limits fits and tolerances metrology
DESCRIPTION
aTRANSCRIPT
![Page 1: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/1.jpg)
LIMITS AND FITS
![Page 2: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/2.jpg)
CONTENTS LIMTS FITS AND TOLERANCES INSPECTION TYPES OF INSPECTION
![Page 3: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/3.jpg)
TERMINOLOGY NOMINAL SIZE: It is
the size of a part specified in the drawing.
BASIC SIZE: It is the size of a part to which all limits of variation are determined.
ACTUAL SIZE: It is the actual measured dimension of a part. Nominal and basic size are often the same.
![Page 4: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/4.jpg)
LIMIT OF SIZES There are two
extreme possible sizes of a component.
The largest permissible size for a component is called upper limit and smallest size is called lower limit.
![Page 5: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/5.jpg)
DEVIATION
It is the algebraic difference between any given size and actual size.
ACTUAL DEVIATION: It is the algebraic difference between the actual size and the basic size.
![Page 6: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/6.jpg)
DEVIATION LOWER
DEVIATION: It is the algebraic difference between the minimum limit of size and the basic size.
UPPER DEVIATION: It is the algebraic difference between the maximum limit and the basic size.
![Page 7: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/7.jpg)
ZERO LINE It is the
straight line corresponding to the basic size. The deviations are measured from this line.
![Page 8: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/8.jpg)
![Page 9: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/9.jpg)
NATURAL VARIABILITY OF PROCESS It is the variation occurred in the size
due to natural conditions like variations in material, environmental fluctuations, vibrations, human variability etc. It is an unavoidable process.
![Page 10: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/10.jpg)
POSITIONAL TOLERANCES Two types of positional tolerances are
used:1. Unilateral tolerances2. Bilateral tolerances When tolerance is on one side of basic
size, it is called unilateral and if it is both in plus and minus then it is known as bilateral tolerance.
![Page 11: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/11.jpg)
FITS The degree of
tightness or looseness between two mating parts is called a fit.
![Page 12: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/12.jpg)
TYPES OF FITS CLEARANCE FIT:
There is a clearance or looseness in this type of fits. These fits maybe slide fit, easy sliding fit, running fit etc.
![Page 13: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/13.jpg)
TYPES OF FITS INTERFERENCE FIT: There is an
interference or tightness in these type of fits. E.g. shrink fit, heavy drive fit etc.
![Page 14: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/14.jpg)
TYPES OF FITS TRANSITION FIT:
In this type of fit, the limits for the mating parts are so selected that either a clearance or interference may occur depending upon the actual size of the mating parts.
![Page 15: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/15.jpg)
BASIS OF LIMIT SYSTEM1. HOLE BASIS
SYSTEM: In this system, the hole is kept as a constant member and different fits are obtained by varying the shaft size.
![Page 16: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/16.jpg)
BASIS OF LIMIT SYSTEM SHAFT BASIS
SYSTEM: In this system, the shaft is kept as constant member and different fits are obtained by varying the hole size.
![Page 17: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/17.jpg)
DIFFERENT LIMIT SYSTEMS1. The Newall system2. British Standard system3. International Federation of National
Standardization Association (ISA) system
4. ISO system5. ISI system
![Page 18: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/18.jpg)
INSPECTION Inspection is defined as a process used
for controlling and checking the quality of a product to the laid quality standards.
![Page 19: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/19.jpg)
OBJECTIVES OF INSPECTION1. It separates the defective components
from non-defective ones.2. By doing so, a defective product is
rejected before reaching to the customer.
3. It prevents the further work to be done on the defective product.
4. It helps the companies to sustain their reputation by maintaining quality standards.
5. To find out the defects in raw materials and errors in workmanship.
![Page 20: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/20.jpg)
FUNCTIONS OF INSPECTION1. Inspection of incoming material2. Inspection during manufacturing3. Mechanical and metallurgical
inspection4. Tool inspection5. Finished goods inspection
![Page 21: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/21.jpg)
DECISIONS ABOUT INSPECTION
![Page 22: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/22.jpg)
TYPES OF INSPECTION Based upon method of inspection1. Remedial inspection2. First-off inspection3. In-process inspection4. Operation inspection5. Sampling inspection6. Final inspection7. Pilot-piece inspection8. Final assembly inspection
![Page 23: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/23.jpg)
TYPES OF INSPECTION BASED UPON LOCATION1. Centralized or crib inspection2. Floor inspection
![Page 24: Limits Fits and Tolerances metrology](https://reader031.vdocuments.site/reader031/viewer/2022012303/5695cf601a28ab9b028dd586/html5/thumbnails/24.jpg)
THANK YOU