loader nual - woods equipment company · the bale spear is to be used only for handling bales. do...

OP

ER

AT

OR

'S M

AN

UA

L

LOADERM

AN

0553

(R

ev. 8

/1/2

012)

LC96LC96-2

Tested. Proven. Unbeatable.

2 Introduction Gen’l (Rev. 12/5/2011)

TO THE DEALER:

Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructionsand safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manualare completed before releasing equipment to the owner.

The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies thatall Dealer Check List items have been completed. Dealers can register all Woods product atdealer.WoodsEquipment.com under Product Registration.

Failure to register the product does not diminish customer’s warranty rights.

TO THE OWNER:

Read this manual before operating your Woods equipment. The information presented will prepare you to do a better andsafer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and becomeacquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can beobtained from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or inthe United States and Canada call 1-800-319-6637.

The equipment you have purchased has been carefully engineered and manufactured to provide dependable andsatisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.Observe all safety information in this manual and safety decals on the equipment.

For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessarytools and equipment to handle all your needs.

Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required forsafe and satisfactory operation. Record the model number and serial number of your equipment in the spacesprovided:

Model: _______________________________ Date of Purchase: _____________________

Serial Number: (see Safety Decal section for location) ____________________________________

Provide this information to your dealer to obtain correct repair parts.

Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment.The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle withan exclamation mark) to indicate the degree of hazard for items of personal safety.

Introduction 3MAN0553 (2/23/2007)

TABLE OF CONTENTSIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Safety & Instructional Decals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Owner Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Dealer Check Lists. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Parts Lists

LC96, LC96-2 Loader Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 - 37LC96, LC96-2 Hydraulic Cylinder Seal Kits . . . . . . . . . . . . . . . . . . . . . 38 LC96, LC96-2 Hydraulic Hose Routing & Parts List . . . . . . . . . . . . . . . 38Quick Attach Bucket Assembly / Pin-on Bucket Assembly . . . . . . . . . . 39Quick Attach Coupler (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Bolt Torque Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Bolt Size Chart & Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Replacement Parts Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Product Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

GENERAL INFORMATIONThe purpose of this manual is to assist you in operatingand maintaining your loader. Read it carefully. Itfurnishes information and instructions that will help youachieve years of dependable performance. Theseinstructions have been compiled from extensive fieldexperience and engineering data. Some informationmay be general in nature due to unknown and varyingoperating conditions. However, through experienceand these instructions, you should be able to developprocedures suitable to your particular situation.

The illustrations and data used in this manual werecurrent at the time of printing, but due to possible inlineproduction changes, your machine may vary slightly indetail. We reserve the right to redesign and change themachines as may be necessary without notification.

Throughout this manual, references are made to rightand left directions. These are determined by standingbehind the equipment facing the direction of forwardtravel.

(Rev. 8/1/2012)

4 Introduction MAN0553 (2/23/2007)

SPECIFICATIONSSpecifications will vary with tractor, tire size, hydraulic system and bucket used. The specifications are given for aloader equipped with a 66" material bucket, operated with an average tractor hydraulic system of 4-10 gpm with engineoperating at rated PTO rpm and a control valve relief setting of 2150 psi.

Model LC96, LC96-2

A Maximum Lift Height 96"B Clearance with Attachment Dumped 74"C Reach at Maximum Height 25"D Maximum Dump Angle 45°E Reach with Attachment on Ground 64"F Attachment Rollback Angle 25°G Digging Depth 6"

Overall Height in Carrying Position 54"Length of Attachment 24"Lift Capacity to Full Height at Bucket Pin 1200 lbs.Lift Capacity to Full Height - 19.7" Forward of Bucket Pin 900 lbs.Breakout Force at Bucket Pin 2150 lbs.Breakout Force - 19.7" Forward of Bucket Pin 1650 lbs.System Pressure Tested 2150 psiRecommended Hydraulic Flow 4-10 gpmRecommended Tractor PTO Horsepower 20-35 hpLift Cylinder Bore 1.77"Bucket Cylinder Bore 2.76"

BUCKET HEAPED CAPACITY WEIGHT

60" QA & Pin 9.4 cu. ft. 190 lbs.66" QA & Pin 10.4 cu. ft. 200 lbs.

(Rev. 8/1/2012)

Introduction 5MAN0553 (2/23/2007)

LIFT CAPACITY & BREAKOUT VS PRESSUREPressure

(psi) LC96, LC96-2

Lift Capacityat Bucket Pin (lbs.)

1900 1025

2150 1200

2400 1375

Breakout19.7" Forward of Bucket

Pin (lbs.)

1900 1425

2150 1650

2400 1875

Capacities measured in accordance with ASAE S301.4

SKID STEER ATTACHMENTS APPROVED FOR USE ON LC96, LC96-2 LOADERS

Description Model Heaped Capacity Weight

60" Manure Fork MF6000 --- 349 lbs.

Agricultural GrappleAttachment

GF3000 --- 260 lbs.

Bale Spear BS3100 2200 lbs. 207 lbs.

Pallet Fork w/46" Pivoting Teeth PF17 1700 lbs. 382 lbs.

Pallet Fork w/36" Lock Down Teeth DF3600 3430 lbs. 394 lbs.



(Rev. 8/1/2012)

6 Safety 1020 Loader SR (Rev. 2/16/2007)

INSTALLATIONDuring installation, the tractor engine should be

off, the key removed and the brakes locked. Do notdisconnect hydraulic lines until attachments areremoved or lowered to the ground and systempressure is released by operating valve levers.Never operate any hydraulic cylinders during anyphase of the installation process.

After connecting hoses, check that all controllever positions function as instructed in the Opera-tor's Manual. Do not put into service until controllever and equipment movements are correct.

TRAININGSafety instructions are important! Read all

attachment and power unit manuals; follow allsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer. To locate your nearest dealer, checkthe Dealer Locator at www.mccormickusa.com, orin the United States and Canada call 1-866-924-4733.) Failure to follow instructions or safety rulescan result in serious injury or death.

If you do not understand any part of this manualand need assistance, see your dealer.

Know your controls and how to stop engine andattachment quickly in an emergency.

Operators must be instructed in and be capableof the safe operation of the equipment, its attach-ments, and all controls. Do not allow anyone tooperate this equipment without proper instruc-tions.

Keep hands and body away from pressurizedlines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety goggles.

Hydraulic fluid under pressure can easily penetrateskin and will cause serious injury or death.

Make sure that all operating and service person-nel know that if hydraulic fluid penetrates skin, itmust be surgically removed as soon as possible bya doctor familiar with this form of injury or gan-grene, serious injury, or death will result. CON-TACT A PHYSICIAN IMMEDIATELY IF FLUIDENTERS SKIN OR EYES. DO NOT DELAY.

Never allow children or untrained persons tooperate equipment.

PREPARATIONCheck that all hardware is properly installed.

Always tighten to torque chart specificationsunless instructed otherwise in this manual.

Air in hydraulic systems can cause erratic oper-ation and allows loads or equipment componentsto drop unexpectedly. When connecting equipmentor hoses or performing any hydraulic maintenance,purge any air in hydraulic system by operating allhydraulic functions several times. Do this beforeputt ing into service or al lowing anyone toapproach the equipment.

After connecting hoses, check that all controllever positions function as instructed in the Opera-tor's Manual. Do not put into service until controllever and equipment movements are correct.

Make sure all hydraulic hoses, fittings, andvalves are in good condition and not leaking beforestarting power unit or using equipment. Check androute hoses carefully to prevent damage. Hosesmust not be twisted, bent sharply, kinked, frayed,pinched, or come into contact with any movingparts. Operate moveable components through fulloperational range to check clearances. Replaceany damaged hoses immediately.

Protective hose sleeves must cover all hydrau-lic hoses within 20 inches of the operator and besecured onto metal hose fittings. Replace hoses orsleeves if damaged or if protective sleeve cannotbe properly positioned or secured.

Always wear relatively tight and belted clothingto avoid entanglement in moving parts. Wearsturdy, rough-soled work shoes and protectiveequipment for eyes, hair, hands, hearing, and head;and respirator or filter mask where appropriate.

Make sure attachment is properly secured,adjusted, and in good operating condition.

Safety is a primary concern in the design andmanufacture of our products. Unfortunately, ourefforts to provide safe equipment can be wipedout by an operator’s single careless act.

In addition to the design and configuration ofequipment, hazard control and accident preven-tion are dependent upon the awareness, con-cern, judgement, and proper training ofpersonnel involved in the operation, transport,maintenance, and storage of equipment.

It has been said, “The best safety device is aninformed, careful operator.” We ask you to bethat kind of operator.

SAFETY RULESATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Safety 71020 Loader SR (Rev. 2/16/2007)

Power unit must be equipped with ROPS orROPS cab and seat belt. Keep seat belt securelyfastened. Falling off power unit can result in deathfrom being run over or crushed. Keep foldableROPS system in “locked up” position at all times.

Make sure all safety decals are installed.Replace if damaged. (See Safety Decals section forlocation.)

Make sure shields and guards are properlyinstalled and in good condition. Replace if dam-aged.

To provide stability, add tractor manufacturer'srecommended wheel ballast or rear weight.

Move wheels to tractor manufacturer's widestrecommended setting to increase stability. Do notuse loader on tractors with single or double cen-tered front wheels.

To help prevent tractor/loader instability, neverexceed the capacity of the tractor/loader used withthe pallet fork. To increase stability, adjust tires tomaximum possible width.

Your dealer can supply original equipmenthydraulic accessories and repair parts. Substituteparts may not meet original equipment specifica-tions and may be dangerous.

