lindab rainline assembley bg
TRANSCRIPT
Lindab Rainl ine | Assembly Instruct ions Roof Drainage System
Lindab Roof Drainage SystemAssembly instructions
Lindab Rainline TM
Lindab Rainl ine | Assembly Instruct ions Roof Drainage System
Lindab Roof Drainage SystemAssembly instructions
Lindab Rainline TM
Lindab Rainl ine | Assembly Instruct ions Roof Drainage System
Lindab Roof Drainage SystemAssembly instructions
Lindab Rainline TM
Lindab Rainl ine | Assembly Instruct ions Roof Drainage System
Lindab Roof Drainage SystemAssembly instructions
Lindab Rainline TM
Покривна водоотвеждаща система
Ръководство за монтаж
�
Lindab Rainl ine | Roof Drainage System
Before you startIt is the total area of the roof that decides the dimensions of the roof drainage sys-tem. The bigger the roof, the more water the system must take care of. It will pay in the long run to be careful when you measure your roof and calculate dimen-sions. Take your calculation to your local dealer, who will help you to pick out all the components you need. Please, also visit our web site www.lindab.se/xxxxx for dimensioning help.
Measure the roof area There are various types of roofs but measure each roof part by multiplying the roof length with the roof width. If the area is less than 50 m² use gutters with 100 mm width and pipes with 75 mm diameter. If the area is between 50-100 m² use gutters with 1�5 mm width and pipes with 87 mm diameter. If the area
is larger than 100 m² there are gutters with 150 mm width and pipes with 100 mm diameter or 190 mm gutters and 111/1�0 mm pipes. If there are differ-ent roof sizes on the same building the largest roof part is dimensional.
Number of brackets and drain pipesThe brackets should be mounted with c/c 600 mm. The end brackets are mounted 100 mm from the roof edge.
The inclination of the gutter towards the down pipe should be at least �,5 mm/m. Calculate how many brack-ets you need for each roof part (example 10 m/0,6 m +1 = 18 brack-ets). Each drain pipe covers maximum 10 m gutter fall (length of the house). For a estethic reasons or if the gutter fall exceeds 10 m, place pipes on each corner of the house.
Assembly instructions
Where to place the pipesThe pictures below show recomended placement of drainpipes for different houses.
Saddle roof. 1 or � per side. Hipped roof L-shaped roof
One downpipe for roof length less than 10 m Two downpipes for roof length exceeding 10 m
�
Lindab Rainl ine | Roof Drainage System
Assembly instructions
Transport, storage, unpackingMake sure that the roof drainage com-ponents are handled with care during transport, storage and unpacking. If not, the coating may be damaged or the pipes and gutters dented. Store pipes and gutters on a plane and sta-ble surface.
Non coated components must be un-packed and stored in a dry and venti-lated place.
CuttingCut the gutters and pipes with plate shears or a hacksaw on a firm underlay on the ground. Never use an angle grinder. It heats the steel up up and thus destroyes the galvanization. The coating may also be scorched by hot chips or filings.
Never use an angle grinder
After-treatmentIf the coating has been damaged, paint it with Lindab’s repair paint to prolong the lifespan of the roof drainage sys-tem. Use a sponge or Lindab’s paint nib.
MaintenanceIf you want to keep the roof drainage system in mint condition, give the sys-tem an overhaul a couple of times a year. Clean the gutter and pipes from leaves and twigs. Wash with water and a mild detergent. Don’t use a high pres-sure washing appliance.
ToolsLindab’s roof drainage system can be mounted with ordinary hand tools like pliers, hammer, hacksaw, screwdriver, folding rule and string. For bending brackets, you need a bracket bender. Contact your local dealer and they will lend you one.
FasteningThe fasteners you need are for fasten-ing the brackets and the pipe holders. We always recommend that you use stainless screws and use the right screws intended for each material. The pipe holders are mounted on the house façade. Check if it´s wood, concrete or bricks.
