localview - socomec...• run the application ./startapp.sh at this stage all localview services...
TRANSCRIPT
![Page 1: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/1.jpg)
LocalViewf o r L I N U X a n d M A C
Installation and operating manual EN
Manuel d’installation et d’utilisation FR
Manuale di installazione e uso IT
![Page 2: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/2.jpg)
2 LocalView - Ref.: IOMLOCVWXX01-EN 01
This SOCOMEC continuous power system is guaranteed against any manufacturing and material defects.
The warranty is valid for 12 (twelve) months from the date of commissioning, if activation is carried out by SOCOMEC personnel
or personnel from a support centre authorised by SOCOMEC, and no more than 15 (fifteen) months from the date of shipment by
SOCOMEC.
The warranty is valid throughout the country. If the UPS is exported abroad, the warranty will only cover the parts used to repair the fault.
The warranty is valid ex-works and covers labour and parts used to repair the fault.
The warranty shall not apply in the following cases:
• Failure due to accidents or force majeure (lightning, floods, etc.);
• Failure due to negligence or improper use (use outside tolerance limits: temperature, humidity, ventilation, electric power supply,
applied load, batteries);
• Insufficient or inadequate maintenance;
• Attempted maintenance, repairs or modifications not carried out by SOCOMEC personnel or personnel from a support centre
authorised by SOCOMEC.
• If the battery has not been recharged in accordance with the terms indicated on the packaging and in the manual, in cases of
extended storage or UPS inactivity.
SOCOMEC may, at its own discretion, opt for the repair of the product or the replacement of the faulty or defective parts with new
parts or used parts that are equivalent to new parts with regard to functions and performance.
Defective or faulty parts replaced free of charge shall become the property of SOCOMEC.
Replacements, repair of parts, or any modifications made to the product during the warranty period will not extend the duration of
the warranty.
SOCOMEC shall not be responsible for damages under any circumstances (including and without limitations, damage for loss of
earnings, interruption of activity, loss of information or other financial losses) resulting from the use of the product.
These conditions are subject to Italian law. Any disputes fall under the jurisdiction of the Court of Vicenza.
CERTIFICATE AND CONDITIONS OF WARRANTY
SOCOMEC retains the full and exclusive ownership rights over this document. Only a personal right to use the document for the
application indicated by SOCOMEC is granted to the recipient of the document. The reproduction, modification, distribution of this
document, partially or fully and in any way, is expressly prohibited except upon Socomec’s express prior written consent.
This document is not a specification. SOCOMEC reserves the right to make any changes to information without prior notice.
![Page 3: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/3.jpg)
3LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
CONTENTS
EN
GL
ISH
1. SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. LOCAL VIEW FOR LINUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1. COMPATIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2. INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3. COMMUNICATION CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4. RUNNING LOCAL VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5. NOTIFICATION UTILITY INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.6. LOCAL VIEW UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3. LOCAL VIEW FOR COMPUTER WITH MAC OS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1. COMPATIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2. INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.3. COMMUNICATION CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.4. RUNNING LOCAL VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.5. STARTING APPLICATION ON A MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.6. NOTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.7. LOCALVIEW UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4. USER INTERFACE WEB PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.1. GENERAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.2. SERVICE AND UPS STATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.3. USER INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5. EXPERT LOCALVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.1. MENU NAVIGATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.2. MEASUREMENTS HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.3. EVENT LOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.4. EMAIL CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.5. SHUTDOWN CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.6. USER CONFIGURATION - MISCELLANEOUS . . . . . . . . . . . . . . . . . . . . . . . . 30
5.7. COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
![Page 4: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/4.jpg)
4 LocalView - Ref.: IOMLOCVWXX01-EN 01
UPS monitoring
• Simple user interface
- UPS status
- Battery status and measurements
- Load status and measurements
• Expert level access for :
- UPS events history log
- Measurements history log
- Configuration
- Email notification
- Shutdown procedure
- Miscellaneous (language, serial port, log filter)
Alert notification via email
• Simple user interface
• Multiple recipients
Automatic shutdown procedure
• Event selection
• Batch and shutdown timing
UPS communication with the server/Mac
• RS232
• USB
• Ethernet
1. SUMMARY
1-1
![Page 5: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/5.jpg)
5LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
EN
GL
ISH
2.1. COMPATIBILITY
HARDWARE COMPATIBILITY
LocalView runs on x86 / x64 platform.