OPERATION

Do not allow bystanders in the area when oper-ating, attaching, removing, assembling, or servic-ing equipment.

Improper use of a loader can cause injury ordeath.

Consult local utilities before working. Knowlocation of all underground cables, pipelines, over-head wires, and other hazards in working area andavoid contact.

The bale spear is to be used only for handlingbales. Do not use for digging rocks, pulling outfence, or as a craning device with a chain over thespear.

Do not attempt to lift loads in excess of theloader capacity.

Keep bystanders away from equipment.

Do not walk or work under a raised loader,bucket, or attachment.

Never allow anyone to get under the loaderbucket or reach through the lift arms when thebucket is raised.

Do not operate or transport equipment whileunder the influence of alcohol or drugs.

Operate only in daylight or good artificial light.

Always comply with all state and local lightingand marking requirements.

Never allow riders. Do not lift or carry anybodyon the loader or in the bucket or attachments.


Always sit in power unit seat when operatingcontrols or starting engine. Securely fasten seatbelt, place transmission in neutral, engage brake,and ensure all other controls are disengagedbefore starting power unit engine.

Look down and to the rear and make sure areais clear before operating in reverse.

Avoid loose fill, rocks, and holes. They can bedangerous for loader operation or movement.

Stop the loader arms gradually when loweringor lifting.

Use caution when handling loose or shiftableloads.

Allow for extra attachment length and widthwhen making turns.

The grapple fork is a clamping device andshould be used to clamp loose hay, straw, orsilage. It is not to be used to dig material loosefrom a pile.

AVOID INJURY OR DEATH FROM POWERLINES:

• Stay away from power lines.• Electrocution can occur without direct con-tact.• Check clearances before raising attachment.• Consult local utilities before digging. Knowlocation of and avoid contacting all under-ground cables, pipelines, overhead wires, andother hazards in digging area.• Do not leave the operator's seat if any part ofthe power unit or attachment contacts electriclines or underground cables.

(Safety Rules continued on next page)


(Rev. 9/17/20107)

8 Safety 1020 Loader SR (Rev. 2/16/2007)

(Safety Rules continued from previous page)

AVOID INJURY OR DEATH FROM ROLLOVERACCIDENTS:

• Move and turn tractor at less than 6 mph (10km/h).• Watch for hidden hazards such as holes,ditches, and other obstructions which maycause tractor and loader to tip over.• Carry loads close to the ground to aid visibil-ity and lower center of gravity for improved sta-bility.• Balance loads so weight is evenly distributedand load is stable.• Be extra careful when operating on a slope.• Do not operate on steep slopes.• Do not stop, start or change directions sud-denly on slopes.• If loader is equipped with round bale attach-ments, always approach bale with tractor facinguphill.• Be sure tractor tire spacing and rear ballast iscorrect before using loader.• Tractor must be equipped with a Roll-OverProtective Structure (ROPS) and seat belt. Keepseat belt securely fastened and keep foldableROPS systems in “locked up” position at alltimes.

AVOID INJURY OR DEATH FROM FALLINGBALES AND OTHER OBJECTS:

• Do not carry hay bales, logs, fence posts,stones, or any other loose objects that can roll,shift, or fall from a raised bucket and crushoperator or bystanders. • Do not handle round bales unless loader isequipped with approved bale handling attach-ment.• Handle raised loads with caution.• Carry loads low and drive slowly.

MAINTENANCE

Never work under a raised loader. Always lowerloader to the ground with bucket or loader attach-ment in full roll-back position. Shut off tractor, setparking brake, and remove key. Operate valvelevers to release any hydraulic pressure. If loaderobstructs tractor maintenance, loader must beremoved from tractor.

Do not modify or alter or permit anyone else tomodify or alter the equipment or any of its compo-nents in any way.

Your dealer can supply original equipmenthydraulic accessories and repair parts. Substituteparts may not meet original equipment specifica-tions and may be dangerous.

Always wear relatively tight and belted clothingto avoid entanglement in moving parts. Wearsturdy, rough-soled work shoes and protectiveequipment for eyes, hair, hands, hearing, and head;and respirator or filter mask where appropriate.

Keep all persons away from operator controlarea while performing adjustments, service, ormaintenance.

Tighten all bolts, nuts and screws to torquechart specifications. Check that all cotter pins areinstalled securely to ensure equipment is in a safecondition before putting unit into service.

Make sure all safety decals are installed.Replace if damaged. (See Safety Decals section forlocation.)

Make sure shields and guards are properlyinstalled and in good condition. Replace if dam-aged.

Do not disconnect hydraulic lines until all sys-tem pressure is relieved. Lower unit to ground,stop engine, and operate all hydraulic controllevers.

When servicing or replacing pins in cylinderends, buckets, etc., always use a brass drift andhammer. Failure to do so could result in injury fromflying metal fragments.

STORAGE

Block equipment securely for storage.

Stored loader can fall and cause serious injuryor death. Securely store loader and attachments toprevent falling.

To help prevent injury caused by a falling imple-ment, always detach on a hard level surface.

Secure equipment parking stand(s) in park posi-tion before detaching.

To provide necessary balance, loader framemust be equipped with bucket or attachmentbefore attaching or detaching from tractor, or whenloader is in stored position.

To help prevent personal injury from exposedfork tines, always store bale spear with tinespointed down, or against bale, building or otherstable object.


(Rev. 9/21/2007)

Safety 91020 Loader SR (Rev. 2/16/2007)

Do not loosen hydraulic fittings or hoses whileloader is in stored position.

Do not climb or lean on equipment stored onstand.

Keep children and bystanders away from stor-age area.



(Rev. 9/21/2007)

10 Safety MAN0553 (2/23/2007)

SAFETY & INSTRUCTIONAL DECALSATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

1 - PN 56053

56053-A

DANGER

ROLLOVERS CANRESULT IN INJURY

OR DEATH� Always use ROPS and

seat belt.� Add rear tractor

ballast.� Move wheels to widest

setting.� Avoid slope operation.� Operate at low speeds.� Carry load low.

Serious injury or deathcan result from contactwith electrical lines.

DANGER

��

� ��

� � � � �� !�"��#$�� %�&��#'

� �� !�� "�#

� �� !�� #

� (�� #

)��

��

2 - PN 56052

10 - SERIAL NUMBER PLATE

5 - PN 19924

��

� Check for leaks with cardboard; never use hand.� Before loosening fittings: lower load, release pressure, and

be sure oil is cool.� Consult physician immediately if skin penetration occurs.

WARNING

19924-B

WARNING� Read and understand Operator’s

Manual before operating.(Replacement manuals areavailable from dealer or, in theUnited States and Canada, call1-800-319-6637.)

� Keep others away when operatingloader.

� Do not allow children or untrainedpersons to operate equipment.

� Lower loader to ground, stop en-gine, set park brake and removekey before leaving tractor seat.

� Failure to follow safety rules canresult in serious injury or death.

56051-A

3 - PN 56051

(Rev. 8/1/2012)

Safety 11MAN0553 (2/23/2007)

56059-A

LOADER MOUNTING INSTRUCTIONSRead Operator’s Manual instructions before proceding.

To Remove Loader1. Park tractor on level surface with bucket flat on

ground.2. Dump bucket to take weight off mount pins and

allow for stand installation. Set brake and shut offtractor.

3. Remove stands from crosstube and pin into brackets.(Pin location noted in mounting manual.)

4. Remove mount pins from loader upright.5. Roll back bucket completely to raise uprights from

mounts.6. Shut off engine. Disconnect hydraulics. Back tractor

away. Store mount pins in loader uprights.

To Mount Loader1. Remove mount pins from uprights.2. Drive tractor into loader slowly.3. Shut off tractor. Connect hydraulics.4. Dump bucket to lower upright into mounts.5. Continue dumping bucket until uprights settle into

mounts, pins can be installed and stands can beremoved. Set brake and shut off tractor.

6. Install mount pins and clips. Remove stands and pininto crosstube.

8 - PN 560596 - PN 56050

LOADER ATTACHMENT CAN FALL OFF IF NOT PROPERLY ATTACHED.� Read operator’s manuals for instructions.� Position and align loader to attachment.� Rotate coupler handles to full locked position. Lockpins must fully extend and

engage into attachment retaining slots.� Attachment mechanism must be functional and in good repair.� Only use loader manufacturer approved attachments.� For information on approved attachments, call 1-800-319-6637.

Failure to follow these instructions can result in serious injury or death.

WARNING

56055-B

7 - PN 56055

BE CAREFUL!

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off.

Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

WARNING��

Only use loader manufacturer approved attachments.Failure to do so can cause serious injury or death. 45024-A

9 - PN 45024

4 - PN 1020371

SAFETY & INSTRUCTIONAL DECALSATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

12 Operation MAN0553 (2/23/2007)

OPERATION

Be familiar with and follow all safety rules and safetydecals in the manual, on the loader, and on the tractor.

The safe operation of this loader is the responsibility ofthe operator, who must be properly trained. The opera-tor should be familiar with the equipment and all safetypractices before starting operation. Read the safetyrules and safety decals on pages 6 through 11.

AVOID INJURY OR DEATH FROM POWERLINES:

• Stay away from power lines.• Electrocution can occur without direct con-tact.• Check clearances before raising attachment.• Consult local utilities before digging. Knowlocation of and avoid contacting all under-ground cables, pipelines, overhead wires, andother hazards in digging area.• Do not leave the operator's seat if any part ofthe power unit or attachment contacts electriclines or underground cables.




Never allow children or untrained persons tooperate equipment.

Keep bystanders away from equipment.


Keep hands and body away from pressurizedlines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety goggles.Hydraulic fluid under pressure can easily penetrateskin and will cause serious injury or death.