Spirit level
Electrical screw driver
Hack saw
Folding rule
Seam plier
Bracket bender
Pencil
Steel scissors
Rubber hammer
�
Lindab Rainl ine | Roof Drainage System
Assembly instructions
Transport, storage, unpackingMake sure that the roof drainage com-ponents are handled with care during transport, storage and unpacking. If not, the coating may be damaged or the pipes and gutters dented. Store pipes and gutters on a plane and sta-ble surface.
Non coated components must be un-packed and stored in a dry and venti-lated place.
CuttingCut the gutters and pipes with plate shears or a hacksaw on a firm underlay on the ground. Never use an angle grinder. It heats the steel up up and thus destroyes the galvanization. The coating may also be scorched by hot chips or filings.
Never use an angle grinder
After-treatmentIf the coating has been damaged, paint it with Lindab’s repair paint to prolong the lifespan of the roof drainage sys-tem. Use a sponge or Lindab’s paint nib.
MaintenanceIf you want to keep the roof drainage system in mint condition, give the sys-tem an overhaul a couple of times a year. Clean the gutter and pipes from leaves and twigs. Wash with water and a mild detergent. Don’t use a high pres-sure washing appliance.
ToolsLindab’s roof drainage system can be mounted with ordinary hand tools like pliers, hammer, hacksaw, screwdriver, folding rule and string. For bending brackets, you need a bracket bender. Contact your local dealer and they will lend you one.
FasteningThe fasteners you need are for fasten-ing the brackets and the pipe holders. We always recommend that you use stainless screws and use the right screws intended for each material. The pipe holders are mounted on the house façade. Check if it´s wood, concrete or bricks.
Spirit level
Electrical screw driver
Hack saw
Folding rule
Seam plier
Bracket bender
Pencil
Steel scissors
Rubber hammer
Двускатен покрив, 1 или 2 на страна (размер на стрехата)
Четирискатен покрив L – образен покрив
Една водосточна тръба при дължина на стрехата до 10 м
Две водосточни тръби при дължина на стрехата над 10 м
Преди да започнетеВсички размери на системата за водоотвеждане са в пряка зависимост от площта на покрива. Когато бъдат вземани покривните размери, е необходимо това да се направи мно го внимателно, след което се извършва изчисление за необходимите размери. След като размерите са свалени, моля свържете се с представител на компанията, който ще Ви окаже необходимото съдействие за избора на всички необходими компоненти на системата.
Размери на покриваСъществуват различни видове покриви, но необходимите размери се получават след умножаване на покривната ширина и височина. Ако площта на покрива е до 100 кв.м. се влагат улуци с диаметър 125 мм и водосточни тръби с диаметър 87 мм. При площ поголяма от 100 кв.м
Монтаж на покривна водоотвеждаща система
се използват улуци с диаметър 150 мм. и тръби с диаметър 100 мм. или улуци 190 мм и тръби 120 мм. Ако една сграда се състои от различни покривни площи, за определяне на размерите на елементите се взема под внимание найголямата от тях.