A serial port, USB port or Ethernet connection is required depending on the UPS model.
LIST OF TESTED LINUX DISTRIBUTION
• UBUNTU
• DEBIAN
• REDHAT
• SUSE
WEB BROWSER COMPATIBILITY
The LocalView user interface is provided via web server, included in the LocalView package.
LocalView is compatible with:
• Mozilla
• Safari
• Chrome
2.2. INSTALLATION
USER ACCOUNT
It is necessary to install LocalView software with the administrator account as the root user.
2. LOCAL VIEW FOR LINUX
![Page 6: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/6.jpg)
6 LocalView - Ref.: IOMLOCVWXX01-EN 01
2. LOCAL VIEW FOR LINUX
LOCALVIEW PACKAGE
Copy the LocalView package from CD or the SOCOMEC website to LINUX disk (i.e. the user /Documents standard directory).
Extract gz.tar file via file manager or via Terminal.
tar –zxvf L32_Package_xxx
tar –zxvf L64_Package_xxx
After unzipping, the setup and localview folders are present in the same directory.
2.2-1
./install.sh to install LocalView, then LocalView is installed in '/usr/Socomec UPS/LocalView' folder by default.
WARNING!
Do not change the default installation directory.
2.2-2
2.3. COMMUNICATION CHANNEL
LocalView communicates via RS232, USB or Ethernet. Ensure the port provided for LocalView is available.
If a USB/R232 converter is used, the device has to be installed beforehand (please refer to the manufacturer's website for the
driver). The resource is /dev/ttyUSB0 in this case.
You can check the list of devices with the following shell command: dmesg | grep tty
SETTINGS IN THE CASE OF ETHERNET CONNECTION:
UPS Protocol type: VU-MAP for ITYS PRO UPS range
IP address: UPS address (to check on the UPS mimic panel)
Port: 1025.
![Page 7: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/7.jpg)
7LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
2. LOCAL VIEW FOR LINUX
2.4. RUNNING LOCAL VIEW
MANUALLY VIA TERMINAL
• Open a terminal session
• Select the installation folder : cd '/usr/Socomec UPS/LocalView'
• Run the application ./StartApp.sh
At this stage all LocalView services will be running.
RUNNING LOCALVIEW AS A DEMON
If LocalView is installed as a demon all services will be running when LINUX is starting up. It is not necessary to open a session to run it.
EXAMPLE OF INSTALLATION:
UBUNTU / DEBIAN
Edit the following file using root rights: /etc/rc.local
Add this line before the exit 0 command: sh '/usr/Socomec UPS/LocalView/StartApp.sh' &
REDHAT
Edit the following file using root rights: /etc/rc.d/rc.local
Add this line before the exit 0 command: sh '/usr/Socomec UPS/LocalView/StartApp.sh' &
SUSE
Edit the following file using root rights: /etc/init.d/after.local
Add this line before the exit 0 command: sh '/usr/Socomec UPS/LocalView/StartApp.sh' &
After saving the file it is necessary to restart LINUX to start LocalView as a demon.
OPENING THE USER INTERFACE
Start the web browser and open the LocalView home page with this link: http://localhost/8080/index.html
Port 8080 is set by default. It is possible to change the port on the LocalView Expert Miscellaneous page.
Communication with the UPS is not open the first time.
Select the LocalView Expert link to switch to configuration pages.
2.4-1
Select CONFIGURATION menu, and Communication slide.
![Page 8: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/8.jpg)
8 LocalView - Ref.: IOMLOCVWXX01-EN 01
2. LOCAL VIEW FOR LINUX
• Select the interface:
- USB for NETYS UPS range
The protocol is set to PH
- Serial for other UPS models
• Select the Protocol and serial configuration:
Select the protocol: JBUS-P
Slave ID: set to 1 by default
COM speed: 9600 by default.
• ETH (Ethernet)
- Select the protocol: VU-MAP for ITYS PRO
- IP address of the UPS
- Port: 1025
• Save the parameter
At the end of the procedure communication starts.
The UPS status is displayed on the page header.
2.5. NOTIFICATION UTILITY INSTALLATION
LocalView includes a notification application. This application is an external tool based on the Desktop Graphical Interface
currently used by the system, such as GNOME or KDE.
