lnformallon to users - library and archives canada of fine-celled plastic/wood-fiber composites...
TRANSCRIPT
lNFORMAllON TO USERS
This manusaipths bœn mpmchcd fEDm the miaolüm master. UMI flrns
the text di* fram the original or ooqy wknitted. Thus, sorne ümsis anâ dissertation copies are in typewnteer face, Mile atiers m y be fFom any type oî cornputer printer.
The qurlity d thb rrpmductian k -nt upan the qurlity of the copy submiüed. Brokm w indistinct print, odored or poor qualii illustrations
and photographs, print bhdthmugh, Wstandarâ margins, and irn-
alignment can advedy afbct reproduction.
In the wilikely event that the author did mrt send UMI a complete manuscript
and there are missing pages, these will be noted. A h , if unauthorized
copyright material had to be removeâ, a note will indicate ttie deletion.
Oversue materials (0-g., w s , drawings, charb) are repmduCBd by
sectiming the original, beginning at the upper left-hand corner and cmtinuing
from left to rigM in equal -ans with small overlaps.
Photographs included in the original manuscript have been reproduœd
xemgraphically in this copy. Higher quality 6' x W bbck and white
photographie prints are availabie for any photographs or illustrations appearing
in this copy for an a d d i i l charge. Contact UMI di* to order.
8811 & Huwell Information and Leaming 300 North Zeeb Road, Ann Arbor, MI 481 06-1346 USA
806521-0600
Extrusion Foaming of PlastidWood-Fiber Composites Using a Chemical Blowing Agent
Ghaus Muhammad Rizvi
A thesis submitted in conformity with the requirements for the degree of Master of Applied Science
Department of Mechanical & Industrial Engineering University of Toronto
O Copyright by Ghaus Muhammad Rizvi ( 1998)
National Library 1*1 of Cacada Bibliothèque nationale du Canada
Acquisitions and Acquisitions et Bibliog raphic Services services bibliographiques
395 Wellington Street 395. rue Wellington OnawaON KlAON4 OnawaON K l A W Canada Canada
The author has granted a non- exclusive Licence allowing the National Library of Canada to reproduce, lom, dismbute or sel1 copies of this thesis in microforrn, paper or electronic formats.
L'auteur a accordé une Licence non exclusive permettant à la Bibliothèque nationale du Canada de reproduire, prêter, distribuer ou vendre des copies de cette thèse sous la forme de microfiche/nlm, de reproduction sur papier ou sur format électronique.
The author retains ownership of the L'auteur conserve la propriété du copyright in this thesis. Neither the droit d'auteur qui protège cette thèse. thesis nor substantial extracts from it Ni la thèse ni des extraits substantiels rnay be printed or othenvise de celle-ci ne doivent être imprimés reproduced without the author's ou autrement reproduits sans son permission. autorisation.
Extrusion Foaming of PlastidWood-Fiber Composites using a Chemical Blowing Agent
Ghaus Muhammad Rizvi M.A.Sc., 1998, Department of Mechanical & Industrial Engineering
University of Toronto
ABSTRACT
This Thesis presents a study on feasibility of continuous extrusion processing for the
manufacture of fine-celled plasiic/wood-fiber composite foams. The main benefits of
incorporating wood-fibers in plastics are the increased stiffness and lowered cost of the
resulting composites. However, these improvements are usually accompanied by loss in
the ductility and impact resistance of the composites. These shortcomings can be
removed by effectively foaming and incorporating a fine-ceIl structure in the composites.
,Moisture removal is an important requirernent for improving the foam structure. Various
schemes of onIine moisture removal were explored and a promising process for the
production of fine-celled plastic/wood-fiber composites foams has been developed,
HDPWwood-fiber composite foams, with significantly improved ce11 structure and a high
volume expansion ratio up to nine-fold. have been successfully produced. For less
stringent requirements. the tèasibility of using the water, inherently present in the wood-
fiber, as a blowing agent was also explored. The addition of a nucleating a,oent
significantly improved the ce11 structure of PS/wood-fiber composite foams.
I would like to thank my supervisor Professor Chui B. Park for his guidance and
encouragement in the research. 1 would also like to thank Materials and Manufacturing
Ontario (MMO), CertainTeed, CRF Technologies Group Ltd. and Dupont Canada for
their funding and support in this project.
1 wish [O acknowledge the help and support of my past and present colleagues in
the Microcellular Plastics Manufacturing Laboratory at the University of Toronto. They
include: L. Matuanri. A. Behravesh, A. Yueng, D. Fernandes, F. Liu, Dr. Y. Liu. G. Liu.
H. Naguib. D. Ladin. S. Park, H. Zhang. R. Pop-Iliev, A Xie, X. Guan and J. Xu. I ais0
want to acknowledge the professional & technical support froin Mike Smith. Jeff
Sansorne and Dave Esdaile in the Machine Tool Laboratory.
Above all, 1 would like to acknowledge the immense support. patience and
understandin,o extended by my wife Sameena and my children Rem, Ghazi and Rarizi.
Wi thout their sacrifice. it would have been impossible to continue studies at this stage of
rny lifc.
Abstract
Acknowledgments.. .
Table of Contents
Nomenclature
List of Tables
List of Fi, cures
Chapter 1 Introduction
1 . 1 PlastidWood-Fiber Composites
1.2 Foams
1.3 Motivation of Thesis and Objectives
1.4 Microcellular Foams
1.5 Design of Experiments
1.6 Ovsrview of the Thesis
Chapter 2 Literature Review
2.1 Pimtic/Wood-Fiber Composites
2.1.1 FiIlers in Polymers
2. i -2 Processing and Nature of Fibers
2.1.3 Coupling Agents and Surface Modification
2.2 Thennoplastic Foams
2.2.1 Conventional Continuous Foarn Processing
2.2.2 Batch Microcellul~ Processing
2.2.3 Semi-Continuous Microcellular Processing
2.2.4 Continuous Microcellular Processing
2.3 Foaming of plastic/Wood-Fiber Components
1 V
vii
Chapter 3 Detailed Design & Construction of the Experimental Equiprnent
3.1 Design of Plastic/Wood-Fiber Extrusion Systern
3.1.1 Overview of the System
3.1.2 Extruder
3.1.3 Diffusion Enhancing Device
3.1.4 Heat Exchanger
3.1 -5 Force- Fed Hopper
3.2 Design of the Vented Extrusion Equipment
3.2.1 Overview of the System
3.2.3 Gear Pump
3.2.3 Modification of Diffusion Section.
Chapter 1 Foaming of PSIWmd-Fiber Composites in Extrusion Using
Moisture as a Blowing Agent
4.1 Introduction
4.2 Experimental
4.2.1 mate riais
4.2.2 Thermogravimetric Analysis of Wood-Fibers
4.2.3 Differential Scanning Calimetry
4 -24 Blending
4.2.5 Extrusion Setup
4.2.6 Extrusion Foaming of the Composites
4.3 Results and Discussion
4.3.1 Thermogravimetric Analysis of Wood-Fibers
4.3.2 Effect of Moisture on Volume Expansion
4.3.3 Cell Nucleation Behavior of Plastic/Wood-fiber Composites
with Moisture, HC and Mineral Oil
3.4 Summary and Conclusion
Chapter 5 Foaming of P W d - f i b e r composites
5.1 Introduction
5.1.1. Requirement for Coupling Agent
5.1.2 Polyethylene (PE) Foams
5.1.3 Batch Process vs. Continuous Extrusion
5.2 Experimentation with Various System Configurations
5.2.1 Processing of LLDPWWood-Fiber Composite Foams using a
Single Screw Extruder
5.2.2 Processing of HDPE/Wood-Fiber Composite Foams using a
Single Screw Extruder
5.2.3 Processing of LLDPENood-Fiber Composite Foam using a
Vented Extruder
5.2.4 Processing of LLDPEi'Wood-Fiber Composite Foam using a
Master Pellet
5.2.5 Experiments of HDPE/Wood-Fiber Composite Foams Using a
Tandem Extruder Setup
5.3 Summary and Conclusions
Chapter 6 Summary, Conclusion and Future Work
6.1 Summary
6.2 Conclusions
6.3 Future Work
References
= diffusivity (crn2/s)
= diffusivity coefficient constant (cm2/s)
= activition energy for diffusion (I)
= universai gas constant ( JK)
= solubility of gas in the polymer ( ~ r n ~ / ~ or g(gas)/g(polymer))
= Henry's law constant (cm3 [STP]/g-Pa)
= saturation pressure (Pa)
= rate of nucleation (#/cm3s)
frequency factor of gas molecules joining the nucleus ( I l s )
concentration of gas molecules in solution (#/rn3)
Gibbs free energy of bubble nucleation (J)
Boltzman constant (J/K)
temperature (K)
inrerfacial tension (mllm')
gas saturation pressure or pressure drop (Pa or psi)
Reynolds number
flow rate (@/min)
specific gravity
viscosity or melt viscosity (cP)
= inside pipe diameter (in)
= volume flow rate (m3/s)
vii
D
No
RPiM
v f
Vpo~~rncr
qb[ouinp agrni
@
R f
HC
TGA
LLDPE
HDPE
PS
HIPS
diameter of the cell (m)
cell-population density (cells/cm3)
rotational speed (roundmin)
theoretical maximum volume expansion ratio
specific volume of the polymer
blowing agent efficiency (5%)
surface to volume ratio pçr unir volume (m-')
radius of the extrudate (m)
Hydrocerol Compound
Thermal Gravimetric Andyzer
Linear Low Density Polyethylene
High Density Polyethylene
Polystyrene
High Impact Polystyrene
LIST OF TABLES
Table 4.1 : Difierent fomrilrrtions of composites . . . . . .. . ... ...... ..
Figure 2.1 :
Figure 2.2:
Figure 2.3:
Figure 2.4:
Figure 2.5 :
Figure 2.6:
Figure 3.1 :
Figure 3.2:
Figure 3.3:
Figure 3.4:
Figure 4.1 :
Figure 4.2:
Figure 4.3:
Figure 4.4:
Figure 4.5:
Figure 4. 6:
Figure 4.7:
Figure 4.8:
Figure 4.9:
Figure 5.1 :
Schematic of the Celuka process.
Schematic of free-rise foaming extrusion
Schematic of the batch process.
A schematic of a Microcellular Continuous Process
Modeling of gas escape and cell coalescence in extruded foams at a high temperature of polymer melt
Ce11 coalescence phenomenon caused by rupture of the thin membrane separating two ceils
Schematic of the mixing stage
The designed heat exchanger.
Force feed hopper.
Schematic of the gear pump
Experimental Set-up.
TGA thermograms for the devolati lization of wooc i fibers.
Effects of material compositions and extrusion foaming temperature on the expansion ratio of foamed composites
Effects of temperature variations on the specific volume of the foamed composites
DSC Thermograms of PS & HE'S
Maximum achievable volume of wood-fiber composites.
Effects of marerial compositions and extrusion foaming temperature on the ce11 population densities of foamed composites.
SEM micrographs of PS/wood-fiber composite foams
SEM micrographs of HIf S/wood-fiber composite
Effect of nozzle temperature on the expansion ratio of LLDPE/wood-fiber compositç foams processed with 1 wt% HC. Series A represents composites produced with undried wood- fibers. and series B A represents composites produced with dried wood-fi bers.
Figure 5.2:
Figure 5.3:
Figure 5.4:
Figure 5.5:
Figure 5.6:
Figure 5.7:
Figure 5.8:
Figure 5.9:
Figure 5.10:
Figure 5.1 1
SEM micrographs of a) LLDPEYwood-fiber composite foams (a) using undried and (b) dried wood-fibers
Theoretical expansion ratio for a composite foam having 20 wt% wood-fiber.
Volume expansion behavior of HDPE/wood-fiber composite foams using HC as a CBA
SEM microgragh of HDPE/wood-fi ber composite foam wi th ten- fold expansion
Venting extruder with gear pump
modification in the extrusion setup with a gear pump
Volume expansion behavior of LLDPE/wood-fiber composites while using a venting extruder with a gear pump
Volume expansion behavior of HDPE/wood-fiber composite foams in a tandem extrusion setup
SEM rnicrogragh of HDPEhood-fiber composite foam from a tandem extrusion system with nine-fold expansion.
Schernatic of a devolatilization tandem extrusion system
Introduction
1.1 PlastidWood-Fiber Composites
During the last few decades, thermoplastics have gained e ver-increasing
ricceptance as an important family of engineering materials and are steadily replacing
metals in a wide variety of applications. The commercial consumption of therrnoplastics
hris grown at an average rate of more than 6% per year during the last decade and this
trend is expected to continue in the foreseeable future. with the consequent increase in
their prices [1,2]. This situation has created an impetus for cost reduction by utilizing
fillers in thermoplastics [3]. Composite materials also offer an opponunity for utilizing
the favorable propenies of the constituent components.
Presentl y, the fi ber-reinforced plastic composites market, which represents one
third of al1 performance plastics, is dominated by glass fiber (93% of reinforcement
materials) [4] and some other inorganic fillers such as talc, mica, clay. and calcium
carbonate. These high-density conventional fillers offer wide property changes in the
composites but on a volumetric bais, their use is not cost-effective [ 5 ] .
In the last decade, natural organic rein forcements such as lignocellulosic-fibers
Oes over most have penetrated slowly into this market, because they offer many advanta,
common minera1 fillers. They are abundantly available, have lower cost and density,
resu l t in reduced Wear of processing equipment, and are renewable, recyclable, non-
tiazrirdous and biodegradable. The replacement of inorganic fillers with comparable
cellulosic-fibers provides weight savings and decreases the cost without reducing the
rigidity of the composite [Il. Wood-fibers are predominantly the most extensively used
fibers among al1 the cellulosic-fibers used as filiers.
The cost and weight of wood-fibers is substantially lower than the other
commonly used filler materials. Plasticlwood-fiber composites can be a cost-effective
alternative to many filled plastics or metals in tems of bending stiffness or weight [3] .
The wood-fibers are non-abrasive so that reiativeiy large concentrations can be
incorporated into plastics without causing serious machine Wear during blending and
processing. Although plastic/wood-fiber composites have been commercialized. and can
compete with certain plastic and wood products, their potential industrial applications have
been limited because of their low impact strength and high density compared to natural
wood and certain plastics [6].
Impact strength and ductility of plastics can be significantly improved by
incorporating a fine ceIl structure into them [7]. Additional benefits of having a foarned
structure are the reduction in weight and cost. Therefore, it is reasonable to expect that, if
a fine ce1 led structure is successfully produced in plasticlwood-fiber composites. the
problems with impact strength and weight mentioned earlier cm be reduced or
eliminated. This would significantly increase the potentiai of industrial application for
these composites.
1.2 Foams
Foamed materials are plastics having voids or cavities, or in other words they
have a ce1 lular structure. Thennoplastic foams are produced by deliberately adding at
least one gas-generating substance such as a chemical blowing agent. a soluble gas. or
volatile liquid under pressure to the polymer melt, then altering the environment to cause
the gas-generating substance to yield discrete bubbles [8].
Foarns or cellular materials offer many advantages over traditional materials and
non-celluIar polymers. Forims are very cost-effective and have unique insulating
properties, impact-resistant characteristics. buoyancy. and outstanding strength-to-weight
rarios, among other attributes [8]. Plastic foams have important economic impact on
nearly every aspect of life today. High-density celluIar plastics are used in fumiture.
transportation, and building products. Low-density foams are used for shock mitigation.
insulation. and rigid packaging.