Брой скоби и тръбиРазстоянието между скобите се определя в зависимост от това през какво разстояние се поставят
носещите ребра на покривната конструкция, върху които с помощта на винтове се закрепват скобите. Обикновенно дистанцията между тях е 600 мм.Минималният наклон на улука в посока към водосточните тръби е 2.5 мм/м. Необходимо е да бъдат изчислени броят на скобите за улука (пример: 10 м/0.6 м + 1 = 18 скоби)
Gutter R
Gutter joint RSK
Nozzle SOK
Stop end RGT
Gutter angle, inner RVI Gutter angle, outer RVY
Adjustable bracket SSK
Bracket KFK
Bracket KFL
Stay strap STAG
Bracket K
Bracket for �7° roof pitch K11
Cover brace TB
Bend
Intermediate pipe MST
Bend BK70
Overflow protection, straight ÖSKR
Pipe holder SSVH
Pipe holder with spike
SSV
Shoe VTK
Downpipe SRÖR
Drain shoe BUTK
Self cleaning leaf trap SLS
Fold out shoe FUTK
Overflow protection, angle ÖSK
Bracket K
Sliding pipe PRT
Branch pipe GRÖR
Drain trap RT
Drain connector MRT
Components
�
Lindab Rainl ine | Roof Drainage System
Assembly instructions
Gutter R
Gutter joint RSK
Nozzle SOK
Stop end RGT
Gutter angle, inner RVI Gutter angle, outer RVY
Adjustable bracket SSK
Bracket KFK
Bracket KFL
Stay strap STAG
Bracket K
Bracket for �7° roof pitch K11
Cover brace TB
Bend
Intermediate pipe MST
Bend BK70
Overflow protection, straight ÖSKR
Pipe holder SSVH
Pipe holder with spike
SSV
Shoe VTK
Downpipe SRÖR
Drain shoe BUTK
Self cleaning leaf trap SLS
Fold out shoe FUTK
Overflow protection, angle ÖSK
Bracket K
Sliding pipe PRT
Branch pipe GRÖR
Drain trap RT
Drain connector MRT
Components
�
Lindab Rainl ine | Roof Drainage System
Assembly instructions
�
Lindab Rainl ine | Roof Drainage System
Assembly instructions
Transport, storage, unpackingMake sure that the roof drainage com-ponents are handled with care during transport, storage and unpacking. If not, the coating may be damaged or the pipes and gutters dented. Store pipes and gutters on a plane and sta-ble surface.
Non coated components must be un-packed and stored in a dry and venti-lated place.
CuttingCut the gutters and pipes with plate shears or a hacksaw on a firm underlay on the ground. Never use an angle grinder. It heats the steel up up and thus destroyes the galvanization. The coating may also be scorched by hot chips or filings.
Never use an angle grinder
After-treatmentIf the coating has been damaged, paint it with Lindab’s repair paint to prolong the lifespan of the roof drainage sys-tem. Use a sponge or Lindab’s paint nib.
MaintenanceIf you want to keep the roof drainage system in mint condition, give the sys-tem an overhaul a couple of times a year. Clean the gutter and pipes from leaves and twigs. Wash with water and a mild detergent. Don’t use a high pres-sure washing appliance.
ToolsLindab’s roof drainage system can be mounted with ordinary hand tools like pliers, hammer, hacksaw, screwdriver, folding rule and string. For bending brackets, you need a bracket bender. Contact your local dealer and they will lend you one.
FasteningThe fasteners you need are for fasten-ing the brackets and the pipe holders. We always recommend that you use stainless screws and use the right screws intended for each material. The pipe holders are mounted on the house façade. Check if it´s wood, concrete or bricks.
Spirit level
Electrical screw driver
Hack saw
Folding rule
Seam plier
Bracket bender
Pencil
Steel scissors
Rubber hammer
Никога не използвайте ъглошлайв
Инструкция за монтаж
Нивелир Метър Молив
Винтоверт Плоски клещи за шев Ножица за метал
Ножовка Инструмент за огъване на скоби Гумен чук
Транспортиране и складиранеУверете се че елементите на водотвеждащата система са опаковани, складирани и транспортирани внимателно. Ако това не е направено, покритието на елементите може да бъде наранено и да бъдат причинени изменения във формата на детайлите. Съхранявайте елементите на системата на равна и устойчива повърхност.Необходимо е компонентите, които не са защитени да бъдат покрити и складирани на сухо и проветриво място.
СрязванеСрязвайте улуците и тръбите с ножовка върху твърда и устойчива повърхност на земята. Никога не използвайте ъглошлайф, тъй като неговата употреба води до нарушаване на галванизирания слой. Също така, покритието може да бъде прогорено от стружки.
След обработкаАко покритието е било повредено, мястото трябва да бъде покрито с коригираща боя Lindab, за да се осигури дълъг експлоатационен период на системата. Използвайте тампон или Lindab четчица за нанасяне на боята.