Two specific tools can be used depending on the LINUX distribution and the application:
• GNOME/UNITY environment > '/usr/Socomec UPS/LocalView/StartMenuBar_Gnome.sh'
• KDE environment > '/usr/Socomec UPS/LocalView/StartMenuBar_KDE.sh'
IMPORTANT PREREQUISITE!
The MenuBar application requires these system tools to be installed:
GNOME/UNITY environment > notify-send
KDE environment > kdialog
Usually these tools are present by default on the system. If not they must be installed, which can be implemented
using the standard software management present on the Linux System.
See the following steps for automatic startup of the notification program.
![Page 9: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/9.jpg)
9LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
2. LOCAL VIEW FOR LINUX
2.5-2
2.5-1
UBUNTU (GNOME/UNITY)
Start the application Startup Applications
Click on Add and select the required application.
![Page 10: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/10.jpg)
10 LocalView - Ref.: IOMLOCVWXX01-EN 01
REDHAT (GNOME)
Run the application gnome-session-properties manually (using ALT + F2).
2. LOCAL VIEW FOR LINUX
2.5-3
2.5-4
Click on Add and select the required application.
DEBIAN (GNOME)
Go to the menu SYSTEM > PREFERENCES > STARTUP APPLICATIONS
Click on Add and select the required application.
![Page 11: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/11.jpg)
11LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
2. LOCAL VIEW FOR LINUX
Start the application Autostart.
2.5-5
2.5-6
Click on Add script and select the required application.
SUSE (KDE)
Start the application Autostart
Click on Add script and select the required application.
![Page 12: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/12.jpg)
12 LocalView - Ref.: IOMLOCVWXX01-EN 01
NOTIFICATION
Notification is only displayed if a session is open.
This application is started when a new session is open and stopped when closed.
Notification relates to UPS STATUS, and SHUTDOWN PROCEDURE. Normal status is not notified.
Example of notification display web page.
2. LOCAL VIEW FOR LINUX
2.5-7
Bear in mind that notification pops up in different Linux distributions. Layout and position may differ.
NOTIFICATION LIST
Status Description
No communication with UPS No communication with UPS
Shutdown procedure in progress Shutdown procedure in progress
UPS Off or Imminent Stop UPS Off or Imminent Stop
UPS on Standby
Alarm Present or On Bypass Alarm Present or On Bypass
NORMAL MODE / eco MODE Normal Mode
Expert / Viewer Link Button Switch to Expert or Viewer program
2.6. LOCAL VIEW UPDATE
LocalView makes it possible to access the SOCOMEC SOFTWARE website to download the latest release of LocalView if required.
When a new release is installed all previous configuration and log files are kept. It is not necessary to configure the LocalView
environment again.
![Page 13: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/13.jpg)
13LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
3. LOCAL VIEW FOR COMPUTER WITH MAC OS
3.1. COMPATIBILITY
HARDWARE COMPATIBILITY
LocalView runs on the APPLE platform.
A serial port or USB port is required depending on the UPS model. With a serial connection the RS232/USB converter is mandatory.
Recommended converter: PROLIFIC TECHNOLOGY USB/RS232 Converter.
MAC OS COMPATIBILITY
• YOSEMITE
WEB BROWSER COMPATIBILITY
The LocalView user interface is provided via web server, included in the LocalView package.
LocalView is compatible with:
• Safari
• Chrome
3.2. INSTALLATION
USER ACCOUNT
It is necessary to install LocalView software with the administrator account.
LOCALVIEW PACKAGE
Copy the LocalView package (LocalView_Mac_xxx.mpkg) from CD or SOCOMEC website to MAC disk
Double click on the file to install LocalView and follow the standard installation tools.
3.2-1
![Page 14: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/14.jpg)
14 LocalView - Ref.: IOMLOCVWXX01-EN 01
3. LOCAL VIEW FOR COMPUTER WITH MAC OS
3.3. COMMUNICATION CHANNEL
LocalView communicates via RS232 or USB. Ensure the port provided for LocalView is available.
If using a USB/R232 converter the device has to be installed beforehand.
The resource is /dev/tty.usbserial in this case.
Checking the driver: Select about in MAC system, info menu and system report.
In the HW list device check on USB item if the device is present and running.
3.4. RUNNING LOCAL VIEW
RUNNING LOCALVIEW AS A SERVICE
It runs automatically as a service. When the MAC restarts, LocalView starts as well.