The ceIl morphology of the foams influences their characteristics. such as
strength. thermophysical, dielectric and other properties. Conventional foam production
methods generally yield non-uniform cells with ce11 size greater than t 00 -300 pm with a
wide ceIl size distribution. This causes a deterioration in their properties. Foarns having ri
uniformly distributed fine-celled structure exhibit superior insulation and impact
resistance when compared to conventional foarns.
1.3 MotivationofThesisandObjectives
As mentioned earlier, the ductility and impact strength are substantirill y improved
by incorporating a fine-celi structure into the plastic/wood-fiber composites. However. if
the cell structure is couse. the properties of the composite foams will be significantly
reduced and such composites will exhibit low tolerance to a repeated nailing or screwing
operation. This will reduce their ability to compete with wood in the lurnber market. It is
believed that very small and uniformly distributed cells will also prevent the ïüptuic of
composite during nailing and screwing operations, This provides the basic motivation of
this thesis, which is to produce fine celled plastic/wood-fiber composites in a continuous
cost-effective extrusion process. Increasing the expansion ratio, within the limits of the
envisaged application, can lead to further cost reduction.
At present. most commercial manufacturers are using chemical blowing agents
(CBA's) for making composite foams [9]. Therefore. this study focuses on the use of
CBA's, for foaming of plastic/wood-fiber composites, as an evolutionary step. Best
results are more likely to be obtained by direct injection of the physical blowing agent
(PBA) directly into the extruder barre1 at high pressure and temperature. This method will
also be more cost-effective as CBA's are expensive and have low gas yield. The
composite foams currently being produced in the industry have a very coarse structure
and the bubble size is of the order of a couple of millimeters. Therefore. if foamed
plastic/wood-fiber composites with a uniforrn distribution of cells smaller than 0.5 mm
are successfully produced. it would be of considerable importance and will provide
significant insight into the development of a still finer foarn structure.
Therefore, the objective of this research was to develop a system capable of
produci ng plasticlwood-fiber composites having a cell density of the order of 1 OE'
cells/cm3 and expansion ratio of up to 10.
1.4 klicrocellular Foams
The tcchnology for producing plastic foarns having extremely small ceIl size, Iess
than 10 Pm, and a large cell population, of the order of 10' cells/cm3, has been steadily
evolving over the last decade. These foams have k e n named microcellular foams. A similar
üpproach is adopted for producing a fine-celled structure in plastic/wood-fiber composites.
The concept of creating microcellular structure in a polymer was invented by Suh
et al. [IO] at the Massachusetts Institute of Technology in the early 1980's. The
development of these materials is based on the idea that the creation of a very large
number of microbubbles, smaller than the pre-existing natural flaws in a polymer. can
reduce the material cost and consumption in mas-produced plastic parts without
compromising mechanical properties.
The mechanism for producing a very fine cell structure is that a gas is first
dissolved into the polymer matrix and then a large number of bubbles are nucleateci by
inducing a therrnodynamic instability. This instability c m be created by rapidly dropping
the pressure across the extrusion die [IO- 151.
1.5 Design of Experiments
Since there is a very large number of primary variables including the processing
conditions. which affect the properties of the composites, a large number of experiments
would be rcquired to study them al1 at once. This would entail numerous experiments. a
substantia1 portion of which might prove to be of minimal value with regard to
information content. In order to reduce the number of experiments, a number of material
and processing parameters were kept constant, for example only 20 wt% of one grade of
wood-fiber was used in al1 experiments.
1.6 Overview of the Thesis
Chapter 2 contains the literature survey. it starts with a review of the composites and
their fillers and the usage of coupling agents. Conventionai foarns and their production
process are bnefly reviewed followed by a review of microcellular foarns and their
production.
Chapter 3 describes the actual design of different cornponents in the single screw
extrusion system. the vented extruder with a gear pump and finally a tandem exvusion
system. These include the extruders, a diffusion enhancing device, a heat exchanger, dies.
and other componen ts.
Chapter 4 describes the experiments conducted for studying the feasibility of using
the inherent moisture present in the wood-fiber as a blowing agent. The devolatilizing
characteristics of wood-fibers were studied using TGA and important processing limitations
were iden ti fied for plastic/wood-fi ber composite extrusion in general. PS and HPS/wood-
fiber composites were processed in extrusion and foamed successfulIy. The effect of using a
nucleating agent on the foam structure was also studied.
Chapter 5 describes the efforts made for producing PE/wood-fiber composite f o m s
using ri CBA. The key issue was the removai of moisture for achieving a good foam
structure. Efforts were made to do away the vacuum-oven batch drying process and to
dcvelop a continuous, online process for moisture removal. For this purpose, various
processing systems were developed and finally a promising system was identified.
Chapter 6 provides a surnmary and the conclusions of the research, along with
suggestions for future work based on the research results presented in Chapter 5.
Chapter 2
Literature Review
The use of wood-fibers in thennosetting resins is well established in products
such as particleboard and fiberboard. However, in therrnoplastics their use ris filler
material h a s been limited due their weak adhesion and poor dispersion [ 1,161. Recent
investigations into bondingkoupling agents that reduce the incompatibility between the
hydrophillic wood-fibers and the hydrophobic polymers, has provided an impetus for
producing plastic/wood-fibe r composites to make use of the rnany advantages offered by
these composites [!. 161.
2.1 PlastidWood-Fiber Composites
The products of cellulose materials, such as wood-fiber. combined with synthetic
plastics are known as plastic/wood-fiber composites. One of the advantages of combining
wood-fiber with plastic is to combine desirable properties of both components. hence
enhancing or extending their usefulness [ 1,6,8,17].
2.1. J Filfers in Plastics
The primary purposes for using a filler in ri thermoplastic composite are their
potential ability to modify the properties and to reduce the material cost. The fillers can
be either solid particulate or fibrous materials. The modification in properties can lead to
reduced tackiness. improved stiffness and scuff resistance, and enhanced electrical
properties and dimensional stability [ 18,193.
iMineral Fillers
Mineral filler-filled plastic composites have been used for many decades.
Calcium carbonate (&CO3) has been widely used in plastic composites because of the
cost advantages and other appealing properties including low plasticizer absorption and
strong resistance to thema1 degradation during processing. Silicates, silicas (clay, talc.
mica. etc.) and sulfates of the alkine-earth metals [barium (BaSOA) and anhydrous
calcium (CaS04) sulfates] constitute other inorganic filfers widely used. Ctays are useful
for some specific applications such as electric iiisulator products. In general, al1 the
fiIlers are mainly utilized with the aim of lowering material cost [18].
Another class of filler materials used in plastics can be termed as "functional
fillers". They include glass fibers and glass spheres, carbon fibers, fine-particle calcium
carbonates, etc. [19]. These fillers are mainly used for improving the performance of the
composite rather than for reducing its cost. Although these inorganic fillers are low-cost
on a weight basis, their high densities (specific gravity about 2.5) can increrise the cost on
a volume basis and make processing more difficult [2].
Organic Fillers
Organic fiilers such as wood-fibers, pulp-fibers. and sugar-cane husks are aiso
used for making polymer composites. They possess a low specific gravity (about 0.9),
and when used to extend resins, they offer a significant cost saving [2-4.6,7,17]. The use
of cellulosic fillers is more common in polyolefins (polypropylene and polyethylene)
than in ot her thermoplastics. Most of the available literature on cellulosic-fiber fi lled
plastics can be classified into three groups: ( 1 ) study of the processing parameters. (2)
effect of the nature or type of fibers, and (3) effect of coupling and adhesion promoters
on the performance of the composites.
2.1.2. Processing and Nature of the Fibers
The available literature indicates that, from among the many forms of available
cellulosic fillers, wood-fibers are the rnost favored form of fillers in most publications.
Yusko~~a et al. [20] studied the interaction energy between polymer and different forrns of
cellulosic-fibers (lignin, cotton linter, and wood-fiber) and found that wood-fiber
contributed the most desirable strength properties to the composite matrix due to its
highest adhesion interaction. Their study has also demonstrated the promising potential
of cellulosic-fibers to replace common inorganic fillers.
The incorporation of fibrous materials derived from cellulose into a plastic matrix
has also been studied extensively [3.7,21-241. The main reason for using tïbrous
cellulose materials lies in the tàct that these fibers are more able to resist degradation of
their aspect ratio during processing, which is essential for fibers to transfer stresses
effectively in the composites.
The effect of the nature of cellulosic-fibers in a plastic matrix has been studied by
.Maldas et al. [25]. The cellulosic-fibers used were derived from cotton. softwood and
hardwood in the forrns of different pulps (CTiMP. kraft, and sawdust). Based on
mechanical property testing, the authors concluded that the softwood fibers are preferable
to hardwood fibers in improving properties. Such disparity was explained by the
morphological difference between the more flexible softwood and stiffer hardwood fibers
as well as the aspect ratio of the fibers from the two wood species.
2.1.3. Coupling Agents and Surface Modifications
The strength performance of the cellulosic fiber/plastic composites is generally
low compared to unfilled polymer. The decreased strength is likely a result of poor
adhesion and/or dispersion of fibers due to the natural incompatibility of phases during the
mixing of the hydrophilic cellulosic fibers with the hydrophobic polymeric matrix. To
improve the adhesion between fibers and polymer, coupling agents are usually used.
Coupling agents are able to react chemically on both ends during processing, with the
fibers on the one side and the polymer on the other, thus creating a chemical btidge at the
interface. The resultant chemical bonding increases the ability of the matrix to transfer
stress to the fibers [26-281. Although coupling agents c m chemically react with both the
polymer and the fibers, there is some evidence that the reaction with the polymer is not
necessaril y a prerequisite.
In order to overcome the incompatibility between cellulosic fibers and plastics,
Kokta et al. have assessed the effects of various types of isocyanates [26], mateic
anhydride, and silanes [29] as coupling agents. The mechanical properties of hardwood
aspen in the form of CTMP pulp and sawdust [29] as well as Cotton fiber [26] with two
types of PVC resins (Baron and Goodrich) were investigated. The results showed chat
the type and concentration of coupling agents used influenced the performance of the
composites to a considerable extent. For example, the tensile and flexural properties of
the isocyanate treated wood-fibers composites were increased compared to the
composites with untreated fibers. When used with a moderate concentration (0.5 to 5 %
by weight), isocyanate acted as an adhesion promoter and offered the maximum
enhancement of mechanical properties whereas with greater concentration the properties
deteriorated.
The main drawbacks of cellulosic-fibers filled polymer are their relatively low
degradation temperature (about 200°C) and their water sorption. which weakens their
adhesion with the hydrophobic matrix.
Goettler [30] studieci the extrusion of PVC hose products reinforced with short
cellulose fibers at the temperature range of 138 to 160°C. His study revealed that with
intimate interfacial bonding between fiber and matrix, a composite's tensile strength
could be doubled over thar of a poorly bonded composite. In addition, desirable
dispersion of cellulose fibers in plasticized PVC could be accomplished if sufficient
shearing stress was generated during compounding. High shearing stress helped not only
break up fiber agglomerate. but also minimize structural defects caused by fiber
agglomerates.
2.2 Thermoplastic Foarns and their Processing
Foamed plastics are materials having voids or cavities. or in other words they
have a cellular structure. Thermoplastic foams are produced by deliberately adding at
lerist one gas-generating substance such as a chernical blowing agent, a soluble gas. or
volatile liquid under pressure to the polymer rnelt, then altering the environment to cause
the gas-generating substance to yield discrete bubbles [8].
2.2.1 Con ventional Continuous Foam Processing
A good review of conventional polymeric foams and their processes is given in
[3 1 1. Polymeric foams can be produced in such processes as extrusion, injection molding
and compression molding. The selectior! and design of an appropriate process are
governed mainly by the material characteristics, and thus it is impossible to offer a single
process for al1 polymeric materials. However, fundamentally, al1 foaming processes are
sirnilrir.
In genera1, a foaming process consists of three main steps: formation of ü
polymer/blowing agent solution/mixture, ce11 nucleation, and cell growth. One of the
conventional foam processes is the "Celuka Process" [32] (a schernatic is s h o w in
Figure 2.1 [33]). In this process, the polymer is meited in an extruder. and a blowing
agent is then injected which is mixed with the polymer and is dissolved in it. In some
foam processing. the injected blowing agent does not completely dissolve in the polymer
melt. The rnelt containing the blowing agent is forwarded to the head of the extruder.
which is partiaIly plugged with a torpedo or mandrel. The melt then flows into a cooled
shaper connected to the head of the extruder. The outer layer of the extrudate therefore
cools and forms a skin Iayer. The foaming proceeds inward from the outer layer to the
ccnter of the extrudate. In this process, virtually no cell nucleation occurs in the meIt
before it flows into the shaper. Ce11 nucleation is initiated in the shaper, where ceil
growth also proceeds. In fact, in ail the conventional processes, ce11 nucleation and ceIl
growth takes place simultaneously.
The Celuka process is a "controlIed foam extrusion ( C E ) " process in which the
foam product consists of a solid skin and a cellular core. In a CFE process. the extrudate
is mechanical1y constrained by a cooled shaper and thus is forrned to the shaper profile.
Moreover, since the outer layer of the foam product is cooled and a solid skin is formed,
the diffusion of the blowing agent from the outer surface to the atmosphere (or blowing
agent escape) is prevented. However, the blowing agent can be still lost through the hot
inner surface where foam growth occurs. This process can be used to produce foam parts
with ri wall thickness of over 6 mm [3 I l .
In contrat to a CFE process, a conventional "free foaming extrusion (FFE)"
technique allows the foaming article to expand without constraint. A schematic of an FFE
process is shown in Figure 2.2. The temperature of the melt rit the die exit plays an
important role in determining the fina1 properties and the amount of expansion [34]. This
process is suitable for products with a wall thickness in the range of 2-6 mm [3 1 1 .
In a conventional foam process, foam products of various densities can be
produced. However, the state-of-the-an foams have a full y-grown ceIl size greater than
100 Pm. a ce11 population density lower than 106 cells/cm3. and a non-uniform ceil size
distribution [3 1,351. Hence. the mechanical properties of the conventional foams are
poor.
In conventional foam processing, the most commonly used blowing agents are
FCs, CFCs. n-pentane. and n-butane [36]. These agents can dissolve into the polymer
rcsin in large quantities due to their high solubility [37]. For instance. the solubility of
FC-1 14. a commonly used blowing agent. in polystyrene is above 20% by polymer
weight at a pressure of 1000 psi and a temperature of 200°C 1371. This suggests that a
foam product with a high void fraction can be produced at a relatively low pressure in the
system. In addition, the loss of blowing agent from the extrudate during expansion is
small since the diffusivities of such agents are low due to their large rnolecular size 1381.
This allows the extrudate to expand significantly, Therefore, the final product hm a low
foam densi ty. Despi te the favorable properties of the conventional blowing agents. there
are major concerns in utilizing them. For instance, CFCs are known to deplete the ozone
layer and their use has been stopped by the Montreal Protocol [39]. The other long chain
blowing asents such as n-pentane and n-butane are also hazardous because of their high
flarnmability. Therefore. aitemative biowing agents should be developed in polymer
foam processing.