ПоддръжкаАко желаете да запазите системата в първоначалния си вид, осъществявайте проверка поне два пъти годишно. Измивайте с вода и препарат за почистване. Не упражнявайте голям натиск върху елементите по време на почистване.
ИнструментиСистемата за водоотвеждане Lindab Rainline може да бъде монтирана с обикновени ръчни инструменти – клещи, чук, ножовка, винтоверт. За огъване на скобите е необходимо да се използва инструмент за огъване на скоби.Моля свържете се с представител на компанията, който ще Ви окаже необходимото съдействие.
Lindab препоръчва използването на инструменти носещи марката STUBAI.
Gutter R
Gutter joint RSK
Nozzle SOK
Stop end RGT
Gutter angle, inner RVI Gutter angle, outer RVY
Adjustable bracket SSK
Bracket KFK
Bracket KFL
Stay strap STAG
Bracket K
Bracket for �7° roof pitch K11
Cover brace TB
Bend
Intermediate pipe MST
Bend BK70
Overflow protection, straight ÖSKR
Pipe holder SSVH
Pipe holder with spike
SSV
Shoe VTK
Downpipe SRÖR
Drain shoe BUTK
Self cleaning leaf trap SLS
Fold out shoe FUTK
Overflow protection, angle ÖSK
Bracket K
Sliding pipe PRT
Branch pipe GRÖR
Drain trap RT
Drain connector MRT
Components
�
Lindab Rainl ine | Roof Drainage System
Assembly instructions
5
Lindab Rainl ine | Roof Drainage System
Roof baseDepending on the roof construction of the building different types of brackets can be used. An adjustable snap bracket is used in the assembly in-struction that follows. Other bracket applications are also shown as sepa-rate instructions. The brackets that can be used are:
Assembly – Roof Drainage System
Lindab KFM/KFL bracket
Lindab K16/K�1 bracketLindab K07 bracketLindab K11 bracket
Lindab SSK Adjustable snap bracket Lindab KFK bracket
5
Lindab Rainl ine | Roof Drainage System
Roof baseDepending on the roof construction of the building different types of brackets can be used. An adjustable snap bracket is used in the assembly in-struction that follows. Other bracket applications are also shown as sepa-rate instructions. The brackets that can be used are:
Assembly – Roof Drainage System
Lindab KFM/KFL bracket
Lindab K16/K�1 bracketLindab K07 bracketLindab K11 bracket
Lindab SSK Adjustable snap bracket Lindab KFK bracket
Покривна водоотвеждаща система компоненти
Скоба
Усилваща скоба
Скоба
Скоби за наклон до 27°
Капак
Външен ъгъл
Скоба
Олук
Съединителен елемент
Водосборнакутия
Вътрешен ъгъл
Коляно
Съединителнатръба
Съединителен елемент
Накрайникза капкиране
Коляно
Скоба спланка
Предпазител срещу преливане
Предпазител срещу преливане
Водосточнатръба
Накрайник за канализация
Скоба
Дренаж
Самопочистващ се дренаж
Маншон
Накрайник
Компоненти на системата
6
Lindab Rainl ine | Roof Drainage System
Bracket assembly
Mark out for the brackets SSK around the down pipe.
Fasten “high bracket” at the opposite end of roof base. The inclination to the pipe shall be �,5 mm/m.
The SSK bracket can be adjusted for different roof pitches.
Calculate your roof pitch and adjust the bracket accordingly.
Fasten the other brackets with c/c 600 mm along the string.
Fasten the “low bracket” �00 mm left to the down pipe mark.
Put a string between the high and low bracket. It will help you to place the other brackets.
a b α
1 1 �5°
1 1,�5 �8°
1 � �7°
1 �,5 ��°
1 � 18°
1 � 1�°
1 8 7°
1 ∞ 0°
Fasten the bracket right of the down pipe mark �,5 mm higher than the low bracket.
Use screwdriver to fold the tap forward for low inclinations and backwards for α ≥ ��°.