AVOID INJURY OR DEATH FROM FALLINGOBJECTS:

• Do not carry shiftable items. Hay bales, logs,fence posts, stones, and other objects can rollor fall from a raised attachment and crush oper-ator or bystanders. • This unit is not equipped with any method toprevent objects such as round bales, posts, orlogs from rolling back onto operator.• Do not handle round hay bales. • Carry loads low and drive slowly.• Do not carry large objects that can fall out ofattachment into operator zone.• Never lift load higher than necessary to clearthe ground when moving.

Always wear relatively tight and belted clothingto avoid getting caught in moving parts. Wearsturdy, rough-soled work shoes and protectiveequipment for eyes, hair, hands, hearing, and head;and respirator or filter mask where appropriate.

TRACTOR PREPARATION

Before operating the loader, extra weight should beadded to the rear of the tractor with rear wheel weightsor liquid ballast for optimum stability. Refer to your trac-tor operator's manual for weight information.

The tractor rear wheels should be moved to the tractormanufacturer's widest recommended settings toincrease the stability of the tractor.

For safety in preventing injury or death from rolloveraccidents, the tractor must be equipped with anapproved ROPS or ROPS cab and seat belt.

Pin-on bucket must be securely attached to the loaderusing pins and retaining hardware supplied with thebucket.

��

��

��

CAUTION

Operation 13MAN0553 (2/23/2007)

CONNECT BUCKET OR ATTACHMENTUSING QUICK ATTACH COUPLER

Position the hydraulic hoses so they will not be pinchedwhen connecting the attachment.

The quick attach coupler handles should be in theunlocked position with lock pins retracted, Figure 1.

Figure 1. Quick Attach Coupler Handles - Unlocked

Move to the operator seat, fasten seat belt, and startengine.

Lower loader lift arms to their lowest position.

Carefully move and align the quick attach coupler tothe bucket or attachment. The top of the quick attachcoupler must index into the attachment or bucketflange, Figure 2.

Roll the attachment coupler into the attachment flangeso the coupler handles can be engaged.

Figure 2. Connecting Bucket or Attachment to Loader

Shut off the engine, set brake, remove key, and removeseat belt. Dismount the tractor.

Move the attachment coupler handles to the lockedposition. The lockpins must be completely extendedand secured into the retaining slots provided on theattachment, Figure 3 and Figure 4.

Attachment coupler handles must always berotated to LOCK POSITION to prevent coupler latchfrom disengaging and attachment from falling off.

Connect hydraulic hoses to loader auxiliary quick cou-plers (optional).

Figure 3. Attachment Coupler Handles - Locked

Figure 4. Retaining Slot Locations - Back View of Attachment

LOADER OPERATION


The loader should be operated with the tractor enginerunning at a safe RPM. Excessive speeds are danger-ous, and may cause bucket spillage and unnecessarystrain on the tractor and loader.

��

��

14 Operation MAN0553 (2/23/2007)

Filling Bucket

1. Approach and enter the pile with a level bucket.

Figure 5. Filling Bucket

2. Loaders with single handle controls: Ease thelever back and toward you to lift and roll back thebucket, Figure 6.

Figure 6. Single Handle Control

3. Lift and rollback bucket.

Figure 7. Lift and Rollback Bucket

The lift and rollback of the bucket will increase effi-ciency because maintaining a level bucket throughoutthe lifting cycle resists bucket lift and increases break-away effort, Figure 7.

NOTE: Do not be concerned if the bucket is not com-pletely filled during each pass. Maximum productivity isdetermined by the amount of material loaded in a givenperiod of time. Time is lost if two or more attempts aremade to fill the bucket on each pass.

Lifting Load

Do not attempt to lift loads in excess of theloader capacity.

When lifting the load, keep the bucket positioned toavoid spillage, Figure 8.

Figure 8. Lifting Load

Carrying Load

Position the bucket just below the level of the tractorhood for maximum stability and visibility, whether thebucket is loaded or empty, Figure 9..

Figure 9. Carrying Load

Operating on a Slope


• Move and turn tractor at less than 6 mph (10km/h).• Watch for hidden hazards such as holes,ditches, and other obstructions which maycause tractor and loader to tip over.• Carry loads close to the ground to aid visibil-ity and lower center of gravity for improved sta-bility.• Balance loads so weight is evenly distributed

��

��

Operation 15MAN0553 (2/23/2007)

and load is stable.• Be extra careful when operating on a slope.• Do not operate on steep slopes.• Do not stop, start or change directions sud-denly on slopes.• If loader is equipped with round bale attach-ments, always approach bale with tractor facinguphill.• Be sure tractor tire spacing and rear ballast iscorrect before using loader.• Tractor must be equipped with a Roll-OverProtective Structure (ROPS) and seat belt. Keepseat belt securely fastened and keep foldableROPS systems in “locked up” position at alltimes.

Use extreme care when operating the loader on aslope, keeping the bucket as low as possible. This willmaintain a low center of gravity for the bucket and trac-tor and will provide maximum tractor stability.

When transporting the load, keep the bucket as low aspossible to avoid tipping in case a wheel drops in a rut.

Figure 10. Operating on a Slope

Dumping Bucket

Figure 11. Dumping Bucket

Lift the bucket high enough to clear the side of the vehi-cle. Move the tractor in as close as possible, thendump the bucket. See Figure 11.

Lowering BucketAfter the bucket is dumped, back away from the vehiclewhile lowering and rolling back the bucket.

Figure 12. Control Handle Function

Operating with Float ControlDuring hard surface operation, keep the bucket leveland put the lift control in the float position to permit thebucket to float on the working surface. If hydraulicdown pressure is exerted on the bucket, it will wearfaster than normal.

The float will also prevent the mixing of surface mate-rial with stockpile material. The float position willreduce the chance of surface gouging when removingsnow or other material.

Figure 13. Float Position

1- LeverControl

16 Operation MAN0553 (2/23/2007)

Loading from a Bank

See Figure 14.

Exercise caution when undercutting high banks. Dirtslides can be dangerous. Load the bucket from as lowa position as possible for maximum efficiency. Loaderlift and break-away capacity diminish as loading heightis increased.

Keep the bucket level when approaching a bank orpile. This will help prevent gouging in the work area.

Figure 14. Loading from a Bank

Peeling and Scraping

Use a slight bucket angle, travel forward, and hold thelift control forward to start the cut. Make a short 5-inchto 8-inch angle cut and break-out cleanly, Figure 15.

With the bucket level, start a cut at the notch approxi-mately 2 inches deep. Hold the depth by feathering thebucket control to adjust the cutting lip up or down.When the front tires enter the notch, adjust the lift cylin-der to maintain proper depth, Figure 16.

Figure 15. Angle Cut

Figure 16. Peeling/Scraping

Make additional passes until the desired depth isreached. During each pass, only use the bucket control

while at working depth. This will allow you to concen-trate on controlling the bucket angle to maintain a pre-cise cut, Figure 17.

Figure 17. Additional Passes

Loading Low Trucks or Spreaders from a Pile

For easier loading, minimize the angle of turn andlength of run between pile and spreader, Figure 18.

Figure 18. Loading

Backgrade occasionally with a loaded bucket to keepthe working surface free of ruts and holes. Also, holdthe lift control forward so the full weight of the bucket isscraping the ground. Use the heel of the bucket.

Figure 19. Backgrading

Backblading

Position the bucket at an angle of less than 45 degreesand back up slowly, Figure 20.

Backgrading with the bucket tilted too far will result indamage to bucket cylinders and void warranty, Figure21.

Operation 17MAN0553 (2/23/2007)

Figure 20. Backblading

Figure 21. Bucket Tilted too Far

Backfilling

1. Approach the pile with a flat bucket, Figure 22.

Figure 22. Backfilling Correctly

2. Do not use the bucket in the dump position forbulldozing. This method will impose severe shockloadings on the dump linkage, the bucket cylinder,and the tractor, Figure 23.

Figure 23. Incorrect Bucket Position for Backfilling

3. Leave dirt in the bucket because dumping on eachpass wastes time.

4. Operate at right angles to the ditch. Take as big abite as the tractor can handle without luggingdown.

5. Leave dirt that drifts over the side of the bucket forfinal clean-up.

6. Pile dirt on the high side for easier backfilling on aslope.

HANDLING OBJECTS



Figure 24. Avoid Falling Loads

FORKLIFT OPERATION

To avoid injury or death from bale rolling backdown loader, do not handle round bales with thepallet fork.

To help prevent tractor/loader instability, neverexceed the capacity of the tractor/loader used withthe pallet fork. To increase stability, adjust tires tomaximum possible width.

Use the pallet fork to move pallets, bulk bins, crates,boxes and hampers.

Do not use for shiftable loads such as logs or poles.Do not use for digging rocks or lifting concrete slabs.

��

��

CAUTION

18 Operation MAN0553 (2/23/2007)

BALE SPEAR OPERATION




Stop the loader arms gradually when loweringor lifting.



To help prevent personal injury from exposedfork tines, always store bale spear with tinespointed down, or against bale, building or otherstable object.

The bale spear is to be used only for handling roundbales. Do not use for digging rocks, pulling out fence,or as a craning device with a chain over the spear.

Picking Up a Round Bale with Bale Spear

Approach bale with spike level and centered on bale.Push spike into bale until bale is against the frame.Raise and roll bale back just high enough to provideground clearance for transport, Figure 25.

Figure 25. Picking Up a Round Bale

Picking Up Round Bale on a Slope with Bale SpearTo help prevent injury caused by tractor rollover whenhandling round bales on a slope, avoid side slopetravel whenever possible. Drive up slope to pick upbale and back down in reverse. Transport bale as closeto the ground as possible.

