LLC7220Dynadimmer SELV

General Description

The Dynadimmer SELV is a lamp driver control device that enables high-energy savings with low installation efforts in a variety of applications. The small stand-alone luminaire-based device can drive a 1-10V electronic driver to facilitate on-demand light levels. The Dynadimmer SELV does not require an additional switching wire. The Dynadimmer SELV dimming schedule is flexible up to five dimming levels and five time periods. Easy-to-operate software and programming equipment enable municipal councils to re-program the dim times and dim levels as and when they wish.

The Dynadimmer family consists of:• LLC7210Dynadimmer• LLC7220DynadimmerSELV• KIT7210DynadimmerProgrammingKit• LCC7210/00DynadimmerUSBPCCable.

The Dynadimmer SELV is specifically designed for LED luminaires and has a galvanic separation between the 1-10V output and mains input.

Applications

Each Dynadimmer SELV can control a driver-lamp combination in a stand-alonemanner.Itisdesignedforuseinresidential,streetandroadlightingapplications,includingparkinglots,ports,trainstationsandindustrial complexes. The design of the Dynadimmer SELV is optimized for mounting in a luminaire.ThePhilipsDynadimmerSELVisdesignedandreleasedtointeractwithPhilips1-10Vgearandiscompatiblewithdimmabledriverswithastandard 1-10V interface.

1/4

109.5

99.5

3044

.5

M8

82

4.2

33.5

Dimensions in mm

05

LLC7220Dynadimmer SELV

2/4

Benefits and advantages

The major benefits and advantages of using the Dynadimmer SELV solution are:• Energysavingsthroughdimming• Reducedlightnuisance• Verysmallsize,fitsinsidealmostanyluminaire• Softwareprovidesaforecastofenergysavings• Easy-to-usesoftware

General operation

The dimming schedule is created in the Dynadimmer software. This easy-to-usesoftwareenablestheusertoobtainnotonlyaquickdimmingshape configuration but also a forecast of energy savings. The dimming schedulemaybefine-tunedand,bymeansoftheProgrammerortheUSBPCcable,programmedintoeachindividualDynadimmerSELV.

TheDynadimmerSELVhasnointernalclockandusesamidnightpoint calculation to determine the absolute time. The midnight point is calculated as the middle point between switch on and switch off. Dependingontheselectedcountry,atimeisallocatedtothismidnightpoint.TheDynadimmerSELVneedstwonightstochecktheconsistencyof the duration of both nights. The dimming schedule will start to operate on the third night after installation.

6:0015:00

0%

20%

40%

60%

80%

100%

12:00 14:00 16:00 18:00 20:00 22:00 00:00 2:00 4:00 6:00 8:00 10:00 12:0023:00 5:00

D1

D2

D3

T1 T2 T3 T4 T5D4

D5

Dimming shape example

Mounting information

TheDynadimmerSELVisdesignedtobebuiltintoaluminaire,abox,anenclosureorthelikeandisnotintendedtobemountedoutsidealuminaire,etc.withoutspecialprecautions.Thecontrolgearcompartmentin the base of a road lighting pole is considered to be an enclosure.The Dynadimmer SELV can therefore be mounted in any position if theenclosureisIP43orhigher.WiringhastobeinaccordancewithEN60598.

tc max. 75°C

Dynadimmer SELVLLC7220/009137 003 38503Un: 220-240V~ 50/60Hzta: -40...+55°C tc: 75°C

9±0.5

0.5...1.5 mm2

Housing provides insulation for class IIMade in EUwww.philips.com

tc

SELV output

1-10V

+–

NN

LL

05

Tc point Dynadimmer SELV

LLC7220Dynadimmer SELV

3/4

Dynadimmer software

The dimming schedule is created in the Dynadimmer software. The Dynadimmer software can be downloaded free of charge from the Philipswebsiteatwww.philips.com/dynadimmer.Thereareseveralvariables that allow the configuration of a dimming schedule. The light levels D1 to D5 can be chosen within the range that the selected driver allows. The time frames T1 to T5 can be chosen freely to accommodate any requirement.

Programming the Dynadimmer

Dynadimmer Programming KitOncedefined,thedimmingshapecansimplybedownloadedintotheDynadimmerProgrammer.TheDynadimmerProgrammerthenenablesthe user to program the individual Dynadimmers on-site or off-site. The DynadimmerProgrammerispoweredby4AAorLR6batteriesforeasy on-site use.

TheDynadimmerProgrammerhas3buttons•On/Off(green),toswitchtheProgrammerOnand/orOff• Selectcorrectdimmingshape(orange),topreloadthedimming

shape that needs to be programmed in Dynadimmer SELV• Write(black),toactuallywritethedimmingshapeintoDynadimmer

SELVTheDynadimmerProgrammercontainsanLCDscreentoinformtheuser about action statuses.