2.2.2 Batch Microcellular Processing
,Microcellular polymers were first produced in a batch process 1401. A schematic
of the batch process is shown in Figure 2.3. In this process, a polymer sample is placed in
a high- pressure chamber connected to a gas reservoir. The gris can be either nitrogen
(Nz) or carbon dioxide (CO?). The poIymer sample absorbs the gas and. after a sufficient
time, reaches a saturation state. The amount of gas dissolved in the polymer plays an
important role in the final foam quality. When the sampIe is fully saturated with the p.
the pressure is rapidly decreased to cause a sudden drop in the solubility of the gas in the
pol ymer. This initiates a thermodynarnic instability, which drives nucleation of billions of
microcells. These rnicrocells cannot expand significantly, as a large amount of gas is lost
during cell growth. The foaming of the sample in the batch process is initiated by heating
through the surface of the sample. Since the temperature of the foam skin is always the
highest during the foaming process, the gas can easily escape through the hot skin to the
atmosphere. Therefore, the sample expands to a lesser degree, which depends on the
amount of gas left in the sample and used for ceil growth. However, the foam products
have a small ce11 size on the order of 10 pm due to the presence of a large number of
nuclei generated in the polymer matrix.
In a batch process, ceil nucleation is governed mainly by the saturation pressure
(or pressure drop), and ce11 growth is governed by the heating temperature and time.
Hence. the nurnber of nucleated cells and the amount of expansion can be independently
controlled. It musc be noted that in a batch process, the foaming temperature is in general
chosen to be the lowest to make the ceIl growth step easily controllable f22]. When the
nuclei are generated. their growth is retarded due to the high stiffness of the polymer
matrix at the Iow temperature. However, this prevents the degradation of the foam
product due to coalescence of the cells. Growth of cells can be controlled by modulating
the temperature and the time of exposure to heat.
A major disadvantage of the batch process is that a very long time is required for
saturation of gas in the polymer. This is due to a low rate of gas diffusion into the
polymer at room temperature. For instance, the diffusivity (D) of CO2 in polystyrene at
room temperature is 6x 10-%rn2/s [41]. The diffusion time can be estimated using the
fol lowing equation:
where lr is the thickness of the sample. For a sample of 1 mm thickness, the diffusion time
will be about i2 hours. As a consequence, the total processing time is too long, and thus
the batch process j not cost-effective.
iMatuana [2 1 -23,421 has reponed successful microceIlular foaming of ce1 lulosic-
fibers filled thermoplastics. The same process as described above was used, however, the
wood-fibers were treated to increase their adhesion with PVC. A ten-fold expansion was
re ported.
2.2.3 Sem i-Continuo 14s Microcellular Processing
Kumar and Schirrner f43] developed a semi-continuos process for production of
solid state PET foams. In this process, layers of polymer sheet are interleaved with gas
permeable materials (such as gauze, porous paper sheet, etc.). The roll of the interleaved
polymer and gas permeable material is saturated with an inert gas in a high-pressure
vessel. The polymer sheet is taken out from the vessel, unrolled. and separated from the
gas penneable material. The saturated sheet is drawn through a heating station with a
suftkient residence time to achieve a desirable foam density. In this process, the gas
tends to escape from the sheet after its removal from the vessel. Therefore. the foaming
must be processed promptly to avoid excess gas loss. In other words, only a finite length
of the sheet c m be foamed at one time, and hence. the process is called "semi-
continuoust'.
2.2.4 Cori finnous Microcellular Processing
In order to overcome the shortcomings of the batch process, a cost-effective,
continuous microcellular process has been developed in extrusion [ l 1-15]. A schematic
of the microcellular extrusion process is shown in Figure 2.4. In this process, a much
shorter time is needed for saturation of the polymer with gas. When the polymer is melted
in the extrusion barrel, a metered amount of gas is delivered to the polymer melt [13].
Three strategies are apptied to assist the complete dissolution of the injected gas
in the polymer melt. The first strategy is to inject and dissolve the gas at an elevüted
temperature. This can be explained by the following equation (4 11:
4 D = D,, exp(--), RT
where D = diffusivity, cm%.
Do = diffusivity coefficient constant. crn'ls,
.aD = activation energy for diffusion. J . and
R = universal gas constant, J/K.
-4s s h o w in the equation, the diffusion coefficient increases as the temperature increases.
Thus, the diffusion rate can be increased by processing the polymer/gas mixture at a
higher temperature.
The second strategy is to use convective diffusion [IO]. The idea of convective
diffusion is to bring the poIymer melt with low gas concentration into contact with the
bubbIes with high gas concentration. To achieve this, the bubbles are stretched by the
shear field generated by the screw motion: the stretched bubbles have a larger interfacial
area and a lower striation thickness in the polymer melt. The diffusion distance is greatly
rcduced. and thus, the gas can be diffused into the polymer more easily. Static mixers
can be added downstream of the extruder to enhance the shear mixing and ensure the
homogeneity of the polymedgas solution.
The third strategy is to increase the system pressure to increase the solubility of
gas in the polymer. The relationship between pressure and gas solubility can be
expressed by the following equation [41]:
where c, = solubility of gas in the polymer, cm3/& or g(gas)/g(polymer).
H = Henry's law constant. cm3 [STPIIg-Pa. and
p, = saturation pressure, Pa.
As shown in the equation above, the solubility of gas increases with pressure.
The diffusivity of CO2 in polystyrene at a temperature of 200°C is estimated to be
10-5 cm'ls [ 1 1.121. Thus, the time for gas diffusion into a 1 mm thick melt (or a diffusion
distance of 0.5 mm) is about 4 min (Equation 2.1 ). This represents a significant reduction
in the diffusion time which results in a much shorter processing time.
There are three essential steps in a continuous rnicrocellular extrusion process: i )
uniform formation of polymerlgas solution, ii) ce11 nucleation. and i i i ) ce11 growth. The
formation of a uniform solution of polymer and gas is essential in microcellular
processing, since pockets of undissolved gas can generate undesirabl y large voids. A
uniform solution can be achieved if the amount of gas injected is below the solubility
limit [13]. and dissolution of gas into the polymer is enhanced [ I 1,121. It must be noted
that evcn if an appropriate amount of gas is injected into the polymer melt. this does not
necessarily guarantee that a11 the gas will be completely dissolved into the polymer.
Moreover. complete dissolution of gas into the polymer melt must be ensured. before the
melt reaches the nucleation die. This can be achieved by reducing the gas diffusion
distance in the polymer (i.e., the striation thickness of the polymer and gas). The
diffusion distance is reduced due to the shear field generated by the motion of the screw.
In a shear field. the bubbles are stretched, giving a larger interfacial area and a lower
striation thickness. Cornplete diffusion can be ensured by using a diffusion-enhancing
device in which static mixers are placed to enhance shear-mixing [ l l ] . Microcell
nucleation occurs in a rapid-pressure-drop nucleation nozzie [12,14]. The rapid drop in
pressure causes a rapid drop in the solubility of gas in the polymer melt. This induces a
thennodynamic instability, as in the case of batch processing, which drives nucleation of
billions of microcells. The nucleated cells continue to grow at the die exit. The final foam
structure is determined by the conditions under which the three steps of the process are
perf'ormed.
In microcelIular processing, nucleation is induced by a thennodynamic instability,
which is achieved by using a rapid pressure drop device. Colton and Suh [Ml developed
a model of bubbie nucleation rate:
where I'? = rate of nucleation. #/cm3s,
f, = frequency factor of gas molecules joining the nucleus, I/s.
Co = concentration of gas molecules in solution. #/m3,
AG = Gibbs free energy of bubble nucleation. J.
k = Boltzman constant. J/K. and
T = temperature. K.
and AG can be expressed as:
AG = 1 4 v , h 3AP'
w here = interfaciai surface tension. rni/rn2, and
A P = gas saturation pressure. Pa.
Therefore, a higher nucleation rate can be achieved by increasing the saturation pressure
or blowing agent concentration. In addition, another important factor that affects the
nucleation rate is the pressure drop rate. The investigation of Park et. al [14] has shown
that the nucleation rate varies directly in proportion to the pressure drop rate. They
explained this phenomena by nucleation/cell growth competition for the dissolved g a . If
the pressure drop rate is high, there is relatively less time for the gas to diffuse into the
already nucleated cells, and the gas tends to nucleate an additional cefl. ffence, a greater
number of nuclei can be obtained by inducing a higher pressure drop rate.
Another important step in the formation cf microcellular foams is ceIl growth.
The nucleated cells grow as long as gas is availabte in the polymer matrix to diffuse into
the celIs, and the ce11 walls are pliant enough to expand- The rate of ceIl growth is
controlled by the diffusion rate and the stiffness of the polymer melt. Cell growth is
governed by the time allowed for the cells to grow, the temperature of the system. the
hydrostatic pressure or stress applied to the poiymer matrix. the viscoelastic properties of
the polymerlgas solutior?, and the degree of supersaturation 145.461. Cell growth must be
cürefully controlled because it affects not only the final foam density, but also the ce11
density, by preventing cell coalescence. Nitrogen or carbon dioxide, which are the
chosen blowing agents for the continuous process, have a small molecular size. They can
easily escape from the polymer foam to the environment. This will lead to colhpsed cells
and the foam density will be increased Figure 2.5. If the melt strength of the polymer is
too Iow, the ceIl walls will rupture due to the surface tension induced by cell growth [46].
A schematic of this phenomenon is shown in Figure 2.6. Consequently. the adjacent cells
will join together to f om one single cell. and the ceIl density will \je greatly reduced.
A great deal of research has been conducted on continuous microcellular foaming
[ 1 1 - 151. Most of it has focused on the nucleation phenornenon. Behravesh et al. 146-491
developed a process that can prevent cell coalescence and gas escape in the cell growth
stage. Cell coalescence was suppressed by cooling the poIymer/gas solution
homogeneously to increase the melt strength. The gas loss to atmosphere was controlled
by cooling the surface of the extrudate to forrn a solid skin layer, thereby preventing the
gas from escaping out of the polymer. The PS filarnentary foarn produced by this process
has a 40 fold volume expansion and a cell density of 5 x 10' cells/cm3.
2.3 Foaming of PlastidWood-Fiber Composites
There is not much published literature about continuous processing of
plristic/wood-fiber composite foarns. In fact, even the extrusion process for composites is
mostIy discussed in the context of injection molding. Only a few articles could be found
on production of plastic/wood-fiber composite foams, and invariably the processes are
based on injection molding. where foaming takes place in the mold 150.5 11. Pabedinskas
et al. [ 52 ] describe a continuous Celuka process for producing plastic/wood-fiber
composite foams. However, the ce11 structure achieved is extremely coarse.
A study, of the fundamental issues involved in the continuous extrusion of the
thermoplastic/wood-fi ber composite foams, is required in order to determine the
parameters for achieving the desired density reduction and a fine-celled structure.
I l Polyrner 1
j Blo~ving Agen t l
Diffusion
!.la to r - - - . d L . l A - - - L -
Sucleat ion Yozzle
Figure 2.4: A schematic of a Microcellular Continuous Process
coalesœd ceiis
gas escape
Figure 2.5 : ~Modeling of gas escape and cell coalescence in extruded foams at a h i t h temperature of polymer melt [39]
ccll ccll
Figure 2.6: Cell coalescence phenornenon caused by rupture of the thin membrane separating two cells
Chapter 3
Detailed Design & Construction of the Experimental Equipment
This chapter describes the design and construction of a new system dedicated to
the processing of polymer/wood-fiber composite foams. An extruder with variable drive,
a gear pump with variable drive, electronic transducers and controllers were purchased
from their respective suppliers. Al1 the interconnecting and other mechanical parts were
fabricatedhachined in the departmental machine shop at the University of Toronto. The
electrical control panel and rdated wiring were configured in the Microcelfular Plastic
.Manufacturing Laboratory of the department.
3.1 Design of PlastidWood-Fiber Extrusion System
3.1.1 OverviewoftheSystem
As the objective of this study is to develop fine-celled structure in plastic/wood-
fiber composite foams, it was decided to adopt an approach similar to that used for
producing microcellular foams. The first microcellular extrusion system was designed by
Park [53] for filament processing of styrenic polymers. Behravesh [47] used a sirnilar
system to produce microcellular foams of H P S and HI'PE. It consisted of a single screw
extruder. gas injection equipment, a diffusion enhancing device, a heat exchanger
(cooling system), and a filament die. It was decided to utilize a similar configuration
during this study for controlling the pressure and temperature of the plastic/wood-fiber
composite.
The objectives of the design are: 1 ) to plasticate the polymer/wood-fiber
composite in the extruder: 2) to decompose completely the CBA in the last stage of the
extruder and the diffusion device; 3) to ensure the hornogeneity of the composite/blowing
agent solution by using the diffusion enhancing device; 4) to avoid ceIl coalescence by
cooIing the meIt in the heat exchanger: and 5) to induce ce11 nucleation in the composite
melt in the die; and 6) to promote volume expansion outside the die. The detailed design
of each component is presented in the following sections.
3.1.2 Extruder
The extruder used in the single screw extrusion system consists of a ?4" laboratory
extruder (Brabender: 05-25-OOO), a 5 hp motor (Allen Bradley: 1329 Invener Duty
Motor) with a variable speed drive unit (Allen Bradley 1336 Impact). The screw is a
sinzle stase mixing screw (Brabender: 05-00-144) with a 30:l UD ratio. The purpose of
the mixing stage is to enhance the mixing of the polymer, wood-fiber and blowing agent.
A schematic of the mixing section is s h o w in Figure 3.1.
3.1.3 Diffzdsion Enliancing Device
A diffusion enhancing device is used to ensure that the constituents of the
composite and the decomposed gasses from the chemicai blowing agent are mixed
homogeneously. It was originally designed by Park [53] and modified by Behravesh
1471. It consists of an in-house design, rnild steel body, a static mixer (Omega:
FMX844 1 S), and a band heater (Omega: MB 1G 1 J 1 A 1 ). The rationale behind this design
is to use the static mixer to promote shear rnixing, and to maintain a high melt
temperature to promote a high diffusion rate of the blowing agent into the polymer melt.
In order to determine the required number of static mixer elements, a calculation
was done based on an equation provided by the manufacturer's technical brochure [54]:
where Re = Reynolds number,
Q = flow Rate, gal/min,
S = specific gravity,
p = viscosity, cP, and
D = inside pipe diameter, in.
A typical flow rate (Q) of the system is in the range o f 5-12 cm3/min ( 1 . 3 - 3 . 2 ~ 1 0 - ~
gal/min). The specific gravity (S) is approximately 1 for polystyrene, and the inside pipe
diameter (D) is 0.0 127m (0.5 in).
The viscosity is influenced by the shear rate and temperature. The apparent shear
rare ( ) in a circular channel can be calculated by the foilowing equation [54]:
With a channei diameter (D) of 0.07 m (0.28 in) and a flow rate (Q) of 10 cm3/min
( 2 . 6 4 ~ 10" @/min), the apparent shear rate is approximately equal to 4.95 l/s. From the
manufacturer's data sheet (Nova), the apparent viscosity of PS-IO1 is 3438.93 Pa's
(3438930 cP). With these values, the Reynolds number can be calculated using Equation
(3.1):
The pressure drop across the static mixer c m be determined using the following equation
[54] :
A P = Q x p x L , (3.4)
where L = larninar Factor (from the manufacturer), and
AP = pressure Drop, psi.