OPENING THE USER INTERFACE
Start the web browser and open the LocalView home page with this link: http://localhost/8080/index.html
Port 8080 is set by default. It is possible to change the port on the LocalView Expert page.
Communication with the UPS is not open the first time.
Select the LocalView Expert link to switch to configuration pages.
3.4-1
Select CONFIGURATION menu and Communication slide.
• Select the interface
- USB for NETYS UPS range
The protocol is set to PH
- Serial for other UPS models
• Select the Protocol and serial configuration
- Select the protocol : JBUS-P
- Slave ID : set to 1 by default
- COM speed: 9600 by default.
• ETH (Ethernet)
- Select the protocol: VU-MAP for ITYS PRO
- IP address of the UPS
- Port: 1025
• Save the parameter
At the end of the procedure communication starts.
The UPS status is displayed on the page header.
![Page 15: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/15.jpg)
15LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
3. LOCAL VIEW FOR COMPUTER WITH MAC OS
3.5. STARTING APPLICATION ON A MAC
• Using the icon on MenuBar
3.5-1
3.5-2
3.5-3
• Using the APP on Application Folder
• Using the APP on LaunchPad
![Page 16: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/16.jpg)
16 LocalView - Ref.: IOMLOCVWXX01-EN 01
3.6. NOTIFICATION
LocalView includes a notification application.
On the MAC MenuBar a new icon is added. This icon gives access to LocalView Viewer and LocalView Expert pages, as described
in the previous paragraph. This icon flashes during UPS event notification or the shutdown procedure.
Clicking opens the MenuBar (see figure 3.5-1).
The first line gives UPS status, and the second part accesses LocalView interfaces.
NOTIFICATION
Status Description
Service stopped Service Stopped
No communication with UPS No communication with UPS
Shutdown procedure in progress Shutdown procedure in progress
UPS Off or Imminent Stop UPS Off or Imminent Stop
UPS on Standby
Alarm Present or On Bypass Alarm Present or On Bypass
NORMAL MODE / eco mode Normal Mode
3.7. LOCALVIEW UPDATE
LocalView makes it possible to access the SOCOMEC SOFTWARE website to download the latest release of LocalView if required.
When a new release is installed all previous configuration and log files are kept. It is not necessary to configure the LocalView envi-
ronment again.
3. LOCAL VIEW FOR COMPUTER WITH MAC OS
![Page 17: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/17.jpg)
17LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
4. USER INTERFACE WEB PAGE
The following chapter is common to LINUX and MAC.
The user interface is identical for both platforms.
4.1. GENERAL OVERVIEW
4.1-1
4.2-1
The top bar of the page gives UPS status, load rate and remaining backup time.
During the shutdown procedure these parameters are replaced with shutdown procedure status, including the remaining time
before shutdown.
4.2. SERVICE AND UPS STATUS
UPS STATUS
When running, an icon is present in the top area of the Viewer or Expert
Icon colour defines the service and UPS status, for example:
Status Icon Description
Service Stopped Service Stopped
No communication with UPS No communication with UPS
Shutdown procedure in progress Shutdown procedure in progress
UPS Off or Imminent Stop UPS Off or Imminent Stop
UPS on Standby
Alarm Present or On Bypass Alarm Present or On Bypass
NORMAL MODE / eco mode Normal Mode
![Page 18: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/18.jpg)
18 LocalView - Ref.: IOMLOCVWXX01-EN 01
4. USER INTERFACE WEB PAGE
UPS PARAMETERS
Load rate and remaining backup time are displayed on the status bar. Values are automatically refreshed when updated.
If the remaining backup time is not available from the UPS the label and value are disabled.
EXPERT / VIEWER HYPERLINK
This link switches from Local View viewer to Expert mode and vice versa.
4.3. USER INTERFACE
1 UPS REFERENCE
Name and picture of the UPS connected to the server/Mac.
LIST OF UPS SYSTEMS
MODULYS 1/1
NETYS PE
NETYS PL
NETYS PR
ITYS
NETYS RT
Note: the UPS picture is approximate and may differ from the actual UPS connected to the server/Mac.