Approach bale with tractor facing uphill, spike level andcentered on bale. Push spike into bale until bale isagainst the frame. Raise and roll bale back just highenough to provide ground clearance for transport.Select low tractor speed before moving or turning on aslope, Figure 26.

Figure 26. Picking Up Round Bale on a Slope

Transporting a Round BaleTo help prevent personal injury or accident causedfrom a bale falling off the spike, carry the bale low andslightly rolled back. Travel slowly over rough ground.

Figure 27. Transporting a Round Bale

��

CAUTION

Operation 19MAN0553 (2/23/2007)

GRAPPLE OPERATION

The grapple fork is a clamping device and should beused to clamp loose hay, straw, or silage. It is not to beused to dig material loose from a pile.


• Move and turn tractor at less than 6 mph (10km/h).• Watch for hidden hazards such as holes,ditches, and other obstructions which maycause tractor and loader to tip over.• Carry loads close to the ground to aid visibil-ity and lower center of gravity for improved sta-bility.• Balance loads so weight is evenly distributedand load is stable.• Be extra careful when operating on a slope.• Do not operate on steep slopes.• Do not stop, start or change directions sud-denly on slopes.• If loader is equipped with round bale attach-ments, always approach bale with tractor facinguphill.• Be sure tractor tire spacing and rear ballast iscorrect before using loader.• Tractor must be equipped with a Roll-OverProtective Structure (ROPS) and seat belt. Keepseat belt securely fastened and keep foldableROPS systems in “locked up” position at alltimes.



Use caution when handling loose or shiftableloads.

Never handle large, heavy objects due to the dangersof rolling the tractor over, upending the tractor, andhaving the object roll or slide down the loader armsonto the operator.

Never lift loader higher than necessary to clear theground. When necessary, ballast the tractor rear tocompensate for load. Never lift large objects. Moveslowly and carefully. Avoid rough terrain. Stop theloader gradually when lowering or lifting loads.

For loose hay or other materials, adjust the mountingarms and the grapple teeth in the position that providesthe best performance.

Set the rear tractor wheels to the widest recommendedsetting. Add enough ballast at the rear end so at least50% of the original rear wheel weight is maintainedwhen the load in the loader is at transport height.

Always carry the load on level ground or directly uphill.Never move along a side hill or directly downhill when aload is carried.

Make sure the grapple is holding the load securely so itcannot roll backwards or sideways.

Removing Hay & Silage from a Pile with Grapple Fork

The grapple fork is a clamping device andshould be used to clamp loose hay, straw, orsilage. It is not to be used to dig material loosefrom a pile.

If possible, remove material from the top of the pilefirst. Use the loader bucket to break material loose.Equip the bucket with teeth for better loosening actionin packed silage. After material is loosened, close grap-ple, Figure 28.

Figure 28. Removing Hay and Silage from a Pile with a Grapple Fork

��

��

20 Operation MAN0553 (2/23/2007)

Dumping into Truck, Wagon & SpreadersUse extreme care when dumping into trucks, wagons,spreaders, etc. when grapple is attached to bucket.

Open grapple teeth will swing a wide radius beyondbucket and can damage or puncture the opposite sidesof these implements, out of the operator's sight.

CLEANING

After Each Use● Remove large debris such as clumps of dirt, grass,

crop residue, etc. from machine.

● Inspect machine and replace worn or damagedparts.

● Replace any safety decals that are missing or notreadable.

Periodically or Before Extended Storage● Clean large debris such as clumps of dirt, grass,

crop residue, etc. from machine.

● Remove the remainder using a low-pressure waterspray.

1. Be careful when spraying near scratched or tornsafety decals or near edges of decals as waterspray can peel decal off surface.

2. Be careful when spraying near chipped orscratched paint as water spray can lift paint.

3. If a pressure washer is used, follow the adviceof the pressure washer manufacturer.

● Inspect machine and replace worn or damagedparts.

● Sand down scratches and the edges of areas ofmissing paint and coat with Woods spray paint of

matching color (purchase from your Woodsdealer).

● Replace any safety decals that are missing or notreadable (supplied free by your Woods dealer).See Safety Decals section for location drawing.

PRE-OPERATION CHECK LIST (OWNER'S RESPONSIBILITY)

___ Review and follow all safety rules and safetydecal instructions on pages 6 through 11.

___ Check that all safety decals are installed and ingood condition. Replace if damaged.

___ Check that all hardware and cotter pins are prop-erly installed and secured.

___ Check that equipment is properly and securelyattached to tractor.

___ Do not allow riders.

___ Check all lubrication points and grease asinstructed in Owner Service, "Lubrication", page21.

___ Check that all hydraulic hoses and fittings are ingood condition and not leaking before startingtractor. Check that hoses are not twisted, bentsharply, kinked, frayed or pulled tight. Replaceany damaged hoses immediately.

___ Make sure tractor ROPS or ROPS cab and seatbelt are in good condition. Keep seat beltsecurely fastened during operation.

___ Before starting engine, operator must be in trac-tor seat with seat belt fastened. Place transmis-sion in neutral or park, engage brake, anddisengage tractor PTO.

MAN0553 (2/23/2007) Owner Service 21

OWNER SERVICEThe information in this section is written for operatorswho possess basic mechanical skills. If you need help,your dealer has trained service technicians available.For your protection, read and follow the safety informa-tion in this manual.






Before dismounting power unit or performingany service or maintenance, follow these steps:disengage power to equipment, lower the 3-pointhitch and all raised components to the ground,operate valve levers to release any hydraulic pres-sure, set parking brake, stop engine, remove key,and unfasten seat belt.

If you do not understand any part of this manualand need assistance, see your dealer.


Lubrication

NOTICE■ When adding oil to the tractor reservoir, alwaysuse hydraulic oil as specified by the tractor manu-facturer.

Daily

___ Check the level of hydraulic oil in tractor beforestarting each day's operation. If necessary, addoil as recommended in your tractor owner's man-ual.

___ Lubricate after every eight hours of operation;lubricate pivot pins at each end of each lift boomarm and at rod and base end of each boom andbucket cylinder.

___ After every eight hours of operation, check allhardware and tighten where required.

___ Replace hoses immediately if they are damagedby a cut or scrape, extruded at the fittings, orleaking. Hydraulic oil leaks should be repairedpromptly to avoid loss of oil and serious personalinjury from escaping oil.

100 Hours

___ Lubricate attachment coupler pivots and linkagewith light oil and inspect for damaged or missingcomponents.

Annually

___ Lubricate direct mount joystick linkage withgrease.

Figure 30. Lubricate Pivot Pins

��

CAUTION

22 Owner Service MAN0553 (2/23/2007)

Pivot Bearing LubricationNOTE: Pivot bearings are located between:

• Loader upright and boom (A)• Loader boom and bucket (D)

Figure 31. Pivot Bearing Locations

These areas are greased at the factory and should pro-vide acceptable service without regreasing the bearingsurface for several years. If excessive play or noise isdetected, adding grease to bearing may be necessary.

Apply grease to bearings as follows:

1. Remove loader from tractor.

2. Remove pivot pin from pivot point.

NOTE: Make sure to support upright and/or lift cyl-inders to prevent them from falling while the loaderis being disassembled.

3. Apply grease to both bearings. Allow grease to fillsmall cavities in bearing.

4. Reassemble pivot point and secure pin with bolt.

5. Repeat process for each pivot point.

Figure 32. Replaceable Bearings (Typical)

DP7

Add Greaseto bearings

Troubleshooting 23MAN0553 (2/23/2007)

TROUBLESHOOTINGThe following is a list of service problems, possible causes, and solutions. If problems still exist after preforming thesolution, contact your nearest Woods dealer for authorized service.

(Continued on next page)

PROBLEM POSSIBLE CAUSE SOLUTION

Jerky operation Air in hydraulic system Cycle cylinders several times to purge system of air.

Cold hydraulic oil Run engine to warm oil.

Low hydraulic oil level Add oil to level specified.

Poor oil circulation Change oil filter and clean screen in tractor hydraulic system.

Worn or damaged hydraulic pump Repair or replace pump.

Air leak in pump inlet line Check, tighten or replace inlet line.

Slow operation Faulty valve Repair or replace valve.

Air in hydraulic system Cycle lift cylinders and bucket cylinders several times to free system of air.

Hydraulic oil too heavy Change to proper oil.

Oil filter plugged Clean and replace filter.

Slow engine speed Increase engine speed rate.

Cylinder piston seals leaking Install seal repair kit.

Remote valve incorrectly adjusted or malfunctioning

Adjust, repair, or replace control valve.

Tractor hydraulic pump malfunction-ing

Repair or replace pump.

Hydraulic pump too small; hoses or feedlines restricted

Check hoses and feed lines for kinks and other restrictions.

Hydraulic couplers not completely engaged

Connect hydraulic couplers.

Oil leaks Loose hose connections Tighten fittings. Use thread sealer on pipe (tapered) threads.

Fittings or hoses defective Replace defective parts.

Hydraulic cylinder seals worn or damaged

Install seal repair kit.

Remote valve components worn or damaged

Repair and/or replace.

24 Troubleshooting MAN0553 (2/23/2007)

TROUBLESHOOTING(Continued from previous page)

Cannot raise load Low oil supply Check oil level.

Bucket overloaded Try lighter load.

Hydraulic couplers not fully engaged

Reconnect hoses.

Cylinder piston seal leakage Install seal repair kit.

Control valve incorrectly adjusted or malfunctioning

Repair or replace control valve.

