructedto provide a 100% watertight seal. The stagger of the insulation joints shall be made evenby installing partial panels of insulation. The new membrane shall be carried into thewaterstop. The waterstop shall be sealed to the deck and/or substrate so that water will notbe allowed to travel under the new or existing roofing. The edge of the membrane shall besealed in a continuous heavy application of sealant as described in this section. Whenwork resumes, the contaminated membrane shall be cut out. All sealant, contaminatedmembrane, insulation fillers, etc. shall be removed from the work area and properlydisposed of off site. None of these materials shall be used in the new work.

B. If inclement weather occurs while a temporary waterstop is in place, the Applicator shallprovide the labor necessary to monitor the situation to maintain a watertight condition.

C. If any water is allowed to enter under the newly-completed roofing, the affected area shallbe removed and replaced at the Applicator's expense.

3.14 FIELD QUALITY CONTROL:

A. Roofing Contractor’s Quality Control:

1. During construction, contractor is to provide daily supervision of the project,performed by the contractor’s field superintendent (not to be confused with theproject foreperson who is on site at all times).


31/629


LPSCM 07 54 10 - 19

2. Contractor’s project manager is to perform regular site inspections at the minimumrate of one site visit per week.

3. Upon completion of installation, contractor is to perform their own final inspectionby their quality control person to confirm that roofing system has been installed inaccordance with the construction documents and manufacturer's requirements.Contractor is to produce a written punchlist and roof diagram of deficiencies found

during their final inspection. A copy of this punchlist, diagram and signedcompletion letter, will be provided to the consultant prior to the owner andconsultant performing their final inspection.

B. Manufacturer's Field Service:

1. During installation, provide for a minimum of two (2) on-site inspections of roofapplication by qualified technical representatives of roofing manufacturer.

2. Upon completion of installation, provide a final inspection by a technicalrepresentative of roofing manufacturer to confirm that roofing system has beeninstalled in accordance with manufacturer's requirements. The roofing contractor,owner and roof consultant are required to be present for this inspection. Themanufacturer is to produce a written punchlist and roof diagram of deficienciesfound during their final inspection. A copy of this punchlist, diagram and signedcompletion letter, will be provided to the owner’s roof consultant prior to the ownerand consultant performing their final inspection.

3. The manufacturer is to perform an 18-month inspection of the entire guaranteedroof system 18 months after the guaranty issuance date. The roofing contractor,owner and roof consultant are required to be present for this inspection.

3.15 CLEANING AND PATCHING:

A. Clean up debris, excess materials and equipment and remove from site.

B. Remove drippage or spills of coatings, sealant, adhesives or primers from finish surfaces.

C. Patch misaligned or inadequately lapped seams, inadequately adhered areas, puncturesor other damage to membrane with a patch of membrane sheet that extends at least 6 in.

in each direction from deficiency.3.16 PROTECTION:

A. Provide special protection (i.e. use of tarps and plywood), and avoid heavy traffic oncompleted work.

B. Restore to original condition or replace work or materials damaged during handling ofroofing materials.

3.17 COMPLETION

A. Prior to demobilization from the site, the work shall be reviewed by the Owner'sRepresentative and the Applicator. All defects noted and non-compliance with theSpecifications or the recommendations of the manufacturer shall be itemized in a punchlist. These items must be corrected immediately by the Applicator to the satisfaction of the

Owner's Representative and The manufacturer prior to demobilization.

B. All punch-lists shall have been completed, and warranties referenced in this Specificationshall have been delivered to the Owner’s Representative prior to the Owner accepting theproject for final payment.



32/629


LPSCM 07 61 00 - 1

07 61 00 – METAL ROOFING

PART 1 – GENERAL REQUIREMENTS

1.01 Description of Work

Work Included:

The extent of each type of performed metal panels are indicated on the drawings and byprovisions of this section. The scope of work includes, but shall not be limited to: preformedpanels, related accessories, valleys, hips, ridges, eaves, corners, rakes, miscellaneousflashings, and attaching devices.

1.02 Quality Assurance

Qualifications of Installers:

Competent and skilled sheet metal applicators familiar with products, standard details, andrecommendations. Applicator shall have at least two (2) years experience applying these typesof materials with successful completion of projects of similar scope.

1.03 Submittals

A. Submit the selected manufacturer's current specifications and installationrecommendations.

B. Provide samples.

C. Submit shop drawings showing roof plan profiles, details of forming, joining, trimflashing,and accessories. Show details of weatherproofing at edges, terminations andpenetrations of metal roofing work.

D. Warranties

1. A twenty-year paint finish guarantee is required from the manufacturer.2. A two-year weather-tightness guarantee is required from panel applicator.

PART 2 – PRODUCTS

2.01 Materials

A. Profile—to match existing.

B. Gauge and grade of substrate material—22-gauge steel.

C. Finish—baked on color to match existing.

D. Flashings, closures, trim, etc.—fabricate of same material, gauge and finish asadjacent panels.

E. Fasteners shall be as per manufacturer's recommendations.

PART 3 – DELIVERY, STORAGE, AND HANDLING

3.01 Delivery

A. Delivery of material shall be made only after suitable facilities for its storage andprotection are available on the site.

B. Upon receipt of preformed metal panels, flat sheets, flashings, and panel accessories,installer shall examine each shipment for damage and completeness of the order.


33/629


LPSCM 07 61 00 - 2

3.02 Storage

A. Store materials out of the weather in a clean, dry place. One end of each containershould be slightly elevated to allow any moisture to run off.

B. Panels and/or flashings with strippable film must not be stored in areas exposed tosunlight.

C. Care should be taken to prevent contact with any substance which may cause adiscoloration in the finish during storage.

D. Store materials to provide ventilation and prevent bending, abrasion, or Twisting.

3.03 Handling

A. Care should be taken to avoid gouging, scratching or denting.

B. Do not allow traffic on completed roof. If required, provide cushioned walk boards.

C. Protect installed products from damage caused by foreign objects and adjacentconstruction until completion of project.


4.01 Connection WorkThe applicator shall examine surfaces on which his work is to be applied, and shall notify thearchitect in writing if not suitable to receive his work. Work on any surface shall constituteacceptance of this surface by the installer.

4.02 Field MeasurementsTake field measurements to verify or supplement dimensions indicated prior to fabrication ofmetal panels.

4.03 Installation

A. Workmanship shall conform to standards set forth in the architectural sheet metalmanual as published by SMACNA.

B. Panels should be installed in such a manner that, horizontal lines are true and level, andvertical lines are plumb.

C. All starter and edge flashings should be installed prior to panels.

D. Do not allow panels or trim to come into contact with dissimilar materials.

E. Exposed edges are permissible due to the galvanic action of the system where the zincmigrates to protect the exposed material. However, efforts should be made to reducethe amount of exposed edges.

4.04 Touch –UpOnly minor scratches and abrasions will be allowed to be touched up. Any other damagedmaterial shall be replaced.

4.05 Clean Up

A. Leave work areas clean, free from grease, finger marks, and stains.

B. Remove scrap and debris from surrounding areas and grounds.



34/629


LPSCM 07 62 00 - 1

07 62 00 – FLASHING AND SHEET METAL TRIM

PART 1 – GENERAL

1.1 SECTION INCLUDES:

A. Shop or field-formed sh