Assembly – Roof Drainage System
6
Lindab Rainl ine | Roof Drainage System
Bracket assembly
Mark out for the brackets SSK around the down pipe.
Fasten “high bracket” at the opposite end of roof base. The inclination to the pipe shall be �,5 mm/m.
The SSK bracket can be adjusted for different roof pitches.
Calculate your roof pitch and adjust the bracket accordingly.
Fasten the other brackets with c/c 600 mm along the string.
Fasten the “low bracket” �00 mm left to the down pipe mark.
Put a string between the high and low bracket. It will help you to place the other brackets.
a b α
1 1 �5°
1 1,�5 �8°
1 � �7°
1 �,5 ��°
1 � 18°
1 � 1�°
1 8 7°
1 ∞ 0°
Fasten the bracket right of the down pipe mark �,5 mm higher than the low bracket.
Use screwdriver to fold the tap forward for low inclinations and backwards for α ≥ ��°.
Assembly – Roof Drainage System
5
Lindab Rainl ine | Roof Drainage System
Roof baseDepending on the roof construction of the building different types of brackets can be used. An adjustable snap bracket is used in the assembly in-struction that follows. Other bracket applications are also shown as sepa-rate instructions. The brackets that can be used are:
Assembly – Roof Drainage System
Lindab KFM/KFL bracket
Lindab K16/K�1 bracketLindab K07 bracketLindab K11 bracket
Lindab SSK Adjustable snap bracket Lindab KFK bracketСкоби Lindab: Lindab KFL скоби Lindab KFK скоби
Lindab K11 скоби Lindab K07 скоби Lindab K21, К33 скоби
ЕлементиВ зависимост от покривната конструкция се използват различни видове скоби.
Монтаж на покривна водоотвеждаща система
6
Lindab Rainl ine | Roof Drainage System
Bracket assembly
Mark out for the brackets SSK around the down pipe.
Fasten “high bracket” at the opposite end of roof base. The inclination to the pipe shall be �,5 mm/m.
The SSK bracket can be adjusted for different roof pitches.
Calculate your roof pitch and adjust the bracket accordingly.
Fasten the other brackets with c/c 600 mm along the string.
Fasten the “low bracket” �00 mm left to the down pipe mark.
Put a string between the high and low bracket. It will help you to place the other brackets.
a b α
1 1 �5°
1 1,�5 �8°
1 � �7°
1 �,5 ��°
1 � 18°
1 � 1�°
1 8 7°
1 ∞ 0°
Fasten the bracket right of the down pipe mark �,5 mm higher than the low bracket.
Use screwdriver to fold the tap forward for low inclinations and backwards for α ≥ ��°.
Assembly – Roof Drainage System
7
Lindab Rainl ine | Roof Drainage System
Gutter assembly
Place the gutter in the brackets and mark out for the gutter outlet SOK on the gutter.
Finish by cutting up to the bead and backside as shown in picture.
The gutter outlet snaps easily on the gutter. Cut or fold the ear not used.
Place the gutter in the brackets. Just snap on the bracket hooks on the gutter.
To get a smooth water fall, use a hammer on the edges.
Use the outlet as template on the gutter. Use a hacksaw to make a hole in the gutter.
The stop end RGT is self sealing. Use a rubber hammer to fix it to the gutter.
Assembly – Roof Drainage System
6
Lindab Rainl ine | Roof Drainage System
Bracket assembly
Mark out for the brackets SSK around the down pipe.
Fasten “high bracket” at the opposite end of roof base. The inclination to the pipe shall be �,5 mm/m.
The SSK bracket can be adjusted for different roof pitches.
Calculate your roof pitch and adjust the bracket accordingly.
Fasten the other brackets with c/c 600 mm along the string.
Fasten the “low bracket” �00 mm left to the down pipe mark.
Put a string between the high and low bracket. It will help you to place the other brackets.
a b α
1 1 �5°
1 1,�5 �8°
1 � �7°
1 �,5 ��°
1 � 18°
1 � 1�°
1 8 7°
1 ∞ 0°
Fasten the bracket right of the down pipe mark �,5 mm higher than the low bracket.