Tractor valve not open to provide circuit to auxiliary valve

Open tractor valve. Be sure pres-sure is to inlet side of auxiliary valve.

Hydraulic pump malfunctioning Repair or replace hydraulic pump.

Load is greater than boom lift capacity

Check loader specifications.

Bucket or boom leaks down from “hold” position

Leaks in hydraulic circuits Tighten loose fittings. Use thread sealer on pipe (tapered) threads.

Cylinder piston seals leaking Install seal repair kit.

Control valve worn or damaged Repair or replace control valve.

Tractor valve worn or damaged Repair or replace tractor valve.

Cannot lower boom Hydraulic couplers not fully engaged

Recouple hoses.

Loss of bucket tilt control when lever is pushed completely for-ward

Tractor lever in “float” position Use float lockout control to pre-vent lever from being moved to “float” position.

Couplers hard to hook up Pressure in circuit Place control levers in “float” when connecting.

Boom and bucket operation does not correspond to control lever position

Improperly connected hydraulic couplers

Connect hydraulic couplers cor-rectly. See Hydraulic Kit Manual for proper connections.

Hoses improperly connected Connect hoses properly. See Hydraulic Kit Manual for proper connections.

Excessive wear on bucket cutting edge and wear pads

Bucket is tilted too far forward and is riding on cutting edge

Keep bottom of bucket parallel to ground. Use rod gauge to indicate level bucket position.

Excessive down pressure when cleaning feedlots and working on concrete

Use “float” position on boom lift control lever.

MAN0553 (2/23/2007) Dealer Service 25

DEALER SERVICEThe information in this section is written for dealer ser-vice personnel. The repair described herein requiresspecial skills and tools. If your shop is not properlyequipped or your mechanics are not properly trained inthis type of repair, you may be time and money aheadto replace complete assemblies.


Never allow anyone to get under the loaderbucket or reach through the lift arms when thebucket is raised.






CYLINDER SERVICEThe cylinders are designed to be reliable and easy toservice. If a cylinder should malfunction during the war-ranty period, return the complete cylinder assembly,without disassembling, to your authorized servicedepartment or contact your authorized service depart-ment for instructions. Unauthorized disassembly of acylinder in the warranty period will VOID WARRANTY.

NOTE: Repair to cylinders is limited to replacing seals,wear rings, and O-rings. Replacing rod, barrel, or pis-tons is not cost effective. Purchasing a complete cylin-der is more economical.

The loader was assembled with either a spanner nutassembly or threaded rod guide assembly. See Figure33 and Figure 34 to determine the style of cylinder onyour loader. Spanner nut cylinders can also have infor-mation stamped on the barrel near the base end port.Check the repair parts section of the manual for moreinformation. Follow repair procedures for each style ofcylinder.

Figure 33. Spanner Nut Cylinder

Figure 34. Threaded Rod Gland Cylinder

��

CAUTION

DP1

SpannerNut

ThreadedRod Gland

DP2

(Rev. 8/1/2012)

26 Dealer Service MAN0553 (2/23/2007)

CYLINDER REPAIR

Spanner Nut Cylinders

Disassembly

Figure 35. Spanner Nut Cylinder Assembly

On spanner nut style cylinders, unscrew spanner nut(4) using a spanner wrench, or carefully use a punchand hammer.

Tap rod guide (5) into barrel (8) about 1/2". Removeround retaining ring (3B). Pull on rod (1) to removeparts from barrel.

Clamp cross pin end of rod assembly (1) in a vise withprotective jaws. Remove lock nut (7) from rod assem-

bly. Remove piston (6), stop tube (2) if equipped, androd guide (5) from rod.

Remove and discard all seals, wear rings and O-rings.Clean all components in solvent and blow dry with lowpressure air.

Inspect inside diameter of barrel (8). Replace cylinder ifdamaged.

Assembly

Lubricate O-rings and seals with clean hydraulic fluid.Install back-up washer (3E) on rod guide (5), theninstall O-ring (3F) in exterior O-ring groove of rodguide. Install rod seal (3D) into inner groove of rodguide with open portion of V-groove toward piston.

Place rod wiper (3C) in outer rod guide groove. Sliderod guide assembly (5) onto rod (1). Place crown pis-ton seal (3G) in piston groove.

Lightly coat rod threads with hydraulic oil and slide O-ring (3A) over threads and into groove. Install stop tube(if equipped) and piston (6) onto rod (1) as shown inFigure 36. Completely clean threads of hydraulic oil,apply Locquic® Primer 7649 and Loctite® 242 to therod threads, and install lock nut (7). Torque to 175 lbs-ft.

Compress crown piston seal and carefully insert pistonand rod assembly into barrel. Use care to prevent dam-age while installing.

Carefully push or tap rod guide (5) into barrel (8) justpast groove inside barrel. Insert retaining ring (3B) intogroove and pull rod (1) to seat rod guide (5) againstring. Apply Loctite 242 to rod guide threads. Screwspanner nut (4) into rod guide (5) using a spannerwrench, or carefully use a punch and hammer.

Figure 36. Spanner Nut Cylinder Assembly

1. Piston rod2. Stop tube

(not on all cylinders)3A. O-Ring 3B. Retaining ring3C. Wiper ring3D. Rod seal3E. Back-up ring3F. O-Ring3G. Crown piston seal

4. Spanner nut5. Rod guide assembly6. Piston7. Lock nut8. Cylinder barrel

(Rev. 8/1/2012)


Threaded Rod Guide Cylinders

Figure 37. Threaded Rod Guide Cylinder Assembly

Disassembly

On threaded guide type cylinders, unscrew guide (5)using a spanner wrench, or carefully use a punch andhammer. (Spanner wrench 1021841 is available fromWoods to help with these procedures.) Pull on rod (1)to remove parts from barrel.

Clamp cross pin end of rod assembly (1) in a vise withprotective jaws. Unscrew piston (6) from end of rodassembly using a spanner wrench, or carefully use apunch and hammer. Remove rod guide (5) from rod.


Inspect inside diameter of barrel. Replace cylinder ifdamaged.

Assembly

For these assembly instructions the front surface of thethreaded rod guide with two holes or grooves will bereferred to as the "rod guide face".

Lubricate O-rings and seals with clean hydraulic fluid.Install back-up washer (3D) on rod guide (5), and theninstall O-ring (3E) in exterior O-ring groove of rodguide. See Figure 38. Make sure that the back-up ringis located closest to the rod guide face. Place rod wiper(3B) in outer rod guide groove. Install rod seal (3C) intothe second groove from the rod guide face with theopen portion of V-groove toward piston.

With all of the rod guide seals installed, slide the rodguide assembly (5) onto rod (1).

Install crown piston seal (3J) onto piston (6). Install off-set rings (3H) on both sides of the crown piston seal(3J) in the large groove on the piston (6). The profile ofthe offset ring (3H) should mate with the lip on thecrown piston seal (3J). Place the “L” shaped guide ring(3G) on the outside of each offset ring (3H).

Lightly coat rod threads with hydraulic oil and slide O-ring (3A) over threads and into groove. Completelyclean threads of hydraulic oil, apply Locquic Primer7649 and Loctite 242 to the rod threads, and threadpiston (6) onto rod (1) with the two holes in the pistonorientated away from the rod. Torque the piston (6) to100 lbs-ft.

Compress wear rings and piston seals and carefullyinsert piston and rod assembly into barrel. Use care toprevent damage while installing. Carefully screw rodguide (5) into barrel (8) using a spanner wrench, orcarefully use a punch and hammer.

Figure 38. Cylinder Assembly (No Letter Stamped)

DP8A 1

5

6

1. Piston rod3A. O-Ring 3B. Wiper ring3C. Rod seal3D. Back-up ring3E. O-Ring3G. Guard ring3H. Offset ring3J. Crown piston seal5. Rod guide assembly6. Piston8. Cylinder barrel

(Rev. 8/1/2012)

28 Dealer Service MAN0553 (2/23/2007)

Type “E” Threaded Rod Guide

Disassembly (Figure 39)

On threaded guide type cylinders, Figure 39, removeset screw (4), unscrew guide (5) using a spannerwrench, or carefully use a punch and hammer. Pull onrod (1) to remove parts from barrel.

Clamp cross pin end of rod assembly (1) in a vise withprotective jaws. Remove locknut (7) from rod assem-bly. Remove piston (6) and rod guide (5) from rod.


Inspect inside diameter of barrel (8). Replace cylinder ifdamaged.

Assembly (Figure 39)

Lubricate O-rings and seals with clean hydraulic fluid.Install back-up washer (3D) on rod guide (5), theninstall O-ring (3E) in exterior O-ring groove of rodguide. Install rod seal (3C) into inner groove of rodguide with open portion of V-groove toward piston.

Place rod wiper (3B) in outer rod guide groove. Sliderod guide assembly (5) onto rod (1). Place piston seal(3F) in piston groove.

Lightly coat rod threads with hydraulic oil and slide O-ring (3A) over threads and into groove. Install piston (6)onto rod (1) with ear ring on side away from rod guide.Install locknut (7) and torque to 175 lbs-ft.

Compress piston seal and carefully insert piston androd assembly into barrel. Use care to prevent damagewhile installing.

Carefully screw rod guide (5) into barrel (8) using aspanner wrench, or carefully use a punch and hammer.Screw set screw (4) into rod guide (5).