Dynadimmer USB PC CableTheUSBProgrammingcableisacabletodirectlylinkandprogramDynadimmerSELVfromthePC.WhenusingthiscablenoProgrammertool is needed. The Dynadimmer software has a special button to activatetheUSBfeature.Inadditiontoprogramminganduploadingtheexistingdimmingschedule,anoptionisavailableformulti-programming.Withmulti-programming,connectingDynadimmerissufficienttoprogram it and there is no need to press any button on the computer. This is specially designed for factories to program large quantities in a very short time.

Released drivers

The drivers released to interact with the Dynadimmer’s 1-10V dimming interface are currently:PhilipsHF-RegulatorPL-T/CEII26-42WPhilipsHF-RegulatorPL-LEII24-55WPhilipsHID-DynaVision1-10V150SONPhilipsHID-DynaVision1-10V100SONPhilipsHID-DynaVision1-10V70SONPhilipsHID-DynaVision1-10V150CDOPhilipsHID-DynaVision1-10V100CDOPhilipsHID-DynaVision1-10V70CDOPhilipsHID-DynaVisionController1-10V250SONPhilipsHID-DynaVisionController1-10V400SON

Wiring the Dynadimmer SELV

Inaccordancewiththerequirementslaiddownintheregulationsrelatingtoluminaires(EN60589)

WarningCompletelyturnofftheexternalpowersupplywheninstallingor placing wiring.Notdoingsocouldcauseelectricshockorpersonalinjury.

WarningDisconnect mains power supply before connecting the DynadimmerProgrammertotheDynadimmerSELV.

LNNeutral

220-240V50/60Hz

Line

–+~

Dynadimmer SELVLLC7220/009137 003 38503Un: 220-240V~ 50/60Hzta: -40...+55°C tc: 75°C

9±0.5

0.5...1.5 mm2

Housing provides insulation for class IIMade in EUwww.philips.com

tc

SELV output

1-10V

+–

NN

LL

05

~ mainsLED Driver SELV

SELV

SELVClass I: basic insulationClass II: double insulation

Dynadimmer housing provides insulation class II

Dynadimmer SELV wiring diagram

Dynadimmer Software

Dynadimmer Programmer

Dynadimmer USB PC Cable

LLC7220Dynadimmer SELV

4/4

Technical data

Storage conditionsTemperature -40°C...+85°CRelativehumidity 5%...95%RH

Operating conditionsAmbienttemperature -40°C...+55°CCasetemperature 75°CRelativehumidity 10%...90%RH(nocondensation)

Mains connectionRatedvoltage 220-240V±10%Frequency 50/60Hz±5%Maximum load Not applicable

Mains / 1-10V connectionsConnectortype WAGO250CageClampDriversperDynadimmerSELV 2max.Wirerange 0.5...1.5mm2 solidWirestriplength 8.5...9.5mmPowerconsumption 1.2Wat230VAC/50Hz

Programming connectorConnectortype MicroMATE-N-LOKconnectorFactorysetting Afterpower-up,thecontrol voltagewillriseslowlyto+5VDC

Dim interfaceControlvoltage 1-10VMax.current 0.3mAsinkingDim curve Defined by selected driverProtection Protectedagainstaccidental connection with mains voltageOutputimpedance 2700ohm

NormsSafety EN61347-2-11;EN60598Immunity EN61547Emission CISPR15ed.7.1Approbation Productcomplieswiththe

relevantEuropeanDirective(CE) ENECEnvironment WEEE/RoHScompliant

Housing Protectionclass IP20Dimensions(HxWxL) 30mmx44.5mmx99.5mmWeight 0.085KgMaterial PC-GELEXAN223R-111Color BlackGlowwiretest ≥850°Cat1mmmaterial thicknessFlammability UL94-V2at0,75mmmaterial thickness UL94V0at6mmmaterial thicknessFixation M8x16bold(class8.8)or 2xM4screwwithcylinderheadTheLLC7220isdesignedtobebuiltintoaluminaire,abox,anenclosureorthelikeandisnotintendedtobemountedoutsidealuminaire,etc.withoutspecialprecautions.TheLLC7220housingprovidesinsulationforclassII.

Safety 1-10Vinterface Theinterfaceisdouble(SELV)

isolated from the mains supply. (4kVroutinetestfortransformer)Programminginterface Theinterfaceisdouble(SELV) isolated from the mains supply (4kVroutinetestfortransformer)

WarningMains has to be disconnected before connecting the programmer.

3226363611002/2010Data subject to change

www.philips.com/dynadimmer

Packing dataType Box dimensions Qty Material Weight (Kg) (mm) net grossLLC7220DynadimmerSELV 360x280x120 48 cardboard 4.08 4.60KIT7210Programmingkit 150x280x65 1 cardboard 0.73 0.83LCC7210/00USBPCCable 16.5 x 10 x 1.8 1 plasticbag 0.078 0.080

Ordering DataType MOQ Ordering number EAN code level 1 EAN code level 3 EOCLLC7220DynadimmerSELV 48 913700338503 n.a. 8727900881387 88138700KIT7210Programmingkit 1 913700334703 n.a. 8727900857177 85717700LCC7210/00USBPCCable 1 913700334603 8727900900576 8727900900583 90057600