Use screwdriver to fold the tap forward for low inclinations and backwards for α ≥ ��°.
Assembly – Roof Drainage System
Водосборното казанче се захваща за улука с едно щракване
Отрежете или огънете ухото на капак RGT, което не се използва.
Капакът е самозатварящ се. Използвайте гумен или пластмасов чук, за да фиксирате капакът върху улука.
Поставете улука върху скобите. В зависимост от вида на използваните скоби, фиксирайте с едно щракване улука съобразно инструкциите.
Поставете улука на скобите и маркирайте местоположението на водосборното казанче SOK.
Използвайте водосборното казанче като шаблон и очертайте.
С помощта на ножовка направете отвор в улука.
Довършете сряза, както е показано на картинката.
За да направите ръб срещу подлизване на водата използвайте пластмасов или гумен чук.
Монтаж на улук
Инструкция за монтаж на улук
Използването на ъглошлайф не е препоръчително, тъй като това води до нарушаване на защитния слой.
8
Lindab Rainl ine | Roof Drainage System
Gutter joint
Place the gutter to be jointed in the brackets and mark out the needed length
Snap on the gutter.
Snap on the gutter joint
Use self sealing RSK gutter joint.
Use a hack saw to cut the gutter.
Assemble the stop end RGT.
Silicone should not be used.
Remove the filings.
Press the sealing to the gutter. and lock.
Assembly – Roof Drainage System
Захванете улуците към скобите Използвайте съединителния елемент с уплътнение RSK.
Заключете.
Поставете улуците в скобите и ги доближете до необходимата дистанция за съединяване. Маркирайте необходимата дължина.
Използвайте ножовка, за да срежете улука.
Внимателно отстранете стърготините.
Монтирайте капака за затваряне на улука
Свързване на улуци
Не е препоръчително да се използва силикон.
Притиснете съединителния елемент към улука.
Захванете към улука и щракнете.
Свързване на улуци
8
Lindab Rainl ine | Roof Drainage System
Gutter joint
Place the gutter to be jointed in the brackets and mark out the needed length
Snap on the gutter.
Snap on the gutter joint
Use self sealing RSK gutter joint.
Use a hack saw to cut the gutter.
Assemble the stop end RGT.
Silicone should not be used.
Remove the filings.
Press the sealing to the gutter. and lock.
Assembly – Roof Drainage System
9
Lindab Rainl ine | Roof Drainage System
Down pipe bends
Check the measures to get the length of the intermediate pipe MST. Use table on the side.
Measure the length of the down pipe. Mark out for the pipe holders SSVH
Assemble the pipe Shoe UTK. Use a self tapping screw on the back side.
Level the pipe holders with spirit level or plummet.
Fasten the pipe holder on the wall.
Use a hack saw to cut the intermediate pipe MST. Remove sharp metal filings with a knife.
Intermediate pipelength at 70° bends
Umm
Hmm
Lmm
��0 �75 0
�70 �90 100
�00 �00 1�5
�50 ��0 185
�00 ��0 ��0
�50 �55 �90
500 �75 ��5
550 �95 �00
600 �10 �55
650 ��0 505
700 �50 560
750 �65 610
800 �85 665
850 505 7�0
900 5�0 770
950 5�0 8�5
1000 555 880
1050 575 9�0
1100 595 985
1150 610 10�0
1�00 6�0 1090
Assembly – Roof Drainage System
Down pipe and and holder
Измерете дължината на водосточната тръба. Маркирайте местоположението на скобите SSVH.
Монтирайте накрайника за водосточна тръба UTK. Използвайте самонарезен винт откъм задната страна.
Проверете разположението на скобите SSVH с отвес или нивелир.
Закрепете скобите SSVH към стената.
Проверете размерите, за да определите дължината на междинния удължител MST.
Използвайте ножовка, за да срежете междинния удължител MST. Внимателно премахнете стружките.