With a flow rate (Q) of 0.303 m3/rnin (2.64~10-3 gallmin), a viscosity (p ) of 3438930
cP. and a larninar factor (L) of 0.0588, the value of head loss is:
AP = ( 2 . 6 4 ~ 10-"x (3438930) x (0.0588) = 533.83 psi (3.68 MPa) (3.5)
This value is reasonable compared with a typical systern operating pressure over 27.58
iMPa (4000 psi). Based on the calculated results, it can be concIuded that a static mixer
with six elernents can fulfiil the mixing requirements. Additional mixing of the polyrner
meIt is provided by the rnixing stage of the extruder's screw.
3.1.3 Heat Exchanger
Ce11 coalescence is suppressed by cooling the polymer composite melt, which
increases the melt strength. It is important to cool the polymer melt homogeneously
because non-uniform temperature distribution could induce non-uniform ce11 growth,
which would result in a non-uniform ceIl structure. The heat exchanger was designed by
Behravesh [47]. It consists of an in-house design of a mild steel body and a static mixer
(Labcore: H-01669-12). This static mixer is different from the one used in the diffusion-
enhancing device. The mixer used in the diffusion-enhancing device does not promote
material transport in the radial direction. The static mixer used in the heat exchanger
directs the polymer fiow in the radiai direction such that the core material is constantly
being exchanged with the boundary materiai. According to the calculation by Behravesh
[47], four mixing elements can be used without causing too high a pressure drop.
Precise control of temperature is important for the uniform foaming of the
polymer. Use of band heaters with temperature controllers does not provide adequate
controt because of Iack of a cooiing source. To achieve better control, high temperature
oil (Labcore: iMode1 H-01294-40) was circulated in the outer channel of the heat
exchanger. The temperature of the oïl was controiled with an oil bath controller (Grant:
Mode1 W6-KD) which is equipped with a pump to circulate the oil to the heat exchanger.
A drawinz of the heat exchanger is shown in Figure 3.2.
3.1.5 Force- Feed Hopper
Becriuse of its Iow bulk density and its hydrophilic nature, wood-fiber has a high
propensity for adhesion. This tendency of adhesion makes it very difficult to feed the
plastic/wood-fiber mixture through the hopper opening into the bmel. Secondly, due to
the hygroscopic nature of wood-fibers in the composite mixture. it tends to absorb
moisture from the atmosphere during its long residence in the hopper.
To resolve these problems, a force-feed hopper was designed and constructed in-
house in the laboratory. Fig 3.3 shows a cross section of this hopper. It is provided with a
3/1" auger bit for forcing the dry blended mixture into the extruder barrel. The auger bit or
screw is connected to one half of a flexible and detachable coupling also s h o w in figure
3.3. The other half of the coupling is connected to a 12 V DC motor. with wonn and
wheel gears, mounted on the hopper lid. Two stiff vanes collect the mixed rnaterials and
guide it towards the rotating auger bit, which forces it down into the extruder barrel.
After filling the hopper with the dry blended mixture, the lid is closed so that the two
halves of the coupling engage. The material is forced into the barrel due to the motion of
the screw. The hopper is continuously purged with dry nitropen gas to prevent the
ambient moisture from entering it, thereby maintaining dry conditions within the hopper.
3.2 Design of the Vented Extrusion System
3.2.1 Overview of the System
The vented extrusion system consists of an extruder with a vent opening after the
second of the three heating zones of the barrel. The vent is normally used for removing
the volatile rnaterials from the polymers and additives. It was proposed to utilize this vent
for removing the water vapors present in the wood-fibers of the composite mixture.
As already described in chapter 1, the dissolution of the blowing gasses is a
nscessary condition for obtaining a large nurnber of nucleated bubble sites. This in tum
necessitates a high pressure in the dissolution section to increase the solubility of the gas
in the polymer matrix. During initial trials, the pressure at the extruder outlet could not
be increased substantially, as an attempt to do so resulted in excessive material Ioss
tlirough the vent. Therefore, it was decided to use a gear pump at the extruder outlet to
increase the pressure to the required level. The gear purnp, being a positive displacement
device, was not only expected to increase the pressure but also stabilize the flow rate, and
hence, improve the over al1 process control.
3.2.2 The Gear Pump
As suggested in section 3.2.1, a gear pump (Zenith: PEP-1 l ) , with a '/t hp motor
drive (Pacific Scientific: Model SR), a speed control unit (2enith: ZeDrive) and a
temperature controller (Eurothem Controls: Model 94). was used in the extrusion system
to control the pressure and polymer flow rate. The gear pun~p consists of two closely
intemeshing gears that rotate in a counterrotating motion to convey the polymer melt
frorn one end to the other. A schematic of the gear purnp is shown in Figure 3.4.
3.2.3 Modification of Dijjùsion Section
The results that were expected from the gear pump did not fully materialize,
although there was some decrease in the material loss through the vent. On reviewing the
design, it was noted that the molten plastic entering the gear pump contained decomposed
gasses from the CBA. Even if al1 the gasses were dissolved into the polymer before
reaching the gear pump, a substantial amount would rigain evolve into the gaseous phase
due to the reduced pressures encountered at the gear pump suction. This would render the
gear pump ineffectual.
To address the problem mentioned above, the process was redesigned. A new
decomposition/diffusion section, sirnilar to the heat exchanger described above [see
Figure 3-21, was constructed and added after the gear pump. For the new process, the
temperature from the vent up to and including the gear pump was kept under 160°C to
prevent CBA decomposition. After the gear pump, the temperature was increased to
205°C in the decomposition/diffusion section. This section was also provided with a
static mixer in order to improve the temperature homogeneity and effective
decomposition/diffusion. The extrudate was then cooled down to 150°C in the cooling
section and finally extruded through the nozzle die.
Figure 3.4: Schematic of the =car pump (courtcsy of Zcnith).
Chapter 4
Foaming of PS/Wood-Fiber Composites in Extrusion Using
Moisture as a Blowing Agent
4.1 Introduction
Foamed polymers can be produced by utilizing either a physical or chemical
blowing agent. The former can be either a gas (e-g., COz and Nz) or a liquid (e.g., CFCs
and other aIiphatic hydrocarbons) whereas the latter is usudly a solid [IO]. Nearly al1
these blowing agents have some problems associated with their usage. The use of CFCs
is banned in many countries because of their detrimental effect on the ozone layer,
whereas common aliphatic hydrocarbons are highly flammable. CBAs are known to be
expensivc, and yield low gas concentration during their decomposition.
As a result of persistent public pressure, the government continues to legislate
regulations aimed at enhancing environment protection and worker safety. The
development of an environmentally friendly, non-toxic, safe and low-cost blowing agent
may help the industry in coping with these regulations and simultaneously Save on the
cost of CBA. Since water, which is freely available, non-toxic and environment friendly,
c m be completely transfomed into a güseous state at tempentures above 100°C. i t is
belicved that it can potentially be uscd as a blowing agent in the production of foams in
an extrusion process. In this context, it is the purpose of this work to investigate the
feasibility of using the moisture in the wood-fiber 'as an alternative blowing agent for
producing foamed plastic/wood-fiber composites.
Water can be injected into the polymer melt in the extrusion foam processing like
other physical blowing agents [40]. However, since the sohbility of water in a
hydrophobic plastic is very low [ 3 6 ] , it may not be possible to completely dissolve al1 the
injected water in the plastic matrix during processing. Therefore, it is suggested that the
foam structure be developed by finely dispersing the water bubbles in the plastic matnx
followed by decreasing the pressure at a high temperature. However, the dispersion of
writer bubbles in the thermoplastic matrix would not be good because of the high surface
tension of water [69]. As a result, the ce11 structure would be neither fine nor
homogeneous. But since the dispersion of wood-fiber in the plastic can be independently
promoted by utilizing an appropriate coupling agent [2,7,59-6 1 1, md/or by intensive
mixing [60.6 1 1, the hy,oroscopic wood-fibers used as a filler can be utilized as a carrier to
distribute water in the polymer matrix. Although it is known that the coupling agents
have no significant effect on mixing of styrenic materials and wood-fibers [6 1 ] used in
this study, the well-known appropriate coupling agents for polyethylene, polypropylene.
and PVC can be effectively used to distribute widely the wood-fibers in the plastic matrix
[3.7.57.59,60].
This study investigates the feasibility of using moisture in the wood-fiber as an
alternative and cost-effective biowing agent in the production of plastic/wood-fiber
composite foams. Since water is different from other blowing agents in that it does not
dissolve to a significant degree in the polymer matrix, the foaming mechanism with water
would be different. The gradually released moisture from the wood-fiber during
processing can result in good dispersion of the released gas in the plastic matrix.
Therefore. a considerably better ce11 structure can be obtained by using the bound water
and/or the water of constitution released from the wood-fiber, rather than injecting the
water directly in the extrusion barre1 into the plastic melt. Another major difference of
writer compared to other blowing agents is that it condenses at about 100°C during
cooling of foam, thereby, creating low pressure in the cells. The possible contraction of
volume after foaming due to the vacuum created by the condensation of blowing agent is
discussed. A chemical-blowing agent is also used together with water, for comparison
purposes, to investigate the effect of each blowing agent on the foaming behavior of
wood-fi ber cornposi tes.
1.2 EXPERIMENTAL
42.1 Materials
The PS and HIPS used in this study were Nova 10 1 and Nova 3350. respectively,
supplied by Nova Chernicals. The wood-fibers were standard softwood (pine) grade
l2O?O, supplied by American Wood Fibers. 50 wt% of these fibers passed through the
sieve of 120 mesh s i x ( 1 25 microns) and were retained on 140 mesh (106 microns). The
moisture content and initial specific gravity of the fibers were 8% and 0.4, respectively.
A chemical blowing agent, Hydrocerol Compound (HC) suppl ied from Boehringer
Ingelheim was used with the intention of improving the ceII-population density of forimed
product. 1 wt% concentration of HC was chosen as a nucleating agent according to Ref.
[62] . Since HC was in a powder form, a small amount of commercial mineral oil (Life,
Phamaprix) was used, in order to uniformiy distribute the chemical blowing agent
particles into the plastic pellets [62] . On the other hand, no coupling agent was used for
processing the styrenic materials and wood-fibers as described above. All the materiais
were uscd as received,
4.2.2 Th ermogra vitneinTc Analysis of Wood Fibers
Therrnogravimetric analysis (TGA) was conducted to study thermal
devolatitization of moisture contained in wood-fibers using a TGA 2050 (TA
Instruments). A heating rate of 100°C/min was used. A typical arnount of material used
for the TGA experiments was 15 mg. The sample fibers were not oven-dried. The fibers
were initially heated up to 1 10°C and this temperature was maintained for 150 minutes.
The temperature was then increased to 200°C and maintained at this level for the
rernaining duration of the experiment (150 min). The oven was continuously purged with
nitrogen during the experiment to remove the released moisture and maintain dry
conditions. The purging also prevented the degradation of wood-fibers.
42.3 Differetltial Scanning Calorirnetry
Differcntial scanning calorimetry (DSC) was conducted to mesure the glass
transition temperatures (Tg) of PS and HIPS using a DSC 2910 (TA Instruments). A
typicd amount of material used for the DSC experiments was 5 mg. The plastic materials
were initially heated up to 770°C and this temperature was maintained for 20 minutes to
erase the thermal history. The temperature was then decreased to 25°C at a cooiing rate
of 1O0C/min.
4-24 Blending
Plastic petlets and a small amount of mineral oil (0.5 wt%) were mixed in a dry
blender. This was followed by the addition of 1 wt% of HC. The mixture was further
blended to ensure uniforrn distribution of the nucleating agent throughout the mixture.
FinalIy, 20 wt% of wood-fibers were added and further dry-blended to achieve
homogeneity. For both PS and WPS, three different types of mixtures were prepared and
the detailed description of the composition of each mixture is listed in Table 4.1.
Composition A was as described above, composition B was the same as A without HC,
and composition C had only polymer and wood-fibers.
Table 4.1 : Different formulations of composites.
- ---
Compositions (wt%)
A B C
4.2.5 Extrusio rr Setup
Figure 4. ï shows the experirnental setup used in this study. A force-fed hopper
for feeding plastic pellets and wood-fibers was designed and constructed at the University
of Toronto, as described in Chapter 2. The 3/4" single-screw extruder (Brabender 05-25-
PS or HPS
Wood-fi bers
Hydrocerol Compound
;Mineral oil
78.9 79.7 80.0
19.6 19.8 20.0
1 .O O .O 0.0
0.5 0.5 0.0
000) was driven by a 3.7 kW (5 HP) DC motor. At the extruder outlet is a diffusion-
enhancing device containinz a static mixer (Omega FMX8441S) to ensure the complete
dissolution of the gas generated from HC into the plastic matrix and water. This is
connected to the second heat exchanger, which uniforrnly cools the polymer/wood-fiber
composites using another type of static mixer (Omega P-04669-12) and an oïl bath
temperature controller. The elements of this static mixer are configured to transport the
core flow to the outer region and vice versa to impart a homogeneous distribution of
temperature across the radial cross-section. The extrudate finally passes through a nozzle
die having a diarneter of 1.27 mm (0.050") and length of 2.54 mm (0.100"). The nozzle
die is also cooled by circulation from an oil bath. A control panel equipped with
temperature controllers (Omega CN9000A) and pressure indicators (Omega DP25-S) was
used to monitor and control these parameters. Therrnocouples used were J type (Omega)
and the pressure transducers were Dynisco PT462E- 1OiM-6/ 18.
-1.2.6 Extriision Foaming of tJie Composites
The dry-blended mixtures were fed into the hopper. through which it was force-
fed into the extruder, The maximum temperature i
wris raised to 20j°C, to ensure the decomposition
cooling section, the temperature of the melt was uni:
n the barre1 and the diffusion section
of the hydrocerol compound. In the
fonnly reduced to 150°C. The nozzle
temperature was reduced from 150°C ( 1-2OC at a time). At different stable conditions,
samples were coIlected. The samples were dipped in liquid N2 and fractured. The
fractured samples were gold plated and SEM micrographs were triken for ceIl
chriracterization.
4.3 Results and Discussion
This section describes the experimental results of TGA analysis of wood-fiber and
foaming of plastic/wood-fiber composites with the moisture in wood-fiber. The
influences of HC on the volume expansion ratio and the ce11 population density are also
discussed.
4.3.1 Thermogravimetric Analysis of Wood Fibers
The amount of residual moisture in wood-fibers as a function of temperature was
investigated using a TGA to gain a fundamental understanding of the devolatilization
mechanisms of the free water. the bound water, and the water of constitution. Since the
wood-fibers are subjected to a high temperature for decomposing HC during the foaming
extrusion process, the devolatilization behavior of moisture from the wood-fibers was
investigated up to 205°C. A thermogram of devolatilization of wood-fibers obtained by
TGA analysis is illustrated in Fis. 2. It is clearly seen that at 1 10°C. the initially undried
wood-fibers start Iosing weight as soon as the experiment starts. Approximately 8% of
the moisture was removed from the fibers maintained at this temperature for 150 minutes.
However, it should be noted that most of the moisture loss (7.1 %) occurred during the
first 10 min of the experiment whereas an insignificant loss (0.9%) occurred during a
long period of heating time (more than 140 min). This loss of moisture is mainly due to
the drying of wood-fibers because the fibers were heated up abovc the boiling
temperature of water. The weight percent loss in moisture observed by the TGA analysis
azrees well with the 8% value of moisture content detemined by the oven-dry method
using the ratio of the weight of water to the weight of oven-dry wood. converted to a
percentage. This result implies that, during the extrusion process, some of the moisture
contained in wood-fibers may be released as soon as the compounded mixture enters the
hot extruder barrei. As a result, a substantial amount of water vapor escapes through the
hopper opening before being trapped in the molten mixture and pushed further
downstream into the extruder.
