lionel little lines freight set owner’s manual · pdf filelionel little lines freight...

Lionel Little Lines Freight Set

Owner’s Manual

71-1163-2507/09

Lionel Little Lines Freight.indd 1 12/29/09 1:53 PM

The following Lionel marks may be used throughout this instruction manual and are protected under law. All rights reserved.

Lionel®, TrainMaster®, Odyssey®, RailSounds®, CrewTalk™, TowerCom™, DynaChuff™, StationSounds™, Pullmor®, ElectroCoupler™, Magne-Traction®, CAB-1® Remote Controller, PowerMaster®, Lionel ZW®, ZW®, PowerHouse®, TMCC®, Lionelville™, Lockon®, Wireless Tether™, LionMaster®, FatBoy™, American Flyer®, TrainSounds™, PowerMax™, LEGACY™, PowerMax™ Plus, Odyssey II™, LEGACY RailSounds™

The name FasTrack® is used with permission from Pitsco, Inc.

INSTRUCTION FOR LIONEL LITTLE LINES FREIGHT SET

All Lionel Little Lines Engines have an Automatic Power Shut Off to conserve batteries. If the Controller is not used for 5 minutes the engine will go into the POWER OFF MODE. Press the Smoke Stack on the engine to restart. The POWER ON MODE in the Engine is indicated by the headlamp being illuminated.

CONTENTS:

Steam Engine (1)

Tender (1) Gondola Car (1) Caboose (1) IR Controller (1) Nine Inch Straight Track (2)Six Inch Straight Track (4)Three Inch Straight Track (3)Curve Track (5)Right Hand Switch (1)Left Hand Switch (1)Upper Elevation Track (2)Lower Elevation Track (2)On Ramp Track Section (1)Bumper Track Section (1) Stone Arches (8) Girder Bridge Half Sections (2)Suspension Bridge Half Sections (2) Freight Station W/Working Crane, Cargo Slide, and Two Way Loader/Dumper (1)Cargo Crates (2)Crossing Ramps, W/Gate and RR Sign (2)Billboard (1)Assorted Shaped Signs (3)

Note!


3

FCC Statement

This devise complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.

(1) Thisdevicemaynotcauseharmfulinterference,and

(2) Thisdevicemustacceptanyinterferencereceived.Includinginterferencethatmaycauseundesiredoperation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and , if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.


4

Battery installation (Requires Adult Installation)• Requires 6 “AAA” ALKALINE (RL03) batteries (not included) and a small Phillips screwdriver (not

included).

• Three batteries are used for the Controller and three are used for the Engine.

• Do not mix new and old batteries together.

• Lionel recommends using only Alkaline batteries for best performance .

• Never mix battery brand or types.

• Remove batteries if the toy is not to be used for an extended period.

Battery installation - Engine (Requires Adult Installation)

To open battery door loosen the two screws in the back of the engine cab with a Phillips screw driver.

Note: the screws will remain attached to the door after loosened. Open the battery door as shown and insert three “AAA” (LR03) ALKALINE batteries.

The Positive (+) and Negative (-) signs beneath the holes for the batteries indicate the end of the battery you should see when in place. You should see the Positive end of the top battery and the Negative end of the lower two.

After inserting the batteries close the door and tighten the screws. Be sure the screws are tightened snuggly to insure the good contact with the battery terminals. (Take care not to over tighten).

Battery installation - Controller (Requires Adult Installation)

To open battery door loosen the screw on the bottom of the controller with a Phillips screw driver. Lift battery door by tab near screw. Note: the screw will remain attached to the battery door

after loosened. Insert three “AAA” (LRO3) ALKALINE batteries positioned as shown in the back of the compartment. Replace the battery cover and tighten the screw to secure (Take care not to over tighten).

The switch at the bottom of the battery box allow the parent to turn off the sound features on this product. It is automatically preset to the Sounds On position. To turn the controller sounds off slide the switch to the alternate position). Sounds can be re-activated at any time by moving this switch back to the original Factory preset position.

Important!

Note!

REMOVE ALL BATTERIES WHEN THE TRAIN WILL NOT BE USED FOR AN EXTENDED PERIOD OF TIME.Important!


5

One-time assembly of upper and lower ramp track sections

THISISAONETIMEASSEMBLY.DONOTATTEMPTTOSEPARATETHESEPARTSINTHEFUTURE.

Align the Upper Ramp and Lower Ramp section together as shown. Press together firmly until they snap together. Ramp tracks are used to transition your train from the ground to a second level support by a Stone Arch.

Assembling track sections

Align the ends of the track and press firmly until they snap together.

Disassembling track sections

Hold track in both hands bending the joint downwards until the track snaps apart.

Note!


6

Stone arches

Stone Arches are used to support elevated sections of track. Place a Stone Arch under each joint section between the tracks and snap track into place as shown.

