light box dimensions
DESCRIPTION
ÂTRANSCRIPT
![Page 1: Light box dimensions](https://reader034.vdocuments.site/reader034/viewer/2022042900/568c0f8f1a28ab955a948b7a/html5/thumbnails/1.jpg)
Marine Corps Community Services
Retail Division, Camp Lejeune
Register Signing Standards
Prepared For
Marine Marts, Retail Division
Marine Corps Community Services
Retail Division
July 16, 2013
![Page 2: Light box dimensions](https://reader034.vdocuments.site/reader034/viewer/2022042900/568c0f8f1a28ab955a948b7a/html5/thumbnails/2.jpg)
LIGHT BOX ILLUSTRATION
Figure 1
1
![Page 3: Light box dimensions](https://reader034.vdocuments.site/reader034/viewer/2022042900/568c0f8f1a28ab955a948b7a/html5/thumbnails/3.jpg)
LIGHTBOX DIMENSIONS
8.5”
3”
11.5”8.
5”
?All measurements are in inches?Sign is four sided
2
![Page 4: Light box dimensions](https://reader034.vdocuments.site/reader034/viewer/2022042900/568c0f8f1a28ab955a948b7a/html5/thumbnails/4.jpg)
LIGHTBOX POSITIONING
3
ON
OFF
FLASH
4’ 6”
?Lightbox is attached to existing electric pole
?Lightbox is positioned 4’ 6” from counter top
?Control switch is positioned 2 feet from counter top
Control Switch
Lightbox
Power pole
![Page 5: Light box dimensions](https://reader034.vdocuments.site/reader034/viewer/2022042900/568c0f8f1a28ab955a948b7a/html5/thumbnails/5.jpg)
LIGHT BOX ATTACHMENT
4
?Lightbox is attached to existing electric pole using two “L” brackets?Electrical light bulb housing is attached to power pole
Light bulb Housing
L BracketL Bracket
![Page 6: Light box dimensions](https://reader034.vdocuments.site/reader034/viewer/2022042900/568c0f8f1a28ab955a948b7a/html5/thumbnails/6.jpg)
LIGHT BOX POSITIONING
ON
OFF
FLASH
ON POSITION: The “ON” position is used to signal patrons that the register is open for service. When the switch is turned to the “ON” position the sign will be lighted.
OFF POSITION: The “OFF” position is used to signal patrons that the register is not in service.When the switch is turned to the “OFF” position the sign will not be lighted.
FLASH POSITION: The “FLASH” position is used to signal management that there is an issue at the cash register and assistance is needed. The “FLASH” position is located in the middle of the switch, between the ON and OFF positions.
5
![Page 7: Light box dimensions](https://reader034.vdocuments.site/reader034/viewer/2022042900/568c0f8f1a28ab955a948b7a/html5/thumbnails/7.jpg)
LIGHT BULB
6
?40 watt light bulb is used to light sign?Light bulb should be soft white?A fluorescent energy saving light bulb should be used
![Page 8: Light box dimensions](https://reader034.vdocuments.site/reader034/viewer/2022042900/568c0f8f1a28ab955a948b7a/html5/thumbnails/8.jpg)
COLOR STANDARDS
Cyan 100Magenta 72Yellow 0Black 32
Red 10Green 31Blue 98
Cyan 0Magenta 100Yellow 79Black 20
Red 196Green 18Blue 48
WhitePantone 281 Pantone 187
The MCX System’s primary color palette consists of blue and red. Secondary colors consist of yellow and white. One way to assure color consistency is to use the Pantone Color System. If a Pantone Color System cannot be used, then process color may be used. The four-color process equivalents for MCX’s Pantone Colors are shown above.
The colors shown in the manual have not been evaluated by Pantone Inc. for accuracy and may not match this Pantone Color Standard. Pantone is a registered trademark of Pantone, Inc. Pantone
7