After heating up the wood-fibers at 1 10°C for 150 min. the temperature was
quickly raised to 205°C and maintained at that temperature for 150 minutes while
conti nuously purging with nitrogen. The thermogram of devolatilization of wood-fibers
shown in Fig. 2 clearly shows that even after wood-fibers are considered oven-dry, they
stili release water. An additional 3% moisture was released when the temperature was
raised from i 10°C to 205°C. This moisture is believed to be the water of constitution or a
small amount of remained absorbed-water that requires higher energy to dislocate. Since
the typical extrusion foam processing temperature and time are 200°C and less than 10
minutes, respectively, it is believed that the absorbed water and the water of constitution
can be dislodged during the foaming process and this water vapor could be utilized ris a
blowing agent.
43.2 Effect of Moistrrre on Volume Expansion
The feasibiiity of using water as a biowing agent in the production of foamed
plastic/wood-fiber composires was investigated. A chemical blowing agent was also used
together with water to investigate the effect of each blowing agent on the foaming
behavior of wood-fiber composites. Figure 3 shows the effects of material compositions
and extrusion foaming temperatures on the expansion ratio of foamed composites.
The experimentd results show that the inherent wood-fiber moisture can be
effectively used as a blowing agent for both PSIwood-fiber and HIPS/wood-fiber
composites. Depending on the type of the polymer, an expansion ratio of up to 20 was
successfull y achieved in the composites made with plastic and wood-fibers only
(composition C). However. it should be noted that without rnintral oil and HC. the
highest expansion ratio was obtained when PS was used as the polymeric material in the
composites. At the same extrusion foaming temperciture. the expansion ratio achieved in
PShood-fiber composite foams was significantly higher than that of HIPS/wood-fiber
composite foams. The maximum expansion ratios achieved in PSIwood-fiber and
HiPS/wood-fiber composite foams were 20 and 9 (for composition C), respectively, when
the extrusion foarning temperatures were in the range of 130°C to 140°C.
The difference of the volume expansion ratios obtained from the two composites
may be due to the stiffness of the plastic materials. When a foam structure is developed
by the moisture vapor at the die exit, volume expansion would occur quickly because the
moisture evaporates immediately at a lowered pressure. It should be noted that the cell
growth mechanism in the foam processing with water vapor is quite different from that
with other blowing agents. Most blowing agents, either physical o r chemicd. dissolve in
the polymer matrix before the onset of foaming at the die exit [63 ] . and therefore. the
nucleated cells grow as the blowing agent diffuses out of the polymer melt to the nuclei
[22.64]. But in the case of foaming with the moisture absorbed by the wood-fibers. the
blowing asent does not dissolve in the plastic matrix. and therefore, diffusion is not
involved in cell growth. As a result, it is expected that ceIl growth with moisture is faster
because the slow diffusion process is not involved although the rate of moisture release
from the wood-fibers is unknown yet. Since the volume of water vapor decreases as the
ten-iperature decreases as shown in Fig. 4, the foarned volume tends to decrease over time
as the extruded foam is cooled. Heat is lost through the foam skin to the environment
during cooling, and therefore, the temperature of the foam skin will be the lowest in the
foarn. As the foam skin is frozen at Tg, the total foam structure and volume will be
deterrnined by the conditions at this moment because of' the solidification of polymer. As
the foam is further cooled. al1 the polymeric materials will be solidified. However. the
water vapor inside the cells will start condensing to the liquid phase at 100°C, crenting a
vacuum in the cells, and the foam tends to colIapse. If the forrned plastic foam structure
is stiff enough, then the foam will not shnnk much even with the vacuum created in the
celis. But if the polymer is not stiff enough, then the volume expansion ratio will
decrease. It should be noted that HiPS is less stiff than PS due to the presence of mbber
particles. Consequently, the volume expansion ratio of HiPS/wood-fiber composite
foams blown by moisture would be lower than that of a PS/wood-fiber composite foams.
Since the onset of glass transition temperature, Tg was measured to be 105°C for both PS
and HIPS according to the DSC therrnograms s h o w in Fig. 5 , i t is not clear whether the
polymer matrix in the foamed composite was completely soiidified at the moment of
moisture condensation (100°C). However, since large expansion ratios were obtained
from the foams of these materials, at least the plastic material in the skin area of foam
must have been solidified first before condensation of water began. No significant effect
of mineral oil was observed on the volume expansion behaviors of PS/wood-fiber and
HIPS/wood-fiber composite foams.
When the chernical blowing agent was added, the volume expansion ratios of
HIPS/wood-fi ber composite foams were improved signi ficantly (Fig. 3b, Composition A)
whereas there was no significant change in the expansion ratios of PS/wood-fiber
composite foarns (Fig. 3a, Composition A). According to the manufacturer of the
chernical blowing agent, 1 wt% HC produces approximately 0.18 wt% CO2 and 0.18 wt%
water [65]. The specific volumes of CO2 at 100°C and room temperature are 703 cm31g
and 250 crn3/g respectively [70]. Therefore. the addition of î wt% HC will generate 1.27
c m h a d 0.99 c m h f COz volume per unit weight of composite at atmospheric pressure.
at 100°C and room temperature, respectively. Although the aniount of generated COz is
only sufficien( for about 100% volurnetric expansion, it helps significantly in reducing the
vacuum effect caused by condensation of water. As a result, the HPSlwood-fiber foams
are subjected to Iower compressive pressure differential, which improves the expansion
ratio substantially. in other words, although the HC was added as a ce11 nucleating agent.
i t also contributed to the volume expansion ratio of wood-fiber composite foams by
preventing volume contraction caused by water condensation. On the other hand. the
expansion ratios of the PSIwood-fiber composites were not affected much by adding 1
wt% HC. This implies that the PS/wood-tïber composite foams had not been contracted
by water condensation because of the high stiffness of PS.
The maximum achievable volume expansion ratio (a) of the composite foams
with the moisture in wood-fibers and the added HC can be theoretically calcuiated using
Eq. 4.1 [48] based on the assumption that al1 the gas is used for ce11 growth:
where v,, is the specific volume of blowing agent at the freezing temperature of polymer
and Vpolurnçr is the specific volume of polymer at room temperature; and nt,, and m,,iy,,r
are the mass flow rate of the gas and polymer respectively. It should be noted that the
specific volume of blowing agent is taken at the freezing temperature because the plastic
matrix structure is solidified at this point. It is assumed in this calculation of the
maximum volume expansion ratio that the air eventually diffuses into the vacuumed cells
after the foams are cooled to the room temperature and the foam shape is restored. For
wood-fiber composite foams, total volume expansion is caused by the moisture released
from the wood-fibers and the CO2 and water generated from the HC. The contribution of
moisture from the wood-fibers to the expansion is first calculated. If the amount of
moisture from the wood-fibers is assumed to be I I 93 of wood-fiber weight (Fig. 2), then
the total amount of moisture in the composite with 20 wt70 wood-fiber would be 2.2
wt%. Considering the specific volume of saturated water vapor to be 1873 crn3lg at 100°C
[67] , the maximum achievable expansion ratio is calculated to be 42.2, including its own
volume. If it is assumed that the wood-fibers are oven-dried or lose most of the water
vapor in the extrusion barre1 during plastication of polymer, the level of residual rnoisture
that can be used for foaming would be 3% of wood-fiber weight (Fig. 2). In this case. the
maximum achievable expansion ratio including its own volume is calcuiated to be 12.2.
The contribution of added HC can also be calculated. Considering the specific volumes
of CO2 (703 cm3/$) and saturated water vapor (1873 cm3/@ at 100°C. the maximum
achievable expansion ratio by 1 wt% HC (or equivalently 0.18 wt% CO-, and 0.18 wt%
water) is calculated to be 4.6. This value c m be added to the previously calculated
volume expansion ratio from the moisture in the wood-fibers for the foam processing
with composition A. Figure 6 shows the maximum achievable volume expansion ratio of
the composite foams with the moisture in wood-fibers and the added HC.
43.3 Cell Nucleation Behavior of PIustic/Wood-fiber Composites with Moisture, HC
and Mineral Oil
The ce11 nucleation behaviors of plasticlwood-fiber composites in foam
processing with moisture, HC. and minera1 oil were quite different from the expansion
behaviors. Figure 7 shows the cell-population densities of foamed composites as a
function of the materiais' compositions and extrusion foaming temperatures. Except for
the PSIwood-fiber composites foarned with moisture only (composition C), the measured
ce11 densities of PSlwood-fiber and HIPSlwood-fiber composite foams ranged from lo5
cells/cm3 to 106 ce11s/cm3. Since the processing temperature range was iow enough for
PS and HIPS, it is believed that ce11 coalescence did not occur [68]. Therefore, the final
ceil density of the foams would represent the number of cells nucleated in the early stage
of foaming.
The cell densities of HIPSIwood-fiber composite foams with moisture only
(composition C) were one order of magnitude higher than those of PSIwood-fiber
composite foams (Fig. 7). it seems that the mbber particles dispersed in the polymer
matrix enhanced ce11 nucleation although the cell nucleation mechanism in the foam
processing with water as a blowing agent is quite different from the foam processing with
other blowing agents [663.
When only minera1 oil was added in the formulation of the PSIwood-fiber
composites (composition B)? the ce11 density was dramritically increased (Fig. 7) although
there was no visible change in the volume expansion ratio of the PS/wood-fiber
composite foams (Fig. 3). This increased ceIl density in PSIwood-fiber composite foams
implies that the minera1 oil enhanced ceIl nucleation just as the rubber particles did in
HIPS. However, there was no significant effect of minera1 oil on the cell density of the
HIPS/wood-fiber composite foams.
The effect of adding HC on the ce11 density of the composites was also
investigated. To our surprise, there was no noticeable effect on the cell density for both
PSIwood-fiber and HiPS/wood-fiber composite foams although significant enhancement
of the ceIl density was expected with the addition of lwt70 HC [62] . This indicates that
the nucleation mechanism with water for plastic/wood-fiber composites is dorninrired by
the moisture in the wood-fibers and that the added chemical blowing agent rarely affects
cell nucleation. A further study is required to clearly identify the nucleation mechanism
in the foam processing with water as a btowing agent. Figures 8 and 9 show the typical
ce1 l morphologies of PS/wood-fi ber and ff IPS/wood-fiber composite foams. respectively,
for compositions A. B. and C.
4.4 Summary and Conclusions
This study examined the possibility of using the moisture in the wood-fiber as a
blowing agent for producing PS/wood-fiber and HIPS/wood-fiber composite foams. For
each plastic. three types of mixtures were prepared and processed: one mixture with HC
distributed using a minerd oil; another mixture with mineral oil but without the
nucleating agent to identify the effect of the mineral oil: and Iastly the plastic/woof-fiber
mixture without any additives.
Based upon the experirnental results, the following conclusions can be drawn:
Even from the oven-dried wood-fibers, a certain amount of moisture is generated in
the processing of plastic/wood-fiber composites. This may be either the absorbed
water or the water of constitution.
The inherent wood-fiber moisture can effectiveiy be used as a blowing agent during
the extrusion foaming of PS/wood-fiber and HIPS/wood-fiber composites.
Depending on the type of plastic matrix used in the composites, an expansion ratio
up to 20 can be achieved in the foarned composites by using moisture in the wood-
fibers as a blowing agent. The obtained ceil density ranged from 1 O' cells/cm3 to
I o6 c e ~ ~ s / c m ~ .
Condensation of water did not cause the PS/wood-fiber composite foams to contract.
However, the HIPS/wood-fiber composite foams contracted significantl y.
The incorporation of 1 wt% HC significantly increased the expansion ratio of the
HIPSIwood-fîber composite foams because of the reduction of the vacuum created
by condensation of water.
5. The use of a small amount of mineral oil enhanced ce11 nucleation for PS/wood-fiber
composite foams. However, the mineral oil did not affect the expansion ratios of
both PS and HIPSIwood-fiber composites.
Force-fed hopper
l lotor Control
--
Figure 4.1 :
t S m + Temperature i - : & Pressure 1 : Control Panel
Experimental Set-up.
Figure 4.2: TGA thermograms for the devolati~ization of wood fibers.
130 140 150 Temperature (C)
(a) PS/wood fi ber composites
O 120 130 140 150 160
Temperature (C)
(b) HiPS/wood fi ber composites
Figure 4.3: Effects of materiai composi1ions and extrusion foaming temperature on the expansion ratio of foamed composites. A: composites with 1 wt HC & 0.5wt % oil B: composites with 0.5 wt% oil C: composites w/o additives
1 O0 150 200
Tempe rature (C)
(a) 3% moisture content.
1 O0 1 50 200
Temperature (C)
(b) 1 1 % moisture content.
Figure 4.4: Effects of temperature variations on the specific volume of the foamed composites.
- I F S C C : I
Figure 4.5: DSC Therrnograms of PS & HIPS
+1% HC
-a- 0% HC
O 2 4 6 8 10 12
Moisture in wood fiber (wt0/0)
Figure 4. 6: iMxcimum achievable volume of wood-fiber composites.
Temperature (C)
(a) PSIwood-fi ber composites
130 140 150 Temperature (C)
(b) HIPSIwood-fiber composites
Figure 4.7: Effects of material compositions and extrusion foaming temperature on the cell-population densities of foamed composites.
a) PS + 30% WF + 1 % HC + mincral oil
- - -
a) HIPS + 20% WF + 1 % HC + m i n c d oil
b) PS + 20% WF + rnincrril oil
Fig. 4-8: SEM micrographs of PS/wood-fibcr composite foarns
b) HIPS + 2 0 4 WF + mineral oit
C ) HIPS + 20% WF
Fig. 4.9: SEM micrographs of HIPS/wood-fibcr composiic foams
Chapter 5
Foaming of PE/Wood-fiber Composites
5.1 Introduction
This chapter describes the processing of pIastic/wood-fiber composites made from
linear low-density polyethyiene (LLDPE) and high-density polyethylene (HDPE), Both
are semi-crystalline polymers widely used for the production of bottles, drums, fuel
tanks. toys, housewares, packaging, etc. LLDPE is mostly extruded and then blown into
films. HDPE is extnided as pipe. sheet. wire and cabie and is also used for coating other
ciitrudates [7 11.
In the previous chapter, the potential for producing PS and HlPS/wood-fiber
composite foams using water as a blowing agent was demonstrated. For polyethylene
(PE). water cannot be utiiized in a similar fashion because of the low stiffness of the
polymer matrix and the resultant contrrtction of foam after the condensation of water
vapor. It is necessary to use an appropriate CBA to obtain acceptable cell structure.
Another factor, which affects PE processing, is its strong hydrophobic nature due to
which the hydrophylic wood-fibers are not well dispersed in the polymer matrix and there
is practically no bonding between the two materials. This necessitates the use of a
coupling agent to promote the molecular bonding between PE and wood-fibers.
5.1.1 Requirements forcouplingagent
Although cellulosic-fiber/polymer composites are known to be superior to the neat
polymers in terms of material cost and stiffness, their stren,oth performance (tende,
flexural. and impact propenies) is generüily lower. The decreased strength is likely a result
of the natural incompatibility of phases dunng the mixing of the hydrophilic cellulosic-
fibers with a high surface tension and the hydrophobic polymer matrix with a low surface
tension [ I ,6,i73. A phase incornpatibility will yield very weak interactions and thus a weak
interface (poor interfacial adhesion) between the fiber and the matnx. Furthemore, strong
fiber- fiber interactions resulting from strong intennolecular hydrogen bonding limit the
dispersion of the fibers in the matrix. In addition to having lower strength, the
thennoplastic/wood-fiber composites possess higher density and are also more brittle than
the untilled therrnoplastics.