Figure 39. Threaded Guide Cylinder Assembly

1. Piston rod3A. O-Ring3B. Wiper ring3C. Rod seal3D. Back-up washer3E. O-Ring3F. Piston ring3G. Piston wear ring (Not

used)

4. Set screw5. Rod guide assembly6. Piston7. Locknut8. Cylinder barrel

(Rev. 8/1/2012)


PIVOT BEARING REPLACEMENT

Figure 40. Bearing Locations

Two replaceable bearings per pivot joint are located in:

• Boom pivot (A)

• Loader boom bucket pivot (D)

Bearing repair kits for LC102 loader are:

1025297 8 Bearing repair kit complete(All pivot points)

1006113 2 Bearing repair kit 1.00” pins(for any 1” pivot points)

Figure 41. Replaceable Bearings (Typical)

DP7

30 Assembly MAN0553 (2/3/2007)

ASSEMBLY

DEALER SET-UP INSTRUCTIONS

Loader assembly is the responsibility of the Woodsdealer. The loader is shipped assembled on a pallet foryour convenience. The loader must be properly set upand installed to assure prolonged service life and safeoperation.





Do not modify or alter or permit anyone else tomodify or alter the equipment or any of its compo-nents in any way.


ASSEMBLY INSTRUCTIONS

Loader Mounting Kit and Hydraulic Kit Installation

Install the loader mounting kit on the tractor accordingto specific mounting instructions included with themounting kit and hydraulic kits.

Loader Set-Up

Make sure all hydraulic hoses, fittings, andvalves are in good condition and not leaking beforestarting power unit or using equipment. Check androute hoses carefully to prevent damage. Hosesmust not be twisted, bent sharply, kinked, frayed,pinched, or come into contact with any movingparts. Operate moveable components through fulloperational range to check clearances. Replaceany damaged hoses immediately.

■ Lift and support all loader components safely.

■ Stand clear of the loader while attaching. Theloader could fall, causing serious personal injury.Always work safely and think clearly!

Remove bucket and attachment coupler from shippingskid. Remove manual tube from its shipping location,save for later installation. Remove plastic caps fromholes in loader.

Support loader frame and remove lag screws fromplates that hold frame on skid. Lower frame to ground.

Using an overhead lifting devise, lift loader frame andposition tractor so uprights can be placed into mountingshoes. Secure uprights into mounts with pin shippedwith frame. Cut shipping straps around boom cylindersand remove spacer angle and protective sleeves.

Refer to Hydraulic Hose Installation in the loadermounting kit. Always use hoses that have a minimumworking pressure rating of 3000 psi and meet orexceed SAE 100R1 specifications.

Refer to Control Valve Manual for optional control valveinstructions.

Connect loader hoses and start tractor. Clear hydraulicsystem of air by raising and lowering boom frame andactuating bucket cylinders several times. After air hasbeen purged from system, with loader boom onground, check the tractor hydraulic oil level as shown intractor owner's manual. When adding oil to hydraulicsystem, always use the type of oil specified for the trac-tor. NEVER MIX OIL TYPES.

A��WARNING

A��CAUTION

A��WARNING

MAN0553 (2/23/2007) Assembly 31

Manual Tube Installation1. Remove feedline cover (5) from cross tube by

removing lock nuts (29) and flat washers (21).

2. Attach manual tube (2) to the feedline cover usingtwo cap screws (28) and lock nuts (32). See Figure42.

3. Replace feedline cover using hardware previouslyremoved.

Figure 42. Manual Tube Installation

Pin-On Bucket Installation

Figure 43. Pin-On Bucket InstalledCylinder & Right Boom Shown

NOTE: Make sure replaceable bearings in loaderboom are coated with grease. Apply grease if neces-sary, allow grease to fill small cavities in bearings.

1. Remove loader pins and bucket pins from thebucket mounting lugs.

2. Attach lower holes on bucket to loader boom usingpins and hardware provided.

3. Extend bucket cylinder and attach it to the lugs onthe center of the bucket using pins and hardwareprovided.

Quick Attach Coupler Installation

NOTE: Make sure replaceable bearings in loaderboom are coated with grease. Apply grease if neces-sary, allow grease to fill small cavities in bearings.

1. Remove attachment coupler from bucket.

2. Position quick attach coupler on the ground in frontof the loader frame.

3. Attach quick attach coupler (lower holes) to end ofloader boom using pins and retaining hardwarethat came with the quick attach coupler, Figure 44.

4. Extend bucket cylinder and attach it to the lugs onthe center of the quick coupler using pins andhardware provided.

NOTE: To ease installation, plugs in hydraulicfeedlines may need to be removed.

Figure 44. Quick Attach Coupler Installed

2. Manual tube5. Feedline cover

21. 5/16 Flat washer28. 5/16 NC x 3/4 HHCS GR529. 5/16 NC Lock nut32. 5/16 NC Flange lock nut

DP3

32 Assembly MAN0553 (2/3/2007)

Bucket Connection to Quick Attach CouplerSee connect bucket or attachment using Quick AttachCoupler, page 13 to connect bucket.

Bucket Level Indicator Installation

Figure 45. Install Level Indicator - (Typical)

1. Remove bucket level indicator rod from its shippingposition on right loader boom leg.

2. Slide rod through bucket level indicator bracket onright boom frame.

3. Pin on Bucket: Attach opposite end of rod to holeinside ear of bucket. Secure rod with two cotterpins and washers.

3. Quick Coupler: Attach opposite end of rod to tabprotruding from rear of the quick attach coupler.Secure rod with two cotter pins and washers.

Bucket Level Indicator Adjustment

With tractor and loader on flat surface, adjust boomand bucket cylinders as necessary and place bottomsurface of bucket level on the ground.

Shut off tractor, set park brake, remove key and exitthe tractor.

Loosen hex nut and slide indicator bracket (2) so thatbend in indicator rod (1) is centered in the bracket.Tighten hex nut. See Figure 45.

Grease Loader

Lubricate all pivot points shown on page 21 with a highquality SAE multi-purpose grease. The attachmentcoupler handle pivots should be lubricated with a lightpenetrating oil.

Parking Stand Installation

Follow Loader Removal instructions on page 34.

If necessary, shorten parking stand enough to preventinterference.

2

1

MAN0553 (2/23/2007) Dealer Check Lists 33

DEALER CHECK LISTS

PRE-DELIVERY CHECK LIST(Dealer's Responsibility)

Inspect the loader thoroughly after assembly to be cer-tain it is set up properly before delivering it to the cus-tomer. The check lists are a reminder of points toinspect. Check off each item as it is found satisfactoryor after proper adjustments are made.

___ Check all bolts to be sure they are properlytorqued.

___ Check and grease all lubrication points. See“Lubrication” on page 21.

___ Check that shields and guards are properlyinstalled and in good condition. Replace if dam-aged.

___ Check that all cotter pins and safety pins areproperly installed. Replace if damaged.

___ Properly attach implement to tractor and make allnecessary adjustments.

___ Check all hydraulic hoses, fittings, tubing, andcylinders for any leaks or damage. Be sure quickcouplers operate properly. Make sure hydraulicvalve matches tractor hydraulic system - opensystem or closed system.

___ Check parking stand for proper operation.

___ Check that all safety decals are installed and ingood condition. Replace if damaged.

___ Check that all loader mounting decals are prop-erly installed on left loader mount.

___ Make sure all hydraulic fittings are tight andhoses are properly routed and not twisted, bentsharply, kinked or pulled tight.

___ Make sure loader operates as recommended.See operation section. Make necessary changesin hydraulic hook-ups to obtain loader operation.Cycle loader (all functions). Bleed air fromhydraulic system. Cycling loader removes airfrom system. After cycling loader, check hydraulicsystem oil level.

DELIVERY CHECK LIST(Dealer's Responsibility)

___ Present Operator's Manual and request that cus-tomer and all operators read it before operatingequipment. Point out the manual safety rules,explain their meanings and emphasize theincreased safety hazards that exist when safetyrules are not followed.

___ Show customer how to make adjustments.

___ Instruct customer how to lubricate and explainimportance of lubrication.

___ Explain to customer the potential crushing haz-ards of going underneath raised equipment.Instruct customer that service work does notrequire going underneath unit and never to do so.

___ Show customer the safe, proper procedures to beused when mounting, dismounting, and storingequipment.

___ Point out the correct mounting and routing ofhydraulic hoses. Explain that during operation,mounting, dismounting and storage, care must betaken to prevent hose damage from pulling, twist-ing and kinking.

___ Make customer aware of optional equipmentavailable so that customer can make properchoices as required.

A Delivery Report and Registration form must be filledin by dealer and signed by both dealer and purchaserat time of delivery. Be sure Operator's Manual remainswith loader. Deliver it to customer with loader.

34 Installation MAN0554 (Rev. 2/16/2007)

INSTALLATION

ATTACH LOADER TO TRACTOR

Remove mount pins from loader uprights.

Align tractor with loader and drive tractor into loaderslowly.

Figure 46. Align Tractor to Loader (Typical)

Shut off tractor. Connect the hydraulic hoses.

Drive tractor forward and dump bucket to lower uprightinto mounts.

Continue dumping bucket until uprights settle intomounts and mounting pin holes are aligned. Set brakeand shut off the tractor. Install mount pins and retainingclips.

Figure 47. Loader Attached to Tractor (Typical)

Remove stands from loader arms and place in loadercrosstube for storage. Pin in storage position using hairpins provided (Figure 48).

Return bent pins to brackets on crosstube and securewith safety pins provided.

Figure 48. Stands Stored in Crosstube

REMOVE LOADER FROM TRACTOR

Bucket must be installed to remove loader.

Park tractor on a level surface and lower bucket so thebucket bottom is sitting level on the ground.

Dump bucket slightly to take weight off mount pins andallow for stand installation. Set brake and shut off trac-tor.

Figure 49. Stands Installed

Remove safety pins from side of the loader boomsecuring stands in cross tube. See Figure 48. Removestands and return safety pin to original position.

