logitech harmony 1100 logic board replacement · logitech harmony 1100 logic board replacement here...
TRANSCRIPT
-
Logitech Harmony 1100 Logic BoardReplacement
Here are the steps to replace the Logic Board in the Logitech Harmony 1100.
Written By: Chris Slack
Logitech Harmony 1100 Logic Board Replacement
iFixit CC BY-NC-SA www.iFixit.com Page 1 of 8
-
TOOLS:iFixit Opening Tools (1)
Phillips #00 Screwdriver (1)
JIS Driver Set (1)
J00 Philips Head Screwdriver (1)
Spudger (1)
Logitech Harmony 1100 Logic Board Replacement
iFixit CC BY-NC-SA www.iFixit.com Page 2 of 8
https://www.ifixit.com/Store/Parts/iFixit-Opening-Tool/IF145-335-2https://www.ifixit.com/Store/Parts/Phillips-00-Screwdriver/IF145-006-3http:/IF145-115-1file:///Item/J00_Philips_Head_Screwdriverhttp://www.ifixit.com/Tools/Spudger/IF145-002
-
Step 1 How to Open Logitech Harmony 1100
Remove battery cover, pushing down on circled areas and pushing outward
Remove battery by lifting up on corner exposed by indent in case
Step 2
Use a J0 screwdriver head
Remove 3 screws from batterycompartment
Logitech Harmony 1100 Logic Board Replacement
iFixit CC BY-NC-SA www.iFixit.com Page 3 of 8
-
Step 3
Open connector port on side
Remove screw with PH00 screwdriver head
Step 4
Use plastic opening tool to pry at the open slits on the side.
One or two silver foam cubes may pop out of the device. These belong in the slots shown in thethird picture. They do not need to go back until reassembly.
Also the plastic connector door will fall off. It will need to be put back upon reassembly.
Logitech Harmony 1100 Logic Board Replacement
iFixit CC BY-NC-SA www.iFixit.com Page 4 of 8
-
Step 5 Screen
Pop out plastic screen backing onfront of device.
Loosen screen backing by pushingback on plastic clips that are holdingthe black screen backing in place.
Logitech Harmony 1100 Logic Board Replacement
iFixit CC BY-NC-SA www.iFixit.com Page 5 of 8
-
Step 6
Use PH00 Phillips head from the iFixit Tool Kit to remove 3 screws from the circuit on the back halfof the device.
Flip over the larger circuit board to the left.
Use the edge of the circuit board to flip the board over.
The connector port in the top right corner may make removal difficult. Lift the logic board above thescrew ports, and the connector port should slide out easily.
Logitech Harmony 1100 Logic Board Replacement
iFixit CC BY-NC-SA www.iFixit.com Page 6 of 8
-
Step 7
Find the wire that attaches to the screen
Push dark grey bar that is used to lock the screen in place, outward from beige bar to disconnect.
Remove screen wire
Logitech Harmony 1100 Logic Board Replacement
iFixit CC BY-NC-SA www.iFixit.com Page 7 of 8
-
This document was last generated on 2017-06-18 01:50:05 AM.
Step 8 Logic Board
Push grey bar away from the beige bar
Remove button tab wire from logic board
Step 9
Lift on back of gold tab to unsecure positive and negative wires from device
Pull the gold buttons in towards the center of the device to detach logic board from case
Logitech Harmony 1100 Logic Board Replacement
iFixit CC BY-NC-SA www.iFixit.com Page 8 of 8
Logitech Harmony 1100 Logic Board ReplacementWritten By: Chris Slack
TOOLS:Step 1 How to Open Logitech Harmony 1100Step 2Step 3Step 4Step 5 ScreenStep 6Step 7Step 8 Logic BoardStep 9