The use of coupling or compatibilizing agents is commonly suggested as an
effective solution to the poor strength. These chemical reagents convert the hydrophilic
surface of cellulosic fibers to hydrophobic one. Consequently, the fiber-fiber hydrogen
bonding is reduced and the dispersion of the fibers in the matrix is enhanced. In addition.
the adhesion between polymer and fibers is also improved via mechanisrns such as
diffusion, mechanicd interlocking, and/or formation of chemical bonds between treated
fibers and the polymer matrix. Coupling agents are able to react chernically on both ends
during processing. with the fibers on the one side and the polymer on the other, thus
creating a chemical bridge at the interface. The resultant chemical bonding increases the
ability of the matrix to transfer stress to the fibers, and consequently, the mechanical
properties of polymer/wood-fiber composites are enhanced (20.26-28,721.
By using appropriate coupling agents, polyolefin/cellulosic fiber composites with
a superior strength and a higher modulus compared to the neat polymers have been
produced [1,2,6,57,73]. These composites have higher strength and modulus, and have
been commercialized and are successfully competing with certain plastic and natural
wood. However, their potential for use in many industrial applications has k e n limited
because of their higher density and brittleness compared to neat polyrners or natural
wood. Nonetheless, if these composites can be foamed effectively, the utility of these
materials can be greatly enhanced because the ductiIity, impact strength. and weight can
be al1 irnproved by having a fine-ce11 structure in the composites [7].
For many polyolefins. maleic anhydride of polypropylene (Epolene - 43, Eastman
Chemicals) has proven to be an effective coupling agent in quantities of up to 3 wt% of
wood-fibers 174,751. For concentration of more than 3 wt%, there is no further
improvement in properties. It is typically applied by directly mixing it with the fibers
dong with a small quantity of polymer (usually about 10 wt% of wood-fiber), and then
processing the mixture in a high intensity mixer at about 190°C. The composite so
formed is granulated and used for further processing, such as compounding. etc.
For the experiments under study, the extrusion processing was carried out on an
extruder having an UD ratio of 30 and a mixing section at the end. The mixing capability
of such a configuration is quite good. Thus for initial trials it was decided to forego the
use of higli intensity mixers for dispersing the CBA and CA, as sufficient dispersion was
expected to be achieved during processing in the extruder barre]. Furthemore, the static
mixers in the extrusion system were also expected to aid in the dispersion.
Normally, the 3 wt% CA, Epolene E-43, is applied to the wood-fibers using only
a srnaII amount (typically 10 wt%) of base polymer. However, as the CA was k i n g
mixed dong with a much larger quantity of the polymer, its quantity was doubled (to 6
wt%) from the optimum requirement. It was assumed that the higher concentration would
improve the probability of interaction between the wood-fibers and the CA.
5.1.2 Polyetliylene (PE) foams
PE is the most commonly used thenrioplastic and is available in a variety of
grades suitable for numerous applications. It belongs to the polyolefin family and is a
senii-crystalline polymer. As compared to amorphous polymers, far less information is
auilable for the foam production of fine-celled, semi-crystalline polymers. Most of the
information on microcellular semi-crystalline foarns applies only to batch processing and
very little has been reported on the continuous processing of microcellular semi-
crystalline foams. However, Behravesh 147,481 provides a preliminary study on the
microcellular processing of HDPE in extrusion. The main issue is that semi-crystalline
polymers experience a rapid change in their rheological properties at temperatures close
to their melting (or crystallization) points. This makes it difficult to control the foaming
temperature so as to attain a sound cell structure. and imposes limitations on the foam
processi ng of semi-crystalline pol ymers, and consequent1 y. also on their composites.
There is on published literature about continuous extrusion of pIastic/wood-fiber
composite foams. Matuana [21-24,421 has successfully produced microcellular foamed
plastic/wood-fiber composites in a batch process.
5.1.3 Batch process vs. continuous extrusion
A con tinuous plastidwood-fiber composite foaming process di ffers from the
previously developed batch process 121-341 in many aspects; notably, it is more cost-
effective since less time is required for gas saturation in the polymer. Other main
differences are listed below:
In the batch process. when the sample is heated to initiate foaming after saturation,
heating starts from the skin. This faciiitates the ioss of gas from the outer Iayer during
foaming. In a continuous process, loss of gas can be substantially prevented by
cooling the extrudate surface [47] [also see Sectiorzs 2-3-21.
In batch processing of serni-crystalline polymers/wood-fiber composites, crystalline
regions in the matrix promote non-uniforrn ceIl distribution. In the tightly packed
crystalline regions. no bas is absorbed and higher resistance is offered to ce11 growth.
The gas is absorbed only in the amorphous regions. which also offers lesser resistance
to ccll growth, resulting in a non-uniforrn final foam structure. By contrast. in a
continuous process, the polymer resin is in a molten state with much more uniform
properties. This offers the possibiIity of producing the composite foam with a uniform
cell structure.
a In the batch process, the polymer/wood-fiber composite sample is in rt solid state. It
has the high stiffness necessary to maintain the cell structure. Whereas. in a
continuous process, the polymer resin is in a molten state and is generally too soft to
maintain the cell structure. This issue is critical for the production of semi-crystalline
polymcr composite foams because the polymer rheological properties change rapidly
near its melting temperature.
One of the purposes of this thesis was to investigate the feasibility of producing
wood-fiber composite foams in a continuous process using semi-crystalline FE materials.
Various processes were investigated for their effectiveness in producing the required
foams. and promising configurations have been identified.
The characteristics of a semi-crystalline structure demand much closer control of
temperatures in the neighborhood of crystallization temperatures. Control of the melt
strensth or viscosity by changing the temperature is not easy because of the abrupt
changes in the rheological properties. In the experiments reported here, the temperature
of the nozzle was controlled precisely in srnall steps at temperatures close to the melt or
freezing point.
5.2 Experimentation with Various System Configurations
Efficient and effective moisture removal frorn the wood-fibers is the important
issue in producing plristic/wood-liber composite foams with a fine-cell structure. Efforts
ivere made to develop a process so that this could be achieved in an online process.
Initially, the conventional method of using oven-dried wood-fibers was adopted in a
single-screw extrusion process. This was foilowed by processing in a vented extruder
setup, in which the moisture was removed as a volatile substance through the extruder
vent. Later on. a two-stage process was investipted, wherein rnaster pellets of
plastic/wood-fiber and plastic1CBA were prepared separately and processed in a single
screw extrusion setup after mixing them together. Due to separate processing of wood-
fiber and CBA, the temperature during the wood-fiber master pellet production could be
rriised u p to the final stage processing temperature. In this way, complete moisture
removal could be attained for obtaining a fine-celled foam structure. The CBA master
pellets could be processcd at a lower temperature to prevent its decomposition at this
stage. Finally, a tandem extruder configuration was identified to be an affective system
for moisture removal and achieving a fine cell structure.
5.2.1 Processing of LLDPE/Wood-Fiber Composite Foams Using a Single Screw
Extruder
Materials
The powdered LLDPE Grade LL - 8556 used in this sttidy was supplied by Exxon
Chernical. The wood-fibers were standard softwood (pine) grade 12020, supplied by
American Wood Fibers, as described in Chapter 2. The CBA, Hydrocerol Compound
(HC) was supplied by Boehringer Ingelheim. The coupling agent used for improving the
adhesion between the hydrophobic PE and the hydrophyllic wood-fiber was Epolene E -
43. supplied by ICI. AI1 the materials were used as received.
LLDPE powder and 1 wt% of HC were mixed in a dry blender. This was followed
by the addition of 20 wt% of oven dried wood-fibers and further dry-blended to achieve
homogeneity. In a similar manner, a second batch was also prepared using undricd wood-
fi bers.
Sinole screw experimental setup and procedure
Figure 4.1, shows a schematic of the experimental setup used for processing
LLDPE/wood-fiber composite foams. A nozzle die of 1.02mm (0.040 in.) in diameter and
2.54 mm (0.100 in.) in length was used. However, due to a persistent choking problem,
the diameter of the nozzle was increased to 1-27 mm (0.050 in.) The experirnental
proccdure adopted was the same as in the PS and HIPS processing (see Secrion 4.2). The
tcmperature was maintained at 145OC, 155'C and 205OC in zones 1. 2 and 3 of the
extruder, respectively. The temperature in the diffusion-enhancing device was also
maintained at 205OC. In the heat exchanger, the temperature was reduced to 150°C.
Starting at 1 50°C, the nozzle temperature was gradually reduced down to 120°C and
samples were taken at various nozzle temperatures for density measurement and cell
morphology characterization. The temperatures were carefully controlied to accurately
monitor the foaming behavior at temperatures close to the crystallization point.
Results and discussion
The obtained experimental resuits for LLDPWwood-fiber composite foams using
a single-screw extruder are summarized in Figure 5.1. This figure shows how the nozzle
temperature affects the volume expansion ratio. when dried and undried wood-fibers are
used. Figure 5.2 depicts the typicat cell morphology of the composite foams when dried
and undried wood-fibers are used. According to Figure 5.3, 1 wt% HC can result in an
expansion ratio up to 4.5 times. The TGA result of Figure 4.2 shows that the wood-fibers
used contained about 7 wt% of moisture content, and even oven dried wood-fibers release
3 wt% moisture when heated to the processing temperature of 205°C. Thus. the total
moisture released by undried wood-fibers is 10 wt%, i.e.. 3 wt% + 7 wtyo. If al1 the
moisture is utilized for expansion, an expansion ratio of 12 times can be obtained from 3
wt% moisture and an expansion ratio of 37 times can be obtained from 10 wt% rnoisture
[see Figure 5.31.
For the composite foams made from dried wood-fibers, the maximum obtainable
expansion ratio from the 1 wt% HC and 3 wt% moisture is16 times according to Figure
5.3. However, the maximum expansion ratio obtained was only 3.4 times. There could be
several possible reasons for the low expansion. First, water condenses as the foam
temperature reaches 100°C and is further lowered, creating vacuum within the foam cells.
and due to low stiffness of PE. the cell walls collapse under ambient pressure, as also
explained in Chapter 4. Secondly, some gas couid have been released in the plasticating
stage, due to the high temperature, and escaped back from the hopper into the
atmosphere.
The undried wood-fiber can be considered to have a IO% moisture content. as
described earlier. Therefore, composites made from undried wood-fiber, having 1 wt%
HC and 10 wt% moisture can attain a maximum expansion ratio of 42 times according to
Figure 5.3. However, the maximum expansion ratio obtained was only 8 times. The TGA
rcsults discussed in Chapter 4 imply that, during the extrusion process, a substantial
rimount of the moisture contained in wood-fibers is released as soon as the compounded
mixture enters the hot extruder barrel. As a result, a considerable amount of water vapor
must have escaped through the hopper opening before being trapped in the molten
mixture and pushed further downstream into the extruder. Another possible reason for the
low expansion is the low stiffness of the PE matrix as described above.
The SEM micrographs of the foams [Figure 3.2 (a) & (b)] reveal that they had an
unevenl y distributed foam structure. Even for the dried wood-fiber composite foams, the
structure was non-uniform. This non-uniformity of foam structure can be attributed to the
presence of moisture, which does not dissolve significantly in the polymer matrix, for
both the dried and the undried wood-fiber composites.
In an extrusion process, a fine-celled structure is produced by dissolving a gas,
ei ther injected or chemical 1 y decomposed, into a pol ymer matrix, inducing nucleation and
promoting cell growth. An essential condition for obtaining good ce11 structure, Le., a
large number of uniformly distributed cells, is to obtain a large number of nucleation
sites. The dissolved gas would diffuse into these sites causing the foam to expand
uni for ml y. Inducing a thennodynamic instability through rapid pressure drop across the
nozzle/die can nucleate a large number of sites [ l 1-15]. This is followed by controlling
the expansion phase by properly controlling the melt and skin temperature of the plastic
[47.38].
The solubility of water in PE is very low 1411. The water not dissolved in the
polymer matrix remains in the composite as second phase cavities, which act as ce11
nuclei into which the dissotved gas diffuses. The high surface tension of water prornotes
the formation of larger bubbles and prevents its dispersion into the polymer matrix. This
results in poor mixing of water with the polymer matrix, giving rise to the non-uniformity
of foam ce11 structure. Another reason for non-uniformity of ce11 structure is the irregular
contraction of the foam after expansion outside the die. Therefore, the presence of water
results in undesirable foam structure.
In order to improve the foam structure, it is necessary to remove most of the water
vapors from the molten plastic. The most commonly employed method of drying wood-
fiber is by keeping it in a vacuum oven. for extended periods, at a temperature of about
100°C before usage. This method has a number of disadvantages. It is a time-consuming
batch process, which adds time and cost overheads to an otherwise economical extrusion
process. Secondly, drying at lû@C leaves behind about 3 wt% water of constitution and
adsorbed water. which is released at the processing temperature of 20S°C, and causes
deterioration in ce11 structure. It also necessitates specid handling procedures to prevent
contact between the wood-fiber and moist air. Therefore, the development of an online
process for removing moisture from the wood fiber would be of enormous utility in
plastic/wood-fi ber composite manufacturing.
A vented extruder is frequently used to purge out the volatile materials from the
polymers during extrusion [76]. Utilizing this technique to get rid of moisture would
result in many advantages, the chief being the conversion of a batch drying process to a
continuous online moisture removal process. Based upon this principle, a number of trials
Lvere carried out with a vented extruder and these are described in Section 5.2.3.
5.2.2 Experitnents of HDPE/Wood-Fiber Conrposite Foatrrs Usittg a Sirrgle-Screw
Extruder
iMaterial
HDPE Grade 58A from Novacor was used as the base polymer for the
composites. The wood-fiber, the CBA and the CA used were the sarne as described in
section 5.2.1. The materials were used as received.
Blendino
Three compositions were prepared using 20 wt% wood-fiber, 6% CA by weight
of wood-fiber and different concentrations of HC, Le.. O%, 1 % and 5%. Initially. HDPE,
HC and CA were dry blended thoroughly. Then wood-fiber was added and blended again
to achieve homogeneity.
Expcrimental setup and procedure
The mixtures were dry blended and processed in a single screw extruder as
described in the previous section. The temperature was maintained at 155"C, 160°C and
205°C in zones 1, 2 and 3 of the extruder respectively. The temperature in the diffusion-
enhancing device was also maintained rit 205'C. In the heat exchanger. the temperature
was reduced !O 150°C. Starting at 150°C, the nozzle temperature was gradually reduced
down to 120°C and samples were taken at various nozzle temperatures for density
meauremen t and ce1 l morphology characterization.
Results and discussion
The results of these experirnents are shown in Figure 5.4. For the formuIations
with 0% and 1 % HC, the maximum expansion ratio obtained was less than 2 times. This
indicrites that nearly al1 the gas in the mixture escaped to atmosphere through the
extrudate skin, However, the 5% HC formulation foamed substantially and an expansion
ratio of almost 10 times was obtained. However, the SEM in Figure 5.5 reveals that the
ce11 structure is very irregular with the presence of large bubbles as in the case of
LLDPE/wood-fiber composite foams.