Коляно за водосточна тръба
Водосточна тръба и скоба
Монтаж на покривна водоотвеждаща система
10
Lindab Rainl ine | Roof Drainage System
Close up assembly pipe holder SSVH
It´s easily done to dismount the holder.
Assembly – Roof Drainage System
Стъпка 4
Закопчаване на скоба SSVH
Монтаж на покривна водоотвеждаща система
Стъпка 1 Стъпка 2 Стъпка 3
10
Lindab Rainl ine | Roof Drainage System
Close up assembly pipe holder SSVH
It´s easily done to dismount the holder.
Assembly – Roof Drainage System
11
Lindab Rainl ine | Roof Drainage System
Bracket KFK
Bracket K07
Alternative to use bracket KFK for perpendicular roof base.
Alternative to use bracket K for perpendicular roof base.
The inclination shall be �,5 mm/m.
The inclination shall be �,5 mm/m.
Assembly – Roof Drainage System
Скоба за челна дъска
Скоба за челна дъска
Min наклон на улука 2.5 mm/m
LINDAB KFK скоби
Min наклон на улука 2.5 mm/m
LINDAB K07 скоби
Монтаж на покривна водоотвеждаща система
1�
Lindab Rainl ine | Roof Drainage System
Bracket K11
Bracket KFM/KFL
Use bracket K11 for �7° roof pitch.
Alternative to use bracket KFL Mark out on the brackets for the gutter incline. �,5 mm/m.
Bend the brackets at the marking.
Number the brackets. 1 is for “Low bracket”. Last bracket is ”High bracket”.
The inclination shall be �,5 mm/m.
Mount bracket no.1 “Low bracket”, and fasten the other brackets accordingly.
Assembly – Roof Drainage System
KFL скоби Маркирайте от външната страна на скобите с молив. По този начин ще определите наклона на улука, като минималната му стойност е 2.55 мм/м.
Започнете с монтирането на скоба №1 и продължете с останалите.
Скобите К 11 се използват за челна дъска на покрив с наклон 27°
Min наклон на улука 2.5 mm/m
Lindab K 11 скоби
Огънете скобата на мястото на маркировката.
Номерирайте скобите, като №1 е скобата, която се намира на найниско ниво, а последната скоба се намира на найвисокото ниво.
Lindab KFL скоби
Монтаж на скоби
1�
Lindab Rainl ine | Roof Drainage System
Bracket K11
Bracket KFM/KFL
Use bracket K11 for �7° roof pitch.
Alternative to use bracket KFL Mark out on the brackets for the gutter incline. �,5 mm/m.
Bend the brackets at the marking.
Number the brackets. 1 is for “Low bracket”. Last bracket is ”High bracket”.
The inclination shall be �,5 mm/m.
Mount bracket no.1 “Low bracket”, and fasten the other brackets accordingly.
Assembly – Roof Drainage System
1�
Lindab Rainl ine | Roof Drainage System
Traditional Stop end RGV and RGH
Use silicone as sealing.
Traditional gutter joint
Use silicone as sealing.
Assembly – Roof Drainage System
Използвайте силикон за уплътнение
Използвайте силикон за уплътнение
Традиционно съединяване на улуци
Традиционно затапване на улуци
Монтаж на покривна водоотвеждаща система
1�
Lindab Rainl ine | Roof Drainage System
Gutter angle RVI/RVY
Spike STI with Pipe holder SSV
Use the gutter joint RSK.
Overflow protection ÖSK and ÖSKR
Cover brace TB
Place Overflow protection ÖSKR in the gutter.
Cut off the front fold piece on the old bracket. Place the cover brace TB over the old bracket.
Overflow protection ÖSK for gutter angles.
Gutter joint RSK.
Assembly – Roof Drainage System
Предпазители срещу преливане OSK и OSKR
Вътрешни и външни ъгли RVI и RVY
Скоба SV с клин SST.
Поставете елемента и го захванете към улука със съединителен елемент RSK.