2 UPS STATUS
![Page 19: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/19.jpg)
19LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
Status Type of info Reason
AlarmThe UPS output will be switched OFF due to a
critical alarm(1)
Alarm AC failure
StatusServer/Mac powered by the mains, and Inverter
automatically switched on when AC failed
Status Server/Mac powered by mains(1)
Status Server/Mac protected by UPS(1)
Status Server/Mac not powered and awaiting reactivation
Status Server/Mac not supplied(1)
(1). Not available for Netys PE and Netys PL.
3 BATTERY BACKUP TIME
The remaining backup time is displayed in minutes, and automatically updated when the value changes.
Depending on the UPS range, backup time is only calculated when the UPS switches to the battery; otherwise the value is not
displayed.
4.3-1
4. USER INTERFACE WEB PAGE
![Page 20: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/20.jpg)
20 LocalView - Ref.: IOMLOCVWXX01-EN 01
4. USER INTERFACE WEB PAGE
4 BATTERY STATUS
Symbol Status Value
Battery not connected or
UPS ON BYPASS(1)
BATTERY LOW
BATTERY DISCHARGED(1)
BATTERY DISCHARGING
BATTERY CHARGING(1)
BATTERY CHARGED(1)The level represents % capacity.
From 60 to 100%.
(1). Not available for Netys PE and Netys PL.
5 BATTERY CAPACITY
The battery capacity (in %) is displayed if the measurement is calculated by the UPS, otherwise the battery voltage is displayed.
6 BATTERY TEST BUTTON
LocalView can test the battery. If isn’t available battery testing is not possible or has been disabled by the UPS.
Battery test status and results are displayed on the ALARM bar (8).
![Page 21: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/21.jpg)
21LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
4. USER INTERFACE WEB PAGE
BATTERY STATUS
Battery OK(1)
Battery alarm
Battery Test alarm(1)
Battery test in progress
(1). Not available for Netys PE and Netys PL
7 LOAD STATUS
The blue tank represents the % of UPS load rate:
In the event of overload ( Load rate > 100%) the tank is yellow :
4.3-2
8 BATTERY STATUS & ALARM BAR
When a UPS alarm occurs it is displayed and the Alarm ACK button appears . If there are several alarms, they are displayed
consecutively.
LIST OF ALARMS
END BACKUP TIME
BATTERY ALARM
GENERAL ALARM
OVER TEMPERATURE (1)
OVERLOAD (1)
(1) Not available for Netys PE and Netys PL
![Page 22: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/22.jpg)
22 LocalView - Ref.: IOMLOCVWXX01-EN 01
4. USER INTERFACE WEB PAGE
9 ACK BUTTON
When a new alarm occurs the buzzer sounds on the UPS. Selecting sends a command to stop the buzzer.
Example of the User Interface with a general UPS alarm:
4.3-3
![Page 23: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/23.jpg)
23LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
5. EXPERT LOCALVIEW
5.1. MENU NAVIGATION
• Accesses the measurements history
• Accesses the event log (Status and Alarms)
• SMTP and Email configuration
• Server/Mac Shutdown configuration
• Miscellaneous item:
- Language selection
- Log filter and sample settings
- Automatic update settings
• UPS communication port settings
5.2. MEASUREMENTS HISTORY
5.2-1
Press the left or right arrows to move to the previous or following measurements log pages.
![Page 24: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/24.jpg)
24 LocalView - Ref.: IOMLOCVWXX01-EN 01
5. EXPERT LOCALVIEW
LIST OF MEASUREMENTS STORED
Measurements Format
UPS Load Rate %
Output voltage V (L1, L2, L3 if triphases)
Battery capacity %
Battery voltage V
Input voltage V (L1, L2, L3 if triphases)
The number of samples depends on logging filters set on the miscellaneous page.
Default setting: Records by WEEK, 10 minute sampling.
The oldest record is replaced with the newest (FIFO). Maximum no. of records allowed: ~ 1500.
EXPORT
This option saves the entire measurements history in CSV format to the local disk. It is possible to open this file using an external
tool for diagnostic purposes if required. It can also be used as backup.
5.3. EVENT LOG
LocalView creates a history log with the most important statuses and alarms.
Each new event is dated and stored in a file.