Figure 5.3 shows that the maximum possible expansion ratio for ri wood-fiber
composite foam containing O, 1 and 570 HC is 37, 42 and 60 times, respectivety, for a
moisture content of 10 wt% by weight of wood-fiber. It seems that HDPE is more
intolcrant of water vapor than LLDPE, and only in the presence of a signiticant amount
of CO?, i t is able to maintain its expanded cell structure. Significantly there was no
difference in the expansion ratio of 0% HC vs. 170 HC. In Chapter 2. we found that for
the softer HIPS, the presence of CO2 released from even 1% HC considerably improved
the expansion ratio. It was believed that when the rnoisture condensed at l m C creating
vacuum, the partial pressure of the CO2 present in the cell was sufficient to resist the cell
collüpse. However, this phenornenon was not observed in the case of HDPE. The
probable reason is that the stiffness of HDPE at the elevated temperature is much lower
than that of HIPS. The partial pressure of CO2 released by 1 wt% HC was not enough to
prevent ceIl collüpse in HDPE, due to the vacuum crerited by the water condensation at
100°C. Another possible reason is that due to higher diffusivity. the amount of gas lost in
HDPE processing is considerably higher than in HIPS [48.68].
Only when the HC amount was increased to S%, did we obtain significant
expansion (10 times). However, the cell structure was still very non-uniforrn, indicating
that the cell formation mechanism was not the one described in Section 5.2.1 for
producing a fine-celled structure. The presence of moisture. which is almost non-soluble
in HDPE [4 11, was the probable cause of this non-uniformity.
It is essential to remove ail the water vapor from the molten mixture to obtain a
good ceII structure. To achieve this goal, a number of system designs were considered
and experimentall y evaluated.
5.2.3 Processing of LLDPEn-Yood-Fiber Composite Foams Using a Vented Extruder
and a Gear Pump
Materials and blending
Powdered LLDPE, 20 wt% wood-fibers and 6 wt% CA by weight of wood-fiber
were blended with 1 wt%, 2 wt% and 3 wt% HC as described previously. Initially,
LLDPE, HC, and C A were dry blended thoroughly. Then, wood-fiber was added and
biended again to achieve homogeneity.
Experi mental setup and processin g
A schematic of the experimental setup is given in Figure 5.6. The dry btended
mixtures were fed into the hopper and the temperature in the second heating zone was
rriised to 150°C. This temperature was chosen so that the CBA in the melt was not
decomposed during melting. but most of the moisture in it wouid be drivsn out through
the vent after rrielting. However, durin3 processing, the molten material started coming
out of the vent because the rate of inflow was higher than the rate of outflow to the die. Ln
spite of many attempts, the loss of material through the vent proved difficult to control. A
screw pump was incorporated into the system on the assumption, that the suction head
oenerated by the gear pump would increase the flow rate through the extruder, thereby - decreasing the material Ioss from the vent. The gear pump failed to rcduce the material
loss.
To address the problem mentioned above, the process was redesigned. A new
decomposi tioddiffusion section was constructed and added after the gear pump [Figure
5-71. For the new process, the temperature from the vent up to and including the gear
pump was kept under 160°C to prevent CBA decomposition. After the gear pump. the
temperature was increased to 205OC in the decomposition/diffusion section. This section
was also provided with a static mixer in order to improve the temperature homogeneity
and effective decomposition. The extrudate was then cooled down to 150°C in the
cooling section and finally extruded throu~h the nozzle die.
However, the gear pump again failed to reduce the material loss through the vent.
There are two possible hypotheses for this. First. the gear pump was acting on the
extruder from the suction side. hence the maximum pressure effect it could possibly
oenerate was -14.7 psi (absoIute vacuum). Second, due to the low processing - temperatures (less than 160°C) up to the gear pump, the viscosity of the melt was higher.
The higher viscosity fluid requires more energy to transport i t through the barrel. This
raised the pressure within the barrel, resulting in materia1 loss through the vent.
The results of thesc experiments are shown in Figure 5.8. For 1 wt% HC the
maximum expansion ratio obtained was about 3 times and the processing window for
obtaining more than 1.5 times expansion was quite narrow, berween 125°C and 127°C.
Surprisin,aly on increasing the concentration of HC io 2 wt% and 3 wt%. the expansion
ratio dropped down to about 1.5 times. Increasing the HC amount did not have any effect
on the expansion ratio. and on the contrary, it reduced the expansion ratio. It is speculated
that the increased residual constituents of the HC modified the melt characteristics of the
plastic and promoted gas loss in the extruded foam.
5.2.4 Processing of LLDPE/Wood- Fiber Composite Foams Using a Masfer Pellet
The difficulty of controlling the loss of material through the devolatilizing vent
forced us to search for other solutions. One possible solution was to redesign the screw
with a different pitch after the vent opening, so that the back-pressure did not reach the
vent. However, this was an expensive solution in terms of both the cost and the time
invol ved.
Another possible solution was to process the composite foams in two stages. In
the first stage, master pellets of plastic and wood-fiber, and plastic and CBA were
prepared. These pellets were then mixed in appropriate proportions and processed in the
second stage to produce the composite foarns. The advantage of this method is that when
pIastic/wood-fiber master pellets are prepared, most of the rnoisture is driven out from the
extrudate. at the die exit. Secondly, as the wood-fibers are well wetted by the plastic in
the moIten state, they could not reabsorb significant amounts of moisture upon being
cooled down and special handling and storing procedures are not required for preventinz
moisture absorption. In order to promote good wetting of polymer ont0 the wood-fibers.
an appropriate coupling agent should be used. Another benefit of this process is that the
CB A is processed separate l y. Therefore, the processing temperature cou Id be main tained
as low as the equipment couId handle. This eliminates the problem of early CBA decomp
osition. This process also has the advrtntage that the force-feeding hopper was only
required on the compounder used for preparing the plastic/wood-fiber master pellets.
Once pelletized, the materials could easily be gravity-fed in the final stage hopper.
Materials and blendino
50% plastic, 50% wood-fibers and 6 wt% CA by weight of wood-fiber were dry
blended and processed in a single screw extruder to make wood-fiber master pellets. The
temperature in the extruder barre1 was raised up to 165T for easier processing. The
estrudate was air-cooled and then fed into a pelletizer (Brabender Lab PeIletizer: Type
12-72-00) to make pellets. For making CBA master pellets. 1.67 wt% of CBA was dry
blended with powdered plastic and processed in extrusion. The temperature throughout
the extruder barre1 was maintained below 150°C to prevent CBA decomposition. The
extrudate was again air cooled and fed into a pelletizer. It should be noted that a
commercial ,arade of CBA in the form of pellets with a plastic c h e r could also be used
as the CBA master pellets. Finally, two parts of wood master pellets and three parts of
CBA master pellets were mixed in a dry tumbler to get the desired ratio of the
constituents.
Foamino experiments and discussion
The mixed master pellets of wood-fiber and CBA were fed into the hopper of the
extnider for final stage processing. The maximum temperature of the melt was raised to
205°C for compiete decomposition of the CBA and after being cooled down to 150°C in
the cooling section, it was extruded through the nozzle die at various temperatures.
Although the processing conditions were very stable, the maximum expansion
ratio was only 2.5. This expansion was obtained in the transient conditions before the
flow cornpletely stopped due to the polymer freezing in the nozzle. Othenvise, the
expansion ratio was always less than 1.5.
52.5 Experirnents of HDPE/IVood-Fiber Composite Foams Using a Tandem
Extruder Setup
Use of the master pellet scheme described in the previous section seems to be an
effective approach, although, possibly due to the material properties, it did not produce
good results with LLDPE composites. However, this scheme has the disadvantage of
introducing the additional processing stage of pelletizing, in addition to two-stage
processing. Furthermore, this scheme involves additional handling and processing
overheads. Another possible method for affective removal of moisture is the utilization of
two singie-screws in a tandem configuration. The output of the first extruder is fed into
the inlet of the second extruder at which point the moisture is effectively removed due to
the devolatilization at the high temperature. Promising results were obtained during the
initial investigation described below.
Materia1
HDPE Grade 58A from Novacor was used as the base polymer for the
composites. The wood-fiber. the CBA and the CA used were the same as described in
section 5.2.1. The materials were used as received.
Blendinp
Three compositions were prepared using 20 wt% wood-fiber, 6% CA by weight
of wood-fiber and different concentrations of HC, i.e., O%, 1% and 5%. initially. HDPE.
HC and CA were dry blended thoroughly. Then wood-fibers were added and blended
rigain to achieve homogeneity.
Experimental setup and procedure
A schematic of the tandem extrusion system is shown in Figure 5.1 1. The
mixtures were dry blended and fed into the first single-screw extruder, as described in the
previous section. The temperature in this extmder was maintained at 155°C throughout
the system, to prevent the decomposition of CBA and the degradation of wood-fïber. The
temperatures in the second tandem extruder were maintained at 155°C and 165°C in
zones 1 and 2, respectively. The temperature in zone 3 of the barre1 and in the diffusion-
cnhancing device was maintained at 205°C to ensure complete decomposition of the
CBA. In the heat exchanger, the temperature was reduced to 150°C. Starting at 150°C. the
nozzle temperature was gradually reduced to 130°C and samples were taken nt various
nozzle temperatures for density measurement and ceIl morphology characterization.
Results and discussion
The results of these experiments are shown in Figure 5.9. The removal of
moisture results in the eIevation of the lowest working nozzle temperature. In the
presence of rnoisture in wood-fiber, the lowest working temperature for the nozzle was
133°C. according to Figure 5.5. With the devoiatilization of water. the nozzle temperature
could only be lowered to 139OC without blocking the nozzle. This phenomenon can be
attributed to a lower effective viscosity, due to the presence of a greater amount of
gaseous content in the non-devolatiIized case. For the formulation with 1% HC, the
maximum expansion ratio obtained was five-fold. The 5% HC formulation again foamed
substantially and an expansion ratio of almost 9 times was obtained. The SEM in Figure
5.10 reveals that the ce11 structure is very reguhr when compared to the non-devolatilized
case. The Iargest cells were smaller than 150 mm and the distribution of cell size was not
very large.
This experiment suggests that the rtssumptions. regarding the utility of a tandem
extrusion sctup for the production of fine-celled plasticlwood-fiber composite foams. are
correct. The removal of moisture significantly improved the ce11 size distribution and
prevented ce11 coarsening.
5.3 SUMMARY AND CONCLUSIONS
A series of experiments was carried out to examine the possibility of produçing
LLDPE/wood-fiber and HDPE/wood-fiber composite foams using a CBA. Based upon
the experimental results, the following conclusions can be drawn:
The maximum expansion obtainable for LLDPE/wood-fiber composite was 8 fold
without using any additive or CBA. The wood-fibers used were not dried. The ceil
structure of these foams was not uniform.
By using oven-dried wood-fiber and CBA content of 1 '3. the expansion ratio was
reduced to 3.4 times. The ce11 density again was not uniform.
The foam-processing window for LLDPE/wood-fiber composite is very narrow and
it is very difficult to maintain stable flow at tower temperatures.
HC is not a suitable blowing agent for the grade of LLDPE used.
A promising processin3 scheme of separateIy making master pellets of wood-fiber
and CBA was identified. However. it could not be applied to HDPE composites
because of equipment limitations.
An expansion ratio of 10 was obtained for HDPE/wood-fiber composites with f%
HC, but the ceIl structure was grossly unacceptable.
A tandem extruder process for production of foam was successfully identified. A
high volume expansion ratio of up to 9 was obtained with a much improved ceIl
stmcture.
Complete moisture removal is essential for obtaining a fine-ceIled structure in
plastic/wood-fi ber composite foams.
Fig 5 . I
122 1 24 126 128
Temperature (C)
Effect of nozzle temperature on the expansion ratio of LLDPE/wood-fiber composite foams processed with 1 wt% HC. Series A represents composites produced with undried wood-fibers, and series B represents composites produced with dried wood-fibers.
Fig 5.2: SEM micrographs of a) LLDPE/wood-fiber composite foams (a) using undried and (b) dried wood-fibers
Moisture in Wood-Fiber
Figure 5.3: Theoretical expansion ratio for a composite foam having 20 wt% wood-fi ber.
140 145
Temperature (C)
Figure 5.4: Volume expansion behavior of HDPE/wood-fiber composite foams using HC as aCBA
Figure 5.5: SEM microgragh of HDPE/wood-fi ber composite foam wi th ten-foid expansion.
126 127 128
Temperature (C)
Figure 5.8: Volume expansion behavior of LLDPUwood-fiber composites while using a venting extruder with a gear pump.
140 145
Temperature (C)
Figure 5.9: Volume expansion behavior of HDPE/wood-fiber composite foams in a tandem extrusion setup.
Figure 5.10: SEM microgragh of HDPWwood-fiber composite foam from a devolatilized tandem extrusion system with nine-fold expansion.
Figure 5. i 1 : Schematic of a devolatilization tandem extrusion system
Chapter 6
Summary, Conclusions and Future Work
6.1 Summary
This study was conducted to examine the feasibility of producing fine-cetled
plastic/wood-fiber composite foams. Although, it is weli known that physical blowing
agents are wetl suited for obtaining a fine or even microcellular structure, CBAs are
predominantly used in the industry. Therefore, as an evolutionary step, it was decided to
use CBAs for this study. Moisture is inherently present in wood-fibers and causes
deterioration in the ceIl structure. Thus, rnoisture removal is another important issue in
the production of fine-celled plastic/wood-fiber composite foams.
There are a number of applications, such as packaging and mild insulation where
the cell structure is not so crucial. For these applications, it was decided to explore the
feasibility of using the inherent water present in the wood-fiber as a blowing agent. This
would lead to substantial cost savings both in terms of the cost of filler as well as the cost
of CBA. As described in Chapter 4, the initial investigations yielded quite promising
results.
A number of extrusion configurations were evaluated for the production of fine-
celled plastidwood-fiber composite foams using a CBA. Two systems for producing
fine-celled plastic/wood-fiber composite foams have been identified. The aim was to
produce these foams with a high cell-population density (greater than 105/crn3), a srnall
ce11 size (lesser than 0.5 mm) and a decent volume expansion ratio (on the order of 10
fold).
95
The first system was a two-stage process employing a single-screw extrusion
system for first producing plasticlwood-fiber and plasticlCBA master pellets, and then
processing an appropriate mixture of these pellets to produce composite foams. However
the CBA, Hydrocerol Compound proved to be not suitable for LLDPE, and equipmenr
limitations prevented the processing of HDPE.
A devolatilization tandem extrusion system was designed so that the output of one
extruder was fed into the second extruder, at which point the moisture was devolatilized
through an open vent. The temperature in the second extruder was raised high enough to
decompose al1 the CBA. Critical experiments were performed to check the functionality
of the system. The plasticlwood-fiber composite produced on this system had a much
improved ceIl structure than was previously achieved. The obtained experimental results
indicated that the tandem system is capable of producing a much better ceIl stmcture in
the plastic/wood-fiber composite foams and higher volume expansion ratios.
6.2 Conclusions
Based on the work presented in this thesis. the following conclusions can be
drawn :
1 . The feasibility of using inherent water present in the wood-fiber as a blowing
agent was successfully explored. Up to 20 times expansion was achieved in PS and
HIPSlwood-fiber composite foarns. The utilization of a nucleating agent HC significantly
improved the cell structure of the PSIwood-fiber composites. On the other hand, by using
HC in HIPS/wood-fiber composites, the expansion ratio was increased from nine-fold to
twenty-fold.