Поставете предпазителя срещу преливане OSKR в улука.
Поставете предпазителя срещу преливане OSK за вътрешен ъгъл.
Инструкция за монтаж
1�
Lindab Rainl ine | Roof Drainage System
Gutter angle RVI/RVY
Spike STI with Pipe holder SSV
Use the gutter joint RSK.
Overflow protection ÖSK and ÖSKR
Cover brace TB
Place Overflow protection ÖSKR in the gutter.
Cut off the front fold piece on the old bracket. Place the cover brace TB over the old bracket.
Overflow protection ÖSK for gutter angles.
Gutter joint RSK.
Assembly – Roof Drainage System
15
Lindab Rainl ine | Roof Drainage System
Adjustable shoe FUTK
Adjustable branch GRÖR
Leaf filter DVSIL
Drain trap RT
Connect a branch pipe. Can be mounted in angle 50-80°.
Connect the drain shoe BUTK
Connect the sliding pipe PRT.Place the drain trap in the ground pipe. You can also use a self cleaning leaf trap SLS.
Assembly – Roof Drainage System
Накрайник за каптиране на вода FUTK
PVC самопочистващ се дренаж SLS
Съединителен елемент GROR
Накрайник за връзка с канализацията BUTK
PVC дренаж за ръчно почистване RT
Инструкция за монтаж
Lindab Profile is a business area within the Lindab
Group that develops, manufactures, and markets
efficient, economical and aesthetic steel and sheet-
metal solutions for the building industry.
We offer everything from complete building systems to
individual building components for all types of housing,
as well as commercial and industrial buildings.
Lindab Profile is represented in over �5 countries
throughout Europe. Our head office is in Förslöv,
in the south of Sweden.
SE-269 82 BåstadPhone +46 (0)431 850 00www.lindab.com
Lindab Profile
Lindab Rainl ine | Assembly Instruct ions Roof Drainage SystemA
rt n
o. X
XX
XX
X 2
007-
03-2
3
Lindab Profile is a business area within the Lindab
Group that develops, manufactures, and markets
efficient, economical and aesthetic steel and sheet-
metal solutions for the building industry.
We offer everything from complete building systems to
individual building components for all types of housing,
as well as commercial and industrial buildings.
Lindab Profile is represented in over �5 countries
throughout Europe. Our head office is in Förslöv,
in the south of Sweden.
SE-269 82 BåstadPhone +46 (0)431 850 00www.lindab.com
Lindab Profile
Lindab Rainl ine | Assembly Instruct ions Roof Drainage System
Art no
. X
XX
XX
X 2007-03-23
Lindab Profile is a business area within the Lindab
Group that develops, manufactures, and markets
efficient, economical and aesthetic steel and sheet-
metal solutions for the building industry.
We offer everything from complete building systems to
individual building components for all types of housing,
as well as commercial and industrial buildings.
Lindab Profile is represented in over �5 countries
throughout Europe. Our head office is in Förslöv,
in the south of Sweden.
SE-269 82 BåstadPhone +46 (0)431 850 00www.lindab.com
Lindab Profile
Lindab Rainl ine | Assembly Instruct ions Roof Drainage System
Art
no.
XX
XX
XX
200
7-03
-23
Линдаб груп е международна
корпорация, която развива, произвежда и
продава продукти от листова стомана
и предлага решения в бизнес областите
Вентилация и Профили.
Ние от Линдаб България сме се
насочили към продажба на ефикасни,
икономични и естетични стоманени и
ламаринени решения за строителната
индустрия.
Ние предлагаме всичко, от цялостни
строителни системи до индивидуални
компоненти за всички видове къщи,
както и за търговски и идустриални
сгради.
Линдаб ЕООДСофия 1592
ул. Капитан Д. Списаревски 38тел. (02) 979 97 00факс (02) 979 97 01
e-mail: [email protected]
Lindab Rainl ine | Assembly Instruct ions Roof Drainage System
Lindab Roof Drainage SystemAssembly instructions
Lindab Rainline TM