5.3-1
![Page 25: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/25.jpg)
25LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
EN
GL
ISH
LIST OF EVENTS STORED:
STATUS TYPE
Imminent Stop ALARM
On Battery ALARM
End Backup Time ALARM
Battery Alarm ALARM
General Alarm ALARM
Over Temperature ALARM
Overload ALARM
Battery Test Alarm ALARM
Battery Test In Progress STATUS
Battery OK STATUS
eco MODE STATUS
Bypass Mode STATUS
Normal Mode STATUS
Standby Mode STATUS
Off STATUS
EVENTS FILTERING
5. EXPERT LOCALVIEW
5.3-2
It is possible to select different event periods, for example:
Last 7 days shows events recorded for the last seven days.
All disables the current filter.
EXPORT
This option saves the entire event log in CSV format to the local disk. It is possible to open this file using an external tool for diagnostic
purposes if required. It can also be used as backup. The recommended default file name is: EventsLog_ddMMyy_HHmm.csv,
where dd = day; MM = month; yy = year, HH = hour (24h format); mm = minutes.
![Page 26: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/26.jpg)
26 LocalView - Ref.: IOMLOCVWXX01-EN 01
5.4. EMAIL CONFIGURATION
LocalView can send notification according to different events. It is possible to select events, level of criticality and up to 8 recipients.
This process is managed by the service. It is not necessary to have the User Interface open.
5.4-1
SMTP SERVER CONFIGURATION
Defines mail server network configuration
- In the case of a company mail server
- In the case of external providers' mail server
- Account configuration
EVENTS
Click inside the box to enable the event that will send an email.
RECIPIENTS
The recipient address format is: name@domain
The description field is only for information, it is not included in the email body.
Level of criticality: Info = All enabled events
Warning = Warning + Critical events
Critical = only Critical events
SEND A TEST EMAIL
Sends a test email to check the mail server configuration (SMTP).
5. EXPERT LOCALVIEW
![Page 27: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/27.jpg)
27LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
EN
GL
ISH
5.4-2
UPS New Events
LocalViewNetys
L a s t E v e n t s t r i g g e r e d :
G e n e r a l A l a r m
E v e n t s s t i l l a c t i v e :
O v e r l o a d
O v e r Te m p e r a t u r e
5. EXPERT LOCALVIEW
CRITICALITY MANAGEMENT
The different levels are :
• Info
• Warning
• Critical
The recipient will only receive an email event from the minimum level selected. For example:
• Critical = Only Critical level
• Warning = Critical + Warning levels
• Info = Info + Warning + Critical levels
DELAY MANAGEMENT
Delays and repetitions are set to 0 by default. If events occur emails are sent immediately without repetitions.
LocalView sends notification after a delay, which is set in hours. If the event is still present email notification is sent at the end of the period.
countdownevent present
delayreached
repetition event no longer
present
email issue
process
new event
General case:
notification
event cancelled
EMAIL FORMAT
eMail subject :
UPS New Events
UPS Events Cancelled
UPS Events Notification
Email message:
New Events:
Events Cancelled:
Events Active:
![Page 28: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/28.jpg)
28 LocalView - Ref.: IOMLOCVWXX01-EN 01
5. EXPERT LOCALVIEW
5.5. SHUTDOWN CONFIGURATION
LocalView can shut the Server/Mac down. It is possible to select events, delays, and shutdown commands.
This process is managed by the service. It is not necessary to have the User Interface open.
If a script file is present it should be executed before shutdown. It must be created before setting the shutdown parameters.
5.5-1
SHUTDOWN EVENTS
This table illustrates the server/Mac shutdown and timing procedure.
Events Warning interval Delay before executing the script Delay before OS shutdown
On Battery
Fixed at 30 seconds
First delay Shutdown delay
0 = Immediate
Range from 1’ to 60’
Overload
Over Temperature
Battery Low
Imminent Stop
On Bypass
![Page 29: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/29.jpg)
29LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
EN
GL
ISH
5. EXPERT LOCALVIEW
SHUTDOWN TIMING
CASE 1:
No shutdown
CASE 2:
Shutdown process
Event
Detection
First
notificationFirst delay countdown
End delay:
Script
execution
Shutdown
delay
countdown
End delay:
Server/Mac
Shutdown
SCRIPT SETTINGS
Click on the box to activate this function.
Select the script/batch file to be executed, via the file explorer.
SHUTDOWN COMMAND
Click on the box to enable shutdown.
UPS SHUTOFF
LocalView sends a delayed UPS shutoff when the Server/Mac shutdown is starting, and only in the event of a battery alarm. The
UPS shuts off when the countdown is completed.