96
2. The feasibility of online removai of moisture was studied. This would
considerably enhance the potentid of using wood-fiber in large-scale production
processes.
3. A vented extruder, although successful in removing the moisture, proved
impractical due to excessive loss of materiai from the vent.
4. A two stage process was investigated. Master pellets of plastic/wood-fiber and
pIutic1CBA were produced in the initial stage. The pellets were then mixed in an
appropriate ratio and processed in the second stage. Due to equipment limitations, this
process could only be used for LLDPWwood-fiber composite foams, which did not foarn
well, probably due to incompatibility of the blowing agent with the base matrix.
HDPE/wood-fiber composites could not be processed, at the appropriate low temperature,
on this system due to the torque limitations of the system.
5. The devolatilization tandem extrusion system showed promising results in the
initial experiments. An expansion ratio of nine was obtained when 5 wt% HC was used
for producing HDPEIwood-fiber composite foams. The cell size distribution obtained was
quite narrow and varied around 150 p.m. Although, the sarne amount of expansion was
also obtained from a single-extruder processing with undried wood-fiber, the cell
structure was extremely coarse with the larger celIs being greater than I mm.
6.3 Future Work
The fotlowing suggestions are made for the future direction of the research work
in order to obtain fine-celled plastic/wood-fiber composite foarns:
1 . Of the total gas released by the blowing agent Hydrocerol Compound, 50 wt% is
97
water vapor. As mentioned earlier, water vapor causes deterioration in the ce11 structure.
Therefore, a CBA needs to be identified which only releases an inert gas such as CO?.
2. A full parametric search should be carried out to determine the proper processing
conditions for the production of fine-celled HDPE/wood-fiber composite foams.
3. The CBA concentration should be varied to determine the optimum quantity to be
used, so that gas loss to the atmosphere is reduced.
4. Al1 the experiments were performed using only 20 wt% wood-fiber. Different
concentrations of wood-fiber should be used to determine the effect on the processing
conditions and on ce11 morphology.
5 . Finally, different materials should be proçessed to determine the effect of material
on the structure and properties of plastic/wood-fiber composite foams.
References
J.J. Balatinecz and R.T. Woodhams, "Wood-Plastic Composites: Doing more with less," J. Forestry, 9 1 ( 1 1 ): 22 ( 1993).
HChtourou, B. Riedl and A. Ait-Kadi,"Reinforcement of Recycled Polyolefins with Wood- Fi bers," J. of Reinforced Plastics and Composites, vol. II-April 1992.
R. G. Raj, B. V. Kokta, G. Groleau & C. Daneault, "Use of wood fiber as a filler in pol yeth ylene: studies on mechanicd properties", Plastics and Rubber Processing and Applications Vol. 1 1, No.4, 1989
W. Storck, "Reinforced plastics use to pick up momenturn," Citem. Eng. News, p. 15, VOL 65 No.44 (Nov. 2) (1987).
R. Eller, P la t . World, 32-74 (1974)
J.A. Youngquist and R.M. Rowell, In Froceedings, 23rd International Particleboard/Composite Materials Symposium. T.M. Maloney, ed., Was. State Univ., Pullman, p. 141 (1990).
L.M. Matuana, J.J. Balatinecz, and C.B. Park, Polym. Eng. Sc., 38,765 (1998).
Sherwood Technologies, Inc. from thei: internet site http://www.foamandform.com/throne@ foamandforrn.com
D. Suwanda, J. Chan, V. Zhou, and J. Lutoslawski, "Product Design and Performance Issues for Domestic and Offshore Markets, " 4th International Conference on Woodfibre- Plastic Composites, Toronto, Ontario, June 1 998.
J. Martini, F.A. Waldman, and N.P. Suh, "Microcellular Closed CeIl Foams and Their Method of Manufacture," U.S. Patent 4,473,665, ( 1984).
C.B. Park, and N.P. Suh, "Rapid PolymedGas Solution Formation for Continuous Processing of Microcellular Plastics," ASME Trans.. J. Manuf: Sci. Eng., Vol. 1 18, pp. 639- 645 (1 996).
C.B. Park, and N P . Suh, "Filamentary Extrusion of Microcellular Polymers Using a Rapid Decompressive Element," Polym. Eng. Sci., Vol. 36, No. 1, pp. 34-48 (1996).
C.P. Park, D.F. Baldwin, and N.P. Suh, "Formation and Application of a folymer/Gas Mixture in continuous Processing of Microcellular Polymers," ASME, Cellular and Microcellular Materials, MD-Vol. 53, pp. 109- 124 ( 1994).
14 C.B. Park, Baldwin, and NP. Suh, "Effect of the Pressure Drop Rate on Ce11 Nucleation in Continuous Processing of Microcellular Polyrners," Polym. Eng. Sci., Vol. 35, No. 5, pp. 432-440 ( 1995).
15 D.F. Baldwin, C.B. Park, and N.P. Suh, "An Extrusion System for the Processing of Microcellular Polyrner Sheets: Shaping and Ce11 Growth Control," Polym. Eng. Sei., Vol. 36, No. 10, pp. 1425- 1435 (1996).
16 R.G. Raj and B.V. Kokta, "Improving the Mechanical Properties of HDPE-Wood Fiber Composites with Additives/ Coupling Agents," p. 1883, SP E ANTEC '9 1 .
17 LA. Youngquist, "Unlikely Partners? The Marriage of Wood and Nonwood Materials," Forest Prodrtcts J., . Vol. 45, No. 10, p.25-30 ( 1 995).
18 W.V. Titow and B.J. Lanharn, "Reinforced Thermoplastics", Applied Science Priblishers, London ( 1975).
19 J. Van Nostrand Reinhold (Ed), "Plastics Additives and Modifiers Handbook", New York, ( 1 992).
20 S.M. Yushkova, A.A. Tager, SN. Potepalova, V.B. Mozzhukhin, and S.K. Bogatkinn, Plasr. Massy. 12, 38(1987)
2 1 L. Matuana-Malanda, C.B. Park, and J.J. Balatinecz, "Characterization of Microcellular Foamed PVC/Cellulosic-Fiber Composites," Journal of Cellular Plastics, Vol. 32, No. 5, pp. 449-469, 1996.
22 L.M. Matuana, C.B. Park, and J.J. Balatinecz, "Processing and Ce11 Morphology Relationships for Microcellular Foarned PVC/Wood-Fiber Composites, " Polymer Engineering and Science, Vol. 37, No. 7, pp. 1 137- 1 147, 1997.
23 L.M. Matuana, C.B. Park, and J.J. Balatinecz, "Structures and Mechanical Properties of Microcellular Foamed Polyvinyl Chloride," Cellular Polymers, Vol. 1 7, No. 1 , pp. 1 - 16, 1998.
34 L.M. Matuana, C.B. Park, and J.J. Balatinecz, "Cell Morphology and Property Relationships of Microcellular Foamed PVCAVood-Fiber Composites, " Polyrer Engineering and Science, Vol. 38, No. 1 1, pp. 1862- 1872, 1998.
25 D. Maldas, B.V. Kokta, and C. Daneault, J. Vinyl Technol., 1 1 (Z), 90 (1989).
26 B.V. Kokta, D. Maldas, C. Daneault, and P. Beland, "Composites of Polyvinyl Chloride- Wood-Fibers. 1: Effect of isocyanate as a Bonding Agent," Polym, Plclsr. Technol. Eng., 29, 87 ( 1990).
27 B.V. Kokta, Polymer News, 13, 33 1 ( 1 988).
D. Maidas and B.V. Kokta,Polym. J., 23, (10) 1163 (1991)
B.V. Kokta, D. Maldas, C. Daneault, and P. Beland, J. Vinyl. Technol., 12 (3), 146 (1 990)
L A . Goettler, "The Extrusion and Performance of Plasticized Poly(viny1 Chloride) Hose Reinforced with Short Cellulose Fibres," Polym. Comp., 4 (4), 249 (1983)
D. Klempner and K.C. Frisch, Handbook of Polymeric Foams and Foam Technology, N.Y. (199 1).
P.E. Botillier, Br. Patent 1,184,688 ( 1969).
F.A. S hutov, Integral/ Structural Pol ymer Foams, Springer-Verlag (1 986)
S.T. Lee, N.S. Ramesh, and C.A. Campbell, "Temperature Effects on Thennopiastic Foam Sheet Formation," SPE ANTEC, Vol. 39, pp. 3033-3036 (1993).
J. Throne, "Science and Technology of Polymer Process," Suh, N.P. and Sung N. ed., MIT Press, Cambridge, pp. 77- 13 1 ( 1979).
Frich, K.C., and Saunders, J.H., Plastic Foams, Part U, Marcel Dekker, New York (1 973).
R.A. Gorski, R.B. Ramsey, and K.T. Dishart, "Physicai Properties of Blowing Agent Polymer System-1. solubility of Fluorocarbon Blowing Agents in Thennoplastic resins," J. Cell. Plrst., Vol. 22, N o . 1. pp. 2 1-52 ( 1986).
K.C. Frich, and J.H. Saunders, Plastic Foams, Part 1, Marcel Dekker, New York (1972).
F.J. Dwyer, L.M. Zwolinski, and K.M. Thrun, "Extruding Thermoplastic Foams With a Non-CFC Blowing Agent," Plus. Eng., May, pp. 29-32 (1990).
J. Martini, F.A. Waldman, and N.P- Suh, "The Production and Analysis of Microcellular Therrnoplastic Foams." SPE ANTEC Tech. Papers, 28,674 (1982).
Van Krevelen, D.W., "Properties of Polymers," Elsevier Scientific Publishers Company ( I W O ) .
L.M. Matuana, Ph.D. Thesis, University of Toronto, 1997.
Kumar, V.P. and Schirrner, H.G., "Semi-Continuous Production of Solid State PET Foams," SPE ANTEC Tech. Papers, Vol. 4 1 , pp. 2 1 89-2 1 92 ( 1995).
Colton, J.S., and Suh, N.P., "Nucleation of Microcellular Theory and Practice, " Polym. Eng. Sci., Vol. 27, No. 7, PD. 500-503 (1987).
Baldwin, D.F., Suh, NP., and Shimbo, M., "Gas Dissolution and Crystallization in MicrocelluIar Thennoplastic Polyesters," in: Cellular Polymers, MD-Vol. 38, Kumar, V. and Advani, S.G., ed., ASME, New York, pp. 109-1 28 (1992).
A.H. Behravesh, C.B. Park, and R.D. Venter, "Effective Suppression of Ce11 Coalescence During Shaping in the Extrusion of Microcellular HiPS Foams, " 212th Narional ACS Meeting, Polymer Preprints, Vol. 37, No. 2, pp. 767-768 (1996).
A.H. Behravesh, Ph.D. Thesis, University of Toronto, 1998.
A.H. Behravesh, C.B. Park, and R.D. Venter, "Challenge to the Production of Low-Density, Fine-Cell HDPE Foams Using C02," Cellular Polymers, Vol. 17, No. 4, pp. 000-000, 1998.
A.H. Behravesh, C.B. Park, and R.D. Venter. "Extnision of Low-Density Microcellular HIPS Foams Using C02," MD-Vol. 76, Cellular and Microcellular Materials, ASME ( 1996).
D.I. Collias, D.G. Baird, and R.J.M. Borggreve, Polymer, 25 (18), 3978 (1994).
B.S. Westerlind and J.C. Berg,Patent, U.S. Patent, No. 4,475,789, ( 1984).
A. Pabedinskas, D. Suwanda, J. Yang, V. Zhou, J.J. Balatinecz, R.T. Woodharns, Canadian Association for Composite Structures and Materials, CANCOM'93, Second Canadian Internat ional Composites Coference and Exhibition, Ottawa, Ontario
C.B. Park,"The Role of PolymerIGas Solutions in Continuous Processing of Microcellular Polymer," Ph-D. Thesis, Massachusetts Institute of Technology, Cambridge, MA (1993).
Product Catalogue, The Flow and LeveI Handbook, Vol. 28, Omega Engineering, Inc. ( 1 992).
F.A. Shutov, in Handbook of Polymeric Foams and Foam Technology, Chap. 17, D. KIempner and K. C. Frisch, eds., Hanser, New York (199 1).
J. Meyke, Foam Conference '96, 179 ( 1 996).
R.T. Woodhams, G. Thomas, and D.K. Rodgers, "Wood-Fibers as Reinforcing Fillers for Polyolefins," Polym. Eng. Sci., 24, 1 166 (1984).
A.W. Adamson, Physical Chemistry of Surfaces, 5th ed., John Wiley & Sons, New York ( 1 990)
L.M. Matuana, R.T. Woodhams, J.J. Balatinecz, and C.B. Park, Polyrn. Compos., 19,446 ( 1 998).
60 M. Kazayawoko, J.J. Balatinecz, and C. Law, Inr. J. Polym. Mat., 37, 237 (1997).
R.T. Woodhams, "A study of the Mechanical Properties of Wood Fibreffolystyrene Composites," Unpublished Report, University of Toronto (1 992).
A.H. Behravesh, C.B. Park, L.K. Cheung and R.D. Venter, J. Vinyl Add. Tech., 2,349 ( 1 996).
J.H. Saunders, in Handbook of Polymeric Foams and Foarn Technology, Chap. 2, D. Klernpner and K. C. Frisch, eds., Hanser, New York (1 99 1).
D.F. Baldwin, C.B. Park, and N.P. Suh, Polym. Eng. Sci., 38, 674 (1998).
Franc, Personal Communication, Boehringer Ingelheirn (1 998).
N.S. Ramesh, D.H. Rasmussen, and G.A. Campbell, "Heterogeneous Nucleation of Microcellular Foarns Assisted ny the Survival of Microvoids in Polymers Containing Low Gas Transition Particles. Part II: Expeximental Results and Discussion
W.C. Reynolds and H.C. Perkins, Engineering Thermodynamics, 2nd Ed., McGraw-Hill Publishing Company (1 977).
C.B. Park, A.H. Behravesh, and R.D. Venter, Polynl. Eng. Sci., 38 (1 1). 000 (1998).
L.M. Matuana, C.B. Park, and J.J. Baiatinecz, "Effect of Cell Morphology on the Properties of Microcellular Foarned PVCWood-Fiber Composites," In: Cellular and Microcellirlar Materials, Kumar, V. and Sealer, KA., eds, ASME, N.Y., pp
NPAC, International Therrnodynarnic Tables of Fluid State 3-Carbon Dioxide, Pergamon Press, New York (1 973).
Maine, F., "An Introduction to the Canadian World of Plastics," Frank Maine Consulting Limited (1997).
S. Dong, S. Spieha, and H.P. Schreiber, "Mechanical Properties of Corona Modified CelluIose/PoIyethyiene Composites." Polynr. Eng. Sci., 33 (6): p.343 ( 1993)
R.G. Raj, B.V. Kokta, D. Maldas, and C. Daneault, J. Appl. Polyrn. Sci.,37, 1089 (1989).
1-P-Schneider, ans A.C. Karmaker, "Composites From Jute- and Kenaf- Reinforced Polypropylene," SPE, ANTEC '95
C.A. Grzejka, "RecycIed HDPE and Recycled Newsprirzt Bonded Togather to Create Structural Wood Substitute," SPE, ANTEC '95.
76 R.J. Pi balak, "Pol ymer Devolatil ization", Marcel Dekker Inc., ( 1996)