Secure both stands at equal positions in brackets oncross tube using pins provided. See Figure 49.

Remove mount pins from loader uprights.

Restart tractor and roll back bucket completely to raiseuprights from mounts.

DP11

MAN0554 (Rev. 2/16/2007) Installation 35

If loader uprights will not raise enough to disengagemounts, reinstall mount pins and lower each stand onehole position. Remove mount pins and continue dis-mount procedure.

When loader uprights disengage the mounts and arehigh enough to clear the tractor tires, shut off tractorand disconnect hydraulic hoses.

Restart tractor and back away from loader.

STORAGE

Stored loader can fall and cause serious injuryor death. Securely store loader and attachments toprevent falling.

Secure equipment parking stand(s) in park posi-tion before detaching.

To provide necessary balance, loader framemust be equipped with bucket or attachmentbefore attaching or detaching from tractor, or whenloader is in stored position.

Do not climb or lean on equipment stored onstand.

Keep children and bystanders away from stor-age area.

Place mount pins in loader uprights and secure for lateruse.

Figure 50. Loader Storage Position (Typical)

CONNECT LOADER SUPPLY HOSES TO LOADERRefer to Loader Mounting Kit Manual for hose kit instal-lation.Connect loader supply hoses to loader feedlines at theright side of the loader.

Figure 51. Loader Supply Hose Connection

VERIFY CONTROL MOVEMENTS

Check that all tractor hydraulic control lever positionsoperate the loader movements correctly. See Figure52.

If loader movements do not respond correctly, shut offtractor, relieve pressure, and reconnect properly.Loader control movements must be correct before pro-ceeding.

Once all loader functions are correct, start the tractorand operate the loader to check for leaks. Purge anyremaining air from the hydraulic system and check oillevel.

When hose routing and correct loader operations areverified, identify each circuit by placing a matching col-ored band around the male and female quick coupler.The color-coded bands will make reinstallation easierwhen the loader is removed from tractor.

Figure 52. Single Lever Control Operation

A��WARNING

Yellow

Blue

Red

GreenDP16

● Handle forward - Boom down● Handle forward to limit - Float position● Handle back - Boom up● Handle right -

Dump bucket or attachment (slow)● Handle right to limit -

Dump bucket or attachment (fast)● Handle to left - Rollback bucket or attachment

36 Parts MAN0553 (2/23/2007)

LC96, LC96-2 LOADER ASSEMBLY

37

35. - Complete English Decal Set 36. - English Safety decal Set36A. - French Safety Decal Set 37. - Spanner Wrench

(Rev. 8/1/2012)

MAN0553 (2/23/2007) Parts 37

LC96, LC96-2 LOADER ASSEMBLY PARTS LIST

REF PART QTY DESCRIPTION

1 1025296 1 LC96 Boom(specify color when ordering)

2 1026530 1 Manual tube3 1006113 1 Bearing kit, 1.00 x 1.41 x 1.0

(Set of 2)3b 1025297 Bearing kit, complete set of 85 1023789 1 Feedline cover

7 1025300 1 Right upright(specify color when ordering)

8 1025301 1 Left upright(specify color when ordering)

9 1020348 1 Pin, 1.25 x 5.5010 1021529 4 Pin, 1.00 x 4.8811 1021528 4 Pin, 1.00 x 5.50

13 1021517 2 Hydraulic cylinder, 2.76 x 1.38 x 9.8014 1021514 1 Hydraulic cylinder, 1.77 x 1.18 x 19.62

(right hand)15 1021515 1 Hydraulic cylinder, 1.77 x 1.18 x 19.62

(left hand)17 21757 * 2 3/8 Flat washer SAE standard18 6697 * 1 3/8 NC x 1 Carriage bolt GR5

19 3597 * 2 1/8 x 1 Cotter pin21 4378 * 4 5/16 Flat washer standard22 56 2 Hose clamp 5/8


23 1005634 2 Pin, bent .5 x 4.023a 489009 * 2 Hair pin, 3/32

(included with item 23)24 56030 1 Bracket, bucket level indicator25 56075 2 Pull pin 1.25 dia. w/lynch pin

25a 62043 * 2 Klik pin .25 (included with item 25)26 1023777 1 Bucket level indicator rod27 1023780 2 Parking stand weldment

28 6096 * 2 5/16 NC x 3/4 HHCS GR529 6778 * 14 5/16 NC Lock nut30 7164 * 7 5/16 NC x 2-1/4 HHCS GR5

31 489009 * 2 Hair pin, 3/3232 14139 * 2 5/16 NC x Flange lock nut33 7501 * 7 1/4 - 28 Straight grease fitting

(included with pins) (not shown)34 88 * A/R Nylon cable ties (not shown)

(used to secure hoses to cylinders)35 1019720 Complete English LC series decal set

36 1018605 English safety decal set36A 1019721 French safety decal set37 1021841 1 Spanner wrench

38 1021842 1 Replacement pin kit (spanner wrench)39 14350 * 1 3/8 NC Flange lock nut45 480265 7 Feedline clamp 3/8

HHCS Hex Head Cap ScrewA/R As required

* Standard hardware, obtain locally

(Rev. 8/1/2012)

38 Parts MAN0553 (2/23/2007)

LC96, LC96-2 HYDRAULIC CYLINDER SEAL KITS NOTE: Check gland style and stamping on barrel before ordering seal kits.

LC96, LC96-2 HYDRAULIC HOSE ROUTING & PARTS LIST

Length Seal Kit

Cylinder TubeID

RodOD

Extended Retracted Spanner Nut Style "J"

Spanner Nut Style "E"

Threaded Rod Gland Style (No

Letter)

Threaded Rod Gland Style "E"

Complete Assembly

LC96 Boom 1.77 1.18 46.81 27.19 1023739 - 1023740 - 1021514 RH1021515 LH

LC96 Boom 1.75 1.12 46.81 27.19 - - - 1030142 1021514 RH1021515 LH

LC96 Bucket 2.76 1.38 27.92 18.12 1030145 1030140 1023742 - 1021517


22 56 2 Hose clamp 5/829 6778 * 14 5/16 NC Lock nut

34 88 * NS Plastic tie40 1023792 1 Feedline, boom cyl rod end (yellow)41 1023793 1 Feedline, boom cyl base end (green)

42 1023794 1 Feedline, bucket cyl base end (red)43 1023795 1 Feedline, bucket cyl rod end (blue)45 480265 7 Feedline clamp 3/8

46 1023782 2 Hose, 21" x 9/16 ORBM x 9/16 JICF48 1023784 4 Hose, 48" x 9/16 ORBM x 9/16 JICF

* Standard hardware, obtain locallyNS Not Shown

(Rev. 8/1/2012)

MAN0553 (2/23/2007) Parts 39

QUICK ATTACH BUCKET ASSEMBLY

PIN-ON BUCKET ASSEMBLY


1 2240060 1 60" Bucket1 2240066 1 66" Bucket

2 56378 1 60" Cutting edge (welded)2 56377 1 66" Cutting edge (welded)


1 2230060 1 60" Bucket (includes pins)

1 2230066 1 66" Bucket (includes pins)2 56378 1 60" Cutting edge (welded)2 56377 1 66" Cutting edge (welded)

3 1020348 1 Pin, 1.25 x 5.504 1021528 2 Pin, 1.0 x 5.505 6778 * 3 5/16 NC Lock nut

6 7164 * 3 5/16 NC x 2-1/4 HHCS GR5

* Standard hardware, obtain locally

40 Parts MAN0553 (2/23/2007)

QUICK ATTACH COUPLER


A 2200000 1 Attachment coupler assembly1 1019704 1 Right handle

2 1019705 1 Left handle3 1020348 4 Pin, 1.25 x 5.504 1021528 2 Pin, 1.0 x 5.50

5 300300 * 2 1/2 NC x 1 HHCS GR56 31392 2 Washer, 13/16 x 1-9/167 44575 2 Pin, 1.25 x 4.41

8 56392 4 Drive-Lok pin .37 x 1.259 56393 2 Compression spring .75 ID x 5.0

10 56395 2 Link, .37 x .63 x 7.30

11 56396 2 Washer, .18 x 1.5 x 2.2512 57470 2 Handle repair kit (incl. items 6 - 11)13 6778 * 4 5/16 NC Lock nut

14 7164 * 4 5/16 NC x 2-1/4 HHCS GR515 854 * 2 1/2 Flat washer standard16 45024 1 Decal, Warning, loader attach

HHCS Hex Head Cap Screw* Standard hardware, obtain locally

Appendix 41Bolt Torque & Size Charts (Rev. 3/28/2007)

BOLT TORQUE CHARTAlways tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual parts list.Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.