This function isn’t available for all UPS systems (Refer to your UPS manual).
TEST SHUTDOWN PROCEDURE
LocalView checks procedure and timing via AC Fail/ On battery status simulation.
It is possible to cancel this procedure during the shutdown countdown.
The UPS shutoff will not be executed in this case for safety reasons.
![Page 30: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/30.jpg)
30 LocalView - Ref.: IOMLOCVWXX01-EN 01
5. EXPERT LOCALVIEW
USER NOTIFICATION
During the shutdown procedure UPS status is replaced with shutdown status, the reason, and countdown notification. This notifica-
tion is refreshed every 30s. The countdown indicates the remaining time in seconds before Server/MAC shutdown.
Shutdown Status includes:
- Shutdown warning
- Shutdown cancelled
- Shutdown in progress
5.6. USER CONFIGURATION - MISCELLANEOUS
5.6-1
LANGUAGE
The User Interface goes to English by default. It is possible to change the language by selecting the text.
FILTER
The filter defines the period and sample time for the measurements history.
Detailed record table:
Sample in minutes DAY WEEK MONTH
1 1440
2 720
5 288
10 144 1008
20 72 504
30 48 336 1488
60 24 168 744
HTTP PORT
It is possible to change the HTTP port of the application. If changed, it is necessary to reload the webpage at the new port.
I.E.: httpport = 8081
New link = http://localhost:8081/index.html
![Page 31: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/31.jpg)
31LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
EN
GL
ISH
5. EXPERT LOCALVIEW
UPDATE
Press the Check for updates button to check for new updates. If present a link-message
will notify you of the presence of new packages. Click on it to access the Socomec software download page.
5.6-2
![Page 32: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/32.jpg)
32 LocalView - Ref.: IOMLOCVWXX01-EN 01
5.7-1
5.7. COMMUNICATION
In the event of a UPS port connection modification on your Server/Mac the communication settings can be changed. Select the
correct communication port and settings manually.
• Select the interface:
- USB for NETYS UPS range
The protocol is set to PH
- Serial for other UPS models
• Select the Protocol and serial configuration:
Select the protocol: JBUS-P
Slave ID: set to 1 by default
COM speed: 9600 by default.
• ETH (Ethernet)
- Select the protocol: VU-MAP for ITYS PRO
- IP address of the UPS
- Port: 1025
5. EXPERT LOCALVIEW
![Page 33: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/33.jpg)
33LocalView - Ref.: IOMLOCVWXX01-EN 01
EN
GL
ISH
6. TROUBLESHOOTING
Page not found – Error 404 when LocalView html page is requested
Case 1
LocalView service is not stated. Check if the process is present in Linux (ps – all) and if the application is running on
MAC. Restart Local View.
Case 2:
The http port has been changed or the default port is not accessible.
It must be changed manually in UserPlantConf.xml. Local View has to be restarted.
The LocalView Status icon is blue
No communication with UPS. Check the cable, communication setting and UPS connection.
There is no button
Battery testing is not available, or has been disabled by the UPS
When I click on nothing happens
The battery test has been cancelled, or has been suspended by the UPS
When I click on the buzzer still sounds on the UPS
It is possible that a new alarm is occurring at the same time. The buzzer must be stopped directly on the UPS.
There is no button
The command has been sent, or the alarm is no longer present
I haven’t received an email
Check the SMTP configuration.
Test the send email function
Check that events have been enabled
The script file has not been executed
Check if the command file is already present on the disk, in the correct folder.
Manually test this script file.
Test this file with the shutdown test procedure function.
Shutdown hasn’t been completed
Check if the shutdown command is present on the configuration page.
Manually check if the command has been executed (command script shell)
Check if the shutdown command option is correct
The service doesn’t start automatically
Check your RC configuration. Try to start it manually.
I cannot change the language
Not all languages are available. Select the UK version. If nothing changes close LocalView and run it again.
The log file is empty
Maybe nothing has happened today. Select the Last 7 days or All filter option if events have been stored.
The measurements history is empty
Check the record sample via the configuration page, and check communication with the UPS.
Click on Export if data is stored in the file.
Close LocalView and open it again.