Stone Arches can also be stacked to create bridges or multiple levels of track. To stack the arches simply place the base of an arch over the top of another arch to snap into place

To separate arches simple bend them at the joint to snap apart

Suspension and grider bridge sections

To create bridges snap the suspension or girder bridges section onto the top of the arches as shown.

You must use a ‘9 INCH TRACK’ between the Brick Arches when using bridge sections.Note!

1). Place edgeof track under tab.

2). Then snapother edge down.

1). Push down.

1). Push down.

1). Push down.


7

Freight station assembly

Align and snap the Crane Support Structure into the Track Base as shown (NOTE: This is a onetime assembly).

Press the neck of the Crane into the hole in the top of the Crane Support Structure. It should turn freely after insertion (NOTE: This is a onetime assembly).

Slide the completed Crane assembly onto the Cargo Slide. The Cargo Slide can be removed for storage.

1). Slide in tabs.Base of crane

Bottom of sli

de loader

1). Push down.

1). Push down.


8

Freight station

To pick up crates with Crane squeeze the tops of the Cargo Grapple to open, then place over crate

and release. Squeeze again to release crate.

Lift the edge of the Cargo Slide to send crates down the Cargo Chute to the Loader/Dumper

Lift the tab on the Loader/Dumper to load cargo back into the Gondola Car.

Lift the other tab on the Loader/Dumper to dump Cargo next to station.

1). Lift up.

1). Squeeze in.

1). Lift up.

1). Lift up.


9

Switches

Your set comes with two switches.

Turn the signal light 90 degree or 1/4 turn to change the direction of the switch.

1). Rotate to switch tracks.

Go straight Follow curve


10

Track layout

Curve Curve

Curve

Upper ramp track

Lower ramp trackUpper

ramp track

Upper ramp track

On rampLeft

switch

Use 9" track for bridges

Bumper track

Right switch

Curve

Signs

3"3"

3"6"

6"

6"

9"

9"

6"Curve

Freight station


11

Signs

Your set comes with 1 Billboard sign and 3 other Assorted Signs.

These can be snapped onto the Accessory Notch located in the center of all Straight and Curved Track Sections. Slide the grooved portion of sign base under the edge of the accessory notch in the track and press together.

1). Push in.

1). Place under notch in track.2). Rest track on sign.

Crossing gate

Place the Rail Road Crossing sign into the keyed hole in the crossing base. NOTE: The Rail Road Crossing sign is not a permanent assembly and can be taken out. Center the Crossing Ramp with

any of the Accessory Notches on any of the straight tracks and press into place. The ramp should snap onto the side of straight tracks.


12

Train operation

Press down the Smoke Stack to turn power on in the engine. The light on the front of the train will turn on to indicate POWER ON MODE. The engine is now ready to use. If the engine is not used

for 5 min the engine will shut itself off to conserve batteries. The front light will turn off to indicate the POWER OFF MODE. To use the engine just press the smoke stack again turn POWER ON.

1). Push down.

2). Slide together.


13

IR Controller operation

Holding the controller as shown aiming it directly at the engine. Be sure there are no physical obstructions between the controller and the engine such as a bridge or brick arch.

Push the control lever forward to start the train moving FORWARD and start the running sounds. The lever will remain in this position to keep the train moving FORWARD and running sounds operating.

Pull the control lever backwards slightly to the STOP position bring the train to a stop.

Pull the lever all the way to the back to move the train in REVERSE and start running sounds. From REVERSE the lever will automatically return to the STOP position when the lever is released.

1). Forward 2). Stop 3). Reverse

Installing the battery in your controller

Using a Phillips head screwdriver, loosen the screw on the bottom of the controller. Note: the screws will remain

attached to the door after loosened. The Positive (+) and Negative (-) signs beneath the holes for the batteries indicate the end of the battery you should see when in place. Insert three “AAA” (LR03) ALKALINE batteries and replace the screw to secure the door in place.

1). Check Polarity!


14

Sound button

Prress the WHISTLE BUTTON while the train is in FORWARD or REVERSE to hear the train whistle.

To turn all sound off

To disable all sounds open the battery compartment on the Controller. When the battery door is removed there is a Sound Switch towards the front of the controller. The Sound Switch is set at

the factory to the ON position. Sliding this switch to the OFF position will disable all train sounds including those made when the sound button is pressed. To restore the sounds just move the switch back to the original ON position.

1). Slide switch

Push for whistle inforward or reverse

1). Forward 2). Reverse


15

Troubleshooting:

Trainwillnotrun:

• If the train controller is not used for more than 5 minutes the train will power down to conserve batteries. Press the smoke stack to activate the POWER ON MODE. Check if headlamp on front of train lights ups after button is pressed. If headlamp does not light up change batteries in engine.

• Be sure there are no physical obstructions between the controller and the sensor on top of the engine.

• Direct sunlight can interfere with the operation of any IR controller. Move the train and controller out of direct sunlight.