Diameter (Inches)

WrenchSize

MARKING ON HEAD

SAE 2 SAE 5 SAE 8

lbs-ft N-m lbs-ft N-m lbs-ft N-m

1/4" 7/16" 6 8 10 13 14 18

5/16" 1/2" 12 17 19 26 27 37

3/8" 9/16" 23 31 35 47 49 67

7/16" 5/8" 36 48 55 75 78 106

1/2" 3/4" 55 75 85 115 120 163

9/16" 13/16" 78 106 121 164 171 232

5/8" 15/16" 110 149 170 230 240 325

3/4" 1-1/8" 192 261 297 403 420 569

7/8" 1-5/16" 306 416 474 642 669 907

1" 1-1/2" 467 634 722 979 1020 1383

Diameter & Thread Pitch (Millimeters)

Wrench Size

COARSE THREAD FINE THREAD

Diameter & Thread Pitch (Millimeters)

MARKING ON HEAD MARKING ON HEAD

Metric 8.8 Metric 10.9 Metric 8.8 Metric 10.9

N-m lbs-ft N-m lbs-ft N-m lbs-ft N-m lbs-ft

6 x 1.0 10 mm 8 6 11 8 8 6 11 8 6 x 1.0

8 x 1.25 13 mm 20 15 27 20 21 16 29 22 8 x 1.0

10 x 1.5 16 mm 39 29 54 40 41 30 57 42 10 x 1.25

12 x 1.75 18 mm 68 50 94 70 75 55 103 76 12 x 1.25

14 x 2.0 21 mm 109 80 151 111 118 87 163 120 14 x 1.5

16 x 2.0 24 mm 169 125 234 173 181 133 250 184 16 x 1.5

18 x 2.5 27 mm 234 172 323 239 263 194 363 268 18 x 1.5

20 x 2.5 30 mm 330 244 457 337 367 270 507 374 20 x 1.5

22 x 2.5 34 mm 451 332 623 460 495 365 684 505 22 x 1.5

24 x 3.0 36 mm 571 421 790 583 623 459 861 635 24 x 2.0

30 x 3.0 46 mm 1175 867 1626 1199 1258 928 1740 1283 30 x 2.0

A

SAE SERIES TORQUE CHART

SAE Bolt Head Identification

SAE Grade 2(No Dashes)

SAE Grade 5(3 Radial Dashes)

SAE Grade 8(6 Radial Dashes)

A

METRIC SERIES TORQUE CHART

Metric Bolt Head Identification

8.8

MetricGrade 10.9

10.9

MetricGrade 8.8

A

A A

Typical Washer Installations Lock Washer

Flat Washer

8/9/00

Bolt

42 Appendix Bolt Torque & Size Charts (Rev. 3/28/2007)

BOLT SIZE CHARTNOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.

ABBREVIATIONSAG .............................................................. AgricultureASABE ....................American Society of Agricultural &

Biological Engineers (formerly ASAE)ASAE....... American Society of Agricultural EngineersATF................................Automatic Transmission FluidBSPP............................. British Standard Pipe ParallelBSPTM................ British Standard Pipe Tapered MaleCV ....................................................Constant VelocityCCW.............................................. Counter-ClockwiseCW .............................................................. ClockwiseF .......................................................................FemaleFT.............................................................. Full ThreadGA .....................................................................GaugeGR (5, etc.)........................................... Grade (5, etc.)HHCS ........................................ Hex Head Cap ScrewHT ...........................................................Heat-TreatedJIC................. Joint Industry Council 37° Degree FlareLH................................................................. Left HandLT ...........................................................................Leftm ........................................................................ Metermm ............................................................... MillimeterM ..........................................................................Male

MPa ........................................................ Mega Pascal

N ......................................................................Newton

NC...................................................... National Coarse

NF ...........................................................National Fine

NPSM .................... National Pipe Straight Mechanical

NPT...........................................National Pipe Tapered

NPT SWF......... National Pipe Tapered Swivel Female

ORBM ...........................................O-Ring Boss - Male

P .......................................................................... Pitch

PBY.......................................................Power-Beyond

psi ......................................... Pounds per Square Inch

PTO......................................................Power Take Off

QD ................................................... Quick Disconnect

RH.............................................................. Right Hand

ROPS........................... Roll-Over Protective Structure

RPM........................................Revolutions Per Minute

RT ........................................................................Right

SAE.......................... Society of Automotive Engineers

UNC ..................................................... Unified Coarse

UNF ..........................................................Unified Fine

UNS ..................................................... Unified Special

5/16 3/8 1/2 5/8 3/4 7/8SAE Bolt Thread Sizes

MM 25 50 75 100 125 150 175

IN 1 7

Metric Bolt Thread Sizes8MM 18MM14MM12MM10MM 16MM

2 3 4 5 6

Index 43MAN0553 (2/23/2007)

INDEXASSEMBLY

Dealer Set-Up Instructions 30

DEALER CHECK LISTSDelivery (Dealer’s Responsibility) 33Pre-Delivery (Dealer’s Responsibility) 33

DEALER SERVICECylinder Repair

Spanner Nut CylinderAssembly 27Disassembly 27

Threaded Rod Guide CylinderAssembly 28Disassembly 28

Pivot Bearing Replacement 29

GENERALAbbreviations 42Bolt Size Chart 42Bolt Torque Chart 41General Information 3Introduction 2Obtaining Replacement Manuals 2Specifications 4Table of Contents 3Warranty

Product 45Replacement Parts 44

INSTALLATIONAttach Loader to Tractor 34Connect Loader Supply Hoses 35Remove Loader from Tractor 34Verify Control Movements 35

OPERATIONBale Spear Operation 18

Picking Up Round Bale 18Picking Up Round Bale on Slope 18Transporting Round Bale 18

OPERATION (CONTINUED)Cleaning

After Each Use 20Extended Storage 20

Connect Bucket using Quick Attach Coupler 13Forklift Operation 17Grapple Operation 19

Dumping Load 20Removing Hay & Silage 19

Handling Objects 17Loader Operation 13

Backblading 16Backfilling 17Carrying Load 14Dumping Bucket 15Filling Bucket 14Lifting Load 14Loading from a Bank 16Loading Low Trucks or Spreader 16Lowering Bucket 15Operating on a Slope 14Operating with Float Control 15Peeling and Scraping 16

Pre-Operation Check List(Owner’s Responsibility) 20

Tractor Preparation 12

OWNER SERVICELubrication

Pivot Bearings 22Pivot Pins 21

SAFETYDelivery (Dealer’s Responsibility) 33Pre-Delivery (Dealer’s Responsibility) 33Pre-Operation Check List

(Owner’s Responsibility) 20Safety & Instructional Decals 10Safety Rules 6Safety Symbols Explained 2

TROUBLESHOOTINGTroubleshooting 23

F-8494 (Rev. 10/3/2011)

WARRANTY(Replacement Parts For All Models Except Mow’n MachineTM

Zero-Turn Mowers)

Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material andworkmanship for a period of ninety (90) days from the date of delivery of the product to the originalpurchaser with the exception of V-belts, which will be free of defect in material and workmanship for aperiod of 12 months.

Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion ofWOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. ThisWarranty does not cover normal wear or tear, or normal maintenance items.

This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sellor otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaserin any way. There are no third party beneficiaries of this Warranty.

WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free ofcharge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance withthis Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)days after such defect or noncompliance is discovered or should have been discovered, routed throughthe dealer and distributor from whom the purchase was made, transportation charges prepaid.WOODS shall complete such repair or replacement within a reasonable time after WOODS receives theproduct. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OFREPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THISWARRANTY.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OFTHIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, ANDWOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arisingdirectly or indirectly from the product, whether such claim is based upon breach of contract, breachof warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generalityof the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues orgoodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred forlabor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.

This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability toobtain materials or manufacture replacement parts.

No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorizedto alter, modify, or enlarge this Warranty.

Answers to any questions regarding warranty service and locations may be obtained by contacting:

F-3079 (Rev. 3/2/2012)

Woods Equipment Company2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 USA

800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com

WARRANTYAll Models Except Mow’n MachineTM Zero-Turn Mowers

Please Enter Information Below and Save for Future Reference.

Date Purchased: ____________________________ From (Dealer): __________________________________________

Model Number: ____________________________ Serial Number: __________________________________________

Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forthbelow, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THEPRODUCT TO THE ORIGINAL PURCHASER.

All current model loaders and backhoes are warranted for two (2) years from the date of delivery to the original purchaser.

The warranty periods for specific parts or conditions are listed below:

Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected toimproper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materiallymodified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center.This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made with parts otherthan those obtainable through WOODS.

This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to athird party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.

WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured byWOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.

WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS, inits sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof ofpurchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through thedealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair orreplacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY.THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODSMAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTYOF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from theproduct, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legaltheory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenuesor goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery orrental; or (v) any other type of damage to property or economic loss.

This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacturereplacement parts.

No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS, itsauthorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty. Answers to any questions regardingwarranty service and locations may be obtained by contacting:

Part or Condition Warranted

Model NumberDuration (from date of delivery to the original

purchaser)

All units invoiced after 4/30/2012

Gearbox components

BW1260, BW1620, BW1800, BW1260X, BW1800X, BW2400

6 years

BW240HD, BW180HD, BW180HB, BW126HB, BW126XHD, BW180XHD

BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X, BB8400X,DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240, BW126X, BW180X

PHD25, PHD35, PHD65, PHD95, DS96, DS120, RCC42, RD990X, PRD6000, PRD7200, PRD8400,S15CD, S20CD, S22CD, S25CD, S27CD, S30CD BW15LH, TC/R74, TC/R68, TC/R60, TBW144,TBW180, TBW204

RDC54, RD60, RD72, TBW150C, TS/R60, TS/R52, TS/R44, HC48, HC54, HC60, HC72 3 years (1 year if used in rental or commercial applications)

Blade spindles RD990X, PRD6000, PRD7200, PRD8400, TBW144, TBW180, TBW204 3 years

Rust-through BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW126HB, BW180-3, BW180HB,BW180HD, BW1260, BW1800, BW240, BW240HD, DS1260, DSO1260, DS1440, TS1680 10 years

PART NO.

MAN0553

© 2007 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of WoodsEquipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manualare the property of their respective companies or mark holders. Specifications subject to change without notice.

Woods Equipment Company

2606 South Illinois Route 2Post Office Box 1000Oregon, Illinois 61061

800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com

loader nual - woods equipment company · the bale spear is to be used only for handling bales. do...

Documents