![Page 34: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/34.jpg)
![Page 35: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/35.jpg)
![Page 36: LocalView - Socomec...• Run the application ./StartApp.sh At this stage all LocalView services will be running. RUNNING LOCALVIEW AS A DEMON If LocalView is installed as a demon](https://reader034.vdocuments.site/reader034/viewer/2022050419/5f8ed412cc09b244bd230ab3/html5/thumbnails/36.jpg)
*IOMLOCVWXX01-EN 01*IOMLOCVWXX01-EN 01 10.2015
www.socomec.com
HEAD OFFICE
SOCOMEC GROUPS.A. SOCOMEC capital 10 816 800€ R.C.S. Strasbourg B 548 500 149 B.P. 60010 - 1, rue de Westhouse F-67235 Benfeld Cedex - FRANCE Tel. +33 3 88 57 41 41 Fax +33 3 88 74 08 00 [email protected]
Socomec worldwide
BELGIUM
SolarTel. +32 2 340 02 30 Fax +32 2 346 28 99 [email protected]
FRANCE
SolarTel. +33 1 45 14 63 00 Fax +33 1 48 67 31 12 [email protected]
GERMANYPower Control & Energy EfficiencyTel. +49 7243 65292 0 Fax +49 7243 65292 13 [email protected]. +49 621 71 68 40 Fax +49 621 71 68 444 [email protected]
ITALYPower Control & Energy EfficiencyTel.+39 02 98 49 821 Fax +39 02 98 24 33 10 [email protected]. +39 0444 598611 Fax +39 0444 598627 [email protected] Tel.+39 02 98 242 942 Fax +39 02 98 240 723 [email protected]
NETHERLANDS
SolarTel. +31 30 760 0900 Fax +31 30 637 2166 [email protected]
POLANDPower Control & Energy EfficiencyTel. +48 91 442 64 11 Fax +48 91 442 64 19 [email protected]. +48 22 825 73 60 Fax. +48 22 825 73 60 [email protected]
PORTUGALUPS / SolarTel.+351 261 812 599 Fax +351 261 812 570 [email protected]
ROMANIA
SolarTel. +40 21 319 36 88 Fax +40 21 319 36 89 [email protected]
RUSSIA
SolarTel. +7 495 775 19 85 Fax +7 495 775 19 85 [email protected]
SLOVENIA
SolarTel. +386 1 5807 860 Fax +386 1 561 11 73 [email protected]
SPAIN
SolarTel. +34 93 540 75 75 Fax +34 93 540 75 76 [email protected]
UNITED KINGDOMPower Control & Energy EfficiencyTel. +44 1462 440 033 Fax +44 1462 431 143 [email protected].+44 1285 863 300 Fax+44 1285 862 304 [email protected]
TURKEY
SolarTel. +90 216 540 71 20-21-22 Fax +90 216 540 71 27 [email protected]
YOUR DISTRIBUTOR
IN ASIA PACIFIC
AUSTRALIAUPSTel. +61 2 9325 3900 Fax +61 2 9888 9544 [email protected]
CHINAUPS / Power Control & Energy EfficiencyTel. +86 21 52 98 95 55 Fax +86 21 62 28 34 68 [email protected]
INDIAPower Control & Energy EfficiencyTel. +91 124 4027210 Fax +91 124 4562738 [email protected]
Tel. +91 44 39215400 Fax +91 44 39215450 & 51 [email protected] [email protected]
SINGAPORE UPS / Power Control & Energy EfficiencyTel.+65 6506 7600 Fax +65 64 58 7377 [email protected]
THAILANDUPSTel. +66 2 941 1644 7 Fax +66 2 941 1650 [email protected]
VIETNAMUPSTel. +84 8 3559 1220 Fax +84 8 3559 1221 [email protected]
IN MIDDLE EAST
UNITED ARAB EMIRATES
SolarTel.+971 4 29 98 441 Fax +971 4 29 98 449 [email protected]
IN AMERICA
USA, CANADA & MEXICOPower Control & Energy EfficiencyTel. +1 617 245 0447 Fax +1 617 245 0437 [email protected]
OTHER COUNTRIES
NORTH AFRICAAlgeria / Morocco / [email protected]
AFRICAOther [email protected]
SOUTH EUROPECyprus / Greece / Israel / [email protected]
SOUTH AMERICATel. +34 93 540 75 75 [email protected]
MORE DETAILSwww.socomec.com/worldwide
IN EUROPE