• Check to be sure the batteries are orientated properly. In the engine this means you should see the + side of on the top battery and the - side of the bottom two batteries. In the controller check to see if they are oriented as shown in the diagrams molded into the bottom of the battery compartments.

• Be sure the screws on the engines battery door are closed snuggly. The battery door must be fully closed for the battery contacts to be properly engaged.

• Put NEW batteries in the engine

• Put NEW batteries in the controller.

Soundsplaybuttrainwillnotmove:

• Be sure the screws on the engines battery door are closed snuggly. The battery door must be fully closed for the battery contacts to be properly engaged.

• Put NEW batteries in the engine

• Direct sunlight can interfere with the operation of any IR controller. Move the train and controller out of direct sunlight.

Trainmovesbutsoundsarenotplaying.

• Change the position of the slide switch in the bottom of the Controller’s battery compartment. This switch allows you to disable the sounds and should be preset in the ON position at the factory.

• Put NEW batteries in the Controller.


Lionel Limited Warranty Policy & Service

This Lionel product, including all mechanical and electrical components, moving parts, motors and structural components, with the exception of LIGHT BULBS, LED’s & TRACTION TIRES are warranted to the original owner-purchaser for a period of

one year from the original date of purchase against original defects in materials or workmanship when purchased through a Lionel Authorized Retailer*.

This warranty does NOT cover the following:

• Normal wear and tear• Light bulbs or LED’s• Defects appearing in the course of commercial use• Damage resulting from abuse/misuse of the product

Transfer of this product by the original owner-purchaser to another person voids this warranty in its entirety. Modification of this product in any way; visually mechanically or electronically, voids the warranty in its entirety.

Any warranted product which is defective in original materials or workmanship and is delivered by the original owner-purchaser (this warranty is non-transferrable) to Lionel LLC or any Lionel Authorized Service Station MUST be accompanied by the original receipt for purchase (or copy) from an Authorized Lionel Retailer*, will at the discretion of Lionel LLC, be repaired or replaced, without charge for parts or labor. In the event the defective product cannot be repaired, and a suitable replacement is not available, Lionel will offer to replace the product with a comparable model (determined by Lionel LLC), if available. In the event a comparable model is not available the customer will be refunded the original purchase price (requires proof of purchase from the Authorized Lionel Retailer* it was originally purchased). Any products on which warranty service is sought must be sent freight or postage prepaid (Lionel will refuse any package when postage is due). Transportation and shipping charges are not covered as part of this warranty.

NOTE: Products that require service that do not have a receipt from an LIONEL AUTHORIZED RETAILER* will be required to pay for all parts required to repair the product (labor will not incur a charge) providing the product is not older than 3 years from date of manufacture and is within 1 year from date of purchase. A copy of the original sales receipt is required.

In no event shall Lionel LLC be held liable for incidental or consequential damages.Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion may not

apply to you.This warranty gives you specific legal rights and you may have other rights which vary from state to state.

Instructions for Obtaining ServiceIf service for this Lionel LLC product is required; bring the item, along with your DATED sales receipt and completed warranty

information (at the bottom of this page) to the nearest Lionel Authorized Service Station. Your nearest Lionel Service Station can be found by calling 1-800-4-LIONEL or by accessing the website at www.lionel.com.

If you prefer to send your Lionel product directly to Lionel, for repair you must FIRST call 586-949-4100 extension 9105 or FAX Lionel at 586-949-5429 or write to Customer Service, 26750 Twenty Three Mile Road, Chesterfield, MI 48051-2493. Please have the 6-digit Lionel product number, the date of original purchase, the dealer where the item was purchased and what seems to be the problem. You will receive a return authorization (RA) number to ensure your merchandise will be properly tracked and handled upon receipt at Lionel LLC.

Once you have your Return Authorization (RA) number, make sure the item is packed in its original Styrofoam inner container which is placed inside the original outer display box (this will help prevent damage during shipping and handling). This shipment MUST be prepaid and we recommend that it be insured with the carrier of your choice.

Please make sure you have followed all of the above instructions carefully before returning any merchandise for service. You may choose to have your product repaired by one of Lionel LLC’s Authorized Service Stations after its warranty has expired. A reasonable service fee should be expected once the product warranty has expired.

Warranty InformationPlease complete the information below and keep it, along with your DATED ORIGINAL SALES RECEIPT. You MUST

present this form AND your DATED SALES RECEIPT when requesting warranty service.*A complete listing of Lionel Authorized retailers can be found by calling 1-800-4-LIONEL or by visiting our website at

www.lionel.com. Products that are more than 3 years old, from date of manufacture, are not applicable for warranty coverage, even if they

have never been sold prior to this date. (Under no circumstance shall any components or labor be provided free of charge.)

Name ��

Address ��

Place of Purchase ��

Date of Purchase ��

Product Number ��

Product Description ��

©2009 LIONEL L.L.C., U.S.A.PRINTED IN CHINA


lionel little lines freight set owner’s manual · pdf filelionel little lines freight...

Documents